Cisco Systems RMN302 Wireless-N Boardband Home Router User Manual

Cisco Systems Inc Wireless-N Boardband Home Router

user manual

Download: Cisco Systems RMN302 Wireless-N Boardband Home Router User Manual
Mirror Download [FCC.gov]Cisco Systems RMN302 Wireless-N Boardband Home Router User Manual
Document ID1379040
Application ID/N5FgRhOgwKbCUAwlFCYcQ==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize81.38kB (1017244 bits)
Date Submitted2010-11-19 00:00:00
Date Available2010-11-19 00:00:00
Creation Date2010-11-08 09:28:01
Producing SoftwareAcrobat Distiller 8.0.0 (Windows)
Document Lastmod2010-11-08 09:28:25
Document Titleuntitled
Document CreatorPScript5.dll Version 5.2
Document Author: sandy.lin

DRAFT - 6/25/2010
User Guide
Wireless-N Broadband
Home Router
Model: RMN302
FPO
DRAFT - 6/25/2010
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform
any servicing other than that contained in the operating instructions, unless you are qualified to do so.
Note to System Installer
For this apparatus, the cable shield/screen shall be grounded as close as practical to the point of
entry of the cable into the building.For products sold in the US and Canada, this reminder is provided
to call the system installer's attention to Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper grounding of the coaxial cable shield.
This symbol is intended to alert you that uninsulated voltage within this product may
have sufficient magnitude to cause electric shock.Therefore, it is dangerous to make any
kind of contact with any inside part of this product.
This symbol is intended to alert you of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying this product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
Notice à l’attention des installateurs de réseaux câblés
Les instructions relatives aux interventions d’entretien, fournies dans la présente notice, s’adressent exclusivement au personnel
technique qualifié. Pour réduire les risques de chocs électriques, n’effectuer aucune intervention autre que celles décrites dans le mode
d’emploi et les instructions relatives au fonctionnement, à moins que vous ne soyez qualifié pour ce faire.
Remarque à l’attention de l’installateur du système
Avec cet appareil, le blindage/Êcran du câble doit être mis à la terre aussi près que possible du point
d’entrée du câble dans le bâtiment. En ce qui concerne les produits vendus aux États-Unis et au
Canada, ce rappel est fourni pour attirer l’attention de l’installateur sur les articles 820-93 et 820-100
du Code national de l’électricité (ou Code de l'électricité canadien, Partie 1) qui fournissent des lignes
directrices concernant la mise à la terre correcte du blindage (Êcran) du câble. coaxial
Ce symbole a pour but de vous prĂŠvenir que des tensions ĂŠlectriques non isolĂŠes
existent à l’intérieur de ce produit, pouvant être d’une intensité suffisante pour causer
des chocs électriques. Il est donc dangereux d'établir un contact quelconque avec l’une
des pièces comprises à l’intérieur de ce produit.
Ce symbole a pour but de vous prévenir de la présence d’instructions importantes
relatives au fonctionnement ou à l’entretien (et aux réparations) dans la documentation
accompagnant ce produit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
DANGER ÉLECTRIQUE
NE PAS OUVRIR
ATTENTION : Pour rĂŠduire les risques de chocs ĂŠlectriques,
ne pas enlever le couvercle (ou le panneau arrière). Ne
contient aucune pièce réparable par l’utilisateur. Confier les
interventions aux techniciens d’entretien qualifiés.
AVERTISSEMENT
POUR ÉVITER LES INCENDIES OU LES CHOCS ÉLECTRIQUES,
NE PAS EXPOSER L’APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
DRAFT - 6/25/2010
Mitteilung fĂźr CATV-Techniker
Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes Fachpersonal bestimmt. Um die
Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine Wartungsarbeiten durchfĂźhren, die nicht ausdrĂźcklich in der
Bedienungsanleitung aufgeführt sind, außer Sie sind zur Durchführung solcher Arbeiten qualifiziert.
Mitteilung an den Systemtechniker
Fßr dieses Gerät muss der Kabelschutz/Schirm so nahe wie mÜglich am Eintrittspunkt des Kabels in
das Gebäude geerdet werden. Dieser Erinnerungshinweis liegt den in den USA oder Kanada
verkauften Produkten bei.Er soll den Systemtechniker auf Paragraph 820-93 und Paragraph 820-100
der US- Elektrovorschrift NEC (oder der kanadischen Elektrovorschrift Canadian Electrical Code Teil
1) aufmerksam machen, in denen die Richtlinien für die ordnungsgemäße Erdung des
Koaxialkabelschirms festgehalten sind.
Dieses Symbol weist den Benutzer auf das Vorhandensein von nicht isolierten
gefährlichen Spannungen im Gerät hin, die Stromschläge verursachen kÜnnen. Ein
Kontakt mit den internen Teilen dieses Produktes ist mit Gefahren verbunden.
Dieses Symbol weist den Benutzer darauf hin, dass die mit diesem Produkt gelieferte
Dokumentation wichtige Betriebs- und Wartungsanweisungen fßr das Gerät enthält.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ACHTUNG
STROMSCHLAGGEFAHR,
NICHT ÖFFNEN
ACHTUNG: Zur Vermeidung eines Stromschlags darf die
Abdeckung (bzw. die Geräterßckwand) nicht entfernt
werden. Das Gerät enthält keine vom Benutzer wartbaren
Teile. Wartungsarbeiten dĂźrfen nur von qualifiziertem
Fachpersonal durchgefĂźhrt werden.
AVERTISSEMENT
DAS GERÄT NICHT REGEN ODER FEUCHTIGKEIT
AUSSETZEN, UM STROMSCHLAG ODER DURCH EINEN
KURZSCHLUSS VERURSACHTEN BRAND ZU VERMEIDEN
Aviso a los instaladores de sistemas CATV
Las instrucciones de reparaciĂłn contenidas en el presente aviso son para uso exclusivo por parte de personal de mantenimiento
cualificado. Con el fin de reducir el riesgo de descarga elĂŠctrica, no realice ninguna otra operaciĂłn de reparaciĂłn distinta a las contenidas
en las instrucciones de funcionamiento, a menos que posea la cualificaciĂłn necesaria para hacerlo.
Nota para el instalador del sistema
En lo que se refiere a este aparato, el blindaje del cable debe conectarse a tierra lo mĂĄs cerca
posible al punto por el cual el cable entra en el edificio. En el caso de los productos vendidos en los
EE. UU. y CanadĂĄ, el presente aviso se suministra para llamar la atenciĂłn del instalador del sistema
sobre los ArtĂ­culos 820-93 y 820-100 del NEC (o CĂłdigo ElĂŠctrico de CanadĂĄ, Parte 1), que
proporcionan directrices para una correcta conexiĂłn a tierra del blindaje del cable coaxial.
Este sĂ­mbolo tiene como fin advertirle de que una tensiĂłn sin aislamiento en el interior
de este producto podrĂ­a ser de una magnitud suficiente como para provocar una
descarga elĂŠctrica. Por consiguiente, resulta peligroso realizar cualquier tipo de contacto
con alguno de los componentes internos de este producto.
Este sĂ­mbolo tiene como fin alertarle de la presencia de importantes instrucciones de
operaciĂłn y mantenimiento (revisiĂłn) contenidas en la literatura que acompaĂąa al
producto.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATENCIÓN
RIESGO DE DESCARGA
ELÉCTRICA NO ABRIR
ATENCIÓN: con el fin de reducir el riesgo de descarga
elĂŠctrica, no retire la tapa (ni la parte posterior). No
existen en el interior componentes que puedan ser
reparados por el usuario. Encargue su revisiĂłn a
personal de mantenimiento cualificado.
ADVERTENCIA
PA R A E V I TA R E L R I E S G O D E I N C E N D I O O D E S C A R G A
ELÉCTRICA, NO EXPONGA LA UNIDAD A LA LLUVIA O A LA
HUMEDAD.
20080814_Installer800_Intl
ii
DRAFT - 6/25/2010
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
Provide Ventilation and Select a Location
2) Keep these instructions.
• Remove all packaging material before applying power to the product.
3) Heed all warnings.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
4) Follow all instructions.
• Do not place this apparatus on an unstable surface.
5) Do not use this apparatus near water.
• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation
provides proper ventilation.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or
other objects on top of this product.
• Do not block ventilation openings.
Protect from Exposure to Moisture and Foreign Objects
WARNING: Avoid electric shock and fire hazard! Do not expose this product to
dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as vases,
should not be placed on this apparatus.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning.
Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device
(dust remover) to clean this product.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING: Avoid electric shock and fire hazard! Never push objects through the
openings in this product. Foreign objects can cause electrical shorts that can result in
electric shock or fire.
Service Warnings
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this product
only from an electrical outlet with the voltage and frequency indicated on the product label. If you
are uncertain of the type of power supply to your home or business, consult your service provider
or your local power company.
WARNING: Avoid electric shock! Do not open the cover of this product. Opening
or removing the cover may expose you to dangerous voltages. If you open the cover, your
warranty will be void. This product contains no user-serviceable parts.
The AC inlet on the unit must remain accessible and operable at all times.
Check Product Safety
Ground the Product
Upon completion of any service or repairs to this product, the service technician must perform safety
checks to determine that this product is in proper operating condition.
WARNING: Avoid electric shock and fire hazard! If this product connects to coaxial cable
wiring, be sure the cable system is grounded (earthed). Grounding provides some protection
against voltage surges and built-up static charges.
Protect the Product from Lightning
In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Verify the Power Source from the On/Off Power Light
When the on/off power light is not illuminated, the apparatus may still be connected to the power
source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged
into an AC power source.
Eliminate AC Mains Overloads
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or connecting or disconnecting
cables.
Telephone Equipment Notice
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric stock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
20090326_Modem No Battery_Safety
WARNING: Avoid electric shock and fire hazard! Do not overload AC mains, outlets,
extension cords, or integral convenience receptacles. For products that require battery power
or other power sources to operate them, refer to the operating instructions for those products.
iii
DRAFT - 6/25/2010
FCC Compliance
If you experience trouble with this telephone equipment, please contact the service provider for
information on obtaining service or repairs.
The telephone company may ask that you disconnect this equipment from the network until the problem
has been corrected or until you are sure that the equipment is not malfunctioning.
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
such interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service provider or an experienced radio/television technician for help.
Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the user’s
authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of
the FCC and is intended to supply you with information regarding the FCC approval of this device.
The phone numbers listed are for FCC-related questions only and not intended for questions
regarding the connection or operation for this device. Please contact your service provider for
any questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
1) the device may not cause harmful interference, and 2) the device must accept any interference
received, including interference that may cause undesired operation.
Cisco Wireless-N Broadband Home Router
Model: RMN302
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numĂŠrique de la class B est conforme Ă  la norme NMB-003 du Canada.
FCC Part 68
The Federal Communications Commission (FCC) of the United States restricts specific uses of modems,
and places registration responsibilities on both the manufacturer and the individual user.
1. The modem may not be connected to a party line or to a coin-operated telephone.
2. Notification to the telephone company is no longer required prior to connecting registered equipment,
but upon request from the telephone company, the user shall tell the telephone company which line
the equipment is connected to as well as the registration number and ringer equivalence number of
the registered protective circuitry. FCC information is printed on a label on the bottom of the modem.
This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA. On
the base unit of this equipment is a label that contains, among other information, a product identifier in
the format US: GEMDL01BDDR2201V1. If requested, this number must be provided to the telephone
company.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still
have those devices ring when your telephone number is called. In most, but not all areas, the sum of
the REN of all devices connected to one line should not exceed five (5.0). To be certain of the number
of devices you may connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.
If your equipment causes harm to the telephone network, the telephone company may discontinue your
service temporarily. If possible, they will notify you in advance. If advance notice is not practical, you
will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the proper functioning of your equipment. If they do, you will be notified in advance to give
you an opportunity to maintain uninterrupted telephone service.
iv
This equipment may not be used on coin service provided by the telephone company. Connection to
party lines is subject to state tariffs.
IC (Industry Canada) Notice
Notice: The Industry Canada (formerly Canadian Department of Communications) label identifies
certified equipment. This certification means that the equipment meets certain telecommunications
network protective, operational, and safety requirements. The department does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. In some cases, the company’s inside wiring associated with a
single-line individual service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user may give the
telecommunications company cause to request the user to disconnect the equipment. Users should
ensure for their own protection that the electrical ground connections of the power utility, telephone
lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as appropriate.
Radiation Exposure Statements
Note: This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 7.9 inches
(20 cm) between the radiator and your body.
US
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based on evaluation per ANI C 95.1 and FCC
OET Bulletin 65C rev 01.01. The minimum separation distance from the antenna to general bystander
is 7.9 inches (20 cm) to maintain compliance.
Canada
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1 limits. The
evaluation was based on evaluation per RSS-102 Rev 2. The minimum separation distance from the
antenna to general bystander is 7.9 inches (20 cm) to maintain compliance.
EU
This system has been evaluated for RF exposure for humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN
50385 Product Standard to Demonstrate Compliance of Radio Base Stations and Fixed Terminals
for Wireless Telecommunications Systems with basic restrictions or reference levels related to
Human Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum
separation distance from the antenna to general bystander is 20 cm (7.9 inches).
Australia
This system has been evaluated for RF exposure for humans as referenced in the Australian
Radiation Protection standard and has been evaluated to the ICNIRP (International Commission
on Non-Ionizing Radiation Protection) limits. The minimum separation distance from the antenna to
general bystander is 20 cm (7.9 inches).
20090317 FCC DSL_Dom and Intl
DRAFT - 6/25/2010
CE Compliance
Note: The full declaration of conformity for this product can be found in the Declarations of Conformity
and Regulatory Information section of the appropriate product hardware installation guide, which
is available on Cisco.com.
The following standards were applied during the assessment of the product against the requirements
of the Directive 1999/5/EC:
Declaration of Conformity with
Regard to the EU Directive
1999/5/EC
(R&TTE Directive)
• Radio: EN 300 328
• EMC: EN 301 489-1 and EN 301 489-17
• Safety: EN 60950 and EN 50385
The CE mark and class-2 identifier is affixed to the product and its packaging. This product conforms
to the following European directives:
-1999/5/EC
This declaration is only valid for configurations (combinations of software, firmware and hardware)
supported or provided by Cisco Systems for use within the EU. The use of software or firmware not
supported or provided by Cisco Systems may result in the equipment no longer being compliant
with the regulatory requirements.

[Bulgarian]
             
     1999/5/.
   

National Restrictions
This product is for indoor use only.
esky
[Czech]:
Toto zaĂ­zenĂ­ je v souladu se zĂĄkladnĂ­mi poĹžadavky a ostatnĂ­mi odpovĂ­dajĂ­cĂ­mi
ustanovenĂ­mi Smrnice 1999/5/EC.
