Concox Information Technology GT800 Vehicle GPS Tracker User Manual 2
Shenzhen Concox Information Technology Co., Ltd Vehicle GPS Tracker 2
User Manual
GPS Vehicle tracker
User Manual
(Version 1.0)
This user manual has been specially designed to guide
you through the functions and features of your GPS
vehicle tracker.
1.Start Guide
1.1 Accessories
◆ Main device
Power cord
4-pin relay
5-pin relay*2
Microphone
SOS cable
Extension cable
Speaker
◆
◆
◆
◆
◆
◆
◆
1.2 Main Functions
◆ Real-time GPS+AGPS tracking
IP66 dust and waterproof
50000 pieces of data storage
Track by time interval or distance
Remotely fuel/power cut-off control
Voice monitor
◆
◆
◆
◆
◆
◆ SOS alarm
◆ Geo-fence alarm
◆ Vibration alarm
◆ Movement alarm
◆ External power supply cut-off alarm
◆ Two way communication
◆ Door status-detection
◆ Multiple analog & digital input/output
◆ Find the car by triggering light and buzzer
Power
Oil/electricity
ACC
Data
Extension
interface
SOS button
MIC
Speaker
1.3 Specifications
Frequency GSM 850/900/1800/1900MHz
Class 12, TCP/IPGPRS
9-36VDC / <300mAOperating Voltage
Cold Start: ＜35s
Location Time Hot Start：＜2s
<10 metersLocation Accuracy
-20℃ ~ +70℃
83（L）×76（W）×18（H）mm
95g
Operating Temperature
Dimension
Weight
2.My Device
2.1 Appearance
GPS LED indicator
Power status
7
8
9
7
8
9
GSM LED indicator
64MBStorage
800mAhBattery
3.1 Wire Definition
Line Color Definition
Description
1
2
3
4
Red
Black
Orange
Yellow
PW+
GND
ACC
RELAY
12V/24V car battery positive
12V/24V car battery negative
ACC ignition
Relay
5
6
7
8
Red
Blue
Green
Black
5V-OUT
RX
TX
GND
External power supply
Data receiving / backup interface
Data sending/ backup interface
GND(negative)
9Purple ADC
10
11
Orange
Yellow
In1
OUT1
12 Black GND
13 Orange SOS+ SOS button
14 Brown MIC+
15 Black MIC- Microphone
16 Grey SPK+
17 Black SPK- Speaker
Analog input
Digital input
Output, Relay
3. Wire Connection
3.2 Wiring diagram
MIC
Microphone
SOS
Extension
interface
Data
Power
Oil/electricity
ACC
Relay
Storage
battery
Speaker
Notice: Purple line (ADC) of terminal connects to analog signals line,
like voltage of external device, analog temperature sensor, fuel sensor.
Voltage detected by analog signal ranges from 0~30Vdc.
/
Oil pump
Ignition key
Connection
Outout control Connection
Analog signal
Diagram 1
Negative trigger
connection car type
Positive trigger
connection
car type
Door negative
trigger connection
Door light
Door positive
trigger connection
Door light
Diagram 2
Diagram 3
Relay 1
Relay 2
Car left signal wire
Left turn light
Car right signal wire
Right turn light
Connect to turn light
Car
horn
button
Relay 1
Relay 2
Car horn relay
Car left signal wire
Car right signal wire
Connect to car horn
and turn light
Door switch
Door switch
Left turn light
Right turn light
1.The standard power supply ranges from 9V to 36VDC. Please use
the power cord manufactured by the original factory. Red line means
positive side while black line means negative side. During
installation, negative side should connect to the ground, do not
connect with other ground wires at the same time.
2.ACC line (orange) connects to vehicle's ACC switch, detecting
ignition on and off.
3.Device's oil and electricity control line (yellow) connects to relay's 86.
(thin yellow line of relay socket)
Wiring Instruction
Relay wiring instruction
Relay wiring way of oil pump open circuit: On each end of the wire is thin
white line (85) and thin yellow line (86). Thin white line (85) connects to
the positive side of battery (12V) while thin yellow line (86) connects to the
device relay control. There is an oil pump in the vehicle. Cut off the
positive line. The positive side of oil pump connects to the close-end of
relay.(Thick green line 87a), and the other side connects to relay's
common(green thick 30).
Notice
12V relay is standard. The device is suitable for vehicles with 12V
battery. If the vehicle has 24V battery, then 24V relay is needed.
4.To monitor analog signals, the purple line (ADC) of extended port
should be connected to the analog line.
5.To check status of car door, orange line (IN1) should be connected
to where between the door light and door switch (See the diagram).
6.To find car remotely, please connect the yellow line (OUT1) of
extended port to external relay.
Wiring instruction for remote trigger car light and buzzer
Thin white line (85) and thick green line (87) of relay should be connected
to car battery's positive pole. The thin yellow line (86) is connected to the
yellow line (OUT1) of extended port. Cut off the line of car turn light first
and then connect one side with turn light to the common terminal (thick
green line 30) and other side to closed terminal (thick green line 87a). See
diagram for wiring way.
