Controlled Entry Distributors RCOO900P Remote Controller User Manual
Controlled Entry Distributors, Inc. Remote Controller Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3886214 |
| Application ID | +TOUq1o3+yvn+HGa42zgvw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 153.83kB (1922870 bits) |
| Date Submitted | 2018-06-13 00:00:00 |
| Date Available | 2018-06-13 00:00:00 |
| Creation Date | 2018-05-24 10:59:47 |
| Producing Software | Adobe PDF Library 9.9 |
| Document Lastmod | 2018-06-12 16:05:08 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS5.5 (7.5.3) |
iGAZE® REP KIT Transceiver System for 10kΩ, or 8.2kΩ Resistive Safety Edges Pulsed output BI-DIRECTIONAL COMMUNICATION Fixed Device RCOO900P Movable Device TCOO900 INSTRUCTION MANUAL v.05.24.18 TRANSCEIVER SYSTEM FOR SAFETY EDGES TECHNICAL SPECIFICATIONS Movable device name TCOO900 Fixed device name RCOO900P Frequency 902-928 Mhz Range of the system in free space 20 m / 60 feet TCOO900 power supply 2 x 1.5V batteries (AA) RCOO900P power supply 12/24 Vac-dc Battery duration 2 years (normal functioning mode). 5 years (Low power mode). Minimum battery level (TCOO900) 1.9V Compatible safety edges (TCOO900) Resistive (8.2 kΩ / 10kΩ) Number of outputs (RCOO900P) Maximum number of Transmitters for each RCOO900P 8 for each device. Maximum number of safety edges for each output 8 for each relay. Power draw on RCOO900P (24Vdc) 15mA (3-wire or 4-wire pulsed) 50mA (2-wire pulsed) Resistive Safety Edge (max value) 5kOhm < R < 20KOhm (safety edge OK) R<5KOhm (safety edge in short circuit) R>20KOhm (OPEN safety edge) Frequency for alternate current (RCOO900P) 50-60Hz Operating Temperature -10°C to +55°C / 14°F to 131°F QUICK START GUIDE BELOW IS THE MOST COMMON INSTALLATION RCOO900P - Pulsed 2 Frequency on both channels OFF RCO900P OFF ON Dip switch Buzzer 2Freq/3Freq Buzzer OFF Frequency ON DIP TCOO900 - Both safety edges are 8.2kΩ or 10kΩ resistive. Led and programming / test key 2 Led and programming / test key 1 Out1 - 10k Resistive edge 2 8.2kΩ / 10kΩ (N.C.) Safety2 Resistive edge 2 Safety1 Resistive edge 1 Out2 - 10k Programming/ Reset key + 12/24 Vac/Vdc Resistive edge 1 8.2kΩ / 10kΩ (N.C.) operator 1 pulsed input operator 2 pulsed input A DESCRIPTION The iGAZE® REP transceiver system is intended as a safety device for automated gates and rolling doors. The system is comprised of 1 fixed device (RC00900P) with 2 pulsed outputs, which is connected to the operator, and up to 8 movable devices (TC00900) for each relay. The system TCOO900 will accept only resistive safety edge 10kΩ or 8.2kΩ. The transmission signal is bi-directional and utilizes the frequencies 902-928MHz. Maximum range between the movable and fixed devices is 60 feet. TCOO900 is suitable for outdoor use. RCOO900P is suitable for indoor use only (“indoor” means inside the operator box). The installation of the system must be carried out by a qualified installer. CONFIGURATION AND ELECTRICAL CONNECTIONS ATTENTION! If external operators or devices are installed, wiring type CL2, CL2P, CL2R or CL2X complying with UL 13 or other cable with equivalent or better electrical, mechanical, and flammability ratings shall be used. STEP 1 DIP SWITCHES CONFIGURATION OF TCOO900 N°DIP Function TCOO900 DIP ON 2 Frequency channel selection 3 (see page 4) OFF Low Power (see section E on page 9) (All switches in example above are set to OFF) STEP 2 CONNECT THE SAFETY EDGE TO THE SAFETY EDGE MOVABLE DEVICE (TCOO900) OFF Dip switch ON DIP EXAMPLE 1 - Both safety edges are 8.2kΩ or 10kΩ resistive Led and programming / test key 2 Led and programming / test key 1 Resistive edge 2 8.2kΩ / 10kΩ (N.C.) Safety2 Resistive edge 2 Safety1 Resistive edge 1 Resistive edge 1 8.2kΩ / 10kΩ (N.C.) STEP 3 SET DIP SWITCHES 2 AND 3 ON THE TCOO900 AND 3 AND 4 ON THE RCOO900P TO THE SAME SETTINGS. RCOO900P TCOO900 DIP DIP ON ON OFF OFF N° DIP Function N° DIP 1 2 Freq / 3 Freq 2 Buzzer ON / OFF Frequency channel selection Function 1 Low power. (see Section E on page 9) Frequency channel selection 5 Out1 type: N.O. contact (OFF) or 10k signal (ON) 1 6 Out2 type: N.O. contact (OFF) or 10k signal (ON) 2 It is possible to associate a maximum of 8 TCOO900 to each RCOO900P. Frequency channel selection WARNING: for a correct functioning of the system, every TCOO900 must have the frequency dip switch set the same way as the corresponding RCOO900P. Channel Dip 3 (2) Dip 4 (3) Frequency OFF OFF 912.900 OFF ON 914.900 ON OFF 916.900 ON ON 918.900 On a safety system with more than one Receiver, to avoid interference, we recommend the use of different frequency settings on each set of a RCOO900P and the associated TCOO900. 1.5V POWER THE TCOO900 BY INSTALLING THE TWO AA BATTERIES (1.5V) INTO THE BATTERY HOLDER. PLEASE NOTE THE CORRECT POLARITY. 1.5V STEP 4 STEP 5 MOUNT THE TCOO900 AS HIGH AS POSSIBLE AND IN SUCH A WAY AS THERE ARE NO OBSTACLES IN THE DIRECTION OF THE RCOO900P AND IN SUCH A WAY AS THE MAXIMUM DISTANCE BETWEEN THE TWO DEVICES IS LESS THAN 60 FEET (MAX 20 METERS / 60 FEET). Height min: 8” WARNING: install the TCOO900 at a minimum height of 8” from the ground. Keep the installation area clean of debris which can effect the normal operation of the system. NOTE: Transmitter Solutions is not responsible for any damage caused by an improper, incorrect, or unintended use of the product. Height min: 8” STEP 6 MOUNT THE RCOO900P AS CLOSE AS POSSIBLE TO THE TCOO900. IF MOUNTED TO A WALL, USE SUITABLE SCREWS AND ANCHORS TO SECURE THE RCOO900P. STEP 7 DEPENDING ON THE TYPE OF SIGNAL REQUIRED, CONNECT THE OUTPUTS AS EXPLAINED IN THE FOLLOWING EXAMPLES. WARNING: The power supply for the receiver must be an insulated transformer to protect against short circuits NOTE: The signals given on the outputs 1 and 2 are a N.O. contact, resistive output (10kΩ) or pulsed output, depending on the setting of dip switches 5 and 6, and the wiring connection. NOTE: The level of acoustic noise generated by the device is less than 70 dBA. EXAMPLE 1 - Pulsed 2 Frequency on both channels EXAMPLE 2 - Pulsed 2-wire on channel 1 and pulsed 4-wire on channel 2 RCO900P OFF ON RCO900P OFF ON Buzzer 2Freq/3Freq Buzzer OFF Buzzer 2Freq/3Freq Buzzer OFF Frequency Frequency Out1 - 10k Out1 - 10k Out2 - 10k Out2 - 10k Programming/ Reset key Programming/ Reset key + - + not connected 12/24 Vac/Vdc operator 1 pulsed input 12/24Vdc Power / Signal Operator 1 2-wire pulsed operator 2 pulsed input Signal Power Operator 2 4-wire pulsed EXAMPLE 3 - Pulsed 4-wire on both channels EXAMPLE 4 - Pulsed 3-wire on both channels RCO900P OFF ON RCO900P