Compex Systems WLE200NX WIRELESS-ABGN 2X2 NETWORK MINIPCIE ADAPTER User Manual WLE200NX

Compex Systems Pte Ltd WIRELESS-ABGN 2X2 NETWORK MINIPCIE ADAPTER WLE200NX

UserManual.wiki >

Compex Systems >

WLE200NX User Manual

WLE200NX-User Manual

wireless modulesLast Updated: 21/06/16KEY FEATURES• Qualcomm Atheros AR9280• Atheros XB92 Reference Design • Dual-band 2x2 MIMO spatial multiplexing technique • 2.4GHz max 18dBm & 5GHz max 17dBm output power (per chain)• IEEE 802.11n compliant & backward compatible with 802.11b/g• 2x2 MIMO Technology, up to 300Mbps• Mini PCI Express 1.1 interface• Supports WPA2 encryption (IEEE 802.11i) and 802.1X authentication• Supports Transmit Power Control (IEEE 802.11h)• Dynamic Frequency Selection (DFS)• Supports additional regulatory domains (IEEE802.11d)Dual Band 2x2 MIMO 802.11n Mini PCIe Module Designed for Dual Band Wireless Access PointsSpecicationsChipset AR9280Host Interface Mini PCI-Express 1.1 StandardOperating Voltage 3.3V DCAntenna Connector 2x U.FLFrequency Range 2.4GHz: 2.412 ~ 2.484 GHz 5GHz: 5.150 ~ 5.875 GHzCertiﬁcation FCC & CE Certiﬁed, RoHS CompliantPower Consumption 3.7W (Max)Modulation Techniques OFDM: BPSK, QPSK, 16-QAM, 64-QAMTemperature Range(for WLE200NX)Operating: -20ºC to 70ºCStorage: -40ºC to 90ºCIndustrial Grade Temperature Range(for WLE200NX-I)Operating: -40ºC to 70ºCStorage: -40ºC to 90ºCHumidity Operating: 5% to 95% (non-condensing)Storage: Max. 90% (non-condensing)Dimensions (H x W x D) 50.95 x 30 x 3.2 mmModel: WLE200NX / WLE200NX-I

COMPLIANCE INFORMATION FCC NOTICE This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Connect the computer into an outlet on a circuit different from that to which the receiver is connected. • Increase the separation between the computer and receiver. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device must accept any interference received, including interference that may cause undesired operation. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. FCC ID: TK4WLM200NX IMPORTANT NOTE: EQUIPMENT MANUFACTURERS COMPEX FOR DISPLAYING WLM200NX MODULAR FCC ID ON FINAL INTEGRATED

FCC ID: TK4WLM200NX IMPORTANT NOTE: EQUIPMENT MANUFACTURERS COMPEX FOR DISPLAYING WLM200NX MODULAR FCC ID ON FINAL INTEGRATED OEM integration instructions:This device is intended only for OEM integrators under the following conditions：The module is only limited to installation in mobile applications. The antenna must be installedsuch that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with theintegral antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met，further transmitter test will not be required.However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirement with this module installed (for example，digital device emission，PC peripheral requirements，etc.)End product labeling:This transmitter module is authorization only for use in device where the antenna may beinstalled such that 20cm may be maintained between the antenna and users. The final endproduct must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: TK4WLE200NX or Contains FCC ID: TK4WLE200NX ”.

Navigation menu