Coleman 2000001597 Users Manual Weathermaster 6 Screened Tent

2000001597 to the manual 0296bf8b-d15d-4307-9310-a7c9b92f0e1c

: Coleman Coleman-2000001597-Users-Manual-365347 coleman-2000001597-users-manual-365347 coleman pdf

Open the PDF directly: View PDF .
Page Count: 2

STITCH LINE

6. Rotate all eight Leg Poles upright and insert

pin on each web loop at the side locations

as shown. (Fig. 7 & 7A)

(continued on other side)

Fig. 6

Fig. 7

7A

Pin

7. Locate the plastic hooks at sides and

corners of tent, then snap onto Leg

Poles to attach. (Fig. 8)

9. Insert plastic stakes through web

straps located on both sides of tent,

then drive in to secure. (Fig. 10)

NOTE: It may be necessary to remove

metal stakes through web straps at

side of tent and screen room, pull tent

taut, and drive in stakes to secure. Fig. 10

8. To stretch tent to finished size:

• Push in button on Leg Pole while

twisting lower Leg Pole section

counterclockwise (Fig.9);

• Pull up on top Leg Pole section

until tent is taut;

• Twist the lower Leg Pole clock-

wise until the button locks into

the center or lowest hole;

• Repeat on remaining Leg Poles.

Fig. 8

Fig. 9

Button

Center Hole

Lower Hole

Lower

Leg Pole

Section

Upper

Leg Pole

Section

WEATHERMASTER® 6 SCREENED TENT

MODEL 2000001597

Curved Ridge

Poles with Red

Marking in

center 2

sleeves

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic

cap tips); then insert through zippered vertical pole sleeveon

hinged side of door. (Fig. 11)

2. Insert end of Vertical Door Pole into bottom hinge plate,

apply pressure to form a slight bow, then insert other tip of

pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3. Assemble Door Pole (longer black pole with plastic cap tips);

then insert into zippered pole sleeve at top of door. (Fig. 14)

4. Insert end of Door Pole into top hinge plate, apply pressure

to form a bow, then insert other tip of pole into the bottom

hinge. (Fig. 15)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Fig. 1

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the

door facing the desired direction. Unzip doors. (Fig. 1)

4. Assemble eight, steel, shock-corded, Leg Poles. Push down

on steel button on tapered end and insert into end with

four holes.

NOTE: Make sure steel button locks

into third hole on pole as shown. (Fig.4)

5. Insert curved end of Leg Poles

(with red marking) into the ends of the

Ridge Poles (with red

marking). Insert curved

end of remaining short

Leg Poles into the ends

of the remaining Ridge

Poles. (Fig. 5 & 6)

Door

Ridge Pole with

Red Marking

Button in third hole

Fig. 4

Fig. 5

Fig. 2

Sleeve

with Red

Trim

Curved End of

Long Leg Pole

2. Pull four corners of tent taut, then secure by

driving stakes through web loops at an angle

for better anchoring. (Fig. 2)

Ridge Pole

with Red

Marking

Fig. 3

Sleeve

with Red

Trim

3. Assemble four, steel, shock-corded,

curved Ridge Poles. Insert Ridge Poles

(with red marking) into center sleeves

on top of tent with the red trim (Fig. 3).

Insert the remaining curved Ridge Poles

into the other two sleeves on top of tent.

Pole Descriptions

Pole Pole Pole

Description Qty. Dia. Repair Kit Replacement Kit

Long Leg Pole, steel

(w/ red marking) 4 19mm N/A 5010000608

Short Leg Pole, steel 4 19mm N/A 5010000610

Curved Ridge Pole, steel

(w/ red marking) 2 19mm N/A 5010000607

Curved Ridge Pole, steel 2 19mm N/A 5010000609

Awning Pole, black,

fiberglass, metal tips 1 6.3mm 5010000543 5010000545

Door Pole, long, thin, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Vert. Door Pole, short, black,

fiberglass, rubber tips 1 6.3mm 5010000543 5010000545

Fig. 11 Fig. 12 Fig. 13

Fig. 14 Fig. 15

Fig. 16

Vertical Pole

Sleeve

Door Hinge

Pole

Sleeve

Top

Door

Hinge Pole

Sleeve

Top

Door

Hinge

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp

objects, to install your tent.

