Cisco Systems RAN201 Wireless-N Home ADSL2 + Modem Router User Manual

Cisco Systems Inc Wireless-N Home ADSL2 + Modem Router

User manual

USER GUIDEModels: RAN201Wireless-N Home ADSL2 + Modem Router
About This GuideiAbout This GuideIcon DescriptionsWhile reading through the User Guide you may seevarious icons that call attention to specific items. Below isa description of these icons:NOTE: This check mark indicates that there isa note of interest and is something that youshould pay special attention to while using theproduct.WARNING: This exclamation point indicatesthat there is a caution or warning of potentialrisk of bodily injury and/or it is something thatcould damage your property or product.WEB: This globe icon indicates a noteworthywebsite address or e-mail address.Online ResourcesWebsite addresses in this document are listed withouthttp:// in front of the address because most current webbrowsers do not require it. If you use an older web browser,you may have to addhttp://in front of the web address.Resource WebsiteLinksys www.linksysbycisco.comLinksysInternational www.linksysbycisco.com/internationalGlossary www.linksysbycisco.com/glossaryNetwork Securitywww.linksysbycisco.com/securityWeb TechnicalSupportwww.linksysbycisco.com/supportCopyright and TrademarksLinksys, Cisco and the Cisco Logoare registered trademarks ortrademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certainother countries. Other brands and productnames are trademarks or registeredtrademarks of their respective holders.Copyright © 2009 Cisco Systems, Inc. All rights reserved.
Table of ContentsiiChapter 1: Product Overview 1Front Panel.................................................. 1Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Placement Positions ............................................ 2Chapter 2: Wireless Security Checklist 3General Network Security Guidelines ................................. 3Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Chapter 3: Advanced Conguration 4How to Access the Utility......................................... 4Using the Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4List of Screens in the Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Setup Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Wireless Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Storage Tab (WAG320N Only) ...................................... 5Security Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Access Restrictions Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Applications & Gaming Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Administration Tab............................................. 6Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Appendix A:Troubleshooting 8Appendix B:Specications 9RRAN201 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Appendix C:Regulatory Information 11European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18United States of America.........................................18Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Chapter 1 Product Overview1Chapter 1: Product OverviewThank you for choosing the Wireless ADSL2+ ModemRouter. This device lets you access the Internet via awireless connection or through one of its four switchedports. You can also use it to share resources such ascomputers, printers and files. A variety of security features,such as WPA2™security, a Stateful Packet Inspection (SPI)firewall and NAT technology, help to protect your dataand your privacy while online. Configuration is easy usingthe provided browser-based utility.Front PanelPower(RARRN201: Green/Amber; WAG160N v2 and WAG320N: Green/Red)The Power LEDis continuously lit green while the device ispowered on. The LED is lit amber (RARRN201)or red (WAG160N v2 and WAG320N) if a POST (Power On Self Test) failure or device malfunctionoccurs.Ethernet 1-4(Green)These numbered LEDs, one for each of the numbered ports on the Modem Router’s back panel, serve two purposes.If the LED is continuously lit, the Modem Router issuccessfully connected to a device through thatport. It flashes to indicate network activity overthat port.NOTE: The Ethernet 1 LED is lit amberwhen the WAN link is established on thatport.Wi-Fi Protected Setup™ Button(RARRN201:Green/Amber; WAG160N v2 and WAG320N:Green) Press this button to have Wi-Fi ProtectedSetup™search for your Wi-Fi ProtectedSetup™-supported wireless device. The LED iscontinuously lit green when a Wi-Fi ProtectedSetup™ connection is successfully established.The LED blinks slowly while Wi-Fi ProtectedSetup™ is setting up a connection, and is lit amber(RARRN201) or blinks rapidly (WAG160Nv2 andWAG320N) if an error occurs. The LED is off whenWi-Fi Protected Setup™ is idle.NOTE:Wi-Fi Protected Setup™ is a featurethat makes it easy to configure your wireless network and its security settings.USB (WAG320N only)(Green)The USB LEDlights up when a USB device isconnected to the Modem Router through the USB port.Wireless(Green)The Wireless LED lights upwhen the wirelessfeature is enabled. It flashes when the Modem Router is actively sending orreceiving data over the network.DSL(Green)The DSL LED lights up whenever there is asuccessful DSL connection. The LED flashes green while the Modem Router isestablishing the ADSL connection.Internet The Internet LED lights upgreen and stays on when a connection is madethrough the Internet port. It flashes to indicatenetwork activity over the Internet port. The LEDis lit red when an authentication error occurs.Back PanelDSLThe DSL port connects to the ADSL line.Ethernet 4, 3, 2, 1 The Ethernet ports (4, 3, 2, 1)connect the Modem Router to wired computersand other Ethernet network devices.NOTE: The Ethernet 1 port can also be configured as the WANport. To do this, access the Web-based utility (refer to“Chapter 3: pAdvanced Configuration” on page 4gpg),then select the Setup > Ethernet tab.USB (WAG320N only) The USB port connects the Modem Router to a hard drive or flash-based USB storage device.ResetThere are two ways to reset the ModemRouter’s factory defaults. Either press andhold the Reset button for approximately fiveseconds, or restore the defaults from theAdministration>Factory Defaults screen of theModem Router’s web-based utility.PowerThe Power port is where you will connectthe power adapter.On/Off Button Press the On/Off button to turnpower to the device on or off.
