CipherLab 8231 Terminal User Manual 8231 Reference Manual v1 05E 0625

CipherLab Co., Ltd. Terminal 8231 Reference Manual v1 05E 0625

Users Manual

8200 Series Terminal 8200/8231/8260 Version 1.05E
Copyright © 2009~2014 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing. CIPHERLAB does not warrant that this document is error-free. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of CIPHERLAB CO., LTD. For product consultancy and technical support, please contact your local sales representative. Also, you may visit our web site for more information. The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD. All brand, product and service, and trademark names are the property of their registered owners. The editorial use of these names is for identification as well as to the benefit of the owners, with no intention of infringement. CIPHERLAB CO., LTD. Website: http://www.cipherlab.com
FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FOR CANADA This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:  This device may not cause interference; and  This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :  l’appareil ne doit pas produire de brouillage;  l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. IMPORTANT NOTICES
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. FOR HAND-HELD PRODUCT WITH RF FUNCTIONS This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. It only operated in hand-held used. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no-collocation statement.
If you only transfer data to the host wirelessly, please keep the minimum distance 20 cm between machine & your body. FOR PRODUCT WITH LASER CAUTION This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. SAFETY PRECAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  The use of any batteries or charging devices, which are not originally sold or manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.  DO NOT disassemble, incinerate or short circuit the battery.  DO NOT expose the scanner or the battery to any flammable sources.  For green-environment issue, it's important that batteries should be recycled in a proper way.  Under no circumstances, internal components are self-serviceable. CARE & MAINTENANCE  This Terminal is intended for enterprise logistics use. The Terminal is rated IP 52, however, it may do damage to the Terminal when being exposed to extreme temperatures or soaked wet.  When the body of the Terminal gets dirty, use a clean and wet cloth to wipe off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.  For a liquid crystal display (LCD), use a clean, non-abrasive, lint-free cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move against the surface.  If you want to put away the Terminal for a period of time, download the collected data to a host computer, and then take out the battery pack. Store the Terminal and battery pack separately.  When the Terminal resumes its work, the main and backup batteries will take a certain time to become fully charged.  Keep the Terminal away from any magnets and magnetic fields to prevent the laser engine from malfunctioning.  If you shall find the Terminal malfunctioning, write down the specific scenario and consult your local sales representative. RELEASE NOTES
CONTENTS IMPORTANT NOTICES ...................................................................................................................... - 3 -For USA .......................................................................................................................................... - 3 -For Canada .................................................................................................................................... - 3 -For Hand-held Product with RF Functions ................................................................................... - 4 -For Product with Laser .................................................................................................................. - 5 -Safety Precautions ........................................................................................................................ - 5 -Care & Maintenance ..................................................................................................................... - 5 -RELEASE NOTES .............................................................................................................................. - 5 -INTRODUCTION .................................................................................................................................... 1Getting Familiarized with 8200 ........................................................................................................ 2Features ............................................................................................................................................. 3Inside the Package ............................................................................................................................ 3Accessories ........................................................................................................................................ 3Getting Started .................................................................................................................................. 4Inserting Battery & Memory Card ................................................................................................ 4Installing Pistol Grip ..................................................................................................................... 6Initial Charging ............................................................................................................................. 7Setting Local Time ........................................................................................................................ 7Power Management ..................................................................................................................... 7USING 8200 TERMINAL ...................................................................................................................... 91.1 Battery ......................................................................................................................................... 91.1.1 Main Battery ....................................................................................................................... 91.1.2 Backup Battery ................................................................................................................. 101.1.3 Caution of Low Battery Charge ........................................................................................ 101.2 Memory ..................................................................................................................................... 111.2.1 Read-only Memory (ROM) ................................................................................................ 111.2.2 Random-access Memory (RAM) ...................................................................................... 111.2.3 SD Card ............................................................................................................................. 111.3 Keypad ...................................................................................................................................... 121.3.1 24-key Layout ................................................................................................................... 121.4 LCD ............................................................................................................................................ 161.4.1 Adjusting the Backlight .................................................................................................... 161.5 Notifications .............................................................................................................................. 171.5.1 Status LED ........................................................................................................................ 171.5.2 Audio ................................................................................................................................. 181.5.3 Vibrator ............................................................................................................................. 181.6 Data Capture ............................................................................................................................. 191.7 Charging & Communications ................................................................................................... 211.7.1 Interface Cable Options ................................................................................................... 221.8 SD Card ..................................................................................................................................... 24
8200 Series Mobile Computer Reference Manual 1.8.1 File System ....................................................................................................................... 241.8.2 Directory ............................................................................................................................ 241.8.3 File Name .......................................................................................................................... 26LEARNING SOFTWARE ARCHITECTURE ............................................................................................. 272.1 Application Module ................................................................................................................... 292.1.1 FORGE Application Generator (AG) ................................................................................. 292.1.2 MIRROR Emulator (CipherNet) ........................................................................................ 302.1.3 User Program .................................................................................................................... 302.2 System Configuration & Core ................................................................................................... 302.2.1 System Menu .................................................................................................................... 312.2.2 Kernel ............................................................................................................................... 312.2.3 Program Manager ............................................................................................................ 31SYSTEM MENU................................................................................................................................... 333.1 Information ................................................................................................................................ 343.1.1 Understanding Device Code ............................................................................................ 353.2 Settings ..................................................................................................................................... 363.2.1 Clock ................................................................................................................................. 363.2.2 Backlight ........................................................................................................................... 363.2.3 Contrast ............................................................................................................................ 373.2.4 Auto Off ............................................................................................................................. 373.2.5 Power On (& Wakeup Event) Options.............................................................................. 373.2.6 Key Click ........................................................................................................................... 383.2.7 Speaker Volume ............................................................................................................... 383.2.8 USB VCOM No ................................................................................................................... 383.2.9 USB Charge Current ......................................................................................................... 383.2.10 Font ................................................................................................................................. 383.2.11 System Password ........................................................................................................... 393.2.12 Default Set ..................................................................................................................... 393.2.13 Reset Reader ................................................................................................................. 393.2.14 Upgrade Reader FW ....................................................................................................... 393.3 Tests .......................................................................................................................................... 403.3.1 Reader .............................................................................................................................. 403.3.2 Speaker ............................................................................................................................. 403.3.3 LCD & LED ........................................................................................................................ 403.3.4 Keyboard ........................................................................................................................... 403.3.5 Memory ............................................................................................................................. 403.3.6 Echo Test .......................................................................................................................... 413.3.7 Vibrator ............................................................................................................................. 413.4 Memory ..................................................................................................................................... 423.4.1 Size information ............................................................................................................... 423.4.2 Initialize ............................................................................................................................. 423.5 Power ......................................................................................................................................... 433.6 Load Program ........................................................................................................................... 443.7 DoFTP Menu .............................................................................................................................. 473.7.1 Local .................................................................................................................................. 483.7.2 Manual .............................................................................................................................. 483.8 SD Card Menu ........................................................................................................................... 493.8.1 Run as USB Disk .............................................................................................................. 493.8.2 Access SD Card ................................................................................................................ 49
8200 Series Mobile Computer Reference Manual 3.11 Bluetooth Menu ...................................................................................................................... 513.11.1 Information ..................................................................................................................... 523.11.2 Connect Setting .............................................................................................................. 533.11.3 Security ........................................................................................................................... 543.11.4 Echo Tests ...................................................................................................................... 553.11.5 Pairing Test..................................................................................................................... 583.11.6 Frequent Devices ........................................................................................................... 593.12 Wi-Fi Menu .............................................................................................................................. 603.12.1 Information ..................................................................................................................... 613.12.2 Network Setting ............................................................................................................. 623.12.3 WLAN Setting ................................................................................................................. 633.12.4 Security ........................................................................................................................... 653.12.5 Scan Devices .................................................................................................................. 663.12.6 Profile ............................................................................................................................. 673.12.7 Echo Tests ...................................................................................................................... 68PROGRAM MANAGER & KERNEL ...................................................................................................... 714.1 Program Manager ..................................................................................................................... 714.1.1 Download .......................................................................................................................... 724.1.2 Activate ............................................................................................................................. 744.1.3 Upload ............................................................................................................................... 754.2 Kernel ........................................................................................................................................ 764.2.1 Kernel Information ........................................................................................................... 774.2.2 Kernel Update .................................................................................................................. 784.2.3 Burn-In Test ...................................................................................................................... 804.2.4 System Menu .................................................................................................................... 80SPECIFICATIONS ................................................................................................................................ 81
1 Answering industrial demands for rugged, light-weight and versatile computers, the 8200 Series Terminal is specifically designed for enterprise logistics use. This line of product comes with built-in Bluetooth technology and allows for optional module for 802.11b/g/n connectivity, enabling real time sharing of performance. The 8200 Series Terminal is bundled with powerful and rich features to ensure success in timely processing of information, and thus, makes an ideal choice for inventory control, shop floor management, warehousing and distribution operations. Being programmable, this handy device can run custom applications or terminal emulation applications. This manual serves to guide you through how to install, configure, and operate the Terminal. We recommend you to keep one copy of the manual at hand for quick reference or maintenance purposes. To avoid any improper disposal or operation, please read the manual thoroughly before use. Thank you for choosing CipherLab products! INTRODUCTION
2 8200 Series Mobile Computer Reference Manual GETTING FAMILIARIZED WITH 8200 No. Description No. Description 1 Scanning window 2 LED for Good Read and battery charging 3 LED for wireless communications 4 LCD screen 5 Keypad, 24 keys 6 Wristband 7 Communication/charging port 8 Battery compartment Figure 1: Overview
3 Introduction FEATURES  Ergonomic design — ruggedized yet streamlined, with wristband for secure hold  Built tough to survive drop test and sealed against moisture/dust to IP 52  Rich interface options — USB  High capacity memory card (microSDHC) supported  Flexible wireless solutions — Bluetooth or 802.11b/g/n  FTP client support — 802.11b/g/n  Graphic monochrome LCD supports double-byte characters and bitmap graphics  Programmable feedback includes speaker, LED indicators and vibrator  Quick link to any backend database through MIRROR Emulator programs for VT100/220 and IBM 5250 emulation  Easy customization of data collection applications through FORGE Application Generator (AG) programs for preloaded AG Runtime, batch and WLAN versions available  Programming support includes BASIC & C compilers  Accessories include pistol grip INSIDE THE PACKAGE The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the Terminal.  8200 Series Terminal  Rechargeable Li-ion battery pack  Wristband  Standard USB cable  Universal power adaptor  Product CD  Quick Start Guide ACCESSORIES Rich choices of optional accessories are available for you to enhance the total performance of the Terminal.  Pistol Grip (detachable)  Protective Cover  Spare rechargeable Li-ion battery
4 8200 Series Mobile Computer Reference Manual GETTING STARTED INSERTING BATTERY & MEMORY CARD For shipping and storage purposes, save the Terminal and the main battery in separate packages. This will keep both batteries in good condition for future use. Note: Any improper handling may reduce the battery life. 1) Hold the Terminal still and slide the release latch to the right to unlock the battery cover. 2) Slide off the battery cover. 3) Use your finger to slide the locking plate towards its hinge to unlock the SD card holder. 4) Flip up the SD card holder. 5) Insert your memory card (microSD or microSDHC) to the SD card holder. 6) Push the SD card holder down. 7) Slide the locking plate away from its hinge to secure the card. 8) Slide the battery pack into the battery compartment at a proper angle (30°~45°) so that the metal contacts of the battery are met with the charging contacts inside the compartment. Make sure that the battery is snugly fit into the compartment. 9) Replace the battery cover. 10) Slide the release latch to the left to lock it firmly. Note: For a new battery, make sure it is fully charged before use. Always prepare a spare battery pack, especially when you are on the road.
