Craftsman 113213170 User Manual 17 DRILL PRESS Manuals And Guides 1301300L

User Manual: Craftsman 113213170 113213170 CRAFTSMAN CRAFTSMAN 17 DRILL PRESS - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 17 DRILL PRESS #113213170. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 17 DRILL PRESS Manual

Open the PDF directly: View PDF PDF.
Page Count: 36

DownloadCraftsman 113213170 User Manual  17 DRILL PRESS - Manuals And Guides 1301300L
Open PDF In BrowserView PDF
f

Save This Manual "_
For Future Reference

owner's
manual

r

,

SP5188
MODELNO.
113.213170
DRILL PRESSWITH
MAXIMUM DEVELOPED
1 I/2 HP MOTOR

i

Serial
Number
Model and sedai number
may be found at the rear of
the head.
You should record both
model and serial number in
a safe place for future use.
i

i

CRRFTSMFIN

i

MOTORIZED

CAUTION:
READ ALL
INSTRUCTIONS
CAREFULLY

17-1NCH
FLOOR MODEL DRILL PRESS
• assembly
• operating
• repair parts

Sold by SEARS, ROEBUCK AND CO., Chicago,
P_rt No. SP5188

IL 60684 U.S.A.

FULL

ONE YEAR WARRANTY

ON CRAFTSMAN

DRILL

PRESS

If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect
in material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST
VICE CENTER/DEPARTMENT
THROUGHOUT THE UNITED STATES.
This warranty

applies

only while this product

This warranty gives you specific
vary from state to state.
SEARS,

GENERAL

ROEBUCK

SEARS SER-

is used in the United States.

legal rights, and you may also have other rights which

AND CO., Dept. 698/731A,

Sears Tower, Chicago,

SAFETY INSTRUCTIONS

1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
labels affixed to the tool. Learn its applicationand
limltabonsas well as the specificpotentialhazards
pecuhar to this tool.
2. GROUND ALL TOOLS
This toolisequipped with an approved3-conductor
cord and a 3-prong groundingtype plug to fit the
proper groundingtype receptacle.The green conductor in the cord is the groundingwire. Never
connectthe green wire to a live terminal.
3. KEEP GUARDS IN PLACE
in working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see that keys and
adjustingwrenches are removed from tool before
turningit on.
5. KEEP WORK AREA CLEAN
Clutteredareas and benchesinviteaccidents.Floor
must not be slippery due to wax or sawdust.
6, AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locationsor
expose them to rain. Keep work area well lighted.
Provide adequate surroundingwork space.
7. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area.
8. MAKE WORKSHOP CHILD-PROOF
With padlocks, master switches,by removingstarter keys, or storing tools where children.can'tget
them.
9. DON'T FORCE TOOL
It will do the job better and safer at the rate for
which it was designed.
10. USE RIGHT TOOL
Don't force tools or attachment to do a job it was
not designed for.
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties, or
jewelry (rings,wrist watches) to get caughtinrnoving parts. NONSLIP footwear is recommended.
Wear protective hair coveringto contain long hair.
Roll long sleeves above the elbow.
12. USE SAFETY GOGGLES (HEAD PROTECTION)
Wear safety goggles (must comply with ANSI

13.

14.
15.

16.

17.

18.

19.

20.

IL 60684

FOR POWER TOOLS

Z87.1) at all times. Everyday eyeglasses are not
safety glasses. They only have impact resistant
lenses. Also, use face or dust mask if cutting operat=on is dusty, and ear protectors (plugs or muffs)
during extended periods of operation.
SECURE WORK
Use clamps or a vise to hold work when practical.
It frees both hands to operate tool.
DON'T OVERREACH
Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories.
DISCONNECT TOOLS
Before servicing; when changing accessories such
as blades, bits, cutters, etc.
AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plugging in.
USE RECOMMENDED
ACCESSORIES
Consult the owner's manual for recommended accessories. Follow the instructions that accompany
the accessories. The use of improper accessories
may cause hazards.
NEVER STAND ON TOOL OR ITS STAND
Serious iniury could occur if the tool is tipped or if
the cutting tool is accidentally contacted. Do not
store materials above or near the tool such that it
is necessary to stand on the tool or its stand to
reach them.
CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
ensure that it will operate properly and perform its
intended function. Check for alignment of moving
parts, binding or moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direct,on of rotation of the blade or cutter only.
22. NEVER LEAVETOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a
complete stop.

additional safety instructions for drill presses

ta

£
¢
t,.

WARNING:
FOR YOUR OWN SAFETY,
DO NOT
USE YOUR DRILL PRESS UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS...
AND UNTIL YOU
HAVE READ AND UNDERSTAND
THE FOLLOWING:
1. General Safety Instructions

for Power Tools.

2. Getting to Know Your Drill Press
3. Basic Drill Press Operation
4. Adjustments
5. Maintenance

..........................
..........................

........

.............

-

2
17

--

22
24
25

6. Stability of Drill Press
If there ts any tendency of the drill press to tilt or
move during any use, bolt It to the floor or a flat
piece of V2" exterior plywood large enough to
stabilize the drill press. Bolt the plywood to the
unders=de of the Base. so it extends at least to
both s_des. Make sure the plywood won't trip the
operator. Do not use pressed wood panels-they can break unexpectedly.
If the workpiece is too large to easily support with
one hand, prov=de an auxiliary support.
7. Location
Use the drill press in a well lit area and on a level
surface clean and smooth enough to reduce the
nsk of trips, slips, or falls. Use it where neither the
operator nor a casual observer is forced to stand
in line with a potential kickback.
8. Kickback
A kickback occurs when the workpiece is suddenly
thrown in the OPPOSITE direction to the DIRECTION OF FEED: THIS CAN CAUSE SERIOUS INJURY. Kickbacks are most commonly caused by
use of accessories NOT recommended for this tool.
9. Protection: Eyes, Hands, Face, Earsand Body
WARNING: TO AVOID BEING PULLED INTO
THE SPINNING TOOL -1. Do NOT wear:
-- gloves
-- necktie
-- loose clothing
-- jewelry
2. Do tie back long hair
a. If any part of your drill press is missing, malfunctioning, has been damaged or broken..,
such
as the motor swdch, or other operating control,
a safety device or the power cord..,
cease
operating immediately until the particular part
is properly repaired or replaced.
b. Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece should unexpectedly shift or
your hand should slip.
c. To avoid injury from parts thrown by the spring.
follow instructions exactly as given and shown
in adjusting spring tension of quill.

---

--

---

--

--

--

To prevent the workpJece from being
torn from your hands, spinning of the
tool, shattering the tool or being thrown,
always properly support your work so
_twon't shift or bind on the tool
Always posJt_on BACKUP MATERIAL (use
beneath the workptece) to contact the left
side of the column.
Whenever possfble, position the WORKPIECE to contact the left side of the column--_f tt _s too short or the table is tilted,
clamp solidly to the table. Use table slots
or clamping ledge around the outside edge
of the table.
When using a drill press VICE. always fasten it to the table.
Never do any work "FREEHAND"
(handholding workptece rather than supporting it
on the table), except when polishing.
Securely lock Head and Support to Column,
Table Arm to support, and Table to Table
Arm before operating drill press.
Never move the Head or Table white the
tool is running.
Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration.
If a workpiece overhangs the table such
thai it will fall or tip if not held, clamp it to
the table or provide auxiliary support.
Use fixtures for unusual operations
to
adequately hold, guide and position workpiece.
Use the SPINDLE SPEED recommended
for the specific operation and workpiece
material--check
the label inside the Belt
Guard for drilling information; for accessories, refer to the instructions provided
with the accessories.
f. Never ckmb on the drill press Table, it
could break or pull the entire drill press
down on you.
g, Turn the motor Switch Off and put away
the Switch Key when leaving the drill
press.
h. To avoid injury from thrown work or tool
contact, do NOT perform layout, assembly, or setup work on the table while
the cutting tool is rotating.

