Cisco Systems 102070 Cisco Aironet 802.11n Draft 2.0 Dual Band Access Point User Manual ap1140getstart

Cisco Systems Inc Cisco Aironet 802.11n Draft 2.0 Dual Band Access Point ap1140getstart

User Manual

REVIEW DRAFT—CISCO CONFIDENTIALGETTING STARTED GUIDE Cisco Aironet 1140 Series Access PointINCLUDING LICENSE AND WARRANTY1About this Guide2Taking Out What You Need3Overview4Installing the Access Point5Configuring the Access Point6Troubleshooting7Declarations of Conformity and Regulatory Information8Configuring Option 439Access Point Specificationsap1140getstart.fm Page 1 Monday, June 16, 2008 8:49 AM
2REVIEW DRAFT—CISCO CONFIDENTIALRevised: Month Day, Year, OL-16415-011 About this GuideThis Guide provides instructions on how to install and configure your Cisco Aironet 1140 Series Access Point. It also covers ====TBD=====2 Taking Out What You NeedFollow these steps:Step 1 Unpack and remove the access point and the accessory kit from the shipping box.Step 2 Return any packing material to the shipping container and save it for future use.Step 3 Verify that you have received the items shown in. If any item is missing or damaged, contact your Cisco representative or reseller for instructions.Figure 1 Shipping Box Contents.......ILLUSTRATION SHOWING BOX CONTENTS.3 OverviewThe following illustrations show the connections and of the access pointap1140getstart.fm Page 2 Monday, June 16, 2008 8:49 AM
3REVIEW DRAFT—CISCO CONFIDENTIALFigure 2 Access Point Ports and Connections4 Installing the Access PointThe access point can be mounted on a ceiling, wall, or flat horizontal surface such as a table or desk top. For ceiling and wall mounted units, the access point can be mounted on existing mounting hardware for the 1100, 1200, or 1240 series access points. Mounting the Access Point on a Suspended CeilingFollow these steps to mount the access point on a suspended ceiling.Step 1 TBD1Power jack 4Security padlock connection2Console port? 5Kensington lock connection3Ethernet port 6ap1140getstart.fm Page 3 Monday, June 16, 2008 8:49 AM
4REVIEW DRAFT—CISCO CONFIDENTIALStep 2 TBD === NEED ILLUSTRATIONSMounting the Access Point Using Existing Mounting Hardware1100 SeriesFollow these steps to mount the access point on an existing 1100 series installation. Step 1 TBD ==== ILLUSTRATION(S)Step 2 TBD1200 SeriesFollow these steps to mount the access point on an existing 1200 series installation.Step 1 TBD ==== ILLUSTRATION(S)Step 2 TBD1240 SeriesFollow these steps to mount the access point on an existing 1240 series installationStep 1 TBD ==== ILLUSTRATION(S)Step 2Mounting the Access Point on a WallFollow these steps to mount the access point on a wall.Step 1 ====ILLUSTRATION(S)ap1140getstart.fm Page 4 Monday, June 16, 2008 8:49 AM
5REVIEW DRAFT—CISCO CONFIDENTIALStep 2Connecting PowerThe access point is 802.3af (13 watts) compliant and can be powered by any of the following 802.3af compliant controllers or switches: • 2106 controller • WS-C3550, WS-C3560, WS-C3750 • C1880 • 2600, 2610, 2611, 2621, 2650, 2651 • 2610XM, 2611XM, 2621XM, 2650XM, 2651XM, 2691 • 2811, 2821, 2851 • 3620, 3631-telco, 3640, 3660 • 3725, 3745 • 3825, 3845The access point can also be powered by any of the following optional external power sources: • Any 802.3af compliant power injector • 1250 series access point power injector (if using Gigabit Ethernet) • 1200 Series access point DC power supply • 1250 series access point DC power supply5 Configuring the Access PointThis section describes how to connect the access point to a wireless LAN controller. ======ARE THERE ANY PRECONDITIONING COMMANDS AVAILABLE? ======The Controller Discovery ProcessThe 1140 series access point uses the IETF standard Control and Provisioning of Wireless Access Points Protocol (CAPWAP) to communicate between the controller and other wireless access points on the network. CAPWAP is a standard, interoperable protocol which enables an access controller to manage a collection of wireless termination points. The discovery process using CAPWAP is identical to the Lightweight Access Point Protocol (LWAPP) used with previous Cisco Aironet access points. ap1140getstart.fm Page 5 Monday, June 16, 2008 8:49 AM