5 Introduction Figure 2: Installing the Main Battery & Memory Card Unlock Lock
6 8200 Series Mobile Computer Reference Manual INSTALLING PISTOL GRIP This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications. When a pistol grip is necessary, install it to the Terminal by following these steps: 1) Hold the Terminal still and slide the release latch to the right to unlock the battery cover. 2) Slide off the battery cover. 3) Insert the pistol grip into place (is like replacing the battery cover). 4) Slide the release latch to the left to lock it firmly, and turn on the Terminal to test the trigger. Figure 3: Installing the Pistol Grip
7 Introduction INITIAL CHARGING The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge the main battery to full before using the Terminal. Instead of direct charging. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. For initial charging, it takes approximately 2.5 hours to charge the battery to full (from the adaptor). Because the internal backup battery is constantly charged from the main battery, the initial charging requires inserting the battery pack to the Terminal for charging. This will have both the main and backup batteries charged at the same time. It takes at least 72 hours to fully charge the backup battery. However, it is not necessary to fully charge the backup battery for the Terminal to work. Note: In order to charge the backup battery to full, you must insert the main battery and leave it for at least 72 hours, whether the Terminal is in use or not. SETTING LOCAL TIME If you need to set your local time, go to System Menu | 2. Settings | 1. Clock. Refer to 3.2.1 Clock. POWER MANAGEMENT For any portable device, power management is a critical issue especially when you are on the road. Below are some tips to help you save battery power. Warning: Using backlight, wireless connectivity, and peripherals while on battery power will substantially reduce battery power.  To speed up charging the Terminal, turn off the Terminal and use the charging/communication cable.  Bring a second battery pack on the road.  Stop wireless connectivity, Bluetooth or 802.11b/g/n that is not in use.  Go to System Menu | 2. Settings | 2. Backlight, and configure backlight period, luminosity, as well as the shade effect. Refer to 3.2.2 Backlight.  Go to System Menu | 2. Settings | 4. Auto Off, and configure the amount of idle time that must pass before the system will shut down automatically. Refer to 3.2.4 Auto Off.
9 This chapter explains the features and usage of the 8200 Series Terminal. The 8200 family includes:  8200 Batch type  8231 Bluetooth 2.1+EDR / BLE, Class 2; 802.11b/g/n  8260 Bluetooth 2.1+EDR, Class 2 IN THIS CHAPTER 1.1 Battery ....................................................................... 9 1.2 Memory .................................................................... 11 1.3 Keypad ..................................................................... 12 1.4 LCD ......................................................................... 16 1.5 Notifications .............................................................. 17 1.6 Data Capture ............................................................ 19 1.7 Charging & Communications ........................................ 21 1.8 SD Card ................................................................... 24 1.1 BATTERY 1.1.1 MAIN BATTERY The Terminal is powered by a rechargeable 3.7 V/1200 mAh Li-ion battery pack. When the Terminal is turned on, it takes approx. 2.5 hours to charge it to full from the power adaptor (using cable) or approx. 4 hours from the USB cable (at 500 mA). For power-saving purpose, always turn off the backlight while working in a well-lit area. When the backlight is on for extended periods of time, the main battery will become low sooner than expected. The smart battery icon on the LCD screen shows the status of power consumption. There are two ways to monitor a low battery charge or discharged battery from the screen.  Examine the level of the 4-bar battery icon  Monitor voltage level (see 3.5 Power) Chapter 1 USING 8200 TERMINAL
10 8200 Series Mobile Computer Reference Manual 1.1.2 BACKUP BATTERY The backup battery on the main board takes charge when the main battery is removed or drained out. When fully charged, the 3.0 V/18 mAh rechargeable Lithium button cell helps retain data in SRAM and maintain the running of the real-time clock and calendar for at least 25 days without the main battery. In the meantime, you have to replace the main battery as soon as possible. It takes at least 72 hours to fully charge the backup battery. However, it is not necessary to fully charge the backup battery for the Terminal to work.  Monitor voltage level (see 3.5 Power) 1.1.3 CAUTION OF LOW BATTERY CHARGE The battery pack is the only power source for the Terminal to work. It also charges the backup battery on the main board so that the data stored in SRAM can be retained properly. Therefore, when the main battery charge goes low, you need to replace the battery pack with a charged one or charge it as soon as possible. Most of all, you should upload important data on a regular basis. Warning: Data loss may occur with SRAM during low battery condition. Always save data before running out of power or keep a fresh battery for replacement.
11 Chapter 1 Using 8200 Terminal 1.2 MEMORY The collected data can be sent back to a host computer immediately over wireless networks, or stored in memory (SRAM) and upload later. The Terminal is equipped with a calendar chip for accurate time/date logging. When the main battery is removed or drained, the backup battery on the main board is to retain the contents of SRAM and maintain the running of real-time clock and calendar for at least 25 days, on condition that the backup battery has already been fully charged. If you want to put away the Terminal for a couple of days, you should be aware that data loss occurs when both the main and backup batteries discharge completely. Therefore, it is necessary to upload data and files before putting away the Terminal! 1.2.1 READ-ONLY MEMORY (ROM) 8 megabytes flash memory for storing core, OS, application programs, font, etc. 1.2.2 RANDOM-ACCESS MEMORY (RAM) Options include 4 or 8 megabytes SRAM for storing data. Its contents will be retained by the backup battery. 1.2.3 SD CARD Secure Digital (SD) card is a flash memory data storage device. High capacity memory card (microSDHC) is supported. Refer to Inserting Battery & Memory Card for how to insert the microSD or microSDHC card. For more details, refer to 1.8 SD Card. Note: (1) When SD card is present, the card icon will appear on the screen and flash while being accessed. (2) For an SD card that has never been used on 8200, a message like “Found New SD Card” will be displayed allowing users to scan the card for memory check. If the action is canceled then, memory check can still be performed via System Menu — 3.8 SD Card Menu.
12 8200 Series Mobile Computer Reference Manual 1.3 KEYPAD The Terminal is equipped with a keypad of 24 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight, like the screen. Refer to 1.4 LCD for screen & backlight settings. Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through programming or via System Menu. Refer to 3.2.6 Key Click. 1.3.1 24-KEY LAYOUT The layout of the 24-key keypad is similar to that of a telephone, which includes alphanumeric, navigation and function keys, as well as assorted characters. Refer to Appendix III — 錯誤! 找不到參照來源。 for color-coded keys. Figure 4: 24-key Layout
13 Chapter 1 Using 8200 Terminal This alphanumeric keypad is set to numeric mode by default. The [Fn α] key serves as a toggle among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes, as well as function mode. Note: It is not necessary to hold down the [Fn α] key. The associated icon will appear on the lower-left corner of the screen in a sequence as shown below. Status Icon Function/Alpha Key Input Mode (none) N/A Numbers A Press [Fn α] one time Upper-case alphabetic a Press [Fn α] two times Lower-case alphabetic F Press [Fn α] three times Function Mode When in alpha mode, it takes turns to show alphabets and number when you keep pressing the same key; each press must not exceed one second. For example, keep pressing the number key [2], it will take turns to show “A”, “B”, “C” or “2” for upper-case, and “a”, “b”, “c” or “2” for lower-case.  When you first press the number key [2], it will produce the letter “A” or “a”.  When you press the number key [2] twice (the time interval must not exceed one second), it will produce the letter “B” or “b”.  When you press the number key [2] three times (the time interval between each press must not exceed one second), it will produce the letter “C” or “c”.  When you press the number key [2] four times (the time interval between each press must not exceed one second), it will produce the number “2”. In order to get the desired character, you will need to press the same key, one to four times (the time interval between each press must not exceed one second). Only when you stop pressing the same key for longer than one second or you press another key, will the system send the real key code to the application program. When in function mode, the [Fn α] key works with a number key. Press the [Fn α] key three times, and its associated icon F will be displayed on the screen. Press the second key, say [5], to complete the key combination and access the function [F5]. Press [Fn α] again and the icon F will go off.