Chapter 1 Product Overview2Follow these instructions:1.Determine where youwant to mount the device. Makesure that the wall you use is smooth, flat, dry, andsturdy. Also make sure the location is within reach of an electrical outlet. 2.Drill two holes into the wall. Make sure the holes are 152 mm (6 inches) apart.3.Insert a screw into each hole and leave 3 mm (0,12 inches) of its head exposed.4.Maneuver the device so the wall-mount slots line upwith the two screws.5.Place the wall-mount slotsover the screws and slidethe device down until the screws fit snugly into thewall-mount slots.Placement PositionsThere are two ways to physically install the device. Thefirst way is to place the device horizontally on a surface.The second way is to mount the device on a wall.The best place for the device is usually at the center of your wireless network, within range of all of your wirelessdevices.Horizontal PlacementThe device has four rubber feet on its bottom panel. Placethe device on a level surface near an electrical outlet.Wall-Mounting PlacementThe device has two wall-mount slots on its bottompanel. The distance between the slots is 152 mm (6 inches).Two screws are needed to mount the device.Suggested Mounting Hardware2,5-3,0 mm4-5 mm 1-1,5 mm†Note: Mounting hardware illustrations are not true to scale.NOTE: Cisco is not responsible for damagesincurred by insecure wall-mounting hardware.152 mmWall Mounting Template
Chapter 2 Wireless Security Checklist3Chapter 2: Wireless Security ChecklistWireless networks are convenient and easy to install, sohomes with high-speed Internet access are adopting themat a rapid pace. Because wireless networking operates bysending information over radio waves, it can be morevulnerable to intruders than a traditional wired network.Like signals from your cellular or cordless phones, signalsfrom your wireless network can also be intercepted. Sinceyou cannot physically prevent someone from connectingto your wireless network, you need to take some additionalsteps to keep your network secure.1. Change the default wireless network name or SSIDWireless devices have a default wireless network nameor Service Set Identifier (SSID) set by the factory. This isthe name of your wireless network, and can be up to 32characters in length. Linksys by Cisco wireless productsuselinksys as the default wireless network name. Youshould change the wireless network name to somethingunique to distinguish your wireless network from otherwireless networks that may exist around you, but do notuse personal information (such as your Social Securitynumber) because this information may be available foranyone to see when browsing for wireless networks.2. Change the default passwordFor wireless products such as access points, routers, andmodem routers, you will be asked for a password whenyou want to change their settings. These devices have adefault password set by the factory. The default passwordisadmin. Hackers know these defaults and may try touse them to access your wireless device and change yournetwork settings. To thwart any unauthorized changes,customize the device’s password so it will be hard toguess.3. Enable MAC address filteringLinksys by Cisco routers and modem routers give youthe ability to enable Media Access Control (MAC) addressfiltering. The MAC address is a unique series of numbersand letters assigned to every networking device. WithMAC address filtering enabled, wireless network accessis provided solely for wireless devices with specific MACaddresses. For example, you can specify the MAC addressof each computer in your home so that only thosecomputers can access your wireless network.4. Enable encryptionEncryption protects data transmitted over a wirelessnetwork. Wi-Fi Protected Access™ (WPA™/WPA2™) and Wired Equivalency Privacy (WEP) offer different levels of security for wireless communication.A network encrypted with WPA™/WPA2™ is more secure than a network encrypted with WEP, because WPA™/WPA2™ uses dynamic key encryption. To protectthe information as it passes over the airwaves, you shouldenable the highest level of encryption supported by yournetwork equipment.WEP is an older encryption standard and may be theonly option available on some older devices that do notsupport WPA™.General Network Security GuidelinesWireless network security is useless if the underlyingnetwork is not secure.sPassword protect all computers on the network andindividually password protect sensitive files.sChange passwords on a regular basis.sInstall anti-virus software and personal firewallsoftware.sDisable file sharing (peer-to-peer). Some applicationsmay open file sharing without your consent and/orknowledge.Additional Security TipssKeep wireless routers, access points, or modem routersaway from exterior walls and windows.sTurn wireless routers, access points, or modem routersoff when they are not being used (at night, duringvacations).sUse strong passphrases that are at least eight charactersin length. Combine letters and numbers to avoid usingstandard words that can be found in the dictionary.WEB: For more information on wireless security,visitwww.linksysbycisco.com/security
