Controlled Entry Distributors 433TSPW1K Model 433TSPW1K User Manual Exhibit 8

Controlled Entry Distributors, Inc. Model 433TSPW1K Exhibit 8

Exhibit 8

ELPRO INNOTEK S.p.A. TCF-104 Annex 8 = User manual Pag 1 of 1 MONARCH ONE BUTTON - Type: 433TSPW1K Annex 8 : User manual 1A - General informationThe Transmitter Solutions - Monarch transmitter is a key chain style mini transmitter operating at 433,92 MHz. It has been designed for the control of automatic closing systems and anti-burglar systems, thanks to its very high security coding system (KeeLoq® Hopping code). The code sent by the transmitter changes at each activation, avoiding any scanning and copying risk. A special algorithm allows to keep synchronized transmitter and receiver. CONTENTS1A - General information1B - Technical specifications1C - Main components1 - TRANSMITTER OVERVIEW2 - NUMBERING3 - PROGRAMMING4 - OPERATION5 - BATTERY ACCESS1B - Technical specificationsOperating frequency 433,92 MHzNumber of keys: 1 Battery life: 18 24 monthsSecurity code: Keeloq Hopping codeNumber combinations : 2exp64Operating temperature: -20°F÷+131°F (-20°COverall dimensions: 2.4”x1.4”x0.51” (61x36x13 mm)Weight: 0.49 oz. (14 gr.)Battery : 2 x 3V lithium batteries CR2016÷®÷+55°C)The transmitter can operate with many receivers of the range Transmitter Solutions - 433R. Ask your installer or reseller the product which best fits your application. The output of the receivers can be either wiegand 26 bit ( to communicate with access control systems ) or 1-2-4 relay with NO - NO/NC output. The CR 2016 lithium batteries of the transmitter have a shelf life of about 6 months. Part 15 of FCC Regulations and The product fully complies with the European Directives 99/05/CE, 89/336/CEE, 73/23/CEE.1C - Main componentsRed LEDKey holder ring Dark redpush-button6 - TROUBLESHOOTINGDark grey caseFig. 2TransmitterSolutionsThank you for choosing a Transmitter Solutions product .Please read this manual carefully before using the product.Made in Italy. Copyright © 2006 by Transmitter Solutions 2 - NUMBERING 6 - TROUBLESHOOTINGPROBLEM SOLUTIONThe operating range is reducedCheck to verify the transmitter is programmed into your systemReplace the transmitter batteriesIS-TM143CCUK Rev. 1 del 19.05.2006To access the battery open the case with a screwdriver acting on the slot between the cover and the bottom and remove the bottom, as shown in fig. 3a and 3b. Slide out the old batteries and replace them with the new ones ] respecting the polarity, with the positive (+) side upward. [CR2016NOTE: Please dispose of the batteries properly according to local laws and regulations. Test proper battery installation by verifying that the red LED illuminates when the button is pushed.5 - BATTERY ACCESS3 - PROGRAMMINGEach transmitter is manufactured and sold with a different factory-set serial number .The transmitter must be programmed into your system memory. Your own installer or reseller will provide you the necessary instructions for your system.Replace the transmitter batteriesThe warranty period of 433 transmitters is 24 months, beginning from the manufacturing date of the transmitter. During this period, if the product does operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of . The warranty does not extend to the transmitter case which can be damaged by conditions outside the control of Transmitter Solutions or to battery life.Transmitter SolutionsTransm itter SolutionsWARRANTYTransmitter Solutions - Type : 433TSPW1KFCC ID : SU7433TSPW1KThis device complies with FCC Rules Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.Part. 15 of the NoticeAny changes or modification to equipment not expressly approved by could void the manufacturer’s warranty.Transmitter SolutionsTransmitter SolutionsThe system does not receiver the transmitter signal.The transmitter LED is ONThe system does not receiver the transmitter signal.The transmitter LED will not light4 - OPERATIONA - Firmly depress the button until the small red LED illuminates.B - After the LED has illuminated, release the button. If the device you are attempting to activate does not respond, repeat steps A and B or consult section 6 ( Troubleshooting ) of this manual.Fig. 3aFig. 3bTRANSMITTER SOLUTIONS2505 Chandler Avenue, Suite, 1 Las Vegas, NV 89120 - (866) 975-0101 - (866) 975-0404 Faxsales@transmittersolutions.com

Navigation menu