14 8200 Series Mobile Computer Reference Manual Below briefly describes the functions of common keys on the Terminal. SCAN The yellow key is used to work as the ENTER key by default.  When the reader function is enabled, this yellow key is set to trigger the scan engine so that it can read a barcode. ENTER The two keys on each upper side of the SCAN key are user-friendly and convenient for either right-handed or left-handed operator. Normally, it is used for command execution or input confirmation. ESC (Escape) This key is on the left lower side of the SCAN key. Normally, it is used to stop and exit the current operation. Navigation Pad The 4-way navigation pad around the SCAN key is used to move the cursor left, up, down, or right.  While pressing [ ], they can be used to adjust the luminosity and contrast of the screen backlight. Backspace This key is Backspace by default. If this key is being held down for more than one second, a clear code will be sent. Function/Alpha Key This key is a modifier key that requires pressing a second key to get the yellow-coded letter (A~Z) or symbol printed above the second key, or the function (F0~F9) of the second key. Icon Description A This icon appears when you press the [Fn α] key one time, indicating it is set to alphabetic mode for typing upper-case alphabetic letters. a This icon appears when you press the [Fn α] key two times, indicating it is set to alphabetic mode for typing lower-case alphabetic letters. F This icon appears when you press the [Fn α] key three times, indicating it is set to the function mode. Then, press another key ([0] ~ [9]) to get the desired function.  To get the value of another key combination modified by the function key, keep pressing another key ([0] ~ [9]) to produce the result.  To exit the function mode, press [Fn α] again and the icon will go off.
15 Chapter 1 Using 8200 Terminal Backlight Configuration Key This key is used to turn ON/OFF the backlight of the LCD and keypad. Also, while pressing [ ], the navigation keys can be used to adjust the luminosity and contrast of the screen backlight. Key Description [] + [Right] Press these keys at the same time to increase the contrast. [] + [Left] Press these keys at the same time to decrease the contrast. [] + [Up] Press these keys at the same time to increase the luminosity. [] + [Down] Press these keys at the same time to decrease the luminosity. Power Key In order to prevent an accidental press of the POWER key, you need to hold down this key for approximately 1.5 seconds to turn ON/OFF the Terminal. Note: (1) Functionality of keys is application-dependent. The system will send the associated key code to the application program, and it is up to the application program to interpret the key code. (2) When a status icon appears on the screen, it indicates a certain mode is activated and it is not necessary to hold down the modifier key.
16 8200 Series Mobile Computer Reference Manual 1.4 LCD The Terminal comes with a FSTN graphic LCD, 160 by 160 pixels resolutions, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs. Options Font Size (pixels) Characters by lines English font Font size 6×8 (pixels) Font size 8×16 (pixels) 26 characters by 18 lines 20 characters by 9 lines Chinese font Font size 12×12 (pixels) Font size 16×16 (pixels) 13 characters by 12 lines 10 characters by 9 lines Other language fonts, company logo… Programmable Note: The bottom line (ICON_ZONE) is reserved to display status icons, such as the battery icon. 1.4.1 ADJUSTING THE BACKLIGHT The backlight of screen and keypad helps ease reading under dim environments. It can be turned on and adjusted decreasingly or increasingly by the following key combinations. Keep pressing the key combination until the luminosity or contrast is decreased or increased to a desired level. Alternatively, the luminosity and contrast can be configured through programming or via System Menu. Refer to 3.2.2 Backlight and 3.2.3 Contrast. Note: Using backlight while on battery power will substantially reduce battery power. We suggest that you dim the backlight while working in a well-lit area or have it set to be automatically turned off when not in use. Key Combination Action [] Toggle ON/OFF the backlight [] + [Up] Turn ON the backlight and increase the luminosity of LCD [] + [Down] Turn ON the backlight and decrease the luminosity of LCD [] + [Right] Turn ON the backlight and increase the contrast of LCD [] + [Left] Turn ON the backlight and decrease the contrast of LCD Note: Hold down the first key, and keep pressing the second key for adjustment.
17 Chapter 1 Using 8200 Terminal 1.5 NOTIFICATIONS 1.5.1 STATUS LED There are two dual-color LED indicators above the screen. Both can be programmed to provide information that helps diagnosing. For example, if you are using AG runtime, you will be informed of the scanning result immediately. LED1 is used for "Good Read" and will become solid green upon reading a barcode successfully.  LED1 is used to provide information on the charging status and barcode decoding.  LED2 is used to provide information on wireless communications. Figure 5: LED Indicators LED1 LED2
18 8200 Series Mobile Computer Reference Manual LED1: Red/Green Red Green User Power ON User definable User definable  Solid green for Good Read by default Power Off, Battery Charging System default  Flashing red: Charging System default  Flashing green: Charging done Charging Error System default  Flashing red and green: Charging error occurs LED2: Blue/Green Blue Green Bluetooth System default  Flashing blue, quickly: Waiting for connection or connecting  Flashing blue, slowly: Connected --- Wi-Fi --- System default  Flashing green, quickly: Waiting for connection or connecting  Flashing green, slowly: Connected 1.5.2 AUDIO The Terminal has a mono or stereo speaker at the bottom, which can be programmed for status feedback. It is used to play sounds for events in the programs, or play audio files such as .WAV files. Its volume can be configured through programming or via System Menu. Refer to 3.2.7 Speaker Volume. In particular, its frequency and duration are software programmable for Good Read in the provided terminal emulation programs. 1.5.3 VIBRATOR The Terminal is integrated with a vibrator, which can be programmed for status feedback. It can be helpful when working in noisy environments. In particular, the vibrator is software programmable for Good Read in the provided terminal emulation programs.
19 Chapter 1 Using 8200 Terminal 1.6 DATA CAPTURE A wide variety of scan engines is available for delivering flexibility to meet different requirements. Depending on the scan engine integrated, the Terminal is capable of scanning barcodes of a number of symbologies that are enabled by default while running the preloaded AG runtime. Refer to 3.3.1 Reader for functional test. If you need to scan barcodes that are encoded in a symbology, which is disabled by default in AG runtime, FORGE Application Generator (ForgeAG.exe) allows configuring symbology settings, as well as reader settings. First, enable the desired symbologies, and then, download the application settings to the Terminal. Note: For details on configuring reader and symbology settings, please refer to the documentation of the software you use. Varying by the scan engine installed, the supported symbologies are listed below.  1D CCD scan engine  1D Laser scan engine  2D scan engine Note: In AG or CipherNet runtime, not all of the symbologies are enabled by default. Instead of running any of them, you can develop your own applications to control the scan engine for data collection. Symbologies Supported (Default Setting: Enable/Disable) CCD/Laser 2D Codabar Enabled Enabled Code 11 Disabled Code 93 Enabled Enabled Composite Code CC-A/B Disabled CC-C Disabled TCIF Linked Code 39 Enabled MSI Disabled Disabled Plessey Disabled Postal Codes Enabled Telepen Disabled Code 128 Code 128 Enabled Enabled GS1-128 (EAN-128) Enabled Enabled ISBT 128 Enabled Enabled Code 2 of 5 Industrial 25 (Discrete 25) Enabled Enabled Interleaved 25 Enabled Enabled Matrix 25 Disabled Disabled
20 8200 Series Mobile Computer Reference Manual Chinese 25 Disabled Coop 25 Disabled Code 3 of 9 Code 39 Enabled Enabled Trioptic Code 39 Disabled Italian Pharmacode (Code 32) Disabled Disabled French Pharmacode Disabled EAN/UPC EAN-8 Enabled Enabled EAN-8 Addon 2 Disabled Disabled EAN-8 Addon 5 Disabled Disabled EAN-13 Enabled Enabled EAN-13 & UPC-A Addon 2 Disabled Disabled EAN-13 & UPC-A Addon 5 Disabled Disabled Bookland EAN (ISBN) Disabled Disabled UPC-E0 Enabled Enabled UPC-E1 Disabled Disabled UPC-E Addon 2 Disabled Disabled UPC-E Addon 5 Disabled Disabled UPC-A Enabled Enabled GS1 DataBar (RSS) GS1 DataBar Omnidirectional (RSS-14) Disabled Enabled GS1 DataBar Truncated Disabled Enabled GS1 DataBar Stacked Disabled Enabled GS1 DataBar Stacked Omnidirectional Disabled Enabled GS1 DataBar Limited (RSS Limited) Disabled Enabled GS1 DataBar Expanded (RSS Expanded) Disabled Enabled GS1 DataBar Expanded Stacked Disabled Enabled 2D Symbologies PDF417 Enabled MicroPDF417 Enabled Data Matrix Enabled Maxicode Enabled QR Code Enabled
21 Chapter 1 Using 8200 Terminal 1.7 CHARGING & COMMUNICATIONS Normally, the Terminal ships with a USB cable for charging and communications.  If you are using USB Virtual COM for the first time, you must install its driver from the CD-ROM. Driver version 5.3 or later is required. Please remove older versions! The virtual COM port will not be assigned until the USB port is in use.  If you are using USB Virtual COM_CDC for the first time, you must install its driver from the CD-ROM. USB CDC driver installer is available in the “Windows” folder, which will copy a vendor-supplied INF file to Windows.  For Standard USB cable, it will release COM port in the following conditions: (i) Detach the cable from the Terminal directly. (ii) The Terminal is turned off. (iii) No application is running on the Terminal, or COM port is shut down. USB Interface Cable Task USB Cable Charging USB direct charging  500 mA: USB icon  100 mA: Highlighted USB icon  0 mA: Disable charging for 8200 5 V charging from the adaptor (Plug icon) Communications USB Virtual COM — If using FORGE Application Generator software, you may use a download utility to receive data on your computer; otherwise, run HyperTerminal.exe to receive data directly. USB HID — Run a text editor on your computer to receive data directly. USB Virtual COM_CDC — If using FORGE Application Generator software, you may use a download utility to receive data on your computer; otherwise, run HyperTerminal.exe to receive data directly.
