Clarke Cav 26 Users Manual 71114A.pmd
vacuum26galloncav26 2d4fa5dc-02c4-49b4-b05d-08733b28ff4d Clarke Vacuum Cleaner CAV 26 User Guide |
2015-02-05
: Clarke Clarke-Cav-26-Users-Manual-531140 clarke-cav-26-users-manual-531140 clarke pdf
Open the PDF directly: View PDF .
Page Count: 20
Download | |
Open PDF In Browser | View PDF |
Vacuum 26 Gallon Operator's Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: Clarke® , 2100 Highway 265, Springdale, Arkansas 72764 Form No. 71114A 6/06 Printed in the U.S.A. Table of Contents Important Safety Instructions .................................................................................... 3 Specifications ......................................................................................................... 4 Introduction and Instructions ..................................................................................... 4 Operating Instructions .............................................................................................. 6 Troubleshooting ....................................................................................................... 8 Section II Parts and Service Manual Frame Assembly Drawing ....................................................................................... 10 Frame Assembly Parts List ..................................................................................... 11 Container Unit Assembly Drawing ........................................................................... 12 Container Unit Assembly Parts List ......................................................................... 13 Suction Unit Assembly Drawing ............................................................................... 14 Suction Unit Assembly Parts List ............................................................................. 15 Filter Group Assembly Drawing and Parts List ......................................................... 16 Control Panel Assembly Drawing and Parts List ...................................................... 17 Electrical Schematic ............................................................................................... 18 Page -2- Clarke® American Sanders Operator's Manual - CAV 26 IMPORTANT SAFETY INSTRUCTIONS DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Operator's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Operator's Manual and on your machine. CAUTION: Failure to read and observe all CAUTION statements could result in damage to the machine or to other property. Read and observe all CAUTION statements found in your Operator's Manual and on your machine. READ ALL INSTRUCTIONS BEFORE USE WARNING: To reduce the risk of fire, electric shock, or injury: - Use only as described in this manual. Use only manufacturers recommended attachments. For indoor dry pick-up only. Do not expose to rain or weather. If machine is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a service center. Turn off all controls before unplugging Do not handle plug or machine with wet hands. Do not use with damaged plug or cord. Do not unplug by pulling on cord. To unplug, grasp the plug not the cord. Do not pull or carry by cord, use cord as a handle, close a door on the cord, or pull cord around sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not leave machine when plugged in. Unplug from outlet when not in use or before servicing. Do not put any objects into openings. Do not use with any openings blocked. Keep free of dust, lint, hair, and anything that may reduce airflow. Keep hair, loose clothing, fingers, and body parts away from openings and moving parts. Do not use to pick-up flammable or combustible liquids, such as gasoline or solvents. Do not use where they may be present. Do not use to pick-up hot, smoldering, or burning substances. Do not use where explosive vapors, such as gas, solvents, alcohol, fuels, or combustible materials such as grain, wood dust, are present in the air. Keep the work area well ventilated. Dust produced from sanding wood or varnish could self ignite causing injury or damage. If this material has been picked up, empty it immediately after use in a metal container. Do not use to pick-up health endangering dust. Do not use unless machine is fully assembled. Do not modify the machine. Read all instructional labels on the machine. Replace damaged labels. Do not allow to be used as a toy. Close attention is necessary when used around children. Use extra care when cleaning on stairs. Connect to properly grounded outlet. See “grounding Instructions”. Do not use unless all filtering elements are present. Clean filtering elements frequently. SAVE THESE INSTRUCTIONS. Clarke® American Sanders Operator's Manual - CAV 26 Page -3- SPECIFICATIONS Model Voltage CAV 26 120 V Frequency Power 60 Hz 2400 W (800 x 3) Ambient Temp Volume Flow (CFM) -23°F to 86° F 290 (max) Static Lift (inches H2O) Sound Level dB(A) 82 73 Cord Length (ft.) Tank Volume 36 26 gal. Width (in.) Depth (in.) 26 27 Height (in.) Weight (lbs.) 61 143 INTRODUCTION AND INSTRUCTIONS The CAV 26 comes fully assembled. It is specifically designed for dry pick-up of fine dust made from grindings of wood or gypsum. It is mounted on tough rubber wheels, two of which swivel in order to make the machine easy to handle. It also has brakes to safely stop the machine in place. NOTE: When performance has declined noticeably, empty tank and clean the filters accordingly. 4 1 2 3 3 1 1 Figure 1 Page -4- Figure 2 2 2 Figure 3 Clarke® American Sanders Operator's Manual - CAV 26 INTRODUCTION AND INSTRUCTIONS, cont. Features Figure 1, 1 - Control Panel For explanation of controls, see "Controls" section this page. Figure 1, 2 - Inlet This inlet is for installation of vacuum hose and accessories. Figure 1, 3 and Figure 2, 1 - Debris Canister The debris canister should be emptied when the canister is full. To empty canister, lift debris canister lever (figure 3,2). Debris canister will lower until it rests with it's wheels on the floor. Grip the handle and remove the canister, then empty it's contents. To fit the canister back in place, set it under the vacuum, making sure the full sight level gauge (figure 3,1) remains visible from the outside. Then push lever (figure 3,2) downwards, allowing the canister to lift until it fits against filtering chamber. Figure 1, 4 - Filter Cleaning Lever This lever is to used to clean the filter. When manometer (figure 4, 1) reads that the filter is clogged, turn the filter cleaning lever several times with force in order to shake the dust from the filter. Do not operate lever with vacuum running. Wait a few minutes for the dust to settle at the bottom of the container, then empty. Figure 3, 1 - Full Sight Level Gauge This gauge indicates the debris level in the debris canister (figure 1,3). The debris canister should be emptied when it is full. Before emptying debris canister, switch off the machine by pressing the vacuum motor switches (figure 4,2) and remove plug from the power supply. Figure 3, 2 - Debris Canister Lever Lift this lever so that debris canister can be removed and emptied. Make sure to lower the lever when you replace the debris canister. Figure 3, 3 - Balancing Hose Balances vacuum around polytank liner (fig 2,2), so it's not sucked into the filter. Controls Figure 4, 1 - Manometer to display filter loading The vacuum in the filter increases proportionally as the filter clogs. Then the manometer needle will move from green (filter good) to the red (filter clogged) section. 3 4 Figure 4, 2 - Vacuum Motor Switches This model is fitted with 3 motors, so it has three vacuum motor switches on the control panel. Press the switches to start the vacuum motors. The warning lights (green lights) will come on. Press the switches again to stop the motors. The warning light will go out. Figure 4, 3 - Electrical Label 1 Figure 4, 4 - Illuminated Mains Voltage Indicator When on, this indicates that the vacuum is connected to the electrical supply. 