Chapter 3 Advanced Configuration4Chapter 3:Advanced ConfigurationAfter you finish running the Setup Wizard on the SetupCD-ROM, the device is ready for use. To change the device’sadvanced settings, access the Configuration Utility via aweb browser on a computer connected to the device.NOTE FOR USERS IN NEW ZEALAND: Refer tothe Note in Setup > Basic Setuppp,page 5pg forsetup instructions specific to your country.How to Access the UtilityLaunch the web browser on your computer, and enter thedevice’s default IP address,192.168.1.1, in the Addressfield. Then, pressEnter.A login screen appears. Use the default user name andpassword,admin, unless you changed them when youran the Setup Wizard. (You can set a new user name andpassword from the Administration tab’sManagementscreen.) Click OKto continue.KLoginIf you are unable to log in, press the Reset button on theback panel for at least 5 seconds, then wait for the deviceto reset and try again.Using the UtilityImmediately after login, the Basic Setup screen appears.Near the top of the screen is a bar with selectable tabs.Use these tabs to navigate within the Utility. Theprimarytabs indicate the Utility’s main configuration categories.Each primary tab has one or more secondary tabs thatprovide access to the primary tab’s configuration screens.Setup Wireless Storage Security Access RestrictionsApplications & Gaming Administration Status Basic Setup Ethernet DDNS MAC Address Clone Advanced RoutingNavigation TabsTo access a screen, click the appropriate primary tab,then click the appropriate secondary tab. The screen willappear, with its primary and secondary tabs highlighted.List of Screens in the UtilityThe screens are organized hierarchically as listed below.(Some screens may not apply to all models.)Setup TabSetup > Basic SetupSetup > EthernetSetup > DDNSSetup > MAC Address CloneSetup > Advanced RoutingWireless TabWireless > Basic Wireless SettingsWireless > Wireless SecurityWireless > Wireless MAC FilterWireless > Advanced Wireless SettingsStorage Tab (WAG320N Only)Storage > Disk ManagementStorage > Shared FolderStorage > AdministrationStorage > Media ServerSecurity TabSecurity > FirewallSecurity > VPN PassthroughAccess Restrictions TabAccess Restrictions > Internet Access PolicyApplications & Gaming TabApplications & Gaming > Single Port ForwardingApplications & Gaming > Port Range ForwardingApplications & Gaming > Port Range TriggeringApplications & Gaming > DMZApplications & Gaming > QoSAdministration TabAdministration > ManagementAdministration > ReportingAdministration > DiagnosticsAdministration > Back Up & RestoreAdministration > Factory DefaultsAdministration > Firmware UpgradeAdministration > LanguageStatus TabStatus > Modem RouterStatus > Local NetworkStatus > Wireless NetworkStatus > DSL ConnectionPrimary TabsSecondary Tabs
Chapter 3 Advanced Configuration5Setup TabThe Setup tab provides the device’s basic setup functions.For detailed information on the Setup tab, refer to theUtility’s online help pages.Setup > Basic SetupThe Basic Setup screen allows you to change the device’sgeneral settings. The following connection types(encapsulations) are available:sRFC2364PPPoAsRFC2516PPPoEsRFC2684RoutedsIPoAsRFC2684 Bridged-Dynamic IP AddresssRFC2684 Bridged-Static IP AddresssBridge Mode OnlyNOTE FOR USERS IN NEW ZEALAND:To set upthe device, follow these instructions:1.Access theSetup > Basic Setupscreen.2.Select RFC 2364 PPPoAfrom theEncapsulation drop-down menu.3.For the Virtual Circuit ID, enter0 for the VPIand100 for the VCI.4.Select VC for Multiplexing.5.Select Multimode from theDSL Modulationdrop-down menu.6.Enter your User Nameand Password detailsfrom your ISP.7.ClickSave Settings.Setup > EthernetThe Ethernetscreen allows you to configure the device’stEthernet settings. It also allows you to set up the firstEthernet port as a WAN port.Setup > DDNSThe DDNS screen allows you to assign a fixed host anddomain name to a network computer that has beenassigned a dynamic Internet IP address. This is usefulwhen you are hosting your own website, FTP server, orother server behind the device.Setup > MAC Address CloneSome service providers require you to register a MACaddress in order to access the Internet. TheMAC AddressClonescreen lets you use the MAC address of a device thathas already been registered with your service provider, bycopying that MAC address to the device.Setup > Advanced RoutingThe Advanced Routingscreen allows you to configure thedevice’s advanced routing functions, such as operatingmode, dynamic mode, and static routing.Wireless TabThe Wireless tab allows you to configure the device’swireless functions.For detailed information on the Wireless tab, refer to theUtility’s online help pages.Wireless > Basic Wireless SettingsThe Basic Wireless Settingsscreen allows you to set up anetwork with Wi-Fi Protected Setup™, change the radioband, select the network mode, change the wirelessnetwork name (SSID), change the wireless channel anddisable the SSID broadcast.Wireless > Wireless SecurityThe Wireless Securityscreen allows you to configure theysecurity of your wireless network(s). It allows you to selectfrom a number of security modes, such as WPA2.Wireless > Wireless MAC FilterThe Wireless MAC Filter screen allows you to control (block or allow) Internet access by individual devices on yourwireless network by specifying their MAC addresses.Wireless > Advanced Wireless SettingsThe Advanced Wireless Settingsscreen allows you toconfigure the device’s advanced wireless functions.Storage > Disk ManagementThe Disk Managementscreen displays information on antattached USB storage device, and allows you to performbasic management functions on the device. It alsoprovides information on the attached USB disk, allows fora blank disk to be formatted, and enables safe removal of the attached disk.Storage > Shared FolderThe Shared Folderscreen allows you to manage the sharedrfolders on an external USB storage device. A shared folder