10. Use only accessories designed for this
drill press to avoid serious injury from
thrown broken parts or work pieces.
a. Holesaws must NEVER be operated on
this dr_ll press at a speed greater than
400 RPM.

_.
_:
"_
t,/)

b

Drum sanders must NEVER be operated on
th=s drill press at a speed greater than 1800
RPM.

c. Do not=nstatlor use any drillthat exceeds 7""_n
lengthor extends6" belowthechuckjaws They
can suddenlybend outward or break
d. Do not use w=rewheels, routerb=ts,shapercutters, circle (fly)cutters or rotaryplaners on th=s
drill press.
11. Note and Follow the Safety Warnings and Instructions that Appear on the Panel on the
Right Side of the Head:

t3.

Think Safety. Safety _sa combination of operator
common sense and alertness at all times when me
dNII press ,s be0ng used

WARNING:
Do not allow familiarity (gained
from
frequent use of your drill press) to become commonplace. Always remember that a careless fraction of a second is sufficient to inflict severe injury.
The operatJons of any power tool can result in toreign
ObleCts being thrown into the eyes, whnch can result in
severe eye damage Always wear safety goggles comply with ANSI Z87.1 (shown on Package) before commencing power tool operation. Safety Goggles are
available at Sears retanl or catalog stores.

• IDANGER I FOR YOUR OWN SAFETY:
Ull

P.ec{M_'_lo_d

_JU

m _i_nec_or

Odll

$114ed---

_111 !

Eel

Ch_l

In.do

I_ II_f

a_m te supOmt.

_

_

Covet.

I_1

tt_le

_ _m

IN_k_r

_eeL

12. This Drill Press has 16 speeds as listed below:
200 RPM
800 RPM
290 RPM
870 RPM
350 RPM
1440 RPM
430 RPM
1630 RPM
500 RPM
1820 RPM
580 RPM
2380 RPM
640 RPM
2540 RPM
720 RPM
3630 RPM
See inside of belt guard for specific placement o!
belt on pulleys.

WEAR YOUR

SA

glossary of terms
t. Workpiece
The =ternon wh=chthe cutting operations_s being
performed.
2. Drill
The cuttingtoolused in the drill press to make holes
=na workplece.
3. Backup Material
A piece of woodplaced between the workp_eceand
table ....
st preventswood in the workpiece from
splintering when the drill passes through the backside of the workplece.... also preventsdrillinginto
the table top.

,

S°

Revolution Per Minute (R.P.M.)
The number of turns completed by a spinning
in one minute

oblect

Spindle Speed
The RPM of the spindle.

(.._o

o_
t, 8

table of contents
Page
General Safety Instructions for Power Tools ......
Additional Safety Instructions for Drill Presses ....
Glossary of Terms ..........................
Table of Contents ...........................
Motor Specifications and Electrical
Requirements ..............................
Unpacking and Checking Contents .............
Table of Loose Parts ........................
Location and Function of Controls ..............
Assembly ................................
Assembly of Column and Table Hardware...
Installing the Table .....................
Installing the Head .....................
Mounting Motor ........................
Installing Motor Pulley ...................
Tensioning Belt ........................
Installing Belt Guard Knob ...............
Motor Connections .....................
Installing Feed Handles .................
Installing the Chuck .....................
Installing Light Bulb .....................

2
3
5
5
6
7
8
9
10
10
11
11
12
12
12
13
14
14
14
16

Adjustingthe Table Square to Head .......
Revel Scale ...........................
Getting to Know Your Drill Press ..............
On-Off Switch .........................
Drillingto a Specific Depth ...............
LockingChuck Desired Depth ............
RemovingChuck and Arbor ..............
Re-Installingthe Chuck and Arbor .........
Basic Drill Press Operation ..................
InstallingDnlls .........................
PositioningTable and Workpiece ..........
Tilting Table ...........................
Hole Location .........................
Feeding ..............................
Adjustments ..............................
Quill Return Spring .....................
Maintenance ..............................
Lubrication ...............................
Recommended Accessories..................
Trouble Shooting ..........................
Repair Parts ..............................

;J

Page
16
18
17
19
20
20
21
22
23
23
24
25
25
25
25
25
26
26
26
27
28

motor specifications and electrical requirements
MOTOR

SPECIFICATIONS

Th_s drill press _s designed to use a 1725 RPM motor
only Do not use any motor that runs faster than 1725
RPM It _swired for operation on 110-120 voltS. 60 HZ,
alternating current
WARNING:
TO AVOID
INJURY FROM
UNEXPECTED STARTUP, DO NOT USE BLOWER OR
WASHING
MACHINE MOTORS OR ANY MOTOR
WITH AN AUTOMATIC
RESET OVERLOAD PROTECTOR.

CONNECTING
TO POWER
SOURCE OUTLET
This machine must be grounded while _n use to protect
the operator from electric shock.
Plug power cord into a 110-120V properly grounded
type outlet protected by a 15-amp. dual element time
delay or Circu=t breaker.
NOT ALL OUTLETS ARE PROPERLY GROUNDED.
IF YOU ARE NOT SURE THAT YOUR OUTLET, AS
PICTURED
BELOW, IS PROPERLY GROUNDED,
HAVE IT CHECKED BY A OUAMFIED ELECTRICIAN.

Thts power tool _s equipped w_lh a 3-conductor
cord
and grounding type plug. approved by Underwriters'
Lalooratones and the Canadian Standards Assoclat=on
The ground conductor has a green lOCket and _S attached to the tOol housing at one end and to the ground
prong =n the attachment plug at the other end.
This plug requires
outlet as shown.

a mating 3-conductor

grounded

type

If the outlet you are planmng to use for th=s power tool
=sof the two prong type. DO NOT REMOVE OR ALTER
THE GROUNDING
PRONG IN ANY MANNER. Use
an adapter as shown and always connect the grounding
lug to known ground.
It is recommended that you have a qualified electrlaan
replace the TWO prong outlet w=th a properly grounded
THREE prong outlet.
An adapter as shown below =savadable for
plugs to 2-prong receptacles.
WARNING:
THE GREEN GROUNDING
TENDING FROM THE ADAPTER MUST
NECTED TO A PERMANENT GROUND
TO A PROPERLY GROUNDED OUTLET

WARNING: TO AVOID ELECTRIC SHOCK, DO NOT
TOUCH THE METAL PRONGS ON THE PLUG,
WHEN INSTALLING OR REMOVING THE PLUG TO
OR FROM THE OUTLET.

GROUNDING

connect=rig
LUG EXBE CONSUCH AS
BOX.

LUG

WARNING: FAILURE TO PROPERLY GROUND THIS
POWER TOOL CAN CAUSE ELECTRICUTION
OR
SERIOUS SHOCK, PARTICULARLY WHEN USED IN
DAMP LOCATIONS, OR NEAR METAL PLUMBING.
IF SHOCKED, YOUR REACTION COULD CAUSE
YOUR HANDS TO HIT THE CUTTING TOOL.
IF POWER CORD IS WORN OR CUT, OR DAMAGED
IN ANY WAY, HAVE IT REPLACED IMMEDIATELY
TO AVOID SHOCK OR FIRE HAZARD.

\

3-PRONG'
PLUG

ADAPTER

NOTE: The adapier illustrated is for use only _f you
already have a properly grounded 2-prong receptacle.
Adapter =snot allowed m Canada by theCanadian Electrical Code.

\
GROUNDING
PRONG

ALWAYS USE A
PROPERLY
GROUNDED
O UTLET

Your unit =sfor use on less than 120 volts. It has a plug
that looks like the one above.

