Cobra Electronics FRS307C FRS Transceiver User Manual

Cobra Electronics Corporation FRS Transceiver Users Manual

Users Manual

FPOOperating Instructions for Your Cobra® microTALK®2-WAY RADIO MODEL FRS 307-2 VPOperating Instructions for Your Cobra® microTALK®2-WAY RADIO MODEL FRS 307-2 VPOperating Instructions for Your Cobra® microTALK®2-WAY RADIO MODEL FRS 307-2 VPNothing comes close to a Cobra™Nothing comes close to a Cobra™Nothing comes close to a Cobra™English, pages 1-16French, pages 17-32Spanish, pages 33-46(ENGLISH)(FRENCH)(SPANISH)(ENG)(FR)(SPAN)
Product Features• TWO-WAY RADIO with up to a 2 mile (3 km) range• 14 CHANNELS• 38 CTCSS PRIVACY CODES• UHF FM frequencies• BACKLIT LCD display• EXTERNAL SPEAKER/MICROPHONE jack• 10 MEMORY LOCATIONS• FULL CHANNEL/CTCSS SCAN• MEMORY SCAN• DUAL WATCH• MAXIMUM RANGE extender• 5 CALL SIGNAL SELECTIONS• VOX MODE for hands-free transmissions• selectable "ROGER BEEP" confirmation tone• selectable KEYSTROKE TONES• AUTO SQUELCH• CALL ALERT• BATTERY SAVER circuitry• LOCK button• BELT CLIP• WRIST STRAP• WATER RESISTANT• 2 NiMH BATTERY packs• 2-PORT DESKTOP RAPID CHARGER• 2 EARBUD MICROPHONESInstalling or Replacing Batteries1. Pull down the LOCK tab to remove the battery compartment cover.2. Insert your NiMH battery pack or four AAAbatteries. Position batteries according topolarity markings. (NOTE: NiMH batteriesare included with your microTALK®radio.When not using your NiMHs, always usehigh quality alkaline batteries. RechargeNiMH battery pack according to theinstructions for the FA-CJ charger.) Only the Cobra®NiMH battery pack(included) can berecharged using therecharging pads onthe back of the unit.See page 16 for optional accessories.OPERATION ENGLISH1OPERATIONENGLISH2This device complies with part 15 of the FCCrules. Operation is subject to the condition thatthis device does not cause harmful interference.FCC Warnings: Replacement or substitutionof transistors, regular diodes or other parts of a unique nature, with parts other than thoserecommended by Cobra,®may cause a violation of the technical regulations of part 95 of the FCC Rules, or violation of TypeAcceptance requirements of Part 2 of the Rules.ON-OFF/POWER buttonbacklit LCD displayLOCK buttonMODE buttonVOLUME UP& DOWNbuttonsCHANNEL SELECT buttonsspeaker/microphonebelt clipCALL buttonTALKbuttonLIGHT/MAXRANGEbuttonAntennaLock tabbattery compartmentbattery charger padsLOCK tabexternal speaker/microphone jackLIGHT/MAXRANGE buttonTALKbutton
O P E R AT I O NSelecting a CTCSS Privacy CodeCTCSS (Continous Tone Coded SquelchSystem) is an advanced tone coding systemallowing you to select one of 38 privacy codesto reduce interference from other users on thechannel. (NOTE: If you are using a privacycode, both radios must be tuned to the samechannel and privacy code to communicate.Each channel will remember the last privacycode you selected.) To select a privacy code:1. After selecting a main channel, press andrelease the MODE button. A small numberwill flash next to the channel in the LCD.2 . Push the CHANNEL SELECT button up ordown to select a privacy code. You can holdthe button up or down for fast advance.3. When your desired privacy code is displayed,p ress and release the LOCK button or pre s smode to enter selection and go to the nextf u n c t i o n .Calling Another PersonTo alert another person that you are calling:1 . P ress and release the CALL button. The otherperson will hear a 2-second ringing tone.You cannot send or receive transmissionsduring the 2-second call tone. (See page 13 for instructions on how to select between 5 call tone settings.)O P E R AT I O NENGLISH4CALL buttonLOCK b u t t o nM O D Eb u t t o nCHANNEL U PC H A N N E LD O W NTurning On Your microTALK®Radio1. Press and hold the ON/OFF POWER button for 2 seconds. A series of audibletones will indicate the radio is on.2. Your microTALK®is now in Standby mode,ready to receive transmissions. The radio isalways in Standby mode except when theTALK, CALL, or MODE buttons are pressed.