Controlled Entry Distributors REATSHE CARD READER User Manual

Controlled Entry Distributors, Inc. CARD READER Users Manual

Users Manual

I/OALARM-R8R20Q6Lock Interface Principle:By programme setting, I/O switch between low level and high level.4-low level5-high levelI/OL-L++12VR7 R19Q2D6Alarm Interface Principle:when alarm, the I/O outputs high level.The W2 is fully waterproof Proximity stand alone access Reader, which uses advanced microprocessor, equipped with large capacity Flash memory, supports up to 10 000 cards. It is so easy to add or delete card users by using the master card, besides, with Infrared remote control programmer, the user can set the features by themselves, including Alarm, Self-protection, interlock and Anti-submarine back Function. In additional, with infrared remote control programmer, you can add or delete cards directly by inputting card numberThe W2 not only has the features of low power consumption, automatic selection of lock ,anti vandal alarm and exit button, but also has the protective functions against input over voltage and outputs short-circuit. These features make the W2 safe , reliable and easy in operation. It is an idea choice for door access.2.DescriptionStandalone Card ReaderUse capacity: 10,000 Card interface: 125KHZ EM cardRemote control for programmingWith Manager cards for fast add and delete usersWiegand26 input/output3.Features4. Specifications Supply VoltageSleeping CurrentCard typeCard Reading DistanceWiegand interfaceTemperature20% 98%Max20AMax20ATwo103*48*23mmDrill holes on the wall or prepare the cassette.Wire through the hole, and blanket the unused cable in case of short circuit.Fix the back cover firmly on the cassette or the wall.Attach the reader to the back cover.5. Installation6. WiringNo12345678910 Color Yellow Blue Brown Purple Grey Red Black White Green Orange Function D0 D1 ALARM+ OPEN D_IN 12V GND VSS L- L+/Alarm+ DescriptionWiegand output, input signal wire D0 Wiegand output, input signal wire D1connecting to the negative pole of the alarm equipment To connect to one part of Exit ButtonDoor Contact input(+) 12Vdc Positive Regulated Power Input(-) Negative Regulated Power Input the negative pole of the controller, connect to the other part of Exit button and door contactConnect to the negative pole of the LockConnect to the positive pole of the lock and alarm equipmentConnection Diagram7. Interface Circuits Figure 1Note: The above diagrams show the output interface circuits. Do not power on until all wiring has been completedPower off, use the supplied Contact Pin to short out the 2P socket on the mainboard, then power on, if successful, the beeper will beep twice, the LED shines in orange, remove the Short Pin, then read any two EM cards, after that the LED turns in red, means reset to factory default setting successfully. Of the two EM cards read, the first one is Manager add card, the second one is Manager delete card.Remarks: Reset to factory default setting, the users' information enrolled is still retained. When reset to Factory setting, the two Manager cards must be re-enrolled.8.To Reset to Factory Default and Manager Card setting9. Sound and Light indicationOperation status Reset to factory default settingSleeping mode Operation successfulEnter into programming modeEnter into setting Exist from programming modeOperation failed Open the doorAlarmLEDOrangeRed shines slowRed shinesOrange shinesRed shines slowGreen shinesRed shines fastBuzzerTwo short ringShort ringShort ringShort ringShort ringThree short ringShort ringAlarm10. W2 Detailed Programming Guide 10.1User settingsThere are 2 ways to add and delete users:A - By manager card; B - By remote control A - By Manager card(The most convenient way)To Delete User by Manager CardB- By Remote controlEnter into the programming mode firstlyTo Enter the programming modeManager add card Read user card Manager add card Cards can be added continuously.Manager delete card Read user card Manager Delete ca rd Cards can be deleted continuously.* Manager Password # 888888 is the default factory master codeTo Add user by Manager CardRemarks: All the steps below must be done after enter into programming modeTo change the master code 0 New Password # Repeat New Password #The master code must be 6 8 digit number.To add a card user (Method 1) This is the faster way to enter cards using ID number auto generation. The card can be either be presented or input the 8 digit card number from the card can be manually entered1 Read Card # or1 Input Card number (8 digit) # Card can be added continuously without exiting programming mode. The card number is the last 8 digits of the number printing on the card.DC12V/3A+--+Lock-+Exit buttonAlarmdoor detecting switch Common Power SupplyW2D0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangeD0ALARM-OPEND_IN+12VGNDVSSL+ ALARM+J1DC12V/3A+-COMNC NOPUSHD1L-GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangedoor detecting switch Exit buttonAlarmFail-securelockFail-safe lockSpecial Power SupplyW2 - Waterproof Standalone Proximity ReaderShielded cablesCD61mm95.5mm40mmABTo add a card user(Method 2)This is the alternative way to enter cards using User ID Allocation. In this method a User ID is allocated to a card. Only one user ID can be allocated to a single card.1 ID number # Read Card # or1 ID number # the Card number (8 digits) #To delete a card user by card Number. Note users can be deleted continuously without exiting programming mode2 Read Card # or2 Card number # To delete ALL users.(Note: This option will delete all users but Manager Cards. Be careful with use) 2 0000 # .4. .5. .6.Can be used as salve reader2 pcsW2 can be interconnected/ interlockedCan be used as controller by connection slave readerAnti-submarine back FunctionAlarm signal output, Door open detectionFull of 10000 users, recognizing speed <15ms. 1. Packing ListNameStandalone Proximity ReaderInfrared remote controlManager cardShort PinUser manualSelf Tapping ScrewsSpecification W2One for add, one for deleteUsed for factory default settingW23.5*27mmQuantity112114/2HumidityLock output load Alarm output load Manager cardDimensionsDC12V 10%<15mA125KHZ EM card5 10cmWiegand 26-20 60.1. .2. .3.