The use of any extension
power
heating

determine
cord. Use
prong
which

cord

will cause

some

loss of

To keep this to a minimum
and to prevent
overand motor burll-out,
use the table below
to
the minimum
wire size (A W.G.) extension
only 3 wire extension
cords which have 3-

groundlr_g
type plugs
accept the tools plug.

Extens=on Cord Length
0-25 Feet
26-50 Feet
51-100 Feet

and

3-pole

receptacles

Wire S=zeA.W.G.
16
14
12

unpacking and checking contents
WARNING:
TO AVOID
INJURY
FROM UNEXPECTED STARTING OR ELECTRICAL SHOCK, DO
NOT PLUG THE POWER CORD INTO A SOURCE
OF POWER. THIS CORD MUST REMAIN UNPLUGGED WHENEVER
YOU ARE WORKING ON THE
DRILL PRESS.
Model 113 213170
one box.

Drill Press ,s shipped complete m

1 Unpacking and Check=ng Contents
a. Separate all "loose pads" from packag=ng materials and check each Item with "Table of Loose
Parts" to make sure all items are accounted for,
before d=scarding any packing material. Some
loose parts are contained inside the belt guard.
Open the belt guard cover to find them.
WARNING: IF ANY PARTS ARE MISSING, DO NOT
ATTEMPT TO ASSEMBLE DRILL PRESS, PLUG IN
THE POWER CORD, OR TURN THE SWITCH ON
UNTIL THE MISSING PARTS ARE OBTAINED AND
ARE INSTALLED CORRECTLY.

TABLE
Item
A
B
C
O
E
F
G
H

OF LOOSE

PARTS

Description
Table .........
Column Support Asm ........
Owner's Manual
..............
Motor ..............
Bag of Loose Parts
..........
Base .......................
Head Asm ...............
Box of Loose Parts ..............

2. Remove the protective oil thaE is applied to the
table and column. Use any ordinary household type
grease and spot remover.
WARNING: TO AVOID FIRE OR TOXIC REACTION, NEVER USE GASOLINE,
NAPTHA OR
SIMILAR HIGHLY VOLATILE SOLVENTS.
3. Apply a coat of paste wax to the table and column
to prevent rust. Wipe all parts thoroughly with a clean
dry cloth.

H

F

E

D

C

Qty.
1
1
I
I
I
1
1
1

LLStof Loose Parts =n Box 507864
Item

Description

A Feed Handle ........
B Key Drift ...................
C Wrench Hex "L" M3 ................
D Wrench Hex "L" M4 ...............
E Wrench Hex"L" M5 .................
F Crank ........................
G Clamp-Column .......................

Qty.
3
t
t
1
1
1
1

List of Loose Parts in Bag 507865
Item
Description
H Chuck ..............................
I Chuck Key ..........................
inlll

i

i

Qty.
1
1

i i

LsoL.sPas
a-Item
J
K
L
M

Description
Screw-Hex HD. M10 x 1.5-40 ...........
Key-Switch ..........................
Knob ..............................
Screw-Pan HD. M5 x 0.8-12 ............

Qty.
4
1
1
1

K

L

M..._
i

i

List of Loose Parts in Bag 507867
Item

Description

N Idler Pulley Assembly .................
O Pulley-Motor .........................
P Belt "V" 112 x 27 .....................
Q Belt "V" 112 x 29 .....................
R Screw-Hex HD, M8 x 1.25-20 ...........
S Washer 21/64 x 7/8 x 3164 .............
T Nut-Hex M8 x 1.25 ...................

Qty.
1
1
1
1
4
8
4

Q

>R

8

TD

location and function of controls
1. BELT TENSION HANDLE...
Turn handle counter
c!ockwfse to apply tens,on to belt. turn handle
clockw,se to release belt tension.
2.

BELT TENSION LOCK HANDLES...
Tightening
handles locks motor bracket support and BELT
TENSION HANDLE to maintain correct belt d_stance and tens=on.

3. HEAD LOCKS...
Lock the head to the column.
ALWAYS have them locked m place wh=leoperating the drill press
4. SUPPORT LOCK...
Tightening locks table support to column. Always have it locked =nplace while
operating the DrHt Press.
5. TABLE CRANK . . . Turn clockwise to elevate
table. Support lock must be released before operating crank.
6. TABLE BEVEL LOCK...
Locks the table in any
position from 0°.--45_.
7. TABLE LOCK ...
Allows table to be rotated an
various positions and locked.

9. CHUCK...
accesso_/to

Holds drdl b=tor other recommended
perform desired operations.

10. BEVEL SCALE...
Shows degree table is tilted
for bevel operat=ons Scale _s mounted on side of
arm.

11. SPRING CAP...
sprmg tens=on.

Provides means to adjust quill

12. DEPTH SCALE...
Allows operator
press to drill to a desired depth.

to adjust drill

13. DRILL "ON-OFF" SWITCH...
Turns drill press
on and off ....
also used to lock drill press in off
pos=t=on.
14. LIGHT "ON-OFF" SWITCH...
Turns the light on
and off.
15. CHUCK KEY...
Used to tighten drill in the chuck
and also to loosen the chuck for drill removal.
16. DEPTH SCALE LOCK...
Locks the depth scale
at selected position.

8. FEED HANDLE...
For moving the chuck up or
down. One or two of the handles may be removed
=f necessary whenever the workpiece =s of such
unusual shape that it interferes with the handles.

16
14

13

€

..=

10

TABLE REMOVED
FOR CLARITY

assembly
WARNING: FOR YOUR OWN SAFETY, NEVER CON*
NECT PLUG TO POWER SOURCE OUTLET UNTIL
ALL ASSEMBLY STEPS ARE COMPLETED.
FRAMING
Check

TOOLS

NEEDED
I.._.l'"I" I"" '

15/16 _ BOX END
WRENCH

MEDIUM
SCREWDRIVER

i

i

ASSEMBLY
HARDWARE

i

*
' ....

DRAW

SQUARE MUST BE TRUE.

its accuracy

ADJUSTABLE
WRENCH

_,,

SHOULD

BE NO GAP OR OVERLAP

SQUARE

IS FLIPPED

OVER

EDGE

OF

BOARD 3/4" THICK-THIS EDGE MUST BE
PERFECTLY
STRAIGHT

j ..... , .......
,._.,..(_
COMBINATION
I"

8-INCH

below.

STRAIGHT

LINE ON BOARD
ALONG THIS EDGE

" ' " "___

as illustrated

LIGHT

WHEN

IN DOTTED

POSITION

i

OF COLUMN

AND TABLE

1. Position base on floor. Remove protective covering
and discard.

COLUMN
SUPPORT

10ram OIA. x 40mm
LONG BOLT

2, Remove protective sleeve from column tube and
discard. Place column assembty on base, and align
holes in column support with holes in base.
3. Locate (4) four 10ram Dia. x 40ram long bolts (see
illustration) in loose parts bag.

BASE

4. Install a bolt in each hole through column support
and base and tighten with adiustable wrench.

i

TABLE
SUPPORT
.

Locate table crank and supportlock in loose parts
box.

6. Install support lock from left side into table support
and tighten by hand,
7. Install table crank assembly and tighten set screw
with a 3mm HEX "V' wrench.
HANDLE
SUPPORT
LOCK

TABLE
SUPPORT

.

TABLE
CRANK

COLUMN
COLLAR

Position column collar over rack and tighten set
screw in collar, using 3mm HEX "L" wrench,
supplied in loose parts bag. Collar should not be
angled on the column. Only tighten set screw
enough to keep collar in place; rack should still
slide freely in collar.

COLUMN

CAUTION: To avoid column or collar damage,
do not overtighten set screw,

10

INSTALLING

THE TABLE
TABLE

!