22 8200 Series Mobile Computer Reference Manual Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. 1.7.1 INTERFACE CABLE OPTIONS For charging via the USB cable, the standard charging current is 500 mA. However, we recommend you to connect the power adaptor to speed up charging the battery.  If you connect the Terminal to a USB hub, the charging current may be insufficient. In that case, change the charging current to 100 mA after connecting the USB cable. It will take a longer time to charge to full. Refer to 3.2.9 USB Charge Current. Universal Power Adaptor Push & release
23 Chapter 1 Using 8200 Terminal Warning: The Terminal is not allowed to function when it is solely on USB power and without a battery loaded. It will display a warning message “Battery Missing” along with an audible alert. In that case, you should install the battery before restarting. Figure 6: Using USB/RS-232 cable
24 8200 Series Mobile Computer Reference Manual 1.8 SD CARD SD card can be accessed directly by using the provided functions in user application. Yet, when 8200 is equipped with SD card and connected to your computer via the USB cable, it can be treated as a removable disk (USB mass storage device) as long as it is configured properly through programming or via System Menu | 8. Next Page | 1. SD Card Menu | 1. Run As USB Disk. Refer to 3.8 SD Card Menu. Note: While running BASIC application, the size of DAT files on SD card can be calibrated. Go to System Menu | 8. Next Page | 1. SD Card Menu | 2. Access SD Card | 4. Check File Size to refresh the size of “A:\BASICRUN\TXACTn.DAT” (n=1~6). 1.8.1 FILE SYSTEM For 8200 Series, it supports FAT12/FAT16/FAT32 and allows formatting the card through C programming or via System Menu | 8. Next Page | 1. SD Card Menu | 2. Access SD Card. Based on the capacity of the card, it will automatically decide the FAT format: Card Capacity FAT Format Sectors per Cluster ≦ 32 MB FAT12 32 ≦ 1 GB FAT16 32 ≦ 2 GB FAT16 64 ≦ 8 GB FAT32 8 1.8.2 DIRECTORY Unlike the file system on SRAM, the file system on SD card supports hierarchical tree directory structure and allows creating sub-directories. Several directories are reserved for particular use. Reserved Directory Related Application or Function Remark \Program  System Menu | Load Program  Program Manager | Download  Program Manager | Activate  Kernel Menu | Kernel Update  UPDATE_BASIC() Store programs to this folder so that you can download them to 8200:  C program — *.SHX  BASIC program — *.INI and *.SYN \BasicRun BASIC Runtime Store DAT and DBF files that are created and accessed in BASIC runtime to this folder. Their permanent filenames are as follows:
25 Chapter 1 Using 8200 Terminal DAT Filename DAT file #1 TXACT1.DAT DAT file #2 TXACT2.DAT DAT file #3 TXACT3.DAT DAT file #4 TXACT4.DAT DAT file #5 TXACT5.DAT DAT file #6 TXACT6.DAT DBF Filename DBF file #1 Record file F1.DB0 System Default Index F1.DB1 Index file #1 F1.DB2 Index file #2 F1.DB3 Index file #3 F1.DB4 DBF file #2 Record file F2.DB0 System Default Index F2.DB1 Index file #1 F2.DB2 Index file #2 F2.DB3 Index file #3 F2.DB4 DBF file #3 Record file F3.DB0 System Default Index F3.DB1 Index file #1 F3.DB2 Index file #2 F3.DB3 Index file #3 F3.DB4 DBF file #4 Record file F4.DB0 System Default Index F4.DB1 Index file #1 F4.DB2 Index file #2 F4.DB3 Index file #3 F4.DB4 DBF file #5 Record file F5.DB0 System Default Index F5.DB1 Index file #1 F5.DB2 Index file #2 F5.DB3 Index file #3 F5.DB4
26 8200 Series Mobile Computer Reference Manual \AG\DBF \AG\DAT \AG\EXPORT \AG\IMPORT Application Generator (a.k.a. AG) Store DAT, DBF, and Lookup files that are created and/or accessed in Application Generator to this folder. 1.8.3 FILE NAME A file name must follow 8.3 format (= short filenames) — at most 8 characters for filename, and at most three characters for filename extension. The following characters are unacceptable: “ * + , : ; < = > ? | [ ]  On 8200 Series, it can only display a filename of 1 ~ 8 characters (the null character not included), and filename extension will be displayed if provided. If a file name specified is longer than eight characters, it will be truncated to eight characters.  Long filenames, at most 255 characters, are allowed when using 8200 equipped with SD card as a mass storage device. For example, you may have a filename “123456789.txt” created from your computer. However, when the same file is directly accessed on 8200, the filename will be truncated to “123456~1.txt”.  If a file name is specified other in ASCII characters, in order for 8200 to display it correctly, you may need to download a matching font file to 8200 first.  The file name is not case-sensitive.
27 This chapter mainly describes the software inside the Terminal. It consists of three modules — Kernel, System, and Application; each has a function menu. When a menu is displayed, you may select an item by either of the following ways:  Press the arrow keys [Up] and [Down] to move the highlight bar.  Press the number key that corresponds to the item number.  Follow the on-screen instructions to change a specific setting, or press [ESC] to return to a previous page or menu. On each screen, the bottom line displays status icons, such as:  The 4-bar battery icon indicates the current power status.  The status icon of input mode or function mode is controlled by the [Fn α] key. Chapter 2 LEARNING SOFTWARE ARCHITECTURE
28 8200 Series Mobile Computer Reference Manual IN THIS CHAPTER 2.1 Application Module ..................................................... 29 2.2 System Configuration & Core ....................................... 30 Figure 7: Software Architecture
29 Chapter 2 Learning Software Architecture 2.1 APPLICATION MODULE The Terminal ships with software package on the CD-ROM. It includes FORGE Application Generator (batch and WLAN versions), MIRROR Emulator (VT and 5250 versions), download utilities, etc. 2.1.1 FORGE APPLICATION GENERATOR (AG) For easy development of applications, the Terminal is preloaded with AG runtime. When you turn on the Terminal, it displays the Main Menu of AG application, as shown below. Batch AG WLAN AG Note: Batch AG supports automatically uploading data to a host computer when the upload interface is properly configured. Once the Terminal is connected via the RS-232 or USB Virtual COM cable, there will be a moving hourglass icon displayed on the upper-right corner of the screen, indicating the Terminal is ready for auto upload. Before using the Terminal to collect data, you need to configure the application with the companion tool on your computer. This time-saving development tool helps create application templates on your computer. For details on the AG application, please refer to separate user manual. Application Generator AG Runtime Companion Tool on PC End Batch AG U8200.SHX ForgeAG.exe WLAN AG WU8200.SHX AG8200WLAN.exe Note: FORGE Application Generator (AG) software package includes (1) a companion tool for quickly developing your application — Batch or WLAN AG; (2) several download utilities to make it versatile in use.
30 8200 Series Mobile Computer Reference Manual 2.1.2 MIRROR EMULATOR (CIPHERNET) The Terminal supports VT100/220 and IBM 5250 terminal emulation for accessing a backend database. Instead of using FORGE Application Generator, you may download the terminal emulation program, i.e. CipherNet Runtime, to the Terminal. Refer to 3.6 Load Program. Then, run individual companion tool on your computer. For details on the MIRROR Emulator application, please refer to separate user manuals. Terminal Emulation CipherNet Runtime Companion Tool on PC End VT100/220 82xx-VT.SHX CipherNet-VT.exe IBM 5250 82xx-5250.SHX CipherNet-5250.exe 2.1.3 USER PROGRAM You may need to develop your own application program. For developing custom applications, CipherLab provides BASIC and C compilers through licensing. For detailed information, please contact your sales representative. 2.2 SYSTEM CONFIGURATION & CORE
31 Chapter 2 Learning Software Architecture For managing system configurations and multiple programs, each Terminal comes with System Menu, Program Manager, and Kernel Menu. Refer to the following chapters on how to configure the 8200 Series Terminal, regarding system configurations and program download. 2.2.1 SYSTEM MENU System Menu is bundled with BASIC Runtime or user programs that are written in “C”. It is provided for system configuration, functionality testing, downloading font file and program. 2.2.2 KERNEL Kernel is the innermost core of the OS. It provides services for updating the kernel and bootloader, and repairing the system. 2.2.3 PROGRAM MANAGER Program Manager is part of the kernel. You may download as many as seven application programs.
32 8200 Series Mobile Computer Reference Manual
33 System Menu is generated by a powerful utility, which offers an interface for engineers (programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics. This menu is designed for engineering tests and maintenance ONLY. For this reason, it provides password protection to prevent unauthorized users from accidentally changing system settings. Warning! System Menu is NOT for the use of any end users. The system password helps ensure system safety and integrity. How to access System Menu? 5) Turn off the Terminal. 6) Press [7] + [9] + [Power]. Chapter 3 SYSTEM MENU
34 8200 Series Mobile Computer Reference Manual IN THIS CHAPTER 3.1 Information ............................................................... 34 3.2 Settings ................................................................... 36 3.3 Tests ....................................................................... 40 3.4 Memory .................................................................... 42 3.5 Power ...................................................................... 43 3.6 Load Program ............................................................ 44 3.7 DoFTP Menu .............................................................. 47 3.8 SD Card Menu ........................................................... 49 錯誤! 找不到參照來源。 .......................... 錯誤! 尚未定義書籤。 3.11 Bluetooth Menu ....................................................... 51 3.12 Wi-Fi Menu .............................................................. 60 3.1 INFORMATION Here provides important system information to help diagnose the system. System Menu | 1. Information H/W Hardware version S/N A serial number assigned to the Terminal M/D Manufacturing date KNL Kernel version LIB BSC C library version BASIC Run-time version, if a BASIC application is downloaded USR Application program version DEV 4-digit code for optional hardware configurations  For example, 2800 indicates the Terminal is equipped with Laser scan engine and combo module for wireless connectivity (Bluetooth + 802.11b/g/n).
