Comeup 881102 WIRELESS REMOTE CONTROL User Manual

Comeup Industries Inc. WIRELESS REMOTE CONTROL Users Manual

Users Manual

Download: Comeup 881102 WIRELESS REMOTE CONTROL User Manual
Mirror Download [FCC.gov]Comeup 881102 WIRELESS REMOTE CONTROL User Manual
Document ID1265596
Application IDEvK4qEiJt3qYpN6tK8L36g==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize89.17kB (1114579 bits)
Date Submitted2010-04-13 00:00:00
Date Available2010-04-15 00:00:00
Creation Date2010-03-17 12:06:23
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2010-04-13 09:15:50
Document TitleUsers Manual
Document CreatorAcrobat PDFMaker 8.1 for Word
Document Author: SuperXP

INSTALLATION GUIDE
Part No.881262
RF-24 Wireless Remote Control
1.
2.
For Automotive Winches
Wireless Control Kit includes:
1. Wireless Receiver.881103
2. Switch Cord W/6P plugs Ø8 X 1500 mm
3.
4.
5.
3. Wireless Transmitter.881102
4. Lithium Battery: 3V CR2032
5. Handsaver Strap
I.Specifications
1. Transmission range:15 ~ 27 m (50 ~ 90 ft)
2. Receiver operation voltage: 8 ~ 24 V
3. Receiver fuse current rating: 7.5 A
4. Protection: IP-66
5. Operating Temperature Range: -20°C ~ +70°C
II.Installation Guide
Step 1: Connect the wiring
a. Connect the Switch cord W/6P plugs to the socket on the control pack.
b. Slice the Red wire to the receiver fuse then connect to the positive (+) terminal of the
battery.
c. Connect the Black wire to the negative (-) terminal of the battery.
Step 2: Mount the Receiver
a. The receiver should be mounted in a clear and dry location.
b. Mount on a flat surface with 2 pieces of Ø7 mm mounting
holes on each side of the receiver.
Minimum of one mounting hole each side
III Operation
1. Install and replace battery.
a. Remove the three screws from the wireless transmitter.
b. Separate the top section and remove the old battery and dispose it.
c. Insert new battery and join the top section with the bottom section.
d. Make sure to fasten the three screws.
Lithium Battery: CR2032 (3V)
2. Start
a. Turn on the Vehicle.
b. Press the Power Buttons for 5 seconds until Green light comes on.
c. Press the Cable In or Cable Out button after the Red light comes on.
LED Indicator
Cable OUT
Power Button
Cable IN
Cable IN
Cable OUT
3. Stop
a. The system will be automatically shutting down the operation after a silence of
operation for 5 minutes.
b. Press and hold the Power Button for 5 seconds for
shutting down the operation.
4. Reset
a. Press and hold the Programming Button for 5 seconds until the Red lights up。
b. Press the Power Buttons for 5 seconds until the Red flashing.
c. Press the Cable In or Out button until the Red lights on the receiver turns off.
d. Reset is now completed. Please note only one remote can be reset for each receiver.
5. Notes
a. The wireless remote control and handlebar trigger switch can be exchanged for
activating the winch, but it takes about 10 seconds for exchanging。
b. The flashing Red light shows batter low, the battery should be replaced immediately.
c. Please note only one remote can be reset for each receiver
FCC and Industry Canada (IC) Warning:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
FEDERAL
COMMUNICATIONS
RF
exposure
warning COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
The
equipment
complies
FCC
RFand,
exposure
limits
set inforth
for an
generates,
uses and can
radiate radiowith
frequency
energy
if not installed
and used
accordance
withuncontrolled
the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
environment.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off andequipment
on, the user is encouraged
try toco-located
correct the interference
by one or more
of the following measures:
The
must nottobe
or operating
in conjunction
with any other antenna
-Reorient or relocate the receiving antenna.
or
transmitter.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the
equipment.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Company                         : CMT
Source Modified                 : D:20100317040550
Create Date                     : 2010:03:17 12:06:23+08:00
Creator Tool                    : Acrobat PDFMaker 8.1 for Word
Modify Date                     : 2010:04:13 09:15:50-04:00
Metadata Date                   : 2010:04:13 09:15:50-04:00
Document ID                     : uuid:bedef4f0-9543-40d8-a49f-e3aade92b4b6
Instance ID                     : uuid:b0a8f9b2-da55-450e-9188-1ef4765b0d32
Subject                         : 2
Format                          : application/pdf
Creator                         : SuperXP
Title                           : 
Has XFA                         : No
Page Count                      : 2
Page Layout                     : OneColumn
Author                          : SuperXP
EXIF Metadata provided by EXIF.tools
FCC ID Filing: X96881102

Navigation menu