Cobra Electronics 2016C RADAR DETECTOR User Manual

Cobra Electronics Corporation RADAR DETECTOR Users Manual

Users Manual

Nothing Comes Close to a Cobra®A1The Cobra line of quality products includes:For more information or to order any of our products, please visit our website:www.cobra.com©2016 Cobra Electronics Corporation6500 West Cortland StreetChicago, Illinois 60707 USAwww.cobra.comEnglishNothing Comes Close to a Cobra®Important InformationCustomer AssistanceFederal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement ofcials until and unless they are prohibited from doing so by federal court action.Safe Driving Motorists, as well as operators of emergency or service vehicles, are expected to exercise all due caution while using this product, and to obey all applicable trafc laws. Do not attempt to change settings of the unit while in motion.Security of Your Vehicle Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft.IntroductionPrinted in the PhilippinesPart No. 480-1071-PVersion BOperating Instructions RADAR/LASER PROTECTIONRAD450Important Information and Customer Assistance CB RadiosDash CamsRadar DetectorsMarine VHF RadiosPower InvertersAccessoriesRAD450_MANL_vB.indd 1-1 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®Nothing Comes Close to a Cobra®EnglishA2 A3 20Display and Product Features NOTESControls Indicators and ConnectionsCongratulations! You’ve made a smart choice by purchasing a radar/laser detector from Cobra. Just look at some of the sophisticated features and capabilities your new unit includes:Radar/Laser Protection Detects all radar and laser guns.LaserEye Detects laser signals from both front and rear.VoiceAlert Digital voice announcements keep your eyes on the road.QuietDrive™ Quiet Drive is a muted driving mode for times when a driver wants less audible feedback while talking with passengers, on the phone, etc.Premium Anti-Falsing Circuitry Automatically reduces false alerts from erroneous sources including vehicle collision avoidance systems, trafc ow monitoring devices and other radar detectors.Controls, Indicators and Connections •Easy-to-Read Display •Product Features •12V DC Power JackDim ButtonFor adjusting the display brightness.Mute ButtonFor manual mute of audio alerts, changing standby screens, turning Quiet Drive on/off.On-Off/Volume ControlAllows you to adjust thevolume of the alerts.Introduction IntroductionLaserEyeFor detection oflaser signals.SpeakerThis booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.SEN ButtonAdjust sensitivity and ltering modes to reduce unwanted alerts.FCC NOTICE This device complies with part 15 of FCC rules: Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.Intro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsWindshield Bracket MountAVIS FCC Cet appareil est conforme à la partie 15 des règles de la FCC: Son fonctionnement est soumis aux deux conditions suivantes: (1) Ce dispositif ne peut causer des interférences nuisibles, et (2) Cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement.Menu ButtonTo select detector settings.Radar Band FrequencyUSBPortSignal StrengthRadar/Laser Protection Detects all radar and laser guns.LaserEye® Detects laser signals from both front and rear.VoiceAlert Digital voice announcements help keep your eyes on the road. QuietDriveTM Muted driving mode for times driver wants less audible feedback while talking with passengers or on the phone.Premium Anti-Falsing Circuitry Automatically reduces false alerts from erroneous sources including automatic door openers, xed position trafc ow monitoring systems and other radar detectors. Updatable IVT FilterTM User updatable system automatically reduces false alerts from moving In-Vehicle Technology sources such as collision avoidance systems and adaptive cruise control.Sensitivity Modes Selectable Low/Med/High modes reduce falsing in densely populated areas.Auto Mute Automatically mutes audio for sustained alerts.Eye-Catching OLED Display Bright white OLED display features band identication icons and numeric signal strength meter.Adjustable Sensitivity Select preferred radar sensitivity (City/City Max/Highway) to suit driving environment.Dual Language English and Spanish voice and text alerts.6’ Power Cord and Mount Included.RAD450_MANL_vB.indd 2-21 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®1ContentsIntroductionImportant Information ................................. A1Controls, Indicators and Connections ..................... A2Display ............................................. A3Product Features .................................... A3Your DetectorInstallation ........................................... 2Getting Started ....................................... 5Buttons ............................................. 5 SEN .............................................. 5 Anti-Falsing Circuitry .................................5 MUTE ............................................. 6 Quiet Drive ........................................ 6 Battery Voltage ..................................... 6 DIM .............................................. 6Menu-User Settings .................................... 6Menu-Alert Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Detail ............................................. 