10.2 Door settingFail secure (Unlocked when power on) 4 0 99 #0-99 is to set the door relay time 0-99 seconds.Fail safe (unlocked when power is off)This is the factory default, 5 seconds:5 0 99 #0-99 is to set the door relay time 0-99 seconds.Door open detectionDoor Open Too Long (DOTL) warning. When used with an optional magneticcontact or built-in magnetic contact of the lock, if the door is opened normally, butnot closed after 1 minute, the inside buzzer will beep automatically to remindpeople to close the door and continue for 1 minute before switching offautomatically.Door Forced Open warning. When used with an optional magnetic contact or built in magnetic contact of the lock, if the door is forced open, or if the door is opened after 120 seconds of the electro-mechanical lock not closed properly, the inside buzzer and alarm output will both operate. To disable door open detection.(Factory default) 6 0 # Security Mode SettingRead er Lockout & Alarm Output options. If there are 10 invalid cards in a 10 minute period, the Reader will lockout for 10 minutes or the alarm will operate for 10 minutes, depending on the option selected below.Normal status (No lockout or alarm) 7 0 # (Factory default setting)Reader LockoutTo Unlock the door7 1 # Alarm Output 7 2 # Door Interlock.Door interlock disabledDoor interlock enabled8 0 # 8 1 # Alarm output timeTo set the alarm output time (0-3minutes) Factory default is 1 minute 9 0~3 # To remove the alarmTo remove the door forced open warning Read valid card or Master Code #To remove the door open too long warningClose the door or Read valid card or Master Code #Read user card (Note that Manager Card can't be used to unlock the door.) Attach: Advanced Application1. W2 operating as a ControllerIn this mode the W2 supports a Wiegand 26 bit input so an external Wiegand device with a 26 bit output can be connected to the Wiegand input terminals on the W2. Either an ID card reader (125 KHZ) or an IC card reader (13.56MHZ) can be connected to the W2. Cards are required to be added at the external reader, except where an external EM reader is used, in this case cards can be added at either reader. See figure 1figure 1D0D1+12VGND-+Lock-+Em cardHID cardIc cardDC12V/3A+-PowerD0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangewiegand reader reader plugW2 controller Alarm Exit buttondoor detecting switch 2. W2 operating as a Wiegand Output ReaderIn this mode the W2 supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any controller which supports a Wiegand 26 bit input. See figure 2ALARM+J1WhiteGreyYellowBrownRedBlackBluePurpleOrangeD0D1W2+-Powerful supply Controller with wiegand 26 input+12VGNDControllerGreen D0D1ALARM-OPEND_IN+12VGNDVSSL-L+ figure 23. Two W2 units interconnected for a single doorIn this mode two W2 units are used for a single door, one for entry and the other for exit.Either device acts as the controller and reader at the same time. Users can be enrolled oneither of the devices. In this mode the user capacity for one door can be up to 20000. The setting of the two W2 units must be the same including the master code. See figure 3Exit button-+Lockdoor detecting switch-+AlarmDC12V/3A+-Powerindoor outdoorD0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangeD0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangeW2 controller 2W2 controller 1figure 34. Two W2 units interconnected & interlocked for 2 doorsIn this mode two W2 units are used for a two doors which are then interconnected and interlocked. In this mode the doors can be interlocked so that when door 1 is open, door 2 cannot be opened, and vise versa. The interlocked function is mainly used in banks, prisons, and other places where a higher level of security is required. See figure 4door detecting switch 1--++Lock 1-+-+DC12V/3A+-PowerW2 controller 2Door 2Alarm 2Alarm 1Lock 2Exit button 1door detecting switch 2Exit button 2Door 1W2 controller 1D0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangeD0D1ALARM-OPEND_IN+12VGNDVSSL-L+ ALARM+J1GreenWhiteGreyYellowBrownRedBlackBluePurpleOrangefigure 45. Anti-submarine function for single door (3 1 #)The connection diagram is as figure 1. Install one Wiegand reader (or a W2 without user information as reader) outside the door, connecting to one W2-Controller inside the door, which acts as the Anti-submarine Master unit. Of the two devices, they build up an anti-submarine system for single door. The operation and function is as below:5.1 Set the needed function and enroll the User Cards on the inside W2 - Anti-submarine Master unit. 5.2 With the valid user card, the user can only enter the door from the outside reader, and exit from the inside W2 Controller. On the other hand, without entering record from the reader, the user can't exit from the controller inside, also, the user can't enter in and exit twice continuously. 6. Anti-submarine function for 2 doors The connection diagram is as Figure 4. Door 1 with one W2, and Door 2 with one W2, set one W2 on Door 1 as the Anti-submarine Auxiliary unit (3 2 #), and set the other W2 on Door 2 as the Anti-submarine Master unit(3 1 #). They build up a two doors anti-submarine system, which is normally used for parking lot......etcThe operation and function is as below:6.1 Set the needed function and enroll the User Cards from W2 - Anti-submarine Master unit on Door 2. 6.2 With the valid user card, the user can only enter in from Door 1, and exit from Door 2. On the other hand, without entering record from the Auxiliary unit, the user can't exit from the Master unit or Auxiliary unit , also, the user can't enter in and exit twice continuously. .9. .10. .11..6. .7. .8.Lock Power SettingAnti-submarine SettingsAnti-submarine DisabledAnti-submarine Master Mode:Antisubmarine Auxiliary Mode(Note: the detailed wiring diagram and illustrate,please refer to the Advanced application ) . (Factory default)3 0 #3 1 #3 2 #To enable door open detection 6 1 # To Unlock the door
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. NOTE 2: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Navigation menu