CipherLab 9300 Terminal User Manual 9300 Mobile Computer

CipherLab Co., Ltd. Terminal 9300 Mobile Computer

UserManual.wiki >

CipherLab >

9300 User Manual >

User Manual HTML Version

1. User Manual
2. User Manual

User Manual

Windows CE Mobile Compute

9300

Version 0.09

The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided

under a license agreement containing restrictions on use and disclosure and is also

protected by copyright law. Reverse engineering of the software is prohibited.

Due to continued product development this information may change without notice. The

information and intellectual property contained herein is confidential between CIPHERLAB

and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find

any problems in the documentation, please report them to us in writing. CIPHERLAB

does not warrant that this document is error-free.

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photocopying,

recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.

For product consultancy and technical support, please contact your local sales

representative. Also, you may visit our web site for more information.

The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and/or other countries.

Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.

Other product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies and are hereby acknowledged.

The editorial use of these names is for identification as well as to the benefit of the

owners, with no intention of infringement.

CIPHERLAB CO., LTD.

Website: http://www.cipherlab.com

IMPORTANT NOTICES

FOR USA

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FOR CANADA

This digital apparatus does not exceed the Class B limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

"Digital Apparatus," ICES-003 of Industry Canada.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur:

"Appareils Numeriques," NMB-003 edictee par l'Industrie.

FOR HAND-HELD PRODUCT WITH RF FUNCTIONS

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20

cm between the radiator & your body. It only operated in hand-held used.

If you only transfer data to Host by WLAN/Bluetooth, please keep the minimum distance

20 cm between machine & your body.

FOR PRODUCT WITH LASER

Per FDA and IEC standards, the scan engines described in this manual are not given a

laser classification. However, the following precautions should be observed:

CAUTION

This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not

stare into beam.

SAFETY PRECAUTIONS

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

 The maximum level of Specific Absorption Rate (SAR) measured is 0.211 W/kg.

 The use of any batteries or charging devices, which are not originally sold or

manufactured by CipherLab, will void your warranty and may cause damage to

human body or the product itself.

 DO NOT disassemble, incinerate or short circuit the battery.

 DO NOT expose the scanner or the battery to any flammable sources.

 For green-environment issue, it's important that batteries should be recycled in a

proper way.

 Under no circumstances, internal components are self-serviceable.

 The charging and communication cradle uses an AC power adaptor. A socket outlet

shall be installed near the equipment and shall be easily accessible. Make sure there

is stable power supply for the mobile computer or its peripherals to operate properly.

CARE & MAINTENANCE

 This mobile computer is intended for industrial use. The mobile computer is rated IP

54, however, it may do damage to the mobile computer when being exposed to

extreme temperatures or soaked wet.

 When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe

off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.

 For a liquid crystal display (LCD) or touch screen, use a clean, non-abrasive, lint-free

cloth to wipe dust off the screen. DO NOT use any pointed or sharp object to move

against the surface.

 If you want to put away the mobile computer for a period of time, download the

collected data to a host computer, and then take out the battery pack. Store the

mobile computer and battery pack separately.

 When the mobile computer resumes its work, the main and backup batteries will take

a certain time to become fully charged.

 If you shall find the mobile computer malfunctioning, write down the specific scenario

and consult your local sales representative.

RELEASE NOTES

Version Date Notes



1.00  Initial release

0.09 Jun. 16, 2009  First draft

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This device and its antenna(s) must not be co-located or operating in conjunction with any

other antenna or transmitter.

CONTENTS

IMPORTANT NOTICES ................................................................................- 3 -

For USA..............................................................................................- 3 -

For Canada..........................................................................................- 3 -

For Hand-held Product with RF Functions.....................................................- 3 -

For Product with Laser ...........................................................................- 4 -

Safety Precautions.................................................................................- 4 -

Care & Maintenance...............................................................................- 4 -

RELEASE NOTES.......................................................................................- 5 -

INTRODUCTION........................................................................................... 1

Getting Familiarized with 9300 .....................................................................2

Installing the Hand Strap .........................................................................3

Charging the Battery ..............................................................................4

Features.................................................................................................5

Inside the Package ....................................................................................5

Accessories .............................................................................................6

USING 9300 MOBILE COMPUTER...................................................................... 7

1.1 Battery..............................................................................................7

1.1.1 Inserting the Battery .......................................................................7

1.1.2 Charging the Battery .......................................................................9

1.1.3 Understanding the Battery Icons .........................................................9

1.1.4 Power Management....................................................................... 10

1.2 Memory........................................................................................... 11

1.2.1 Caution of Data Loss...................................................................... 11

1.2.2 Inserting the SD Card..................................................................... 11

1.3 Keypad............................................................................................ 12

1.3.1 Keypad Settings ........................................................................... 12

1.3.2 29-key Keypad............................................................................. 13

1.3.3 43-key Keypad............................................................................. 15

1.3.4 Function Key............................................................................... 16

1.3.5 Programmable Keys....................................................................... 16

1.4 Touch Screen .................................................................................... 17

1.4.1 Adjusting the Backlight .................................................................. 17

1.4.2 Re-calibrating the Screen................................................................ 18

1.5 Notifications ..................................................................................... 19

1.5.1 Status LED.................................................................................. 19

1.5.2 Audio........................................................................................ 19

1.5.3 Vibrator..................................................................................... 20

1.6 Data Capture .................................................................................... 20

1.6.1 Barcode & RFID Reader .................................................................. 20

9300 Mobile Compute

Reference Manual

SPECIFICATIONS.........................................................................................21

Platform, Processor & Memory.................................................................... 21

Communications & Data Capture ................................................................. 21

Electrical Characteristics........................................................................... 22

Physical Characteristics ............................................................................ 22

Environmental Characteristics..................................................................... 23

Programming Support............................................................................... 23

Accessories ........................................................................................... 24

SCAN ENGINE SETTINGS ...............................................................................25

Symbologies Supported ............................................................................. 25

RFID Tags Supported ................................................................................ 27

CCD/LASER SCAN ENGINE .............................................................................29

Reader Settings Table .............................................................................. 29

Symbology Settings Table .......................................................................... 30

2D SCAN ENGINE........................................................................................35

Reader Settings Table .............................................................................. 35

Symbology Settings Table .......................................................................... 36

AIM Code ID – Code Characters................................................................. 44

AIM Code ID – Modifier Characters............................................................. 44

INTRODUCTION

9300 Mobile Computer, running Windows CE 6.0 in palm size, is our first product line of

rugged PDA-style Mobile Computer. Light-weight, streamlined and ergonomic, it adds

even more powerful and handy tools to delivering the flexibility in customization.

Specifically designed to work as an industrial PDA, 9300 Mobile Computer provides rich

options of data collection, voice and data communications, long-lasting working hours,

and so on. Its large color transflective TFT display guarantees ease in reading in all

lighting conditions. Integrated with Bluetooth and 802.11b/g technologies, you may

choose to add the GSM/GPRS module to gain greater speeds and optimal mobility.

This manual serves to guide you through how to install, configure, and operate the

mobile computer. The Care & Maintenance section is specifically prepared for those who

are in charge of taking care of the mobile computer.

We recommend you to keep one copy of the manual at hand for quick reference or

maintenance purposes. To avoid any improper disposal or operation, please read the

manual thoroughly before use.

Thank you for choosing CipherLab products!

9300 Mobile Compute

Reference Manual

GETTING FAMILIARIZED WITH 9300

Figure 1: Overview

Introduction

INSTALLING THE HAND STRAP

The hand strap is ideal for one-handed operation, which requires safe and convenient

hold of the mobile computer.

