Coleman 2000001597 Users Manual Weathermaster 6 Screened Tent

2000001597 to the manual 0296bf8b-d15d-4307-9310-a7c9b92f0e1c

2015-02-04

: Coleman Coleman-2000001597-Users-Manual-365347 coleman-2000001597-users-manual-365347 coleman pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadColeman Coleman-2000001597-Users-Manual- Weathermaster 6 Screened Tent 2000001597  Coleman-2000001597-users-manual
Open PDF In BrowserView PDF
WEATHERMASTER 6 SCREENED TENT
®

MODEL 2000001597

Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.

6. Rotate all eight Leg Poles upright and insert
pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)

7A
Pin

Pole Descriptions
Description

Qty.

Long Leg Pole, steel
(w/ red marking)
4
Short Leg Pole, steel
4
Curved Ridge Pole, steel
(w/ red marking)
2
Curved Ridge Pole, steel 2
Awning Pole, black,
fiberglass, metal tips
1
Door Pole, long, thin, black,
fiberglass, rubber tips
1
Vert. Door Pole, short, black,
fiberglass, rubber tips
1

Pole
Dia.

Pole
Pole
Repair Kit Replacement Kit

19mm
19mm

N/A
N/A

5010000608
5010000610

19mm
19mm

N/A
N/A

5010000607
5010000609

6.3mm 5010000543

5010000545

6.3mm 5010000543

5010000545

6.3mm 5010000543

5010000545

To Set Up Tent

STITCH LINE

1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1

Fig. 7

7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg
Poles to attach. (Fig. 8)
Fig. 8

8. To stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
• Pull up on top Leg Pole section
until tent is taut;
• Twist the lower Leg Pole clockwise until the button locks into
the center or lowest hole;
• Repeat on remaining Leg Poles.

Fig. 9
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section

9. Insert plastic stakes through web
straps located on both sides of tent,
then drive in to secure. (Fig. 10)
NOTE: It may be necessary to remove
metal stakes through web straps at
side of tent and screen room, pull tent
taut, and drive in stakes to secure.

Door

2. Pull four corners of tent taut, then secure by
driving stakes through web loops at an angle
for better anchoring. (Fig. 2)
Fig. 2

3. Assemble four, steel, shock-corded,
Fig. 3
Ridge Pole
curved Ridge Poles. Insert Ridge Poles
with Red
Marking
(with red marking) into center sleeves
on top of tent with the red trim (Fig. 3).
Sleeve
Insert the remaining curved Ridge Poles
with Red
Trim
into the other two sleeves on top of tent.
4. Assemble eight, steel, shock-corded, Leg Poles. Push down
on steel button on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)
Button in third hole
5. Insert curved end of Leg Poles
Fig. 4
(with red marking) into the ends of the
Ridge Poles (with red
Ridge Pole with
marking). Insert curved
Red Marking
end of remaining short
Leg Poles into the ends
of the remaining Ridge
Sleeve
Curved End of
with Red
Poles. (Fig. 5 & 6)
Long Leg Pole
Trim

Fig. 10

Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic
cap tips); then insert through zippered vertical pole sleeveon
hinged side of door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate,
apply pressure to form a slight bow, then insert other tip of
pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips);
then insert into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure
to form a bow, then insert other tip of pole into the bottom
hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11

Fig. 12

Fig. 13

Vertical Pole
Sleeve

Door Hinge

Fig. 5

Fig. 6
Curved Ridge
Poles with Red
Marking in
center 2
sleeves

Fig. 14
Top
Door
Hinge

Fig. 15

Pole
Sleeve

Fig. 16

(continued on other side)

To Attach Rainfly

Electrical Cord Access

1. Drape Rainfly over tent. Make sure seams on Rainfly are
facing down and centered over poles of the tent. (Fig. 11)
NOTE: Hook and loop fasteners, located on seams of under side of Rainfly, should be centered over Ridge Poles.

