Concealite Life Safety SS2000 Sensor Control Switch User Manual SpaceStation2000 Installation Final3

Download:
Mirror Download [FCC.gov]
Document ID	1620016
Application ID	FpkP7Kyei+3F8ewLUoJwLQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.04kB (563032 bits)
Date Submitted	2012-01-12 00:00:00
Date Available	2012-01-12 00:00:00
Creation Date	2011-09-28 10:20:56
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2012-01-05 09:38:08
Document Title	SpaceStation2000 Installation Final3
Document Creator	CorelDRAW
Document Author:	Concealite

TM
Phone: 605.542.4444
concealite.com
Installation Instructions
SpaceStation Occupancy Lighting Control System
Please Save These Instructions
Important Safeguards
Read and Follow All Safety Instructions
SpaceStation
TM
Do not use outdoors.
þ
þ
Do not let power supply cords touch hot surfaces.
þ
Do not mount units where they will be exposed to direct sunlight, radiators, gas
or electric heaters. Prolonged exposure to temperatures exceeding 95 degrees
Fahrenheit may reduce battery life and void warranty.
þ
Equipment should be mounted securely in locations and at heights where it will
not be readily subjected to tampering by unauthorized personnel.
þ
The use of accessory equipment not recommended by the MANUFACTURER
may cause an unsafe condition.
þ
The AC voltage rating of this equipment is specified on the product label. Do not
connect equipment to any other voltage.
þ
Do not use this equipment for other than its intended purpose.
þ
Servicing of this equipment should be performed by qualified service personnel.
TECHNICAL DATA
Model:
Ac Supply Voltage:
Maximum Load:
Operating Voltage:
Switched Power:
Standby Power:
Hold Time:
Daylight Threshold
Sensor Principle:
Microwave Frequency:
Microwave Power:
Detection Range:
Detection Angle:
Mounting Height:
Operating Temperature:
IP Rating:
SS2000
120/277 Volts (+/- 10%)
120v/400w 230v/1000w 277v/1200w Maximum Ballast Load
50/60hz, 120-277v +/- 10%
400w/1000w/1200w
0.6w (standby), 1.2w (operation)
10 / 30 / 50 / 75 100%, Can Be Customized
5s / 30s / 180s /300s /15min / 25min, Can Be Customized
OPTIONAL: 20FC - 300FC Daylight / Twilight / Darkness,
Can Be Customized
Microwave Motion Detector
5.8 Ghz +/- 75mhz
<1mw
Max. (0 X H): 8m X 10m
02° 150°
0.5 - 100m
-35°c `- +70°c
IP 20 (mounting inside a lamp); IP 65 (mounting in special box)
Copyright© Concealite Life Safety Products. All Rights Reserved. Specifications Subject to Change.
GREENTECHNOLOGY
SpaceStation sensors can
be configured to operate
with any number of
sensors and control any
number of lighting circuits
as one system for any
sized room application.
Index
Important Safeguards
Sensor Mounting
Sensor Adjustments
New Construction/Retrofit
Single Wiring
Multiple Wiring
Adjustable Remote Mounting (ARM)
Troubleshooting
Limited Warranty
All Concealite fixtures are tested and
are guaranteed to be free from
defective materials and workmanship
for a period of three years from date of
shipment under normal operations and
proper use. Correction of all defects
shall be by replacement or repair (at
our discretion) and shall constitute
fulfillment of all manufacturer's
obligations. We will not allow any
charge for labor, materials, etc. that
does not have our written approval
before the work is begun. Damage
incurring in handling or in transit are not
covered by this guarantee. Any other
warranty, expressed or implied, is
hereby void. Modifications to the
product or failure to follow installation
instructions will void the warranty.
v.092611–SS
TM
Instructions
SpaceStation
Phone: 605.542.4444
INSTALLATION | Sensor Mounting
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials.
Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
Area Sensitivity Adjustment (SpaceStation Centered in Room)
Note: Maximum 60' Height Provides Maximum Range Coverage to 50 x 50 Feet
ROOM WIDTH
ROOM LENGTH
Ceiling
Height
8 Feet
10 Feet
12 Feet
Adjustable Range Control Panels (RCP)
controls exact cut off range of each room
Room Area Range Coverage
at Sensitivity % Setting
10%
35%
50%
75% 100%
7'
8'
9'
12'
7'
8'
9'
12'
20'
9'
10'
13'
17'
22'
9'
10'
13'
17'
22'
8'
9'
12'
20'
25'
8'
9'
12'
20'
25'
20'
Step 1: Sensor Mounting
A. Determine mounting location within room or
area to be covered. Center the sensor within
the center of the room/area when possible.
Loosen front knobs.
Loosen Front Knobs to Slide Panels
B. Slide to adjust the four (4) room control panels
to the distance indicated to match the distance in
feet between the sensor and each of the room
wall (to allow activation from any movement within
that room area).
Slide All Four Panels to the Match the Distance
in Feet Between Sensor and Room Walls
v.092611–SS
i
TM
Instructions
SpaceStation
Phone: 605.542.4444
INSTALLATION | Sensor Adjustments
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials. Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
STEP 2: SENSOR ADJUSTMENTS
A. Detection Area
Detection are can be reduced by selecting
the combination on the DIP switches to fit
precisely for each specific application.
B. Hold Time
Hold-time means the time period you
would like to keep the lamp on after the
person has left the detected area.
C. Daylight Sensor
(Remote Option Only)
The sensor contains a daylight sensor in
order to allow a function only below a
defined brightness threshold.
Sensor Adjustments
DETECTION AREA
II
III
IV
100%
75%
50%
30%
10%
ON
HOLD TIME
II
180 S III
300 S IV
15 MIN V
II
III
IV
VI
BRIGHTNESS THRESHOLD SETUP –
DAYLIGHT SENSOR
5S
30 S
DAYLIGHT: The lamp works always, even
during daylight.
2O FC
5O FC
200 FC
300 FC
DISABLE
Note: Three switches should be put in
OFF position when remote day light sensor
is not installed.
25 MIN
ON
ON
v.092611–SS
TM
Instructions
SpaceStation
Phone: 605.542.4444
INSTALLATION | New Construction & Retrofit
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials. Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
Accessible Ceiling Installation: T-Bar Option - Suspended Accessible Ceilings
Note: Use optional T-bar bracket for support mounting to inverted T-grid lay in suspended ceilings.
Inccessible Ceiling Installation: ARM Option - Gypsum Board and Other Inaccessible Ceilings
Note: Use Optional arm bracket for support mounting to structural blocking or stud also for retrofit installation
through existing ceiling hole (see page 8 also).
ARM
Adjustable Remote Mounting
to structural / blocking to
secure SpaceStation
v.092611–SS
i
TM
Instructions
Power Connections
Phone: 605.542.4444
INSTALLATION | Single Wiring Control Wiring Diagram
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials. Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
Red - Line Output to Load
White - Neutral
Black - Line Input
STEP #3: Provide Power Connections
Branch circuit: building power only connections. Provide 120 VAC or 277 VAC uninterrupted power connections to terminate
within the ceiling mounted bracket junction box.
A Option (OR)
Single Lighting Circuit Control Wiring Diagram
A – Optional B – Optional C – Load Information
Optional:
Override FDP
Concealed Wall Switch
Line Input Black
Neutral
Load Output
Line Black
Neutral White
Load Red
Blue
Yellow
Option (RDS)
Optional:
Remote Daylight Sensor
SpaceStation
Occupancy
Sensor
C Load
Load must not exceed 800 watts @ 120 VAC. Load
must not exceed 1200 watts @ 277 VAC. Loads in
excess must use the Command Module option for
higher wattage.
Note: Dimming ballast circuits must be controlled by
the Command Module option.
v.092611–SS
i
TM
Instructions
Power Connections
Phone: 605.542.4444
INSTALLATION | Multiple Wiring Control Wiring Diagram
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials. Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
Multiple Lighting Circuit Control Wiring Diagram
*Required for two or more circuits
A – Optional B – Optional C – Load Information D – Command Module Information
Line Input
Neutral White
Line Black
Neutral White
Neutral
Blue
Yellow
A Option (OR)
Optional:
Override FDP
Concealed Wall Switch
Option (RDS)
Optional:
Remote Daylight Sensor
Load Output Red
SpaceStation
Occupancy
Sensor
C Load
Load must not exceed 800 watts @ 120
VAC. Load must not exceed 1200 watts
@ 277 VAC. Loads in excess must use
the Command Module option for higher
wattage.
