Compex Systems 06-WLM54AGP23 Wireless-AG 23dBm Network Mini PCI Adapter User Manual

Compex Systems Pte Ltd Wireless-AG 23dBm Network Mini PCI Adapter Users Manual

Users Manual

*****Caution***** Changes or modifications not expressly approved by the party responsible for the compliance could void the user’s authority to operate the equipment. ***** FCC Statements***** This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use), and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: "Contains ". Manual Information for End Users The end user must not have manual instructions to remove or install the device. The user manual for end users must include the following information in a prominent location. "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."
Quick Install GuideCompexWireless-AG 23 dBm NetworkMini PCI AdapterWLM54AGP23Version 1.1 1. IntroductionThis mini PCI adapter, Compex WLM54AGP23 contains a dual-modesingle chip MAC/BB/Radio for IEEE 802.11a, 11g and 11b WirelessLAN. It can support high-speed data transmission of up to 54Mbps inthe 2.4GHz and 5GHz frequency bands based on 802.11b/g and802.11a mode respectively. Based on the latest industry standard Wi-Fi Certified IEEE802.11a/b/g specification, the Compex WLM54AGP23 offers maximumchannel speeds of up to 54 Mbps. It supports key security featureslike Wi-Fi Protected Access (WPA), WPA2, WEP and 802.1x. You can find this adapter that is seated inside the wireless productssuch as the WPE54AG. WLM54AG can be removed from or insertedonto the PCBA of the WPE54AG.2. Package ContentCompex WPE54AG retail package contains the following items:•1 x Compex WPE54AG•1 x External Power Adapter•1 x 3dBi SMA Antenna•1 x Base Stand•1 x RJ45 MDIX cross-over Ethernet cable•1 x Quick Install Guide with Warranty Registration Form•1 x Product CD (including Quick Install Guide, User’s Manual,Firmware Recovery Tool & Utilities)3. Hardware Installation1. Connect one end of the RJ45 crossover Ethernet cable to yourPC and another end to the Ethernet port of your CompexWPE54AG.2. Next, attach the power adapter supplied in the packaging to thepower point.3. Connect the power plug onto the socket on your CompexWPE54AG.4. Power ON your Compex WPE54AG and your PC. Notice thatthe LAN Link/ACT and Power LEDs have lighted up. Thisindicates that the connection has established successfullybetween your Compex WPE54AG and your PC.NETPASSAGEPCPower PointRJ45Ethernet cableCompexWPE54AG
4. Access to Web-based InterfaceCompex has developed a powerful uConfig utility which providesyou hassle-free access to the web-based configuration page. To do so,simply1. Insert your Product CD into your CD-ROM drive. Go toUtilities section and select uConfig to run the program.2. The following screen shot will appear. Select NetPassageWPE54AG and click on OpenWeb button to access to theauthentication page.3. The password is pre-configured as password in the fieldprovided. Click on Log On! button to access to the main page.After accessing to the main page of your Compex WPE54AG, youcan start doing your configuration5. Basic Configuration for Compex WPE54AG1. To handle automatic IP addressing, go to Management Portunder CONFIGURATION section.2. Go to DHCP Server option and select Enable radio button.Click on Apply button to update the changes.Now, your Compex WPE54AG acts as a DHCP Server which canassign IP address to your PC/clients.6. WLAN Basic Setup for Compex WPE54AG1. To configure your Compex WPE54AG for your wireless user,go to WLAN Basic Setup from the CONFIGURATIONsection.2. From your Access Point Setup window, key in the ESSID thatyou intend to use for your wireless network.3. You may leave the frequency channel as SmartSelect. Thisallows your access point to select the channel automatically.4. Leave the remaining settings as default and click Apply buttonto update the changes.7. TCP/IP Configuration for wireless clientsGenerally, automatic IP addressing should be configured for yourwireless client PCs or notebooks. You may configure the TCP/IPsettings of Microsoft windows XP as follows:1. From your desktop, right click on My Network Places andselect Properties.2. Next, right click on your Ethernet Adapter go to Properties.3. Highlight Internet Protocol (TCP/IP) and click on Propertiesbutton.
4. Select the radio buttons for Obtain an IP addressautomatically and Obtain DNS server address automatically.Click OK button to update the changes.Next, you may set up Windows XP’s Wireless Network Connectionas follows:5. Right click on WirelessNetwork Connectioncorresponding to the WirelessEthernet Adapter you wish toconnect to your CompexWPE54AG, and click onProperties.6. Go to Wireless Networks tab and click on Add.. button.7. Next, enter the Network name (SSID) which must be the sameas the ESSID that you input earlier for your access point.Ensure that the Network name (SSID) value is the same for allwireless clients in the same wireless network.For now, you may leave the other information as its default settings.Network Authentication: OpenData encryption: DisabledFor details in configuring your Compex WPE54AG, kindly refer tothe User’s Manual stored in the Product CD.