6REVIEW DRAFT—CISCO CONFIDENTIALLWAPP enabled access points are compatible with CAPWAP and conversion to a CAPWAP controller is seamless. Deployments can have a mix of CAPWAP and LWAPP software running on the controllers. The CAPWAP enabled software will allow for access points to join either a controller running CAPWAP or LWAPP.The functionality provided by the controller does not change except for customers that have Layer 2 deployments, which CAPWAP does not support.In an CAPWAP environment, a wireless access point discovers a controller by using CAPWAP discovery mechanisms and then sends it an CAPWAP join request. The controller sends the access point a CAPWAP join response allowing the access point to join the controller. When the access point joins the controller, the controller manages its configuration, firmware, control transactions, and data transactions.Note For additional information about the discovery process and CAPWAP, see the Cisco Wireless LAN Controller Software Configuration Guide. This document is available on cisco.com.Note CAPWAP support is provided in controller software release 5.2 or greater. Note Cisco controllers cannot edit or query any access point information using the CLI if the name of the access point contains a space.Note Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the access point might not join the controller because its certificate may not be valid for that time.Follow these steps to prepare the access point and connect it to the wireless network.Step 1 TBD ==== ILLUSTRATION(S)Step 2ap1140getstart.fm Page 6 Monday, June 16, 2008 8:49 AM
7REVIEW DRAFT—CISCO CONFIDENTIAL6 TroubleshootingGuidelines for Using Cisco Aironet Lightweight Access PointsKeep these guidelines in mind when you use a 1140 series lightweight access point: • The access point can only communicate with Cisco controllers, such as the 2106 series wireless LAN controllers or 4400 series controllers. • The access point does not support Wireless Domain Services (WDS) and cannot communicate with WDS devices. However, the controller provides functionality equivalent to WDS when the access point associates to it. • CAPWAP does not support Layer 2. The access point must get an IP address and discover the controller using DHCP, DNS, or IP subnet broadcast. • The access point console port is enabled for monitoring and debug purposes (all configuration commands are disabled when connected to a controller). Using DHCP Option 43You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling the access point to find and join a controller. For additional information, refer to the “Configuring Option 43” section on page 22.Checking the Lightweight Access Point LEDsIf your lightweight access point is not working properly, check the Status, Ethernet, and Radio LEDs. You can use the LED indications to quickly assess the unit’s status. Figure 3 shows the location of the access point LEDs.ap1140getstart.fm Page 7 Monday, June 16, 2008 8:49 AM
8REVIEW DRAFT—CISCO CONFIDENTIALFigure 3 Access Point LED Locationap1140getstart.fm Page 8 Monday, June 16, 2008 8:49 AM