(For Advanced Features accessed throughthe MODE button, see page 7.)Illuminating the Display1. Press and release the LIGHT/MAX RANGEbutton to illuminate the display for 10 seconds.Battery IndicatorWhen only one segment of the batteryindicator is blinking, the battery power is lowand you should rechargeyour FA-BP battery packor change your AAAalkaline batteries.Auto Battery SaveYour microTALK®radio has a unique circuitdesigned to extend battery life. If there are notransmissions within 10 seconds, the unit willautomatically switch to Battery Save modeand POWER SAVER willappear in the display.This will not affect theunit’s ability to receiveincoming transmissions.Selecting a Channel1. With the radio on, select any of the 14 channels by pushing the CHANNEL UPor CHANNEL DOWN button. (NOTE: Both radios must be tuned to the same channel to communicate.)ENGLISH3ON-OFF/POWER b u t t o nLIGHT/MAX RANGEb u t t o nCHANNEL U PC H A N N E LD O W N
O P E R AT I O NUsing the Lock FunctionThe Lock function locks the CHANNEL, MODE,and POWER buttons to prevent accidentaloperation. To use the Lock function:1. While in Standby mode, press and holdthe LOCK button for one second. The Lock icon will be visible when the unit is locked. Buttons that are NOT locked are the CALL,VOLUME, LIGHT/MAX RANGE, and TALKbuttons, which are all fully functional whilethe unit is locked.2. To “unlock” buttons, press and release the LOCK button again. The Lock icondisappears and all buttons will beunlocked.External Speaker/Microphone JackYour microTALK®radio can be fitted with anexternal speaker/microphone, freeing yourhands for other tasks. (Earbud microphonesare included with your FRS 307-2 VP–seeenclosed instruction sheet. For additionalaccessories (sold separately) see page 16.)To attach an external speaker/microphone:1. Open the SPKR/MIC tab on top of the unit.2. Insert the plug into the SPKR/MIC jack.Using the MODE buttonThe MODE button allows you to use andprogram the various functions of yourmicroTALK®radio. If you press and hold theMODE button, the LCD will cycle through thedifferent functions.O P E R AT I O NENGLISH6e x t e rnal micro p h o n es p e a k e rs p e a k e r / m i c ro p h o n ej a c kLOCK buttonM O D Eb u t t o nTalking to Another Person1. Press andhold the TALK button.2 . With the micro p h o n eabout 2 inches (5 cm)f rom your mouth, speak in a normal voice.3. Release the button when you’re finishedtalking and listen for a response. You cannot receive incoming calls while pressing the TALK button.“Roger Beep” Confirmation ToneYour listener will hear an audible tone when yourelease the TALK button. This alerts the other part ythat you are finished talking and it is OK for themto speak. (NOTE:The Roger Beep can be turn e do ff and on, see page 12.)Listening for a ResponseWhen you are finished talking:1 . Release the TALK button to receive i n c o m i n gt r a n s m i s s i o n s . The radio is always in Standbymode except when the TALK, CALL, or MODEbuttons are pre s s e d .2. Adjust the volume by pressing and holdingthe VOLUME UP or VOLUME DOWN buttons.Auto SquelchYour microTALK®radio is equipped with AutoSquelch, which automatically shuts off weaktransmissions and unwanted noise due toterrain, conditions, or if you’ve reached yourmaximum range limit. (NOTE: To learn moreabout the range of your microTALK®radio, see page 13.)Maximum Range ExtenderYou can temporarily turn off Auto Squelch,allowing all signals to be received andextending the maximum range of your radio:1. Press and hold the LIGHT/MAX RANGEbutton for 5 seconds. You will hear 2 beeps indicating that Maximum RangeExtender is on.2. To turn Maximum Range Extender off, pressand hold the LIGHT/MAX RANGE button for1 second, or change channels.ENGLISH5TALK button L I G H T / M A XRANGE button
O P E R AT I O NO P E R AT I O N • A D VANCED FEAT U R E SProgramming MemoryLocationsYour microTALK®radio has 10 memorylocations (0-9) for storing your mostfrequently used channels and privacy codes.To program locations:1. Push the MODEbutton until theMemory icon and the memorylocation flashes.2. Select the memorylocation you wish tochange by pushingthe CHANNEL SELECTbutton up or down.3. Press and release the MODE button again.The Memory icon and the main channelnumber will flash.4.Select the main channel you wish to s t o re bypushing the CHANNEL SELECT button up ord o w n .5. P ress the MODE button again to store themain channel in memory