Cisco Linksys BEFW11S4V32 Wireless Access Point Router with 4-Port Switch User Manual Part 1

Download:
Mirror Download [FCC.gov]
Document ID	317753
Application ID	SKUVcx9EWpw5BsFO9lIydw==
Document Description	Users Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	206.36kB (2579481 bits)
Date Submitted	2003-04-14 00:00:00
Date Available	2003-04-14 00:00:00
Creation Date	2002-10-16 11:05:12
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2003-03-31 16:28:53
Document Title	Users Manual Part 1

Instant WirelessTM Series
Wireless Access Point Router with 4-Port Switch
The Reset Button
The Wireless Access Point Router’s Ports
Pressing the Reset Button and holding it in for a few seconds will clear all
of the Router’s data and restore the factory defaults. This should be done
only if you are experiencing heavy routing problems, and only after you
have exhausted all of the other troubleshooting options. By resetting the
Router, you run the risk of creating conflicts between your PCs’ actual IP
Addresses and what the Router thinks their IP Addresses should be. You
may be forced to reboot each network PC.
If the Router locks up, simply press the reset button or power it down for
three to five seconds by removing the power cable from the Router’s
Power Port. Leaving the power off for too long could result in the loss of
network connections.
The Wireless Access Point Router’s LEDs
Figure 1-1
The Router’s rear panel (as shown in Figure 1-1) is where all of its connections
are made.
WAN
The WAN (Wide Area Network) Port is where you will connect your cable or DSL modem with an Ethernet cable. Your
modem connection will not work from any other port.
Figure 1-2
The LAN Indicators
Ports 1-4
Uplink
Power
These four LAN (Local Area Network) ports are where you
will connect networked devices, such as PCs, print servers,
and any other Ethernet devices you want to put on your network. If Port 4 is being used, the Uplink Port will not work.
The Uplink Port is where you can expand your network by
connecting to another switch or hub. Uplinking to another
switch or a hub is done by simply running a cable from the
Uplink Port to the other device. The Uplink Port is shared
with Port 4. If the Uplink port is being used, Port 4 will not
work.
The Power Port is where you will connect the included AC
Power adapter.
WLAN Act
Green. This LED indicates wireless activity.
WLAN Link
Green. This LED indicates that the Router’s wireless functions have been enabled through the Web-based utility.
Power
Green. This LED indicates that the Router’s power is on.
Link/Act
Green. This LED serves two purposes. When this LED is lit
continuously, this indicates that the Router is connected to a
device through the corresponding port (1, 2, 3, or 4). A blinking LED indicates that the Router is actively sending or
receiving data over that port. When the Uplink Port is in use,
the LED for Port 4 will be lit continuously.
Antenna Jacks The Antenna Jacks are where the included antennas are connected.
Instant WirelessTM Series
Full/Col
100
Green. This LED also serves two purposes. When this LED
is lit continuously, the connection made through the corresponding port is running in Full Duplex mode. A blinking
LED indicates that the connection is experiencing collisions.
Infrequent collisions are normal. If this LED blinks too
often, there may be a problem with your connection. Refer to
the Troubleshooting Appendix if you think there is a problem.
Orange. This LED indicates when a successful 100Mbps
connection is made through the corresponding port.
The WAN Indicators
Wireless Access Point Router with 4-Port Switch
Chapter 2: Connecting the Router
Before You Start
Before plugging everything together, it’s always a good idea to have everything
you’ll need to get the Router up and running. Depending upon how you configure the Router in Chapter 4: Configuring the Router, you may need some of the
following values from your ISP:
When connecting through a Static IP connection, be sure to have 1) Your
broadband-configured PC’s fixed Internet IP Address, 2) Your broadbandconfigured PC’s Computer Name and Workgroup Name, 3) Your Subnet
Mask, 4) Your Default Gateway, and 5) Your Primary DNS IP address.
Link
Green. This LED indicates a connection between the Router
and your broadband device or network.