2 Figure 4 Clarke® American Sanders Operator's Manual - CAV 26 Page -5- OPERATING INSTRUCTIONS To operate this machine follow these procedures: 1. Position the CAV 26 in a convenient location near a wall outlet and within reach of the working area. If the surface is not level, set the brakes on the casters. CAUTION: Do not use an extension cord with the CAV 26 or you will experience a loss in performance. Should an extension cord be necessary, use one sized 12 AWG and no longer than 50' in length. An extension cord sized smaller than 12 AWG or greater than 50' in length will overheat and potentially cause a fire. Figure 5 2. Connect the CAV 26 to a wall outlet matching one of the two shown in figure 5. No adaptor should be used with this appliance. WARNING: This appliance must be grounded. Should an electrical malfunction occur, the grounding conductors provide a path to harmful current. Do not connect this appliance to any other wall outlet than one of those shown in figure 5. Consult an electrician if there is reason to doubt that the wall outlet is not wired correctly. Do not remove the grounding pin on the power cord. Do not use this appliance with a damaged power cord or plug. 3. The CAV 26 uses three individually activated vacuum motors that allow tailoring the delivery for the available electrical supply and application. Figure 6 For Light Duty Applications: Activate one of the three vacuums. To activate a vacuum motor, push one of the three vacuum motor switches (see figure 6). To deactivate the vacuum motor, push the vacuum switch a second time. For Heavy Duty Applications or Multiple Simultaneous Users: Activate two of the vacuum motors if you are connected to a 15A wall outlet. You may activate all three vacuum motors if you are connected to a 20A wall outlet. WARNING: Do not activate all three vacuum motors if you are connected to a 15A wall outlet or you will overload the circuit. An overloaded circuit will overheat and potentially cause a fire. Always deactivate the vacuum motor(s) before disconnecting the power cord. Page -6- Clarke® American Sanders Operator's Manual - CAV 26 OPERATING INSTRUCTIONS 3 4. Install a poly-liner (fig. 7, 1) in the debris canister (fig. 7, 2). To release the debris canister raise the lever (fig. 7, 3) as shown.. The poly-liner provides quick convenient disposal. 5. When the debris canister becomes full, the manometer (fig. 8, 1) reads in the red, deactivating all vacuum motors. 6. Allow time for the dust to settle, then operate the filter cleaning lever (fig. 9, 1) several times. 7. Remove the poly-liner and replace with a new liner. 8. Replace the debris canister. To fit the canister back in place, set it under the vacuum and push the lever downwards. This allows the canister to lift until it fits against the filtering chamber. 2 1 Figure 7 1 Figure 8 1 Figure 9 Clarke® American Sanders Operator's Manual - CAV 26 Page -7- TROUBLESHOOTING Problem The vacuum fails to start Cause Action 1. Check whether power is reaching the socket. 1. No power. Check whether the plug and cable are in good condition. Ask for assistance from an authorized service technician. The rpm rate of the vacuum increases. 1. Clogged primary filter. 1. Shake the filter. Replace it if this is not sufficient. 2. Suction hose clogged. 2. Check the suction hose / wand and clean it. 1. The filter is torn. 1. Replace it with another with identical characteristics. 2. Inadequate filter. 2. Replace it with another with suitable characteristics. Noisy vacuum motors 1. Worn or broken carbon brushes. 1. Remove and replace the carbon brushes. Electrostatic current on the vacuum. 1. Nonexistent or ineffective grounding. 1. Check all ground connections. Especially check the suction inlet fitting. Dust leaks from the machine. Lastly, the hose must be strictly antistatic. Page -8- Clarke® American Sanders Operator's Manual - CAV 26 Section II Parts and Service (71114A) Clarke® American Sanders Operator's Manual - CAV 26 Page -9- Frame Assembly Drawing 2/06 Page -10- Clarke® American Sanders Operator's Manual - CAV 26 Frame Assembly Parts List 5/06 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Part No. 8 14087 8 14084 8 14262 8 38033 8 38034 8 14266 8 14267 8 14256 8 14261 8 14259 8 14258 8 18513 8 18506 8 40392 8 16060 8 40582 8 36196 8 40035 8 40581 229102 80312A 229102 80312A 58050A 83002A 98456A 229102 80163A 80314A 229102 80163A 920936 980648 80315A 229044 80162A 8 38038 8 16380 8 40396 8 40407 8 16177 80163A 229102 964058 80163A 980205 1803337 229102 Description Pin Pin Pin Washer Washer Washer Spring Lever Pin Bushing Lever Handgrip Pillar Collar Basket Caster, Cart Cart Plug Wheel, Cart Washer, Ø 8 Nut, M8 Block Washer, Ø 8 Nut, M8 Block Screw, M8 x 65 Soc. Rivet, Ø 6,4 