France
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med de vĂŚsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used outdoors in the
band 2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band.
Check http://www.arcep.fr/ for more details.
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren
entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele
sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
EspaĂąol
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones
de la Directiva 1999/5/CE.
!""#$%&*
[Greek]:
+467; < =>=%; 6#; `Y#{JL; 1999/5/EC.
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Italiano
[Italian]:
Questo apparato ĂŠ conforme ai requisiti essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/CE.
Latviski
[Latvian]:
Š~ iekrta atbilst Direkt~vas 1999/5/EK b€tiskajm pras~bm un citiem ar to
saist~tajiem noteikumiem.
2,4 GHz frekven?u joslas izmantoĹĄanai ?rpus telp?m nepiecieĹĄama at?auja no Elektronisko sakaru
direkcijas. Vair?k inform?cijas: http://www.esd.lv.
Lietuvi
[Lithuanian]:
Šis ‚renginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios
direktyvos nuostatas.
Note: The regulatory limits for maximum output power are specified in EIRP. The EIRP level of a
device can be calculated by adding the gain of the antenna used (specified in dBi) to the output
power available at the connector (specified in dBm).
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde
bepalingen van de Richtlijn 1999/5/EC.
Malti
[Maltese]:
Dan l-apparat huwa konformi mal-„ti iet essenzjali u l-provedimenti l-o„ra rilevanti
tad-Direttiva 1999/5/EC.
Magyar
[Hungarian]:
Ez a készülék teljesíti az alapvet‡ követelményeket és más 1999/5/EK irányelvben
meghatĂĄrozott vonatkozĂł rendelkezĂŠseket.
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Urzˆdzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami
okre‰lonymi Dyrektywˆ UE: 1999/5/EC.
PortuguĂŞs
[Portuguese]:
Este equipamento estĂĄ em conformidade com os requisitos essenciais e outras
provisĂľes relevantes da Directiva 1999/5/EC.
RomânŠ
[Romanian]
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi
relevante ale Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji
Direktive 1999/5/EC.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so zåkladnými poŞiadavkami a inými prísluťnými
nariadeniami direktĂ­v: 1999/5/EC.
Suomi
[Finnish]:
Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä
asetettujen muiden laitetta koskevien määräysten mukainen.
Svenska
[Swedish]:
Denna utrustning är i Üverensstämmelse med de väsentliga kraven och andra
relevanta bestämmelser i Direktiv 1999/5/EC.
Pour la bande 2,4 GHz, la puissance est limitĂŠe Ă  10 mW en p.i.r.e. pour les ĂŠquipements utilisĂŠs en
extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations dans
d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour de plus amples détails.
Italy
This product meets the National Radio Interface and the requirements specified in the National
Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the
boundaries of the owner’s property, its use requires a “general authorization.” Please check http://
www.comunicazioni.it/it/ for more details.
Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale
di ripartizione delle frequenze in Italia. Se non viene installato all ‘interno del proprio fondo, l’utilizzo di
prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.comunicazioni.
it/it/ per maggiori dettagli.
Latvia
The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications
Office. Please check http://www.esd.lv for more details.
Antennas
Use only the antenna supplied with the product.
20090312 CE_Gateway
DRAFT - 6/25/2010
Disclaimer
U.S. Patents
Cisco Systems, Inc. assumes no responsibility for errors or
omissions that may appear in this guide. We reserve the right to
change this guide at any time without notice.
A patent notice is affixed to this product. In addition, the product
may also be covered by one or more of the following patents:
Documentation Copyright Notice
Information in this document is subject to change without notice.
No part of this document may be reproduced in any form without
the express written permission of Cisco Systems, Inc.
Software and Firmware Use
The software described in this document is protected by copyright
law and furnished to you under a license agreement. You may only
use or copy this software in accordance with the terms of your
license agreement.
The firmware in this equipment is protected by copyright law. You
may only use the firmware in the equipment in which it is provided.
Any reproduction or distribution of this firmware, or any portion of
it, without our express written consent is prohibited.
vi
4,498,169, 4,692,919, 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456;
4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207; 5,045,816; 5,053,883;
5,054,071; 5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925;
5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364; 5,255,086; 5,257,403; 5,267,071; 5,270,809;
5,271,041; 5,272,752; 5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709;
5,341,425; 5,347,388; 5,347,389; 5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145;
5,381,481; 5,390,337; 5,400,401; 5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404;
5,430,568; 5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492;
5,477,199; 5,477,262; 5,477,282 5,477,370; 5,481,389; 5,481,542; 5,485,221; 5,493,339; 5,497,187;
5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562;
5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388; 5,657,414; 5,675,575; 5,684,876; 5,715,515;
5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829;
5,826,167; 5,850,305; 5,854,703; 5,870,474; 5,892,607; 5,920,626; 5,923,755; 5,930,024; 5,930,515;
5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163;
6,028,941; 6,029,046; 6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039; 6,157,719; 6,188,729;
6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226;
6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714; 6,424,717;
6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519; 6,516,002; 6,516,412;
6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984;
6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598; 6,721,352; 6,721,956; 6,725,459; 6,738,982;
6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028;
6,822,972; 6,823,385; 6,832,386; 6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622;
6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121;
6,978,310; 6,986,156; 6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572;
D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535; D513407;
D516518; RE36368; RE36988
20070417 Patents
DRAFT - 6/25/2010
Table of Contents
Product Overview ............................................................................................................3
Front Panel............................................................................................................................................................................................3
Top Panel ...............................................................................................................................................................................................4
Back Panel.............................................................................................................................................................................................5
Connecting to the Network...................................................................................................................................5
Placement Positions.....................................................................................................................................................................6
Wireless Security Checklist ...........................................................................................7
General Network Security Guidelines ..........................................................................................................................8
Additional Security Tips ............................................................................................................................................................8
Advanced Configuration .................................................................................................8
How to Access the Web-Based Utility ..........................................................................................................................8
Setup > ADSL .....................................................................................................................................................................................9
Setup > ADSL (WAN Connection for PVC) ............................................................................................................13
Setup > Ethernet ...........................................................................................................................................................................16
Setup > Local Network ............................................................................................................................................................18
Setup > DDNS.................................................................................................................................................................................20
Setup > Advanced Routing .................................................................................................................................................21
Setup > PVC/VLAN Mapping ............................................................................................................................................22
Wireless > Basic Settings .....................................................................................................................................................23
Wireless > Security ....................................................................................................................................................................23
Wireless > MAC Filter ...............................................................................................................................................................25
Wireless > Wi-Fi Protected Setup.................................................................................................................................25
Wireless > Advanced Settings .........................................................................................................................................27
Voice .......................................................................................................................................................................................................28
Voice > Info ........................................................................................................................................................................................28
Voice > System ..............................................................................................................................................................................30
Voice > User1/2 ............................................................................................................................................................................30
Storage > Disk Detail .................................................................................................................................................................31
Storage > Disk Management .............................................................................................................................................32
Security > Firewall .......................................................................................................................................................................32
Access Restrictions > Internet Access Policy .....................................................................................................33
Applications & Gaming > Single Port Forwarding ...........................................................................................34
Applications & Gaming > Port Range Forwarding ...........................................................................................35
Applications & Gaming > DMZ .........................................................................................................................................35
Applications & Gaming > Port Range Triggering .............................................................................................36
Applications & Gaming > QoS ..........................................................................................................................................36
Applications & Gaming > Service ..................................................................................................................................39
Administration > Management .........................................................................................................................................40
Administration > Log .................................................................................................................................................................41
Administration > Diagnostic................................................................................................................................................42
Administration > Backup ........................................................................................................................................................42
Administration > Factory Defaults .................................................................................................................................42
Administration > Upgrade ....................................................................................................................................................43
Administration > Reboot ........................................................................................................................................................43
Administration > Logout .........................................................................................................................................................43
Status > Internet ............................................................................................................................................................................44
Status > Local Network............................................................................................................................................................44
Status > Wireless .........................................................................................................................................................................45
Status > DSL Connection......................................................................................................................................................45
Status > Bridges............................................................................................................................................................................46
Troubleshooting ............................................................................................................ 47
Specifications ................................................................................................................ 48
Software License Agreement...................................................................................... 49
Software in Cisco Products ................................................................................................................................................49
Software Licenses.......................................................................................................................................................................49
DRAFT - 6/25/2010
DRAFT - 6/25/2010
Product Overview
Thank you for choosing the CiscoÂŽ Wireless-N Broadband Home Router. The Router
lets you access the Internet via a wireless connection or through one of its four (or five)
switched ports.
You can also use the Router to share resources such as computers and storage. Various
security features help to protect your data and your privacy while you are online. Security
features include WPA2 security, a Stateful Packet Inspection (SPI) firewall, and NAT
technology. Configuring the Router is easy using the provided browser-based utility.
Front Panel
FPO
Power
(Green/Red) The Power LED lights up when the Router is powered on. It
flashes during the self-test. The LED becomes red during a malfunction.
Internet
(Green/Red)The Internet LED lights up when the Router is connected to the
Internet. It flashes to indicate network activity over the Internet port. The LED
becomes red when the Internet connection fails.
WAN
(Green) The WAN LED corresponds with the WAN port and serves two
purposes. If the LED is continuously lit, the Router is successfully connected
to a device through that port. It flashes to indicate network activity over that
port.
WAN MOCA (Green) Text TBD
LAN MOCA (Green)Text TBD
LAN 1-4
(Green) These numbered LEDs, corresponding with the numbered Ethernet
ports on the Router’s back panel, serve two purposes. If the LED is
continuously lit, the Router is connected to a device through that port. It
flashes to indicate network activity over that port.
WLAN
(Green) The WLAN LED lights up when the wireless feature is enabled.
It flashes when the Router is sending or receiving data over the wireless
network.
USB 1
and 2
(Green) The USB LED lights up when the Router is connected to a device
through the USB port. It flashes to indicate USB activity.
WPS
(Green/Red) The WPS LED lights up when wireless security is enabled. It
flashes during the Wi-Fi Protected Setup process. The LED becomes red
when wireless security is disabled.
DRAFT - 6/25/2010
Top Panel
Wi-Fi Protected
Setup
If you have a client device, such as a wireless adapter, that supports
Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to
automatically configure wireless security for your wireless network(s).
Note: Wi-Fi Protected Setup can only be used for the default wireless
network. (The Router supports up to four wireless networks. The other
three can be configured using the Router’s web-based utility.)
FPO
Follow the appropriate instructions:
Method #1
Use this method if your client device has a Wi-Fi Protected Setup button.
1. Click or press the Wi-Fi Protected Setup button on the client device. (If Wi-Fi Protected
Setup is an on-screen option, then select it.)
2. Click the Wi-Fi Protected Setup button on the top panel of the Router.
3. After the client device has been configured, refer back to your client device or its
documentation for further instructions.
Method #2
Use this method if your client device has a Wi-Fi Protected Setup PIN number.
1.
2.
3.
4.
Access the Router’s web-based utility.
Click the Wireless tab.
Click the Wi-Fi Protected Setup tab
Enter the client PIN number in the PIN field on this screen (the Router’s Wi-Fi Protected
Setup screen).
5. Click Register.
Method #3
Use this method if your client device asks for the Router’s PIN number.
1. Enter the PIN number listed on the label on the bottom of the Router.
2. After the client device has been configured, refer back to your client device or its
documentation for further instructions.
Note: Wi-Fi Protected Setup configures one client device at a time. Repeat the instructions
for each client device that supports Wi-Fi Protected Setup.
DRAFT - 6/25/2010
Back Panel
Reset
FPO
There are two ways to reset the Router’s settings to factory defaults.
Either press and hold the Reset button for approximately ten seconds, or
restore the defaults from the Administration > Factory Defaults screen of
the Router’s web-based utility.
Note: The reset does not restore the voice settings to the factory defaults.
WPS
Text TBD
USB
The USB port connects to a USB storage device, such as a USB hard drive
or flash disk.
Ethernet
LAN 1-4
These Ethernet ports (1, 2, 3, 4) connect the Router to wired computers
and other Ethernet network devices.
F Connector Text TBD
Ethernet
The WAN/LAN5 port can act as a Wide Area Network (WAN) or Local Area
WAN/LAN5 Network (LAN) port. As a WAN port, it connects to a broadband modem.
As a LAN port, it connects to a wired computer or other Ethernet network
device.
Connecting to the Network
1.
Use a coaxial cable to connect the F-Conn port on the RMN302 to the
wall connector or to the coaxial network used to distribute IP data.
2.
Use an Ethernet cable to connect the LAN port on the RMN302 to your
home network or to a PC.
3.
Attach the power adapter to the POWER port on the back of the
RMN302, and plug it into a wall outlet.
4.
Turn on the power switch.
FPO
To Wall
Outlet
Guide
Record
ANNE L
CH
TV
VOLUME
PC or
Home Network
CISCO 8455DVB
T14758
Coaxial Network
Set-Top Box
DRAFT - 6/25/2010
Placement Positions
There are two ways to physically install the Router. The first way is to place the Router
horizontally on a surface. The second way is to mount the Router on a wall.
Horizontal Placement
The Router has four rubber feet on its bottom panel. Place the Router on a level surface
near an electrical outlet.
Wall-Mounting Placement
The Router has four wall-mount slots on its bottom panel. The distance between two
adjacent slots is 54 mm (2.13 inches).
Two screws are needed to mount the Router.
Suggested Mounting Hardware
2.5 to 3.0 mm
4 to 5 mm
1 to 1.5 mm
Note: Mounting hardware illustrations are not true to scale.
Note: Cisco is not responsible for damages incurred by insecure wall-mounting hardware.
Follow these instructions:
1. Determine where you want to mount the Router. Make sure that the wall you use is smooth,
flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.
2. Drill two holes into the wall. Make sure the holes are 54 mm (2.13 inches) apart.
3. Insert a screw into each hole and leave 2 mm (0.8 inches) below the head exposed.
4. Maneuver the Router so two of the wall-mount slots line up with the two screws.
5. Place the wall-mount slots over the screws and slide the Router down until the screws fit
snugly into the wall-mount slots.
Note: To safely wall-mount the Router, the side panel with the antenna must face upward.
54 mm
Print this page at 100% size. Cut along the dotted
line, and place on the wall to drill precise spacing.
