Codan 2310 2310 HF Radio System User Manual PDF File

Download:
Mirror Download [FCC.gov]
Document ID	3773811
Application ID	41bo0/3AL7dQL9qXvxarYg==
Document Description	User Manual B
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	255.17kB (3189652 bits)
Date Submitted	2018-03-08 00:00:00
Date Available	2018-09-03 00:00:00
Creation Date	2018-03-07 08:08:13
Producing Software	Microsoft: Print To PDF
Document Lastmod	2018-03-07 08:08:13
Document Title	PDF File
Document Author:	kimc

USING THE WIZARD
STARTlNG THE WlZARD
2| Repeat this for minutes, seconds and AM/PM values.
3 Press \— (Save) to save the local time.
J Press v to move to the Local Date entry.
3 Press ) to enter edit mode for the local date.
J Press A or v to scroll to the value that you want to set, then
press ) to move to the next item.
I Repeat this for the day/month and year, as required.
:I Pres ‘__(Save) to save the local date.
2| Press v to move to the Clock entry.
3 Press 1 or D to select the type ofclock that you want to use.
J Press v to move to the Time Format entry.
3 Press { or D to select the fomIat that you want to use.
2 Press v to move to the Date Format entry.
I Press { or > to select the fomIat that you want to use.
:I If you want to review the information that you have entered,
press A or v to move through the entries.
J Press ‘— (Save) to save the information.
Ifyou have not changed any ofthe time and date
information, press _' (Close).
Adding a channel
NOTE: This step in the wizard is shown ifyou are pemiitted
to add channels.
To add a channel:
Press \— (Yes) to add a channel, if required.
Enter the name that you want to use for the channel.
Press v to move to the Tx entry.
Enter the transmit frequency that you want to use for this
channel (in kIIz, with up to three decimal points or 1 Hz
resolution).
14
SEva-Hm TRANSCEIVER OPERATOR GUIDE
USING THE WIIARD
STARTlNG m5 WIZARD
2| Press v to move to the Rx entry.
The Rx entry is automatically filled with the transmit
frequency.
J Enter the receive frequency (in kIIz, with up to three
decimal points or 1 Hz resolution), if required to be
different from the Tx frequency.
3 Press v to move to the Mode entry.
J To select a mode:
- Press ) to view the list ofavailable modes.
- Press A or v to scroll to the mode that you want to
use, then press OK.
When the check box is selected, the item is enabled.
When the check box is clear, the item is disabled.
- Select other modes, as required.
NOTE: The modes that you select become the
allowed modes for this channel. In a
scan table, you can duplicate a channel
and select another ofthe allowed
modes.
- Press ‘— (Save).
2 Ifyou want to review the infomiation that you have entered,
press A or v to move through the entries.
I Press ‘— [Save) to save the information.
:| Do one ofthe following:
- Ifyou want to add another channel, pre ‘—
[Yes), then repeat these steps.
- Ifyou do not want to add another channel,
press _, (No).
The channels that you enter may be allocated to a scan table.
A scan table enables you to manage how these channels are
scanned using one set of properties.
SEmRv-Hm TRANSCEIVER DPERATOR GUIDE 15
USING me WIZARD
Sunnue YHE WIZARD
121 Do one of the following:
- Ifyou want to add a scan table, press a— (Yes).
- If you do not want to add a scan table, press _,
(No), then continue from Entering a sci/address on
page 161
I: Do one of the following:
- lfyou want to scan all ofthe channels in the
transceiver that have a USB mode. press \—
(Yos). then continue from Enteringa self address on
page 16.
- If you want to choose the channels and modes that
you want to scan, press —' (No), then continue
from Adding channels in a scan table on page 16.
Adding channels to a scan table
To add channels to a scan table:
a Press A or v to scroll to the channel that you want to add,
then press OK.
a Press 4 or b to select the mode that you want to use.
a Select more channels, as required.
a Press \— (Save) to add these channel selections.
