Controlled Entry Distributors T3PLUS Transmitter Solutions User Manual

Controlled Entry Distributors, Inc. Transmitter Solutions Users Manual

Users Manual

1/46-1621768 rev00 02/03/2016The Transmitter Solutions - T3 PLUS transmitter is a key chain style mini transmitter operating at 433,92 MHz. It has been designed for the control of automatic closing systems and anti-burglar systems, thanks to its very high security coding system (KeeLoq® Hopping code).The code sent by the transmitter changes at each activation, avoiding any scanning and copying risk. A special algorithm allows to keep synchronized transmitter and receiver.The CR2032 battery of the transmitter have a shelf life of about 24 months.The product fully complies with Part 15 of FCC Regulations.3 CHANNELS TRANSMITTERT3 PLUSThank you for choosing this Transmitter Solutions product.Please read this manual carefully before installing the product.CONTENTS1. TRANSMITTER OVERVIEW1A - General information1B - Technical specication1C - Main components2. NUMBERING3. PROGRAMMING4. OPERATION5. BATTERY ACCESS6. TROUBLESHOOTING1A - General information
2/4 6-1621768 rev00 02/03/20161B - Technical specicationsOperating frequency:Number of keys:Battery:Battery life:Security Code:Number combinations:Operating temperature:Overall dimensions:Weight:433,92 MHz33V lithium battery CR203218 - 24 monthsKEELOQ® Hopping code2exp6423°F - +131°F (-5°C - +55°C)2.46’’ x 1.26’’ x 0.39’’ (62.4 x 32 x 10 mm)0.55 oz. (15.5gr.)1C - Main componentsHidden keyKeyringholderKey 1Red LEDKey 2Key 3Screw
3/46-1621768 rev00 02/03/20162 - NUMBERINGEach transmitter is manufactured and sold with a different factory-set serial number.3 - PROGRAMMINGThe transmitter must be programmed into your system memory.Your own installer or reseller will provide you the necessary instructions for your system.4 - OPERATIONA- Firmly depress the button until the red LED illuminates.B- After the LED has illuminated, release the button.If the device you are attempting to activate does not respond, repeat steps A and B or consult section 6 ( Troubleshooting ) of this manual.5 - BATTERY ACCESSTo access the battery, remove the rear screw with a screwdriver and open the case.Slide out the old battery and replace them with the new ones [CR2032] respecting the polarity, with the positive (+) side upward.NOTE: Please dispose of the batteries properly according to local laws and regulations.Test proper battery installation by verifying that the red LED illuminates when the button is pushed.6 - TROUBLESHOOTINGPROBLEM SOLUTIONThe system does not receiver the transmitter signal.The transmitter LED will not lightReplace the transmitterbatteriesThe system does not receiver the transmitter signal.The transmitter LED is ONCheck to verify the transmitter is programmed into your sistemThe operating range is reduced Replace the transmitterbatteries
4/4 6-1621768 rev00 02/03/2016Transmitter Solutions - Type: T3 PLUSFCC ID: SU7T3PLUSThis device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.The warranty period of Transmitter Solutions 433 transmitters is 60 months, beginning from the manufacturing date of the transmitter. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Transmitter Solutions. The warranty does not extend to the transmitter case which can be damaged by conditions outside the control of Transmitter Solutions or to battery life.NOTICEWARRANTYAny changes or modication to Transmitter Solutions equipment not expressly approved by Transmitter Solutions could void the manufacturer’s warranty and the user’s authority to operate this product.7380 S. Eastern Ave, Ste 124-320 - Las Vegas, NV 89123(866) 975-0101 - (866) 975-0404 Faxwww.transmittersolutions.com

Navigation menu