Wall Mounting Template
DRAFT - 6/25/2010
Wireless Security Checklist
Wireless networks are convenient and easy to install, so homes with high-speed Internet
access are adopting them at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more vulnerable to intruders than a
traditional wired network. Like signals from your cellular or cordless phones, signals from
your wireless network can also be intercepted. Since you cannot physically prevent
someone from connecting to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless network name or SSID
Wireless devices have a default wireless network name or Service Set Identifier (SSID) set
by the factory. This is the name of your wireless network, and can be up to 32 characters
in length. Cisco wireless products use cisco as the default wireless network name. You
should change the wireless network name to something unique to distinguish your
wireless network from other wireless networks that may exist around you, but do not use
personal information (such as your Social Security number) because this information may
be available for anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points, routers, and gateways, you will be asked for a
password when you want to change their settings. These devices have a default password
set by the factory. The Cisco default password is admin. Hackers know these defaults and
may try to use them to access your wireless device and change your network settings. To
thwart any unauthorized changes, customize the device’s password so it will be hard to
guess.
3. Enable MAC address filtering
Cisco routers and gateways give you the ability to enable Media Access Control (MAC)
address filtering. The MAC address is a unique series of numbers and letters assigned to
every networking device. With MAC address filtering enabled, wireless network access is
provided solely for wireless devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home so that only those computers can
access your wireless network.
4. Enable encryption
Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access
(WPA/WPA2) and Wired Equivalency Privacy (WEP) offer different levels of security for
wireless communication.
A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP,
because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes
over the airwaves, you should enable the highest level of encryption supported by your
network equipment.
WEP is an older encryption standard and may be the only option available on some older
devices that do not support WPA.
DRAFT - 6/25/2010
General Network Security Guidelines
Wireless network security is useless if the underlying network is not secure.
• Password protect all computers on the network and individually password protect
sensitive files.
• Change passwords on a regular basis.
• Install anti-virus software and personal firewall software.
• Disable file sharing (peer-to-peer). Some applications may open file sharing without
your consent and/or knowledge.
Additional Security Tips
• Keep wireless routers, access points, or gateways away from exterior walls and
windows.
• Turn wireless routers, access points, or gateways off when they are not being used (at
night, during vacations).
• Use strong passphrases that are at least eight characters in length. Combine letters
and numbers to avoid using standard words that can be found in the dictionary.
Web: For more information on wireless security, visit www.linksysbycisco.com/security
Advanced Configuration
To configure the Router, use its web-based utility. This chapter describes each web page
of the utility and each page’s key functions. You can access the utility via a web browser on
a computer connected to the Router.
Note: If your service provider supplied you with the Router, then it may be pre-configured
for you, and you will not need to make any changes. Contact your service provider for more
information.
The web-based utility has these main tabs: Setup, Wireless, Storage, Security, Parental
Control, Applications & Gaming, Administration, Status, and Advanced. Additional tabs will
be available after you click one of the main tabs.
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on your computer, and enter the
Router’s default IP address, 192.168.1.1, in the Address field. Then, press Enter.
A login screen appears. The first time you open the web-based utility, use the default user
name and password, admin and password. (You can set a new user name and password
from the Administration tab’s Management screen.) Click OK to continue.
Note: If the Router was supplied by your service provider, then it may restrict access to the
web-based utility. Contact your service provider for the login information.
Login Screen
DRAFT - 6/25/2010
Setup > Interface
WAN Interface Setup
WAN Connection Settings
Network Type: Choose your WAN interface type from the dropdown list. Options include
Auto-Detection, MoCA, and Ethernet.
• Auto Detection: The router detects physical interface automatically and determine
the connection type. The detect result is displayed in “Current Network” field;
• MoCA: You can manually configure MoCA connection as physical interface.
• Ethernet: You can manually configure the layer 2 network as Ethernet WAN connection
Setup > Interface
Current Network: Indicates whether the current WAN connection is MoCA or Ethernet
WAN, and whether the connection is manually configured or auto-detected.
Ethernet WAN settings
Set Connection Shaping: Choose whether you want the router to smooth the ethernet
bandwidth. Options include No Shaping, Auto(link speed) and Manual.
MoCA WAN settings
Channel: Allow the router to detect an available frequency for your MoCA WAN, or choose
a channel frequency.
Node Type: Allow the router to detect your node type, or choose the correct option.
Auto-Detect privacy: Choose this option if you want to enable privacy auto detection.
MoCA Privacy: Choose this option if you want to enable privacy on your MoCA WAN
connection.
Password: If you chose to enable privacy on your MoCA WAN, enter your password here.
Power Limit: Allow the router to set the limit for the transmission power on your MoCA
WAN, or choose a percentage of power to use as a limit.
MoCA LAN Setup
MoCA LAN Settings
Channel: Allow the router to detect an available frequency for your MoCA LAN, or choose
a channel frequency.
MoCA Privacy: Choose this option if you want to enable privacy on your MoCA LAN
connection.
Password: If you chose to enable privacy on your MoCA LAN, enter your password here.
Power Limit: Allow the router to set the limit for the transmission power on your MoCA
WAN, or choose a percentage of power to use as a limit.
DRAFT - 6/25/2010
Setup > Internet
WAN Connection Settings
Network Type: Choose your network type. Connection Type
Auto Detection Settings
Auto Detect Connection: Allows you to enable or disable internet connection type auto
detection.
Protocol Detection: Select this checkbox if you want the router to detect the internet connection
continuously, as defined by the Auto Detection Interval.
Auto Detection Interval: Specify how often the router should detect the internet connection (if
you chose Protocol Detection).
Ethernet WAN Setup
Setup > Internet
Connection Type: Choose whether your WAN uses IPoE (including DHCP and static IP) or
PPPoE.
IPoE Settings
IPoE Connection: Need text.
Gateway Probing: Choose whether you want to probe the gateway if the gateway is alive. Select
ARP to resolve MAC address by default.
Probing Using Unicast: Choose whether you want to ping the gateway with an ICMP request.
Probing Only on Idle: Choose whether you want to restrict probing if traffic is going through
router.
Probing Interval: Specify your probing interval, in seconds.
Probing Reset Trigger: Specify how long the probe should run before resetting the connection
10
DRAFT - 6/25/2010
PPPoE Settings for PPPoE (RFC2516)
Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System)
server IP address(es) provided by your service provider. At least one is required.
Username and Password Enter the Username and Password provided by your service
provider.
Setup > ADSL (WAN Connection for PVC) >
PPPoE (RFC2516)
Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection
after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection
has been terminated due to inactivity, Connect on Demand enables the Router to automatically
re-establish your connection as soon as you attempt to access the Internet again. To use this
option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes
you want to have elapsed before your Internet connection terminates. The default Max Idle Time
is 5 minutes.
Keep Alive If you select this option, the Router will periodically check your Internet connection.
If you are disconnected, then the Router will automatically re-establish your connection. To use
this option, select Keep Alive.
11
DRAFT - 6/25/2010
Setup > Local Network
Configure the Router’s Local Area Network (LAN) settings on this screen.
There are two views available, Basic and Advanced. The default view is Basic. To display the
Advanced View, click Advanced View. To return to the Basic View, click Basic View.
Local Network
The Local Network section changes the settings on the network connected to the Router’s
Ethernet ports. Wireless setup is performed through the Wireless tab.
Router IP
The values for the Router’s local IP Address and Subnet Mask are displayed. In most cases,
keeping the default values will work.
IP Address The default value is 192.168.1.1.
Subnet Mask The default value is 255.255.255.0.
Network Address Server Settings (DHCP)
The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP)
server function. The Router can be used as a DHCP server for your network. A DHCP server
automatically assigns an IP address to each computer on your network. If you choose to enable
the Router’s DHCP server option, make sure there is no other DHCP server on your network.
Setup > Local Network (Advanced View)
DHCP Server A Dynamic Host Configuration Protocol (DHCP) server automatically assigns
an IP address to each computer on your network for you. Unless you already have one, Cisco
recommends that you keep the default, Enabled.
DHCP Options To configure DHCP options (available if DHCP is enabled), click this option. A
new window appears.
DHCP Option
• DHCP Option Select the appropriate setting.
• DHCP Option Value Enter the appropriate IP address, which is stored as a binary string
on the Router. (No check is performed on these values.)
Click Save Settings to apply your changes, or click Go Back to cancel your changes and
return to the Local Network screen.
Conditional Serving To configure the Conditional Serving Pool settings (available if DHCP is
enabled), click this option. A new window appears.
Setup > Local Network > DHCP Option
12
DRAFT - 6/25/2010
Conditional Serving
Conditional Serving Pool
Enable DHCP Conditional Serving To enable this option, select the check box.
Otherwise, leave the check box blank.
For each entry, the table lists the following: MAC Address, Vendor Class ID, User Class ID,
Client ID, Host Name, Domain Name, IP Address, Precedence, and Action. To delete an
entry, click Delete. To configure the DHCP options for an entry, click DHCP Option.
Conditional Serving Entry
Precedence Enter the Precedence value. A lower value indicates higher priority.
MAC Address Enter the MAC Address, if applicable as a filter condition.
Setup > Local Network > Conditional Serving
Vendor Class ID Enter the Vendor Class ID, if applicable as a filter condition.
User Class ID Enter the User Class ID, if applicable as a filter condition.
Client ID Enter the Client ID, if applicable as a filter condition. This field accepts ASCII or
hexadecimal strings. To enter a hexadecimal string, add Ox before the string.
Host Name Enter the Host Name, if applicable as a filter condition.
Domain Name If there is a match, the DHCP server will assign this Domain Name to the
host.
IP Address If there is a match, the DHCP server will assign this IP Address to the host.
Click Add Entry to add a new entry to the table. Click Save Settings to apply your changes.
Click Back to LAN Setup to return to the Local Network screen.
Starting IP Address Enter a value for the DHCP server to start with when issuing IP addresses.
Because the Router’s default IP address is 192.168.1.1, the Starting IP Address must be
192.168.1.2 or greater, but smaller than 192.168.1.253. The default is 192.168.1.64.
Ending IP Address Specify the final IP address of the range available for assignment. The
default is 192.168.1.253.
Client Lease Time The Client Lease Time is the amount of time a network device will be allowed
connection to the Router with its current dynamic IP address. Enter the number of minutes
that the device will be “leased” this dynamic IP address. After the time is up, the device will be
automatically assigned a new dynamic IP address. The default is 1440 minutes.
DNS Proxy (Advanced View) The Domain Name System (DNS) is how the Internet translates
domain or website names into Internet addresses or URLs. To use DNS Proxy, keep the default,
Enable. Otherwise, select Disable.
Static DNS 1-3 (Advanced View) These entries are valid only when the DNS Proxy option is
disabled. At least one DNS server IP address is provided by your service provider. You can
enter up to three DNS server IP addresses here. The Router will use these for quicker access to
functioning DNS servers.
WINS (Advanced View) The Windows Internet Naming Service (WINS) converts NetBIOS
names to IP addresses. If you use a WINS server, enter that server’s IP address here. Otherwise,
leave this field blank.
Domain Name (Advanced View) Enter the Domain Name of your local network.
Reserved IP List (Advanced View) Enter the IP addresses you want to reserve, so they will not
be leased to DHCP clients.
13
DRAFT - 6/25/2010
Advanced DHCP Settings (Advanced View)
DHCP Address This option defines the DHCP address allocation method. To assign local IP
addresses from the DHCP pool you have defined, keep the default, Use DHCP Pool.
To have the local network devices share the WAN subnet address, select Use WAN
Subnet. In this pass-through mode, the local computers get WAN-side IP addresses. They
bypass NAT and are visible on the service provider’s network. However, these computers
can still communicate with other computers that are allocated private IP addresses.
To have a local network device share the WAN IP address, select Share WAN IP. In this
mode, which is also known as super-DMZ mode, a single computer bypasses NAT. You
can specify the computer’s MAC address in the MAC Address field.
WAN IP Interface If you selected Use WAN Subnet or Share WAN IP, select the appropriate
WAN IP connection to use.
MAC Address If you selected Share WAN IP, enter the MAC address of the local network device.
Lease Time Enter the number of seconds you want the local network device to lease the WAN
IP address.
Time Settings (Advanced View)
Time Zone Select the time zone in which your network functions.
Automatically adjust clock for daylight saving changes Select this option if you want the Router
to automatically adjust for daylight saving time.
NTP Server 1/2 Enter the URL (web address) of the Network Time Protocol (NTP) server you
want to use. The default NTP servers are time.nist.gov and clock.isc.org.
Update Time Click this option to immediately synchronize the Router with the NTP server.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Setup > DDNS
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign
a fixed host and domain name to a dynamic Internet IP address. It is useful when you are
hosting your own website, FTP server, or other server behind the Router.
Before you can use this feature, you need to sign up for DDNS service with a DDNS service
provider, www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the
default, Disabled.
DDNS
Setup > DDNS
DDNS Service
Disabled/DynDNS.org/TZO.com If your DDNS service is provided by DynDNS.org, then
select DynDNS.org from the drop-down menu. If your DDNS service is provided by TZO, then
select TZO.com. The features available on the DDNS screen will vary, depending on which
DDNS service provider you use.
WAN IP The WAN IP address of the Router is displayed.
User/Email Enter the user name or e-mail address for your account.
Password/Key Enter the password or key for your account.
Host Name Enter the DDNS URL assigned by the service.
Status The status of the DDNS service connection is displayed.
14
DRAFT - 6/25/2010
Connect To manually trigger an update, click this button.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Setup > Advanced Routing
This screen is used to set up the Router’s advanced routing functions. Static Routing sets
up a fixed route to another network destination.
Advanced Routing
Routing Table
For each route, the Destination LAN IP address, Subnet Mask, Router, and Metric are
displayed. In the Action column, click Delete to delete a static route.
Default Interface The default Layer 3 connection is displayed.
Default Router The default next-hop gateway of the default interface is displayed.
Setup > Advanced Routing
Default Connection This advanced setting usually indicates the default connection since the
Router supports multiple WAN connections. If the Router has multiple connections, specify
which one is the default.
Static Routing
A static route is a pre-determined pathway that network information must travel to reach a
specific host or network. Enter the information described below to set up a new static route.
Note: When you add a static route, certain rules apply. For example, the Router must
belong to the subnet of any of the router’s interfaces.
Destination IP Address The Destination IP Address is the IP address of the remote network or
host to which you want to assign a static route.
Subnet Mask The Subnet Mask determines which portion of a Destination IP Address is the
network portion, and which portion is the host portion.
Router This is the IP address of the gateway device that allows for contact between the Router
and the remote network or host.
Metric This is the number of hops to each node until the destination is reached (16 hops
maximum). Enter the appropriate Metric. The default is 1.
To save the static route you have configured, click Add Entry. Click Save Settings to
apply your changes, or click Cancel Changes to cancel your changes.
15
DRAFT - 6/25/2010
Setup > PVC/VLAN Mapping
This advanced screen is used to map the PVCs to the Virtual Local Area Networks (VLANs).