8 AutoMute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Language ......................................... 8 IntelliMute ..........................................8 Screen Saver ........................................9 Smart Power ........................................9 Low Car Voltage .....................................9 System Info .........................................9 Restore Defaults .....................................9Radar Alerts ..........................................10 Radar Detector-Detector Alerts .........................10 Laser Alerts ........................................10 Responding to Alerts ................................ 11Understanding Radar and Laser ......................... 12Understanding LIDAR .................................. 13Customer InformationSpecications ...................................... 14Maintenance ........................................ 14Limited 1-Year Warranty ............................... 15Product Service & Optional Accessories .................. 16Trademark Acknowledgement ............................17IntroductionIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsRAD450_MANL_vB.indd 1 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English2 3InstallationYour Detector InstallationIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsInstallation •Where to mount your unitYou will get optimum performance from your detector if you mount it at a point approximately in the center of the vehicle, as low as possible on the front windshield without obstructing the unit’s view of the road either to the front or rear. You can also mount it directly on the dashboard. The unit’s lens must not be blocked and the LaserEye should have a clear view out the back window to allow maximum detection. Radar and laser signals pass through glass but not through other materials and objects. Objects that can block or weaken incoming signals include: n Windshield wiper blades n Mirrored sun screens n Dark tinting at the top of the windshield n Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM). Consult your dealer to see if you have this option.Windshield Mounting Dashboard Mounting1. Attach the rubber cups to the bracket.2. Make sure the rubber cups and your windshield are clean.3. Push the bracket rmly onto the windshield.4. Attach the detector to the bracket. Check that the unit is parallel to the road’s surface.5. To adjust the angle if necessary, gently push or pull on the bracket to bend it. DO NOT use the detector to bend the bracket.6. Plug the power cord into the detector.7. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter.The LaserEye should have a clear viewWindshield mountingRAD450_MANL_vB.indd 2-3 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®5Getting StartedYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsEnglish4InstallationYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary Icons NOTE: In some vehicles, power is supplied to the cigarette lighter even while the ignition is Off. If this is the case with your vehicle, you should turn Off or unplug your detector when parking for lengthy periods.1. Place the detector on the dashboard to nd a location where the unit has a clear, level view of the road and is parallel to the road’s surface. The angle CANNOT be adjusted after mounting2. Remove the paper backing from one side of the hook-and-loop fastener.3. Attach the pad to the dashboard at your chosen location and remove the other paper backing.4. Attach the detector to the hook-and-loop fastener. You can remove and reattach the unit as often as you like.5. Plug the power cord into the detector.6. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter.Dashboard Mounting Getting Started •To Turn On The Unit And Adjust The Audio VolumeRotate the On-Off/Volume controlclockwise (awayfrom you).Audible Tone Visual Display“Testing”Three beeps“System Ready”Icon Sens Level ForHigh No ltering for maximum rangeMedium Minimal ltering to reduce unwanted alertsLow Maximum ltering to reduce unwanted alertsSEN ButtonSetting your detector to Low or Medium sensitivity delays the audio alerts for weak X band and K band signals until they become stronger. (A single beep will sound when the signal is rst detected.) Also, additional ltering is done to reduce false alerts while you are driving in, or near, urban areas where there are many sources for conicting X and K band signals such as microwave towers and automatic door openers.Premium Anti-Falsing Circuitry Your RAD 450 is designed to provide you the truest alerts and minimize the distraction of erroneous signals from radar-based xed-position and moving sources. • Adjustable Sensitivity: High/Medium/Low modes allow driver to adjust sensitivity to driving environment, reducing false alarms from xed position sources such as automatic door openers.