Corsran Technology K200 Super Long Talking Time Bluetooth Mono Headset User Manual Manual
Shenzhen Corsran Technology Co., Ltd. Super Long Talking Time Bluetooth Mono Headset Manual
Manual
Using instruction
1
、Wearing
left right
2
、 Instructions：
Key Function：
1） ON/OFF-----Headset with intelligent voice prompts.
2） Volume keys
Long press the volume + key for the next song,
long
press the volume - key for the previous song.
3） Answer hang up keys
A. Answer or end end calls; double-
click redial recent
calls.
B. When listening to the music,click to pause,
and then click to play
C. Press 3S into a trailer two pairing mode.
2
、Charge:
1）This product uses a lithium-
ion polymer battery,for the
first
time charging needs about three hours to charge.
2）
When charing appears in red light , and blue light when
fully charged.
3）You can not use this product while charging .
3
、Pairing:
(F
irst use must be paired with the phone to use, after use
will automatically connect)
1) First, verify that your phone has Bluetooth
capabilities.
2) Open the phone Bluetooth function,
Meanwhile Bluetooth headset boot into pairing mode.
3) Use the phone's
Bluetooth feature to search for
Bluetooth devices,Select the device connected to the find.
4) Headset one for two (phone) pairing:
A cell phone when the headset is connected,
then disconnected A cell phone or shut down,
Then B cell phone is turned on and search for
devices connected to the phone,
then restart A cell phone for further connection ,
after that ,the phone will automatically connect.
5) If 10 minutes a Bluetooth headset paired device is not
found, the headset automatically shut down.
4
、Instructions for use:
1) Power on / off: Direct dial on (off) or dial down (on) switch
button.
2) answer a call: Click on the headset to answer hang up
button.
3) Hang up the phone: Press the end key on the headset to
answer.
4) make a call:
In standby operation, enter the number
Press the phone's dial button
Enter the number to make calls.
5) to end the call:
A, in a call to end the call, press the answer button again to
hang up to end the call.
B, in a call, press the button again to hang up t
he phone, end
the call.
6) refused to answer:
When the phone rings, press and hold the end key on the
headset to 1-2 seconds.
7) the volume increase / decrease: press the volume key,
click to increase or decrease the volume to maximum or
minimum volume,it all have intelligent prompt.
5, lack of electricity:
In working condition, Bluetooth headset with intelligent
voice prompt "battery low", please charge.
3
、specifications
1)Bluetooth version: 4.0
2)Support profile: Headset 、HFP、A2DP、AVRCP
3)Talking Time: About 24 hours
4)Standby Time: About 30 dadys
5)Charging Time: About 3 hours
6)Music Play Time: 22 hours
7)wireless Range: 10m
8)Previous song,next song: Yes
9)Battery Status Display on IOS device: Yes
10)Support Multi—point with 2 device: Yes
11)Voice reporting incoming phone number: Yes
12)Working Temperature: -10°C—60°C
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference
will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one o
r more
of the following measures:
--
Reorient or relocate the receiving antenna.
--
Increase the separation between the equipment and
receiver.
--
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--
Consult the dealer or an experienced radio/TV technician
for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:(1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.