When you create a mapping, a layer 2 bridge is formed between the Router’s LAN port
(including WLAN SSID) and WAN port (PVC or Ethernet WAN).
You should configure this screen according to your service provider’s instructions. For
example, when Ethernet port 1 is connected to a set-top box, a PVC mapping is created for
Ethernet port 1 and PVC 1 with VLAN 1002. Traffic is marked with the configured VLAN ID
when it travels to the service provider’s network.
PVC VLAN Mapping
Select PVC Connection Select the PVC you want to map.
VLAN Bridge Table
Setup > PVC/VLAN Mapping
For each entry, the table lists the following: LAN Ports, VLAN ID, 802.1p, MAC Address,
Ethernet Frame, Enable status, and Action. To delete an existing PVC/VLAN mapping, click
Delete.
VLAN Bridge Entry
Enabled Select Enabled to enable the mapping rule.
VLAN ID Enter the VLAN you want to map. The default is 2.
MAC Address Enter the packet’s source MAC address, if applicable as a filter condition.
802.1p Enter the priority level for each port. These are the mappings to 802.1p:
• 6 High (highest, EF)
• 5 Medium (CS)
• 4 Normal (CS)
• 0 Low (best effort)
• -1 No Change (no change to the original 802.1p value)
Cisco recommends the following:
• For voice and video traffic, enter 6.
• For gaming or mission-critical traffic, enter 5.
• For normal traffic, enter 4.
• For low-priority traffic, enter 0.
LAN Ports Every LAN interface is listed, including the Ethernet ports and Wireless Local Area
Network (WLAN) ports. (The WLAN ports are listed with their wireless network names, also
known as SSIDs.) Select the appropriate LAN interface. For multiple selection, press the Ctrl or
Shift key. To deselect, use Ctrl + click (click the selection).
Ethernet Frame The Ethernet frame types are listed. Select the packet’s Ethernet frame type,
if applicable as a filter condition. For multiple selection, press the Ctrl or Shift key. To deselect,
use Ctrl + click (click the selection).
Click Add VLAN Bridge to create a new PVC/VLAN mapping, or click Cancel Changes to
cancel your changes.
16
DRAFT - 6/25/2010
Wireless > Basic Settings
The basic settings for wireless networking are set on this screen.
There are two ways to configure the Router’s wireless settings, manual and Wi-Fi Protected
Setup. For manual configuration, use this screen to change the settings.
Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you
have devices that support Wi-Fi Protected Setup, then click the Wi-Fi Protected Setup
tab, and follow the on-screen instructions (refer to the “Wireless > Wi-Fi Protected Setup”
section for more information).
Wireless > Basic Settings
Note: Wi-Fi Protected Setup can only be used for the default wireless network. (The
Router supports up to four wireless networks. The other three can be configured using
the Router’s web-based utility.)
Wireless Network
Wireless Channel Select the channel you want to use. All devices in your wireless network
must use the same channel in order to communicate.
Wireless Network State Select the wireless standards running on your network. If you have
Wireless-G and Wireless-B devices in your network, keep the default, Mixed. If you have only
Wireless-G devices, select G-Only. If you have only Wireless-B devices, select B-Only. If you do
not have any wireless devices, select Disabled.
The Router supports up to four wireless networks. By default, only the first wireless network
is enabled. On the Wireless Security and MAC Filter screens, you can configure different
security settings and MAC filtering rules for each wireless network.
Configure the following settings for each wireless network (SSID1-4):
Wireless Network Name (SSID) The network name is case-sensitive and must not exceed
32 characters (use any of the characters on the keyboard). Cisco recommends that you change
the default name of the first network, linksys1, to a unique name of your choice.
Wireless Network State If you want to use the wireless network, select Enabled. Otherwise,
select Disabled.
Wireless SSID Broadcast When wireless devices survey the local area for wireless networks
to associate with, they will detect the wireless network name or SSID broadcast by the Router. If
you want to broadcast the Router’s SSID, keep the default, Enabled. Otherwise, select Disabled.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Wireless > Security
The Security screen configures the security of your wireless network(s). The Router supports
the following wireless security mode options: WPA2-Personal, WPA-Personal, WEP, WPAEnterprise, and WPA2-Enterprise. (WPA stands for Wi-Fi Protected Access, which is a
security standard stronger than WEP encryption, and WEP stands for Wired Equivalent
Privacy.) For detailed instructions on configuring wireless security for the Router, refer to
“Wireless Security Checklist” on page 7.
Note: If you used Wi-Fi Protected Setup to configure your wireless network(s), then
wireless security has already been set up. Do not make changes to the Wireless Security
screen.
17
DRAFT - 6/25/2010
Wireless Security
Wireless Network Select the wireless network you want to configure.
Security Mode Select the security method for your wireless network. Proceed to the
appropriate instructions. If you do not want to use wireless security, keep the default, Off.
Note: If you are using wireless security, remember that each device in your wireless
network MUST use the same security method and settings, or else the wireless devices
cannot communicate.
WPA2-Personal
Security Mode > WPA2-Personal
Mixed Mode Select Enabled to support both WPA and WPA2 clients. Otherwise, keep the
default, Disabled.
Encryption Select the appropriate method, AES or TKIP or AES.
Passphrase Enter a Passphrase (also called a WPA shared key) of 8-63 characters.
Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change
the encryption keys. The default is 3600 seconds.
WPA-Personal
Encryption TKIP is automatically selected.
Security Mode > WPA-Personal
Passphrase Enter a Passphrase (also called a WPA shared key) of 8-63 characters.
Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change
the encryption keys. The default is 3600 seconds.
WEP
Encryption Select a level of WEP encryption, 40/64-bit (10 hex digits) or 104/128-bit (26
hex digits).
Passphrase Enter a Passphrase to automatically generate WEP keys. Then click Generate.
Note: The WEP Passphrase is compatible with Cisco wireless products only. If you are
using non-Cisco products, manually enter the appropriate WEP key on those devices.
Key 1-4 If you did not enter a Passphrase, enter the WEP key(s) manually.
Security Mode > WEP
TX Key Select which TX (Transmit) Key to use. The default is 1.
WPA Enterprise
This option features WPA used in coordination with a RADIUS server. (RADIUS stands for
Remote Authentication Dial-In User Service. This option should only be used when a RADIUS
server is connected to the Router.)
Encryption TKIP is automatically selected.
RADIUS Server Enter the IP address of the RADIUS server.
RADIUS Port Enter the port number of the RADIUS server. The default value is 1812.
Shared Key Enter the key shared between the Router and the server.
Security Mode > WPA Enterprise
18
Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change
the encryption keys. The default is 3600 seconds.
DRAFT - 6/25/2010
WPA2 Enterprise
This option features WPA2 used in coordination with a RADIUS server. (It should only be used
when a RADIUS server is connected to the Router.)
Mixed Mode Select Enabled to support both WPA and WPA2 clients. Otherwise, keep the
default, Disabled.
Encryption Select the appropriate method, AES or TKIP or AES.
RADIUS Server Enter the IP address of the RADIUS server.
RADIUS Port Enter the port number of the RADIUS server. The default value is 1812.
Shared Key Enter the key shared between the Router and the server.
Security Mode > WPA2 Enterprise
Key Renewal Enter a Key Renewal period, which instructs the Router how often it should change
the encryption keys. The default is 3600 seconds.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Wireless > MAC Filter
Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting
within your network’s radius.
Wireless MAC Filter
Select Wireless Network (SSID) Select the wireless network you want to configure.
Enabled/Disabled To use the wireless MAC filter, select Enabled. Otherwise, keep the default,
Disabled.
MAC Address Filter
Filter As White List/Filter As Black List To allow access by network devices with the MAC
addresses on this list, select Filter As White List. To block access by network devices with the MAC
addresses on this list, keep the default, Filter As Black List.
Wireless > MAC Filter
MAC 01-20 Enter the MAC addresses of the devices whose wireless access you want to block
or allow.
For each wireless device, its MAC address and connection status are listed. To copy a
MAC address to one of the MAC 01-20 fields, click Copy.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Wireless > Wi-Fi Protected Setup
There are two ways to configure the Router’s wireless settings, manual and Wi-Fi Protected
Setup. For manual configuration, click the Basic Settings tab (refer to the “Wireless > Basic
Settings” section for more information).
Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you
have devices that support Wi-Fi Protected Setup, then use the following instructions.
Note: Wi-Fi Protected Setup can only be used for the default wireless network. (The
Router supports up to four wireless networks. The other three can be configured using
the Wireless > Basic Settings screen of the Router’s web-based utility.)
Wireless > Wi-Fi Protected Setup
19
DRAFT - 6/25/2010
Wi-Fi Protected Setup
If you have client devices, such as a wireless adapter, that support Wi-Fi Protected Setup,
then you can use Wi-Fi Protected Setup to automatically configure wireless security for your
wireless network(s).
There are three methods available. Use the method that applies to the client device you
are configuring.
Note: Wi-Fi Protected Setup configures one client device at a time. Repeat the instructions
for each client device that supports Wi-Fi Protected Setup.
Method #1
Use this method if your client device has a Wi-Fi Protected Setup button.
1. Click or press the Wi-Fi Protected Setup button on the client device. (If Wi-Fi Protected
Setup is an on-screen option, then select it.)
2. Click the Wi-Fi Protected Setup button on this screen.
3. After the client device has been configured, click OK. Then refer back to your client device
or its documentation for further instructions.
Method #2
Use this method if your client device has a Wi-Fi Protected Setup PIN number.
1. Enter the client PIN number in the PIN field on this screen (the Router’s Wi-Fi Protected
Setup screen).
2. Click Register.
Method #3
Use this method if your client device asks for the Router’s PIN number.
1. Enter the PIN number listed on this screen. (It is also listed on the label on the bottom of the
Router.)
2. After the client device has been configured, click OK. Then refer back to your client device
or its documentation for further instructions.
At the bottom of the screen, status information for your wireless security is displayed:
Wi-Fi Protected Setup Simple-Config-State The status of the Wi-Fi Protected Setup
feature is displayed. The default is Not configured. After the Router has been configured, the
status changes to “Configured”.
Network Name (SSID) The name of the wireless network is displayed.
Security The security method of the wireless network is displayed.
Encryption The encryption method, such as TKIP or AES, is displayed.
Passphrase The passphrase for the wireless security method is displayed. It acts like a
password for access to the wireless network. (For WPA security methods, the passphrase is
also known as a WPA shared key.)
Note: If you have client devices that do not support Wi-Fi Protected Setup, note the
wireless settings, and then manually configure those client devices.
20
DRAFT - 6/25/2010
Wireless > Advanced Settings
Use this screen to set up the Router’s advanced wireless settings, which apply to all of
the Router’s wireless networks. These settings should only be adjusted by an expert
administrator as incorrect settings can reduce wireless performance.
Advanced Wireless
Wireless > Advanced Settings
Basic Rate The Basic Rate setting is not actually one rate of transmission but a series of rates
at which the Router can transmit. The Router will advertise its Basic Rate to the other wireless
devices in your network, so they know which rates will be used. The Router will also advertise that
it will automatically select the best rate for transmission. Select the appropriate option: Default,
for transmission at all standard wireless rates; 1-2Mbps, for use with older wireless technology;
All, for transmission at all wireless rates; or Wi-Fi Alt. For the Wi-Fi Alt option, basic rates are 1,
2, 5.5, 6, 11, 12, and 24 Mbps; supported rates are 9, 18, 36, 48, and 54 Mbps. If you are not sure
which rate to select, keep the default, Default.
CTS Protection Mode CTS (Clear-To-Send) Protection Mode’s default is Disabled. Select
Auto if you want the device to automatically use CTS Protection Mode when your Wireless-G
products are experiencing severe problems and are not able to transmit to the device in an
environment with heavy 802.11b traffic. This function boosts the device’s ability to catch all
Wireless-G transmissions but will severely decrease performance.
Control TX Rate The Control TX Rate should be set depending on the speed of your wireless
network. Select from a range of transmission speeds, or keep the default, Auto. When the Auto
setting is selected, the Router automatically uses the fastest possible data rate and enables
the Auto-Fallback feature, which negotiates the best possible connection speed between the
Router and a wireless device.
Wireless Afterburner To improve wireless performance when the Router is used with devices
that support SpeedBooster, select Enable. Otherwise, keep the default, Disable.
Beacon Interval Enter a value between 1 and 65,535 milliseconds. The Beacon Interval value
indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to
synchronize the wireless network(s). The default value is 100.
DTIM Interval This value, between 1 and 255, indicates the interval of the Delivery Traffic
Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window
for listening to broadcast and multicast messages. When the Router has buffered broadcast or
multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its
clients hear the beacons and awaken to receive the broadcast and multicast messages. The
default value is 1.
Fragmentation Threshold This value specifies the maximum size for a packet before data is
fragmented into multiple packets. If you experience a high packet error rate, you may slightly
increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result
in poor network performance. Only minor reduction of the default value is recommended. In
most cases, it should remain at its default value of 2346.
RTS Threshold Should you encounter inconsistent data flow, only minor reduction of the default,
2346, is recommended. If a network packet is smaller than the preset RTS threshold size, the
RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames
to a particular receiving station and negotiates the sending of a data frame. After receiving an
RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right
to begin transmission. The RTS Threshold value should remain at its default value of 2346.
WMM Support The Router supports Wi-Fi Multimedia (WMM) for Quality of Service (QoS).
When WMM Support is enabled, it provides four priority queues for different types of traffic. It
automatically maps the incoming packets to the appropriate queues based on QoS settings (in
the IP or layer 2 header). WMM provides the capability to prioritize traffic in your environment. If
you have other devices on your network that support WMM, select Enable. Otherwise, keep the
default, Disable.
21
DRAFT - 6/25/2010
Auto Power Save Delivery Unscheduled Automatic Power Save Delivery (UAPSD) is a special
power-saving mode to achieve end-to-end QoS. This option is available if you enabled WMM
Support. To use the power save feature, select Auto Power save Delivery.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Storage > Media Server
General
Server Name: Type your Media server name.
Navigation Tree: Choose the way that you want to view the navigation tree, folder structure,
and so on.
Media Receivers
Enable Sharing: Choose whether you want to enable media sharing.
Network
Restart on NIC changes: Choose whether you want to restart router when NIC changes are
received.
Storage > MediaServer
Maintenance
Logging: Choose whether you want to enable media server logging.
Clear logs: Click to clear media server logs.
View Log File: Click to view the media server log.
Restart Server: Click to restart the server.
Reset Defaults: Will remove later
Rescan Directories: Click to scan the content directory manually.
Rebuild Database: Click to delete the database file from the media server and rebuild a
new one. This may take 5 seconds.