• IVT Filter: updatable system automatically reduces false alerts from moving In-Vehicle Technology sources such as collision avoidance systems and adaptive cruise control.RAD450_MANL_vB.indd 4-5 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English6 7Settings SettingsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsQuiet Drive is a muted driving mode for times when a driver wants less audible feedback while talking with passengers, on the phone, etc. Only the rst few seconds of audio will be heard. This mode is Off by default. This mode can be changed in the User Settings menu or by pressing and holding the MUTE button for two seconds. When Quiet Drive is on the audio icon on the display will change to: Battery VoltageTo display your vehicle’s battery voltage, press the MUTE button while no signal is being detected.DIM ButtonYou can choose from four settings for the brightness of the display. Repeatedly push the DIM button to cycle through the settings. The factory setting is Bright.Menu - User Settings •To change the User settings enter the Menu by pressing the MENU button. A voice announces “Menu” and the display will change toPress the DIM button to enter the User settings menu.Press the MUTE or MENU buttons to switch between the User settings.Press the DIM or SEN buttons to change the selected User setting’s value. The value that is shown on the display is the selected value. To exit the menu simply wait several seconds or select Exit Menu.USER MENU ALERTUSER SETTING VALUEDetail More*/LessQuiet Drive Off*/OnAuto Mute Off/On*Voice Off/On*Language English*/SpanishIntelliMute Off*/On/SetScreen Saver Off/1 Minute*/3 MinuteSmart Power Off*/OnSystem Info Press the SEN button to display system information.Restore Defaults Press the SEN button to restore factory default settings then press SEN button again to conrm.Exit Menu Press the MUTE button to exit the menu.* = Factory default settingMenu - User Settings continued •Menu - Alert Settings •To change the Alert settings enter the Menu by pressing the MENU button. A voice announces “Menu” and the display will change toPress the SEN button to enter the Alert settings menu.Press the MUTE or MENU buttons to switch between the Alert settings.Press the DIM or SEN buttons to change the selected Alert setting’s value. The value that is shown on the display is the selected value. To exit the menu simply wait several seconds or select Exit Menu.USER MENU ALERTMUTE ButtonManual Mute: Your detector allows you to quickly turn OFF an audio alert by momentarily pressing the MUTE button. If you press the MUTE button a second time during the alert, the audio alert will be turned back ON. When an alert is being muted the audio icon on the display will change to: MENU ButtonRAD450_MANL_vB.indd 6-7 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English8 9Settings SettingsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsDetailIn the More detail mode, information about the radar band, signal strength and frequency will be displayed.In Less detail mode, only the threat level is displayed (see page 10).AutoMuteAutoMute will automatically reduce the audio volume of all alerts after four seconds for as long as the signal is detected. The factory setting for AutoMute is On.RADAR SETTING VALUEX Band Off/On*K Band Off/On*Ka Band Off/On*VG-2 Off*/OnSpectre Off*/OnExit Menu Press the MUTE button to exit the menu.* = Factory default settingMenu - Radar Settings continued •LanguageThe detector can be set to either English or Spanish for all text and voice audio.IntelliMuteINTELLIMUTE allows you to avoid alerts you don’t need to hear because you are stopped or moving slowly. By sensing the “revs” (RPMs) of your engine, INTELLIM-UTE knows when you are at low speed and automatically mutes alerts (except for strobe signals from emergency vehicles).Before INTELLIMUTE will work, you must set an activation point for your engine’srevs. Whenever the revs are below that point, INTELLIMUTE will begin muting. The activation point will be stored in memory and recalled each time the power is turned On. The factory setting is INTELLIMUTE Off.NOTE: INTELLIMUTE may not work with some vehicles because it cannot sensethe engine’s revs. In such cases, you can reduce unwanted audio alertsby using Auto Mute and SEN mode when appropriate. Screen SaverYour detector has a SCREEN SAVER mode. When SCREEN SAVER is turned On (factory default is 3 minutes), the screen will change to Dark from it’s Bright, Dim, or Dimmer setting after the time interval selected. While the screen is Dark, the scanner will be displayed dimly.NOTE: While SCREEN SAVER is activated, any alert will turn the display back on at the last brightness setting (Bright, Dim or Dimmer). Touching any button will also turn On the display. Smart PowerYour detector includes the SMARTPOWER feature that, when turned On, will put the unit into Low Power mode 15 minutes after the car’s engine has been turned Off.Before SMARTPOWER enters Low Power mode, you will hear three beeps and SMARTPOWER will ash on the display. To return the unit to Normal Power mode and exit Low Power mode, start the car, press any button or turn the unit Off and then On again. Low Car VoltageDisplays your car battery voltage and automatically warns you if this drops below 11.9V. Your detector will then shut off to prevent further draining of your car battery.System InfoDisplays information about the versions of software/rmware that are installed on your detector. Restore DefaultsTo return your detector to factory default settings, press the SEN Button. Press the SEN Button again to