35 Chapter 3 System Menu 3.1.1 UNDERSTANDING DEVICE CODE Device Code Modular Component Types 1st digit Reader module 0= none 1= CCD scan engine 2= Laser scan engine 3= 2D scan engine 2nd digit Wireless module 0= none 5= Bluetooth only 8= Bluetooth + 802.11b/g/n (8200) (8260) (8231) 3rd digit Reserved 0 4th digit Reserved 0
36 8200 Series Mobile Computer Reference Manual 3.2 SETTINGS You can change the default settings here. System Settings Default Values Clock Current time Backlight 20 seconds at level 2, backlight shade enabled Contrast Level 4 Auto Off 10 minutes Power On Options Program Resume Key Click Tone 2 Speaker Volume High volume level USB VCOM No. Fixed USB Charge Current 500 mA System Password Open access Font System font Default Set (=Reset to Default) Load factory settings Reset Reader Restore default reader settings Upgrade Reader FW Upgrade 2D reader firmware (For maintenance use only) 3.2.1 CLOCK Set date and time for Real Time Clock. Enter two digits for the year, e.g. 04 for 2004. 3.2.2 BACKLIGHT Set the backlight duration for the keypad and LCD.  Enter a value between 0 and 9999 (second).  Press the arrow keys [Up] and [Down] to adjust the backlight level (4 levels).  Press the [Left] key to adjust the shade effect.
37 Chapter 3 System Menu 3.2.3 CONTRAST Set the contrast level for the LCD.  Press the arrow keys [Up] and [Down] to adjust the contrast level. 3.2.4 AUTO OFF The Terminal will be turned off automatically when no operation is taking place during a specified period of time. Enter a value between 0 and 999 (minute). Note: To disable this function, enter 0. 3.2.5 POWER ON (& WAKEUP EVENT) OPTIONS Set the startup screen once the Terminal is turned on, and specify which events will wake up the Terminal: Power On Options Press the arrow keys [Up] and [Down] to select “Program Resume” or “Program Restart”, and then press [ENTER].  Program Resume: When selected, the Terminal will start from the last session of program before it is turned off.  Program Restart: When selected, the Terminal will start from the first session of the program. WakeUp Events The specified events can wake up the Terminal when the conditions are met. Press the arrow keys [Up] and [Down] to select a specific event, and press [ENTER] to determine when it is treated as a wake-up event or not.  PwrKey: If yes, it will wake up the Terminal upon pressing the Power key.  USB: If yes, it will wake up the Terminal upon connecting the USB cable.  Charged: If yes, it will wake up the Terminal upon completion of charging.  Alarm: If yes, it will wake up the Terminal upon the alarm time is up. Alarm can be set up through programming only.
38 8200 Series Mobile Computer Reference Manual 3.2.6 KEY CLICK The system will produce an audible signal when any key on the keypad is pressed. The current value is highlighted. Select a desired tone for the speaker or mute it. 3.2.7 SPEAKER VOLUME Set the speaker volume.  Press the arrow keys [Up] and [Down] to adjust the volume level (3 levels) or mute it. 3.2.8 USB VCOM NO By default, it is set to use one virtual COM port for all (=FIXED), regardless of how many 8200 Terminals are connected to PC when USB Virtual COM is in use. This setting requires you to connect one 8200 at a time, and will facilitate configuring a great amount of 8200 Terminals via the same virtual COM port (for administrators’ or factory use). If necessary, you can have it set to use variable virtual COM port (=Change by Serial Number), which will vary by the serial number of each different 8200.  Press the arrow keys [Up] and [Down] to select between “Fixed” and “Change by Serial Number”. 3.2.9 USB CHARGE CURRENT By default, the USB charging current is set to 500 mA. For direct charging via the USB cable without supplying a power adaptor, the standard charging current is 500 mA. If you connect the Terminal to a USB hub, the charging current may be insufficient. In that case, change the charging current to 100 mA after connecting the USB cable. It will take a longer time to charge to full.  Press the arrow keys [Up] and [Down] to select between “500 mA” and “100 mA”.  To disable charging for 8200, select “0 mA”. Note: (1) USB direct charging, 500 mA: USB icon (2) USB direct charging, 100 mA: Highlighted USB icon (3) 5V charging from the adaptor: Plug icon 3.2.10 FONT Font version information can be viewed here. It displays System Font if there is no custom font file. If a multi-language font file is downloaded, you will be able to select a font from the list.
39 Chapter 3 System Menu 3.2.11 SYSTEM PASSWORD Set a password to control user access to System Menu, Program Manager and Kernel Menu. The password can be up to eight alphanumeric characters. Note: The password is case-sensitive. To disable a previous password, enter blank on the "Input new password" and "Verify password" screens. 3.2.12 DEFAULT SET Reset system settings to the default values, except for the reader settings. 3.2.13 RESET READER Reset reader settings to the default values. 3.2.14 UPGRADE READER FW Upgrade 2D reader firmware if necessary.
40 8200 Series Mobile Computer Reference Manual 3.3 TESTS Here provides functional tests for key parts. 3.3.1 READER Test the reading performance of the scanner. The supported symbologies depend on the scan engine you use. Refer to 1.6 Data Capture for symbologies that are enabled by default. For symbologies that are disabled by default, they must be enabled through programming.  Press [SCAN] to start. To stop and exit the test, press any key. 3.3.2 SPEAKER Test the speaker with different volume levels.  To stop and exit the test, press any key. 3.3.3 LCD & LED Test the LCD display and LED indicators.  To stop and exit the test, press any key. 3.3.4 KEYBOARD Test the rubber keys. Press any key and its corresponding character will be shown on the screen.  To stop and exit the test, press [ESC]. 3.3.5 MEMORY Test the data memory (SRAM), and the results will be shown on the screen.  To stop and exit the test, press [ESC]. Warning! The contents of the data memory (SRAM) will be wiped out after test.
41 Chapter 3 System Menu 3.3.6 ECHO TEST After a physical connection is established properly, run a test utility on your computer and start the test on your Terminal. Select a desired baud rate if necessary.  To stop and exit the test, press [ESC]. Interface Description Test Utility USB This echo test is to verify connectivity via the USB cable between the Terminal and a host computer.  USB VCOM Echo — The Terminal works as a generic USB device. EchoTest.exe for Virtual COM  USB HID — The Terminal works as an input device; select keyboard type and Caps Lock status for running a test. Any text editor for HID  USB VCOM_CDC Echo — The Terminal works as a generic USB device. EchoTest.exe for Virtual COM 3.3.7 VIBRATOR Test the vibrator.  To stop and exit the test, press [ESC].
42 8200 Series Mobile Computer Reference Manual 3.4 MEMORY Here provides information and initialization function of the memory. 3.4.1 SIZE INFORMATION  RAM — onboard SRAM for data memory  Flash — program memory 3.4.2 INITIALIZE Initialize the data memory. Warning! The contents of the data memory (SRAM) will be wiped out after memory initialization.
43 Chapter 3 System Menu 3.5 POWER Here shows current voltage consumption. Main (battery) It shows dynamic status of the battery pack, which is used as the main power source. Backup (battery) It shows dynamic status of the button cell, which is used to retain data in SRAM. Warning! Always examine the battery icon on the device screen so that you will be alerted for a low battery condition.
44 8200 Series Mobile Computer Reference Manual 3.6 LOAD PROGRAM Here you can access the Load Program service provided by the kernel. Because the kernel will take over the job, you will not be able to return to System Menu by pressing [ESC]. After downloading, restart the Terminal to activate the new program. Refer to Appendix I 錯誤! 找不到參照來源。. Note: The Terminal will stay in download mode for approximately 30 seconds. .SHX Program Download one of the following C program files and/or font file: Program File  AG Runtime: U8200.shx (Batch AG) WU8200.shx (WLAN AG)  CipherNet Runtime: 82xx-5250.shx (CipherNet-5250) 82xx-VT.shx (CipherNet-VT)  BASIC RuntimeNote: B8200.shx  User program Font File Refer to the Font Files folder on CD-ROM. If you have downloaded a BASIC Runtime program, the next time you enter the Load Program submenu you will be able to select whether to download a C program (.SHX) or BASIC program (.SYN). Note: (1) “Load Basic” menu is only available after you have downloaded a BASIC Runtime program. (2) In addition to the system font, there can be only one font file downloaded to the Terminal.
45 Chapter 3 System Menu SETTINGS Interface Options Description USB VCOM Connect the USB cable between your computer and the Terminal. Bluetooth Approach the target Bluetooth enabled device. SD Card This option is available only when the memory card is present. USB VCOM_CDC Connect the USB cable between your computer and the Terminal. Baud Rate Available baud rate options: 115200/57600/38400/19200/9600 bps LOAD PROGRAM VIA BLUETOOTH 1) Go to System Menu | 8. Next Page | 5. Bluetooth Menu | 3. Security, and configure the following Bluetooth settings first.  Authentication  PIN code 2) Go to System Menu | 6. Load Program and select Bluetooth. 3) Start the pairing procedure from your computer, for example, click [Pair Device] and/or [Connect Bluetooth Serial Port]. 4) Run the download utility: ProgLoad.exe - Select interface RS-232 for using Bluetooth SPP. - Select COM port properties that match with the serial port settings used on your computer.
46 8200 Series Mobile Computer Reference Manual LOAD PROGRAM VIA SD CARD 1) If you have copied the desired program file(s) to your SD card, go to System Menu | 6. Load Program and select SD Card. You will see a list of all the files under the directory “\Program”, as shown above. 2) Press the arrow keys [Up] and [Down] to select a file. 3) Press [ENTER] to view information of the program file. 4) Press [ENTER] to confirm downloading the program file to the Terminal. Press [ESC] to abort the download task. Press the arrow keys to select a file. Then, press [ENTER] to view information of the program file.
47 Chapter 3 System Menu 3.7 DOFTP MENU This submenu is for the FTP client connection. It will log the Terminal into an FTP server via Wi-Fi for the following tasks.  Execute and/or update the script file “FTP.dat”  Download the program update(s) .SHX Program Download one of the following C program files and/or font file, firmware file: Program File  AG Runtime: U8200.shx (Batch AG) WU8200.shx (WLAN AG)  CipherNet Runtime: 82xx-5250.shx (CipherNet-5250) 82xx-VT.shx (CipherNet-VT)  BASIC Runtime: B8200.shx  User program Font File Refer to the Font Files folder on CD-ROM. Firmware File  Kernel update: K8200.shx  Bootloader update: BL8200.shx Note: (1) When more than one program files of the same type are specified in the script file, only the last program file is used for update. (2) The system will restart itself right after successful update and the downloaded file(s) will then be removed.
48 8200 Series Mobile Computer Reference Manual 3.7.1 LOCAL Depending on the script file “FTP.dat” saved on the Terminal, you may update the script file or download any program update from FTP server, if necessary. SETTING Interface Options Supported Description Wi-Fi Connect the Terminal to an access point. Note: This setting is available only when the Wi-Fi module is present. 3.7.2 MANUAL You may log into an FTP server manually, and follow the script file on the server and update programs. However, this script file will not be kept after execution, nor replace the existing one on the Terminal, if there is any. SETTINGS Server IP Specify the IP address or name of the FTP server. Server Port Specify the remote port number.  By default, TCP port 21 is used on the server for the control connection. Login Name Specify the user name for logging onto FTP server. Login Password Specify the password for logging onto FTP server. Interface Options Supported Description Wi-Fi Connect the Terminal to an access point. Note: This setting is available only when the Wi-Fi module is present.
49 Chapter 3 System Menu 3.8 SD CARD MENU This submenu is for using the Terminal equipped with SD card as a removable disk, as well as for directly accessing files on SD card. Note: When SD card is present, the card icon will appear flashing while being accessed. If the Terminal is preloaded with Batch AG runtime, it will automatically create two working directories “\AG\IMPORT” and “\AG\EXPORT” on SD card. 3.8.1 RUN AS USB DISK When the Terminal is equipped with SD card and connected to your computer via the USB cable, it can be treated as a removable disk (USB mass storage device) as long as it is configured properly through programming or via selecting [Run as USB Disk]. Note: The SD card must be properly configured through programming or user menu before use. 3.8.2 ACCESS SD CARD Edit the file system or format the SD card. Edit Files View and edit the file system on SD card. Format If the file system is not desired any more, you may format the SD card.  If the capacity is 32 MB or under, the file system will be FAT12.  If the capacity is 32 MB~2 GB, the file system will be FAT16.  If the capacity is larger than 2 GB, the file system will be FAT32. Warning! The contents on SD card will be wiped out after formatting.
50 8200 Series Mobile Computer Reference Manual Check Memory For an SD card that has never been used on 8200, a message like “Found New SD Card” will be displayed allowing users to scan the card for memory check. If the action is canceled then, memory check can still be performed here. Check File Size You may calibrate the size of DAT files on SD card while running BASIC application, and it will refresh the size of “A:\BASICRUN\TXACTn.DAT” (n=1~6). Note: “Check File Size” is only available after you have downloaded the BASIC Runtime.
51 Chapter 3 System Menu 3.11 BLUETOOTH MENU This submenu is for the Terminal, with built-in Bluetooth module, to work with other Bluetooth enabled devices. You must configure these parameters correctly. Bluetooth Settings Default Value HID, SPP, FTP Client DUN Connect Setting Items Need to Be Checked Local Name Remote Name Broadcast Me Power Saving BT-GPRS AP Name DHCP Local IP Address Model no. + Serial no. --- Enable Enable --- Enable 0.0.0.0 v --- v v --- --- --- v --- v v (v)Note (v)Note (v)Note Security Authentication PIN Code Disable --- v v v v Note: BT-GPRS AP Name, DHCP and local IP Address are required for DUN-GPRS mode only.
52 8200 Series Mobile Computer Reference Manual 3.11.1 INFORMATION Information of network configuration can be viewed here. Bluetooth Menu | 1. Information LIB Kernel version  All user libraries reside in Kernel; no external libraries are required. MAC MAC address of the Bluetooth module IAM A name given to the Terminal for identification  By default, it is made up of model number and the serial number. (Identical to 2. Connect Set | 1. Local Name) CTY "Normal" means all 79 channels are available for frequency-hopping  There are bandwidth limitations for 2.4 GHz ISM band in some countries. For example, only 23 RF channels are defined instead of 79 RF channels in Japan, Spain and France. DHCP DHCP server in use or not  It will automatically become enabled while connecting to a BT-GPRS AP. IP IP address of the Terminal
53 Chapter 3 System Menu 3.11.2 CONNECT SETTING Set the connection parameters if necessary. Local Name Enter a name for identifying the Terminal.  By default, it is made up of model number and the serial number. Remote Name Leave it empty unless you want to make a specific connection. Broadcast Me Options — Enable or Disable  For initial connection, broadcasting must be enabled so that other Bluetooth devices can discover the Terminal.  For security concerns, you may disable it in future use to hide the Terminal from other Bluetooth devices. Power Saving This refers to the low power consumption mode. Options — Enable or Disable (Only the Sniff mode is supported.) BT-GPRS AP Name For DUN-GPRS mode, enter the AP name for connecting to the content server. DHCP Options - Enable or Disable Local IP Address Enter a new address for the Terminal, if necessary. Note: BT-GPRS AP Name, DHCP and local IP Address are required for DUN-GPRS mode only.
54 8200 Series Mobile Computer Reference Manual 3.11.3 SECURITY Set or modify security parameters. Authentication Options — Enable or Disable PIN Code Define the encryption key values.  Up to 16 characters, using ASCII code. Note: When authentication is enabled without providing a pre-set PIN code, the Terminal supports dynamic input of PIN code during pairing.
55 Chapter 3 System Menu 3.11.4 ECHO TESTS These echo tests are used for verifying connectivity to make sure the Terminal is within coverage. Press [ESC] to stop and exit the test.  SPP: Serial Port Profile It is used for ad hoc networking.  DUN: Dial-Up Networking Profile DUN Modem - It makes use of a Bluetooth modem or mobile phone as a wireless modem. DUN GPRS – It makes use of a mobile phone with GPRS functionality and connects to GPRS AP.  HID: Human Interface Device Profile It is used for the Terminal to work as an input device, i.e. keyboard, for a host computer.  FTP client: File Transfer Protocol Profile (FTP) It is used for the Terminal to connect to a file server for file transfer.
56 8200 Series Mobile Computer Reference Manual SPP Master Set the Terminal as a master device. 1. Pairing with your computer (slave) must be completed first. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “RS-232” for interface. - Use the Bluetooth COM port that has been paired. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. The Terminal will try to connect to PC (slave). SPP Slave Set the Terminal as a slave device. 1. Enable Authentication and set your PIN code on the Terminal. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “RS-232” for interface. - Use the Bluetooth COM port that has been configured as “outgoing”. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. 4. The Terminal will wait for PC (master) to start the connection. 5. Enter the preset PIN code for authentication on your computer. DUN Modem The Terminal will try to connect to a Bluetooth modem or mobile phone. 1. Pairing with your mobile phone must be completed first. Select “DialUp Network” for Target Machine options. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “Modem” for interface. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. 4. The Terminal will connect to your mobile phone that dials up to your computer. HID Test Set the Terminal as an input device. 1. The Terminal will wait for PC to start the connection. It is suggested to disable Authentication on the Terminal. 2. Run a text editor on your computer. 3. Start to input data via the keypad on the Terminal.
57 Chapter 3 System Menu DUN GPRS The Terminal will try to connect to a mobile phone with GPRS functionality. 1. Pairing with your mobile phone must be completed first. Select “DialUp Network” for Target Machine options. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “TCP/IP – Server” for interface. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. 4. Enter the server IP on the Terminal. 5. The Terminal will connect to your mobile phone that dials up a GPRS AP, and finally connect to your computer (server) through the GPRS AP. FTP Client The Terminal (as a client) will try to connect to an FTP server. 1. Pairing with your FTP server must be completed first. Select “FTP Server” for Target Machine options. 2. The Terminal will try to connect to PC (server). 3. Enter the FTP Test submenu for FTP function test.  Change Directory: Change the current working directory.  Get Folder Listing: View a list of all the folder(s) and file(s) of the current working directory.  Download File: Download a file from PC. The filename will be converted to “BTFTP01” for testing.  Upload File: Upload a file (i.e. BTFTP01) to PC.  Disconnect: Disconnect with the FTP server.