I: Continue from Entering a self address on page 16.
Entering a self address
A self/address is used by other stations to cnll your station. For
example, ifthe self address of your station is 1234, operators at
other stations enter the address 1234 when they want to make a call
to you.
16 SEva-Hw TRANSCEIVER OPERATOR GUIDE
USING THE WIIARD
STARTlNG m5 WIZARD
To enter a self address:
:|
Enter the address that you want to use.
You can enter up to six digits, or you may leave the self
address blank ifa peripheral device has its own selfaddress
set.
NOTE: Addresses ending in one or more 9 or 0 digits
have a special function in Selcall HF
networks.
Press \— [Save) to save the information.
NOTE: The wizard automatically allocates this self
address to the default IIF networks: Selcall
and CALM.
Do one of the following:
- If you want to add a contact, press \-— (Y es). then
continue from Adding a contact on page 17.
- Ifyou do not want to add a contact, press _, (No),
then continue from Selecling an antenna on page 22.
Adding a contact
A contact is a person or organisation that you want to call. and for
which you want to pre-define the method of calling. You may be
able to contact the same person or organisation via a number of
different methods. When you set up the Contact, you define each
method as a separate call for the contact.
To add a contact:
Enter the name that you want to use for the contact, then
press ‘— (Add Call).
The HF Network entry is highlighted.
The HP network defines the call system and selfaddress that
is used by your station when the call is made.
Press 4 or D to select the [IF network that you want to use.
Press v to move to the Call Type entry.
SEmRv-Hm TRANSCEIVER OPERATOR GUIDE 17
USING ms WIZARD
SYARTING n4: WIZARD
El Press 4 or b to select the call type that you want to use.
NOTE: The call type that you select affects
information that you can enter for the
remainder of this call.
u If you are adding:
- a Selective, Channel Test, Emergency, Get Position
or Send Position call, continue from Adding a Simple
call on page 18
- a Message call, continue from Adding a Message
call on page 19
- a Phone call, continue from Adding a Phone call on
page 21
Related links:
Contactr on page 1 19
Adding a simple call
A simple call is a call that requires only an address at this stage of
the definition process.
To continue with adding a Selective. Channel Test, Emergency.
Get Position or Send Position call:
o Press v to move to the Address I Selcall Address |
ALE Address entry.
Add Call
‘Selcall A
Call Type
~ (all Adams
_|'
Save Close
1B SENTRV-H W TRANSCEIVER OPERATOR GUIDE
USING IHE WIIARD
SrARnuG YHE WIIARD
II
:|
Enter the address of the station that you want to call.
Continue from Completing the Contact on page 2].
Adding a Message call
To continue with adding a Message call:
Press 7 to move to the Address l Sslcsll Address l
ALE Address entry.
Enter the address of the station that you want to call.
Press v to move to the Message entry, then press >-
NOTE: lfyou want to be prompted to enter a message
at the time efthe call, leave the value for the
Message entry as .
Edit Message (0/64)
Optionsl Close
lfyon want to enter a message:
- Hold # to select a different input language, if
required. Ifyon are using a USB keyboard, press
Ctrl+Shift to select a different input language.
Start typing the message.
NOTE: Press OK to start a new line, if
required.
Press \— [Optianst scroll to Save, then
press \— (Select) to add the message to the call.
SENYRV-HW TRANSCEIVER DPERATOR GUIDE 19
USING THE WIZARD
STARTING THE WIZARD
2| Ifyou want to select a message from a list of stored
messages:
- Press \— (Optians), scroll to Stored, then
press ‘__ (Select).
Messages (1/10)
—
Message 2
Message 3
Message 4
Message 5
Message 6
- Press A or v to scroll to the message that you want
to use.
NOTE: Ifyou want to view the message,
press ‘— (Details) to view the
message, then press ‘— (Close).
- Press OK to select the message.
- Edit the message, ifrequired.