and move toprivacy code selection. The privacy codenumber begins flashing and the Memoryicon continues to flash.6. Select the privacy code (0-38) you wish to store by pushing the CHANNELSELECT button up or down.7. Press the TALK buttonto transmit on yourselected channel andprivacy code, which will be stored into the memory location you are using.8. Press and release the LOCK button toreturn to Standby mode at your newmemory location, or press and release theMODE button to save the memory locationand proceed to other functions.ENGLISH8M O D Eb u t t o nTALK b u t t o nMODE buttonMODE buttonL O C Kb u t t o nMODE b u t t o nCHANNEL SELECT b u t t o nUsing VOX ModeIn VOX mode, your microTALK®can be used"hands-free," automatically transmitting whenyou speak. To turn VOX mode on and off:1. Press the MODE button until the VOX iconflashes and the current setting ("on" or"off") is displayed.2. Push the CHANNEL SELECT button up ordown to turn VOX mode on or off.3. Press and release the LOCK button to enterthe new setting, or press the MODE buttonto enter the new setting and proceed toother functions.Setting the VOX Sensitivity LevelYou can set the VOX sensitivity level to fit thevolume of your voice and avoid transmissionstriggered by background noise. To set thesensitivity:1. Press the MODE button until the VOX icon flashes and the number for the current sensitivity level is displayed next to the letter L (level 5 = most sensitive,level 1 = least sensitive).2. Push the CHANNEL SELECT button up ordown to change the setting.3. Press and release the LOCK button to enterthe new setting, or press the MODE buttonto enter the new setting and proceed toother functions.ENGLISH7M O D Eb u t t o nLOCK b u t t o nMODE b u t t o nC H A N N E LU PC H A N N E LD O W NC H A N N E LU PC H A N N E LD O W NM O D Eb u t t o n
OPERATIONOPERATIONUsing the Scan Function(continued)To scan privacy codes:1. While in Standby mode, press the CHANNEL SELECT button up or down tochoose the main channel you wish to scan.2. Press the MODE button until the Scan icon and the privacy code number flashes.3. Push the CHANNEL SELECT button up or down and the unit will begin scanning privacy codes within the main channel you selected.4. The radio will continue to scan privacycodes and stop if an incomingtransmission is detected. The unit willremain on that code for 10 seconds.During that time you can:a) Press and hold the TALK button and talk.The radio will remain on that channel andprivacy code, then return to Standby mode.b) Push the CHANNEL SELECT button up ordown to resume scanning privacy codes.c) Press the MODE button to proceed to memory location scanning.If you do not press any button within 10 seconds, the radio will automaticallyresume scanning privacy codes.To scan memory locations:1. Press the MODE button until the Scan icon,Memory Location icon and memorylocation number flashes.2. Push the CHANNELSELECT button up ordown and the unit will begin scanningmemory locations.ENGLISH10MODE buttonTALK buttonMODE buttonCHANNEL SELECTbuttonCHANNEL SELECT buttonMODE buttonCHANNEL SELECT buttonRecalling Memory LocationsTo recall a channel you have stored in amemory location:1. Press the MODE button until the Memoryicon and a memory location flashes.2. Select your desiredmemory location by pushing theCHANNEL SELECTbutton up or down.Press the LOCK button to enter your selection. To go on to the nextfunction withoutselecting a memory location, press the MODE button.3. Repeat steps 1 and 2 to recall othermemory locations.Using the Scan FunctionYour microTALK®radio can automatically scan main channels (1-14), the privacy codes (0-38) within one main channel, or memory locations.To scan main channels:1. Press the MODE button until the Scan iconand main channel number flashes.2. Push the CHANNEL SELECT button up or down and the unit will begin scanningthe main channels. (NOTE: The unit“ignores” privacy codes while scanning main channels.)3. The radio will continue to scan all mainchannels and stop if an incomingtransmission is detected. The unit willremain on that channel for 10 seconds.During that time you can:a) Press and hold the TALK button and talk. The radio will remain on that channel and return to Standby mode.b) Push the CHANNEL SELECT button up or down to resume scanning mainchannels.c) Press the MODE button to proceed to privacy code scanning (see followingpage).If you do not press any button within 10 seconds, the radio will automaticallyresume scanning main channels.ENGLISH9MODE buttonCHANNEL SELECT buttonMODE buttonLOCKbutton
3. The radio will continue to scan all memorylocations and stop if an incomingtransmission is detected. The unit willremain on that location for 10 seconds.During that time you can:a) Press and hold the TALK button and talk.The radio will remain on that memorylocation channel and return to Standby mode.b) Push theCHANNEL SELECTbutton up or downto resume scanningmemory locations.c) Press the MODE button to proceed toother functions.If you do not press any button within 10 seconds, the radio will automaticallyresume scanning memory locations.Setting Dual WatchDual watch allows you to simultaneouslymonitor any two channels/privacy codes you select. To program Dual Watch:1. Select the first channel and privacy codeyou wish to monitor. (To review, see pages 3-4.)2. Press the MODE button until the DualWatch icon flashes.3. Push the CHANNELSELECT button up ordown to select thesecond channel you wish to monitor.4. Press the MODE button. The privacy codeflashes.5. Push the CHANNEL SELECT button up ordown to select the second privacy code.6. Press and release theLOCK button to storethe second channel/privacy code andengage Dual Watch.7. To terminate Dual Watch and return tonormal Standby mode, press and releasethe LOCK, TALK or MODEbutton.O P E R AT I O NENGLISHO P E R AT I O N ENGLISHTurning Roger Beep Off and OnWith Roger Beep turned on, your listener will hear an audible tone when you release theTALK button. To change Roger Beep mode:1. Press the MODE button until the RogerBeep icon flashes and the current setting(“on” or “off ” ) is displayed.2. Push the CHANNEL SELECT button up ordown to turn Roger Beep on or off.3. To enter the new setting you can press andrelease the LOCKbutton, or press nobuttons for 15 seconds. Press the MODEbutton to enter the new setting andproceed to other functions.Turning Keystroke Tones Off and OnWith Keystroke Tones turned on, your unit willsound beeps each time you press a button orchange a setting. To change Keystroke Tonesmode:1 . P ress the MODE button until the Keystro k etones icon flashes and the current setting(“on” or “off”) is displayed.2. Push the CHANNEL SELECT button up ordown to turn Keystroke Tones on or off.3. To enter the new setting you can press andrelease the LOCKbutton, or press nobuttons for 15 seconds. Press the MODEbutton to enter the new setting andproceed to other functions.12MODE buttonMODE b u t t o nCHANNEL UPCHANNEL DOWNCHANNEL UPCHANNEL DOWNLOCK buttonMODE button11MODE buttonMODE buttonCHANNEL SELECT b u t t o nCHANNEL SELECT b u t t o nTALK buttonLOCK b u t t o n
O P E R AT I O N LI M IT ED 2- Y E AR WA R R A N T YENGLISH14Customer AssistanceAfter reading this owner’s manual, if you have any questionsabout installing or operating your microTALK®radio, or if youare missing any parts, please contact Cobra®first. Do notre t u rn this product to the store. C o b r a®E l e c t r onics offers thefollowing customer support services.•Automated Help Desk is available 24 hours a day, 7 days a week at 773-889-3087.• Customer Service Operators are available atthe same number 8:00 a.m. to 6:00 p.m. CSTMonday through Friday (except holidays).• Questions can be faxed to 773-622-2269.• Technical assistance is available on-line in the Frequently Asked Questions (FAQ) section at www.cobra.com or by e-mail to productinfo@cobra.com.If your product should require factory service please call Cobra®first before sending your unit in. This willensure the fastest turn-around time on your repair.You may be asked to send your unit to the Cobra®factory.It will be necessary to furnish the following in order to have the product serviced and returned.1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction or carbonof a sales receipt. If you send the original receipt it cannot be returned.2. Send the entire product.3. Enclose a description of what is happening with the unit.Include a typed or clearly printed name and address ofwhere the unit is to be returned.4. Pack unit securely to prevent damage in transit. If possible, use the original packing material.5. Ship prepaid and insured by way of a traceable carrier suchas United Parcel Service (UPS) or First Class Mail to avoidloss in transit to: Cobra®F a c t o ry Service, Cobra Electro n i c sC o r p o r a t i o n , 6500 W. Cortland St., Chicago, IL 60707.6. If the unit is in warranty, upon receipt of your unit it willeither be repaired or exchanged depending on the model.Please allow approximately 3-4 weeks before contactingus for status. If the unit is out of warranty a letter willautomatically be sent informing you of the repair charge or replacement charge. If you have any questions, pleasecall 773-889-3087 for assistance.FOR PRODUCTS PURCHASED IN U.S.A.Cobra Electronics Corporation warrants that its Cobra ®FRSRadios, and the component parts thereof, will be free of defects in workmanship and materials for period of two (2) years from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser,provided that the product is utilized within the U.S.A.Cobra®will, without charge, repair or replace, at its option, defective FRS radios, products or component parts upon delivery to the Cobra®F a c t o ry Service Department, accompanied by proof of the date of first consumer purchase, such as a duplicated copyof a sales re c e i p t .You must pay any initial shipping charges required to ship the product for warranty service, but the return charges willbe at Cobra's expense, if the product is repaired or replacedunder warranty.This warranty gives you specific legal rights, and you may alsohave other rights which vary from state to state.Exclusions: This limited warranty does not apply 1) to any pro d u c tdamaged by accident; 2) in the event of misuse or abuse of thep roduct or as a result of unauthorized alterations or repairs; 3) if the serial number has been altered, defaced or removed; 4) if the owner of the product resides outside the U.S.A. All implied warranties, including warranties of merchantabilityand fitness for a particular purpose are limited in duration to the length of this warranty. Cobra®shall not be liable for any incidental, consequential or other damages; including, withoutlimitation, damages resulting from loss of use or cost of installation.Some states do not allow limitations on how long an impliedwarranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitationsmay not apply to you.Changing Call Tone SettingsYou can choose between five different calltone settings to transmit a unique call alert. To select a call tone setting:1 . With the power turned off, press and hold theCALL button as you turn the power on. Thenumber of the current call tone setting willflash and the tone will sound for one second.2. Push the CHANNEL SELECT button up ordown to hear the othercall tone settings.3. With the numberof your desiredcall tone settingdisplayed, pressand release theTALK button orLOCK button. Your selection will be entered.4. If no buttons are pushed for 15 seconds,the unit will automatically enter the lastcall tone pattern that was displayed.microTALK®RangeYour microTALK®radio has a range of up to 2miles (3 km). Your range will vary dependingon terrain and conditions. In flat, open countryyour radio will operate at maximum range.Buildings and foliage in the path of the signalcan reduce the range. Dense foliage and hillyterrain will further reduce the signal.Remember, you can achieve maximum range by using Maximum Range Extender.(See page 5.)ENGLISH13CALL buttonPOWER buttonC H A N N E LU PC H A N N E LD O W NLOCK button