OFF ON Buzzer Buzzer 2Freq/3Freq Buzzer OFF 2Freq/3Freq Buzzer OFF Frequency Frequency Out1 - 10k Out1 - 10k Out2 - 10k Out2 - 10k Programming/ Reset key Programming/ Reset key + - + not connected 12/24 Vac/Vdc Signal Power Operator 1 4-wire pulsed Signal POWER COM Power Operator 2 4-wire pulsed Signal 12/24 Vac/Vdc Operator 2 3-wire pulsed EXAMPLE 6 - Pulsed 4-wire on channel 1 and N.O. on channel 2 RCO900P RCO900P OFF ON Buzzer Buzzer 2Freq/3Freq Buzzer OFF 2Freq/3Freq Buzzer OFF Frequency Frequency Out1 - 10k Out1 - 10k Out2 - 10k Out2 - 10k Programming/ Reset key Programming/ Reset key + - Power / Signal 12/24Vdc Operator 1 2-wire pulsed POWER COM Operator 1 3-wire pulsed EXAMPLE 5 - Pulsed 2-wire on channel 1 and 10k on channel 2 OFF ON Signal 12/24 Vac/Vdc + - Resistive input 10k Operator 2 10k Power Signal 12/24 Vdc/Vac Operator 1 4-wire pulsed STEP 8 N.O. contact input Operator 2 N.O. STEP 9 MOUNT THE IGAZE REP RCOO900P POWER THE RCOO900P WITH 12-24 VAC/DC INSULATED POWER SUPPLY (NOT INCLUDED WITH THE IGAZE® REP KIT). ® C PROGRAMMING STEP 10 PROGRAM THE TCOO900 TO THE RCOO900P ACCORDING TO THE FOLLOWING INSTRUCTIONS: PROGRAMMING OF THE MOVABLE DEVICE ON CHANNEL 1 OUTPUT OF THE FIXED DEVICE Check that the DIP 2 and 3 of the TCOO900 and DIP 3 and 4 of the RCOO900P are set the same way. Press and keep pressed the programming/ reset button on the RCOO900P. Release the programming/reset button on the RCOO900P Press and keep pressed the programming/reset button on the TCOO900 relative to the used input. Prog./Test1 for safety edge 1, Prog/Test2 for safety edge 2. RCOO900P emits 2 BEEPS. (*) Release the programming/reset button on the TCOO900. Programming has succeeded RCOO900P emits 1 BEEP. To enter more TCOO900 in the RCOO900P, repeat the operation from step 2. (on page 3) (*) If you hear 4 BEEPS, it means that the maximum number of safety edges for the selected channel has been reached and that no new devices on the same channel output can be memorized. NOTE: When the TCOO900 is used with two connected safety edges, it is necessary to carry out the learning process two times, one for each input. WARNING: The same output of the TCOO900 can be memorized on both output channels. To erase the memorized input it is necessary to perform a complete reset of the RCOO900P (see page 8). PROGRAMMING OF THE TRANSMITTER ON CHANNEL 2 OUTPUT OF THE FIXED DEVICE Check that the DIP 4 and 5 of the TCOO900 and DIP 3 and 4 of the RCOO900P are set the same way. Press and keep pressed the programming/ reset button on the RCOO900P. Release the programming/reset button on the RCOO900P Press and keep pressed the programming/reset button on the TCOO900 relative to the used input. Prog./Test1 for safety edge 1, Prog/Test2 for safety edge 2. RCOO900P emits 2 BEEPS. (*) Release the programming/reset button on the TCOO900. Programming has succeeded RCOO900P emits 1 BEEP. RCOO900P emits 2 BEEPS. To enter more TCOO900 in the RCOO900P, repeat the operation from step 2. (on page 3) (*) If you hear 4 BEEPS, it means that the maximum number of safety edges for the selected channel has been reached and that no new devices on the same channel output can be memorized. NOTE: When the TCOO900 is used with two connected safety edges, it is necessary to carry out the learning