4. Operation of device
Power on/ Power off
Power on: Once you insert a valid SIM card and connect all the
wires, turn on the device. Power LED will flash first. During signal
searching process, GSM LED and GPS(blue) LED will flash. Once
Blue GPS LED keeps steadily ON, it means the device has been
located and it starts to work.
Power off: Just toggle off the power switch.
Notice:
When device is connected with external power, please turn on the
battery switch. The battery will then connect with the device circuits
and its built-in battery will be charged. If battery is OFF, battery can't
be charged. The device will be power off if no external power supply.
3.3 Device Installation
Devic e
Devic e
Devic e
Around dashboard
Under rear windshield
Under front windshield
Note：
The device should face up to the sky.
Metal thermal barrier or heating layer of the windshield affects the
signal. Please change installation places to receive better signal.
5. Main Functions
5.1 SOS
In emergent case, press SOS for 3 seconds to activate SOS alarm.
Then the device will send SOS SMS to preset SOS numbers and
then dial the numbers in a loop for 3 times until the call is picked up.
Alarm message will also send to platform. (See command list 7-9)
5.2 Power cut-off alarm
When the electricity supply of device is cut off, it will activate cut-off
alarm.
5.3 Low battery alarm
When battery is low, the device will activate low battery alarm.
Device will send alert through SMS and to the platform.
5.4 Vibration alarm (default OFF)
When vehicle vibrates for several times, the vibration alarm will be
triggered. If ignition keeps OFF for 3 minutes (ACC OFF), the device
will send vibration alarm message immediately.(See command list 7-
13)
5.5 Voice monitoring
1.
2.
voice
When MIC and speaker are connected, use pre-set SOS number to
When MIC is connected while speaker is not, use pre-set SOS
number to dial the device, after 10 seconds, device enters into
monitoring mode automatically. The caller can hear the inside
the vehicle.
send command to the device. Device would automatically call
you back in a second. Pick up and monitor the voice inside the
vehicle.
JT#
When vehicle is stolen, oil/electricity cut-off command can be sent
by platform, APP or SMS.
Notice
1.Make sure ACC is correctly connected.
2.When ACC is OFF, command will be executed immediately.
3.When ACC is ON, but GPS is not fixed, command will be postponed.
4.When ACC is ON, GPS is fixed, command will be executed when
vehicle speed is less than 20km/h.
If you want to cut off/restore oil by SMS command, you have to set a
center number firstly. Only the center number can send the cut
off/restore oil command to the device.
Notice
1.Only the SOS number can be used to set center number.
2.Only the SOS number can be used to delete center number.
3.There is only one center number can be set.
(See command list 7-15)
5.6 Two-way communication
To activate this function, ensure that both MIC and speaker are
connected well.
Use pre-set SOS number to dial the device, after 10 seconds, device
enters into two-way talk mode.
5.7 Displacement alarm(default OFF)
Device will send movement alarm when vehicle moves out the pre-
set distance (when ACC is off and GPS is fixed).
5.8 Oil/Electricity cut-off
Notice
1.Pre-set SOS number is necessary.
Non-SOS number cannot activate this function.
2.SIM card of device must have caller ID sevice.
5.9 Restore oil/electricity
When alarm is all-clear, you can send restore oil/electricity
command by platform, APP or SMS and restore vehicle power.
(See command list 7-16)
5.10 Restart device
If GPRS is abnormal (device is offline), user can send SMS
command to restart the device. Device will reboot after 20
seconds after receiving the command.
RESET#
(See command list 7-17)
5.11 Door detection
The device is able to detect door status. It uploads car status to
platform and APP timely. Negative triggering is default. When car
door's status is negative triggering, there is no need to set. Instead,
if car door status is positive triggering, the triggering way has to be
modified. (Command: ). See 3.3 diagram-2 for wiring way.
(
Notice
Negative triggering (default): when door is open, signal level of door
is 0V; when door is closed, signal level of door is power voltage.
Positive triggering: when door is open, signal level of door is power
voltage; when door is closed, signal level of door is 0V.
DOOR,1#
See command list 7-18)
5.12 Analog signal
The device can measure car battery's voltage and upload it to
platform/APP in fixed time based on your needs. Purple line (ADC)
of device extended port can receive analog signal, like voltage of
external device, analog temperature sensor and fuel sensor. Voltage
range of analog input is 0~30Vdc. See 3.3 diagram for wiring way.
(See command list 7-19)
6.Platform Operation
Get registered on the designated service platform by authorized
dealer, then you can start the tracking service and settings.
6.2 Login service platform
Please login the designated sevice platform to set and operate the
device.
6.3 Download APP
Please download and install the APP in designated website, APP
store or Google Play store.
5.13 Find the car by triggering
light and buzzer
When need to pick out the car parking on giant parking lot, you can
send a command. After the device receives the command, it will
control turn light relay or horn relay by the yellow line of extended
port, so as to trigger the car's light or horn. In this way, you can figure
out your car's position easily and accurately. See for
wiring way. (See command list 7-20)
3.3 diagram-3
6.1 APN & Server setting
To ensure normal network operation, please confirm your APN and
server setting before login.