Loosen support lock and ra=se table support 10y
tumRngtable crank clockwise unbl support =s at a
working height level. Tighten support lock.
TABLE
SUPPORT

f

RACK

TABLE
SUPPORT

,

Remove protective covering from table and discard. Place table in table support and tighten table
lock (located under table) by hand.

!

TABLE

LOCK
ii

INSTALLING

THE

TABLE

HEAD

CAUTION: The head assembly
pounds. Carefully lift head.

weighs

about

55

1. Remove protective bag from head assembly and
discard. Carefully lift head above column tube and
slide it onto column making sure head slides down
over column as far as possible. Align head with
table and base.
COLUMN

HEAD

HEAD

LOCK
SCREWS

2. Using a 5mm Hex "L"wrenchtighten the two head
lock set screws on the right side of the head.

=_'r
__=
LD

11

1. Locate four (4) 8mm,
t,
DJa x 20ram long hex head
bolts, eight (8)flat _vashers, and four (4) hex nuts

_f,f

.

among,oose
a.s.
2. Install hex head
head.

/"

_,

: .

...->./

bolts through motor bracket

on

3. Place motor in position so motor base slotsline up
with motor bracket slots. Install flat washers and
hex nuts as illustrated. (Do not tighten)
4. Motorshaftshouldbeascloseaspossibletocenter
of round opening in belt guard.
_

./ ._/
-_ .!._.y
--_"
__r
_I
:_J'/

HEXNUT

"_

_']
t,.__

HI_X
NUT

___fJ
/
I",l,,"_-J}_-',_'_nnll_1
I
I_[_i_ Uuv" "--,_
_1_
'_

FLATWASHER

s'

._/____
..___-_o_.._'_...'_|

_"

Ilmm DIA. ,, 2DramLONGBOLT

_S_//UOTO
R--z_.,,_'//

I I

-

J I
_

FLAT

.

,

MOTOR

I

PULLEY

INSTALLING

MOTOR

PULLEY

1. Find the motor pulley in loose parts bag.
2. Slide pulley onto motor shaft. Line up the flat surface on the motor shaft with the set screw in pulley.
3. Make sure the pulley does not rest on the lower
guard.
FLAT

4. Tighten the set screw using a "4" mm Hex"L"wrench.

INSTALLING

AND

TENSIONING

SURFACE

STRAIGHT

BELT

EDGE

WARNING: TO AVOID INJURY DUE TO ACCIDENTAL STARTING ALWAYS TURN DRILL PRESS OFF
AND REMOVE SWITCH
KEY BEFORE MAKING
BELT ADJUSTMENTS.
1. Place a straight edge such as a piece of wood,
metal, or framing square across the top of pulleys.
2. Move the motor upward until the pulleys are in line.
Tighten the motor mount nuts using an adjustable
wrench.
NOTE: To avoid rattles or other noise, motor frame
must not touch lower belt guard.
3. Release Belt Tension Lock handles located on
each side of Drill Press head by turning them
counterclockwise.
LOWER
BELT
GUARD

BELT
TENSION
LOCK
HANDLE

MOTOR
MOUNT
NUTS

MOTOR

BELT
TENSIOr_
HANDEE

4. Loosen Belt Tension handle by turning clockwise.

5

Locate center pulley assembly
and place inproper hole

tn !oose parts bag

SPINDLE

PULLEY

6. Locate two (2) V-belts in the loose parts bag.
7. Use speed chart inside belt guard to Choose speed
for drilling operation. Install belts in correct position
for desired speed. The longer of the two belts is
always positioned between the spindle pulley and
idler pulley,
NOTE: Refer to chart inside belt guard for Recommended Drilling Speeds.
IDLER PULLEY

8. Apply tension to belt by turning Belt Tension Handle
counter clockwise until belt deflects approximately
1/2 inch by thumb pressure at its center.
9. Tighten Belt Tension Lock Handles.

BELT
TENSION
LOCK
HANDLE

CAUTION: Over tensioning belt may cause motor not
to start or damage bearings.
10..If belt slips while drilling, readjust belt tension,

TENSION
HANDLE

BELT GUARD,

BELT GUARD

Smm DIA.

x 12ram

LONG

SCREW
BELT GUARD

INSTALLING

PAN HD.

KNOB

BELT

GUARD

KNOB

1. To attach belt guard knob, locate knob and 5mm
Dia. x 12mm long pan hd. screw in loose pads
bag, Install screw in hole located in guard and attach knob turning until tight.
WARNING: TO AVOID POSSIBLE INJURY KEEP
GUARD IN PLACE AND IN PROPER WORKING
ORDER WHILE OPERATING.

13

MOTOR

CONNECTIONS

WARNING: FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL
ALL ASSEMBLY STEPS ARE COMPLETED,

BLACK
WIRE TO
TERMINAL
#1
COPPER
POST

t. Open motor connector box cover located on underside of motor using a flat blade screwdriver.
WARNING: TO AVOID ELECTROCUTION,
NEVER
CONNECT ANYTHING
BUT THE GROUND WIRE
{COLORED GREEN) TO THE GREEN SCREW.
2. Remove GREEN SCREWand insertthrough round
metal terminal on the end of the GREEN wire of
power cord.
3. Reinsert GREEN SCREW in threaded hole that it
was removed from and tighten securely.
4. Insert terminal end of WHITE wire on spade terminal (next to silver post) marked #4 on the motor,
Push terminal firmly until seated.

GREEN WIRE
TO GREEN SCREW
STRAIN RELIEF
GROOVE
WHITE WIRE
TO TERMINAL
SILVER POST

#4

laO_0R

5. Insert terminal end of BLACK wire on spade terminal (next to copper post) marked #1 on the motor.
Push terminal firmly until seated,
6, Close motor connector box being sure that power
cord is seated in strain relief groove and tighten
box cover screws.

GREEN
IGROUNO)

7. Do not plug in power cable.

INSTALLING

FEED HANDLES.

1. Locate three (3) feed handles among loose.parts.
2. Screw the feed handles into the threaded holes in
the hub and tighten.

HUB

FEED
HANOLE

INSTALLING

\

THE CHUCK

NOLE

1. Clean out the TAPERED HOLE in the chuck. Clean
both tapered surfaces on the arbor with a clean
cloth. Make sure there are no foreign particles sticking to the surfaces. The slightest piece of dirt on
any of these surfaces will prevent the chuck from
seating properly. This will cause the drill to
"wobble."
_j

ARBOR
CLEAN THIS
SURFACE

14

m

2. Slide the chuck up over the arbor as illustrated.

"="----

SPINOLE

ARBOR

\

\
i

i

SUPPORT
LOCK

4. Unlock support lock and raise table so its about
two (2) inches below tip of chuck.
5. Turn chuck sleeve clockwise and open jaws in
chuck completely.
6. Turn feed handles cotanterclockwiseand force
chuck against table until chuck is secure;

CHUCK
SLEEVE

INSTALLING

LIGHT

BULB

1. Install a light bulb (not larger than 60 watt) into the
socket inside the head.

ADJUSTING
TO HEAD

THE TABLE

SQUARE

NOTE: The combination square must be "true." See
"Unpacking
and Checking
Contents"
section for
method.
1. Insert a precision ground steel rod approximately
3" long into chuck and tighten.
2. With table raised to working height and locked on
column, place combination square flat on table beside rod.

TABLE

3. If an adjustment is necessary, loosen the set screw
under bevel lock with 3ram Hex "L" wrench, then
loosen the table bevel lock with a 15116" wrench.
(These adjustments are located under the table).
4. Align the table square to the rod by rotating
table until the square and rod are in line.
5. Retighten
6. Retighten

the

table bevel lock.
set screw.
BEVEL
LOCK

SCREW

|

BEVEL

SCALE

TABLE

NOTE: The bevel scale has been included to provide
a quick method for beveling the table to approximate
angles. If precise accuracy is necessary, a square, or
other precision measuring tool should be used to position the table.