Chapter 3 Advanced Configuration6is a directory on the device that a user can access throughthe network.Storage > AdministrationThe Administrationscreen allows you to configure basicstorage settings and manage the device’s users.Storage > Media ServerThe Media Serverscreen allows you to configure therdevice’s built-in media server, and to select the folders toscan for content.Security TabThe Security tab allows you to enhance the security of your network. For detailed information on the Security tab, refer to theUtility’s online help pages.Security > FirewallThe Firewall screen allows you to configure a firewall thatlcan filter out various types of unwanted traffic on thedevice’s local network.Security > VPN PassthroughThe VPN Passthroughscreen allows you to configure thedevice’s VPN passthrough feature. This feature lets VPNtunnels using the IPSec, L2TP, or PPTP protocols to passthrough the device’s firewall.Access Restrictions TabThe Access Restrictions tab allows you to configurethe Internet access restrictions for each device in yournetwork.For detailed information on the Access Restrictions tab,refer to the Utility’s online help pages.Access Restrictions > Internet Access PolicyThe Internet Access Policy screen allows you to definepolicies that are used to block or allow specific kindsof Internet usage and traffic, such as Internet access,designated applications, websites, and inbound trafficduring specific days and times, and for a specified list of devices in your network.Applications & Gaming TabThe Applications & Gaming tab allows you to configurefunctions such as port forwarding and quality of servicethat may be necessary for special applications such ashosting web servers, ftp servers, and e-mail servers on onyour network, or other specialized internet applicationssuch as videoconferencing or online gaming.For detailed information on the Applications & Gamingtab, refer to the Utility’s online help pages.Applications & Gaming > Single Port ForwardingThe Single Port Forwarding screen allows you to set up port forwarding for a single port. You should assign staticIP addresses to the destination computers before you usethis feature.Applications & Gaming > Port Range ForwardingThe Port Range Forwardingscreen allows you to set upport forwarding for a range of ports. You should assignstatic IP addresses to the destination computers beforeyou use this feature.Applications & Gaming > Port Range TriggeringThe Port Range Triggering screen allows you to set up porttriggering. When port triggering is configured, the devicewatches for specified port numbers in outgoing data.When a match is found, the device records the sendingcomputer’s IP address so that when the requested datareturns, it can be sent to the proper computer.Applications & Gaming > DMZThe DMZscreen allows you to expose one network userto the Internet for use of a special-purpose service suchas Internet gaming or video conferencing. DMZ hostingforwards all the ports at the same time to one computer.You should assign static IP addresses to the destinationcomputers before you use this feature.Applications & Gaming > QoSThe QoSscreen allows you to specify priorities for differenttypes of traffic. Lower priority traffic will be slowed downto allow greater throughput or less delay for high prioritytraffic.Administration TabThe Administration tab allows you to configure the device’sadministrative functions.For detailed information on the Administration tab, referto the Utility’s online help pages.Administration > ManagementThe Managementscreen allows you to manage specificfunctions for access and security.
Chapter 3 Advanced Configuration7NOTE ON CISCO WEB ASSISTANT OPTION (not on all models): If you see an “error code404” message (indicating that you entered aninvalid web address), the Cisco Web Assistantwill appear and automatically run a searchbased on the keywords in the web address. Thisfeature can be enabled or disabled from thisscreen.NOTE ON TREND MICRO OPTION (not on all models): Trend Micro ProtectLink Gatewayis a hosted security service that stops spamand filters URLS to prevent unwanted contentfrom passing through your router. The EmailProtection is the hosted messaging securitysolution provided by Trend Micro InterScanMessaging Hosted Security (IMHS). This featurecan be enabled or disabled from this screen.Administration > ReportingThe Reporting screen allows you to configure system eventlogging and to configure sending of e-mail alerts when aDenial of Service attack is detected.Administration > DiagnosticsThe Diagnostics screen allows you to perform a ping testto check the status of your Internet connection.Administration > Back Up & RestoreThe Back Up & Restore screen allows you to back up andrestore the configuration settings of your device.Administration > Factory DefaultsThe Factory Defaultsscreen allows you to restore thefactory defaults of the device. All savings you have savedwill be lostNOTE: Restoring the factory defaults causes allsettings you have previously saved to be lost.Administration > Firmware UpgradeThe Firmware Upgrade screen allows you to upgrade the device’s firmware.Administration > LanguageThe Languagescreen allows you to select an availablelanguage for the utility.Status TabThe Status tab allows you to display status information.For detailed information on the Status tab, refer to theUtility’s online help pages.Status > Modem RouterThe Modem Router screen displays information about thedevice and its current settings. The on-screen informationwill vary depending on the Internet Connection Type youuse.Status > Local NetworkThe Local Network screen displays the status of your LocalArea Network.Status > Wireless NetworkThe Wireless Network screen displays some basicinformation about the wireless network of the device.Status > DSL ConnectionThe DSL Connectionscreen displays the status of your DSLconnection.