process two times, one for each input. WARNING: The same output of the TCOO900 can be memorized on both RCOO900P output channels. To erase the memorized input it is necessary to perform a complete reset of the RCOO900P (see page 8). STEP 11 TEST THAT THE PROGRAMMING OF THE MOVABLE DEVICE WAS SUCCESSFUL. On each TCOO900, two buttons, labeled “programming/test key”, and two leds are present. Pushing the programming button of the edge to test during normal functioning (so not in programming) produces a signal that is sent to the RCOO900P activates the output channel and responds to this signal with: Acoustic signaling during the normal functioning Number of BEEP/ BLINK Meaning What to do Regular functioning, no mistake found. One or more safety edges faulty. Check the safety edge connections One or more 8.2k / 10k resistive edges disconnected. Check the resistive edges connected Battery level low. Substitute the batteries of the indicted device Low battery. Replace the batteries One or more associated devices disconnected Check each associated device NOTE: If one TCOO900 is in the alarm state and it is necessary to open or close the operating device, press and keep pressed the programming / test button of the TCOO900 in alarm at the same time the operating device is activated to open or close. STEP 12 VERIFY THE CORRECT FUNCTION OF EACH SAFETY EDGE, MOVABLE AND FIXED DEVICES WITH THE OPERATOR INSTALLED. RECEIVER RESET Using the program/reset key, it is possible to erase all TCOO900 that are programmed into the RCOO900P. NOTE: This proceedure resets all memory to factory defaults. Press and keep pressed the programming / reset button on the RCOO900P. RCOO900P emits 1 BEEP DO NOT RELEASE the programming/reset button on the RCOO900P. RCOO900P emits 2 BEEPS DO NOT RELEASE the programming/reset button on the RCOO900P. RCOO900P emits a series of rapid BEEPS. DO NOT RELEASE the programming/reset button on the RCOO900P. RCOO900P emits a continuous BEEP Release the programming/reset button on the RCOO900P RCOO900P emits 6 BEEPS. The reset is complete. E ENERGY SAVING (LOW POWER) With the dip switch set to low power it is important to remember that the TCOO900 will only check in with the RCOO900P every 15 seconds. If a power failure (dead battery) were to occur during this 15 second interval, the RCOO900P will only signal an alarm after the 15 second interval has been reached. TCOO900 Dip switch 1 set ON: (Low power activated) state of the transmitter is checked every 15 seconds. TCOO900 Dip switch 1 set OFF: (Low power deactivated) state of the transmitter is checked each second. FCC COMPLIANCE FCC ID: SU7TCO900 and SU7RCOO900P This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. G TROUBLESHOOTING 1 – Ensure that wire leads from safety edge are securely attached to the movable device (TCOO900). NOTE: Wire leads from safety edge have no specific polarity and can be placed in either terminal of Safety device Input1 or Safety device Input2 on the movable device. Ensure that wire leads into the fixed device (RCOO900P) are firmly connected and into proper terminals (ie N.C. or N.O.) for help in wiring RCOO900P inputs see STEP 7 examples. 