1, To use the bevel scale do the following:
a. Loosen set screwand table bevel lock (see step
3 above).
b. Move table so desired angle or bevel scale is
straightacrossfrom zerolineon table support.
c. Retighten table bevel lock and set screw.

POINTER
SCALE

16

getting to know your drill press
FEED SPRING
ADJUSTMENT

FEED
SPRING

17
SPRING
CAP

1
BELT GUARD

4"

SWITCH

2
BELT TENSION
LOCK HANDLE

18
CHUCK
19
ARM

2
BELT TENS_N
LOCK HANDLE

20
BEVEL LOCK
(UNDER TABLE)

3
BELT TENSION
HANDLE

23
SUPPORT LOCK

4
HEAD LOCK

DEPTH
SCALE LOCK
22
BEVEL SCALE

16
lS

21
TABLE LOCK

5
FEED HANDLE

DEPTH
INDICATOR

6
COLUMN COLLAR

14
DEPTH SCALE
QUILL AND SPINDLE ASSEMBLY
INSIDE OF DRILL PRESS

SPLINES

J_'_

7
TABLE SUPPORT
SPINDLE

(GROOVES)

e
TABLE CRANK
13
TABLE
12
COLUMN

(TEETH)
RACK

24
CHUCK

.......___GE

KEY

_ ._........_
KEY

9
RACK

11
COLUMN

10
BASE

ARBOR

H

17

.m

==,._,

See _nside of belt guard for specific placement
on pulleys

This Drill Press has 16 speeds as hsted Cerow
200RPM
290RPM
350RPM
430RPM
500RPM
580RPM

640RPM
720RPM
800RPM
870RPM
1440RPM
1630RPM

,

,

1820RPM
2380RPM
2540RPM
3630RPM

SPINDLE
,

,

,,

,,,,

i

SPEEDS

IN

R.P.M.

200

290

350

430

500

580

640

720'

8O0

870

1820

2380

1440

1630
3630

1. BELT GUARD ASSEMBLY . . . Covers pulleys
and belt during operation of drill press.

14. DEPTH SCALE...
drilled.

2. BELT TENSION LOCK HANDLES...
Tightening
handles locks motor bracket support and BELT
TENSION HANDLE to maintain correct belt dislance and tension.

15. DEPTH SCALE INDICATOR...
depth selected on depth scale.

17. SPRING CAP...
spring tension.

4. HEAD LOCKS...
Lock the head to the column.
ALWAYS have them locked in place while operating the drill press.

18. CHUCK...
accessory

Provides

means to adjust quill

Holds drill bit or other recommended
to perform desired operations.

Locks the table in any

21. TABLE LOCK...
Table can be rotated in various
positions and locked.
22. BEVEL SCALE...
Shows degree table is tilted
for bevel operations. Scale is mounted on side of
arm.
23. SUPPORT LOCK...
Tightening locks table support to column. Always have it locked in place while
operating the Drill Press.
24. CHUCK KEY...
It is a self-ejecting chuck key
which will "pop" out of the chuck when you let go
of it. This action is designed to help prevent throwing of the chuck key from the chuck when power
is turned "ON". Do not use any other key as a
substitute, order a new one if damaged of lost.

10. BASE...
Supports Drill Press. For additional stability, holes are provided in base to bolt Drill Press
to floor. (.See "Additional Safety Instructions for Drill
Presses,")

25. BELT TENSION...
Refer to section"Assembly-Installing and Tensioning Belt"

11, COLUMN SUPPORT...
Supports column, guides
rack. and provides mounting holes for column to
base.

Provides working surface

Locks the depth scale

20. TABLE BEVEL LOCK...
position from 0"-45 _.

9. RACK...
Combines with gear mechanism to provide easy elevation of table by hand operated table
crank.

13. TABLE...
workpiece

Indicates drilling

19. ARM...
Extends beyond table support for mounting and aligning the table.

5. "FEED HANDLE...
For moving the chuck up or
down, One or two of the handles may be removed
if necessary whenever the workpiece is of such
unusual shape that it interferes with. the handles.
6. COLUMN COLLAR...
Holds the rack to the column. Rack remains movable in collar to permit
table support movements,
7. TABLE SUPPORT...
Rides on column to support
arm and table.
8. TABLE CRANK . . . Turn clockwise to elevate
table. Support lock must be released before operating crank.

Connects head. table, and base on
tube for easy alignment and move-

Shows depth of hole being

16. DEPTH SCALE LOCK...
to selected depth.

3. BELT TENSION HANDLE...
Turn handle counter
clockwise to apply tension to belt, turn handle
clockwise to release belt tension.

12. COLUMN...
a one-piece
ment.

of ioelts

26. DRILLING SPEED...
Can be changed by placing
the belt in any of the STEPS (grooves) in the pulleys. See Spindle Speed inside belt guard.
To determine the approximate drilling speed, refer
to the table inside the belt guard.

to support

18

.....

27

DRILL "ON-OFF" SWITCH ...
Has locking feature. THIS FEATURE IS INTENDED TO HELP
PREVENT
UNAUTHORIZED
AND POSSIBLE
HAZARDOUS
USE
BY
CHILDREN
AND
OTHERS,

Insert KEY into swftch.
NOTE: Key is made of yellow plastic.

z 3=
Dee

To turn drill ON ...
Insert finger under switch lever and pull.

To turn drill OFF...

Push lever in,

In an emergency;..,
the drill bit BINDS...
STALLS
• . . STOPS ... or tends to tear the workpiece loose
• .. you can QUICKLY turn the drill OFF by hitting the
switch with the palm of your hand.

To lock switch in OFF position..,
hold switch IN with
one hand,..
REMOVE key with other hand.
WARNING:
FOR YOUR OWN SAFETY, ALWAYS
LOCK THE SWITCH "OFF" WHEN DRILL PRESS IS
NOT IN USE...
REMOVE KEY AND KEEP IT IN A
SAFE PLACE...
ALSO . . . IN THE EVENT OF A
POWER FAILURE (ALL OF YOUR LIGHTS GO OUT)
OR
BLOWN
FUSE
OR
TRIPPED
CIRCUIT
BREAKER, TURN SWITCH OFF . . . LOCK IT AND
REMOVE THE KEY. THIS WILL PREVENT
THE
DRILL PRESS FROM STARTING UP AGAIN WHEN
THE POWER COMES BACK ON.

19

DRILLING

TO A SPECIFIC

DEPTH

To drill a BLIND hole (no! all the way lhrough)
given depth, proceed as follows.

!:

to a

1. Mark the deplh of lhe hole on the side of lhe workpiece.
2. Loosen the depth scale lock.
3. With the switch OFF, bring the drill down until the
TiP or lips of the drill are even with the Mark.

DEPTH
SCALE LOCK

4. Turn the depth scale counterclockwise until it stops
moving.
5. Tighten the depth scale lock.
DEPTH
SCALE

6. The drill will now be stopped at this depth until the
depth scale is readjusted.

MARK

ANOTHER

WAY

-- DEPTH

DEPTH

SCALE

SCALE

1. With the switch OFF, loosen the depth scale lock.
-2. Turn the depth scale clockwise until the depth scale
indicator points to the desired drilling depth on the
depth scale.

DEPTH

3. Tighten the depth scale lock:

POINTER

4. The chuck or drill will now be stopped after traveling
downward the distance selected on the depth
scale.

LOCKING

CHUCK

DESIRED

DEPTH

1. With the switch off--loosen the depth scale lock.
2. Turn the feed handles until the chuck is at the
desired depth. Hold feed handles at this position.
TIP TOUCHES
WORKPIECE

0

.....................

OEPTH SCALE
LOCK

3

Turn the depth scale clockwise

until it stops.