8. Panel Views and DescriptionsFeatures Status and Indications1 LAN Link/ActLED Steady Yellow Compex WPE54AG isoperating at the speedof 10Mbps.Steady Green Compex WPE54AG isoperating at the speedof 100Mbps.2 WLAN Link/ActLED Steady Green More than 1 wirelessclient is present in thewireless network.Blinking Green Activity is detected inthe wireless network.3 Diagnostic LED Steady Green The device is in accesspoint or gateway mode.Blinking Green The device is booting.Off The device is in Clientmode.4 Power LED Steady Blue Power is supplied to thedevice.Off No power is supplied tothe device.5 External Antenna Rotatable antenna6 LAN RJ45Ethernet Port Using RJ45 Ethernet cable for connection.7 DC 3.3V 3A Power input of 3.3VDC8 Reset button Push button:2s to reboot your devicebetween 2s to 10s to restore to itsfactory default> 10s for operating mode switchThis document may become superseded, in which case you may findits latest version at:http://www.compex.com.sg/prodspec.asp?f=Manual&s=1Disclaimer: Compex, Inc. provides this guide without warranty of any kind, either expressed or implied,including but not limited to the implied warranties of merchantability and fitness for a particular purpose.Compex, Inc. may make improvements and/or changes to the product and/or specifications of the productdescribed in this guide, without prior notice. Compex, Inc will not be liable for any technical inaccuracies ortypographical errors found in this guide. Changes are periodically made to the information contained herein andwill be incorporated into later versions of the guide. The information contained is subject to change withoutprior notice.Trademark Information: Compex®, ReadyLINK® and MicroHub® are registered trademarks of Compex,Inc. Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. NetWare is theregistered trademark of Novell Inc. All other brand and product names are trademarks or registered trademarksof their respective owners.Notice: Copyrights © 2004 by Compex, Inc. All rights reserved. Reproduction, adaptation, or translationwithout prior permission of Compex, Inc. is prohibited, except as allowed under the copyright laws.Manual Revision by AnnManual Number: M-0428-V1.2C Version 1.2, April 2005FCC NOTICE: This device has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This device generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis device does cause harmful interference to radio or television reception, the user is encouraged to try tocorrect the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Connect the computer into an outlet on acircuit different from that to which thereceiver is connected.Increase the separation between the computer andreceiver.Consult the dealer or an experienced radio / TVtechnician for help.Caution: Any changes or modifications not expressly approved by the grantee of this device could void theuser's authority to operate the equipment.FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1)(2) This device may not cause harmful interference, andThis device must accept any interference received, including interference that may cause undesiredoperation.Products that contain a radio transmitter are labeled with FCC ID and may also carry the FCC logo.Caution: Exposure to Radio Frequency Radiation.To comply with the FCC RF exposure compliance requirements, the following antenna installation and deviceoperating configurations must be satisfied:a.b.For configurations using the integral antenna, the separation distance between the antenna(s) and anyperson’s body (including hands, wrists, feet and ankles) must be at least 2.5cm (1 inch).For configurations using an approved external antenna, the separation distance between the antenna andany person’s body (including hands, wrists, feet and ankles) must be at least 20cm (8 inch).The transmitter shall not be collocated with other transmitters or antennas.ICES 003 StatementThis Class B digital apparatus complies with Canadian ICES-003.DECLARATION OF CONFORMITY: Compex, Inc. declares that the product:Product Name: Compex Wireless-A/G Dual-Band Network Access PointModel No.: WPE54AG conforms to the following Product Standards:Radiated Emission Standards: ETSI EN 300 328-2: July 2000; FCC: 47 CFR Part 15, Subpart B, ANSIC63.4-1992; 47 CFR Part 15, Subpart C (Section 15.247), ANSI C63.4-1992. Conducted Emission Standards: ETS 300 826: Nov. 1997.Immunity Standards: IEC 801-2; IEC 801-3; IEC 801-4Low Voltage Directive: EN 60 950:1992+A1: 1993+A2: 1993+A3; 1995+A4; 1996+A11: 1997Therefore, this product is in conformity with the following regional standards: FCC Class B – following theprovisions of FCC Part 15 directive; CE Mark – following the provisions of the EC directive.Manufacturer’s Name: Compex, Inc.Address:840 Columbia Street , Suite BBrea, CA 92821, USAWARRANTY REGIS T RATION CARDRegister via the Internet at http://www.cpx.com or http://www.compex.com.sg[M-0088-V2.4C]To activate the warranty, please complete this card and return to Compex within ninety (90) daysfrom the date of purchase.Please e-mail this warranty card to support@compex.com.sg.Product: Purchase Date: Model: Serial No:Name: E-mail:Company:Address:Postal/Zip Code: Country:Phone: ( )Note:For purchases within U.S.A and Canada, please fax to Compex, Inc. at (714) 482 0332For purchases outside U.S.A and Canada, please fax to Compex Systems Pte Ltd at (65) 6280-9947---------Cut along the dotted line----------Cut along the dotted line----------Cut along the dotted line-------------Cut along the dotted line--------Cut along the dotted line------- Cut along the dotted line----------- Cut along the dotted line-----POWER534126 7 8 5

Navigation menu