15A C CES SOR IES • ORD E R FOR MENGLISH16Name _____________________________________________________________________Address (No P.O. Box) ___________________________________________________________City ____________________ State/Province ______________ Zip___________ Country _ ______Telephone (___) _________________________ Circle One: Visa MasterCard DiscoverCredit Card No. ___________________________________ Exp. Date _____________________Customer Signature_____________________________________________________________Vox Headset MicMA-VOX Ear Bud Mic with PTTM A - E B MLapel Speaker/Microphone M A - S MReplacement Belt ClipFA - B C 42 Port Desktop NiMH ChargerFA - C FNiMH RechargeableBattery PackFA-BPU.S. Subtotal(Tax if applicable) Shipping/handlingTotal Canada AmountG.S.T.7%*QST 7.5% Shipping/ handling Total *Quebec residents onlyOrdering from Canada(Call 514-683-1771 for pricing)Order by phone:Call 514-683-1771 (Press 1 from the main menu) 9 a.m. - 5p.m., M-F, EST.Order by e-mail:cobraextras@avs.caOrder by mail or fax:Pleasefill out order form below,and mail/fax directly to: AVS Technologies Inc.2100 Trans Canada Hwy. S.Montreal, Que. H9P 2N4Fax to: 514-683-5307Please allow 4-6 weeks for delivery in Canada. Prices subject to changewithout notice.Item # US Cost Ea. Canada Cost Ea. Qty. Amount$5.50Ordering from U.S.Call 773-889-3087 for pricing or visitwww.cobra.com For credit card orders fillout order form and fax to 773-622-2269Or call 773-889-3087(Press 1 from the mainmenu) 8:00 am-6:00 pm,M-F, CST.Make check or moneyorder payable to:Cobra®Electronics Attn: Accessories Dept.6500 West Cortland St.Chicago, IL 60707Please allow 2-3 weeks for delivery in U.S.Prices subject to changewithout notice.Tax TableIllinois add 8.75%Indiana & Wisconsin add 5% Michigan & Ohio add 6 %$25.00 and under$ 2 5 . 0 1-$4 0 . 0 0$ 4 0 . 0 1-$ 8 0 . 0 0$ 8 0 . 0 1-$ 1 2 0 . 0 0$ 1 2 0 . 0 1-$ 1 6 0 . 0 0$160.01 and up$4.75$6.95$ 9 . 2 5$ 1 0 . 2 5$ 1 1 . 7 5$14.50Amount Shipping/Handling For AK, HI and PR please add an additional $15.00 for UPS shipments.To order online,please visit our website:www.cobra.comClick “shop Cobra®”WA RRANTY •C US TO ME R ASS ISTA N C E • S P E C I F I C AT I O N SA. FREQUENCIESCHANNEL ASSIGNMENTCH 1: 462.5625MHz CH 8: 467.5625MHz CH 2: 462.5875MHz CH 9: 467.5875MHz CH 3: 462.6125MHz CH 10: 467.6125MHz CH 4: 462.6375MHz CH 11: 467.6375MHz CH 5: 462.6625MHz CH 12: 467.6625MHz CH 6: 462.6875MHz CH 13: 467.6875MHz CH 7: 462.7125MHz CH 14: 467.7125MHz B. RECEIVER UNIT NOMINAL1. SENSITIVITY FOR 12 DB SINAD dBm -121FOR CALL SIG DETECTION dBm -1212. MAX. AUDIO OUTPUT @10% THD mW 2003. MAX. S/N RATIO @ 1mV RF INPUT dB 504. SQUELCH a) SENSITIVITY dB m -121b) ATTACK TIME mS 150c) CLOSING TIME mS 2005. AUDIO FREQUENCY RESP.@ 300 HZ dB -3@ 2500 HZ dB -106. SIGNAL DISPLACEMENT BW +/-KHZ 57. ADJACENT CH. REJECTION dB 608. INTERMODULATION REJECTION dB 659. SPURIOUS RESPONSE REJECTION dB 55C. TRANSMITTER UNIT NOMINAL1. POWER mW 5002. CARRIER FREQ. STABILITY +_H z 5003. MODULATION LIMITING KHz 2.54. CARRIER ATTACK TIME mS 305. AUDIO FREQUENCY RESPONSE@ 300 HZ dB -10@ 2500 HZ dB 46. AUDIO DISTORTION % 37. HUM NOISE dB 388. TRANSIENT FREQ. BEHAVIORa)TXON mS 30b) TXOFF mS 5D. POWER SUPPLY1. BATTERY LIFE (1:1:18 RATIO) HR 242. BATTERY OPERATING RANGE V 4.0 - 6.0General SpecificationsCustomer AssistanceAfter reading this owner’s manual, if you have any questionsabout installing or operating your microTALK®radio, or if youare missing any parts, please contact Cobra®first. Do notreturn this product to the store. Cobra®Electronics offers thefollowing customer support service.• Technical assistance is available on-line in the Frequently Asked Questions (FAQ) section at www.cobra.com or by e-mail to productinfo@cobra.com.For out of warranty service, ship prepaid this product to: AVS Technologies Inc., 2100 TransCanada Hwy S., Montreal,Quebec, H9P 2N4. We reserve the right to repair or replacethe unit with an equivalent product. Please include the following information:Date of purchase:Model No.:Dealer Purchased from:Dealer address:Dealer phone No.:FOR PRODUCTS PURCHASED IN CANADAYour new Cobra®FRS is covered by a two (2) year replacement w a rr a n t y. If any manufacturing defect becomes apparent in thisp roduct within two years from the original date of purchase, it will be replaced. Please re t u rn the FRS radio to your dealer withoriginal or copy of dated proof of purchase.This warranty does not cover damages due to careless handling,negligence, accident, abuse or failure to follow operating i n s t r uctions. Alteration of this product or defacing of the serialnumber cancels all obligations of this warr a n t y. This warr a n t ygives you specified legal rights. Additional warranty rights may be provided by law in some are a s .

Navigation menu