4, Tighten the depth scale lock,
5. The chuck will now be held at this depth when the
feed handles are released,

SCALE

ml

1

SPINDLE KEY
HOLE

REMOVING

CHUCK

QUILL KEY
HOLE

AND ARBOR

ii

ARBOR
LOCKING
COLLAR

"._ "o
CHUCK
SLEEVE

1. With switch off -- adjust depth scale to hold drill
at a depth of (3) three inches. (See instructions for
"Locking chuck at desired depth").
2. Align key holes in spindle and quill by rotating the
chuck by hand. (See illustration)
3. Insert key wedge into key holes.
4. Tap key wedge lightly until the chuck and arbor
fall out of spindle.
NOTE: Place one hand below chuck to catch it when
it falls out.

\

WEDGE

KEY

CHUCK
SLEEVE

BODY

21

O

n-

r-

RE-INSTALLING

THE CHUCK AND ARBOR

t. Clean thetapered surface on thearbor with a clean
cloth. Make surethere are no foreignparticlessticking to the surface. The slightest piece of dirt on
this surface will prevent the arbor from seating
properly.This will cause the drillto "wobble."
2. Slide arbor into spindle on drillpress.
3. Push up on chuck/arbor assembly as you rotate
them. You will feel rectangular end of arbor slip
_otoa notch in the spindle.
SPINDLE

WARNING: MAKE SURE THE RECTANGULAR
END
OF THE ARBOR HAS SLIPPED INTO THE NOTCH
IN THE SPINDLE BEFORE GOING ON TO STEP 4.
FAILURE
TO FOLLOW
THIS DIRECTION
MAY
ALLOW THE CHUCK TO COME LOOSE DURING
OPERATION, FLY OUT, AND HIT THE OPERATOR.

ARBOR

CHUCK
SLEEVE

CHUCK
eDDY

SUPPORT
LOCK

4. Unlock support lock and raise fable so its about
two (2) inchesbelow tip of chuck.
5. Turn chuck sleeve clockwise and open jaws in
* chuck'completely.
6. Turn feed handles counterclockwise and force
chuck against table until arbor is secure.

CHUCK
SLEEVE

FEED
HANDLE

CHUCK

22

basic drill press operation
-

Follow the following mstructlons for operating your drdl
press tO get the best results and to m_mmize the likelihood of personal inlury
WARNING:
FOR YOUR OWN SAFETY, ALWAYS
OBSERVE THE SAFETY PRECAUTIONS HERE AND
ON PAGES 2, 3, AND 4.
f. Protection: Eyes, Hands, Face, Ears and Body
WARNING:
TO AVOID BEING PULLED INTO
THE SPINNING TOOL -1, Do NOT wear:
- gloves
- necktie
- loose clothing
-- jewelry
2, Do tie back long hair
a,

If any part of your drill press is missing, malfunctioning, has been damaged or broken..,
such
as the motor switch, or other operating control,
a safety device or the power cord..,
cease
operating immediately until the particular part
is properly repaired or replaced.

b.

Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece should unexpectedly shift or
your hand should slip.

Co

To avoid injury from parts thrown by the spring,
follow instructions exactly as given and shown
in adjusting spring tension of quill.

do

To prevent the workpiece from being torn from
your hands, spinning of the tool, shattering the
tool or being thrown, always properly support
your work so it won't shift or bind on the tool:
-- Always position BACKUP MATERIAL (use
beneath the workpiece) to contact the left
side of the column.
-- Whenever possible, position the WORKPIECE to contact the left side of the column-if it is too short or the table is tilted,
clamp solidly to the table, use table slots or
clamping ledge around the-outside edge of
the table.
-- When using a drill press VICE, always fasten
it to the table.

INSTALLING

DRILLS

,

Never do any wQrk 'FREEHAND"
(handholding wor&piece rather than supportIng it
on the tableL except when polishing.
- Securely lock Head and Support to Column,
Table Arm tO support, and Table to Table
Arm before operating drill press.
- Never move the Head or Table while the
tool is running
-- Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration.
-- If a workpiece overhangs the table such taht
it wilt fall or tip if not held. clamp it to the
table or provide auxiliary support.
--Use
fixtures
for unusual operations
to
adequately hold, guide and position workpiece,
-- Use the SPINDLE SPEED recommended
for the specific operation and workpiece material-check
the panel on the left side of
the head for drilling information; for accessories, refer to the instructions provided with
the accessories.
f. Never climb on the drill press Table, it could
break or pullthe entire drill press down on you.
g. Turn the motor Switch Off and put away the
Switch Key when leaving the drill press.
h. To avoid injury from thrown work or tool contact,
do NOT perform layout, assembly, or setup
work on the table while the cutting tool is rotating.
Use only accessories
designed for this drill
press to avoid serious injury from thrown broken parts or work pieces.
,
a. Holesaws must NEVER be operated on this drill
press at a speed greater than 400 RPM.
b. Drum sanders must NEVER be operated on
this drill press at a speed greater than 1800
RPM.
c. Do not install or use any drill that exceeds 7" in
length or extends 6" below the chuck jaws. They
can suddenly bend' outward or break.
d. Do not use wire wheels, router bits, shaper cutters, circle (fly) cutters or rotary planers on the
drill press.

IN CHUCK

With the switch off and the key removed, insert drill
into chuck far enough to obtain maximum GRIPPING
of the CHUCK JAWS...
the jaws are approx. 1" long.
When using a small drill do not insert it so far that the
jaws touch the flutes (spiral grooves) of the drill.
Make sure that the drill is CENTERED in the chuck
before tightening the chuck with the key.
JAWS

Tighten the drill sufficiently, so that it does not SLIP
while drilling.
Turn the chuck key clockwise
terclockwise to loosen.

to tighten--coun-

23

POSITIONING

TABLE

AND WORKPIECE
•_= <=

Lock the table to the column in a position so that the
tip of the drill is just a little above the top of the workpiece.
Always place a piece of BACK-UP MATERIAL (wood,
plywood...)
on the table underneath the workpiece.
This will prevent "splintering" or making a heavy burr
on the underside of the workpiece as the drill breaks
through. To keep the backup material from spinning
out of control, it must contact the left side of the column.
as illustrated.

_L

WORKPIECE

WARNING: TO PREVENTTHE
WORKPIECE OR THE
BACKUP MATERIAL FROM BEING TORN FROM
YOUR HAND WHILE DRILLING, POSITION THEM
AGAINST THE LEFT SIDE OF THE COLUMN. IF THE
WORKPICE OR THE BACKUP MATERIAL ARE NOT
LONG ENOUGH TO REACH THE COLUMN, CLAMP
THEM TO THE TABLE. FAILURE TO DO THIS
COULD RESULT IN PERSONAL INJURY.

BACK-UP
MATERIAL

For small pieces that cannot be clamped to the table,
use a drill press vise (Optional accessory.)
WARNING:
THE VISE MUST BE CLAMPED
OR
BOLTED TO THE TABLE TO AVOID INJURY FROM
SPINNING WORK AND VISE OR TOOL BREAKAGE.
WORKPIECE
DRILL PRESS
VISE

BOLT OR CLAMP
VICE SECURELY

4

TILTING

TABLE

To use the table in a bevel (hired) pos_l_on, loosen the
set screw under table bevel lock wath Hex "L" wrench.
Loosen bevel lock with adiustable wrench.
Tilt table to desired angle by reading bevel scale.
tighten bevel lock and set screw.

BEVEL

LOCK

Re-

BEVEL

WARNING: TO AVOID INJURY FROM SPINNING
WORK OR TOOL BREAKAGE,
ALWAYS CLAMP
WORKPIECE AND BACKUP MATERIAL SECURELY
TO TABLE BEFORE OPERATING
DRILL PRESS
WITH THE TABLE TILTED.
To return table to original position: loosen set screw
and bevel lock, tilt table back to 0° on bevel scale, and
retighten set screw--then tighten bevel lock.