9REVIEW DRAFT—CISCO CONFIDENTIALTable 1 shows the access point LED status indications for various conditions.Ta b l e 1 LED Status Indications Message TypeEthernet LEDRadio LEDStatus LEDMessageMeaningBoot loader status Green Amber –DRAM memory test in progress.Green Green Green DRAM memory test OK.–Red –Board initialization in progress.–Blinking GreenBlinking GreenInitializing Flash file system.–Green Green Flash memory test OK.Amber –White Initializing Ethernet.Green –Blinking blueEthernet OK.Green Green Blinking greenStarting Cisco IOS.– – – Initialization OK.Association status – – Green Normal operating condition, no wireless client device associated.– – Blue Normal operating condition, wireless client devices associated.Operating status Green – – Ethernet link is operational.Blinking green– – Transmitting or receiving Ethernet packets.–Blinking green–Transmitting or receiving radio packets.– – Blinking blueSoftware upgrade in progress.Blinking greenBlinking greenBlinking greenAccess point location command.ap1140getstart.fm Page 9 Monday, June 16, 2008 8:49 AM
10REVIEW DRAFT—CISCO CONFIDENTIALBoot loader warnings– – Blinking redEthernet link not operational.Red –Red Ethernet failure.Amber –Blinking blueConfiguration recovery in progress. (Mode button pushed for 2 to 3 seconds).–Red Red Image recovery in progress. (Mode button pressed for 20 to 30 seconds).Blinking greenRed Blinking greenImage recovery in progress and Mode button is released.Boot loader errors Red Red Red DRAM memory test failure.–Red Blinking red and blueFlash file system failure.–Amber Alternating red and greenEnvironment variable failure.Amber –Rapidly blinking redBad MAC address.Red –Blinking red and offEthernet failure during image recovery.Amber Amber Blinking red and offBoot environment error.Red Amber Blinking red and offNo Cisco IOS image file.Amber Amber Blinking red and offBoot failure.Table 1 LED Status Indications (continued)Message TypeEthernet LEDRadio LEDStatus LEDMessageMeaningap1140getstart.fm Page 10 Monday, June 16, 2008 8:49 AM
11REVIEW DRAFT—CISCO CONFIDENTIAL==== ADDITIONAL INFO TBD ====7 Declarations of Conformity and Regulatory InformationThis section provides declarations of conformity and regulatory information for the Cisco Aironet 1140 Series Access Point.Manufacturers Federal Communication Commission Declaration of Conformity StatementCisco IOS errors Blinking amber– – Transmit or receive Ethernet errors.–Blinking amber–Maximum retries or buffer full occurred on radio.Red Red –Software failure; try disconnecting and reconnecting power.– – Cycling through blue, green, red, and offGeneral warning, insufficient inline power.Table 1 LED Status Indications (continued)Message TypeEthernet LEDRadio LEDStatus LEDMessageMeaningTested To ComplyWith FCC StandardsFOR HOME OR OFFICE USEap1140getstart.fm Page 11 Monday, June 16, 2008 8:49 AM
12REVIEW DRAFT—CISCO CONFIDENTIALManufacturer:Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USAThis device complies with Part 15 rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from which the receiver is connected. • Consult the dealer or an experienced radio/TV technician.Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.Models Certification NumbersAIR-(L)AP1141N-A-K9 LDK102069AIR-(L)AP1142N-A-K9 LDK102070ap1140getstart.fm Page 12 Monday, June 16, 2008 8:49 AM
13REVIEW DRAFT—CISCO CONFIDENTIALCaution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the UNII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.VCCI Statement for JapanIndustry CanadaCanadian Compliance StatementThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.WarningThis is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.Models Certification NumbersAIR-(L)AP1141N-A-K9 2461B-102069AIR-(L)AP1142N-A-K9 2461B-102070ap1140getstart.fm Page 13 Monday, June 16, 2008 8:49 AM
14REVIEW DRAFT—CISCO CONFIDENTIALCet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.European Community, Switzerland, Norway, Iceland, and LiechtensteinModels:AIR-(L)AP1142N-E-K9 AIR-(L)AP1141N-E-K9ap1140getstart.fm Page 14 Monday, June 16, 2008 8:49 AM