x 15 Screw, M8 x 50 Washer, Ø 8 Nut, M8 Screw, M8 x 65 Washer, Ø 8 Nut, M8 Nut, M12 Washer, Ø 12 Screw, M10 x 65 Washer, Ø 10 Nut, M10 Rivet Side-Piece Plug Push Rod Cable Support Nut, M8 Washer, Ø 8 Screw, M8 x 16 Nut, M8 Washer, Ø 8 x 24 Screw, M8 x 25 Washer, Ø 8 Clarke® American Sanders Operator's Manual - CAV 26 Qty 2 2 2 2 2 2 2 2 2 2 1 2 2 1 1 2 1 2 2 2 2 2 2 2 9 4 4 4 4 4 4 2 2 2 2 2 6 2 2 2 1 4 6 6 4 2 2 4 Page -11- Container Unit Assembly Drawing 2/06 Page -12- Clarke® American Sanders Operator's Manual - CAV 26 Container Unit Assembly Parts List 3/06 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 38 Part No. Ref. Ref. Ref. 8 36028 5 60133 Ref. Ref. 8 17007 8 12013 8 17006 Ref. Ref. Ref. 924004 58413A 58411A 58414A Ref. 80312A 424033 964058 80214A 8 40881 8 40187 830331CS 8 40771 8 17021 8 40001 964058 229102 920936 87101A 980648 8 31221 722001 7 22064 Description Container Bracket Plaque Latch Hose, Balancing Label Label Seal, Inlet Deflector Seal, Container Filler Spring Pin, Ø 3 x 16 Nut, M5 Screw, M5 x 20 Screw, M5 x 25 Screw, M5 x 30 Push Button Nut, M8 Block Washer, Ø 8 x 32 Screw, M8 x 16 Screw, M6 x 12 Reducer, M6 x 8 Ring Nut Debris Canister Asm (Includes 23-33) Handle Bumper Wheel Screw, M8 x 16 Washer, Ø 8 Nut, M12 Washer, Ø 12 Washer, Ø 12 Grid Inlet Fitting Inlet Splitter Qty 1 2 2 2 1 1 1 1 1 1 2 2 4 1 2 1 1 4 4 4 4 2 2 1 2 4 4 4 4 4 4 4 1 1 1 Ref. Items 1 - 24 = Part No. 8 31687CS, Complete Container, Qty. 1 Ref. Items 11, 12, 13, 18 = Part No. 8 32178, Complete Inlet Asm., Qty. 1 Clarke® American Sanders Operator's Manual - CAV 26 Page -13- Suction Unit Assembly Parts List 2/06 Page -14- Clarke® American Sanders Operator's Manual - CAV 26 Suction Unit Assembly Parts List 6/06 Ref. 1-6 8 9 10 11 12 NI 13 14 16 17 18 19 20 21 23 24 25 26 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Part No. 8 17324 8 14270 8 12168 8 13162 8 17325 8 54006 839067.115 8 16179 8 17326 8 16243 816381CFM 8 40401 Ref. 8 38036 8 40404 8 14271 8 35049 980646 88208A 88208A 56446A 88208A Ref. Ref. 80162A 8 14052 8 39594 80065A 920934 8 14499 8 14509 8 38036 80214A 980646 980679 8 16257 8 14052 8 40583 229102 80312A 8 33254 8 38048 80313A Description Soundproofing Kit Spacer Valve Valve Seat Seal Vacuum Motor Carbon Brush for ref. 12 (2 reqd.) Motor Locator Seal Housing, Vacuum Motor Cover Hosebarb Tube Rivet M6 T-Fitting Spacer Motor Platform Washer, Ø 6 Screw, M6 x 10 Screw, M6 x 10 Screw, 4.8 x 19 Screw, M6 x 10 Label Label Nut, M10 Nut Cable Gland Screw, M4 x 8 Nut, M4 Spacer Spacer Rivet, M6 Screw, M6 x 12 Washer, Ø 6 x 18 Washer, Ø 18 Cover Nut Lever Washer, Ø 8 Nut, M8 "Block" Cage Ring Dowel M6 x 10 Qty 1 2 3 3 6 3 ea. 1 3 1 1 1 0.4m 4 1 1 1 4 2 2 6 4 1 1 1 1 1 1 1 1 1 3 3 3 4 1 1 1 1 1 1 1 2 NOTE: indicates a change has been made since the last publication of this manual. Clarke® American Sanders Operator's Manual - CAV 26 Page -15- Filter Group Assembly Drawing & Parts List 3/06 Ref. 1 2 3 4 5 6 Part No. 8 17026 Ref. Ref. Ref. Ref. 8 17749 Description Seal Tie Ring Tie Filter Filter Liner, Polyester Qty 1 6 1 1 1 1 Ref. Items 1 - 5 = Part No. 8 33151, Complete Filter, Qty 1 Page -16- Clarke® American Sanders Operator's Manual - CAV 26 Control Panel Assembly Drawing & Parts List 6/06 Ref. 1 2 3 4 5 6 7 8 9 10 12 13 15 17 18 19 20 21 22 23 24 25 26 29 30 31 Part No. 8 39531 Ref. Ref. 80065A Ref. 8 39533 8 40403 Ref. Ref. Ref. 8 39526 8 40400 8 39525 8 39529 Ref. 80058A 80058A 920934 924004 980982 980982 924004 58411A Ref. Ref. 8 391160 Description Switch Cover Connection Block Label Screw, 4 x 10 Cables Kit Suppressor Pressure Switch Panel Seal Decal Voltage Indicator Manometer Switch Cable Locking Device Screw, 3.9 x 9.5 Washer, Ø 4 Washer, Ø 4 Nut, M4 Nut, M5 Washer, Ø 5 Washer, Ø 5 Nut, M5 Screw, M5 x 25 Screw, 3.9 x 9.5 Screw, 3.9 x 16 Cable Qty 3 1 3 1 1 1 1 1 1 1 1 1 3 1 2 2 1 1 2 1 1 1 1 2 2 1 Ref items 1-29 = Part No. 8 41098, Complete Panel Asm., Qty 1 Clarke® American Sanders Operator's Manual - CAV 26 Page -17- Electrical Schematic 6/06 (Optional) (Optional) Page -18- Clarke® American Sanders Operator's Manual - CAV 26 CLARKE PRODUCT SUPPORT BRANCHES U. S. A. Locations CORPO PRODUCTION FACILITIES