conrm that you want to restore factory settings. Press the MUTE Button to exit.RAD450_MANL_vB.indd 8-9 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English10 11Settings and Detection DetectionYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsRadar Alerts •In More detail mode the radar band, signal strength and frequency of the detected radar signal will be displayed.If you are a new user of radar detectors, you may want to use the Less detail mode. In this mode the display will only show one, two, or three bars which indicate how likely the alert is to be a police radar or laser gun. This threat level indication takes into account the laser or radar band, strength, and frequency of the detected signal.Level Display Threat1Low2Medium3HighPolice use radar detector detectors (RDDs) to spot users of radar detectors.Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+RDDs and can provide alerts when any of these or similar devices are in usenear your vehicle.Radar Alerts - Radar Detector-Detectors •Laser Alerts •With Laser signals you will always receive a full strength alert. In More Detail mode the word Laser will be shown on the display along with the pulse rate of the Laser signal. In Less Detail mode three signal strength bars will be shown.Description Interpretation Recommended ResponseTone repeats slowly at rst, then speeds up rapidly.Probably police radar. FULL ALERTTone sounds one time only. Probably a false alarm, but possibly pulsed radar or VG-2 nearby.Exercise cautionTone instantly begins repeating rapidly.Radar or VG-2 nearby has been activated suddenly.FULL ALERTTone repeats slowly as you approach a hill or bridge, then speeds up sharply as you reach it.Probably police radar beyond the hill or bridge.FULL ALERTTone repeats slowly for a short period.Probably a false alarm. Exercise cautionAny type of laser alert. Laser alerts are never false alarms.FULL ALERTResponding to AlertsRadar Band FrequencySignal StrengthRAD450_MANL_vB.indd 10-11 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English12 13DetectionYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsYour DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsUnderstanding Radar and Laser •Radar Speed Monitoring SystemsThree band frequencies have been approved by the Federal Communications Commission (FCC) for use by speed monitoring radar equipment: X band 10.525 GHz K band 24.150 GHz Ka band 33.400 – 36.00 GHzYour detector detects signals in all three radar bands, plus Ku band (13.435 GHz), which is an approved frequency used in parts of Europe and Asia.VG-2 VG-2 is a “detector detector” that works by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be detected by VG-2, but does detect VG-2 signals and will alert you when a device is in use near your vehicle. While no signal is being detected, press and hold the Dim button for four seconds.Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 andSpectre I RDDs. You can choose whether you want to be alerted to VG-2 andSpectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+alerts is Off. It is recommended to leave these Off unless you are concerned about being monitored for having a radar detector.The factory setting for VG-2 alerts is Off. LIDAR (Laser)The correct name for the technology that most people refer to as laser is actually LIDAR, which stands for Light Detection and Ranging.LIDAR operates much like radar. Its signal spreads out like a radar signal, though not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles, tree branches, etc., will prevent valid speed measurement.Some common questions about LIDAR include: n Does weather have any affect on LIDAR? Yes. Rain, snow, smoke, fog or airborne dust particles will reduce the effective range of LIDAR and can, if dense enough, prevent its operation. n Can LIDAR operate through glass? Yes. Newer LIDAR guns can obtain readings through most types of glass. However, the laser pulse also can be received through glass to trigger an alarm by your detector. n Can LIDAR operate while in motion? No. Because LIDAR operates by line of sight, the person using it cannot drive the vehicle, aim and operate the gun all at the same time. n Is it legal for police to use LIDAR? Yes, LIDAR is allowed to be used in all 50 States by police. Your detector detects LIDAR (laser).Understanding LIDAR &MaintenanceRAD450_MANL_vB.indd 12-13 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®15Your DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsEnglish14Your DetectorIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsSpecications &MaintenanceU.S. Patent Number: 6,078,279 Specications •Band and FrequenciesWARNING Modications or parts substitutions not approved by Cobra Electronics Corporation may violate FCC Rules and void your authority to operate this equipment.Band FrequenciesX Band 10.525 ± 0.050 GHzK Band 24.125 ± 0.125 GHzKa Band 34.700 ± 1.300 GHzLaser 910 ± 50 nm 100 PPS VG-2 11.500 ± 0.250 GHzMaintenance •Your detector is designed and built to give you years of trouble-free performance without the need for service. No routine Maintenance is required.If your unit does not appear to be operating properly, please follow these troubleshooting steps:n Make sure the power cord