1. Unzip access panel in the lower
left corner of tent and bring in
electrical cord.
NOTE: Use only UL approved cords
rated for outdoor usage. (Fig. 20)

Fig. 11

Rainfly

Fig. 20

Cooler Access
Sleeve
Door

2. Assemble thin, black, shockcorded Awning Pole with metal
tips; then insert through sleeve
in Rainfly above door. (Fig. 12)

Awning
Pole

Fig. 12

Sleeve

6. Insert metal hook
on elastic straps on
Rainfly into the hole
on each Leg Pole.
(Fig. 15 & 16)

Fig. 21

Fig. 22

Door & Window Flaps/Vents
1. For better ventilation, unzip door flaps, roll, and insert
toggle into fabric loop to secure.
2. To open back and side window vents for more ventilation,
unzip, then roll up and insert toggles through fabric loops.

To Store
1. All poles and stakes must be placed in the storage bag to
prevent damage to the fabric items placed in the carry case.
2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip
door & vents before taking tent down for storage.
4. Neatly fold tent to width of pole storage bag, place on tent,
roll tightly, and place in carry case.
5. Store in a clean, dry area.

Things You Should Know:

Center
Leg Pole
Location
End Leg
Pole
Location

Fig. 16

Fig. 15

7. Loop ends of guylines over stakes, stretch tight,
then hammer into ground at an angle as
shown. (Fig. 17 & 17A)
Fig. 17
17A
Guyline

• Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside of your tent. Condensation is caused by water
vapor from your breath, perspiration, or any wet clothing inside the tent.
It is NOT LEAKAGE through the tent fabric. It can be minimized by
removing wet clothing from your tent and by providing good ventilation through the tent.
• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off
tree limbs can cause damage to the tent fabric and its coating resulting
in leaks or loss of flame-resistant properties.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. NEVER PULL ON
THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
• Tent poles should not be left telescoped together during storage.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.

WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.

Attaching Room Divider
1. Divider Panel can be installed through
center of the tent by inserting toggles
through the top and bottom fabric
loops as shown.
(Fig. 18 & 19)

Top
Fabric
Loops

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2008 The Coleman Company, Inc.

Divider
Panel

Fig. 18

Coleman®,

Fig. 19

,

, and Weathermaster® are registered trademarks of
The Coleman Company, Inc.
4010004005 (20081030)

STITCH LINE

3. Insert tapered metal tip on
Grommet
Awning Pole into grommet
Awning Pole
located on web strap clipped to
center Leg Pole. (Fig. 13)
4. Go to opposite center Leg Pole
on other side of door and
Fig. 13
gradually apply pressure to the
pole forming an arch. Insert metal tip into the grommet.
5. Locate all hook & loop fasteners on
Fig. 14
underside of Rainfly and wrap around
Leg Poles and Awning Pole locations.
(Fig. 14)

The smaller zippered opening at the back
of tent is designed for added ventilation
and easy access to your beverage cooler.
1. To use as a vent, unzip flap to expose
screen. (Fig. 21)
2. To use as a cooler access, unzip
other flap to make an avenue to bring
beverages into tent. (Fig. 22)



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Keywords                        : Manuals
Modify Date                     : 2009:03:11 09:03-05:00
Creator Tool                    : QuarkXPress: pictwpstops filter 1.0
Create Date                     : 2009:03:11 09:02:32-05:00
Metadata Date                   : 2009:03:11 09:03-05:00
Format                          : application/pdf
Creator                         : Weathermaster 6 Screened Tent 2000001597
Title                           : Weathermaster 6 Screened Tent 2000001597
Description                     : PDF
Subject                         : Manuals
Document ID                     : uuid:72d35270-6503-484b-811d-ade40cacea79
Instance ID                     : uuid:b090300b-d56a-4777-9912-7fe217a35e02
Page Count                      : 2
Author                          : Weathermaster 6 Screened Tent 2000001597
Warning                         : [Minor] Ignored duplicate Info dictionary
EXIF Metadata provided by EXIF.tools

Navigation menu