Clarke® , Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (479) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 American Lincoln®, Bowling Green, Ohio 43402 1100 Haskins Road European Locations PRODUCTION FACILITIES ALTO Danmark A/S, Aalborg Blytaekkervej 2 DK-9000 Aalborg +45 72 18 21 00 ALTO Danmark A/S, Hadsund Industrikvarteret DK-9560 Hadsund +45 72 18 21 00 SALES SUBSIDIARIES SERVICE FACILITIES Clarke®, Elk Grove, Illinois 60007 2280 Elmhurst Road (847) 956-7900 ALTO US - Canada, Ontario (Canada) 4080 B Sladeview Crescent Unit 1 Mississauga, Ontario L5L 5Y5 (905) 569 0266 Clarke®, Denver, Colorado 80204 1955 West 13th Ave. (303) 623-4367 ALTO Overseas Inc., Sydney (Australia) 1B/8 Resolution Drive Caringbah NSW 2229 +61 2 9524 6122 Clarke®, Houston, Texas 77040 7215 North Gessner Road 713-937-7717 ALTO Cleaning Systems Asia Pte Ltd., Singapore No. 17 Link Road Singapore 619034 +65 268 1006 SERVICE AND SALES FACILITY ALTO Deutschland GmbH, Bellenberg (Germany) Guido-Oberdorfer-Straße 2-8 89287 Bellenberg +49 0180 5 37 37 37 American Lincoln® / Clarke, Madison Heights, Michigan 48071-0158 29815 John R. (810) 544-6300 American Lincoln® / Clarke, Marietta, Georgia 30066 1455 Canton Road (770) 973-5225 ALTO Cleaning Systems (UK) Ltd., Penrith Gilwilly Industrial Estate Penrith Cumbria CA11 9BN +44 1768 868 995 ALTO France S.A. Strasbourg B.P. 44, 4 Place d’Ostwald F-67036 Strasbourg Cedex 2 +33 3 8828 8400 Clarke® Clarke American Sanders A.L. Cook Customer Service Headquarters and Factory 2100 Highway 265 Springdale, Arkansas 72764 (479) 750-1000 Technical Service 1-800-356-7274 Clarke® American Sanders Operator's Manual - CAV 26 ALTO Nederland B.V. Postbus 65 3370 AB Hardinxveld-Giessendam The Netherlands +31 184 677 200 ALTO Sverige AB, Molndal (Sweden) Aminogatan 18 Box 4029 S-431 04 Molndal +46 31 706 73 00 ALTO Norge A/S, Oslo (Norway) Bjornerudveien 24 N-1266 +47 2275 1770 Page -19- Clarke® American Sanders U. S. Warranty This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of two years from the date of purchase, when operated and maintained in accordance with Clarke American Sanders's Maintenance and Operations instructions. This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable, rubber parts, hoses and motor brushes. If difficulty develops with the product, you should: (a). Contact the nearest authorized Clarke American Sanders repair location or contact the Clarke American Sanders Service Operations Department, 2100 Highway 265, springdale, Arkansas, for the nearest authorized Clarke American Sanders repair location. Only these locations are authorized to make repairs to the product under this warranty. (b). Return the product to the nearest Clarke American Sanders repair location. Transportation charges to and from the repair location must be prepaid by the purchaser. (c). Clarke American Sanders will repair the product and or replace any defective parts without charge within a reasonable time after receipt of the product. Clarke American Sanders's liability under this warranty is limited to repair of the product and/or replacement of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUENTIAL DAMAGES. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY, SHALL BE IMPLIED. A warranty registration card is provided with your Clarke American Sanders product. Return the card to assist Clarke American Sanders in providing the performance you expect from your new floor machine. Clarke, 2100 Highway 265, Springdale, Arkansas 72764. Clarke American Sanders reserves the right to make changes or improvements to its machine without notice. Always use genuine Clarke American Sanders Parts for repair. 2100 Highway 265 Springdale, Arkansas, 72764 Page -20- Clarke® American Sanders Operator's Manual - CAV 26
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Mode : UseThumbs XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PageMaker 7.0 Modify Date : 2006:07:08 10:57:52-05:00 Create Date : 2006:07:08 10:37-05:00 Metadata Date : 2006:07:08 10:57:52-05:00 Format : application/pdf Title : 71114A.pmd Creator : howkril Document ID : uuid:4a9a5acd-a666-4bd6-a0e5-90fb3c8d1d74 Instance ID : uuid:6fa3fc54-e786-4e7f-bff6-109fb350f1a0 Page Count : 20 Page Layout : SinglePage Author : howkrilEXIF Metadata provided by EXIF.tools