HOLE LOCATION
Make a OENT in the workpiece where you want the
hole..• using aCENTER PUNCH or a SHARP NAIL.

SCALE

Before turning the switch ON, bring the drill down to
the workpiece lining it up with the hole location.

FEEDING
Pull down on the feed handles with only enough effort
to allow the drill to cut,

Feeding TOO SLOWLY might cause the drill to bum
•.. Feeding TOO RAPIDLY might stop the motor...
cause the belt or drill to SLIP...
tear the workpiece
LOOSE or BREAK the drill bit.
When drilling metal, it may be necessary to lubricate
the tip of the drill with motor oil to prevent burning the
drill tip.

adjustments
NOTCH

WARNING:
FOR
YOUR OWN
SAFETY
TURN
SWITCH "OFF" AND REMOVE PLUG FROM POWER
SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. TO AVOIO INJURY FROM THROWN PARTS
DUE TO SPRING RELEASE, FOLLOW INSTRUCTIONS CAREFULLY,
AND WEAR EYE GOGGLES.

QUILL

RETURN

BOSS
CAP
JAM

NUT

(OUTER)

SPRING

1. With the chuck at its highest possible position, turn
the depthscale clockwise until it stops and tighten
the depth scale lock. This will prevent the quill dropping while tensioning the spring.
2. Lower table for additional clearance•
3. Work from left side of Drill Press.
4. Place screwdriver in lower front notch of spring
cap, and hold it in place while loosening and removing jam [outer] nut only.
5. With screwdriver remaining in notch, loosen large
standard [inner] nut (approximately 1(8") until notch
disengages from boss on head. DO NOT REMOVE
THIS NUT.
6. Carefully turn screwdriver counter clockwise and
engage next notch in boss. DO NOT REMOVE
SCREWDRIVER.
7. Tighten standard nut with wrench only enough to
engage boss. Do not overtighten as this will restrict
quill movement.

NUT
(INNER)

.

Move stop nuts and depth pointer to upper most
position and check tension while turning feed handles.

9. If there is not enough tension on spring, repeat
steps 4-8 moving onlyONE notch each lime and
checking tension after EACH repetition.
10. Proper tensionisachievedwhen quill returnsgently
to full up positionwhen released from 3/4" depth.
11. When there is enoughtension after checking,replace jam nut and tightento standard nut.BUT do
not overtighten againststandard nut.
12. Check quill,while feeding to have smoothand unrestricted movement• If movement is too tight,
loosen jam nut and SLIGHTLY loosen standard
nut until unrestricted.Retighten jam nut.

maintenance

d_
cJ
C
C
(-

WARNING
FOR YOUR
OWN SAFETY,
TURN
SWITCH "OFF" AND REMOVE-PLUG FROM POWER
SOURCE OUTLET BEFORE MAINTAINING OR LUBRIC.a,TING YOUR DRILL PRESS.
Frequently blow out any dust that may accumulate inside the motor.
A coat of automobile-type was applied to the table and
column will help to keep,the surfaces clean.
WARNING: TO AVOID SHOCK OR FIRE HAZARD,
IF THE POWER CORD IS WORN OR CUT, OR DAMAGED IN ANY WAY, HAVE IT REPLACED
IMMEDIATELY.

C

._o
,,Q

lubrication

,-.,I

All of the BALL BEARINGS are packed with grease at
the factory. They require no further lubrication.
Periodically lubricate the gear and rack, table elevation
mechanism, the SPLINES (grooves) in the spindle, and
the RACK (teeth of the quill). See "Getting to Know
Your Drill Press."

WIRING

DIAGRAM
i

i,

4,t
0
4,t

Sears

Recommends

Drill Bits .........................
HoLd-Down and Guide ..................
Drill Press Vises ...................
Rotary Table ......................
Drill Press Mortising Kit .............
Hole Saw up to 2 1/2" dia. max .......
5 pc. Stop Collar Set ...............
15 Piece Drum Sanding Kit ..........

the Following

See Catalog
9-2457
See Catalog
See Catalog
See Catalog
See Catalog
See Catalog
See Catalog

Accessories

Clamping Kit ......................
See Catalog
Mortising Chisels and Bits ...........
See Catalog
Sanding Drums ................
9-2497 - 9-2498
Buffing Wheels up to 4" dia. max ......
See .Catalog
Power Tool Know-How Handbook .......
9-29117

Sears may recommend other accessories not listed in
the manual.
See your nearest Sears store or Catalog department
for other accessories.
Do not use any accessory unless you have received and
read complete instructions Ior its use.
26

trouble shooting
WARNING: FOR YOUR OWN SAFETY, TURN SWITCH
SOURCE OUTLET BEFORE TROUBLE SHOOTING.
• CONSULT

YOUR LOCAL SEARS SERVICE
, ,,.,

i

i

Noisy Operation

CENTER
i

TROUBLE

PROBABLE
1

i

"'OFF" AND ALWAYS

,

IF FOR ANY REASON

i

REMEDY
i i

ii

1. Incorrect belt tension,

i

i

i

i

i,

,

,

i

i

,i

1. Adjust tension, See section
"ASSEMBLY--TENSIONING
BELT,'"
2. Lubricate spindle, See "Lubrication"
section.
3. Checking tightness of retaining nut on
pulley, and tighten if necessary.
4. Tighten setscrews in pulleys.

3. Loose spindle pulley.
4. Loose motor pulley.
1. Incorrect speed.

1. Change speed. See section "Getting
To Know Your Drill Press"...
DRILLING SPEED.
2. Retracl drill frequently to clear chips.

2. Chips not coming out
of hole.
3. Dull Dr!ll.
4. Feeding too slow.
5. Not lubricated.

Drill leads off...
hole not round.

MOTOR WILL NOT RUN.

,i

CAUSE

2. Dry Spindle.

Drill Burns

REMOVE PLUG FROIM POWER

3. Resharpen drill.
4. Feed fast enough.., allow drill to cut.
5. Lubricate drill. See "Basic Drill Press
Operation" section.

1. Hard grain in wood or
lengths of cutting
lips and/or angles
not equal.
2. 8entdrill bit.

1. Resharpen d rill correctly.

2. Replace drill bit.

Wood splinters on
underside,

!.

No "back-up material"
under workpiece.

Workpiece torn
loose from hand.

1. Not supported or
clamped properly.

1. Support workpiece or clampit... See
"Basic Drill Press Operation" section.

Drill Binds in
workplece.

1. Workpiece pinching drill
or excessive feed pressure.
2. Improper belt tension.

1. Support workpiece or clamp it... See
"Basic Drill Press Operation" section.
2. Adjust tension... See section
"ASSEMBLY--TENSIONING
BELT."

Excessive drill
runout or wobble.

1. Bent drill.
2. Worn spindle bearings.
3. Drill not properly
installed in chuck.
4. Chuck not properly installed.

1. Use a straight drill.
2. Replace bearings.
3. Install drill properly.,. See "Basic
Drill Press Operation" section.
4. Install chuck properly..,
refer to
"Unpacking and Assembly Instructions
... INSTALLING THE CHUCK."

Quill Returns
too slow or too
fast.

1. Spring has improper tension.

1. Adjust spring tension... See section.
"Adjustments--Quill
Return Spring."

Chuckwill not stay
attached to spindle
it falls off when
trying to install it.

1.

1. Use"back-up material".,. SeeBasic
Drill Press Operation" section.

Dirty, grease, or oilon the
tapered insidesurfaceof chuckor on the spindlestapered
surface.

27

1,

Using a household detergent-clean the
tapered surface of the chuck and spindle to
remove all dirt, grease and oil.

PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS
MODEL NO. 113.213!70

"10

47

;:3.