Sharing
Rescan time: Specify how often the media server may iteratively scan the content directory.
Content Locations: Specify the location of the content directory on the media server. The
default location is already configured.
22
DRAFT - 6/25/2010
Security > Firewall
The Firewall screen is used to configure a firewall that can filter out various types of
unwanted traffic on the Router’s local network.
Firewall
Intrusion Detection Protection To use Intrusion Detection System (IDS) and Denial of Service
(DoS) protection, select Enabled. Otherwise, keep the default, Disabled.
Security > Firewall
Web Content Filtering To filter web content, keep the default, Enabled. Otherwise, select
Disabled. (This feature must be enabled to use the Website Blocking options on the Access
Restrictions > Internet Access Policy screen.)
Max Firewall Sessions Enter the maximum number of firewall sessions that will be processed
at any given time.
Max QoS Sessions Enter the maximum number of QoS sessions that will be processed at any
given time.
SIP ALG The SIP ALG feature assists VoIP phones behind the Router when NAT problems are
encountered. This feature also assists QoS (when enabled) with automatic classification of SIPand RTP-related traffic. To use the SIP ALG feature, keep the default, Enabled. Otherwise, select
Disabled.
Firewall Profile
Apply Firewall Profile For a low level of firewall protection, keep the default, Low. For a high
level of firewall protection, select High. To disable the firewall, select Off.
To configure user-based security rules, click Access Restrictions. (Refer to the “Access
Restrictions > Internet Access Policy” section for details.)
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Security > Certificates
Local Certificates: This section shows the certificates associated with the router and allows
you to import certificates.
CA Certificates: This section shows the certificates of a certificate authority chain and allows you
to import certificates.
Certificate Request: Click here to generate a certificate request, which can be filed to CA.
Security > VPN
Security > Certificates
VPN: Choose whether to enable or disable VPN.
Local Domain Name: Type the FQDN (domain name) of the router for IKE phase 1 negotiation.
Local Email Address: Type the user-FQDN(email address) of the router for IKE phase 1
negotiation.
View IKE Status: Click to view the IKE negotiation status of the configured endpoints.
VPN Log: Click to view the IKE negotiation log.
IPSec VPN Tunnel: This section shows the IPsec tunnel (endpoint) configuration.
Security > VPN
IKE Proposal: This section shows a predefined parameter set for IKE negotiation, which can be
associated with a specific IPsec tunnel.
23
DRAFT - 6/25/2010
Applications & Gaming > Single Port Forwarding
The Single Port Forwarding screen allows you to customize port services for common
applications on this screen.
When users send these types of requests to your network via the Internet, the Router will
forward those requests to the appropriate servers (computers). Before using forwarding, you
should assign static IP addresses to the designated servers.
Single Port Forwarding
To forward a port, enter the information on each line for the criteria required.
Application Select the appropriate application: HTTP (80), HTTPS (443), FTP (21),
Windows Media Player (1755), DNS (53), POP3 (110), Simple Mail Transfer (25), or
TR069 Connection Request (888).
Applications and Gaming >
Single Port Forwarding
Internal Port Enter the internal port number used by the server or Internet application. Check
with the Internet application documentation for more information.
IP Address For each application, enter the IP address of the computer that should receive the
requests.
Enabled For each application, select Enabled to enable port forwarding.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Applications & Gaming > Port Range Forwarding
The Port Range Forwarding screen allows you to set up public services on your network,
such as web servers, ftp servers, e-mail servers, or other specialized Internet applications.
(Specialized Internet applications are any applications that use Internet access to perform
functions such as videoconferencing or online gaming. Some Internet applications may not
require any forwarding.)
When users send these types of requests to your network via the Internet, the Router will
forward those requests to the appropriate servers (computers). Before using forwarding, you
should assign static IP addresses to the designated servers.
If you need to forward all ports to one computer, click the DMZ tab.
Port Range Forwarding
To forward a port range, enter the information on each line for the criteria required.
Applications and Gaming >
Port Range Forwarding
Application Select the appropriate application.
Note: If you do not see the application you want, configure the service on the Applications
& Gaming > Service screen.
IP Address For each application, enter the IP address of the computer running the specific
application.
Enabled Select Enabled to enable port forwarding for the applications you have defined.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
24
DRAFT - 6/25/2010
Applications & Gaming > DMZ
The DMZ feature allows one network computer to be exposed to the Internet for use of
a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting
forwards all the ports at the same time to one PC. The Port Range Forwarding feature is
more secure because it only opens the ports you want to have opened, while DMZ hosting
opens all the ports of one computer, exposing the computer to the Internet.
Applications and Gaming > DMZ
DMZ
Any computer whose port is being forwarded must have its DHCP client function disabled
and should have a new static IP address assigned to it because its IP address may change
when using the DHCP function.
DMZ To disable DMZ hosting, keep the default, Disabled. To expose one PC, select Enabled.
Then configure the following setting:
DMZ IP Address Enter the IP address of the computer.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Applications & Gaming > Port Range Triggering
The Port Range Triggering screen allows the Router to watch outgoing data for specific
port numbers. The IP address of the computer that sends the matching data is remembered
by the Router, so that when the requested data returns through the Router, the data is
pulled back to the proper computer by way of IP address and port mapping rules.
Port Range Triggering
To trigger a port range, enter the information on each line for the criteria required.
Application Name Enter the unique application name of the trigger.
Applications and Gaming >
Port Range Triggering
Port Start ~ Port End For each application, enter the starting and ending port numbers of the
triggering port number range. These are the ports used by initiating traffic. Check with the
Internet application documentation for the port number(s) needed.
Protocol For each application, select the appropriate protocol, TCP(6) or UDP(17).
Forwarded Port Start ~ Forwarded Port End For each application, enter the starting and ending
port numbers of the forwarded port number range. These are the ports used by incoming traffic.
Check with the Internet application documentation for the port number(s) needed.
Allow Multiple Hosts Select this option to allow multiple hosts in returned traffic.
Enabled Select Enabled to enable port triggering for the applications you have defined.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Applications & Gaming > QoS
Quality of Service (QoS) ensures better service to high-priority types of network traffic,
which may involve demanding, real-time applications, such as videoconferencing.
Note: The Router’s QoS is for upstream traffic regulation only. Downstream QoS is
usually enforced by the service provider’s headend equipment.
Applications and Gaming > QoS
25
DRAFT - 6/25/2010
QoS (Quality of Service)
Application-based QoS manages information as it is transmitted and received.
QoS To use QoS, select Enabled. Otherwise, keep the default, Disabled.
Default Queue Index Select the default queue (and priority) for applications not specified below:
1-8. (A lower value has higher priority.)
Queue Management A new window appears.
Queue Management
• Queue Index There are eight queues for each interface. You can configure the
parameters but cannot add or delete queues.
Higher index queues generally represent higher-priority queues. Queues 1-3 are Strict
Priority (WP) queues, and Queues 4-8 are priority-based Weighted Fair Queues (WFQ).
• Precedence Enter the Precedence value of this queue relative to the others. A lower
value indicates higher precedence.
• Scheduler Select the scheduling algorithm: SP, WFQ, or WRR (Weighted Round
Robin). The default is SP.
• Dropper Select the dropping algorithm used if there is congestion: RED (Random
Early Detection), DT (Drop Tail), or WRED (Weighted RED). The default is WRED.
Applications and Gaming > QoS >
Queue Management
• Weight When WFQ or WRR is used, this option is available and used only for queues
of equal precedence. Queues 4-6 have equal precedence, and Queues 7-8 have equal
precedence. Queues 1-3 have higher precedence than Queues 4-6, while Queues 4-6
have higher precedence than Queues 7-8.
• Shaping If the Shaping rate is greater than or equal to 100, then it is the percentage
of physical bandwidth. If the Shaping rate is less than 100, then it is the rate in bits per
second. A value of -1 indicates no shaping. The default is -1.
• Burst Size Enter the Burst Size in bytes (1 to 10485760). For both leaky bucket (constant
rate shaping) and token bucket (variable rate shaping) algorithms, the Burst Size value
is the bucket size and the maximum burst size. If you set this value to zero, then the
Router will use the system default Burst Size, which is the current Shaping rate divided
by eight. The default is 0.
Click Save Settings to apply your changes, or click Back to QoS to cancel your changes
and return to the QoS screen.
Summary
The QoS rules are displayed with the following information: Port, Filters/Target, Queue
Index, Marks and On (status).
To move, edit, or delete a rule, select the entry (its color will change).
Move Up To move a QoS rule up in precedence, click this option.
Move Top To move a QoS rule to highest in precedence, click this option.
Move Down To move a QoS rule down in precedence, click this option.
Move Bottom To move a QoS rule lowest in precedence, click this option.
Delete To delete a QoS rule, click this option.
Edit Rule To change a QoS rule, click this option.
New Rule To create a new QoS rule, click this option.
If you click Edit Rule or New Rule, a different screen appears.
26
DRAFT - 6/25/2010
QoS (Quality of Service)
• Enable To enable this QoS rule, select the check box. Otherwise, leave the check box
blank.
• Classification Sources Select All Sources, Local Router, All LAN Ports that traffic
will come from, or a specific LAN port: Ethernet Ports 1-5 or WLAN SSID networks. The
default is All Sources.
• Ethernet Type Select None, IP (0x0800), ARP (0x0806), PPPoE Discovery Stage
(0x8863), PPPoE Session State (0x8864), or EAPOL (0x888e).
• Protocol If you selected IP (0x0800) for the Ethernet Type setting, then select the
appropriate Protocol: None, ICMP (1), IGMP (2), TCP (6), or UDP (17).
Depending on the Protocol you selected, the following settings may be available:
• Destination IP Enter the Destination IP address, if applicable as a filter condition.
• Destination Subnet Mask Enter the Destination subnet mask, if applicable as a filter
condition.
QoS > Add New Rule
• Destination Port If you selected TCP or UDP for the Protocol setting, enter the
Destination port range, if applicable as a filter condition.
• Source IP Enter the Source IP address of the local computer, if applicable as a filter
condition.
• Source Subnet Mask Enter the Source subnet mask, if applicable as a filter condition.
• Source Port If you selected TCP or UDP for the Protocol setting, enter the Source port
range, if applicable as a filter condition.
• Source MAC Enter the Source MAC address of the local computer, if applicable as a filter
condition.
• Source MAC Mask Enter the Source MAC Mask, if applicable as a filter condition. If you
leave this setting blank, then this mask will be ignored.
• Source Vendor Class ID If applicable as a filter condition, enter the Source Vendor Class ID
in the host’s DHCP request.
• Source Client ID If applicable as a filter condition, enter the Source Client ID in the host’s
DHCP request.
• Source User Class ID If applicable as a filter condition, enter the Source User Class ID in the
host’s DHCP request.
• DSCP If applicable as a filter condition, enter the DSCP value of the LAN’s incoming packet.
• Ethernet Priority If applicable as a filter condition, enter the Ethernet Priority of the LAN’s
incoming packet.
• VLAN ID If applicable as a filter condition, enter the VLAN ID of the LAN’s incoming packet.
• Ethernet Priority Mark (optional) To mark outgoing packets with a specific 802.1p value,
enter the value in the field provided.
• DSCP Mark (optional) To mark outgoing packets with a specific DSCP value, enter the value
in the field provided.
• Target Interface (optional) All WAN connections and PVC/VLAN bridges are listed. Select
the appropriate interface. The Router will direct matching packets to this outgoing interface.
27
DRAFT - 6/25/2010
• Queue Index Traffic priority applies to LAN-to-WAN traffic only. Higher priority traffic is
guaranteed available bandwidth. This is useful for simultaneous activities that put a heavy
load on the network (for example, a VoIP phone call during large file downloads). Select the
appropriate Queue Index (and priority): 1 High-8 (a lower value means higher priority).
Note: Traffic from the Router’s voice lines are automatically assigned highest priority.
You can update parameters, such as the Ethernet Priority Mark setting, according to your
service provider’s request.
Click Add Rule or Save Rule to save your changes, or click Cancel Changes to cancel your
changes and return to the original QoS screen.
On the original QoS screen, click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Applications & Gaming > Service
The Service screen allows you to add services.
Service/Application
Service Table
The services are displayed with the following information: Service Name, Protocol, Ports/
Types, and Action. To delete a user-defined service, click Delete. (Default services cannot
be deleted.)
To view additional services, click Extended View. To return to the Basic View, click Basic
View.
Service Entry
Service Name Enter a name for the new service.
Protocol Select the appropriate protocol: TCP(6), UDP(17), ICMP, ESP(50), AH(51), GRE(47),
IGMP(2), PIM-DM(103), or IPCOMP(108).
Applications and Gaming > Service
Ports Enter the starting and ending port numbers.
ICMP Type Enter the appropriate number, 1-255, which is valid only for ICMP.
IGMP Type Enter the appropriate number, 1-255, which is valid only for IGMP.
Click Add Service to add a new service, or click Cancel Changes to cancel your changes.
28
DRAFT - 6/25/2010
Administration > Management
The Administration > Management screen allows the network’s administrator to manage
specific Router functions for access and security.
Gateway Access
Local Gateway Access
To ensure the Router’s security, you will be asked for your username and password when you
access the Router’s web-based utility. The default username and password are admin.
Router Username Enter the default Router Username, admin.
Router Password Cisco recommends that you change the default Router Password, admin, to
one of your choice.
Re-enter to Confirm Enter the Router Password again to confirm.
Administration > Management
Remote Gateway Access
Remote Management To permit remote access of the Router, from outside the local network,
select Enabled. Otherwise, keep the default, Disabled.
Management Port Enter the port number that will be open to outside access.
Management Protocol Select the appropriate protocol, HTTP or HTTPS.
Note: When you are in a remote location and wish to manage the Router, enter
https://:port or http://:port. Enter
the Router’s specific Internet IP address in place of , and enter
the Management Port number in place of the word port.
Remote User Name Enter the login user name for remote management.
Remote User Password Enter the login password for remote management.
IGMP
Internet Group Multicast Protocol (IGMP) is used to establish membership in a multicast
group and is commonly used for multicast streaming applications. For example, you may
have Internet Protocol Television (IPTV) with multiple set-top boxes on the same local
network. These set-top boxes have different video streams running simultaneously, so you
should use the IGMP feature of the Router.
IGMP Proxy IGMP forwarding (proxying) is a system that improves multicasting for LAN-side
clients. If the clients support this option, keep the default, Enabled. Otherwise, select Disabled.
IGMP Querier Version Select: Version 1, Version 2, or Version 3. The default is Version 2.
Query Interval This option is valid when IGMP Proxy is enabled. Enter the number of seconds
between queries. The default is 125 seconds.
