Cisco Systems 102042 AIR-MPI352 series User Manual AP370axB

Download:
Mirror Download [FCC.gov]
Document ID	231074
Application ID	luoTN7eMmHtJLjf6zmeD6A==
Document Description	031402 manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.46kB (405711 bits)
Date Submitted	2002-03-14 00:00:00
Date Available	2002-03-28 00:00:00
Creation Date	2002-02-25 17:07:58
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2002-02-26 07:23:03
Document Title	AP370axB.fm
Document Creator	FrameMaker 5.5.6p145

Beta Draft 1 - Cisco Conf i denti al
A P P E N D I X
Declarations of Conformity and Regulatory
Information
This appendix provides declarations of conformity and regulatory information for the Cisco Aironet
1200 series access points.
This appendix contains the following sections:
•
Manufacturers Federal Communication Commission Declaration of Conformity Statement
•
Department of Communications – Canada
•
European Community, Switzerland, Norway, Iceland, and Liechtenstein
•
Declaration of Conformity for RF Exposure
•
Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
OL-2155-01
B-1
Appendix B
Manufacturers Federal Communication Commission Declaration of Conformity Statement
Declarations of Conformity and Regulatory Information
Beta Draft 1 - Cisco Conf i denti al
Manufacturers Federal Communication Commission
Declaration of Conformity Statement
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Models:
AIR-AP1200B w/AIR-MP20B-A-K9, AIR-AP1220B-A-K9
FCC Certification number:
LDK 102042 (AIR-AP12xx)
Manufacturer:
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates,
uses, and radiates radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference. However, there is no guarantee that interference will not
occur. If this equipment does cause interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to correct the interference by one of the
following measures:
Caution
•
Reorient or relocate the receiving antenna.
•
Increase separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician.
The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the antennas listed in Table B-1. Any changes or modification to said product not
expressly approved by Cisco could void the user’s authority to operate this device.
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
B-2
OL-2155-01
Appendix B
Declarations of Conformity and Regulatory Information
Department of Communications – Canada
Beta Draft 1 - Cisco Conf i denti al
Table B-1
Access Point Antennas
Cisco Part Number
Model
Gain
AIR-ANT1949
Yagi
13.5
AIR-ANT4121
Omni-directional
12.0
AIR-ANT3549
Patch
8.5
AIR-ANT2012
Spatial diversity
6.5
AIR-ANT1729
Patch
6.0
AIR-ANT2506
Omni-directional
5.1
AIR-ANT3213
Omni-directional
5.0
AIR-ANT1728
Omni-directional
5.0
AIR-ANT3195
Patch
3.0
AIR-ANT5959
Omni-directional
2.0
AIR-ANT4941
Dipole
2.2
Department of Communications – Canada
Canadian Compliance Statement
This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two
conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
The device is certified to the requirements of RSS-139-1 and RSS-210 for 2.4-GHz spread spectrum
devices. The use of this device in a system operating either partially or completely outdoors may require
the user to obtain a license for the system according to the Canadian regulations. For further information,
contact your local Industry Canada office.
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
OL-2155-01
B-3
Appendix B
Declarations of Conformity and Regulatory Information
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Beta Draft 1 - Cisco Conf i denti al
European Community, Switzerland, Norway, Iceland, and
Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
B-4
OL-2155-01
Appendix B
Declarations of Conformity and Regulatory Information
Declaration of Conformity for RF Exposure
Beta Draft 1 - Cisco Conf i denti al
The Declaration of Conformity related to this product can be found at the following URL:
http://www.ciscofax.com
For the 1200 series, the following standards were applied:
•
Radio:
EN 300.328-1, EN 300.328-2
•
EMC:
EN 301 489-1, EN 301 489-17
•
Safety:
EN 60950
The following CE mark is affixed to the 1200 series equipment:
The above CE mark is required as of April 8, 2000 but might change in the future
Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate
Compliance.
Note
Combinations of power levels and antennas resulting in a radiated power level of above 100 mW eirp are
considered as not compliant with the above mentioned directive and are not allowed for use within the
European community and countries that have adopted the European R&TTE directive 1999/5/EC and/or
the CEPT recommendation Rec 70.03. For more details on legal combinations of power levels and
antennas, contact Cisco Corporate Compliance.
Declaration of Conformity for RF Exposure
The radio module has been evaluated under FCC Bulletin OET 65C and found compliant to the
requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure
from radio frequency devices. For antennas AIR-ANT4121 and AIR-ANT1949, the equipment should
be positioned more than 2 m from your body or nearby persons. For all other approved antennas the
equipment should be installed more than 20 cm from your body or nearby persons.
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
OL-2155-01
B-5
Appendix B
Declarations of Conformity and Regulatory Information
Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan
Beta Draft 1 - Cisco Conf i denti al
Guidelines for Operating Cisco Aironet Access Points and
Bridges in Japan
This section provides guidelines for avoiding interference when operating Cisco Aironet access points
and bridges in Japan. These guidelines are provided in both Japanese and English.
03-5549-6500
43768
Japanese Translation
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices
such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio
stations and unlicensed specified low-power radio stations) used in factory production lines.
1.
Before using this equipment, make sure that no premises radio stations or specified low-power radio
stations of RF-ID are used in the vicinity.
2.
If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the
frequency or stop using the device; contact the number below and ask for recommendations on
avoiding radio interference, such as setting partitions.
3.
If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact
the number below.
Contact Number: 03-5549-6500
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
B-6
OL-2155-01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2002:02:25 17:07:58
Producer                        : Acrobat Distiller 4.05 for Windows
Title                           : AP370axB.fm
Creator                         : FrameMaker 5.5.6p145
Modify Date                     : 2002:02:26 07:23:03-05:00
Page Count                      : 6
Page Mode                       : UseOutlines

EXIF Metadata provided by EXIF.tools