Controlled Entry Distributors 418ELPW1K Model 418ELPW1K User Manual Exhibit 8

Download:
Mirror Download [FCC.gov]
Document ID	662326
Application ID	Q7skoBFFRgFWi6aZXYRp+A==
Document Description	Exhibit 8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.51kB (168865 bits)
Date Submitted	2006-05-26 00:00:00
Date Available	2006-05-26 00:00:00
Creation Date	2006-05-23 12:56:43
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2006-05-23 12:56:47
Document Title	ELECTRONIC CARD TX SETW295AM2 – Front internal view
Document Creator	Acrobat PDFMaker 5.0 per Word
Document Author:	product_mgr

ELPRO INNOTEK S.p.A.
TCF-107
MONARCH ONE BUTTON - Type: 418ELPW1K
Annex 8 : User manual
The Transmitter Solutions - 418R receiver which operates with this
transmitter has a Wiegand 26 bit output and can operate any type of
access control system equipped with the same protocol. The CR 2016
lithium batteries of the transmitter have a shelf life of about 6 months.
The product fully complies with Part 15 of FCC Regulations and the
European Directives 99/5/CE, 89/336/CEE, 73/23/CEE.
1B - Technical specifications
Transmitter
Solutions
Thank you for choosing a Transmitter Solutions product .
Please read this manual carefully before using the product.
Made in Italy. Copyright © 2006 by Transmitter Solutions
CONTENTS
1 - TRANSMITTER OVERVIEW
1A - General information
1B - Technical specifications
1C - Main components
Operating frequency
418 MHz
Number of keys:
Battery :
2 x 3V lithium batteries CR2016
Battery life:
18 ÷ 24 months
Number combinations :
65,536
Protocol :
Elite compatible
Different Facilities codes
256
Operating temperature:
-20°F÷+131°F (-20°C÷+55°C)
Overall dimensions:
2.4”x1.4”x0.51” (61x36x13 mm)
Weight:
0.49 oz. (14 gr.)
1C - Main components
2 - NUMBERING
3 - PROGRAMMING
Red
LED
4 - OPERATION
5 - BATTERY ACCESS
Green
push-button
6 - TROUBLESHOOTING
1A - General information
The Transmitter Solutions - Monarch 418ELPW1K transmitter is a key
chain style mini transmitter operating at 418 MHz. It has been designed
for use with programmable telephone entry, security, and access control
systems operating with a 418 MHz frequency receiver. The code sent by
the transmitter includes a 16 bit security code which allows up to
65,536 code combinations and 8 bits of facility code which allows up to
256 facility codes .
Dark grey
case
Key ring
holder
Fig. 2
6 - TROUBLESHOOTING
2 - NUMBERING
Each transmitter is manufactured and sold with a different factory-set serial
number .
3 - PROGRAMMING
The transmitter must be programmed into your system memory.
Your own installer or reseller will provide you the necessary instructions for your
system.
PROBLEM
SOLUTION
The system does not receiver the
transmitter signal.
The transmitter LED will not light
Replace the transmitter
batteries
The system does not receiver the
transmitter signal.
The transmitter LED is ON
Check to verify the
transmitter is programmed
into your system
The operating range is reduced
Replace the transmitter
batteries
4 - OPERATION
A - Firmly depress the button until the small red LED illuminates.
B - After the LED has illuminated, release the button.
If the device you are attempting to activate does not respond, repeat steps A and B
or consult section 6 ( Troubleshooting ) of this manual.
Transmitter Solutions - Type : 418ELPW1K
FCC ID : SU7418ELPW1K
5 - BATTERY ACCESS
To access the battery open the case with a screwdriver acting on the slot between
the cover and the bottom and remove the bottom, as shown in fig. 3a and 3b.
Slide out the old batteries and replace them with the new ones [CR2016]
respecting the polarity, with the positive (+) side upward.
NOTE: Please dispose of the batteries properly according to local laws and
regulations.
Test proper battery installation by verifying that the red LED illuminates when
the button is pushed.
Fig. 3a
This device complies with Part. 15 of the FCC Rules
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept interference received, including
interference that may cause undesired operation.
Notice
Any changes or modification to Transmitter Solutions equipment not expressly
approved by Transmitter Solutions could void the manufacturer’s warranty.
WARRANTY
The warranty period of Transmitter Solutions 418 transmitters is 24 months,
beginning from the manufacturing date of the transmitter. During this period, if the
product does operate correctly, due to a defective component, the product will be
repaired or replaced at the sole discretion of Transmitter Solutions.
The warranty does not extend to the transmitter case which can be damaged by
conditions outside the control of Transmitter Solutions or to battery life.
Fig. 3b
TRANSMITTER SOLUTIONS
2505 Chandler Avenue, Suite, 1
Las Vegas, NV 89120 (866) 975-0101 - (866) 975-0404 Fax
sales@transmittersolutions.com
IS-TM141CCUK Rev. 1 del 19.05.2006
Annex 8 = User manual
Pag 1 of 1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2006:05:23 12:56:47+03:00
Create Date                     : 2006:05:23 12:56:43+02:00
Page Count                      : 1
Creation Date                   : 2006:05:23 10:56:43Z
Mod Date                        : 2006:05:23 10:56:43Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : product_mgr
Metadata Date                   : 2006:05:23 10:56:43Z
Creator                         : product_mgr
Title                           : ELECTRONIC CARD TX SETW295AM2 – Front internal view
Page Mode                       : UseNone
Tagged PDF                      : Yes

EXIF Metadata provided by EXIF.tools