2 – Make sure that the type of safety edge attached to the TCOO900 is resistive. How to determine the type of edge if there is no clear label: A voltmeter can be used to determine the type of edge: 1- Set voltmeter to read Ohms 2- Place a test probe on each of the wire leads from the safety edge 3- If the voltmeter registers resistance (ie 8.2KΩ or 10KΩ) the safety edge is resistive 4- If the voltmeter does not register resistance (ie 1) the safety edge is mechanical If safety edge is mechanical, the system RCOO900P / TCOO900 is NOT compatible. Determine what type of output signal the gate operator is looking for: • • • • Doorking – 10K resistive device NICE – 8.2K resistive device If 8.2k or 10k (resistive): DIP switch 5 or 6 on the RCOO900P need to be in the ON position (DIP 5 for Output1 and Safety Device 1 and DIP 6 for Output2 and Safety Device 2) If N.O. contact: DIP switch 5 or 6 on the RCOO900P needs to be in the off position (DIP 5 for Output1 and Safety Device 1 and DIP 6 for Output2 and Safety Device 2) 3 – To ensure that the TCOO900 and RCOO900P are communicating within the same frequency DIP switch 2 and 3 on the TCOO900 and DIP switch 3 and 4 on the RCOO900P need to be in the same position. 4 – Check batteries in TCOO900 to ensure correct polarity and sufficient power. 5 – If TCOO900 and RCOO900P are still not communicating ensure that obstacles between the devices are moved and mount devices as high as possible and away from metal objects. 10 WARRANTY The warranty period of this product is 24 months, beginning from the manufacturing date. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. This warranty does not extend to the product casing which can be damaged by conditions outside of the control of Transmitter Solutions. EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS. 11 2 480 South 3850 West, Suite Salt Lake City, UT 84120 (866) 975-0101 • (866) 975-0404 fa www.transmittersolutions.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Create Date : 2018:05:24 10:59:47+02:00 Metadata Date : 2018:06:12 16:05:08+08:00 Modify Date : 2018:06:12 16:05:08+08:00 Creator Tool : Adobe InDesign CS5.5 (7.5.3) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 7281 bytes, use -b option to extract), (Binary data 9779 bytes, use -b option to extract) Instance ID : uuid:536e90ae-b7dc-4c4a-8ed8-52cb445c957c Original Document ID : xmp.did:b06ba49a-3f07-4a52-8a68-66ad89614606 Document ID : xmp.did:6647D3E9D74DE8119E34D1992698846B Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:b06ba49a-3f07-4a52-8a68-66ad89614606, xmp.iid:0c53bc28-19fd-4731-9488-98bd78fd314a, xmp.iid:f32dcbdd-3ecb-4971-a5f6-794e1f4fc88f, xmp.iid:dc720aec-1b56-4a80-a8fa-07e6dd74d261, xmp.iid:f42c4173-ab1e-4b58-afb1-8f0b8eff8cc1, xmp.iid:9DE4F5EC6239E8119DFEA6AD43E6EF64, xmp.iid:9EE4F5EC6239E8119DFEA6AD43E6EF64, xmp.iid:9FE4F5EC6239E8119DFEA6AD43E6EF64, xmp.iid:027CA13C6839E8119DFEA6AD43E6EF64, xmp.iid:221BBBB46A39E8119DFEA6AD43E6EF64, xmp.iid:0028E5106B39E8119DFEA6AD43E6EF64, xmp.iid:29FDC4096F39E8119DFEA6AD43E6EF64, xmp.iid:2F9942437039E8119DFEA6AD43E6EF64, xmp.iid:FF3F34487239E8119DFEA6AD43E6EF64, xmp.iid:DA5CA4D47539E8119DFEA6AD43E6EF64, xmp.iid:2BF5F9E07639E8119DFEA6AD43E6EF64, xmp.iid:6E0C2DFB7639E8119DFEA6AD43E6EF64, xmp.iid:7ECC27748F39E8119DFEA6AD43E6EF64, xmp.iid:09EAF4EE9B39E811B87985EA183BD7C6, xmp.iid:12A4B7A69E39E811B87985EA183BD7C6, xmp.iid:C3E0289E9F39E811B