Warning: Always make sure the hand strap is well hooked and screwed to the back

of the mobile computer before use.

When the hand strap is desired, install it to the mobile computer by following these

steps:

1) Place the mobile computer face down on a flat and clean surface.

2) Screw one end of the hand strap to the back of the mobile computer.

3) Insert and hook the other end of the hand strap to the bottom of the mobile

computer.

4) Make sure the hand strap is securely attached to the mobile computer.

5) Adjust the length of the hand strap to suit your handbreadth.

Figure 2: Installing the Hand Strap

9300 Mobile Compute

Reference Manual

CHARGING THE BATTERY

You can use a cradle or charger to charge the Mobile Computer and/or its battery. Below

are the 4-Slot Battery Charger and 4-Slot Charging Cradle for 9300. The 4-Slot Battery

Charger can be mounted on table or wall. Drill two holes (centers spaced 105 millimeters

apart), secure the two supplied screws, and mount the charger by sliding over screws.

Warning: It is recommended that the charging devices be operated at room

temperature (18°C to 25°C) for optimal performance. The charging devices

will not charge the battery when the temperature exceeds 40°C.

1) Seat batteries with contacts facing to back in the 4-Slo Battery Charger (top), or seat

the mobile computers in the 4-Slot Charging Cradle (bottom).

2) Connect the power supply cord to the power receptacle on the charger or cradle.

3) Connect the other end of the power cord to a suitable power outlet.

4) Press the power switch on, and the charger’s LED or the Power LED on the cradle will

be blue.

5) For the 4-Slot Battery Charger, the LED will be red while charging, and will be green

when fully charged.

For the 4-Slot Charging Cradle, the LED on each of the mobile computers will be red

while charging, and will be green when fully charged.

Figure 3: 4-Slot Battery Charger

Introduction

FEATURES

 Ergonomic design - ruggedized yet streamlined, with hand strap for secure hold.

 Built tough to survive drop test and sealed against moisture/dust to industrial

standard IP 64.

 Microsoft Windows CE 6.0 operating system, 624 MHz Marvell PXA310 processor

 512 MB non-volatile NAND flash memory to store OS and software programs

(part of the free space is used as a storage card called DiskOnChip)

 256 MB on-board DDR SDRAM to store and run programs, as well as store program

data

 One SD expansion slot for memory card

 Dual mode support - One scan engine (integrated barcode scanner/imager) plus one

RFID reader

 Ambidextrous side triggers

 Total wireless solution - connectivity includes Bluetooth, 802.11b/g and

GSM/EDGE/GPRS.

 A 2.8" color transflective TFT display delivers excellent visibility in all lighting

conditions.

 Programmable feedback includes buzzer, speaker and vibrator.

 Built-in power tools include Reader Configuration Utility, Backup Utility, etc.

 Terminal Emulation client for VT100/220 and IBM 5250 enables a quick link to any

backend database.

 Application Generator (AG*.exe for desktop PC) enables easy customization of data

collection applications.

 Programming support includes Reader DLL and System APIs.

 Accessories and peripherals include pistol grip, international AC charging cradle, etc.

INSIDE THE PACKAGE

The following items are included in the package. Save the box and packaging material for

future use in case you need to store or ship the mobile computer.

 9300 Mobile Computer

 Rechargeable Li-ion battery pack

 Stylus

 Hand Strap

 Software & Manual CD

Note: For battery charging, you will need to purchase a charging cradle separately.

9300 Mobile Compute

Reference Manual

ACCESSORIES

Rich choices of optional accessories are available for you to enhance the total

performance of the mobile computer.

 Protective Cover

 SD Memory Card

 Spare rechargeable Li-ion battery, standard or high capacity pack

 4-slot Battery Charger

 Charging & Communication Cradle

Chapter 1

USING 9300 MOBILE COMPUTER

This chapter explains the features and usage of 9300 Mobile Computer.

IN THIS CHAPTER

1.1 Battery....................................................................... 7

1.2 Memory.................................................................... 11

1.4 Touch Screen............................................................ 17

1.5 Notifications.............................................................. 19

1.6 Data Capture ............................................................ 20

1.1 BATTERY

 Main Battery

9300 Mobile Computer is powered by a rechargeable 3.7 V/2700 mAh Li-ion battery

pack, and it takes approximately 4 hours to fully charge it. However, the charging

time may vary by working condition. During normal operation, the mobile computer

can work for up to 10 hours.

 Backup Battery

The backup battery on the main board takes charge when the main battery is

removed or drained out. When fully charged, the 3.6 V/15 mAh rechargeable Lithium

button cell helps retain data in SRAM and maintain the system running in suspend

mode for at least 20 hours without the main battery. In the meantime, you have to

replace the main battery as soon as possible.

1.1.1 INSERTING THE BATTERY

When you first receive the package, the rechargeable functionality of the backup battery

is turned off. It is controlled by a DIP switch inside the battery compartment as shown

below.

For shipping and storage purposes, save the mobile computer and the main battery in

separate packages, and adjust the DIP switch to the OFF position (bottom). This will keep

both batteries in good condition for future use.

Note: Any improper handling may reduce the battery life.

1) Remove the hand strap.

2) Hold the mobile computer still. Press the battery cover latch and slide it to unlock the

battery cover.

3) Remove the battery cover.

9300 Mobile Compute

Reference Manual

4) Insert the battery pack into the battery compartment at a proper angle (30°~45°) so

that the metal contacts on the battery are met with the charging contacts inside the

compartment. Make sure that the battery is snugly fit into the compartment.

5) Put the battery cover back onto the mobile computer until it clicks into place.

6) If the battery is charged, the mobile computer turns on.

If the mobile computer does not turn on, charge the battery.

Note: For a new battery, make sure it is fully charged before use. Always prepare a

spare battery pack, especially when you are on the road.

Figure 4: Installing the Main Battery

Specifications

1.1.2 CHARGING THE BATTERY

The main and backup batteries may not be charged to full for shipment. When you first

receive the package, you will need to charge batteries to full before using the mobile

computer.

Note: To charge the batteries to full, it requires approximately 8 hours for the first time.

After the initial charging, it takes only 4 hours to charge the batteries to full.

Because the internal backup battery is constantly charged from the main battery, the

initial charging requires inserting the battery pack to the mobile computer and then

seating the mobile computer in the cradle for charging. This will have both the main and

backup batteries charged at the same time. To charge the backup battery, make sure

that you slide the DIP switch inside the battery compartment to the ON position.

Note: For a new battery, make sure it is fully charged before use. Always prepare a

spare battery pack, especially when you are on the road.

1.1.3 UNDERSTANDING THE BATTERY ICONS

The battery pack is the only power source for the mobile computer to work. It also

charges the backup battery on the main board so that the data stored in SRAM can be

retained properly. Therefore, when the main battery charge goes low, you need to

replace the battery pack with a charged one or charge it as soon as possible. Most of all,

always save data before it is too late; you should backup important data on a regular

basis.

Double-tap a battery icon so that you can quickly access the [Power Properties] dialog

box.

Battery Status Icons Description

Battery charge remaining in the main battery –

The more bars, the more

power in the main battery.

Main battery is ready for charging.

Main battery charge becomes low and needs charging.

Main battery charge becomes very low and needs charging immediately.

Warning: Data loss may occur with SRAM during low battery condition. Always save

data before running out of power or keep a fresh battery for replacement.

9300 Mobile Compute

Reference Manual

1.1.4 POWER MANAGEMENT

For any portable device, power management is a critical issue especially when you are on

the road. Below are some tips to help you save battery power.