Module (CM) – # of poles
D Command
i.e. CM04 - 4 lighting circuit poles
ATTENTION!
Verify line voltage is compatible with electrically held coil voltage
(120 VAC or 277 VAC)
§
Dimming ballast circuits must be controlled by the
Command Module option.
TWO OR MORE SENSORS OPERATING TOGETHER
§
Parallel connect multiple (two or more) sensors for areas
Specified: # of 20 AMP Circuits
exceeding range coverage of one lighting sensor.
v.092611–SS
i
TM
Instructions
Power Connections
Phone: 605.542.4444
INSTALLATION | Adjustable Remote Mounting (ARM)
WARNING: to avoid fire, shock/electrocution, or injury – TURN OFF POWER at circuit breaker or fuse and test to
ensure that power is off before wiring. Remove and discard the packaging materials. Failure to follow published
installation instructions or any modifications to the product may damage the unit and will void the warranty.
ARM – Adjustable Remote Mounting
Provide flexible conduit
connections to existing
Lighting Branch Circuit
Existing
Ceiling
Opening
ARM
Adjustable Remote Mounting
to structural / blocking to
secure SpaceStation
The minimum size opening is 4
inches in diameter for insertion
of SpaceStation into an
inaccessible ceiling opening
Lighting Branch Circuit
Lighting Branch Circuit
Space Station Sensor
Existing Light Fixture,
J Box or Access panel
Existing Ceiling
Note: Dimming ballast circuits must be controlled by the Command Module option.
v.092611–SS
TM
Instructions
Troubleshooting
Phone: 605.542.4444
Troubleshooting
Time Delay
IMPORTANT START-UP INFORMATION
The first time the sensor is powered-up the load will flash ON then OFF once, then there will be 10 seconds while the sensor
warms-up.
The SpaceStation automatically turns OFF the load after the coverage area has been vacant for the amount of time set in the
time delay. The minimum setting is 10 seconds, maximum is 30 minutes.
TROUBLESHOOTING
Quick Test:
Turn the time delay to minimum.
Move out of the sensor's view. Lights should turn OFF after 10 seconds.
Move into the sensor's view. The lights should turn ON.
Lights do not turn OFF:
1. If there is no motion in the set coverage area, reduce the sensitivity varying room panel adjusted positions.
2. Verify room panel adjustment positions.
3. Verify time delay and that there is no movement within the sensor's view for that time period.
FCC NOTICE
This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warranty
All Concealite fixtures are tested and are guaranteed to be free from defective materials and workmanship for a period of three
years from date of shipment under normal operations and proper use. Correction of all defects shall be by replacement or
repair (at our option) and shall constitute fulfillment of all manufacturer's obligations. We will not allow any charge for labor,
materials, etc that does not have our written approval before the work is begun. Damage incurring in handling or in transit are
not covered by this guarantee. Any other warranty, expressed or implied, is hereby void. Modifications or changes to the
product or failure to follow installation instructions will void the warranty.
v.092611–SS

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Page Count                      : 8
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:e7844bd5-8f0d-4eac-ab8e-14a40dd50e63
Producer                        : Corel PDF Engine Version 14.0.0.701
Create Date                     : 2011:09:28 10:20:56-05:00
Creator Tool                    : CorelDRAW
Modify Date                     : 2012:01:05 09:38:08-08:00
Metadata Date                   : 2012:01:05 09:38:08-08:00
Document ID                     : uuid:7f9771ee-1813-45e5-b09a-6ef46cee66b6
Instance ID                     : uuid:6de69c56-54f9-43c4-8274-b1318dd771ee
Format                          : application/pdf
Creator                         : Concealite
Title                           : SpaceStation2000 Installation Final3
Author                          : Concealite

EXIF Metadata provided by EXIF.tools