When connecting through a PPPoE connection, be sure to have 1) Your
PPPoE User Name and 2) Your PPPoE Password.
Act
Green. This LED blinks when the Router is sending or
receiving data over the broadband (WAN) port.
Diag
Red. This LED indicates the Router’s self-diagnosis mode
during boot-up and restart. It will turn off upon completing
the diagnosis. If this LED stays on for an abnormally long
period of time, refer to the Troubleshooting Appendix.
The installation technician from your ISP should have left this information with
you after installing your broadband connection. If not, you can call your ISP to
request the data.
Once you have the above values, you can begin the Router’s installation and
setup.
Connecting Your Hardware Together and Booting Up
Once you are sure that you have the above values on hand, you can begin the
Installation and Setup of the Router.
1. Power everything down, including your PCs, your cable or DSL modem and
the Router.
2. Connect an Ethernet cable from one of
your PC’s Ethernet ports to one of the
Router’s LAN ports (as shown in Figure 21). Do the same with all the PCs you wish
to connect to the Router. (LAN Port 4 will
become inactive if you use the Uplink
port.)
In addition to accessing the Router through
an Ethernet connection, a wireless connec-
Figure 2-1
Instant WirelessTM Series
tion can be used to access the Router. See the “For Wireless Connections”
section that follows these connection instructions.
3. Connect another Ethernet cable from your
cable or DSL modem to the Router’s WAN
port (as shown in Figure 2-2).
4. Connect the Power Adapter (included) to
the Router’s Power port (as shown in
Figure 2-3) and plug the other end into a
power outlet.
Figure 2-2
Wireless Access Point Router with 4-Port Switch
For Wireless Connections: In addition to accessing the Router through an
Ethernet connection, a wireless connection can be used to access the Router.
After powering on the Router and connecting it to your modem, enter the
Router’s IP Address in the Address field of your wireless PC’s web-browser as
follows: http://192.168.1.1 and press Enter.
Important: The Wireless Access Point Router with 4-Port Switch is
configured by default to work out of the box with all Linksys Wireless
Adapters. If you have changed the defaults on your Linksys Wireless
Adapters, or are using other wireless adapters, you must temporarily change your wireless adapter settings to: (SSID = linksys) in
order to initially access the Router wirelessly. After you have
accessed the Router with the default settings, you can change the
router settings to coincide with your Network settings and reset your
adapters.
Important: Some ISPs—most notably some cable providers—configure their networks so that you do not have to enter a full Internet
address into your web browser or e-mail application to reach your
home page or receive your e-mail. If your Internet home page
address is something very simple, such as “www”, rather than
“www.linksys.com”, or your e-mail server’s address is something similar to “e-mail” or “pop3”, rather than “pop.mail.linksys.com”, you
won’t be able to properly configure the Router until you determine the
actual Internet addresses of your Web and e-mail connections.
• The Power LED will illuminate green
as soon as the power adapter is connected.
• The Diag LED will illuminate red for a
few seconds while the Router goes
through its internal diagnostic test. The
LED will turn off when the self-test is
complete.
Figure 2-3
5. Power on the cable or DSL modem. Verify
that the power is on by checking the Link LED in the WAN column on the
front of the Router. The Link LED will be illuminated if the power is on and
the modem is ready.
You must obtain this information prior to connecting the Router to
your network. You can obtain this information by contacting your ISP.
6. Press the Reset button on the back of the Router. Hold the button in for three
seconds, or until the Diag LED illuminates red. This restores the Router’s
default settings.
7. Power on your PC.
The Router is now connected. Continue to the next chapter to configure
your PCs.
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2002:10:16 11:05:12Z
Modify Date                     : 2003:03:31 16:28:53+08:00
Page Count                      : 3
Creation Date                   : 2002:10:16 11:05:12Z
Producer                        : Acrobat Distiller 4.0 for Windows
Mod Date                        : 2003:03:31 11:19:47+08:00
Metadata Date                   : 2003:03:31 11:19:47+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools