Climax Technology Co WT User Manual 40132

Climax Technology Co Ltd 40132

8

Download: Climax Technology Co WT User Manual 40132
Mirror Download [FCC.gov]Climax Technology Co WT User Manual 40132
Document ID40132
Application IDDmps647WafEl8MgxGL8tiQ==
Document Description8
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize6.23kB (77820 bits)
Date Submitted1999-06-03 00:00:00
Date Available1999-04-06 00:00:00
Creation Date2001-06-19 12:10:59
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-06-19 12:11:04
Document Title40132.pdf
Document Author: VicodinES /CB /TNN

ETC ReparlNu ETXSR-OI-{MS FCC 1D ‘ GXQWT
Exhibit E............... User’s Manual
m Nnvfl
Wrist Transmitter
0 Features
0 Tamper Proof -— Any attempt to tamper with the Wrist Transmitter after
installation will stop the operation of the Transmitter and Will be detected by the Base Unit immediately.
0 Water proof
0 Lightweight (0902 only)
0 Code Hopping encryption avoids any possrbility of code duplication.
0 Easy range check.
0 Superior radio transmission range
0 Low power consumption — long battery life
0 Low battery detection
0 Adjustable belt length
0 Options of various transmission periods are available
0 Identifying the parts.
fl Conductive Belt
0 One end of the Conductive Belt is fixed
on the main body of the Wrist
Transmitter by the factory,
O The other end of the Conductive Belt is
to be inserted into the slit on the other
side of the main body.
0 Only after the belt is inserted into the
slit and fastened with the two
Fastening Pins, then the Wrist
Transmitter can function properly.
AZJ Test Button
0 During Learning, press the Test Button, the Wrist Transmitter will send the ”Learning
code" for the Base Unit to learn the lD code of the Wrist Transmitter.
0 After installation, press Test Button, a test Signal will be send. If the Base Unit
receives the test signal, it will sound beeps.
3] Fastening Pin
0 The two pins is used to fasten the belt in its position.
Preparing the Wrist Transmitter
Before installing the Wrist Transmitter on the subject, the D code of the Wrist Transmitter should be learned by
the Base Unit so that the Wrist Transmitter can communicate with the Base Unit.
Step 1. Insert the Learning Tool into the right side of the slit until it touch the contact
inside the slit.
Step 2. Softly push the tool forward and hold it.
Step 3, Press the Test Button on the top of the Wrist Transmitter The Wrist Transmitter
will send the ”Learning Code".
Step 4. If the Base Unit successfully receives the Learning Code, it will sound a short
beep.
Step 5. Release the button.
Step 6, Remove the tool and the Learning is completed.
0 Installing the Wrist Transmitter
After the lD Code of a Wrist Transmitter is learned by the Base Unit, the Wrist Transmitter is paired with the Base
Unit and is ready for installation,
Step 1. Find a suitable length for the subject and locate the v-cut line near-by on the
belt.
Step 2. Trim the belt along the v-cut line.
Step 3, Wear the Wrist Transmitter on the subject and insert the belt into the slit softly
until it touch the contact, two of the positioning holes on the belt should be
aligned with the two screw holes on the body
Step 4. Completely insert the 2 Fastening Pins into the screw holes.
Step 5. Installation is completed, It the Base Unit is also installed, you can test the
Wrist Transmitter by pressing the Test Button on the top of the Wrist
Transmitter to confirm trouble—tree radio communication between the Wrist
Transmitter and Base Unit, The Base Unit should sound a short beep every
time the button is pressed.
@ Once the Fastening Pins are inserted, it is not possible to take them off Without
damage the Write Transmitter
? Once the installation is completed, if the belt is cut, the Wrist Transmitter will
stop operation and will never be functional again.
@= It is recommended that before inserting the Fastening Pins, try to hold the belt
in its position by any means, then do the radio communication test to confirm
the signal range can cover the entire premises and everything is all right.
@ After the installation is completed, the Wrist Transmitter start sending signals
once every two minutes until the battery is flat
0 Battery Life & Low Battery Detection
63 Battery Life & Low Battery Detection
G The Wrist Transmitter uses one 3V SOOmAh lithium battery and will last for at least 12
months.
0 If the battery voltage is less than 2.7\/, the Wrist Transmitter will send "Low Battery”
signaI to the Base Unit. The Base Unit will then notify the Monitoring Station the
Transmitter‘s battery is low and needs replacement,
0 FCC Notice
Mode11WT-2
FCC IDrGX9WT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES, OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (I) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:19 12:10:59
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : VicodinES /CB /TNN
Title                           : 40132.pdf
Modify Date                     : 2001:06:19 12:11:04-04:00
Page Count                      : 5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: GX9WT

Navigation menu