(See command list 7-8)
In most countries, APN could be automatically adapted to local
mobile operators. If not, please send SMS to set the APN.
If username and password is required for APN, please add it into the
command. (See command list 7-7)
Confirm the server address and setting with distributors. If server is
incorrect, please send SMS to change.
7.Common Command List
Edit SMS command in the right column to the device SIM number to
achieve respective function as below:
STATUS#1 Device status
WHERE#2 Device coordinate
URL#3 Location URL
APN setting
1. Add SOS number:
2.Delete subjected sequence of SOS
number:
E.g. SOS,D,1,2,3#
3. Delete the SOS number：
4. Query SOS number：
SOS,A,number 1,number 2,number 3#
SOS,D,number sequence 1,
number sequence 2, number sequence 3#
SOS,D,phone number#
SOS#
8
SOS setting
TIMER,T1,T2#
T1=5～18000 seconds；ACC ON upload
interval；default value：10
T2=5～18000 seconds；ACC OFF upload
interval；default value：10(when GPS is
not sleep)
10 GPS data upload
time interval
1.
E.g: APN,internet#
2.
E.g: APN,internet,CLIENTE,AMENA#
APN, [apnname]#
APN, [apnname],[user],[pwd]#
SERVER,mode,domain/IP,port,0#
E.g. SERVER,1,www.ydpat.com,8011,0#
SERVER,0,211.154.135.113,8011,0#
mode1 means set with domain name
mode 0 means set with ip address
7
Server setting
VERSION#4 Check version
GPRSSET#5 Network setting
9
PARAM#6 Check parameter
17
RESET#
Device restart 20 seconds after receiving
this command
Restart
DISTANCE,D#
D=0、50～10000 meter；
Distance interval；default value：300,
unit：meter；
11
GPS data upload
distance interval
DEFENSE,A#
A:1～60 minutes，set delayed defense，
default value：10 minutes
12 Delayed defense
setting
1.
2.
SENALM,ON#
SENALM,OFF#
13 Vibration alarm
(default OFF)
1.
R=100～1000; Displacement radius，
unit: meter
M=0-2; Alert way
0:GPRS，1:SMS+GPRS；
2: GPRS+SMS+CALL
E.g. MOVING,ON,200,2#
2.
MOVING,ON,R,M#
MOVING,OFF#
14 Displacement alarm
setting
(default OFF)
RELAY,A#
A=0/1
0= restore petrol; 1=cut off petrol
Default value：0
E.g. RELAY,1#
16 Power/oil control
Set center number :
Delete center number:
CENTER,A,mobile number#
CENTER,D#
15 Set center number
DOOR,A#
A=0/1; 0 negative triggering，
1 positive triggering；
default: 0
18
Car door negative/
positive triggering
setting
Upload analog data:
T: upload interval; scope: 5∼3600(second)
Turn off analog upload: ；
default: OFF
ADT,ON,T#
ADT,OFF#
19 Analog upload
setting
FIND#
Find car by
triggering light
and buzzer
20
8.Trouble shooting
If you are having trouble with your device, try these troubleshooting
procedures before contacting a service professional.
Problems Causes
Using the GPS tracker in the
places that have good signal
condition.
Poor signal
The signal waves
unable to transmit
when use the GPS
tracker in the places
that have poor signal
reception, such as:
tall building around
or basement.
Solutions
Charge the device battery
Unable to
boot Low battery
Using the GPS tracker in the
places that have good signal
condition.
Unable to
connect to
the network
Poor signal
Change the installation place
Unable to
locate
Signal shielded
or Poor signal
Turn it on
No power
off alarm Built-in battery is off
Restore power/Check ACC
Fail to start
the car
Power cutoff /
ACC abnormal
Connect the device negative
electrode to constant power
Car stops
driving
Abnormal power
supply
Check power supply/Press
side key to activate indicators
Offline/
Indicators off
Abnormal power
supply/Indicators
sleep
Test the device again/
Change installation place
No update
of vehicle's
location
No GPS positioning
Warranty instructions and service
1. The warranty is valid only when the warranty card is properly
completed, and upon presentation of the proof of purchase
consisting of original invoice indicating the date of purchase, model
and serial No.of the product. We reserve the right to refuse warranty
if this information has been removed or changed after the original
purchase of the product from the dealer.
2. Our obligations are limited to repair of the defect or replacement
the defective part or at its discretion replacement of the product
itself.
3. Warranty repairs must be carried out by our Authorized Service
Centre. Warranty cover will be void, even if a repair has been
attempted by any unauthorized service centre.
4. Repair or replacement under the terms of this warranty does not
provide right to extension or renewal of the warranty period.
5. The warranty is not applicable to cases other than defects in
material, design and workmanship.
Maintenance Record
Date Serviced by
Product Model
IMEI Number
Fault
Descriptions
Comments
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.