15REVIEW DRAFT—CISCO CONFIDENTIALDeclaration of Conformity with Regard to the R&TTE Directive 1999/5/ECap1140getstart.fm Page 15 Monday, June 16, 2008 8:49 AM
16REVIEW DRAFT—CISCO CONFIDENTIALThis device complies with the EMC requirements (EN 60601-1-2) of the Medical Directive 93/42/EEC.For 2.4 GHz radios, the following standards were applied: • Radio—EN 300.328-1, EN 300.328-2 • EMC—EN 301.489-1, EN 301.489-17 • Safety—EN 60950-1ap1140getstart.fm Page 16 Monday, June 16, 2008 8:49 AM
17REVIEW DRAFT—CISCO CONFIDENTIALNote This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.For 54 Mbps, 5 GHz access points, the following standards were applied: • Radio—EN 301.893 • EMC—EN 301.489-1, EN 301.489-17 • Safety—EN 60950-1The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio:Declaration of Conformity for RF ExposureUnited StatesThis system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin 65C rev 01.01. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance. Canada This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on RSS-102 Rev 2. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance. European UnionThis system has been evaluated for RF exposure for Humans in reference to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 50385 Product Standard to Demonstrate Compliance of Radio Base stations and Fixed Terminals for ap1140getstart.fm Page 17 Monday, June 16, 2008 8:49 AM
18REVIEW DRAFT—CISCO CONFIDENTIALWireless Telecommunications Systems with basic restrictions or reference levels related to Human Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum separation distance from the antenna to general bystander is 20cm (7.9 inches). AustraliaThis system has been evaluated for RF exposure for Humans as referenced in the Australian Radiation Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits. The minimum separation distance from the antenna to general bystander is 20cm (7.9 inches). Guidelines for Operating Cisco Aironet Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.Japanese Translation03-6434-650043768ap1140getstart.fm Page 18 Monday, June 16, 2008 8:49 AM
19REVIEW DRAFT—CISCO CONFIDENTIALEnglish TranslationThis equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.Contact Number: 03-5549-6500Administrative Rules for Cisco Aironet Access Points in TaiwanThis section provides administrative rules for operating Cisco Aironet access points in Taiwan. The rules are provided in both Chinese and English.ap1140getstart.fm Page 19 Monday, June 16, 2008 8:49 AM
20REVIEW DRAFT—CISCO CONFIDENTIALAll Access PointsChinese TranslationEnglish TranslationAdministrative Rules for Low-power Radio-Frequency DevicesArticle 12For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.ap1140getstart.fm Page 20 Monday, June 16, 2008 8:49 AM
21REVIEW DRAFT—CISCO CONFIDENTIALArticle 14The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. Chinese Translationap1140getstart.fm Page 21 Monday, June 16, 2008 8:49 AM
22REVIEW DRAFT—CISCO CONFIDENTIALEnglish TranslationLow-power Radio-frequency Devices Technical SpecificationsDeclaration of Conformity StatementsAll the Declaration of Conformity statements related to this product can be found at the following URL:http://www.ciscofax.comDeclaration of Conformity Statements for European Union CountriesThe Declaration of Conformity statement for the European Union countries is listed below:TO BE ADDED.8 Configuring Option 43 This section contains a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweight access points. For other DHCP server implementations, consult their product documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface.4.7 Unlicensed National Information Infrastructure4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations.4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manualap1140getstart.fm Page 22 Monday, June 16, 2008 8:49 AM
