Cooper Wiring Devices RF9505 RF Full Control Duplex Receptacle User Manual RF9505

Download:
Mirror Download [FCC.gov]
Document ID	796731
Application ID	nXiZm9vsg3Cn36BhlJ2owg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.39kB (67344 bits)
Date Submitted	2007-05-24 00:00:00
Date Available	2007-05-24 00:00:00
Creation Date	2007-04-23 13:49:34
Producing Software	Adobe PDF library 7.77
Document Lastmod	2007-04-23 13:49:34
Document Title	RF9505
Document Creator	Adobe Illustrator CS2

Hot
Black
Noir
Phase
To install:
Negro
Vivo
Connect wires per wiring diagram as follows:
• Remove pre-stripped insulation on
device wires.
Both RF
• Strip wires in box 1/2”.
Controlled
• Twist ends of stripped wires together
White
Neutral
Blanc
Neutre
as per schematic.
Blanco
• Twist on wire connectors clockwise until secure. Neutro
• Connect green ground wire to bare wire, and
(Ground) Green
mount to box with screws.
(Terre) Verte
(Tierre) Verde
After completing successful installation LED on
device will blink until programmed.
For detailed programming instructions for your receptacle, refer to the ASPIRE RF manual that is
included with the Handheld (RFHDCSG) or Table Top (RFTDCSG) Controller.
Pour Installer:
Branchez les fils conformément au diagramme de câblage de la façon suivante:
• Enlevez l’isolant pré-dénudé des fils de l’appareil.
• Dénudez les fils de la boîte sur 1/2 po.
• Torsadez les extrémités des fils ensemble selon le schéma.
• Vissez les connecteurs par rotation bien à fond.
• Raccordez le fil de terre vert au fil nu et mountez sur la boîte à l’aide de vis.
Aprés une installation réussie, le voyant sur l’appareil clignote jusqu’à la programmation.
Les instructions de programmation détaillées de votre prise se trouvent à la notice de l’ASPIRE RF
qui est comprise avec l’inité de commande portable (RFHDCSG) ou celle de table (RFTDCSG).
Instalación:
Conecte los cables de acuerdo al diagrama de alambrado siguiendo estas indicaciones:
• Quite el aislamieno previamente pelado de los cables del dispositivo.
• Desforre 1/2 pulgada de los cables de la caja.
• Junte los extremos de los cables pelados y tuérzalos degún el disgrama esquemático.
• Atornille los connectores de cables torciéndolos en el sentido horario hasta que queden fijos.
• Conectar el cable verde tierra al cable desnudo y montar con los tornillos a la caja.
Después de terminar la instalación, el disositivo LED parpadeará hasta que sea programado.
Para obtener instrucciones detalladas para programmar su receptáculo, consulte el manual ASPIRE RF que se incluye
con el controlador portátil (RFHDCSG) o de mesa (RFTDCSG).
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This device complies with Part 15 of
the FCC Rules.
Operation is subject to the following
two conditions:
1: This device may not cause harmful
interference, and
2: This device must accept any
interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to
try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC CAUTION:
Any changes or modifications not
expressly approved by Cooper Wiring
Devices could void the user’s authority
to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1.1-111
Format                          : application/pdf
Title                           : RF9505
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2007:04:23 13:49:34+08:00
Modify Date                     : 2007:04:23 13:49:34+08:00
Metadata Date                   : 2007:04:23 13:49:34+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 168
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 12994 bytes, use -b option to extract)
Document ID                     : uuid:C9146177F33311DB89B5F04795A0CE0F
Instance ID                     : uuid:6a3aac04-f15e-11db-977a-000a958cde46
Producer                        : Adobe PDF library 7.77
Page Count                      : 1
Creator                         : Adobe Illustrator CS2

EXIF Metadata provided by EXIF.tools