Warning: Using backlight, wireless connectivity, and peripherals while on battery

power will substantially reduce battery power.

 To speed up charging the mobile computer, turn off the mobile computer and seat it

in the cradle.

 Bring a second battery pack on the road.

 Stop wireless connectivity, Bluetooth, 802.11b/g or GSM/GPRS that is not in use.

 Go to Start > Settings > Control Panel and double-tap the Display icon. Refer to

1.4.1 Adjusting the Backlight.

 Go to Start > Settings > Control Panel and double-tap the Power icon. (below)

1. In the Battery tab (left below), you can always monitor the charging status.

2. Tap the Schemes tab. (right above)

3. Select the desired power scheme and options for suspending operation when not

in use. The system can be set to three different states to conserve power:

 User Idle state

 System Idle state

 Suspend state

The time choices represent the amount of time that must pass before the system

will switch to the next power conservation state.

Specifications

1.2 MEMORY

 Read-only Memory (ROM)

512 megabytes flash memory for storing OS (Windows CE 6.0) and custom

application programs. Yet a portion of the memory is referred to as DiskOnChip,

which can store data and programs that you wish to retain even after hardware reset.

 Random-access Memory (RAM)

256 megabytes SDRAM for storing and running programs, as well as storing program

data. Its contents will be retained by the backup battery.

 Expansion Slot

The mobile computer is equipped with one SD card slot, which is user accessible. You

may upgrade memory by inserting an optional SD memory card.

1.2.1 CAUTION OF DATA LOSS

When the main battery is removed or drained, the backup battery on the main board is

to retain the contents of SRAM and maintain the OS in suspend mode for at least 20

hours, on condition that the backup battery has already been fully charged.

If you want to put away the mobile computer for a couple of days, you should be aware

that data loss occurs when both the main and backup batteries discharge completely.

Therefore, it is necessary to backup data and files before putting away the mobile

computer!

1.2.2 INSERTING THE SD CARD

If you wish to expand memory, follow these steps to insert a memory card into the SD

card slot:

1) Press for the mobile computer to enter suspend mode.

2) Place the mobile computer face down on a flat and clean surface.

3) Remove the side plate by unscrewing the two screws (on the right side when you

place the mobile computer face down) as shown below.

4) Insert the SD card properly.

9300 Mobile Compute

Reference Manual

5) Replace the side plate and tighten the screws.

Warning: Make sure the mobile computer is set to Suspend mode; otherwise, it may

cause damage to the mobile computer.

Figure 5: Inserting the SD Card

REMOVING THE SD CARD

If you wish to remove the SD card, simply push the card after removing the side plate.

The SD card will be rejected automatically.

1.3 KEYPAD

Silicon rubber has been chosen for their durability and prompt feedback.

Note: Functionality of keys is application-dependent.

1.3.1 KEYPAD SETTINGS

 Press [FN] first, and then [0].

The LED backlight of keypad is turned off by default. It can be toggled ON/OFF by the

key combination: [FN] + [0]. It is suggested to turn on the keypad backlight while

working in a dark area; however, using backlight while on battery power will

substantially reduce battery power.

 Go to Start > Settings > Control Panel and double-tap the Keyboard icon.

The Character Repeat functionality is enabled by default. You may cancel the check

box to disable it. When enabled, tap, hold, and drag the slider for a desired Repeat

Delay and Repeat Rate.

Specifications

1.3.2 29-KEY KEYPAD

The 29-key keypad includes alphanumeric, navigation, function keys, and so on. This

keypad is set to numeric mode by default.

Screen + 29-key

Figure 6: 29-key Layout

9300 Mobile Compute

Reference Manual

ALPHA KEY

This alphanumeric keypad is set to numeric mode by default. The Alpha key serves as a toggle

among numeric, alpha (lower-case alphabetic), and ALPHA (upper-case alphabetic) input modes.

Note: It is not necessary to hold down the [Alpha] key.

The alpha icon will appear on the status bar in a sequence as shown below.

Status Icon Alpha Key Input Mode

N/A Numbers

Press one time Small letters

Press two times Capital letters

Note: If you are using the software keypad via SIP, tap CAP (Caps Lock) to toggle

between upper case and lower case alphabetic modes.

Specifications

1.3.3 43-KEY KEYPAD

The 43-key keypad includes numeric, alphabetic, function and other modifier keys, as

well as keys for navigation and assorted characters.

VGA Screen + 43-key

Figure 7: 43-key Layout

9300 Mobile Compute

Reference Manual

1.3.4 FUNCTION KEY

The [FN] (function) key serves as a modifier key, and the functionality of each key

combination is application-dependent.

1) To enable this modifier key, press [FN] on the keypad. A circular icon of the letter "F"

will appear on the status bar. This modifier key is hold down as long as the icon is

displayed.

2) Now press another key to get the value of key combination (say, press [1] to get the

value of F1). The icon will go off now.

3) To get the value of another key combination modified by the [FN] key, repeat the

above steps.

4) To abort the key modification, press [FN] again, and the icon will go off.

Note: It is not necessary to hold down the [FN] key.

Below is a list of the factory setting for a variety of key combinations.

Key Combination Action

[FN], Move text up one screenful (Page Up)

[FN], Move text down one screenful (Page Down)

[FN], Move to the beginning of screen or document (Home)

[FN], Move to the end of screen or document (End)

[FN], [0] Toggle ON/OFF the backlight of keypad only

([FN], [*@-] for 28-key)

([FN], [.$] for 59-key)

urn ON the backlight of LCD and decrease its

luminosity

([FN], [.#$] for 28-key)

([FN], [- ;] for 59-key)

Turn ON the backlight of LCD and increase its

luminosity

Note: Press the [FN] key first, and then press the second key for a specific function.

1.3.5 PROGRAMMABLE KEYS

Depending on the keypad layout, a number of keys are user-definable, such as the

programmable keys. They can be re-defined as another key or to serve as a shortcut key

for launching a specific program. Refer to the Button Assignment Utility.

Specifications

Programmable Keys Other User-Definable Keys

P1, P2 (28-key) SCAN key and four side triggers on each side of the touch screen

P1, P2, P3 and P4 (59-key) Four side triggers on each side of the touch screen

1.4 TOUCH SCREEN

The mobile computer comes with a 2.8" TFT graphic LCD, 320 by 240 pixels resolution

(QVGA). The LED backlight of screen, which helps ease reading under dim environments,

can be controlled manually and automatically.

Warning: Using backlight while on battery power will substantially reduce battery

power. It is suggested to dim the backlight while working in a well-lit area

or automatically turn off the mobile computer when not in use.

1.4.1 ADJUSTING THE BACKLIGHT

The LED backlight of the screen can be turned on and adjusted decreasingly or

increasingly by the following key combinations. Keep pressing the key combination until

the luminosity is decreased or increased to a desired level.

Key Combination Action

, ([Backlight], [DOWN] for 29-key)

, ([[Backlight], [DOWN] for 43-key)

urn ON the backlight of LCD and decrease its

luminosity

, ([[Backlight], [UP] for 29-key)

, ([[Backlight], [UP] for 43-key)

urn ON the backlight of LCD and increase its

luminosity

Note: Press the [FN] key first, and then press the second key for adjustment.

 Go to Start > Settings > Control Panel and double-tap the Display icon.

1. Tap the Backlight tab. (left below)

9300 Mobile Compute

Reference Manual

2. Select one or both of the check boxes to automatically turn off the LCD backlight

when using batteries or external power. From the appropriate list, select the

amount of time the device should be idle before the backlight is turned off.

3. Tap the [Advanced] button.

4. In the Settings tab (right above), you can select the luminosity of backlight when

it is set to be automatically turned on by pressing any key or tapping the screen.

Tap, hold, and drag the slider for AC and battery powered respectively. For more

luminosity, move the slider to the right.

1.4.2 RE-CALIBRATING THE SCREEN

This LCD is also a touch screen that can be calibrated through screen alignment.

 Go to Start > Settings > Control Panel and double-tap the Stylus icon.

Tap the Calibration tab, and then tap the [Recalibrate] button.

Specifications

Warning: DO NOT use any pointed or sharp objects to move against the surface of

the screen.

1.5 NOTIFICATIONS

1.5.1 STATUS LED

The tri-color LED on top is used to provide information on the charging status or wireless

power status. The green LED is also used for "Good Read" while collecting data.

Tasks Green LED Red LED Blue

Charging 9300 --- On ---

Charging done On --- ---

Good Read On --- ---

Bluetooth enabled --- --- On

1.5.2 AUDIO

 Buzzer

The mobile computer has a buzzer on the back. It can be programmed for status

feedback. Its frequency and duration are software programmable.

 Speaker

The mobile computer is integrated with a mono speaker, which can be used for

playing sounds applied to events in Windows and programs, as well as playing audio

files such as .WAV files. In addition, it can be programmed for status feedback.

9300 Mobile Compute

Reference Manual

 Headset

A headset jack is provided, which is a 2.5 mm DIA stereo earphone jack with

microphone input. Bluetooth headset is also supported.

1.5.3 VIBRATOR

The mobile computer is integrated with a vibrator, which is software programmable for

feedback. This can be helpful when working in noisy environments.

1.6 DATA CAPTURE

1.6.1 BARCODE & RFID READER

A wide variety of scan engines is available for delivering flexibility to meet different

requirements. Depending on the scan engine integrated, the mobile computer is capable

of scanning barcodes of a number of symbologies that are enabled by default while

running 93ReaderConfig.exe. If you need to scan barcodes that are encoded in a

different symbology, enable the symbology first. Refer to Appendixes for details on scan

engine settings.

 Appendix I - Scan Engine Settings lists the symbologies and RFID tags supported.

 Appendix II - CCD/Laser Scan Engine provides information on the reader settings as

well as symbology settings for the CCD or Laser scan engine.

 Appendix III - 2D Scan Engine provides information on the reader settings as well as

symbology settings for the 2D scan engine.

Note: The mobile computer allows the co-existence of one integrated scan engine and

the RFID reader.

Specifications

SPECIFICATIONS

PLATFORM, PROCESSOR & MEMORY

Operating System

Microsoft Windows CE 6.0

CPU

Marvell PXA310 at 624 MHz

Memory

ROM 512 MB non-volatile NAND flash memory

RAM 256 MB on-board DDR SDRAM memory

Expansion Slot One SD card slot for inserting memory card, optional

COMMUNICATIONS & DATA CAPTURE

Communications

USB 1.1 Specification

Host port (type-A) / Device port (type-B)

USB via Cradle

USB Client 2.0

WPAN Built-in module for Bluetooth Class 2 connectivity

WLAN Built-in module for 802.11b/g networking

RS232 Support baud rate 9600, 19200, 38400, 57600, 115200, 230k, 640k, and

921k.

Data & Image Capture

Barcode Reader Ordering options include

 1D SE 955 Standard Laser

 2D Imager

9300 Mobile Compute

Reference Manual

ELECTRICAL CHARACTERISTICS

Batteries

Main Battery Pack Rechargeable Li-ion battery – 3.7 V, 2700 mAh

Backup Battery Rechargeable Lithium battery – 3.6 V, 15 mAh

Data retention for at least 20 hours

Power Adapter

Input AC 100~240 V, 50/60 Hz

Output DC 5 V, 3 A (Charging & Comm. Cradle)

Working Time (Laser, one scan per 5 seconds)

Batch Mode with backlight 10 hours

Wi-Fi Mode with backlight 8 hours

PHYSICAL CHARACTERISTICS

Color Touch Screen Display

Display 2.8” Transflective TFT-LCD, 65536 colors

Resolution QVGA (320 × 240 pixels)

Keypad

Layout 29 keys for alphanumeric layout

 Ordering Option – 43-key layout

Backlight White LED backlight for display and keypad

Notifications

Status LED Two dual color LED – Red / Green and Green / Blue

Audio Integrated with one mono speaker and buzzer

Headset jack –

2.5 mm DIA stereo earphone jack with

microphone input

 Bluetooth headset supported

Vibrator 0.45G

Enclosures

Materials Plastic and metal

Dimensions 170 mm (L) 70 mm (W) 40 mm (H)

Weight Approx. 350 g (configuration-dependent)

Specifications

ENVIRONMENTAL CHARACTERISTICS

Temperature

Operating -10 °C to 50 °C

Storage -20 °C to 60 °C

Humidity

Operating 10% to 90%, non-condensing

Storage 5% to 95%, non-condensing

Resistance

Impact Resistance 1.5 m, 5 drops per 6 sides

Tumble Test 100 cm, 1000 drops

Splash/Dust Resistance IP 54

Electrostatic Discharge ± 15 kV air discharge, ± 8 kV direct discharge

Regulations

EMC Regulations FCC, IC, CE, C-Tick, MIC, BSMI, NCC, TELEC, SRMC

PROGRAMMING SUPPORT

Development Environment & Tools

Integrated Development

Environment Visual Studio 2005

Visual Studio .NET 2003

eMbedded Visual C++ 4.0 SP4

9300 SDK or Windows CE 6.0 Standard SDK Software Development Kit

System API (static and DLL) for system configuration

ReaderDLL for reader configuration

Software & Utilities

Reader Configuration Utility

Terminal Emulation for VT100/220 or IBM 5250

Application Generator

STREAM Wireless Studio

Web Browser

Third-party software –

 Wavelink Avalanche Enabler & Telnet Client

 MCL Collection - MCL Client

9300 Mobile Compute

Reference Manual

ACCESSORIES

Accessory Options

SD Memory Card

Protective Cover

Spare rechargeable battery pack, standard or high capacity pack

4-Slot Battery Charger

Charging & Communication Cradle

Appendix I

SCAN ENGINE SETTINGS

The Reader Configuration Utility (93ReaderConfig.exe) allows configuring the

following reader types, depending on the module equipped on your mobile computer:

 1D CCD scan engine

 1D Laser scan engine

 2D scan engine

 RFID reader

Options of different reader combination are allowed, such as 1D+RFID and 2D+RFID. For

each combination, both readers can be initialized and ready for scanning at the same

time (dual mode operation). For example, if you press the [SCAN] button while running

the 93ReaderConfig utility on the mobile computer, it will read a barcode in position or an

RFID tag in proximity depending on which one comes first.

Note: (1) You cannot have 1D+2D scan engines installed on the mobile computer

because they are both barcode readers!

(2) You can run only one utility or application at a time to control the reader(s).

For example, while running 93ReaderConfig.exe, you should not run Application

Generator, STREAM Wireless Studio, MIRROR Browser, or any other application

that uses ReaderDLL.

SYMBOLOGIES SUPPORTED

Varying by the scan engine installed, the supported symbologies or tag types are listed

below. For details on configuring associated settings, please refer to each Appendix

separately.

CCD, Laser 2D

Codabar 9 9

Code 11 8 9

Code 93 9 9

Composite Code 8 9

MSI 9 9

Plessey 9 8

Postal Codes 8 9

Telepen 9 8

Code 128 Code 128 9 9

EAN-128 9 9

9300 Mobile Compute

Reference Manual

ISBT-128 8 9

Code 2 of 5 Industrial 25 (i.e. Discrete 25) 9 9

Interleaved 25 9 9

Matrix 25 9 8

Code 3 of 9 Code 39 9 9

Trioptic Code 39 8 9

Italian Pharmacode (i.e. Code 32) 9 9

French Pharmacode 9 8

EAN/UPC EAN-8 9 9

EAN-13 9 9

Bookland EAN (i.e. ISBN) 9 9

UPC-E0 9 9

UPC-E1 8 9

UPC-A 9 9

RSS RSS-14 9 9

RSS Limited 9 9

RSS Expanded 9 9

2D Symbologies PDF417 8 9

MicroPDF417 8 9

Data Matrix 8 9

Maxicode 8 9

QR Code 8 9

Appendix I

Scan Engine Settings

RFID TAGS SUPPORTED

The RFID reader supports read/write operations depending on the tags. The supported

labels include ISO 15693, Icode®, Tag-it®, ISO 14443A, and ISO 14443B.

Currently, the performance of many tags has been confirmed, and the results are listed

below for your reference.

Note: You should study the specifications of RFID tags before use.

TI_RFID Module Version 1.0.A UID Only Read Page Write Page

ISO 14443A Mifare Standard 1K 9 --- ---

Mifare Standard 4K 9 --- ---

Mifare Ultralight 9 --- ---

Mifare DESFire 9 --- ---

Mifare S50 9 --- ---

SLE44R35 9 --- ---

SLE66R35 9 --- ---

ISO 14443B SRIX 4K --- --- ---

SR176 --- --- ---

ISO 15693 ICODE SLI 9 9 9

SRF55V02P 9 9 9

SRF55V02S 9 --- ---

SRF55V10P 9 9 9

TI Tag-it HF-I 9 9 9

ST LRI512 9 --- ---

Tag-it® Tag-it 9 9 9

ICODE®

(Phillips) ICODE --- --- ---

9300 Mobile Compute

Reference Manual

Appendix II

CCD/LASER SCAN ENGINE

The tables below list reader settings as well as symbology settings for the CCD or Laser

scan engine.

READER SETTINGS TABLE

CCD/Laser Description Default

Time-out 3 sec.

1~9 (second) for

93ReaderConfig.exe

0~255 (second) for

programming

Set the maximum time for decoding to continue during a scan attempt. It

applies to the following scan modes only –

 Aiming mode

 Laser mode

 Auto Off mode

 Auto Power Off mode

Scan Mode Laser mode

Continuous Mode Non-stop scanning

 To decode

the same barcode repeatedly, move away the scan beam

and target it at the barcode for each scanning.

Test Mode Non-stop scanning

 Capable of decoding the same barcode repeatedly

Repeat Mode Non-stop scanning

 Capable of re-transmitting barcode data if triggering within one second

after a successful decoding

Momentary Mode Hold down the scan trigger to start with scanning.

 The scanning won't stop until you release the trigger.

Alternate Mode Press the scan trigger to start with scanning.

 The scanning won't stop until you press the trigger again.

Aiming Mode Press the scan trigger to aim at a barcode. Within one second, press the

trigger again to decode the barcode.

 The scanning won't stop until (a) a barcode is decoded or (b) the

pre-set timeout expires.

Laser Mode Hold down the scan trigger to start with scanning.

 The scanning won't stop until (a) a barcode is read, (b) the preset

timeout expires, or (c) you release the trigger.

Auto Off Mode Press the scan trigger to start with scanning.

 The scanning won't stop until (a) a barcode is read or (b) the preset

timeout expires.

9300 Mobile Compute

Reference Manual

Auto Power Off Mode Press the scan trigger to start with scanning.

 The scanning won't stop until the preset timeout expires, and, the

preset timeout period re-counts after each successful decoding.

Read Redundancy None

None No redundancy means one successful decoding will make the reading valid

and induce the "READER Event".

One time, Two times,

or Three times The higher the reading security is (that is, the more redundancy the user

selects), the slower the reading speed gets.

 If "Three Times" is selected, it will take a total of four consecutive

successful decodings of the same barcode to make the reading valid.

SYMBOLOGY SETTINGS TABLE

CCD/Laser Description Default

Codabar Enable

Select Start/Stop

Characters If "Transmit Start/Stop Characters" is desired, select one

set:

 abcd / abcd

 abcd / tn*e

 ABCD / ABCD

 ABCD / TN*E

abcd / abcd

Transmit Start/Stop

Characters Decide whether to include the start

stop characters in the

data being transmitted. No

Code 128 Enable

EAN-128 Enable

Transmit Code ID Decide whether to include Code ID (“]C1”) will be included

in the data being transmitted. No

Industrial 25 (= Discrete 25) Enable

Start/Stop Selection This decides the readability of all 2 of 5 symbology

variants. For example, flight tickets actually use an

Industrial 2 of 5 barcode but with Interleaved 2 of 5

start/stop pattern. In order to read this barcode, the

start/stop pattern selection parameter of

Industrial 2 of 5

should set to "Interleaved 25".

Industrial 25

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Select Length  One or two fixed lengths

 Range 4~127

Interleaved 25 Enable

Start/Stop Selection Refer to Industrial 25. Interleaved

Appendix II

CCD/Laser Scan Engine

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Select Length  One or two fixed lengths

 Range 4~127

Matrix 25 Enable

Start/Stop Selection Refer to Industrial 25. Matrix 25

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Select Length  One or two fixed lengths

 Range 4~127

French Pharmacode Disable

*Transmit Start/Stop

Character Controlled by the same setting of Code 39. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Italian Pharmacode (= Code 32) Disable

*Transmit Start/Stop

Character Controlled by the same setting of Code 39. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Code 39 Enable

Transmit Start/Stop

Character Decide whether to include the start/stop characters "*" in

the data being transmitted. No

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Code 39 Full ASCII Code 39 Full ASCII includes all the alphanumeric and

special characters. Disable

Code 93 Enable

MSI Disable

Verify Checksum Select one of the three calculation formulas to verify the

checksum. If the checksum is incorrect, the barcode will

not be accepted.

 Single Modulo 10

 Double Modulo 10

 Modulo 11 & 10

Single Modulo

9300 Mobile Compute

Reference Manual

Transmit Checksum Decide whether to include the checksum in the data being

transmitted.

 Last digit not transmitted

 Both digits transmitted

 Both digits not transmitted

Both digits

transmitted

Select Length  One or two fixed lengths

 Range 4~127

Negative Barcode Disable

Plessey Disable

Convert to UK Plessey When applied, each occurrence of the character "A" in the

barcode data will be replaced by the character "X". No

Transmit Checksum Decide whether to include the checksum (2 digits) in the

data being transmitted. Yes

Telepen Disable

Original Telepen

(Numeric) The original Telepen includes numeric characters. Yes

AIM Telepen (Full

ASCII) AIM Telepen (Full ASCII) includes all the alphanumeric and

special characters. No

RSS-14 Disable

Transmit Code ID Decide whether to include Code ID (“]e0”) will be included

in the data being transmitted. Yes

Transmit Application

ID Decide whether to include the Application ID

("01") in the

data being transmitted. Yes

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

RSS Limited Disable

Transmit Code ID Refer to RSS-14. Yes

Transmit Application

ID Refer to RSS-14. Yes

Transmit Checksum Refer to RSS-14. Yes

RSS Expanded Disable

Transmit Code ID Refer to RSS-14. Yes

EAN-8 Enable

Convert to EAN-13 The EAN-8 barcode will be expanded into EAN-13, and the

next processing will follow the settings configured for

EAN-13.

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Addon 2 / Addon 5 Decide whether to decode EAN-8 with supplementals. No

EAN-13 / UPC-A Enable

ISBN Conversion The EAN-13 barcode starting with 978 and 979 will be

converted to ISBN. No

Appendix II

CCD/Laser Scan Engine

ISSN Conversion The EAN-13 barcode starting with 977 will be converted to

ISSN. No

GTIN for EAN-13 The EAN-13 barcode will be expanded into 14-digit Global

Trade Item Number (GTIN). No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. Yes

Addon 2 / Addon 5 Decide whether to decode EAN-13/UPC-A with

supplementals. No

(UPC-A) Convert to

EAN-13 The UPC-A barcode will be expanded into EAN-13, and the

next processing will follow the settings configured for

EAN-13.

Yes

(UPC-A) Transmit

Checksum Decide whether to include the UPC-A checksum in the data

being transmitted. Yes

(UPC-A) Transmit

System Number Decide whether to include the UPC-A System Number in

the data being transmitted. Yes

UPC-E Enable

Convert to UPC-A The UPC-E barcode will be expanded into UPC-A, and the

next processing will follow the settings configured for

UPC-A.

Transmit Checksum Decide whether to include the UPC-E checksum in the data

being transmitted. Yes

Transmit System

Number Decide whether to include the UPC-E System Number in

the data being transmitted. No

Addon 2 / Addon 5 Decide whether to decode UPC-E with supplementals. No

*It cannot read UPC-E1 barcodes!

9300 Mobile Compute

Reference Manual

Appendix III

2D SCAN ENGINE

The tables below list reader settings as well as symbology settings for the 2D scan

engine.

READER SETTINGS TABLE

2D Description Default

Decode Time-out Set the maximum time for decoding to continue during a

scan attempt.

 1~9 (second) for 93ReaderConfig.exe – default to 3

 5~99 (0.1 second) for programming – default to 30

3 sec.

Focus Mode Select the focus mode to control the working range:

 Far Focus – optimized to read at its far position

 Near Focus – optimized to read at its near position

 Smart Focus –

toggles the focus position after every

frame

Far Focus

Decode Illumination Decide whether to flash illumination on every barcode

capture to aid decoding.

 Turn On (Internal LED )

 Turn Off

Aiming Pattern Decide whether to project the aiming

pattern during

barcode capture.

 Turn On

 Turn Off

Read Redundancy Level 1

Level 1

he following barcodes must be successfully read twice before being

decoded:

Barcode Types Code Length

Codabar 8 characters or less

MSI 4 characters or less

Discrete 25 (=Industrial 25) 8 characters or less

Interleaved 25 8 characters or less

Level 2 All barcodes must be successfully read twice before being decoded.

Level 3 All barcodes except for the following barcodes must be successfully read

twice before being decoded.

The following barcodes must be read three times:

9300 Mobile Compute

Reference Manual

Barcode Types “Excluded” Code Length

Codabar 8 characters or less

MSI 4 characters or less

Discrete 25 (=Industrial 25) 8 characters or less

Interleaved 25 8 characters or less

Level 4 All barcodes must be successfully read three times before being decoded.

Security Level Select a decode security level appropriate for the barcode

quality when reading delta barcodes such as Code 128,

Code 93, UPC/EAN.

 Security Level 0 –

This default setting allows the scan

engine to operate in its most aggressive state,

providing sufficient security in decoding most “in-spec”

barcodes.

 Security Level 1 –

Select this option if misdecodes

occur. This level should eliminate most misdecodes.

 Security Level 2 –

Select this option if Security Level 1

fails to eliminate misdecodes.

 Security Level 3 –

Select this option if Security Level 2

also fails to eliminate misdecodes. However, selecting

this option impairs the decoding ability of the scan

engine. If this level of security is necessary, try to

improve the barcode quality.

Level 0

SYMBOLOGY SETTINGS TABLE

2D Description Default

Codabar Enable

CLSI Editing When applied, the CLSI editing strips the start/stop

characters and inserts a space after the first, fifth, and

tenth characters of a 14-character Codabar barcode.

 The 14-character barcode length does not include

start/stop characters.

NOTIS Editing Decide whether to include the start/stop characters in the

data being transmitted.

 NOTIS Editing is to strip the start/stop characters, i.e.

to disable "Transmit Start/Stop Characters".

Select Length  One or two fixed lengths

 Range (1~55) 4~55

Code 128 ---

Code 128 Read standard Code 128 barcodes (=without leading FNC1

character). Enable

UCC/EAN-128 Read UCC/EAN-128 barcodes with leading FNC1 character. Enable

ISBT 128 Read ISBT 128 barcodes. Enable

Appendix III 2D Scan Engine

Industrial 25 (= Discrete 25) Enable

Select Length  One or two fixed lengths

 Range (1~55) 4~55

Interleaved 25 Enable

Convert to EAN-13 Convert a 14-character barcode into EAN-13 if the

following requirements are met:

 The barcode must have a leading 0 and a valid EAN-13

check digit.

 “Verify Checksum” must be disabled.

Verify Checksum Decide whether to verify the checksum. If desired, select

one of the algorithms below. If the checksum is incorrect,

the barcode will not be accepted.

 No

 USS algorithm

 OPCC algorithm

Transmit Checksum Decide whether to include the checksum in the data being

transmitted.

 "Verify Checksum" must be enabled so that the

checksum can be left out (= "Transmit Checksum"

disabled).

Select Length  One or two fixed lengths

 Range (1~55) 4~55

Code 39 Enable

Convert to Code 32 Convert to Italian Pharmacode. No

Code 32 Prefix Prefix character "A" to Code 32 barcodes. No

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted. No

Transmit Checksum Decide whether to include the checksum in the data being

transmitted.

 "Verify Checksum" must be enabled so that the

checksum can be left out (= "Transmit Checksum"

disabled).

Code 39 Full ASCII Code 39 Full ASCII includes all the alphanumeric and

special characters. Disable

Select Length  One or two fixed lengths

 Range (1~55) 4~55

Trioptic Code 39 Disable

Code 93 Enable

Select Length  One or two fixed lengths

 Range (1~55) 4~55

9300 Mobile Compute

Reference Manual

MSI Enable

Verify Checksum If Two Check Digits option is selected, an additional

verification is required to ensure integrity. Select one of

the algorithms below. If the checksum is incorrect, the

barcode will not be accepted.

Check Digit Algorithm

One Check Digit Single Modulo 10

Two Check Digits  Mod 10/Mod 11

 Mod 10/Mod 10

Single Modulo

Transmit Checksum Decide whether to include the checksum in the data being

transmitted. No

Select Length  One or two fixed lengths

 Range (1~55) 4~55

RSS ---

RSS-14 Enable

RSS Limited Enable

RSS Expanded Enable

Convert RSS to

UPC/EAN

"Convert to UPC/EAN" only applies to RSS-14 and RSS

Limited barcodes not decoded as part of a Composite

barcode.

Convert to EAN-13

Strip the leading "010" from barcodes.

 "01" is the Application ID and must be followed by a

single zero (the first digit encoded)

Convert to UPC-A

Strip the leading "0100" from barcodes.

 "01" is the Application ID and must

be followed by

two or more zeros (but not six zeros)

EAN-8 Enable

Convert to EAN-13 The EAN-8 barcode will be expanded into EAN-13, and the

next processing will follow the settings configured for

EAN-13.

Addon 2 / Addon 5 Refer to UPC/EAN Addon setting.