Ed ll Message‘ (20/90)
ease call me ba
Optionsl
Press \— (Options), scroll to Save, then
press \— (Select),
I:I Continue from Completing the mutual on page 2 l,
20 SENTlv-HW TRANSCEIVER OPERATOR GUIDE
USING IHE WIIARD
SuRnuo ms wtunn
Adding a Phone call
To continue with adding a Phone call:
:I
Press v to move to the Phone Number entry.
Enter the phone number.
Continue from Completing the can/act on page 21.
Completing the contact
To finish entering the information required for the Contact:
Press v to move to the Call Description entry.
The call type is entered automatically as the call description.
Enter a new description for this call, if required.
Press ‘— [Save) to save the information.
If you want to add another call for the contact, press \__
(Yes), then repeat the steps for adding a call.
If you do not want to add another call, press _' (No).
If you want to add another Contact, press ‘— [Yes), then
repeat the steps for adding a Contact.
If you do not want to add another contact, press —o (No).
Do one ofthe following:
- If you want to select an antenna, continue from
Selecting an antenna on page 22,
- If you do not want to select an antenna, press _,
(Close), then continue from Selecting a peripheral
device on page 22.
SENTRV-Hm TRANSCEIVER OPERATOR GUIDE 21
USING THE WIZARD
STARTING THE WIZARD
Selecting an antenna
Each type of antenna has a specific requirement for tuning, and the
transceiver uses a different protocol for each one. You must select
the type ofantenna that is used in your station so that the
transceiver knows how to tune the antenna. Some antennas, such as
broadband antennas, do not require tuning
To select an antenna:
2 Press A or v to scroll to the antenna type that you want to
use, then press OK.
El Press \— (Save) to save the information.
I: Do one of the following:
- If you want to connect an accessory to the GP port
connector of the RFU, press \__ (Yes), then
continue from SeIecting a peripheral device on
page 22.
- If you do not want to connect an accessory,
press —1(N0), then press OK to close the wizard.
Selecting a peripheral device
When you select the peripheral device fi'om the list, the transceiver
automatically sets these properties The default settings should be
adequate for most situations, however, if you have special
requirements, please see the Reference Manual [Codan part
number 15-04188-EN Issue 1) for more detailed information.
To select a peripheral device:
3 Press A or v to scroll to the type ofperipheral device that
is attached to the connector, then press OK.
Ifthere are settings that you can change to customise this
peripheral for your requirements, . s shown to the right of
the peripheral name when it is selected.
22
SEImw-Hw TRANSCEIVER OPERATOR GquE
USING THE WIIARD
STARTlNG m5 WIZARD
lfyou want to change settings for the peripheral, press ) to
see the list of entries that you may change.
lfthe value of an entry for a peripheral device has been
changed from the default value, 0 is shown next to the title
of the entry.
Pr ‘— [Save) to automatically update settings for
correct operation of the connected peripheral device.
Press OK to close the wizard.
lfyou added a peripheral device, and a prompt to restart the
transceiver is displayed, accept it to activate the new
settings.
SENYRV-HW TRANSCEIVER DPERATOR GUIDE 23
USING THE WIZARD
STARTING THE WIZARD
This page hag been lcfl blank imcmionally.
24 SEva-Hw TRANSCEIVER OPERATOR GUIDE
Operating the
transceiver
This section contains the following topics:
Switching [he transceiver on and of on page 26
The channel screen on page 27
Selecting a channel on page 31
Selecting a channel from a channel group on page 32
Scanning channels on page 35
Mating the transceiver on page 38
Using the microphune on page 39
Setting the basics on page 40
Calling on page 42
Using digital voice on page 59
Uxing GPS on page 68
Data optianx on page 78
Uxing encryption on page 89
Uxingfrequency hopping on page 99
Using a crasspateh on page 105
Using Codan Convoy on page 108
Using an external power amplifier on page 109
Upgrading the transceiver via a USB stick on page 1 13
Using GPS Platter on page 1 16
Using VCOMservices on page 1 17
SENTRv-H“ TRANSCEIVER OPEIA‘mR Gum: 25
OPERATING THE TRANSCEIVER
SWITCHING THE TRANSCEIVER ON AND OFF
Switching the transceiver on and off
Switching on the transceiver
To switch on (he transceiver:
3 Press A.
The splash screen then the welcome screen (ifset) are
shown briefly, followed by the channel screen.