Querier Immediate Leave Select Enabled, if you use IPTV applications and want to allow
immediate channel swapping or flipping without lag or delays. Otherwise, keep the default,
Disabled.
29
DRAFT - 6/25/2010
UPnP
Universal Plug and Play (UPnP) allows Windows XP and Vista to automatically configure
the Router for various Internet applications, such as gaming and videoconferencing.
UPnP If you want to use UPnP, keep the default, Enabled. Otherwise, select Disabled.
Note: IGMPv2 is enabled by default, and v3 is supported. IGMP Snooping is enabled by
default for all bridges.
Administration > Log
The Router can keep logs of traffic and events for your Internet connection.
Basic Settings
Log To disable the Log function, select Disabled. To monitor traffic between the network and
the Internet, keep the default, Enabled. With logging enabled, you can choose to view temporary
logs.
Log Severity Select the severity level of the log events you want to view: Informational,
Warning (default), or Critical.
System Log Server To enable system log server support, enter the IP address of the system log
server. To disable system log server support, leave this setting blank.
Advanced Settings
Category: Choose the category of logs that you want to view (firewall, security, system control,
network, QoS, user authorization, VPN, routing, or certification).
Logging Size: Type the file size that you want to use for logging files here. The default value is
256 KB.
Administration > Log
Firewall Logging size: Type the maximum number of rows to include in a firewall log here. The
default value is 1000 rows.
Email Alert
Email Alerts (For Warning Events) To enable E-Mail Alerts for Warning-level events, select
Enabled. Otherwise, keep the default, Disabled.
SMTP Mail Server Enter the address (domain name) or IP address of the Simple Mail Transport
Protocol (SMTP) server for outgoing e-mail.
User Name Enter the User Name for SMTP authentication.
Password Enter the Password for SMTP authentication.
Email to Address Enter the e-mail address that will receive alert logs.
Email From Address Enter the return address for the e-mail alerts. (This can be a dummy
address.)
30
DRAFT - 6/25/2010
Search Log
Category: Choose the category of logs that you want to view (firewall, security, system control,
network, QoS, user authorization, VPN, routing, certification).
Log Severity: Choose the severity of messages that you want to include in the logs here..
Policy: TBD.
Message: If you want to see only messages that contain a certain keyword, type that keyword
here.
IP Address: Use these fields to restrict the logs so that you only see messages to or from certain
IP addresses.
MAC address: Use these fields to restrict the logs so that you only see messages to or from
certain MAC addresses.
DateTime: Use the fields to restrict the logs so that you only see messages that happened
during a certain date range.
Click Save Settings to apply your changes. Click Clear Event Log to clear all of the events.
Click Refresh to update the on-screen information.
Administration > IPPing
The ping test allows you to check the connections of your network devices, including
connection to the Internet.
Ping Test
Ping Test Parameters
The ping test checks the status of a connection.
Target IP/FQDN Enter the IP address or Fully Qualified Domain Name (FQDN) that you want to
ping. This can be either a local (LAN) or Internet (WAN) IP address.
Administration >IPPing
Ping Size Enter the packet size you want to use. The default is 32 bytes.
Number of Pings Enter how many times you want to ping. The default is 3.
Ping Timeout Enter the number of milliseconds before the ping test will time out. The default is
5000 milliseconds.
Ping Result The results of the ping test are displayed.
To run the test, click Start Test. Click Refresh to update the on-screen information.
Administration > IP Traceroute
Traceroute test parameters
Target IP/FQDN: Type the destination of the traceroute, as an IP address or a domain name.
Traceroute Size: Type the ICMP packet size, in bytes. If the MTU is lower than this value and
fragments are not allowed, an ICMP error message appears.
Number of Traceroutes: For each hop, the traceroute application may send multiple packets.
Specify the number of traceroutes here.
Administration > IPTracert
Max Number of hop: Type the maximum number of hops allowed here. If the number of hops is
greater than this value, an ICMP error message appears.
Traceroute Timeout: Type the maximum waiting time between the ICMP request and the ICMP
response.
31
DRAFT - 6/25/2010
Administration > Self Diagnostics
Diagnostics Trigger:
Choose whether you want to enable the diagnostics trigger.
VoD Monitor Trigger:
Choose whether you want the MoCA network performance to be recorded in the router
persistence log along with a TR-069 parameter for troubleshooting analysis when
necessary.
Diagnostics Settings
Schedule option: Choose Enable if you want self-diagnostics to occur periodically, or
choose Disable to perform the self-diagnostics immediately, followed by the correction
procedure if enabled.
Diagnosis interval: Choose how often the diagnostics tests should occur. The minimum
interval is one day.
Start time: Enter the time that the diagnostics tests should start here, in 24-hour format.
WAN IP Polling Interval: Enter the time interval that should pass before the next WAN IP
check, in seconds.The default value is 1 hour (3600 seconds).
Bandwidth Polling Interval: Enter the time interval that should pass before the next
bandwidth polling test.
Administration > Self Diagnosis
Enable Correction: Choose Enable if the router should attempt to recover from any
errors that it encounters, or choose Disable if you router should only log the error without
attempting to recover.
WAN DNS Domain: Type the domain that is used to test DNS.
Correction Settings
Enable Factory Reset: Choose whether or not to allow self diagnostics to reset the router
to the factory default. Choosing Enable will delete the user’s configuration.
Factory Reset Trigger: Errors that are detected by self diagnistics may trigger the router
to reboot. Specify how many reboots can take place before the router resets itself.
Correction Start Time: Self diagnostics corrections do not take place immediately after
the error is detected. Specify when a self diagnostics correct should take place.
Diagnostics Threshold
Memory Threshold: Specify the memory utilization that can be reached before corrective
action is taken.
WAN BW Threshold: Specify the bandwidth utilization that can be reached before
corrective action is taken.
MoCA Rate Threshold: Specify the MoCA rate utilization that can be reached before
corrective action is taken.
Diagnostics Cases
TBHR: This test ensures that there are sufficient internal resources for the router to
operate optimally. The CPU and memory utilization snapshot should be taken during the
self-diagnostics operation or using a polling interval (BANDWIDTH_POLLING _INTERVAL).
TWANIP: This test ensures that the router has a WAN IP assigned.
TLANMOCA: This test only applies if the MoCA interface is enabled and active. It ensures
that the transmission rate for both Tx and Rx should be greater than 180Mbps.
32
DRAFT - 6/25/2010
TLANIP: This test ensures that all LAN devices which are currently attached and active
have an IP assigned correctly. One method to determine if the LAN device is active or
inactive is by sending an ARP request from the router.
TWANTYPE: This test ensures that only one WAN interface is be enabled and active at
any time it is in a Connected state. Both WAN interfaces can be enabled, if they are in a
Disconnected state.
TWANIPCON: This test ensures that the router has WAN IP connectivity. The IP
connectivity is validated via ping tests to both the default gateway (the first hop network
router) and the VZ DNS server.
TLANETH: This test ensures that all the Ethernet ports with devices attached are operating
optimally, for example, no hardware port failures, excessive framing or CRC errors, and so
on. This test only applies if the LAN Ethernet interface is enabled.
TLANBW: This test ensures that at least one of the enabled LAN interfaces can send
or receive network traffic based on the delta bytes count. The delta bytes count is the
difference between the current value and the last recorded poll value. The default poll
interval is every hour.
TWANMOCA: This test ensures that the transmission rate for both Tx and Rx is greater
than MoCA threshold level for expected performance. This test only applies if the MoCA
interface is enabled.
TWANBW: This test ensures that the WAN interface can send and receive network traffic
based on the delta bytes count. The delta bytes count is the difference between the
current value and the last recorded polled value. The poll interval is cinfigurable through
CMS; the default interval is every hour.
TLANWIFI: This test ensures that the WiFi signal level (RSSI) is acceptable for each WiFi
device that is visible in this interface.
TLANIPCONSTB: This test ensures that all set-top boxes that are attached and active on
this WAN interface respond successfully to the PING test operation.
TWANETH: This test ensures that the WAN Ethernet port is operating optimally, for exampl,
no hardware issue, excessive framing errors, CRC errors, and so on.
TLANTYPE: This test ensures that at least one of the LAN interfaces is enabled and active.
TLANDEV: This test determines how many LAN devices are currently attached and active
on the various LAN interfaces (for example, LAN Ethernet, LAN MoCA, and LAN WiFi) of the
BHR. The device count determination should be done at the physical medium level and
NOT at the IP level. A LAN device must be included in the count if it has been attached and
active for more than 30 minutes. (This is due to the BHR implementation of record updates.)
Diagnostics Action
Use this area to specify the action that should take if any of the following conditions occur.
For example, for CBHR_MEM, if the memory utilization is less than the memory threshold,
then the router will perform the associated action.
The conditions are:
CBHR_MEM: The memory utilization is less than the memory threshold.
CWANTYPE: Only one WAN interface is enabled, or both WAN interfaces are enabled but
disconnected.
CWANMOCA_RATE: The transmission rate (Tx and Rx) is greater than the MoCA rate
threshold.
CWANIP: The WAN IP address is assigned.
CLANMOCA_PORT: The physical port is operational with no hardware failure.
CLANETH_PORT: All the LAN Ethernet ports which have devices attached are operating
optimally, with no failures.
33
DRAFT - 6/25/2010
CLANDEV: One or more LAN devices are attached and active.
CLANBW: Both the delta number of bytes sent and the number of bytes received are
greater than the LAN bandwidth threshold.
CBHR_CPU: The CPU utilization is less than the CPU threshold.
CWANMOCA_PORT: The physical MoCA port is operational with no hardware failure.
CWANETH_PORT: The Ethernet port is operational, with no hardware failure.
CWANIPCON_PNGDF: The default gateway responds to to the ICMP PING.
CWANIPCON_DNSR: The DNS server responds to ICMP PING.
CLANTYPE: One or more of the LAN interface are enabled (LAN MoCA, LAN Ethernet, and
LAN WiFi).
CLANMOCA_RATE: Both transmission rates (Tx and Rx) are greater than the MoCA rate
threshold.
CLANWIFI_PORT: The WiFi interface is operating optimally, with no hardware issues or
errors.
CLANIP: All LAN devices have an IP address assigned.
CLANIPCONSTB_PNG: All attached and active set-top boxes respond to the ICMP PING.
Administration > Backup
The Backup screen allows you to back up or restore the Router’s settings using a configuration
file.
Backup Configuration
Backup To save the Router’s settings in a configuration file, click this button and follow the
on-screen instructions.
Note: The voice settings will not be saved in the configuration file.
Administration > Backup
Restore Configuration
To use this option, you must have previously backed up its configuration settings.
Please select a file to restore Click Browse and select the Router’s configuration file.
Restore To restore the Router’s configuration settings, click this button and follow the
on-screen instructions.
Administration > Factory Defaults
The Factory Defaults screen allows you to restore the Router’s configuration to its factory
default settings, except for the voice settings. (An alternative method is to press and hold
the Reset button on the Router’s back panel for approximately ten seconds.)
Note: Restoring factory defaults deletes custom settings except for the voice settings.
Note your custom settings before clicking the Restore Factory Defaults button.
Administration > Factory Defaults
34
DRAFT - 6/25/2010
Factory Defaults
Restore Factory Defaults To reset settings to the default values, click this button and follow
the on-screen instructions. Any custom Router settings you have saved (except for the voice
settings) will be lost when the default settings are restored.
Administration > Upgrade
The Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the
firmware unless you are experiencing problems with the Router or the new firmware has a
feature you want to use.
Note: The Router may lose the settings you have customized. Before you upgrade its
firmware, write down all of your custom settings. After you upgrade its firmware, you will
have to re-enter all of your configuration settings.
Administration > Upgrade
Firmware Upgrade
Before upgrading the firmware, download the Router’s firmware upgrade file from the
Cisco website, www.linksysbycisco.com/international. Then extract the file.
Please Select a File to Upgrade Click Browse and select the extracted firmware upgrade
file.
Start to Upgrade After you have selected the appropriate file, click this button, and follow the
on-screen instructions.
Note: In rare cases (such as a power failure), the firmware upgrade may fail. If that
happens, the Router will enter recovery mode and automatically download firmware from
your service provider’s provisioning server.
Administration > Reboot
The Reboot screen allows you to restart the Router through the web-based utility.
Reboot
Click Reboot Box to restart the Router. The restart will terminate the Internet connection.
Administration > Logout
Administration > Reboot
The Logout screen allows you to properly exit the web-based utility.
Logout
Click Logout to exit the web-based utility.
Administration > Logout
35
DRAFT - 6/25/2010
Administration > IGMP
IGMP Access Policy Control
IGMP Access Policy Table:
Needs text.
IGMP Access Policy Rule
IGMP Access control: Choose whether to allow multicast traffic of a specific multicast
group.
Administration > IGMP
Group Address: Type the IP address of multicast traffic which is affected the rule.
Address Mask: Type the network mask of the IP address specified in the Group Address.
Allow Traffic: Choose whether to allow multicast traffic. This rule defines how the router
will respond to a multicast route from outside.
IGMP Hosts
IGMP Host Table
Needs text.
Status > Internet
The Internet screen displays information about the Router and its current settings.
Router Information
Manufacturer OUI The manufacturer ID number is displayed.
Serial Number The serial number of the Router is displayed.
Hardware Version The version number of the Router’s hardware is displayed.
Software Version The version number of the Router’s software is displayed.
System Uptime The length of time the Router has been active is displayed.
Local Time The date and time of the Router are displayed.
Status > Internet
Internet Connection
This section shows the current information for enabled connections. The table lists the
following information about each connection: Interface, MAC/IP/Subnet, Router, DNS, and
Status.
For DHCP connections, you can manually renew or release them. For PPP-type connections,
you can manually connect or disconnect them.
Click Refresh to update the on-screen information.
36
DRAFT - 6/25/2010
Status > MoCA
MoCA WAN Info
This section p rovides information about the MoCA WAN connection.
MoCA LAN Info
This section provides information about the MoCA LAN connection.
Status > Local Network
The Local Network screen displays information about the local network.
Local Network
IP Address The Router’s IP address, as it appears on your local network, is displayed.
Subnet Mask The Subnet Mask of the Router is displayed.
DHCP Server The status of the Router’s DHCP server function is displayed.
Starting IP Address For the range of IP addresses used by devices on your local network, the
starting IP address is displayed.
Ending IP Address For the range of IP addresses used by devices on your local network, the
ending IP address is displayed.
DHCP Lease Time The length of time for the DHCP lease setting is displayed.
DHCP Client Table
Status > MoCAInfo
The table displays DHCP, static, and dynamic (found by ARP) types of clients. It describes
the devices that have been assigned IP addresses by the Router. For each device, the
table lists the following information: Interface, MAC Address, IP Address, Host Name, and
Lease Remaining (how much time is left for the current IP address).