Appendix A Troubleshooting8Appendix A: TroubleshootingYour computer cannot connect to the Internet.Follow the instructions until your computer can connectto the Internet:sMake sure that the Modem Router is powered on. ThePower LED should be green and not flashing.sIf the Power LED is flashing, then power off all of your network devices, including the Modem Routerand computers. Then power on each device in thefollowing order:1.Modem Router2.ComputersCheck the LEDs on the device’s front panel. Make surethe Power, DSL, and at least one of the numberedEthernet LEDs are lit. If they are not, then check the cable connections. The computer should beconnected to one of the Ethernet ports numbered1-4 on the device, and the device’s DSL port must beconnected to the ADSL line.When you double-click the web browser, you areprompted for a user name and password. If you want toget rid of the prompt, follow these instructions.Launch the web browser and perform the following steps(these steps are specific to Internet Explorer but are similarfor other browsers):1.Select Tools> Internet Options.2.Click theConnections tab.3.SelectNever dial a connection.4.ClickOK.You are using a static IP address and cannot connect.Refer to Windows Help and change your Internet Protocol(TCP/IP) Properties to Obtain an IP address automatically.The computer cannot connect wirelessly to the network.Make sure the wireless network name or SSID is the sameon both the computer and the device. If you have enabledwireless security, then make sure the same securitymethod and key are used by both the computer and thedevice.You need to modify the basic settings on thedeviceRouter.Run the Setup Wizard on the Setup CD-ROM.You need to modify the advanced settings on thedevice.Open the web browser (for example, Internet Explorer orFirefox), and enter the device’s IP address in the addressfield (the default IP address is 192.168.1.1). When prompted, complete theUser nameand Passwordfieldsd(the default user name and password isadmin). Click theappropriate tab to change the settingsWEB: If your questions are not addressed here, refer to the website, www.linksysbycisco.com/support
Appendix B Specifications9Appendix B: SpecificationsWAG120N RAN201StandardsWLAN: 802.11n draft 2.0, 802.11g,802.11bEthernet: 802.3, 802.3uADSL: T1.413i2, G.992.1 (G.DMT),G.992.2 (G.Lite), G.992.3 (ADSL2),G.992.5 (ADSL2+) for Annex A, B, M, L, U-R2 for Annex BPortsDSL, Ethernet (1-4), PowerButtonsOn/O, Reset, Wi-Fi Protected Setup™LEDs Power, Ethernet (1-4), Security,Wireless, DSL, InternetCabling TypeCAT5, RJ-11 (for Annex A),RJ-45 (for Annex B)Antennas2 InternalModulationsTransmit PowerReceive Sensitivity-80 dBm (typical) @ 11 Mbps-70 dBm (typical) @ 54 Mbps-61 dBm (typical) @ 130 Mbps-61 dBm (typical) @ 270 MbpsAntenna GainSecurity FeaturesWPA2™/WPA™ Personal and Enterprise;128, 64 bits WEP;MAC Address Filtering;SPI FirewallOS RequirementsWindows XP, Vista, or Vista 64-bit (to run the edition with latest updates (for Setup CD) Network Magic and Setup Wizard);Mac OS X 10.4 or higher (for Setup Wizard)EnvironmentalDimensions202 x 34 x 160 mm (8,0” x 1,3” x 6,3”)Weight362 g (12,8 oz)Power12VDC, 1ACerticationFCC, CE, Telepermit, K.21, UL, CB,Wi-Fi (802.11b/g), WPA™, WPA2™,WMM, Wi-Fi Protected Setup™Operating Temp.0 to 40°C (32 to 104°F)Storage Temp. -20 to 70°C (-4 to 158°F)OperatingHumidity10 to 85% NoncondensingStorage Humidity5 to 90% NoncondensingIEEE 802.11b mode:19.83 dBmIEEE 802.11g mode:17.45 dBmdraft 802.11n standard-20MHz Channel mode:18.70 dBmdraft 802.11n Wide-40MHz Channel mode:15.47 dBmIEEE 802.11b mode:DSSSIEEE 802.11g mode:OFDMdraft 802.11n Standard-20MHz Channel mode:OFDMdraft 802.11n Wide-40MHz Channel mode:OFDMPCB Antenna Gain:1.5 dBi PIFA Antenna Gain:2 dBi
Appendix C Regulatory Information11Appendix C: Regulatory InformationEuropean UnionThe following information applies if you use the productwithin the European Union.Declaration of Conformity with Regard to EUDirective 1999/5/EC (R&TTE Directive) Compliance Information for 2,4-GHz WirelessProducts Relevant to the EU and Other CountriesFollowing the EU Directive 1999/5/EC (R&TTE Directive)Български [Bulgarian]Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС.Česky [Czech]:Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.Dansk[Danish]:Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.Deutsch [German]:Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.Eesti [Estonian]:See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.English:This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español[Spanish]:Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.Ελληνική [Greek]:Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.Français [French]:Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.Íslenska [Icelandic]:Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.Italiano [Italian]:Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.Latviski [Latvian]:Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių[Lithuanian]:Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.Nederlands[Dutch]:Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.Malti [Maltese]:Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.Magyar[Hungarian]:Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.Norsk[Norwegian]:Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.Polski [Polish]:Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.Português [Portuguese]:Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.Română [Romanian]Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.Slovensko [Slovenian]:Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.Slovensky [Slovak]:Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC. Suomi[Finnish]:Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.Svenska [Swedish]:Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.
