Controlled Entry Distributors FM420U 433.9 MHz REMOTE TRANSMITTER User Manual FM420U v 11 2013

Controlled Entry Distributors, Inc. 433.9 MHz REMOTE TRANSMITTER FM420U v 11 2013

User Manual

FM420UISTFM420UV.06.2013ENMULTI-CHANNEL 433.92 MHz RADIO CONTROL.Operation and programming instructions.
ENFig. 1Fig. 222CR2430214.2116.040.8dimensions in mm201354DISPLAYEN3SPECIFICATIONSMulti-channel radio control for quick and intuitive control of 20 users with receivers in the series FM400UInnovative and stylish container with white led display which, located under semi-transparent plastic, shows the selected channel. At the centre of a rubber faced keypad with three function keys and two up-down channel selection keys. Fitted with practical non-slip rubber buttons.TECHNICAL SPECIFICATIONS u.m. FM420Power supply with battery type Vdc 3 (CR2430)Transmission consumption mA 50Frequency MHz 433,92Modulation FSKOperating temperature °C -20 +55Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ENFig. 1Fig. 222CR2430214.2116.040.8dimensions in mm201354DISPLAYEN3SPECIFICATIONSMulti-channel radio control for quick and intuitive control of 20 users with receivers in the series FM400UInnovative and stylish container with white led display which, located under semi-transparent plastic, shows the selected channel. At the centre of a rubber faced keypad with three function keys and two up-down channel selection keys. Fitted with practical non-slip rubber buttons.TECHNICAL SPECIFICATIONS u.m. FM420Power supply with battery type Vdc 3 (CR2430)Transmission consumption mA 50Frequency MHz 433,92Modulation FSKOperating temperature °C -20 +55Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ENUse key 1 or 3 (indicated in the drawing) to scroll through to the flashing Use the central key to confirm The channel will start flashing. Use key 3 (indicated in the drawing) or 1 to scroll through the channels to Press key 2 to add the channel 02 to C2. The dot next to 2 will light up ( ).To remove it from C2 press key 4, and the dot next to 2 will turn off ( ).If a dot is lit next to 0 ( ), this means that channel 02 also belongs to group C1.Use key 3 (indicated in the drawing) or 1 to scroll through the channels to Press key 2 to add the channel 15 to C2. The dot next to 5 will light up ( ).To remove it from C2 press key 4, and the dot next to 5 will turn off.5EN4DESCRIPTION OF COMPONENTSFig. 11 channel decrease key2. CH1 transmission key3. channel increase key4. CH2 transmission key5. CH3 transmission keyMAIN FUNCTIONSFig. 2Battery panel opening and external dimensions in mmThis transmitter can control up to 20 automations, each of which can be sent 3 different functions (for example OPEN, CLOSE and STOP).To scroll through the 20 channels, press key 1 (to decrease the number) or 3 (to increase the number).After selecting the channel, press keys 2, 4 or 5 to transmit the code.To memorise the code in the user, read the receiver instructions.Press and hold the the keys indicated in the drawing (1 and 3) until starts to flash.-Channels groups (C1, C2).Use this menu to group channels as required. Once configured, press a command for C1 or C2 to transmit all selected channels in sequence.Example: how to group channels 02 and 15 in C2SPECIAL FUNCTIONS
ENUse key 1 or 3 (indicated in the drawing) to scroll through to the flashing Use the central key to confirm The channel will start flashing. Use key 3 (indicated in the drawing) or 1 to scroll through the channels to Press key 2 to add the channel 02 to C2. The dot next to 2 will light up ( ).To remove it from C2 press key 4, and the dot next to 2 will turn off ( ).If a dot is lit next to 0 ( ), this means that channel 02 also belongs to group C1.Use key 3 (indicated in the drawing) or 1 to scroll through the channels to Press key 2 to add the channel 15 to C2. The dot next to 5 will light up ( ).To remove it from C2 press key 4, and the dot next to 5 will turn off.5EN4DESCRIPTION OF COMPONENTSFig. 11 channel decrease key2. CH1 transmission key3. channel increase key4. CH2 transmission key5. CH3 transmission keyMAIN FUNCTIONSFig. 2Battery panel opening and external dimensions in mmThis transmitter can control up to 20 automations, each of which can be sent 3 different functions (for example OPEN, CLOSE and STOP).To scroll through the 20 channels, press key 1 (to decrease the number) or 3 (to increase the number).After selecting the channel, press keys 2, 4 or 5 to transmit the code.To memorise the code in the user, read the receiver instructions.Press and hold the the keys indicated in the drawing (1 and 3) until starts to flash.-Channels groups (C1, C2).Use this menu to group channels as required. Once configured, press a command for C1 or C2 to transmit all selected channels in sequence.Example: how to group channels 02 and 15 in C2SPECIAL FUNCTIONS
ENPress key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.- Maximum number of channelsDisplay of channels can be set to the minimum indispensable, to optimise search times.Procedure:To increase battery lifetime, set a short delay interval.Groups C1 and C2 are only displayed if programmed.From the secondary menu, press key 5 to select Use key 3 (indicated in the drawing) or 1 to scroll through values 00 to 20.Example: on selection of 12, all channels from 00 to 15 will be displayed.Press key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.Use key 2 (indicated in the drawing) or 4 to scroll through values to corresponding to a display shutdown delay from approx. 2 to 10 seconds. 7EN6Use the central key to complete programming of C2. The text is displayed briefly, followed by after which the display turns off.Access to secondary menuThis menu contains the following functions:- Display shutdown delay setting- Maximum channel number setting- Channel 00 repetition function- Firmware VersionProcedure to enable secondary menu:Press and hold the keys indicated in the drawing for approx. 10 seconds until appears.key 3 (indicated in the drawing) or 1 to scroll through the menu until the required function is displayed- Display shutdown delayThe channel remains on display after release one of the keys for a time interval that can be modified as follows:From the secondary menu, press key 5 to select