10

48
49
51

52

5O
43
3
43
42

41
5

44
4

1

m

13
14

15
16

31

/

32

\
23

25
26

22

3O

28

21

28

2O

/
19

FIGURE

1

14
14

24

27

17

PARTS

LIST FOR CRAFTSMAN
17" DRILL
MODEL NO. 113.213170

Always order by Part Number--Not

PRESS

by Key Number

FIGURE 1 PARTS LIST
Key
No.

Part
No.

_11 I

= i

I

1
2

81732O
817391

3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

817316
817303
817347
817774-1
817343
817346
817300
817299
817344
813249-128
STD852005
816755
817369
816755-2
816113
817354
815863
817352
818511
816755-6
817308

24
25
26
27
28
29
30

STD841015
817304817305
817306
817307,
STD541150
STD541350

Any Attempt
Technician.

Key
No.

Description
i

ii

"O
Pad
No.

Description

0t}

i

Knob-Motor Adjusting
Screw-Socket Set
M10x 1.5-12
Handle-Belt Tension
Pin-Stop
Shaft-Pinion
Ring-Depth Stop w/Scale
Lock-Depth Screw
Hub _11i'_ _ 8'
Guide Scale
Knob
Rod
Pin-Roll 5x 16
* Lockwasher-Ext M5
Screw-Pan CR M5 x 0.8-8
Box-Switch
Screw-Pan CR M5 x 0.8-15
Swdch-Locking
Switch-Rocker
Key-Switch
Cover-Sw_tch Plate
Lead-Asm. 3"
Screw-Pan CR M5 x 0.8-16
Screw-SL Special
10x 1.5-27
* Nut-Hex M10 x 1.5
Seat-Spring
Retainer-Spring
Spring-Torsion
Cap-Spring
*Nut-Hex 1/2-20
*Nut-Hex Jam 1/2-20

31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
-

817778-3
817321
813317-8
813317-7
813317-6
60475
817329
STD375008
817694
63418
817337
STD835020
STD551031
817336
817328
STD840812
817298
STD841217
STD551150
817338
STD835016
817317
507865
507866
507867
507864
SP5188

Head w/PoInter and Tr=m
Socket-Bulb Asm.
Wrench Hex "'L" M5
Wrench Hex "L" M4
Wrench Hex "L" M3
Tie-Wire
Cord-Power w/Plug
* Connector-WIre
Screw-Pan CR M6 x 1.0 x 12
Clamp-Cord
Support-Motor Bracket
* Screw-Hex HD M8 x 1 25-20
,,Washer 21/64 x 7/8 x 3/64
Mount-Motor
Cord-Motor
*Nut-Hex M8 x 1 25
eMotor
*Nut-Hex M12x 1.75
* Lockwasher 1/2
Support- Motor Bracket
*Screw Hex HD M8 x 1.25-16
Lever-Adjusttng
Bag of Loose Parts
(Not Illustrated)
Bag of Loose Parts
(Not illustrated)
Bag of Loose Parts
(Not Illustrated)
Box of Loose Parts
(Not illustrated)
Owners Manual
(Not Illustrated)

to Repair This Motor May Create a Hazard Unless Repatr is Done by QualfJed Service

Repair Service is Available at Your Nearest Sears Store.
* Standard

Hardware

Item -- May Be Purchased

Locally,

RepairParts

repair parts
PARTS LIST FOR CRAFTSMAN 17" DRILL PRESS
MODEL NO. 113.213170

17

12

\

I
8

11
10

L
9

Always order by Part Number--Not

FIGURE

Key
No.

Part
No.

1
2

817319
STD315255

_

817318
STD304290

_

817327"
817333
817335
817779-4
817358

Description
iii

7
8
9

by Key Number

2

Key
No.

Part
No.

10
11
12
13
14
15
16
17

817391-2
817331
817325
816755-3
818532
817332
STD315225
STD304270

Description

i

i

Ring-Retaining
* Bearing-Ball 25mm
Spacer-Bearing
* Belt-"V" 1/2x29
Nut-Pulley
Pulley-Spindle
Insert-Pulley
Guard-Pulley w/Labels
Screw-RD HD Washer
M6x 1.0-16

* Standard Hardware item -- May Be Purchased Locally.

30

Screw-Set M8 x 1.25-8
Pulley-Motor
Knob
Screw-Pan HD M5x 0.8-12
Pivot-Idler
Pulley-Center
* Bearing Ball 15mm
* Belt-"V" 1/2 x 27

repair parts
PARTS

LIST FOR CRAFTSMAN
17" DRILL
MODEL NO. 113.213170

PRESS

OJ

1

5

10

Always order by Part Number--Not

FIGURE

Key
No.

Part
No.

1
2
3
4
5
6

817309
817310
817311
STD315235
817314
817342

3

Part
No.

Key
NO.

Description
i

II

by Key Number

i

i

7
8
9
10
11
12

Nut-Lock
Ring-Locking
Washer
* Bearing-Ball 17ram
Washer-Rubber
Tube-Quill

* Standard Hardware item -- May Be Purchased

Locally.

31

Description
i

817339
817340
817341
817326
817359
STD315255

i

i

Key-Chuck
Chuck
Arbor
Key-Drift
Spindle
* Bearing- Ball 25mm

i

ii

repair parts

t.n

-=

PARTS

LIST FOR CRAFTSMAN
17" DRILL
MODEL NO. 113.213170

PRESS

o..
._L
(1)

jl

18

Ii

3

8

10

Always order by Part Number--Not by Key Number
FIGURE

Key
No.

Part
No.

Description

4

Key
No.

Part
No.

10
11
12
13

817361
817360
STD836040
817391

14
15
16
17
18
19

817285
817351
817294
817776-1
817349
817288

iii i

1

817391-1

2
3
4

817286
817350
817348

6
7
8

817366
817290
817392
817777-2

Description

IIII

Screw-Hex Soc Set
M6x 1,0-10
Collar.Rack
Gear-Helical
Crank
Table
Clamp-Table
Screw-Hex HD
5/8-11 x 1-1/4
Arm-Table w/Scale

32

Base
Support-Column
* Screw-Hex HD M 10 x 1.5-40
Screw-Hex Soc Set
M10x 1,5-12
Tube-Column
Rack
Clamp-Column
Support-Table w/Indicator
Worm-Elevation
Pin-Gear

NOTES

33

NOTES

I

I

34

NOTES

35

f

/-

8EARS
owner's
manual

MOTORIZED

47-1NCH
FLOOR MODEL DRILL PRESS

SERVICE

Now thatyou have purchased your 17-inchDrill
Press,
should
a need ever exist
forrepairpartsor service,
simplycontact
any Sears ServiceCenter and most Sears,Roebuck and Co.
stores,
Be sureto provide allpertinentfactswhen you call
or visit.

MODEL NO.
113.213170

The model number of your 17-inchDrill
Presswill
be found
on a plateattached to the rearof the head.

DRILL PRESS WITH
MAXIMUM
DEVELOPED
1 I/2 HP MOTOR

HOW TO ORDER
REPAIRPARTS

WHEN ORDERING REPAIRPARTS,ALWAYSGIVE THEFOLLOWING
INFORMATION:
PARTNUMBER

PARTDESCRIPTION

MODEL NUMBER
113.213170

NAME OF ITEM
MOTORIZED 17-INCH
FLOOR MODEL DRILL PRESS

All parts listed may be ordered from any Sears Service Center
and most Sears stores. If the parts you need are not stocked
locally, your order willbe electronically transmitted to a Sears
Repair Parts DistributionCenter for handling.

J

J

Sold by SEARS, ROEBUCK AND CO., Chicago,
Part No. 5P5188

Form No. SP5188-3

IL 60684

U.S.A.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 36
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sat Mar 29 05:18:05 2014
Author                          : 
Title                           : 
Subject                         : 
EXIF Metadata provided by EXIF.tools

Navigation menu