Appendix C Regulatory Information12For all products, the Declaration of Conformity (DofC) isavailable through one or more of these options:sA pdf file is included on the product’s CD.sA print copy is included with the product.sA pdf file is available on the product’s webpage. Visitwww.linksysbycisco.com/internationalyyandselect your country or region. Then select your product.If you need any other technical documentation, see the“Technical Documents on www.linksysbycisco.com/international” section, as shown later in this appendix.Non-Wireless Equipment (ADSL Modems/Gateways)The following standards were applied during theassessment of the product against the requirements of the Directive 1999/5/EC:sEMC: EN 55 022 and EN 55 024sSafety: EN 60950-1CE MarkingFor the Linksys products such as the ADSL modems/gateways, the following CE mark is added to theequipment.Wireless Equipment (Wireless-N/G/A/B Products)The following standards were applied during theassessment of the product against the requirements of the Directive 1999/5/EC:sRadio: EN 300 328 and/or EN 301 893 as applicablesEMC: EN 301 489-1, EN 301 489-17sSafety: EN 60950-1 and either EN 50385 or EN 50371For the Linksys Wireless-N, -G, -B, and/or -A products, thefollowing CE mark, and class 2 identifier are added to theequipment.National RestrictionsThis product may be used in all EU countries (and othercountries following the EU directive 1999/5/EC) withoutany limitation except for the countries mentioned below:Ce produit peut être utilisé dans tous les pays de l’UE (et danstous les pays ayant transposés la directive 1999/5/CE) sansaucune limitation, excepté pour les pays mentionnés ci-dessous:Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senzanessuna limitazione, eccetto per i paesi menzionati di seguito:Das Produkt kann in allen EU Staaten ohne Einschränkungeneingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Außnahme der folgendenaufgeführten Staaten:In the majority of the EU and other European countries,the 2,4-GHz bands have been made available forthe use of wireless local area networks (LANs). Later inthis document you will find an overview of countries inwhich additional restrictions or requirements or both areapplicable.The requirements for any country may evolve. Linksysrecommends that you check with the local authorities forthe latest status of their national regulations for both the2,4- GHz wireless LANs.The following countries have restrictions and/orrequirements in addition to those given in the tablelabeled “Overview of Regulatory Requirements for WirelessLANs”:FranceFor 2,4 GHz, the product should not be used outdoorsin the band 2454 - 2483,5 MHz. There are no restrictionswhen used in other parts of the 2,4 GHz band OR whenused indoors. Check http://www.arcep.fr/ppfor moredetails.Pour la bande 2,4 GHz, l’ équipement ne doit pas êtreutilisé en extérieur dans la bande 2454- 2483,5 MHz. Iln’y a aucune restriction pour son utilisation dans d’autresparties de la bande des 2,4 GHz ainsi que pour uneutilisation en intérieur. Consultezhttp://www.arcep.fr/pppour de plus amples détails.
Appendix C Regulatory Information13LatviaThe outdoor usage of the 2,4 GHz band requires anauthorization from the Electronic Communications Office.Please check http://www.esd.lvpfor more details.2,4 GHz frekveču joslas izmantošanai ārpus telpāmnepieciešama atļauja no Elektronisko sakaru direkcijas.Vairāk informācijas:http://www.esd.lvp.Notes: 1.Although Norway, Switzerland and Liechtenstein arenot EU member states, the EU Directive 1999/5/EC hasalso been implemented in those countries.2.The regulatory limits for maximum output power arespecified in EIRP. The EIRP level (in dBm) of a device canbe calculated by adding the gain of the antenna used(specified in dBi) to the output power available at theconnector (specified in dBm).Product Usage RestrictionsThis product is designed for indoor usage only. Outdoorusage is not recommended, unless otherwise noted.Outdoor usage may even be prohibited (see below).2,4 GHz RestrictionsThis product is designed for use with the standard, integralor dedicated (external) antenna(s) that is/are shippedtogether with the equipment. However, some applicationsmay require the antenna(s), if removable, to be separatedfrom the product and installed remotely from the deviceby using extension cables. For these applications, Linksysoffers an R SMA extension cable (AC9SMA) and an R-TNCextension cable (AC9TNC). Both of these cables are 9meters long and have a cable loss (attenuation) of 5 dB. Tocompensate for the attenuation, Linksys also offers highergain antennas, the HGA7S (with R-SMA connector) andHGA7T (with R-TNC connector). These antennas have again of 7 dBi and may only be used with either the R-SMAor R-TNC extension cable.Combinations of extension cables and antennas resultingin a radiated power level exceeding 20 dBm (100 mW)EIRP (2,4 GHz band) are illegal.Third-Party Software or FirmwareThe use of software or firmware not supported/providedby Linksys may result that the equipment is no longercompliant with the regulatory requirements.Technical Documents on www.linksysbycisco.com/internationalFollow these steps to access technical documents:1.Enterhttp://www.linksysbpyycisco.com/internationalyin your web browser.2.Select the country or region in which you live.3.Click theProductstab.4.Select the appropriate product category.5.Select the product sub-category, if necessary.6.Select the product.7.Select the type of documentation you want from the More Information section.The document will open in PDF format if you have Adobe Acrobat installed on your computer.NOTE: If you have questions regardingthe compliance of this product or youcannot find the information you need,please contact your local sales office or visit www.linksysbycisco.com/international
Appendix C Regulatory Information14User Information for Consumer Products Coveredby EU Directive 2002/96/EC on Waste Electric andElectronic Equipment (WEEE)This document contains important information for userswith regards to the proper disposal and recycling of Linksys products. Consumers are required to complywith this notice for all electronic products bearing thefollowing symbol:the European UnionEuropean Directive 2002/96/EC requires that the equipment bearing this symbol not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.Български (Bulgarian) - Информация относноопазването на околната среда за потребители вЕвропейския съюзЕвропейска директива 2002/96/EC изисква уредите, носещи този символ се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.Čeština (Czech) - Informace o ochraně životníhoprostředí pro zákazníky v zemích Evropské unieEvropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.Dansk (Danish) - Miljøinformation for kunder i EUEU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.Deutsch (German) - Umweltinformation für Kundeninnerhalb der Europäischen UnionDie Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
Appendix C Regulatory Information15Eesti (Estonian) - Keskkonnaalane informatsioonEuroopa Liidus asuvatele klientideleEuroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.Español (Spanish) - Información medioambiental paraclientes de la Unión EuropeaLa Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.Ελληνικά (Greek) - Στοιχεία περιβαλλοντικήςπροστασίας για πελάτες εντός της ΕυρωπαϊκήςΈνωσηςΣύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που φέρει αυτό το σύμβολο δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων, οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από το οποίο αγοράσατε το προϊόν.Français (French) - Informations environnementalespour les clients de l’Union européenneLa directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.Italiano (Italian) - Informazioni relative all’ambienteper i clienti residenti nell’Unione EuropeaLa direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.Latviešu valoda (Latvian) - Ekoloģiska informācijaklientiem Eiropas Savienības jurisdikcijāDirektīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīmeizmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.
