Comeup ICB Wireless Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3965591
Application ID	jP09kDCpQR0flGzX2To2Fw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	37.75kB (471836 bits)
Date Submitted	2018-08-16 00:00:00
Date Available	2018-08-17 00:00:00
Creation Date	2018-08-10 15:16:21
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-08-10 15:16:21
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	alexlin

Intelligent Control Box
Model: ICB
 INDEX：
I. Introduction
II. Contents
III. Installation
IV. ICB Information Panel
V. Operating Instructions
VI. Warning
III. Installations：
• Connect power cables F1, F2, and A to the motor terminal studs, guided
by the color markings.
• Connect power cable B(-) and ground cable to the stud located on the
bottom of the motor.
• Connect the thermal sensor cable to both the control box and the motor.
• Mount ICB unit on the motor support rack bracket.
• Connect power cables A(+) and B(-) to battery terminals.
I. Introduction：
• The Intelligent Control Box (ICB) is COMEUP latest product, designed to
allow adjustment of a winch’s maximum pulling power.
• A built-in, adjustable current limiter detects the motor amp draw and will
interrupt the power if the current exceeds the current limit point (CLP).
The CLP can be adjusted using the Current Regulator (sold separately).
Regarding CLP setup process, please refer to Current Regulator user
manual.
• An embedded information panel provides vehicle battery, winch cable
in/out operation, winch over heating and overload information.
F1
II. Contents：
F2
• Intelligent Control Box
• Handheld Remote
BLACK(-)
(-)
(BLUE)
(YELLOW)
(GROUND CABLE)
(WHITE)
○
(ICB)
○
(BATTERY)
BLACK(-)
RED(+)
(THERMAL SENSOR)
-1-
-2-
VI. Warning：
IV. ICB Information Panel：
• Unplug the wired remote control after use to prevent battery power
• Information Panel：
V. Operating Instructions：
Item
Icom
Features
Instructions
 Battery voltage above 12V.
 Battery voltage between 11V and 12V.
Winch
Operation
Indicator
Overheat
Indicator
Overload
Indicator
 Battery voltage between 10V and 11V.
Vehicle
Battery
Monitor
Wireless
Connection
Indicator
 Battery voltage between 9V and 10V.
 Battery voltage between 8V and 9V.
 When battery voltage is lower than 8V, the
red light begins blinking and the buzzer
alarms.
 During winch cable-in operation, the winch
operation indicator bar scrolls outside-in.
 During winch cable-out operation, the winch
operation indicator bar scrolls inside-out.
 When the thermal sensor detects winch
motor overheating (over 100 degrees
Celsius), Overheat indicator blinks with
buzzer alarm.
 The winch operation indicator turns red
when the winch is operated.
 When the ICB detects winch overload,
Overload protection mode is automatically
activated, the Overload Indicator blinks for
30 seconds, the buzzer alarm sounds for the
first 5 and last 5 seconds.
 During Overload protection mode, Cable-in
operation is disabled, Cable-out operation
remains functional.
 After 30 seconds of automatic Overload
protection mode, the Overload icon will turn
off and the winch will return to normal
operation mode.
 The Indicator blinks for 10 secends.
 Pairing within 10 seconds.
-3-
consumption and accidental damage to the remote or winch.
• To use the wireless transmitter, the wired remote control must be
connected.
• To prevent electrical component damage, disconnect the control box from
the power source during internal inspection or repair.
• To prevent damage, do not connect other USB devices to USB port on
ICB unit.
• To prevent damage, do not connect the Current Regulator to any USB
devices other than the ICB unit.
 Wireless Receiver & Transmitter Operation
This wireless remote control device complies with CE mark, FCC and Industry Canada (IC) rules.
CE Mark Warning
• This is a Class B product, in a domestic environment, this product may cause radio
interference, In which case the user may be required to take adequate measures.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
-4-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : alexlin
Create Date                     : 2018:08:10 15:16:21+08:00
Modify Date                     : 2018:08:10 15:16:21+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : <4D6963726F736F667420576F7264202D20494342B971B1B1B2D5BEDEA740BBA1A9FAAED12D5231>
Creator                         : alexlin
Document ID                     : uuid:82f55e8d-d179-4e6a-9494-28157bfeb5ff
Instance ID                     : uuid:06ca1d47-e67d-4da1-a5d4-8e1b4d8935f7
Page Count                      : 2

EXIF Metadata provided by EXIF.tools