ENPress key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.- Maximum number of channelsDisplay of channels can be set to the minimum indispensable, to optimise search times.Procedure:To increase battery lifetime, set a short delay interval.Groups C1 and C2 are only displayed if programmed.From the secondary menu, press key 5 to select Use key 3 (indicated in the drawing) or 1 to scroll through values 00 to 20.Example: on selection of 12, all channels from 00 to 15 will be displayed.Press key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.Use key 2 (indicated in the drawing) or 4 to scroll through values to corresponding to a display shutdown delay from approx. 2 to 10 seconds. 7EN6Use the central key to complete programming of C2. The text is displayed briefly, followed by after which the display turns off.Access to secondary menuThis menu contains the following functions:- Display shutdown delay setting- Maximum channel number setting- Channel 00 repetition function- Firmware VersionProcedure to enable secondary menu:Press and hold the keys indicated in the drawing for approx. 10 seconds until appears.key 3 (indicated in the drawing) or 1 to scroll through the menu until the required function is displayed- Display shutdown delayThe channel remains on display after release one of the keys for a time interval that can be modified as follows:From the secondary menu, press key 5 to select
EN9EN8- Channel 00 repetition This new multi-channel control enables programming of channel 00 so that it repeats transmission sequentially for a set time interval. This function is useful when channel 00 is optimised for centralised commands, and repetition optimises reception of the radio signal.Press key 5 to select Press key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.In this case (30) channel 00, after pressing a transmission key, is transmitted at regular intervals for 30 seconds. On each transmission, the text is displayed, followed by . Press key 1 or 3 to interrupt transmission repetition.To disable repeated transmission of channel 00, set in the menu .Use key 2 (indicated in the drawing) or 4 to scroll through values 00 to 40.Select 00 to disable transmission repetition.Select 10, 20, 30 or 40 to set the repetition interval in seconds.- Firmware VersionPress key 5 to select . This displays a number corresponding to the radio control firmware version.BATTERY REPLACEMENTTo replace the battery, open the battery compartment and remove the battery with the aid of a tool (for example the tip of a pen). Fit the new battery taking care to observe polarity. See fig. 2 on page 2.GUARANTEEThe present guarantee covers possible faults and/or irregularities due to manufacturing defects and/or faults. The guarantee will automatically decay in the event of tampering or mi-suse of the product.During the guarantee period TELCOMA srl pledge to repair and/or re-place defective and non-tampered parts. The call charges, as well as the collection, packaging and transportation costs of the product for re-pair or replacement are at the clients full and exclusive expense.
EN9EN8- Channel 00 repetition This new multi-channel control enables programming of channel 00 so that it repeats transmission sequentially for a set time interval. This function is useful when channel 00 is optimised for centralised commands, and repetition optimises reception of the radio signal.Press key 5 to select Press key 5 to confirm. The text appears briefly and the radio control returns to normal operating status.In this case (30) channel 00, after pressing a transmission key, is transmitted at regular intervals for 30 seconds. On each transmission, the text is displayed, followed by . Press key 1 or 3 to interrupt transmission repetition.To disable repeated transmission of channel 00, set in the menu .Use key 2 (indicated in the drawing) or 4 to scroll through values 00 to 40.Select 00 to disable transmission repetition.Select 10, 20, 30 or 40 to set the repetition interval in seconds.- Firmware VersionPress key 5 to select . This displays a number corresponding to the radio control firmware version.BATTERY REPLACEMENTTo replace the battery, open the battery compartment and remove the battery with the aid of a tool (for example the tip of a pen). Fit the new battery taking care to observe polarity. See fig. 2 on page 2.GUARANTEEThe present guarantee covers possible faults and/or irregularities due to manufacturing defects and/or faults. The guarantee will automatically decay in the event of tampering or mi-suse of the product.During the guarantee period TELCOMA srl pledge to repair and/or re-place defective and non-tampered parts. The call charges, as well as the collection, packaging and transportation costs of the product for re-pair or replacement are at the clients full and exclusive expense.
1110NOTENOTE
1110NOTENOTE
Telcoma s.r.l.via L. Manzoni, 11 z.i. Campidui31015 Conegliano (TV) ItalyTel. +39 0438-451099 - Fax +39 0438-451102http://www.telcoma.it E-mail:info@telcoma.it

Navigation menu