23REVIEW DRAFT—CISCO CONFIDENTIALNote DHCP Option 43 is limited to one access point type per DHCP pool. You must configure a separate DHCP pool for each access point type.The 1140 series access point uses the type-length-value (TLV) format for DHCP Option 43. DHCP servers must be programmed to return the option based on the access point’s DHCP Vendor Class Identifier (VCI) string (DHCP Option 60). The VCI string for the 1140 series access point is TBDThe format of the TLV block is listed below: • Type: 0xf1 (decimal 241) • Length: Number of controller IP addresses * 4 • Value: List of WLC management interfaces To configure DHCP Option 43 for the 1140 series access point in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS CLI. Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. A DHCP scope example is as follows: ip dhcp pool <pool name> network <IP Network> <Netmask> default-router <Default router> dns-server <DNS Server> Where:<pool name> is the name of the DHCP pool, such as AP1140<IP Network> is the network IP address where the controller resides, such as 10.0.15.1<Netmask> is the subnet mask, such as 255.255.255.0<Default router> is the IP address of the default router, such as 10.0.0.1<DNS Server> is the IP address of the DNS server, such as 10.0.10.2Step 3 Add the option 60 line using the following syntax: option 60 ascii “VCI string” For the VCI string, “TBD”. The quotation marks must be included. Step 4 Add the option 43 line using the following syntax: option 43 hex <hex string> The hex string is assembled by concatenating the TLV values shown below: ap1140getstart.fm Page 23 Monday, June 16, 2008 8:49 AM
24REVIEW DRAFT—CISCO CONFIDENTIALType + Length + Value Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex. For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is listed below: option 43 hex f1080a7e7e020a7f7f02 ==== ADDITIONAL INFO TO BE ADDED =====9 Access Point SpecificationsTable 2 lists the technical specifications for the 1140 series access point.Ta b l e 2 Access Point Specifications Category SpecificationDimensions (LxWxD) 8.68 x 8.68 x 1.84 in. (22.04 x 22.04 x 4.67 cm) Weight 1.9 lbs (0.86 kg)Operating temperature 32 to 104 degrees F (0 to –40 degrees C)Storage temperature –22 to 185 degrees F (–30 to 85 degrees C)Humidity 10% to 90% (noncondensing)Antenna (TBD)Compliance The 1140 series access point complies with UL 2043 for products installed in a building’s environmental air handling spaces, such as above suspended ceilings.ap1140getstart.fm Page 24 Monday, June 16, 2008 8:49 AM
25REVIEW DRAFT—CISCO CONFIDENTIALSafety UL1950 CSA C22.2, No. 60950-00 UL 60950 Third Edition IEC 60950 Second Edition, including Amendments 1-4, with all national deviations EN 60950:1992, including Amendments 1-4 UL 2043 (Plenum rating)EMI and Susceptibility FCC Part 15.07 and 15.109 Class B ICES-003 Class B (Canada) EN 55022 Class B, 2000 version (Telecommunications Port Conducted Emissions EN 55024 AS/NZS 3548 Class B VCCI Class BRadio FCC Part 15.247 Canada RSS-139-1, RSS-210 Japan Telec 33B EN 330.328 EN 301.489 FCC Bulletin OET-65C Industry Canada RSS-102Table 2 Access Point Specifications (continued)Category Specificationap1140getstart.fm Page 25 Monday, June 16, 2008 8:49 AM