Switching off the transceiver
To switch offlhe transceiver:
3 Do one ofthe following:
- Hold A for 2 see, then release.
- Press A, then press OK.
The transceiver is switched off.
26 SENTRv-Hw TRANSCEIVER OPERATOR GUIDE
OPERATING THE TRANSCEIVER
THE CHANNEL SCREEN
The channel screen
The channel screen shows the following information:
the name of the currently selected channel
NOTE: If hown before the chzmnel name,
then this channel is contained within a
channel group.
the transmit and receive frequencies, if applicable
the status areas that show specific information about the
transceiver
1| bar graph that indicates the signal strength on receive
(green) and the output power on transmit (red)
the transmit power level setting
the call type icon (when calling) or the scan indicator (when
scanning, see Figure 7)
the mute type indicator
a missed czill icon, ifapplicable
the mode
the crasspatch indicator, if connected
the clarifier indicator, if set
calling and system looks when the RFU is being used by a
connected data application or another control point (see
Figure 6).
SENTRV-Hm TRANSCEIVER OPEIA‘MR GUIDE 27
OPERATING THE TRANSCEIVER
THE CHANNEL SCREEN
Figure 5: Channel screen
mute type
Signal indIcator
strength Tx power call type (hlghllghted
Indicator setting icon when mute is on) _
mlssed call Icon
Rx/Tx
Indicator mode
USB
slalus bar
channel name —_ _ _ CH 05
n11,538 m11,555 I
Tx/Rx irequency
status areas
menu bar
—I
Ian software key rIght software key
volume Indlcator
NOTE: Ifyou cannot transmit on the channel, Inhibit is
shown as the Tx frequency.
If the transmit and receive frequencies are the same, the frequency
is only shown on the right side ofthe screen. The Rx/Tx indicator
shows whether the transceiver is receiving (green) or transmitting
(red). The more bars that are shown, the higher the signal strength.
The status area of the screen provides six separate areas in which
you can show information that is relevant for your operations. Your
system administrator can choose the information that is shown in
each status area. If encryptor/scrambler options are enabled, this
information is shown in the top line of the status area (status areas
1 and 2). Any selections that have been made are discarded.
NOTE: For information on how to set up what is shown in
the status areas, please see the Reference Manual
[Codan part number 15-04188-EN Issue 1).
23 SENTRV-H W TRANSCEIVER OPERATOR GUIDE
OPERAIING THE TRANSCEIVER
THE CHANNEL SCREEN
Your transceiver may have the option of selecting high, medium,
or low power, as set in Settings > Configuration > Tx Power.
By default, you can toggle between the Tx power settings by
pressing the 6 key. Hi, Med, or Lois shown respectively to the
right ofthe signal strength indicator. Ifan external power amplifier
is connected, PA may also be selected.
While a call is being established, the transceiver shows that calling
activity is in progress by flashing § in place ofthe scan indicator.
Once a call is established, these indicators are replaced with an icon
that represents the type of call being sent or received.
NOTE: For detailed information on call types, please see the
Reference Manual (Codan part
numberlS-O4lSX-EN Issue 1).
Figure 6: System lock and connected data application
icons
system lock connected data
Icon application icon
CH 01
10,000
When the transceiver is scanning, the channel screen is replaced by
the scanning screen.
SEva-Hm TRANSCEIVER DPERATOR GUIDE 29
OPERATING THE TRANSCEIVER
THE CHANNEL SCREEN
Figure 7: Scanning screen
scan indIcalDr
Scanning
enu
30 SENTRV-H W TRANSCEIVER OPERATOR GUIDE
OPERATING THE TRANSCEIVER
SELECTING A CHANNEL
Selecting a channel
To select a channel:
3 Press PTT to exit to the channel or scanning screen.
J Ifthe transceiver is scanning, press SCAN to switch off
scanning.