is properly connected.n Make sure the socket of your vehicle’s cigarette lighter is clean and free of corrosion.n Make sure the power cord’s cigarette lighter adapter is rmly seated in your cigarette lighter.WarrantyLimited 1-Year Warranty •Cobra Electronics Corporation warrants that this product and the component parts thereof, will be free of defects in workmanship and materials for a period of one year from the date of rst consumer purchase. This warranty may be enforced by the rst consumer purchaser. If the product is under warranty, it will be repaired or exchanged depending on the model as determined at Cobra’s sole discretion. Such remedy shall be your sole and exclusive remedy for any breach of warranty. The procedure for obtaining service and support, and the applicability of this warranty, will vary depending on the country or jurisdiction in which you purchased and utilize the product. For the details on obtaining product service, support and warranty please visit www.cobra.com/supportProvided that the product is utilized within the U.S.A.- Cobra will, without charge, repair or replace, at its option, defective products, products or component parts upon delivery to the Cobra Factory Service department, accompanied by proof of the date of rst consumer purchase, such as a duplicated copy of a sales receipt. You must pay any initial shipping charges required to ship the product for warranty service, but the return charges, to an address in the U.S.A., will be at Cobra’s expense, if the product is repaired or replaced under warranty. This warranty gives you specic legal rights, and you may also have other rights which may vary from state to state and country to country. Exclusions: This limited warranty does not apply: 1) To any product damaged by accident; 2) In the event of misuse, ordinary wear, failure to follow directions, or improper maintenance of the product or as a result of unauthorized alterations or repairs; 3) If the serial number has been altered, defaced, or removed; 4) If the product was purchased or is utilized in a jurisdiction not covered by the limited warranty.All implied warranties, including warranties of merchantability and tness for a particular purpose are limited in duration to the length of this warranty. Cobra shall not be liable for any incidental, consequential or other damages; including, without limitation, damages resulting from loss of use or cost of installation.Some states and countries do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state and country to country.RAD450_MANL_vB.indd 14-15 3/30/16 12:04 PM
Nothing Comes Close to a Cobra®English16 17Product Service and Support •For any questions about operating or installing this new Cobra product, PLEASE CONTACT COBRA FIRST…do not return this product to the retail store. The contact information for Cobra will vary depending on the country in which you purchased and utilize the product. For the latest contact information, please go to www.cobra.com/supportFor products purchased in the U.S.A. you may also call 1-773-889-3087.For Products Purchased in the U.S.A., if your product should require factory service, please go to www.cobra.com/support and follow the instructions for returning your product to the Cobra Factory Service Department for service.Optional Accessories •You can nd quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra at www.cobra.comStraight 12V DC Power CordIncludes plug and fuseItem #420-030-N-001Windshield Mounting BracketIncludes suction cupsItem #545-159-N-001Product Service & Support and Optional Accessories Customer InformationIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsCoiled 12V DC Power CordIncludes plug and fuseItem # 420-026-N-001Dual Port Power AdapterIncludes adjustable plug (up to 90˚) and fuse Item # CLP-2BStraight Combination Radar USB CordIncludes plug and USB OutputItem # PWR USB-01Hardwire Cord for Radar Includes fuse Item # RA-PSCBInstall Mount Includes 3M Dual Lock Item # 545-002Customer InformationIntro Operation CustomerAssistanceWarrantyNoticeMain IconsSecondary IconsTrademark AcknowledgementTrademark Acknowledgement •Cobra®, DigiView®, EasySet®, Extra Sensory Detection®, LaserEye®, Nothing Comes Close to a Cobra®, VG-2 Alert®, Xtreme Range Superheterodyne® and the snake design are registered trademarks of Cobra Electronics Corporation, USA.Cobra Electronics Corporation™, AURA™, IntelliLink™, IntelliScope™, IntelliView™, Revolution™ Series, IVT Filter™, SmartPower™, Super-Xtreme Range Superheterodyne™, S-XRS™, and Voice Alert™ are trademarks of Cobra Electronics Corporation, USA.Instaclear® for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear® for GM is a registered trademark of General Motors Corporation. LTI Laser™ and LTI 20-20™ are trademarks of Laser Technology, Inc. Kustom Laser™, Kustom Laser 340™ and ProLaser II™ are trademarks of Kustom Signals, Inc. SpeedLaser™ is a trademark of Laser Atlanta. Stalker™ LIDAR is a trademark of Applied Concepts, Inc. Spectre I™ and Spectre IV™ are trademarks of Stealth Micro Systems Pty. Ltd. SpeedLaser™ is a trademark of Laser Atlanta, LLC. Interceptor VG-2™ is a trademark of TechniSonic Industries LTD. RAD450_MANL_vB.indd 16-17 3/30/16 12:04 PM

Navigation menu