Appendix C Regulatory Information16Lietuvškai (Lithuanian) - Aplinkosaugos informacija,skirta Europos Sąjungos vartotojamsEuropos direktyva 2002/96/EC numato, kad įrangos, kuri ir negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.Malti (Maltese) - Informazzjoni Ambjentali għalKlijenti fl-Unjoni EwropeaId-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-simbolujintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.Magyar (Hungarian) - Környezetvédelmi információ azeurópai uniós vásárlók számáraA 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.Nederlands (Dutch) - Milieu-informatie voor klantenin de Europese UnieDe Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.Norsk (Norwegian) - Miljøinformasjon for kunder i EUEU-direktiv 2002/96/EF krever at utstyr med følgende symbol sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.Polski (Polish) - Informacja dla klientów w UniiEuropejskiej o przepisach dotyczących ochronyśrodowiskaDyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.
Appendix C Regulatory Information17Português (Portuguese) - Informação ambiental paraclientes da União EuropeiaA Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.Română (Romanian) - Informaţii de mediu pentruclienţii din Uniunea EuropeanăDirectiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.Slovenčina (Slovak) - Informácie o ochrane životnéhoprostredia pre zákazníkov v Európskej úniiPodľa európskej smernice 2002/96/ES zariadenie s týmto symbolomlikvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.Slovenščina (Slovene) - Okoljske informacije zastranke v Evropski unijiEvropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo oddate na posebna zbirališča, ki jih določijo državne ustanove ali lokalne oblasti. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali trgovino, kjer ste izdelek kupili.Suomi (Finnish) - Ympäristöä koskevia tietoja EU-alueen asiakkailleEU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboliei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.Svenska (Swedish) - Miljöinformation för kunder iEuropeiska unionenDet europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.WEB: For additional information, please visitwww.linksysbycisco.com/international
Appendix C Regulatory Information18AustraliaThe following information applies if you use the productwithin Australia.Safety NoticeWARNING: To ensure compliance withexposure limits to radiofrequency fields, theantenna of the device should be no closer than20 cm from the body during use.New ZealandThe following information applies if you use the productwithin New Zealand.Telepermit StatementThe cabling between the phone port and the phone shallnot exceed 100 metres.PTC200 General WarningThe grant of a Telepermit for any item of terminalequipment indicates only that Telecom has acceptedthat the item complies with minimum conditions forconnection to its network. It indicates no endorsementof the product by Telecom, nor does it provide any sortof warranty. Above all, it provides no assurance that anyitem will work correctly in all respects with another itemof Telepermitted equipment of a different make or model,nor does it imply that any product is compatible with all of Telecom’s network services.Wireless Connectivity Security on Cisco-LinksysADSL2+ DevicesSetting up the security of the wireless connectionassociated with ADSL2+ device is the user’s responsibility.Telecom will take no responsibility for charges made touser’s accounts due to poorly organized wireless securityallowing unknown users to connect to the Internet via thisdevice. Do not complain to the Telecom Fault Service orJetstream Helpdesk should this occur.General Warning for Cisco-Linksys ADSL2+ Devices and ADSL2+ CapabilityThis device has been tested and found suitable to connectto the Telecom ADSL2+ capability. This indicates only thatTelecom has accepted that this device complies with thespectrum management plan for ADSL2+ on copper cableand with simple voiceband compatibility tests includedin PTC273. It does not indicate that this device is fullycompatible with all services accessed via the ADSL2+capability. Contact the supplier of the device whenissues occur. Do not call the Telecom Fault Service or theJetstream Helpdesk.Cisco-Linksys ADSL2+ Devices on Long LinesADSL2+ devices may not achieve the type of “high speed” operation expected when attached to a line that is longerthan intended by the ITU-T Rec. G.996.1 ADSL standardi.e. >3 km of 0.4mm cable or a shorter cable length withseveral tails or multiples. If the device is installed in suchconditions and does not give the expected “download” performance, then do not refer the matter to the TelecomFault Service or ADSL Helpdesk.United States of AmericaThe following information applies if you use the productwithin the United States of America.FCC StatementFCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different  from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for  help.