EAN-13 Enable

Bookland EAN (=

ISBN) The EAN-13 barcode starting with 978 will be converted to

ISBN. Yes

Addon 2 / Addon 5 Refer to UPC/EAN Addon setting.

UPC-A Enable

Transmit Checksum Decide whether to include the UPC-A checksum in the data

being transmitted. Yes

Transmit Preamble Decide whether to include the UPC-A preamble System

Number (and Country Code) in the data being transmitted. System

Number

Addon 2 / Addon 5 Refer to UPC/EAN Addon setting.

UPC-E0 Enable

Appendix III 2D Scan Engine

Transmit Checksum Decide whether to include the UPC-E0 checksum in the

data being transmitted. Yes

Transmit Preamble Decide whether to include the UPC-E0 preamble System

Number (and Country Code) in the data being transmitted. System

Number

Addon 2 / Addon 5 Refer to UPC/EAN Addon setting.

Convert to UPC-A The UPC-E0 barcode will be expanded into UPC-A, and the

next processing will follow the settings configured for

UPC-A.

UPC-E1 Disable

Transmit Checksum Decide whether to include the UPC-E1 checksum in the

data being transmitted. Yes

Transmit Preamble Decide whether to include the UPC-E1 preamble System

Number (and Country Code) in the data being transmitted. System

Number

Addon 2 / Addon 5 Refer to UPC/EAN Addon setting.

Convert to UPC-A The UPC-E1 barcode will be expanded into UPC-A, and the

next processing will follow the settings configured for

UPC-A.

UCC Coupon Extended Code Disable

Read UPC-A barcodes starting with digit "5", EAN-13 barcodes starting with digits "99", and

UPC-A/EAN-128 Coupon Codes.

 UPC-A, EAN-13, and EAN-128 must be enabled first!

 Use “Addon Redundancy” to control auto-discrimination of the EAN-128 (right half) of a coupon

code.

UPC/EAN Addon ---

Addon 2 / Addon 5 Decide whether to decode EAN-8, EAN-13, UPC-E0,

UPC-E1, UPC-A with supplementals.

 Ignore Supplementals

 Decode Only With Supplementals

 Decode With Supplementals (= Auto-discriminate)

Ignore...

Addon Redundancy When "Decode with Supplementals" is applied, decide the

number of times of supplementary decoding the same

barcode that makes a valid reading.

10 times

Code 11 Enable

Verify Checksum Decide whether to verify the checksum. If the checksum is

incorrect, the barcode will not be accepted.

 No verification

 One Check Digit

 Two Check Digits

Transmit Checksum Decide whether to include the checksum in the data being

transmitted.

 "Verify Checksum" must be enabled so that the

checksum can be left out (= "Transmit Checksum"

disabled).

9300 Mobile Compute

Reference Manual

Select Length  One or two fixed lengths

 Range (1~55) 4~55

Postal Codes ---

US Postnet Enable

US Planet Enable

Transmit US Postal

Checksum US Postnet or US Planet must be enabled first! Enable

UK Postal Enable

Transmit UK Postal

Checksum UK Postal must be enabled first! Enable

Japan Postal Enable

Australian Postal Enable

Dutch Postal Enable

Composite Codes ---

Composite CC-C Enable

Composite CC-A/B Disable

Composite TLC-39 Disable

UCC/EAN Code 128

Emulation Mode Transmit data as if it was encoded in Code 128 barcodes.

 Transmit AIM Code Identifier must be enabled first!

Disable

UPC barcodes can be "linked" with a 2D barcode during

transmission as if they were one barcode. UPC Always

Linked

UPC Composite Mode

UPC Never Linked

Transmit UPC barcodes regardless of whether a 2D

barcode is detected.

UPC Always Linked

Transmit UPC barcodes and the 2D portion. If the 2D

portion is not detected, the UPC barcode will not be

transmitted.

 CC-A/B or CC-C must be enabled!

Auto-discriminate UPC Composites

Transmit UPC barcodes as well as the 2D portion if

present.

2D Symbologies ---

PDF417 Enable

MicroPDF417 Disable

MicroPDF417 Code 128

Emulation

ransmit data from certain MicroPDF417 barcodes as if it

was encoded in Code 128 barcodes.

 Transmit AIM Code Identifier must be enabled first!

Disable

Appendix III 2D Scan Engine

When applied, the MicroPDF417 barcodes are transmitted

with one of these prefixes:

The first codeword of MicroPDF417 is 903-907, 912,

914, 915:

The original Code ID "]L3" will be changed to "]C1".

The first codeword of MicroPDF417 is 908 or 909:

The original Code ID "]L4" will be changed to "]C2".

The first codeword of MicroPDF417 is 910 or 911:

The original Code ID "]L5" will be changed to "]C0".

Data Matrix Enable

Maxicode Enable

QR Code Enable

2D Symbologies - Macro PDF ---

Macro PDF is a special feature for concatenating multiple PDF barcodes into one file, known as

Macro PDF417 or Macro MicroPDF417.

Transmit/Decode Mode

Decide how to handle Macro PDF decoding.

Buffer All Symbols / Transmit Macro PDF When

Complete

Transmit all decoded data from an entire Macro PDF

sequence only when the entire sequence is scanned and

decoded. If the decoded data exceeds the limit of 50

symbols, no transmission because the entire sequence

was not scanned!

Transmit Any Symbol in Set / No Particular Order

Transmit data from each Macro PDF symbol as decoded,

regardless of the sequence.

Passthrough All Symbols

Transmit and decode all Macro PDF symbols and

perform no processing. In this mode, the host is

responsible for detecting and parsing the Macro PDF

sequences.

Passthrough

All Symbols

ESC Characters When enabled, it uses the backslash "\" as an Escape

character for systems that can process transmissions

containing special data sequences. It will format special

data according to the Global Label Identifier (GLI)

protocol, which only affects the data portion of a Macro

PDF symbol transmission. The Control Header, if enabled,

is always sent with GLI formatting.

None

9300 Mobile Compute

Reference Manual

Note: When printing barcodes, keep each Macro PDF sequence separate, as each has a

unique identifier. Do not mix barcodes from several Macro PDF sequences, even if

they encode the same data. When you scan Macro PDF sequences, scan the entire

Macro PDF sequence without interruption!

Image Capture Disable

Image Capture

Illumination Decide whether to flash illumination on every image

capture to aid decoding.

 Turn On (Internal LED )

 Turn Off

Image Capture

Autoexposure Decide whether to manually specify the gain and exposure

time (only recommended for advanced users with difficult

image capture situations).

Gain Time Only applies when Image Capture Autoexposure is

disabled.

 Gain is a means of amplifying the raw image data

before it is converted into 256 grayscale values.

Increasing the gain increases brightness and contrast,

but also increases noise (undesired electrical

fluctuations in the image) which makes the image less

attractive and/or harder to decode.

 Set the manual gain time in the range of 79~127.

100

Exposure Time Only applies when Image Capture Autoexposure is

disabled.

 Exposure Time controls the amount of time the CCD is

allowed to collect light, much like the shutter speed for

a camera.

Generally, the brighter the environment, the

lower the exposure time. Increasing the exposure time

past 20 ms in a handheld application increases the risk

of blurring the image due to hand jitter.

 Set the manual exposure time to one of the following

values — 5 ms, 10 ms, 15 ms, 20 ms, 25 ms, or 30

ms.

10 ms

Snapshot Aiming

Pattern Decide whether to project the aim pattern while capturing

an image. On

Image Resolution Decide how to alter image resolution before compression.

Multiple pixels are combined to one pixel, resulting in a

smaller image containing the original content with reduced

resolution.