WARNING: Keep clear of overhead power lines.

• Do not set up your tent under trees because of potential lightning strikes

or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent property damage

or personal injury.

• For best results in windy conditions, position narrow end of tent into

the wind.

• Enlist the help of at least one other person to assist you when it is time

to assemble the tent.

3. Insert tapered metal tip on

Awning Pole into grommet

located on web strap clipped to

center Leg Pole. (Fig. 13)

4. Go to opposite center Leg Pole

on other side of door and

gradually apply pressure to the

pole forming an arch. Insert metal tip into the grommet.

5. Locate all hook & loop fasteners on

underside of Rainfly and wrap around

Leg Poles and Awning Pole locations.

(Fig. 14)

STITCH LINE

Attaching Room Divider

1. Divider Panel can be installed through

center of the tent by inserting toggles

through the top and bottom fabric

loops as shown.

(Fig. 18 & 19)

To Store

1. All poles and stakes must be placed in the storage bag to

prevent damage to the fabric items placed in the carry case.

2. Make sure tent is clean and dry before placing in carry case.

3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole storage bag, place on tent,

roll tightly, and place in carry case.

5. Store in a clean, dry area.

Fig. 18

Fig. 16

Fig. 14

Fig. 17

Fig. 13

Grommet

End Leg

Pole

Location

7. Loop ends of guylines over stakes, stretch tight,

then hammer into ground at an angle as

shown. (Fig. 17 & 17A)

Awning Pole

To Attach Rainfly

1. Drape Rainfly over tent. Make sure seams on Rainfly are

facing down and centered over poles of the tent. (Fig. 11)

NOTE: Hook and loop fasteners, located on seams of under -

side of Rainfly, should be centered over Ridge Poles.

Fig. 11

Rainfly

Door

Sleeve

Fig. 12

2. Assemble thin, black, shock-

corded Awning Pole with metal

tips; then insert through sleeve

in Rainfly above door. (Fig. 12)

Awning

Pole

Sleeve

Fig. 19

Divider

Panel

Top

Fabric

Loops

Fig. 15

Center

Leg Pole

Location

17A

Guyline

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

© 2008 The Coleman Company, Inc.

Coleman®, , , and Weathermaster®are registered trademarks of

The Coleman Company, Inc.

4010004005 (20081030)

6. Insert metal hook

on elastic straps on

Rainfly into the hole

on each Leg Pole.

(Fig. 15 & 16)

Cooler Access

The smaller zippered opening at the back

of tent is designed for added ventilation

and easy access to your beverage cooler.

1. To use as a vent, unzip flap to expose

screen. (Fig. 21)

2. To use as a cooler access, unzip

other flap to make an avenue to bring

beverages into tent. (Fig. 22)

Electrical Cord Access

1. Unzip access panel in the lower

left corner of tent and bring in

electrical cord.

NOTE: Use only UL approved cords

rated for outdoor usage. (Fig. 20)

Fig. 22

Fig. 21

Door & Window Flaps/Vents

1. For better ventilation, unzip door flaps, roll, and insert

toggle into fabric loop to secure.

2. To open back and side window vents for more ventilation,

unzip, then roll up and insert toggles through fabric loops.

Fig. 20

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water

vapor from your breath, perspiration, or any wet clothing inside the tent.

It is NOT LEAKAGE through the tent fabric. It can be minimized by

removing wet clothing from your tent and by providing good ventila-

tion through the tent.

• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off

tree limbs can cause damage to the tent fabric and its coating resulting

in leaks or loss of flame-resistant properties.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles

inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. NEVER PULL ON

THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

• Tent poles should not be left telescoped together during storage.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or

cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The

fabric may burn if left in continuous contact with any flame source.

The application of any foreign substance to the tent fabric may

render the flame-resistant properties ineffective.