58 8200 Series Mobile Computer Reference Manual 3.11.5 PAIRING TEST The pairing procedure is for the creation and exchange of a link key between two Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information. 1) The Terminal will start with making an inquiry so that the system can generate a list of device(s) that has been discovered nearby. 2) Select a desired target device. For the device name, it can only display a maximum length of 11 characters. When the device name is too long, it will be truncated automatically. 3) Select a Bluetooth service from the “Target Machine” menu. To stop and exit the test, press [ESC]. After pairing successfully, the target device will be added to the Frequent Devices list for quick connection in the future. Note: For the initial use of Bluetooth networking, the pairing procedure must be done before the Echo tests.
59 Chapter 3 System Menu 3.11.6 FREQUENT DEVICES Here is a list of devices that the Terminal has been connected to lately. After each successful pairing, the system will update it. This list can show information of one device that provides any of the following services:  Serial Port (SPP)  Dial-Up Networking (DUN)  Human Interface Device (HID)  FTP Server (FTP) For the device name, it can only display a maximum length of 11 characters. When the device name is too long, it will be truncated automatically. Note: To unpair any device, simply delete the device from this list.
60 8200 Series Mobile Computer Reference Manual 3.12 WI-FI MENU This submenu accesses the settings of 802.11b/g/n wireless networking. You must configure these parameters correctly to be able to make the connection. Note: The menu is available only when the Wi-Fi module is present. Wi-Fi Settings Default Value Ad-hoc Infrastructure Network Setting Items Need to Be Checked DHCP SubNet Mask Local IP Address Default Gateway DNS Server Domain Name Enable 255.255.128.0 0.0.0.0 0.0.0.0 0.0.0.0 --- --- v v --- --- --- v v v v v v WLAN Setting Local Name SS ID System Scale Power Saving Preamble Ad-Hoc Fixed BSSID Model no. + Serial no. --- Medium Enable Long Disable 000000000000 v --- --- --- --- v --- v v v v v --- v Security Authentication WEP Menu EAP Menu WPA Menu Open System Disable Disable Disable --- --- --- --- v v v v
61 Chapter 3 System Menu 3.12.1 INFORMATION Information of network configuration can be viewed here. Wi-Fi Menu | 1. Information Lib Kernel version  All user libraries reside in Kernel; no external libraries are required. Ver Firmware version of the Wi-Fi module MAC MAC address of the Wi-Fi module IAM A name given to the Terminal for identification.  By default, it is made up of model number and the serial number. (Identical to 3. WLAN Setting | 1. Local Name) DHCP DHCP server in use or not IP IP address of the Terminal Mask Subnet Mask Gate Default Gateway
62 8200 Series Mobile Computer Reference Manual 3.12.2 NETWORK SETTING Set parameters for IP networking. DHCP Options — Enable or Disable Subnet Mask Enter a new Mask IP, if necessary. Local IP Address Enter a new address for the Terminal, if necessary. Default Gateway Enter a new address for the default Gateway, if necessary. DNS Server Enter a new address for the DNS server, if necessary. Domain Name The domain name of the host is displayed when DHCP server is enabled. Note: Normally, DHCP is enabled and all of the settings can be obtained from the DHCP server.
63 Chapter 3 System Menu 3.12.3 WLAN SETTING Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2) Infrastructure mode: point to multi-point through access points. Set the following parameters. Local Name Enter a name for identifying the Terminal.  By default, it is made up of model number and the serial number. SS ID This refers to Service Set Identifier or AP name, which is used for remote device association.  The Terminal can ONLY communicate with access points that have the same SS ID. Roaming Setting This refers to Access Point Density. System Scale options — [1] Low [2] Medium [3] High [4] Custom –Tx Rate [5] Custom -Rssi  The value you set must match that set for the access point.  “Low / Medium / High” means the Terminal will search for other APs only when data transmission rate drops below “1 / 2 / 5” Mbps individually.  “Custom –Tx Rate” lets you set data rate for the Terminal to search for other APs when data transmission rate drops below the specified value — 802.11b: 1, 2, 5.5, 11 Mbps 802.11g: 1, 2, 5.5, 11 Mbps & 6, 9, 12, 18, 24, 36, 48, 54 Mbps  “Custom –Rssi” lets you set the conditions for the Terminal to search for other APs — RSSI Threshold: options including -50, -55, -60, …, -85, -90 dBm. When the current AP signal strength (RSSI) goes below the specified value, the Terminal starts to search for other APs. RSSI Delta: options including 0, 5, 10, 15, and 20. Compare the signal strength between the current AP and the new one. If the signal differential between them is equal to or higher than the specified value, the Terminal will connect to the new AP. Roaming Period options — 3 ~ 10 seconds
64 8200 Series Mobile Computer Reference Manual Power Saving This refers to the low power consumption mode. Options — Enable or Disable  The value you set must match that set for the access point. Preamble Options — [1] Long [2] Short [3] Both  The value you set must match that set for the access point. Ad-Hoc This refers to peer-to-peer mode, without going through access points. Options — Enable or Disable Fixed BSSID This refers to the use of a specific AP’s MAC address as the fixed Basic Service Set Identifier.  The Terminal can ONLY communicate with this one and only access point. Scan Setting Specify the scan time period and channels. Scan Time options — 60, 70, 80, 90, 100, 110 ms; and Disable or Enable “Double the time” (for example, when scan time is set to 60 with Double the time enabled, the scan time period for each channel will be 120 ms) Scan Channel options — 1 ~ 14 channel (multiple selection)
65 Chapter 3 System Menu 3.12.4 SECURITY Set or modify security parameters.  WEP: Wired Equivalent Privacy  EAP: Extensible Authentication Protocol  WPA: Wi-Fi Protected Access Authentication [1] Open System [0] Share Key  Default authentication type  This requires implementing WEP key. WEP Menu WEP Setting  Enable (For Share Key, it must be enabled!)  Disable (default) WEP Key Length  64 bits  128 bits (default) Default Key WEP KEY1 WEP Key Enter WEP Keys 1 ~ 4 in one of the following input data type:  ASCII (up to 13 characters)  Hexadecimal (up to 26 characters) EAP Menu (for associating to Cisco access points) EAP Setting  Enable  Disable (default) EAP ID Enter a user name (up to 32 characters) EAP Password Enter a password (up to 32 characters) WPA Menu (WPA-PSK) WPA Setting  Enable  Disable (default) WPA2 Setting  Enable  Disable (default) WPA Passphrase Enter a phrase as your password (8 ~ 63 characters)
66 8200 Series Mobile Computer Reference Manual 3.12.5 SCAN DEVICES Select this command to launch the scanning for the Wi-Fi hotspots within range. The Terminal will first produce a scanning screen and then a result screen that displays all the WiFi hotspots discovered whether open or secured. Select an entry on the result screen to see more details about it including the BSSID, BSS Type, and the security framework it applies. The screenshot below details the result screen: Label Description Function CH channel Delivers the channel (frequency range) in use by the network. R rssi Delivers the “Received Signal Strength Indication”. See 3.12.7 Echo Tests to know how signal strength is rated by numbers. S security Delivers the security of the network. A secured network goes with an asterisk sign (*) while an open network doesn’t. The result screen a secured network channel security rssi, the “received signal strength indication” Select an entry to view more details about it.
67 Chapter 3 System Menu 3.12.6 PROFILE Up to 4 profiles can be used to save Wi-Fi connection options.
68 8200 Series Mobile Computer Reference Manual 3.12.7 ECHO TESTS This function is used to measure the coverage of the range, estimate the number of APs and Terminals needed, and determine the topology of deploying APs. Client Mode Set the Terminal as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP. 1. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “TCP/IP – Server” for interface. - Set Action Mode to “Passive”. 2. Start the echo test on both ends. 3. Enter the server IP and port number on the Terminal. Server Mode Set the Terminal as a server. The Terminal will try to connect to an AP. 1. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “TCP/IP – Client” for interface. - Set Action Mode to “Passive”. 2. Start the echo test on both ends. While running echo tests, if WPA setting is enabled for security, the SSID and Passphrase will be processed to generate a pre-share key. Note: If you change the SSID or Passphrase, it will have to re-generate a pre-share key.
69 Chapter 3 System Menu 1) For initial association with an access point, you will see an antenna icon developing on the screen to indicate that the Terminal is processing a pre-share key. 2) After having generated the pre-share key, the Terminal proceeds to establish a connection with an access point, and you will see the whole antenna is flashing. 3) When the Terminal has been connected to the access point successfully, you will see the whole antenna and the indication of wireless signal strength. Note: If you are programming in C or BASIC, be aware that the antenna icon will appear on the device screen after NetInit() or START TCPIP() is called. (WPA must be enabled first!) The changing icon indicates 8200 is processing a pre-share key. Wait for a few seconds. The antenna icon will become ready and flashes to indicate 8200 is connecting to an access point under the same SSID.Once connected, the antenna icon will stop flashing. Next to the icon, the more bars, the stronger the signal.
70 8200 Series Mobile Computer Reference Manual Once the connection of echo test is established, the details will be displayed as illustrated below. SNR (dB) T RSS (-dBm) NF (-dBm) (Signal to Noise ratio) (Transmit Speed) (Received Signal Strength Level) (Noise Floor Level) 0 ~ 10 10 ~ 20 20 ~ 30 30 ~ 40 over 40 Very Poor Poor Fair Good Very Good 1 2 5.5 11 6 9 12 18 24 36 48 54 Mbps Mbps Mbps Mbps Mbps Mbps Mbps Mbps Mbps Mbps Mbps Mbps 0 ~ 60 60 ~ 75 over 75 Strong Moderate Weak 0 ~ 92 92 ~ 98 over 98 Strong Moderate Weak
71 This chapter explains Program Manager and Kernel that manage multiple programs and firmware upgrade. IN THIS CHAPTER 4.1 Program Manager ...................................................... 71 4.2 Kernel ...................................................................... 76 4.1 PROGRAM MANAGER The Terminal supports multiple applications and languages. In the menu of Program Manager, it allows storing up to six programs and has one activated for the current use. If there is no application program exists, Program Manager will be displayed after you turn on the Terminal. Warning! Program Manager is provided for managing programs in an administrative level. How to access Program Manager? 1) Turn off the Terminal. 2) Press [8] + [Power]. Chapter 4 PROGRAM MANAGER & KERNEL
72 8200 Series Mobile Computer Reference Manual 4.1.1 DOWNLOAD Here provides a full list of programs that are currently stored on the Terminal with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is. The length of program name can be up to 12 characters. Program size is in kilobytes. A suffix letter after the memory sector (1 ~ 6) indicates the file type of program.  “b” for BASIC program (.SYN)  “c” for C program (.SHX) The last line starting with a prefix letter “f” is reserved to display the font file (.SHX) in use on the Terminal. Note: For a custom font file (.SHX) or a BASIC program (.SYN), it can only be downloaded via System Menu.
73 Chapter 4 Program Manager & KernelSPARE MEMORY SECTORS (1 ~ 6) Additional program files can be directly downloaded to these sectors. Download a program file to an empty sector: 1. Press the arrow keys [Up] and [Down] to select an empty sector, and then press [ENTER]. 2. Select a desired interface for downloading. 3. Connect the interface cable if required, and wait for a few seconds to establish a connection… 4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu. Download a program file to an occupied sector: If no available sectors, you'll have to replace one program with the new one. 1. Press the arrow keys [Up] and [Down] to select a program that you want to delete, and then press [ENTER]. 2. The program information is displayed on the screen. Press the [Fn α] key to enter the Alpha mode:  Press the capital letter [C] and follow the steps below to download a program file.  Press the capital letter [D] if you simply want to delete the program. 3. Select a desired interface for downloading. 4. Connect the interface cable if required, and wait for a few seconds to establish a connection… 5. To abort the action, press [ESC]. Then press [ESC] again to return to the menu. From the menu, you'll see the program has been deleted but no new program is present (because you have canceled the download action). ACTIVE MEMORY SECTOR (“ACT”) Only the application program, which needs to be activated immediately, can be downloaded to the active memory sector. Download to Memory Sector “ACT”: 1. Press the arrow key [Down] to select the memory sector “ACT” (may be unoccupied), and then press [ENTER]. 2. Select a desired interface for downloading. 3. Connect the interface cable if required, and wait for a few seconds to establish a connection… If the active memory sector has already been occupied by an application program, the newly downloaded program will replace the currently active program and come into effect immediately.
74 8200 Series Mobile Computer Reference Manual 4.1.2 ACTIVATE The list shows the entire spare programs stored on the Terminal. From the list, you can select from the memory sector (1 ~ 6) or SD card. The selected program will be copied to the active memory sector and replace the current one. Note: A font file cannot be activated. TO CLEAR FILE SYSTEM When <New Program Start> screen appears, “Press [ESC] to clear file” means the file system in the SRAM will be cleared out by pressing [ESC]. Then there will be no data (transactions, settings, etc.) stored on the Terminal when the new program comes into effect. TO KEEP FILE SYSTEM To keep the data, simply press any other key.
75 Chapter 4 Program Manager & Kernel4.1.3 UPLOAD You may duplicate one or all of the programs from the Terminal to a host computer or another Terminal. This can be used to clone software on Terminals. Note: To clone all of the programs, the target Terminal cannot have any other program downloaded except the active one; that is, Memory Sectors 1 ~ 6 must be empty! The procedures are similar to that for downloading programs.  If the target is “Terminal”, the interface options “USB Virtual COM”, “SD Card” and “USB Virtual COM_CDC” are unavailable.  If the target is “PC”, the interface option “SD Card” is unavailable. This screen is not available if you select “2.All Programs” from the previous screen.
76 8200 Series Mobile Computer Reference Manual 4.2 KERNEL The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and System Menu fails at the same time, Kernel Menu provides an access to fix the system. Warning! Kernel Menu is NOT for the use of any end users. How to access Kernel Menu? 1) When the last session is in System Menu or Program Manager, simply turn off the Terminal. Otherwise, you must reload the battery pack. 2) Press [1] + [7] + [Power].
77 Chapter 4 Program Manager & Kernel4.2.1 KERNEL INFORMATION Here provides important system information to help diagnose the system. Kernel Menu | 1. Information H/W Hardware version S/N Serial number of the Terminal M/D Manufacturing date BL Bootloader version KNL Kernel version DEV 4-digit code for optional hardware configurations Refer to Understanding Device Code.
78 8200 Series Mobile Computer Reference Manual 4.2.2 KERNEL UPDATE The kernel and bootloader might need to be updated to improve performance or due to other considerations. Refer to Appendix I 錯誤! 找不到參照來源。.  To download a kernel (K8200.shx) or bootloader (BL8200.shx) update, the procedure is the same as that for downloading a program.  Any attempt to download an older version of bootloader will be rejected.  The system will restart itself right after downloading. Warning: Do not turn off the Terminal while downloading a kernel update or re-starting the Terminal. Otherwise, it will crash the kernel forever. Note: The Terminal will stay in download mode for approximately 30 seconds. .SHX Program Download one of the following firmware files: Firmware File  Kernel update: K8200.shx  Bootloader update: BL8200.shx SETTINGS Interface Options Description USB VCOM Connect the USB cable between your computer and the Terminal. Bluetooth Approach the target Bluetooth enabled device. SD Card This option is available only when the memory card is present. USB VCOM_CDC This option is available only when USB Virtual COM_CDC is in use. Baud Rate Available baud rate options: 115200/57600/38400/19200/9600 bps
79 Chapter 4 Program Manager & KernelKERNEL UPDATE VIA BLUETOOTH 1) Go to Kernel Menu | 4. System Menu | 8. Next Page | 5. Bluetooth Menu | 3. Security, and configure the following Bluetooth settings first.  Authentication  PIN code 2) Go to Kernel Menu | 2. Kernel Update and select Bluetooth. 3) Start the pairing procedure from your computer, for example, click [Pair Device] and/or [Connect Bluetooth Serial Port]. 4) Run the download utility: ProgLoad.exe - Select interface RS-232 for using Bluetooth SPP. - Select COM port properties that match with the serial port settings used on your computer. KERNEL UPDATE VIA SD CARD 1) If you have copied the desired program file(s) to your SD card, go to Kernel Menu | 2. Kernel Update and select SD Card. You will see a list of all the files under the directory “\Program”, as shown above. 2) Press the arrow keys [Up] and [Down] to select a file. 3) Press [ENTER] to view information of the program file. 4) Press [ENTER] to confirm downloading the program file to the Terminal. Press [ESC] to abort the download task. Press the arrow keys to select a file. Then, press [ENTER] to view information of the program file.
80 8200 Series Mobile Computer Reference Manual 4.2.3 BURN-IN TEST This tool is provided for manufacturing use. Warning! You should not perform this test. 4.2.4 SYSTEM MENU Refer to System Menu for details. This submenu is the same as System Menu for system configuration.
81 Model Designation 8200 8231 8260 Wireless Communications Bluetooth 2.1+EDR / BLE dual mode, Class 2 − √ − Bluetooth 2.1+EDR, Class 2 − − √ 802.11b/g/n − √ − Readers Barcode Reader  CCD (linear imager)  Standard Laser  2D Imager Electrical Characteristics Main Battery Rechargeable Li-ion battery – 3.7 V, 1200 mAh Working Time Laser, one scan per 5 seconds, without backlight:  124 hours in batch mode  40 hours in Bluetooth mode (8260 in power saving mode)  20 hours in Wi-Fi mode (1 broadcast packet per second) Backup Battery  Rechargeable Lithium button cell – 3.7 V, 1200 mAh  Data retention – at least 25 days Power Adaptor  Input: AC 100~240 V, 50/60 Hz  Output: DC 5 V, 3 A  Operating Temperature: 0 °C to 40 °C Physical Characteristics CPU 32-bit Toshiba CMOS type, 60 MHz Memory  Program memory – 8 MB flash  Data memory – onboard SRAM, options include 4 or 8 MB Display Graphic LCD, 160 x 160 pixels, FSTN with LED backlight programmable  Font size 6x8: 26 characters by 18 lines  Font size 8x16: 20 characters by 9 lines  Font size 12x12: 13 characters by 12 lines  Font size 16x16: 10 characters by 9 lines Keypad 24 rubber keys, LED backlight programmable Indicators Two dual-color LEDs – red/green and blue/green, programmable Vibrator 0.45G, programmable SPECIFICATIONS
82 8200 Series Mobile Computer Reference Manual Audio Integrated with one mono or stereo speaker Expansion Slot microSDHC supported Enclosure Material Rubber & ABS plastic Dimensions CCD: Laser/2D: 136 mm (L) 58 mm (W) 25 mm (H) 136 mm (L) 58 mm (W) 32 mm (H) Weight Approx. 150 g (Laser, battery included) Environmental Characteristics Temperature Operating: Storage: -10 °C to 55 °C -20 °C to 70 °C Humidity Operating: Storage: 10% to 90% non-condensing 5% to 95% non-condensing Impact Resistance 1.2 m, 5 drops per 6 sides Tumble Test 1000 times at 1 meter Splash / Dust Resistance IP 52 Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Programming Development Tools C and BASIC Software & Utilities FORGE Application Generator (AG), AG utilities; MIRROR Emulator (CipherNet) for VT100/220, IBM 5250 emulation; Download utilities, testing tools, etc. Accessories  Pistol Grip  Spare rechargeable battery pack 
83

Navigation menu