 640×480 (Full resolution)

 320×240 (Half resolution)

 212×160 (1/3 resolution)

 160×1420 (1/4 resolution)

640×480

Image Format Decide in which file format the image is saved.

 JPEG file format

 BMP file format

JPEG

Appendix III 2D Scan Engine

Optimized for JPEG

Quality Decide whether JPEG images are optimized for quality.

 Cancel the check box so that JPEG images are

optimized for size.

Enable

Select JPEG Quality Set a value from 5 to 100, where “100” represents the

highest quality image. 65

Select JPEG Size Set a value from 5 to 150, which represents the file size in

multiples of 1024 bytes (1K). For example, setting this

value to 8 permits the file size to be as large as 8192

bytes.

Bits per Pixel Select the number of significant bits per pixel (BPP) to use

when capturing an image.

 1 bit per pixel (for black and white images)

 4 BPP (to assign 1 of 16 levels of grey to each pixel)

 8 BPP (to assign 1 of 256 levels of grey to each pixel)

Note: (1) For JPEG files, these BPP settings are ignored for it always uses 8 bits per pixel!

(2) When the image capture feature is enabled, press the [SCAN] button and it will

capture an image instead of reading a barcode.

Miscellaneous Options ---

Transmit Code ID Decide whether to include AIM Code ID in the beginning of

data. Each AIM Code ID contains the three-character string

“]cm” –

 ] = Flag Character (ASCII 93)

 c = Code Character (see below)

 m = Modifier Character (see below)

Disable

9300 Mobile Compute

Reference Manual

AIM CODE ID – CODE CHARACTERS

Code Character Code Type

A Code 39, Code 39 Full ASCII, Code 32

C Code 128, Coupon (Code 128 portion)

d Data Matrix

E UPC/EAN, Coupon (UPC portion)

e RSS Family

F Codabar

G Code 93

H Code 11

I Interleaved 25

L PDF417, Macro PDF417, Micro PDF417

M MSI

Q QR Code

S Discrete 25, IATA 2 of 5

U Maxicode

X Code 39 Trioptic, Bookland EAN, US Postnet, US Planet, UK Postal, Japan

Postal, Australian Postal, Dutch Postal

AIM CODE ID – MODIFIER CHARACTERS

Code Type Option Value Option

0 No check character or Full ASCII processing.

1 Checksum has been verified.

3 Checksum has been verified and stripped.

4 Full ASCII conversion has been performed.

5 Result of option values 1 and 4.

Code 39

7 Result of option values 3 and 4.

0 Standard data packet. No Function Code 1“FNC1” in the first

character position.

1 Function Code 1“FNC1” in the first character position.

Code 128

2 Function Code 1“FNC1” in the second character position.

0 No check digit processing.

1 Checksum has been verified.

Interleaved 25

3 Checksum has been verified and stripped.

Codabar 0 No check digit processing.

Code 93 0 Always transmit 0.

Appendix III 2D Scan Engine

0 Modulo 10 check digit verified and transmitted. MSI

1 Modulo 10 check digit verified but not transmitted.

Discrete 25 0 Always transmit 0.

0 Standard data packet in full EAN country code format, which

is 13 digits for UPC-A and UPC-E (not including

supplemental data).

3 Standard data packet with two-digit or five-digit

supplemental data.

4 EAN-8 data packet.

UPC/EAN

A UPC-A with Addon 2 barcode, 012345678905-10, is transmitted to the host

as a 18-character string, ]E3001234567890510.

Bookland EAN 0 Always transmit 0.

Trioptic Code 39 0 Always transmit 0.

0 Single check digit (has been verified.)

1 Two check digits (has been verified.)

Code 11

3 Checksum has been verified but not transmitted.

0 Always transmit 0. RSS Family

RSS-14 and RSS Limited will be transmitted with an Application Identifier

“01”. For example, an RSS-14 barcode, 100123456788902, is transmitted

as ]e001100123456788902.

Note: In UCC/EAN-128 emulation mode, RSS is transmitted using Code 128 rules (i.e.

“]C1”).

Native mode transmission

0 Standard data packet

1 Data packet containing the data following an encoded

symbol separator character.

2 Data packet containing the data following an escape

mechanism character. The data packet does not support the

ECI protocol.

3 Data packet containing the data following an escape

mechanism character. The data packet supports the ECI

protocol.

UCC/EAN-128 emulation

EAN.UCC

Composites (RSS,

UCC/EAN-128, 2D

portion of UPC

composite)

1 Data packet is a UCC/EAN-128 barcode (i.e. data is

preceded with “]JC1”).

Note: UPC portion of composite is transmitted using UPC rules.

PDF417,

Micro PDF417

0 Scan engine is set to conform to protocol defined in 1994

PDF417 symbology specifications.

 When this option is transmitted, the receiver cannot

reliably determine whether ECIs have been invoked or

whether data byte 92DEC has been doubled in

9300 Mobile Compute

Reference Manual

transmission.

1 Scan engine is set to follow the ECI protocol (Extended

Channel Interpretation). All data characters 92DEC are

doubled.

2 Scan engine is set for Basic Channel operation (no escape

character transmission protocol). Data characters 92DEC

are not doubled.

 When decoders are set to this mode, unbuffered Macro

symbols and symbols requiring the decoder to convey

ECI escape sequences cannot be transmitted.

3 The barcode contains a UCC/EAN-128 symbol, and the first

codeword is 903-907, 912, 914, 915.

4 The barcode contains a UCC/EAN-128 symbol, and the first

codeword is in the range 908-909.

5 The barcode contains a UCC/EAN-128 symbol, and the first

codeword is in the range 910-911.

A PDF417 barcode, ABCD, with no transmission protocol enabled, is

transmitted as ]L2ABCD.

0 ECC 000-140, not supported.

1 ECC 200.

2 ECC 200, FNC1 in first or fifth position.

3 ECC 200, FNC1 in second or sixth position.

4 ECC 200, ECI protocol implemented.

5 ECC 200, FNC1 in first or fifth position, ECI protocol

implemented.

Data Matrix

6 ECC 200, FNC1 in second or sixth position, ECI protocol

implemented.

0 Mode 4 or 5

1 Mode 2 or 3

2 Mode 4 or 5, ECI protocol implemented.

Maxicode

3 Mode 2 or 3, ECI protocol implemented in secondary

message.

0 Model 1

1 Model 2, ECI protocol not implemented.

2 Model 2, ECI protocol implemented.

3 Model 2, ECI protocol not implemented, FNC1 implied in

first position.

4 Model 2, ECI protocol implemented, FNC1 implied in first

position.

5 Model 2, ECI protocol not implemented, FNC1 implied in

second position.

QR Code

6 Model 2, ECI protocol implemented, FNC1 implied in second

position

Appendix III 2D Scan Engine

User Manual

Windows CE Mobile Compute

9300

Version 0.09

The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided

under a license agreement containing restrictions on use and disclosure and is also

protected by copyright law. Reverse engineering of the software is prohibited.

Due to continued product development this information may change without notice. The

information and intellectual property contained herein is confidential between CIPHERLAB

and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find

any problems in the documentation, please report them to us in writing. CIPHERLAB

does not warrant that this document is error-free.

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photocopying,

recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.

For product consultancy and technical support, please contact your local sales

representative. Also, you may visit our web site for more information.

The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and/or other countries.

Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.

Other product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies and are hereby acknowledged.

The editorial use of these names is for identification as well as to the benefit of the

owners, with no intention of infringement.

CIPHERLAB CO., LTD.

Website: http://www.cipherlab.com