IGMP Group Table
The table describes the IGMP configuration of the Router (if configured).
Click Refresh to update the on-screen information.
Statistics
This section provides information about transmitted and received data.
Ethernet Port Mode
This section shows the configuration of the LAN interface status, duplex mode and rate.
Status > Local Network
37
DRAFT - 6/25/2010
Status > Wireless
The Wireless screen displays information about your wireless network(s).
Wireless Network
For each wireless network, the following is displayed:
SSID The name of the wireless network is displayed.
MAC Address The MAC address of the Router’s local, wireless interface is displayed.
Security The wireless security method is displayed (if used).
Status > Wireless
SSID Broadcast The SSID broadcast setting is displayed.
Click Refresh to update the on-screen information.
Status > Bridges
The Bridges screen displays information about the PVC/VLAN and default LAN bridges
of the Router
Bridges
The total number of bridges and their descriptions are displayed.
Port (Name/Type) The port name or type is displayed.
Status > Bridge
Learned Host (MAC/IP/Time to Expire) The MAC address, IP address, or Time to Expire duration
is displayed.
IGMP (Group Address/Time to Expire) The IGMP Group Information of this port is displayed.
Click Refresh to update the on-screen information.
Status > ARP Table
ARP Cache Table
This section displays ARP entries for the listed interface. It includes IP address,
corresponding MAC address and length of time active.
Status > Media Server
Status > ARP Table
Media Server
This section provides information about the status of the media server.
Status > MediaServer
38
DRAFT - 6/25/2010
Troubleshooting
Your computer cannot connect to the Internet.
Follow the instructions until your computer can connect to the Internet:
• Make sure that the Router is powered on. The Power LED should be green and not
flashing.
• If the Power LED is flashing, then power off all of your network devices, including the
Router and computers. Then power on each device in the following order:
1. Router
2. Computer
• Check the LEDs on the front panel of the Router. Make sure the Power, DSL, and at least
one of the numbered LEDs are lit. If they are not, then check the cable connections. The
computer should be connected to one of the ports numbered 1-4 on the Router, and
the Line port of the Router must be connected to the ADSL line.
When you double-click the web browser, you are prompted for a
user name and password. If you want to get rid of the prompt, follow
these instructions.
Launch the web browser and perform the following steps (these steps are specific to
Internet Explorer but are similar for other browsers):
1. Select Tools > Internet Options.
2. Click the Connections tab.
3. Select Never dial a connection.
4. Click OK.
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same on both the computer and the
Router. If you have enabled wireless security, then make sure the same security method
and key are used by both the computer and the Router.
You need to modify the advanced settings on the Router.
Open the web browser (for example, Internet Explorer or Firefox), and enter the Router’s
IP address in the address field (the default IP address is 192.168.1.1). When prompted,
complete the User name and Password fields (the default user name and password is
admin). Click the appropriate tab to change the settings.
Web: Refer to the Cisco website, www.linksysbycisco.com/international, if your
questions are not addressed here.
39
DRAFT - 6/25/2010
Specifications
Model
RMN302
Interfaces
COAX
MoCA LAN; MoCA WAN
WAN
Ethernet WAN Interface RJ-45 Port
LAN
Ports (RJ-45); Ethernet 10/100/1000 BASE-T with
Auto-Crossover
USB
2 USB 2.0 (host) Ports
Wi-Fi
IEEE 802.11b/g/n
802.1x Authentication
External RADIUS Authentication
WPA2 and WPA Access
WEP, AES & TKIP Encryption
WPA/WEP Mixed Mode
Wi-Fi Multimedia Support (WMM)
Multiple SSIDs
MAC Address Filtering Integrated
WPS (Push button & PIN entry)
Regional Channel Setting
LEDs
Power, Internet ,WAN, WAN MoCA, LAN MoCA, LAN1~4,
WLAN, USB1&2, WPS
Buttons
On/Off, Reset, WPS
Mounting
Desktop and Wall Mount
Environmental
Dimensions
220 mm x 42 mm x 175 mm (8.66 in. x 1.65 in. x 6.89 in.)
Weight
400 g (14.11 oz)
Power
110-240 VAC 50/60 Hz Switching Power Supply;
12 VDC, 2 A Output
Certification
FCC Part 68, Part 15, Class B, UL1950, CSA, European EMC
& Immunity, CE Mark, Industry-Canada
Operating Temp. 0° to 40°C (32° to 104°F)
Storage Temp.
0° to 70°C (32° to 158°F)
Humidity
20 to 80% Noncondensing
Specifications are subject to change without notice.
40
DRAFT - 6/25/2010
Software License Agreement
Software in Cisco Products
This product from Cisco-Cisco LLC or from one of its affiliates Cisco
Systems-Cisco (Asia) Pte Ltd. or Cisco-Cisco K.K. (“Cisco”) contains
software (including firmware) originating from Cisco and its suppliers
and may also contain software from the open source community. Any
software originating from Cisco and its suppliers is licensed under the
Cisco Software License Agreement contained at Schedule 1 below. You
may also be prompted to review and accept that Cisco Software License
Agreement upon installation of the software
Any software from the open source community is licensed under the
specific license terms applicable to that software made available by Cisco
at www.linksysbycisco.com/gpl or as provided for in Schedules 2, 3 and
4 below.
Where such specific license terms entitle you to the source code of such
software, that source code is upon request available at cost from Cisco
for at least three years from the purchase date of this product and may
also be available for download from www.linksysbycisco.com/gpl. For
detailed license terms and additional information on open source software
in Cisco products please look at the Cisco public web site at: www.
linksysbycisco.com/gpl/ or Schedules 2, 3 or 4 below as applicable.
BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE
PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING
TO BE BOUND BY THE SOFTWARE LICENSE AGREEMENTS BELOW. IF
YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT
DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF
ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE
RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU
PURCHASED SUCH PRODUCT OR SOFTWARE.
Software Licenses
The software Licenses applicable to software from Cisco are made
available at the Cisco public web site at: www.linksysbycisco.com. For
your convenience of reference, a copy of the Cisco Software License
Agreement and the main open source code licenses used by Cisco in its
products are contained in the Schedules below.
Schedule 1 - Cisco Software License
Agreement
THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC
OR ONE OF ITS AFFILIATES CISCO SYSTEMS-LINKSYS (ASIA) PTE LTD.
OR CISCO-LINKSYS K.K. (“CISCO”) LICENSING THE SOFTWARE INSTEAD
OF CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING THE
SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE,
YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF
YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT
DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF
ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE
RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU
PURCHASED SUCH PRODUCT OR SOFTWARE.
License. Subject to the terms and conditions of this Agreement,
Cisco grants the original end user purchaser of the Cisco product
containing the Software (“You”) a nonexclusive license to use the
Software solely as embedded in or (where authorized in the applicable
documentation) for communication with such product. This license
may not be sublicensed, and is not transferable except to a person or
entity to which you transfer ownership of the complete Cisco product
containing the Software, provided you permanently transfer all rights
under this Agreement and do not retain any full or partial copies of
the Software, and the recipient agrees to the terms of this Agreement.
“Software” includes, and this Agreement will apply to (a) the software of
Cisco or its suppliers provided in or with the applicable Cisco product,
excluding technology from the open source community, and (b) any
upgrades, updates, bug fixes or modified versions (“Upgrades”) or backup
copies of the Software supplied to You by Cisco or an authorized reseller,
provided you already hold a valid license to the original software and have
paid any applicable fee for the Upgrade.
Protection of Information. The Software and documentation contain
trade secrets and/or copyrighted materials of Cisco or its suppliers.
You will not copy or modify the Software or decompile, decrypt, reverse
engineer or disassemble the Software (except to the extent expressly
permitted by law notwithstanding this provision), and You will not disclose
or make available such trade secrets or copyrighted material in any form to
any third party. Title to and ownership of the Software and documentation
and any portion thereof, will remain solely with Cisco or its suppliers.
Collection and Processing of Information. You agree that Cisco
and/or its affiliates may, from time to time, collect and process information
about your Cisco product and/or the Software and/or your use of either
in order (i) to enable Cisco to offer you Upgrades; (ii) to ensure that your
Cisco product and/or the Software is being used in accordance with the
terms of this Agreement; (iii) to provide improvements to the way Cisco
delivers technology to you and to other Cisco customers; (iv) to enable
Cisco to comply with the terms of any agreements it has with any third
parties regarding your Cisco product and/or Software and/or (v) to
enable Cisco to comply with all applicable laws and/or regulations, or the
requirements of any regulatory authority or government agency. Cisco
and/ or its affiliates may collect and process this information provided
that it does not identify you personally. Your use of your Cisco product
and/or the Software constitutes this consent by you to Cisco and/or its
affiliates’ collection and use of such information and, for EEA customers, to
the transfer of such information to a location outside the EEA.
Software Upgrades etc. If the Software enables you to receive
Upgrades, you may elect at any time to receive these Upgrades either
automatically or manually. If you elect to receive Upgrades manually or
you otherwise elect not to receive or be notified of any Upgrades, you may
expose your Cisco product and/or the Software to serious security threats
and/or some features within your Cisco product and/or Software may
become inaccessible. There may be circumstances where we apply an
Upgrade automatically in order to comply with changes in legislation, legal
or regulatory requirements or as a result of requirements to comply with
the terms of any agreements Cisco has with any third parties regarding
your Cisco product and/or the Software. You will always be notified of any
Upgrades being delivered to you. The terms of this license will apply to
any such Upgrade unless the Upgrade in question is accompanied by a
separate license, in which event the terms of that license will apply.
Open Source Software. The GPL or other open source code
incorporated into the Software and the open source license for such source
code are available for free download at http://www.linksysbycisco.
com/gpl. If You would like a copy of the GPL or other open source code in
this Software on a CD, Cisco will mail to You a CD with such code for $9.99
plus the cost of shipping, upon request.
Term and Termination. You may terminate this License at any time
by destroying all copies of the Software and documentation. Your rights
under this License will terminate immediately without notice from Cisco if
You fail to comply with any provision of this Agreement.
Limited Warranty. The warranty terms and period specified in the
applicable Cisco Product User Guide shall also apply to the Software.
41
DRAFT - 6/25/2010
Disclaimer of Liabilities. IN NO EVENT WILL CISCO OR ITS SUPPLIERS
BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL,
INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES,
REGARDLESS OF CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF
OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE,
EVEN IF CISCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO EVENT WILL CISCO’ LIABILITY EXCEED THE AMOUNT
PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply
even if any warranty or remedy under this Agreement fails of its essential
purpose. Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to You.
To protect your rights, we need to make restrictions that forbid anyone
to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
Export. Software, including technical data, may be subject to U.S. export
control laws and regulations and/or export or import regulations in other
countries. You agree to comply strictly with all such laws and regulations.
Also, for each author’s protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software.
If the software is modified by someone else and passed on, we want
its recipients to know that what they have is not the original, so that any
problems introduced by others will not reflect on the original authors’
reputations.
U.S. Government Users. The Software and documentation qualify as
“commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All
Government users acquire the Software and documentation with only
those rights herein that apply to non-governmental customers.
General Terms. This Agreement will be governed by and construed in
accordance with the laws of the State of California, without reference to
conflict of laws principles. The United Nations Convention on Contracts
for the International Sale of Goods will not apply. If any portion of this
Agreement is found to be void or unenforceable, the remaining provisions
will remain in full force and effect. This Agreement constitutes the
entire agreement between the parties with respect to the Software and
supersedes any conflicting or additional terms contained in any purchase
order or elsewhere.
END OF SCHEDULE 1
For example, if you distribute copies of such a program, whether gratis or
for a fee, you must give the recipients all the rights that you have. You must
make sure that they, too, receive or can get the source code. And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2)
offer you this license which gives you legal permission to copy, distribute
and/or modify the software.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program
will individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must be
licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification
follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0.
Schedule 2
If this Cisco product contains open source software licensed under Version
2 of the “GNU General Public License” then the license terms below in this
Schedule 2 will apply to that open source software. The license terms
below in this Schedule 2 are from the public web site at http://www.gnu.
org/copyleft/gpl.html
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright Š 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
1.
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software–
to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and
to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Lesser General
Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for this service if
you wish), that you receive source code or can get it if you want it, that you
can change the software or use pieces of it in new free programs; and that
you know you can do these things.
42
2.
This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed
under the terms of this General Public License. The “Program”, below,
refers to any such program or work, and a “work based on the Program”
means either the Program or any derivative work under copyright
law: that is to say, a work containing the Program or a portion of it,
either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation
in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered
by this License; they are outside its scope. The act of running the Program
is not restricted, and the output from the Program is covered only if its
contents constitute a work based on the Program (independent of having
been made by running the Program). Whether that is true depends on
what the Program does.
You may copy and distribute verbatim copies of the Program’s source
code as you receive it, in any medium, provided that you conspicuously
and appropriately publish on each copy an appropriate copyright
notice and disclaimer of warranty; keep intact all the notices that refer
to this License and to the absence of any warranty; and give any other
recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you
may at your option offer warranty protection in exchange for a fee.
You may modify your copy or copies of the Program or any portion of it,
thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a. You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b.
You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any part
thereof, to be licensed as a whole at no charge to all third parties
under the terms of this License.
DRAFT - 6/25/2010
c.
If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide
a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but does
not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the Program,
and can be reasonably considered independent and separate works
in themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on the terms
of this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote
it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based
on the Program.
4.
5.
6.
7.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on
a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3.
You may copy and distribute the Program (or a work based on it, under
Section 2) in object code or executable form under the terms of Sections 1
and 2 above provided that you also do one of the following:
a. Accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for
software interchange; or,
b.
Accompany it with a written offer, valid for at least three years, to give
any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable
copy of the corresponding source code, to be distributed under
the terms of Sections 1 and 2 above on a medium customarily
used for software interchange; or,
c.
Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed
only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access
to copy from a designated place, then offering equivalent access to
copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy
the source along with the object code.
You may not copy, modify, sublicense, or distribute the Program except
as expressly provided under this License. Any attempt otherwise to copy,
modify, sublicense or distribute the Program is void, and will automatically
terminate your rights under this License. However, parties who have
received copies, or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full compliance.
You are not required to accept this License, since you have not signed
it. However, nothing else grants you permission to modify or distribute
the Program or its derivative works. These actions are prohibited by law
if you do not accept this License. Therefore, by modifying or distributing
the Program (or any work based on the Program), you indicate your
acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Program or works based on it.
Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms
and conditions. You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties to this License.