26REVIEW DRAFT—CISCO CONFIDENTIALTable 3 lists the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the –A regulatory domain for a 2.4-GHz radio with up to 10-dBi antennas.Ta b l e 3 Channels and Maximum Conducted Power in the –A Regulatory Domain with up to 4-dBi Antennas Maximum Conducted Power Levels (dBm) in the –A Regulatory Domain for the 2.4-GHz Radio with up to 4-dBi AntennasFreq(MHz)Center Channel802.11b Single Antenna 1 to 11 Mbps802.11g Single Antenna 6 to 54 MbpsHT-20 MHz Dual Antennas M0 to M1511. M0 to M15 corresponds to the Modulaton and Coding Schemes (MCS0 to MCS15). The MCS settings determine the number of spatial streams, the modulation, the coding rate, and the data rate values.HT-40 MHz Dual Antennas M0 to M15120 MHz40 MHz Tx A Tx BTotal Pwr Tx A Tx BTotal Pwr Tx A Tx BTotal Power Tx A Tx BTotal Pwr2412 1 3 19 OFF 19 16 OFF 16 14 14 17 14 14 172417 2 4 20 OFF 20 17 OFF 17 16 16 19 15 15 182422 3 5 20 OFF 20 17 OFF 17 17 17 20 12 12 152427 4 6 20 OFF 20 17 OFF 17 17 17 20 15 15 182432 53, 7 20 OFF 20 17 OFF 17 17 17 20 14 14 172437 64, 8 23 OFF 23 17 OFF 17 17 17 20 15 15 182442 75, 9 20 OFF 20 17 OFF 17 17 17 20 15 15 182447 86, 1020 OFF 20 17 OFF 17 17 17 20 15 15 182452 97, 1120 OFF 20 17 OFF 17 16 16 19 12 12 152457 10 819 OFF 19 16 OFF 16 15 15 18 15 15 182462 11 918 OFF 18 14 OFF 14 12 12 15 14 14 172467 – – – – – – – – – – – – – –2472 – – – – – – – – – – – – – –2484 – – – – – – – – – – – – – –ap1140getstart.fm Page 26 Monday, June 16, 2008 8:49 AM
27REVIEW DRAFT—CISCO CONFIDENTIALTable 4 lists the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the –A regulatory domain for a 5-GHz radio with up to 6-dBi antennas.Ta b l e 4 Channels and Maximum Conducted Power in the –A Regulatory Domain with up to 3-dBi Antennas Maximum Conducted Power Levels (dBm) in the –A Regulatory Domain for the 5-GHz Radio with up to 3-dBi AntennasChannel IDFreq(MHz)802.11a Single Antenna 6 to 54 MbpsHT-20 MHz Dual Antennas M0 to M151Duplicate (2x20 MHz) Single Antennas 6 MbpsHT-40 MHz Dual Antennas M0 to M151Tx ATx BTotal PwrTx ATx BTotal PwrTx A – –Tx ATx BTotal Pwr5150-5250 MHz36 5180 14 OFF 14 11 11 14 13 – – 14 14 1740 5200 14 OFF 14 11 11 14 13 – – 14 14 1744 5220 14 OFF 14 11 11 14 13 – – 14 14 1748 5240 14 OFF 14 11 11 14 13 – – 14 14 175250 to 5350 MHz52 5260 17 OFF 17 17 17 20 17 – – 17 17 2056 5280 17 OFF 17 17 17 20 17 – – 17 17 2060 5300 17 OFF 17 17 17 20 13 – – 14 14 1764 5320 17 OFF 17 16 16 19 13 – – 14 14 175470 to 5725 MHz100 5500 17 OFF 17 17 17 20 14 – – 14 14 17104 5520 17 OFF 17 17 17 20 14 – – 14 14 17108 5540 17 OFF 17 17 17 20 17 – – 17 17 20112 5560 17 OFF 17 17 17 20 17 – – 17 17 20116 5580 17 OFF 17 17 17 20 – – – – – –120 5600 – – – – – – – – – – – –124 5620 – – – – – – – – – – – –128 5640 – – – – – – – – – – – –132 5660 17 OFF 17 17 17 20 17 – – 17 17 20ap1140getstart.fm Page 27 Monday, June 16, 2008 8:49 AM
28REVIEW DRAFT—CISCO CONFIDENTIALNote For additional information on the maximum power and the channels allowed in your regulatory domain, refer to the Channels and Maximum Power Settings for Cisco Aironet Autonomous Access Points and Bridges or the Channels and Maximum Power Settings for Cisco Aironet Lightweight Access Points.136 5680 17 OFF 17 17 17 20 17 – – 17 17 20140 5700 17 OFF 17 17 17 20 – – – – – –5725 to 5850 MHz149 5745 17 OFF 17 17 17 20 17 – – 17 17 20153 5765 17 OFF 17 17 17 20 17 – – 17 17 20157 5785 17 OFF 17 17 17 20 17 – – 17 17 20161 5805 17 OFF 17 17 17 20 17 – – 17 17 20165 5825 17 OFF 17 17 17 20 – – – – – –1. M0 to M15 corresponds to the Modulaton and Coding Schemes (MCS0 to MCS15). The MCS settings determine the number of spatial streams, the modulation, the coding rate, and the data rate values.Table 4 Channels and Maximum Conducted Power in the –A Regulatory Domain with up to 3-dBi Antennas (continued)Maximum Conducted Power Levels (dBm) in the –A Regulatory Domain for the 5-GHz Radio with up to 3-dBi AntennasChannel IDFreq(MHz)802.11a Single Antenna 6 to 54 MbpsHT-20 MHz Dual Antennas M0 to M151Duplicate (2x20 MHz) Single Antennas 6 MbpsHT-40 MHz Dual Antennas M0 to M151Tx ATx BTotal PwrTx ATx BTotal PwrTx A– –Tx ATx BTotal Pwrap1140getstart.fm Page 28 Monday, June 16, 2008 8:49 AM

Navigation menu