87985EA183BD7C6, xmp.iid:AD22B0EDA139E811B87985EA183BD7C6, xmp.iid:8989E266A339E811B87985EA183BD7C6, xmp.iid:7F3B3B59AA39E81187CDB7F06FB192A2, xmp.iid:803B3B59AA39E81187CDB7F06FB192A2, xmp.iid:3152DA65AA39E81187CDB7F06FB192A2, xmp.iid:2E964499AE39E81187CDB7F06FB192A2, xmp.iid:4FBAE890AF39E81187CDB7F06FB192A2, xmp.iid:08D43160BE3BE81188079974CB9C399C, xmp.iid:AACE9BB8C33BE81188079974CB9C399C, xmp.iid:C7561FF9C33BE81188079974CB9C399C, xmp.iid:4C419F6EC73BE81188079974CB9C399C, xmp.iid:47F1846CCD3BE81188079974CB9C399C, xmp.iid:248A9598CD3BE81188079974CB9C399C, xmp.iid:4A9C20E1CE3BE81188079974CB9C399C, xmp.iid:F43488EACE3BE81188079974CB9C399C, xmp.iid:D9713E36CF3BE81188079974CB9C399C, xmp.iid:08D3E93ED33BE81188079974CB9C399C, xmp.iid:9E2A8580D33BE81188079974CB9C399C, xmp.iid:830A3665D43BE811AB23E0E336FD05EC, xmp.iid:A6F4E1C2D43BE811AB23E0E336FD05EC, xmp.iid:E02BDD1FD53BE811AB23E0E336FD05EC, xmp.iid:AEEE5091D53BE811AB23E0E336FD05EC, xmp.iid:D38E4436D93BE811B077DE4B47BC4B0D, xmp.iid:226F11FADC3BE811B077DE4B47BC4B0D, xmp.iid:D171DD96DE3BE811B077DE4B47BC4B0D, xmp.iid:20FDD3B1EC3BE811B077DE4B47BC4B0D, xmp.iid:3C6E4A31ED3BE811B077DE4B47BC4B0D, xmp.iid:D1009667ED3BE811B077DE4B47BC4B0D, xmp.iid:D2009667ED3BE811B077DE4B47BC4B0D, xmp.iid:0AAE1F71EE3BE811B077DE4B47BC4B0D, xmp.iid:BCF69608EF3BE811B077DE4B47BC4B0D, xmp.iid:9D7742CDF13BE811B077DE4B47BC4B0D, xmp.iid:3F4CA23FF33BE811B077DE4B47BC4B0D, xmp.iid:89ED6763F33BE811B077DE4B47BC4B0D, xmp.iid:E1383BC3F33BE811B077DE4B47BC4B0D, xmp.iid:EC0E8CDAF43BE811B077DE4B47BC4B0D, xmp.iid:01D02E05F53BE811B077DE4B47BC4B0D, xmp.iid:F54F269FF63BE811B077DE4B47BC4B0D, xmp.iid:C492471AF73BE811B077DE4B47BC4B0D, xmp.iid:E4D1755EF73BE811B077DE4B47BC4B0D, xmp.iid:098CC07FF73BE811B077DE4B47BC4B0D, xmp.iid:7B5C1400F83BE811B077DE4B47BC4B0D, xmp.iid:5E111D00F83BE811B077DE4B47BC4B0D, xmp.iid:74655C1CFA3BE811AE7AB893BE8B81FA, xmp.iid:AB0E4B3DFA3BE811AE7AB893BE8B81FA, xmp.iid:2E4C689AFB3BE811871CEFEDAF80E1E0, xmp.iid:2F4C689AFB3BE811871CEFEDAF80E1E0, xmp.iid:1E3241D1013CE811871CEFEDAF80E1E0, xmp.iid:73632425083CE811871CEFEDAF80E1E0, xmp.iid:A759FD30083CE811871CEFEDAF80E1E0, xmp.iid:7C258DB7083CE811871CEFEDAF80E1E0, xmp.iid:4038DF350A3CE811871CEFEDAF80E1E0, xmp.iid:FAD376990A3CE811871CEFEDAF80E1E0, xmp.iid:174526D00A3CE811871CEFEDAF80E1E0, xmp.iid:EA93B92A0B3CE811871CEFEDAF80E1E0, xmp.iid:B6335F750B3CE811871CEFEDAF80E1E0, xmp.iid:C6F051F89A3CE81181E6A4683A452E1E, xmp.iid:B20267A89B3CE81181E6A4683A452E1E, xmp.iid:181D4ED09B3CE81181E6A4683A452E1E, xmp.iid:443CF6E0A13CE81181E6A4683A452E1E, xmp.iid:059E0ADDBA3CE81181E6A4683A452E1E, xmp.iid:33B0270CC13CE81181E6A4683A452E1E, xmp.iid:50DF0A58C13CE81181E6A4683A452E1E, xmp.iid:07BB5A77C33CE81181E6A4683A452E1E, xmp.iid:981F6E89C33CE81181E6A4683A452E1E, xmp.iid:3B37C6CAC33CE81181E6A4683A452E1E, xmp.iid:C8F8F800CF3CE811A0FFF100D79DAD30, xmp.iid:6F953F1A4F3DE811B99EE47674F3C816, xmp.iid:DBEB21E45F3DE81180B1C90CE42607BE, xmp.iid:18BA339D673DE81180B1C90CE42607BE, xmp.iid:280948DCD74DE8119E34D1992698846B, xmp.iid:290948DCD74DE8119E34D1992698846B, xmp.iid:6647D3E9D74DE8119E34D1992698846B, xmp.iid:94EF84B4D94DE8119E34D1992698846B, xmp.iid:EA7EF1AB9252E8118A4CFCEB617C7B91, xmp.iid:F1AD37CB305FE811ABFEDC5635727003 History When : 2018:04:05 10:16:05-06:00, 2018:04:05 10:41:52-06:00, 2018:04:05 10:41:52-06:00, 