Controlled Entry Distributors TRADCS433 Community Controls Handicap Plate Transmitter User Manual TS small receiver pg1

Controlled Entry Distributors, Inc. Community Controls Handicap Plate Transmitter TS small receiver pg1

user manual

Extra-Small Receiver Installation Read this manual carefully before installing any transmitter or receiver. Complete the programming procedure before installing the receiver in its final location. The installer will need to have access to the receiver's programming button and must be able to view the receiver's LED light during the program-ming process.System The Extra-Small Transmitters and Receivers operate at 433.92 MHz and use code-hopping technology. The receiver will only operate with learned transmitters’ signal (see programming transmitter instruc-tions). Installation NOTE: Complete the programming instructions before installing the receiver in its final location. Install the receiver in a location so that the antenna is not surrounded by metal. Metal may cause a reduc-tion in range and inconsistency of signal reception. Door operator motors and power supplies may also cause radio frequency interference. If the receiver is installed in a metal enclosure, drill a hole in the enclosure and thread as much of the antenna as possible through the hole. This will reduce the effects the metal has on the receiver's reception. The receiver comes equipped with a wiring harness for easy installation.Receiver Wiring Harness:Orange Wire: Normally Open Relay Output Brown wire with White Stripe: Normally Open Relay Output Common Connection Red Wire: 24VACl24VDC Power Black Wire: Ground Purple Wire: 12 VACl12VDC Power Brown Wire: Normally Closed Relay Output Common Connection Yellow Wire: Normally Closed Relay Output Programming Instructions: NOTE: Prior to programming, ensure the receiver's LED light blinks red when power is applied. If the LED is not blinking red, disconnect and then reconnect the power. Programming transmitter(s) into the receiver's memory: The receiver can learn up to 12 transmitters. Follow the steps below to program your receiver(s). 1. Press the receiver's programming button for less than 2 seconds and release. The LED should change from blinking red to solid green. The receiver has entered programming mode. 2. Press and release the transmitter once and ensure that the receiver's LED changes to solid red. The receiver is learning the transmitter's code. 3. Wait a few seconds and then press the transmitter button again. The receiver's LED should now blink green several times. It has ended its learning procedure. The LED should now be blinking red.Exterior: Interior:Programming Button
Specifications:Transmitter Frequency: 433.92 MHzDimensions: 1.25 x .875 x .25”Security Code Method: Code HoppingBattery Life: 60,000 cyclesOperating Temperatures: -4°F to 122°FReceiver Frequency: 433.92 MHzDimensions: 2.25 x 1.25 x .75”Security Code Method: Code Hopping, up to 12 transmittersOperating Temperatures: -4°F to 122°FElectrical Rating: 100,000 cycles at 2 Amps. 24 VDC/120 VACInput Power: 24 VAC, 24 VDC or 12 VAC, 12VDCOutput: 2 relay outputs: 1 NO 1 NCProgramming the receivers output activation time: When the receiver is activated, its outputs will stay in the minimum activation state for approximately 1.5 seconds (default). This time can be adjusted to stay in the activation state for up to 4 hours. See below to adjust the receiver's output activation time. 1. Press the receiver's programming button for 4 seconds and release. The LED should be solid red. The receiver is in the activation time programming mode. 2. Press and release the transmitter button.3. When the desired time has elapsed (up to 4 hours) press the transmitter button again. The receiver's LED should blink green several times. When the procedure has ended, the LED should be blinking red. Deleting transmitters from the receiver's memory: See below to erase the receiver's memory of all previously learned transmitters. NOTE: Deleting previously learned transmitters does not change the receiver's output activation time. 1. Press the receiver's programming button for at least 8 seconds until the receiver's LED starts blinking green, then release the programming button. The LED should now be blinking red. 2. The receiver's memory is now cleared. FCC ID: SU7TRADCS433Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu