Compex Systems WPJ342 WIRELESS ACCESS POINT User Manual Ethernet

Compex Systems Pte Ltd WIRELESS ACCESS POINT Ethernet

User Manual

Ethernet 2 FE ports with Auto-MDI/X Extras Serial Port2, JTAG3, Reset Button, Surge Arrestor, Watchdog Timer Power Solutions High voltage DC Jack Input:12-24V, Passive PoE: 36-48V, IEEE 802.3af PoE Low voltage DC Jack Input: 12-24V, Passive PoE: 12-24V PoE Injector Compatibility IEEE 802.3af/at injectors(both end span and mid span) Passive injectors Power consumption (board only) 4W ROHS Compliance Yes Humidity Operating: 5% to 95% (non-condensing) Storage: Max.90% (non-condensing) Temperature Range Operating: -20ºC to 70ºC Storage: -40ºC to 90ºC Dimension 95 X 105 x 18 (mm) SYSTEM INFORMATION Processor Qualcomm-Atheros AR9342 System Memory 64MB DDR2 NOR Flash 8MB (max 16MB optional)1 PCIe Slot 9.2mm height miniPCIe slot Antenna Connector 2 x U.FL 5GHz On-board Radio Transmit Power Data Rate Aggregate Power HT20 MCS0 25dBm HT20 MCS7 19dBm HT40 MCS0 24dBm HT40 MCS7 19dBm Receiver Sensitivity Data Rate 5GHz HT20 MCS0 -94dBm HT20 MCS7 -77dBm HT40 MCS0 -93dBm HT40 MCS7 -75dBm Dual Radio Embedded Board Model: WPJ342 FEATURES  CompexWRT and OpenWRT firmware supported  Qualcomm-Atheros 560MHz Networking Processor  Dual Radio Solution (one 2x2 11n 5Ghz on-board radio and one miniPCIe slot that supports all Compex 802.11n WLE series)  Integrated Passive PoE (alternative 802.3af PoE available)  Support 2 x FE Port APPLICATIONS  Dual Band, Dual Concurrent AP  802.11a/n+802.11b/g/n AP  Point to Point / Point to MultiPoint  Base Station  CPE TECHNICAL SPECIFICATION
ORDERING INFORMATION Item Code Version Processor L/H voltage Power Solutions NOR Flash Memory Socket Height WPJ342HV 7A05PCW864AR Compex-WRT AR9342 High Voltage (48V) 8MB 64MB 9.2mm WPJ342LV 7A05PCW864AR AR9342 Low Voltage (24V) 1 Depends on Order Configurations 2 Serial Port is a 4-pin header (TTL) + Serial Converter is available to change the TTL signals on board to RS232 signals for debugging. Configurations are subjec to change without notification. 3 JTAG Port is a 14-pin header + JTAG kit is for writing your own developed loader and firmware directly RELATED PRODUCTS 802.11 b/g/n 2.4GHz miniPCIe WLE350NX WLE200NX WLE200N2-23 Passive injector PoE Plus POE Plus - Output Voltage: 24VDC - Max Output Watts: 12W PoE2405 - Output Voltage: 24VDC - Max Output Watts: 12W For 5150-5250MHz frequency band, the model WPJ342 just use the antenna which antenna gain is less than 15dBi. For 5725-5850MHz frequency band, the model WPJ342 just use the antenna which antenna gain is less than 25dBi. Before of use, the product and antennas should be installed by the Professional installers. Visit www.compex.com.sg Like us on www.facebook.com/compexsystems Copyright 2013 Compex Systems. All rights reserved. COMPEX and the COMPEX logo are registered trademarks of COMPEX Inc. While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice. DIMENSION DRAWING Compex Systems Pte Ltd 135 Joo Seng Road #08-01 Singapore 368363 Tel: +65 6286 2086 Fax: +65 6280 9947 Email: sales@compex.com.sg Compex (Suzhou) Co Ltd No.12 ChuangTou Industrial Square LouFeng North, Suzhou Industrial Park Suzhou, Jiangsu Province China 215122 Tel: +86 512 62950050 Fax: +86 512 62950026
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 96.47 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Navigation menu