2018:04:05 10:44:26-06:00, 2018:04:05 11:43:24-06:00, 2018:04:06 08:22:47+02:00, 2018:04:06 08:22:48+02:00, 2018:04:06 09:00:49+02:00, 2018:04:06 09:00:49+02:00, 2018:04:06 09:18:29+02:00, 2018:04:06 09:21:04+02:00, 2018:04:06 09:49:30+02:00, 2018:04:06 09:58:16+02:00, 2018:04:06 10:12:43+02:00, 2018:04:06 10:38:07+02:00, 2018:04:06 10:45:37+02:00, 2018:04:06 10:46:21+02:00, 2018:04:06 13:41:32+02:00, 2018:04:06 15:10:52+02:00, 2018:04:06 15:30:19+02:00, 2018:04:06 15:37:15+02:00, 2018:04:06 15:53:47+02:00, 2018:04:06 16:04:20+02:00, 2018:04:06 16:54:03+02:00, 2018:04:06 16:54:25+02:00, 2018:04:06 16:54:25+02:00, 2018:04:06 17:24:29+02:00, 2018:04:06 17:31:24+02:00, 2018:04:09 08:22:27+02:00, 2018:04:09 09:00:43+02:00, 2018:04:09 09:02:31+02:00, 2018:04:09 09:27:17+02:00, 2018:04:09 10:10:10+02:00, 2018:04:09 10:11:24+02:00, 2018:04:09 10:20:36+02:00, 2018:04:09 10:20:51+02:00, 2018:04:09 10:22:58+02:00, 2018:04:09 10:51:51+02:00, 2018:04:09 10:53:41+02:00, 2018:04:09 11:00:05+02:00, 2018:04:09 11:02:42+02:00, 2018:04:09 11:05:18+02:00, 2018:04:09 11:08:28+02:00, 2018:04:09 11:34:33+02:00, 2018:04:09 12:01:30+02:00, 2018:04:09 12:13:03+02:00, 2018:04:09 13:54:01+02:00, 2018:04:09 13:57:35+02:00, 2018:04:09 13:59:06+02:00, 2018:04:09 14:02:52+02:00, 2018:04:09 14:06:32+02:00, 2018:04:09 14:10:46+02:00, 2018:04:09 14:30:35+02:00, 2018:04:09 14:40:56+02:00, 2018:04:09 14:41:56+02:00, 2018:04:09 14:44:37+02:00, 2018:04:09 14:52:25+02:00, 2018:04:09 14:53:37+02:00, 2018:04:09 15:05:05+02:00, 2018:04:09 15:08:31+02:00, 2018:04:09 15:10:26+02:00, 2018:04:09 15:11:22+02:00, 2018:04:09 15:14:57+02:00, 2018:04:09 15:14:57+02:00, 2018:04:09 15:30:03+02:00, 2018:04:09 15:30:59+02:00, 2018:04:09 15:40:44+02:00, 2018:04:09 15:48:51+02:00, 2018:04:09 16:25:13+02:00, 2018:04:09 17:10:31+02:00, 2018:04:09 17:10:51+02:00, 2018:04:09 17:14:37+02:00, 2018:04:09 17:25:18+02:00, 2018:04:09 17:28:05+02:00, 2018:04:09 17:29:37+02:00, 2018:04:09 17:32:09+02:00, 2018:04:09 17:34:14+02:00, 2018:04:10 10:41:32+02:00, 2018:04:10 10:46:27+02:00, 2018:04:10 10:47:34+02:00, 2018:04:10 11:30:59+02:00, 2018:04:10 14:29:50+02:00, 2018:04:10 15:14:06+02:00, 2018:04:10 15:16:13+02:00, 2018:04:10 15:31:25+02:00, 2018:04:10 15:31:55+02:00, 2018:04:10 15:33:45+02:00, 2018:04:10 16:54+02:00, 2018:04:11 08:10:58+02:00, 2018:04:11 10:11:09+02:00, 2018:04:11 11:06:26+02:00, 2018:05:02 09:10:14+02:00, 2018:05:02 09:10:37+02:00, 2018:05:02 09:10:37+02:00, 2018:05:02 09:23:26+02:00, 2018:05:08 09:37:33+02:00, 2018:05:24 10:59:40+02:00 History Software Agent : Adobe InDesign CC 13.1 (Macintosh), Adobe InDesign CC 13.1 (Macintosh), Adobe InDesign CC 13.1 (Macintosh), Adobe InDesign CC 13.1 (Macintosh), Adobe InDesign CC 13.1 (Macintosh), Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /, /metadata, /, /, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Derived From Instance ID : xmp.iid:290948DCD74DE8119E34D1992698846B Derived From Document ID : xmp.did:5E111D00F83BE811B077DE4B47BC4B0D Derived From Original Document ID: xmp.did:b06ba49a-3f07-4a52-8a68-66ad89614606 Derived From Rendition Class : default Doc Change Count : 5467 Key Stamp Mp : AAAAAA== Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 12 Creator : Adobe InDesign CS5.5 (7.5.3)EXIF Metadata provided by EXIF.tools