If, as a consequence of a court judgment or allegation of patent infringement
or for any other reason (not limited to patent issues), conditions are imposed
on you (whether by court order, agreement or otherwise) that contradict
the conditions of this License, they do not excuse you from the conditions
of this License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as
a consequence you may not distribute the Program at all. For example, if a
patent license would not permit royalty-free redistribution of the Program
by all those who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License would be to refrain
entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public
license practices. Many people have made generous contributions to
the wide range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
8.
9.
If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add an
explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus excluded.
In such case, this License incorporates the limitation as if written in the
body of this License.
The Free Software Foundation may publish revised and/or new versions
of the General Public License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and
“any later version”, you have the option of following the terms and
conditions either of that version or of any later version published by the
Free Software Foundation. If the Program does not specify a version
number of this License, you may choose any version ever published
by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs
43
DRAFT - 6/25/2010
10. whose distribution conditions are different, write to the author to ask for
permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes
make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 2
Schedule 3
If this Cisco product contains open source software licensed under
Version 2.1 of the “GNU Lesser General Public License” then the license
terms below in this Schedule 3 will apply to that open source software.
The license terms below in this Schedule 3 are from the public web site at
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the
successor of the GNU Library Public License, version 2, hence the version
number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public Licenses are
intended to guarantee your freedom to share and change free software—
to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially
designated software packages—typically libraries—of the Free Software
Foundation and other authors who decide to use it. You can use it too,
but we suggest you first think carefully about whether this license or
44
the ordinary General Public License is the better strategy to use in any
particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not
price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish); that you receive source code or can get it if you
want it; that you can change the software and use pieces of it in new free
programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors
to deny you these rights or to ask you to surrender these rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for
a fee, you must give the recipients all the rights that we gave you. You
must make sure that they, too, receive or can get the source code. If you
link other code with the library, you must provide complete object files to
the recipients, so that they can relink them with the library after making
changes to the library and recompiling it. And you must show them these
terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library,
and (2) we offer you this license, which gives you legal permission to copy,
distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no
warranty for the free library. Also, if the library is modified by someone else
and passed on, the recipients should know that what they have is not the
original version, so that the original author’s reputation will not be affected
by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free
program. We wish to make sure that a company cannot effectively restrict
the users of a free program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained for a version
of the library must be consistent with the full freedom of use specified in
this license.
Most GNU software, including some libraries, is covered by the ordinary
GNU General Public License. This license, the GNU Lesser General Public
License, applies to certain designated libraries, and is quite different
from the ordinary General Public License. We use this license for certain
libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared
library, the combination of the two is legally speaking a combined work,
a derivative of the original library. The ordinary General Public License
therefore permits such linking only if the entire combination fits its criteria
of freedom. The Lesser General Public License permits more lax criteria
for linking other code with the library.
We call this license the “Lesser” General Public License because it does
Less to protect the user’s freedom than the ordinary General Public License.
It also provides other free software developers Less of an advantage over
competing non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries. However, the
Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage
the widest possible use of a certain library, so that it becomes a de-facto
standard. To achieve this, non-free programs must be allowed to use the
library. A more frequent case is that a free library does the same job as
widely used non-free libraries. In this case, there is little to gain by limiting
the free library to free software only, so we use the Lesser General Public
License.
In other cases, permission to use a particular library in non-free programs
enables a greater number of people to use a large body of free software.
For example, permission to use the GNU C Library in non-free programs
DRAFT - 6/25/2010
to all third parties under the terms of this License.
enables many more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
d) If a facility in the modified Library refers to a function or a table
of data to be supplied by an application program that uses the
facility, other than as an argument passed when the facility is
invoked, then you must make a good faith effort to ensure that, in
the event an application does not supply such function or table,
the facility still operates, and performs whatever part of its purpose
remains meaningful.
Although the Lesser General Public License is Less protective of the users’
freedom, it does ensure that the user of a program that is linked with the
Library has the freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution and modification
follow. Pay close attention to the difference between a “work based on the
library” and a “work that uses the library”. The former contains code derived
from the library, whereas the latter must be combined with the library in
order to run.
(For example, a function in a library to compute square roots
has a purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires that any
application-supplied function or table used by this function must
be optional: if the application does not supply it, the square root
function must still compute square roots.)
GNU LESSER GENERAL PUBLIC LICENSE
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the Library,
and can be reasonably considered independent and separate
works in themselves, then this License, and its terms, do not apply
to those sections when you distribute them as separate works. But
when you distribute the same sections as part of a whole which
is a work based on the Library, the distribution of the whole must
be on the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and every
part regardless of who wrote it.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0.
This License Agreement applies to any software library or other program
which contains a notice placed by the copyright holder or other authorized
party saying it may be distributed under the terms of this Lesser General
Public License (also called “this License”). Each licensee is addressed as
“you”.
A “library” means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
Thus, it is not the intent of this section to claim rights or contest
your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or
collective works based on the Library.
The “Library”, below, refers to any such software library or work which
has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law:
that is to say, a work containing the Library or a portion of it, either
verbatim or with modifications and/or translated straightforwardly
into another language. (Hereinafter, translation is included without
limitation in the term “modification”.)
“Source code” for a work means the preferred form of the work for
making modifications to it. For a library, complete source code means
all the source code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control compilation
and installation of the library.
In addition, mere aggregation of another work not based on the
Library with the Library (or with a work based on the Library) on
a volume of a storage or distribution medium does not bring the
other work under the scope of this License.
3.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running
a program using the Library is not restricted, and output from such a
program is covered only if its contents constitute a work based on the
Library (independent of the use of the Library in a tool for writing it).
Whether that is true depends on what the Library does and what the
program that uses the Library does.
1.
You may copy and distribute verbatim copies of the Library’s complete
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that
refer to this License and to the absence of any warranty; and distribute a
copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2.
You may modify your copy or copies of the Library or any portion of it,
thus forming a work based on the Library, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices
stating that you changed the files and the date of any change.
c)
You must cause the whole of the work to be licensed at no charge
You may opt to apply the terms of the ordinary GNU General Public
License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General
Public License has appeared, then you can specify that version instead if
you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy,
so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the
Library into a program that is not a library.
4.
You may copy and distribute the Library (or a portion or derivative of it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you accompany it with the complete
corresponding machine-readable source code, which must be distributed
under the terms of Sections 1 and 2 above on a medium customarily used
for software interchange.
If distribution of object code is made by offering access to copy from a
designated place, then offering equivalent access to copy the source
code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the
source along with the object code.
5.
A program that contains no derivative of any portion of the Library, but
is designed to work with the Library by being compiled or linked with it,
is called a “work that uses the Library”. Such a work, in isolation, is not a
derivative work of the Library, and therefore falls outside the scope of this
License.
However, linking a “work that uses the Library” with the Library creates
45
DRAFT - 6/25/2010
an executable that is a derivative of the Library (because it contains
portions of the Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section 6 states
terms for distribution of such executables.
When a “work that uses the Library” uses material from a header
file that is part of the Library, the object code for the work may be a
derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The threshold for this
to be true is not precisely defined by law.
the executable from it. However, as a special exception, the materials
to be distributed need not include anything that is normally distributed
(in either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions
of other proprietary libraries that do not normally accompany the
operating system. Such a contradiction means you cannot use both
them and the Library together in an executable that you distribute.
7.
If such an object file uses only numerical parameters, data structure
layouts and accessors, and small macros and small inline functions
(ten lines or less in length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library will still fall
under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute
the object code for the work under the terms of Section 6. Any
executables containing that work also fall under Section 6, whether or
not they are linked directly with the Library itself.
1.
As an exception to the Sections above, you may also combine or link a
“work that uses the Library” with the Library to produce a work containing
portions of the Library, and distribute that work under terms of your choice,
provided that the terms permit modification of the work for the customer’s
own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are covered by
this License. You must supply a copy of this License. If the work during
execution displays copyright notices, you must include the copyright
notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
a)
Accompany the work with the complete corresponding machinereadable source code for the Library including whatever changes
were used in the work (which must be distributed under Sections
1 and 2 above); and, if the work is an executable linked with the
Library, with the complete machine-readable “work that uses the
Library”, as object code and/or source code, so that the user
can modify the Library and then relink to produce a modified
executable containing the modified Library. (It is understood that
the user who changes the contents of definitions files in the Library
will not necessarily be able to recompile the application to use the
modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library.
A suitable mechanism is one that (1) uses at run time a copy of the
library already present on the user’s computer system, rather than
copying library functions into the executable, and (2) will operate
properly with a modified version of the library, if the user installs
one, as long as the modified version is interface-compatible with
the version that the work was made with.
c)
Accompany the work with a written offer, valid for at least three
years, to give the same user the materials specified in Subsection
6a, above, for a charge no more than the cost of performing this
distribution.
d) If distribution of the work is made by offering access to copy from
a designated place, offer equivalent access to copy the above
specified materials from the same place.
e) Verify that the user has already received a copy of these materials
or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library”
must include any data and utility programs needed for reproducing
46
You may place library facilities that are a work based on the Library sideby-side in a single library together with other library facilities not covered
by this License, and distribute such a combined library, provided that the
separate distribution of the work based on the Library and of the other
library facilities is otherwise permitted, and provided that you do these two
things:
a) Accompany the combined library with a copy of the same work
based on the Library, uncombined with any other library facilities.
This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that
part of it is a work based on the Library, and explaining where to
find the accompanying uncombined form of the same work.
8.
You may not copy, modify, sublicense, link with, or distribute the Library
except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense, link with, or distribute the Library is void, and
will automatically terminate your rights under this License. However,
parties who have received copies, or rights, from you under this License
will not have their licenses terminated so long as such parties remain in full
compliance.
9. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the
Library or its derivative works. These actions are prohibited by law if you do
not accept this License. Therefore, by modifying or distributing the Library
(or any work based on the Library), you indicate your acceptance of this
License to do so, and all its terms and conditions for copying, distributing
or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library),
the recipient automatically receives a license from the original licensor to
copy, distribute, link with or modify the Library subject to these terms and
conditions. You may not impose any further restrictions on the recipients’
exercise of the rights granted herein. You are not responsible for enforcing
compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement
or for any other reason (not limited to patent issues), conditions are imposed
on you (whether by court order, agreement or otherwise) that contradict
the conditions of this License, they do not excuse you from the conditions
of this License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as
a consequence you may not distribute the Library at all. For example, if a
patent license would not permit royalty-free redistribution of the Library
by all those who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License would be to refrain
entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply,
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any such
claims; this section has the sole purpose of protecting the integrity of
the free software distribution system which is implemented by public
license practices. Many people have made generous contributions to
the wide range of software distributed through that system in reliance
on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
DRAFT - 6/25/2010
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries
either by patents or by copyrighted interfaces, the original copyright
holder who places the Library under this License may add an explicit
geographical distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not thus excluded. In
such case, this License incorporates the limitation as if written in the body
of this License.
13. The Free Software Foundation may publish revised and/or new versions
of the Lesser General Public License from time to time. Such new versions
will be similar in spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If the Library
specifies a version number of this License which applies to it and
“any later version”, you have the option of following the terms and
conditions either of that version or of any later version published by
the Free Software Foundation. If the Library does not specify a license
version number, you may choose any version ever published by the
Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs
whose distribution conditions are incompatible with these, write to the
author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the
two goals of preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE
LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY
OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3
Schedule 4
If this Cisco product contains open source software licensed under the
OpenSSL license:
This product includes software developed by the OpenSSL Project for use
in the OpenSSL Toolkit. (http://www.openssl.org/).
This product includes cryptographic software written by Eric Young (eay@
cryptsoft.com).
This product includes software written by Tim Hudson (tjh@cryptsoft.com).
In addition, if this Cisco product contains open source software
licensed under the OpenSSL license then the license terms below in
this Schedule 3 will apply to that open source software. The license
terms below in this Schedule 3 are from the public web site at
http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of
the OpenSSL License and the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related to OpenSSL
please contact openssl-core@openssl.org.
OpenSSL License
Copyright Š 1998-2007 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1.
2.
3.
4.
5.
6.
Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
All advertising materials mentioning features or use of this software must
display the following acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)”
The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used
to endorse or promote products derived from this software without prior
written permission. For written permission, please contact openssl-core@
openssl.org.
Products derived from this software may not be called “OpenSSL” nor may
“OpenSSL” appear in their names without prior written permission of the
OpenSSL Project.
Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.
org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young (eay@
cryptsoft.com). This product includes software written by Tim Hudson (tjh@
cryptsoft.com).
47
DRAFT - 6/25/2010
3.
Original SSL License
Copyright Š 1995-1998 Eric Young (eay@cryptsoft.com)All rights reserved.
This package is an SSL implementation written by Eric Young (eay@
cryptsoft.com).
The word ‘cryptographic’ can be left out if the routines from the library
being used are not cryptographic related.
The implementation was written so as to conform with Netscape’s SSL.
This library is free for commercial and non-commercial use as long as the
following conditions are adhered to. The following conditions apply to all
code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with this distribution is
covered by the same copyright terms except that the holder is Tim Hudson
(tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright notices in the
code are not to be removed.
If this package is used in a product, Eric Young should be given attribution
as the author of the parts of the library used. This can be in the form of a
textual message at program startup or in documentation (online or textual)
provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the copyright notice, this list of
conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
All advertising materials mentioning features or use of this software must
display the following acknowledgement:
“This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com)”
4.
If you include any Windows specific code (or a derivative thereof) from the
apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson (tjh@cryptsoft.
com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The license and distribution terms for any publicly available version or
derivative of this code cannot be changed. i.e. this code cannot simply
be copied and put under another distribution license [including the GNU
Public License.]
END OF SCHEDULE 4
Americas Headquarters
Cisco Systems, Inc.
San Jose, CA
Asia Pacific Headquarters
Cisco Systems (USA) Pte. Ltd.
Singapore
Europe Headquarters
Cisco Systems International BV
Amsterdam, The Netherlands
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.
CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Stackpower, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to
the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE,
CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation,
EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,
MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase
Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
Š 2009 Cisco Systems, Inc.
Part Number 4022934 Rev A
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2010:11:08 09:28:01+08:00
Modify Date                     : 2010:11:08 09:28:25+08:00
Metadata Date                   : 2010:11:08 09:28:25+08:00
Creator Tool                    : PScript5.dll Version 5.2
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Format                          : application/pdf
Title                           : untitled
Creator                         : sandy.lin
Document ID                     : uuid:e03c8381-ab88-a546-85c6-67d1f94a4b3c
Instance ID                     : uuid:e1005123-6615-4fd2-ab9e-5875cafe5336
Page Count                      : 55
Author                          : sandy.lin
EXIF Metadata provided by EXIF.tools
FCC ID Filing: LDK-RMN302

Navigation menu