CH 01
10,000
14:12:36 0
J Press A or v to scroll to the channel that you want to use.
The channel is selected.
NOTE: Ifyou want to change the transceiver‘s
modulation method, press MODE. Ifthe
mode does not change, there is only one mode
for the channel.
NOTE: Ifyou have an automatic antenna tuner fitted,
press PTT to tune the antenna to the currently
selected channel.
J Do any ofthe following:
- Hold OK to edit the channel, ifpermitted.
- Press OK to search for a channel.
- Press CALL to start a call.
- Hold CALL to go to Contacts.
SENYRv-HW TRANSCEIVER DPERATOR GUIDE 31
OPERATING THE TRANSCEIVER
SELEchNG A CHANNEL FROM A CHANNEL GROUP
Selecting a channel from a channel
group
Ifchannel grouping is enabled in Settings > Control Point >
Channel Grouping and you have allocated channels to groups,
indicated by after a channel group name or in front ofthe channel
name, you may have to switch to another channel group to find the
channel that you want to select.
NOTE: Any channels that are not assigned to a channel
group appear at the top level with the channel group
names. These channels are selected by scrolling to
the channel.
NOTE: You can set the name ofthe current channel group to
show in a status area of the channel screen.
To select a channel from a channel group:
3 Press PTT to exit to the channel or scanning screen.
:I Ifthe transceiver is scanning, press SCAN to switch off
scanning.
Channel group level
and ungmuped channels cnannel level (wlthin a gmup)
Hi 5
Groupi... ...CH 01
10,000 10,000
14:15:48 14:16:02 0
channel group name
J Ifyou are at the channel group level, which may include
ungrouped channels, press A or v to scroll to the channel
32 SENTRV-H W TRANSCEIVER OPERATOR GUIDE
OPERAIING THE TRANSCEIVER
SELECTING A CHANNEL mom A CHANNEL GROUP
group that you want, then press # to view the channels
within that group.
: Ifyou are within a channel group but the channel that you
want is not visible, do one of the following:
- Press # to move to the channel group level,press A
or v to scroll to the channel group that you want,
then press #.
' S
Group 1...
10,000
‘l 4:1 5:48
- Hold # to see a list ofchannel groups, press A
or v to scroll to the channel group that you want,
then press \— (Select).
Select Group
3 Press A or v to scroll to the channel that you want to use.
The channel is selected.
NOTE: Ifyou want to change the transceiver‘s
modulation method, press MODE. Ifthe
mode does not change, there is only one mode
for the channel.
NOTE: Ifyou have an automatic antenna tuner fitted,
press PTT to tune the antenna to the currently
selected channel.
SEva-Hm TRANSCEIVER OPERATOR GUIDE 33
OPERATING THE TRANSCEIVER
SELECTlNG A CHANNEL FROM A CHANNEL GROUP
2| Do any ofIhc following:
- Hold OK l0 edit (11:: channel, if pcrmincd.
- Prcss 0K to Search for II Channel.
- Prcss CALL Io man a call.
- Hold CALL to go to Commas.
34 SENTIw-Hw TRANSCEIVER OPERATOR GUIDE
OPERATING THE TRANSCEIVER
SCANNING CHANNELS
Scanning channels
Ifyou intend to receive calls on several channels, switch on
scanning. When scanning is switched on, the transceiver
sequentially selects each channel/mode in your scan tables to detect
incoming calls. The channels are scanned in a continuous cycle. By
default, mute is switched on automatically when scanning is
switched on.
NOTE: Only those scan tables that are set to be scanned have
the channels scanned. Up to 100 channels may be
scanned.
