Citizen Systems Japan D06B1 Printer with RFID Transmitter User Manual

D

Di

ig

gi

it

ta

al

l

P

Ph

ho

ot

to

o

P

Pr

ri

in

nt

te

er

r

Users Manual

DS40

DS80

Version 0.03

1

●Concerning Copyright

The copyrights for this document are the property of CITIZEN SYSTEMS JAPAN

CO.,LTD. Reproduction of any or all of the contents of this document without consent of the

company is a violation of copyright law. However, one back-up copy may be made fo

r

non-commercial, personal purposes.

Also, the contents of this document are subject to change in the future without prior notice.

●Concerning Safety Warnings

Warnings concerning safety and use, and the contents of this document, conform to existing

standards as of the date published.

●Concerning Modification

This printer was planned, developed, and manufactured by CITIZEN SYSTEMS JAPAN

CO., LTD, and for safety purposes, any modification of the device is prohibited.

2

Introduction

Thank you for purchasing this device.

This document explains the handling and operation required to use this printer.

Please read this document well before use.

Be sure to read “For Safe Operation” (Pg 2-4), and operate the printer correctly.

For Safe Operation

・ Be sure to read this document before use. After reading, keep it in a safe place, where it can be re-read as

needed.

・ The warnings listed here are to ensure proper use of the device, to prevent physical injury to the customer or

other persons, and to prevent property damage. Please obey these warnings.

■ About “Warning” and “Caution”

Listed below, the possible levels of injury or damage due to misuse are categorized as “Warning” and

“Caution”, according to the degrees of danger involved.

■About the symbols

The symbols shown have the following meanings:

A

ccidents caused by failure to heed the warnings accompanying this symbol could

lead to serious or fatal injury.

Warning

A

ccidents caused by failure to heed the warnings accompanying this symbol could

lead to physical injury or property damage.

Caution

This symbol calls attention to contents of warnings and cautions.

Details are indicated in or near this s

y

mbol.

This symbol indicates prohibited actions.

The

p

rohibited actions are detailed within the s

y

mbol.

This symbol designates necessary actions, and relevant content.

Details of the actions are shown within the symbol.

3

WARNING

・ Use only with the designated voltage and frequency. Improper connection could cause

electric shock or fire.

・ Avoid overstressing outlets and using extension cords. The outlet could overheat and

cause a fire.

・ Do not damage, destroy, bundle, or alter the power cord. Also, placing heavy objects on,

pulling on, or bending the cord excessively can damage it, and could cause a fire.

・ Do not set the printer up in places with salinity or corrosive gases in the air. This coul

d

cause a fire.

・ Do not block the vents. Heat could build up in the printer and cause a malfunction or

fire.

・ Do not stand on or place heavy objects on the printer. Also, do not use excessive force

on the buttons, switches, terminals, etc. This could break the printer and cause injury to

the user or others.

・ Store the bag for the printer out of the reach of children. It could cause suffocation if

placed over the head.

・ Be careful to avoid injury or damages from the edges in the printer.

・ Do not use this printer for applications where malfunction could be life-threatening (such

as medical, space, aeronautic, or other applications that require extreme reliability).

・ The printer weighs approximately 14 kg (31 lbs). When moving it, lift in a way that

avoids excessive physical stress. Lifting recklessly or dropping the printer could cause

injury.

・ Locate the printer as close to an outlet as possible, and allow easy access to unplug the

power cord in case of problems.

・ If there is dust on the plug, clean it off thoroughly. It could cause electric shock or a

short-out.

・ If metal objects or liquids have fallen into the printer, and there is smoke, a strange odor,

or any other apparent abnormality, immediately turn the power OFF, and unplug the

power cord. Then contact a service representative. Do not continue using the printer if

it is not operating properly. This could cause shock, short circuit, or fire.

・ Be sure to attach the ground. Otherwise, it could short-circuit, causing electric shock or

fire.

・ Do not plug or unplug the cord with wet hands. This could cause electric shock.

・ Do not open the inside of the printer, disassemble internal parts, or modify the printer. I

t

could cause electric shock, fire, or injury, or break the printer. For internal check-ups,

adjustments, or repair, please contact a service representative.

4

CAUTION

・ Do not set the

p

rinter up in dusty or overly humid places. This could cause fire or electric shock, or

damage the printer.

・ Do not set the printer up on an unstable surface. It could fall and cause injury to the user or others.

・ Do not allow foreign objects to enter the printer. They could cause electric shock, short circuit, o

r

fire, or break the printer. If something falls into the printer, immediately turn the power OFF, an

d

call a service representative.

・ Do not open the cover while printing. This could break the printer.

・ Do not spill or spray liquids or chemicals into the printer.

・ When cleaning the cover, do not use thinner, trichloroethane, benzene, ketone-

b

ased cleaners, o

r

chemically treated cloths. They could discolor or deteriorate the cover.

・ At least once a year, unplug the power cord, and clean the prongs and the plug. If dust accumulates,

it could cause a fire.

・ When printing continuously for long periods of time in a small room, be sure to ventilate properly.

・ If use is intended on a transportation vehicle (train, truck, ship, etc.), please talk to a representative in

advance.

・ When disposing of the printer, peripheral items, packaging, or media, please abide by local waste

removal ordinances. For details, contact your local government offices.

・ When unplugging the cord, grip the plug. Do not pull on the cord. It could damage the cord, an

d

cause electric shock or fire.

・ When moving the printer, be sure to unplug the power cord. Otherwise, the cord may be damaged,

which could cause fire or electric shock.

・ When not using the printer for extended periods of time, for the sake of safety, be sure to unplug the

power cord. It could cause electric shock or fire.

・ Parts with this warning get extremely hot. Do not touch after printing. There is a danger of burns.

・ Do not touch the gear mechanisms. There is a danger of injury if fingers get caught in the spinning

gears.

5

Cautions for Set-up

・ Prior to operation, read “For Safe Operation” carefully and observe the rules therein.

・ Use care when moving the printer. Never try carrying the printer alone.

Dropping it could cause injury or damage to other property.

・ Do not use or store the printer near fire, excessive moisture, in direct sunlight, near an air

conditioner or heater, or any other source of unusually high or low temperature or humidity, or

excessive dust.

・ Do not place the printer where chemical reactions occur, such as in a laboratory.

・ Do not set up the printer where there is salinity or corrosive gas in the air.

・ The printer must sit on a firm, level surface where there is ample ventilation.

・ Do not put anything on the top of the printer.

・ Do not place the printer near a radio or television, and do not use the same wall outlet for the

printer and radio or television. Radio or television reception could be adversely affected.

・ Do not use a power voltage or frequency other than those specified.

・ Do not put anything on the power cord or step on it.

・ Do not drag or carry the printer by the power cord or USB cable.

・ Avoid plugging the power cord into an outlet with many loads.

・ Do not bundle the power cord.

・ Always grip the plug housing, not the cord, to plug/unplug the power cord.

・ Make certain the power is turned off before connecting/disconnecting the USB cable.

・ Avoid lengthening the signal cable or connecting it to any noise-producing device.

If it is unavoidable, use a shielded cable or twisted pair for each signal.

・ Place the printer near the outlet where the power cord can be unplugged easily to shut off

power.

・ Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be danger of electric

shock.

・ Use the appropriate specified cord set.

Only use items that are certified safe according to the standards of the country where they are to

be used