Appendix C Regulatory Information19This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter. IEEE802.11b or 802.11g operation of this product in the USA isfirmware-limited to channels 1 through 11.FCC Part 68 StatementThis equipment complies with Part 68 of the FCC Rules. Alabel is attached to the equipment that contains, amongother information, its FCC registration number and ringerequivalence number. If requested, this information mustbe provided to the telephone company.This equipment uses the following USOC Jack: RJ-11.An FCC compliant telephone cord and modular plugis provided with this equipment. This equipment isdesigned to be connected to the telephone network orpremises wiring using a compatible modular jack, whichis FCC Part 68 compliant. Connection to the telephonenetwork should be made by using the standard modulartelephone jack.The REN is useful to determine the quantity of devicesthat may be connected to the telephone line and still haveall of those devices ring when your telephone number iscalled. In most, but not all areas, the sum of RENs shouldnot exceed 5. To be certain of the number of devices thatmay be connected to the line, as determined by the totalRENs, contact the telephone company to determine themaximum REN for the calling area.If this equipment causes harm to the telephone network,the telephone company may discontinue your servicetemporarily. If advance notice is not practical, thetelephone company will notify the customer as soon aspossible. Also, you will be advised of your right to file acomplaint with the FCC if you believe it is necessary.The telephone company may make changes in itsfacilities, equipment, operations, or procedures that couldaffect the operation of the equipment. If this happens, thetelephone company will provide advance notice in orderfor you to make the necessary modifications in order tomaintain uninterrupted service.In the event this equipment should fail to operateproperly, disconnect the unit from the telephone line.Try using another FCC approved device in the sametelephone jack. If the trouble persists, call the telephonecompany repair service bureau. If the trouble does notpersist and appears to be with this unit, disconnect theunit from the telephone line and discontinue use of theunit until it is repaired. Please note that the telephonecompany may ask that you disconnect the equipmentfrom the telephone network until the problem has beencorrected or until you are sure that the equipment is notmalfunctioning. The user must use the accessories andcables supplied by the manufacturer to get optimumperformance from the product.No repairs may be done by the customer. If trouble isexperienced with this equipment, please contact yourauthorized support provider for repair and warrantyinformation. If the trouble is causing harm to thetelephone network, the telephone company may requestyou remove the equipment from the network until theproblem is resolved. This equipment cannot be used ontelephone company provided coin service. Connection toParty Line Service is subject to state tariffs.Safety NoticesWARNING: To reduce the risk of fire, use onlyNo.26 AWG or larger telecommunication linecord.WARNING: Do not use this product near water,for example, in a wet basement or near aswimming pool.WARNING: Avoid using this product during anelectrical storm. There may be a remote risk of electric shock from lightning.WARNING: This equipment will be inoperablewhen main power fails.WARNING: To ensure compliance withexplosure limits to radiofrequency fields, theantenna of the device should be no closer than20 cm from the body during use.
Appendix C Regulatory Information20Avis d’Industrie Canada concernant l’exposition aux radio-fréquences :Ce matériel est conforme aux limites établies par ICen matière d’exposition aux radiofréquences dans unenvironnement non contrôlé. Ce matériel doit être installéet utilisé à une distance d’au moins 20 cm entre l’antenneet le corps de l’utilisateur.L’émetteur ne doit pas être placé près d’une autre antenneou d’un autre émetteur, ou fonctionner avec une autreantenne ou un autre émetteur.Wireless DisclaimerThe maximum performance for wireless is derived fromIEEE Standard 802.11 specifications. Actual performancecan vary, including lower wireless network capacity,data throughput rate, range and coverage. Performancedepends on many factors, conditions and variables,including distance from the access point, volume of network traffic, building materials and construction,operating system used, mix of wireless products used,interference and other adverse conditions.Avis de non-responsabilité concernant les appar-eils sans filLes performances maximales pour les réseaux sans filsont tirées des spécifications de la norme IEEE 802.11.Les performances réelles peuvent varier, notammenten fonction de la capacité du réseau sans fil, du débitde la transmission de données, de la portée et de lacouverture. Les performances dépendent de facteurs,conditions et variables multiples, en particulier de ladistance par rapport au point d’accès, du volume du traficréseau, des matériaux utilisés dans le bâtiment et dutype de construction, du système d’exploitation et de lacombinaison de produits sans fil utilisés, des interférenceset de toute autre condition défavorable.CanadaThe following information applies if you use the productwithin Canada.Industry Canada StatementThis device complies with Industry Canada ICES-003 andRSS210 rules.Operation is subject to the following two conditions:1.This device may not cause interference and2.This device must acceptany interference, includinginterference that may cause undesired operation of the device. This device has been designed to operatewith an antenna having a maximum gain of 2dBi.Antenna having a higher gain is strictly prohibited perregulations of Industry Canada. The required antennaimpedance is 50 ohms.To reduce potential radio interference to other users,the antenna type and its gain should be so chosenthat the EIRP is not more than required for successfulcommunication.Industry Canada Radiation Exposure Statement:This equipment complies with IC radiation exposure limitsset forth for an uncontrolled environment. This equipmentshould be installed and operated with minimum distance20cm between the radiator & your body.This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter.Avis d’Industrie CanadaCet appareil est conforme aux normes NMB003 et RSS210d’Industrie Canada.L’utilisation de ce dispositif est autorisée seulement auxconditions suivantes :1.il ne doit pas produire de brouillage et2.il doit accepter tout brouillage radioélectrique reçu,même si ce brouillage est susceptible de compromettrele fonctionnement du dispositif. Le dispositif a étéconçu pour fonctionner avec une antenne ayant un gainmaximum de 2 dBi. Les règlements d’Industrie Canadainterdisent strictement l’utilisation d’antennes dont legain est supérieur à cette limite. L’impédance requisede l’antenne est de 50 ohms.Afin de réduire le risque d’interférence aux autresutilisateurs, le type d’antenne et son gain doiventêtre choisis de façon à ce que la puissance isotroperayonnée équivalente (p.i.r.e.) ne soit pas supérieureau niveau requis pour obtenir une communicationsatisfaisante.090605-10_20-10C-AI3425-01414

Navigation menu