By default, when the transceiver detects a call addressed to your
station, it stops scanning and notifies you according to the type of
call received. When you press .7. to end the call, scanning
resumes. If you do not press this key to end the call, or any other
key within a pre-detennined timeout, the transceiver automatically
ends the call and resumes scanning.
NOTE: The default standby state for the transceiver is to
return to scanning so that it is ready to receive calls
across a range of frequencies.
When the transceiver detects a signal, it notifies you according to
the mute setting selected. Ifyour transceiver is set to notify you
when voice is detected (V), you can pause scanning, select the
channel/mode on which the voice was heard, then resume scanning
when required. Voice mute also detects calls that are addressed to
any station on the scanned frequency, and any other channel
disturbances. If your transceiver is set to selcall mute (S), it only
pauses scanning when it detects a call addressed to your station,
regardless ofthe call system used.
Your choice ofvoice or selcall mute depends on whether or not you
have to detect voice signals, and how much noise and traffic you
want to hear.
It is recommended that scanning is switched on when you are not
using the transceiver to communicate so that you are able to receive
calls on any frequency in the scanned scan tables.
SENYRV-HW TRANSCEIVER DPERATOR GUIDE 35
OPERATING THE TRANSCEIVER
SCANNING CHANNELS
Switching scanning on or off
To switch scanning on or off:
:I Press SCAN.
lfa call is not in progress, scanning is toggled on or off.
lfa call is in progress, the call is ended and the transceiver
begins scanning.
lfa call from a modem [or any other peripheral device) is in
progress, you are prompted to break the system lock to
resume scanning.
NOTE: When scanning is switched on, mute is also
switched on.
NOTE: lfyou press PTT while the transceiver is
scanning, the scan is stopped.
Pausing scanning
To pause scanning:
3 Do one ofthe following:
- To pause scanning on the last-selected channel,
press OK.
- To pause scanning and scroll to another channel,
press A or V.
The channel/modes through which you can scroll are those
in the scan tables that are being scanned. They are not listed
alphabetically but in the order in which they are being
scanned.
If you do not press a key within 30 sec, the transceiver
automatically resumes scanning, by default.
36 SENTrw-Hw TRANSCEIVER OPERATOR GUIDE
OPERATING THE TRANSCEIVER
SCANNING CHANNELS
2| While scanning is paused, do one ofrhe following:
- To speak on (he selected channel, hold down PTT.
- To resume scanning immedialely, press OK.
- To srop scanning complelely, press SCAN.
SENTRV-Hw TRANSCEIVER OPERATOR GUIDE 37
OPERATING THE TRANSCEIVER
MuTING THE TRANSCEIVER
Muting the transceiver
When the transceiver is set to a channel or is scanning channels,
and mute is switched off, you hear on-air signals on each channel.
Ifyou do not want to listen to this, you can silence the transceiver
by switching on mute.
You can set the mute to switch offwhen a voice signal or any other
calling activity is detected [voice mute V), or only when a call
addressed to your station is received (selcall mute 5). Your choice
of voice or selcall mute depends on whether or not you have to
detect voice signals, and how much noise and traffic you want to
hear. When digital voice is active and scanning is switched off or
paused, you can also set the mute to switch off only when a secure
or clear digital voice signal is detected (digital voice mute D). The
voice signal is output to the speaker ofthe 2320 handset and the
11-250 speaker connected to the RF Unit, if available.
Switching mute on or off
To switch mute on or off:
:I On the 2320 IIandset, pres ‘__ (Mute) on the channel
screen, scanning screen, or free-tune screens
Selecting the mute type
To select the mute type:
J On the 2320 IIandset, press 7lVlS to toggle the mute type
between selcall mute (S) and voice mute (V).
NOTE: When digital voice is active and scanning is switched
offor paused, an additional digital voice mute (D) is
available.
33
SENTRv-Hw TRANSCEIVER OPERATOR GUIDE

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Warning                         : Info object (297 0 obj) not found at 3183438

EXIF Metadata provided by EXIF.tools