Craftsman 113213850 User Manual 15 INCH DRILL PRESS Manuals And Guides L0803156

CRAFTSMAN Drill Press Manual L0803156 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

User Manual: Craftsman 113213850 113213850 CRAFTSMAN CRAFTSMAN 15 INCH DRILL PRESS - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 15 INCH DRILL PRESS #113213850. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 15 INCH DRILL PRESS Manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

SAVE THiS MANUAL
FOR FUTURE REFERENCE

MODEL NO.
113.213850
DRILL PRESS WiTH
112 HP MOTOR

Serial
Number
Model and serial
number may be found
at the rear of the head.
You should

record both

model and serial number
in a safe place for
future use.

MOTORIZED

15 INCH
FLOOR MODEL DRILL PRESS
• assembly
e operating
= repair parts

CAUTION:
Read GENERAL
and ADDiTiONAL
SAFETY
iNSTRUCTiONS
carefully

Sold
Part No. 71329

by SEARS,

ROEBUCK

AND

CO.,

Form No. SP4738

Chicago,

IL. 60684

U.S.A.
2/84

FULL ONE YEAR WARRANTY

ON CRAFTSMAN

DRILL

PRESS

If within one year from the date of purchase, this Craftsman Drill Press fails due to a
defect in material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT
THROUGHOUT THE UNITED STATES.
THiS WARRANTY
STATES.

APPLIES

ONLY WHILE THIS PRODUCT

This warranty gives you specific
vary from state to state.

IS iN USE IN THE UNITED

legal rights, and you may also have other

rights

which

SEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, iL 60684

general safety instructions
.

KNOW YOUR POWER TOOL
Read and understand the owner's
labels affixed to the tool. Learn
tion and limitations
as well as
potential hazards peculiar to this

for power tools

manual and
its applicathe specific
tool.

GROUND ALL TOOLS
This tool is equipped witl_ an approved 3conductor cord and a 3-prong gounding type
plug to fit the proper grounding type receptacle. The green conductor in the cord is the
grounding wire. Never connect the green wire
to a live terminal.
KEEP GUARDS IN PLACE
In working order, and rl proper
and alignment.

adjustment

REMOVE ADJUSTING KEYS AND
WRENCHES
Form a habit of checking to see that keys
and adjusting
wrenches are removed from
tool before turning it on.
KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.
Floor must not be slippery
due to wax or
sawdust.
AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or expose them to rain. Keep work area
well lighted.
Provide adequate surrounding
work space.
KEEP CHILDREN AWAY
All visitors should be kept a safe distance
from work area.

MAKE WORKSHOP KID-PROOF
with padlocks,
master switches,
or by
removing starter keys.
9. DON'T FORCE TOOL
tt will do the job better and safer at the rate
for which it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment
to do a job it
was not designed for.
11, WEAR PROPER APPAREL
Do not wear loose clothing, gloves, r_eckties

or jewelry (rings, wrist watches) to get caught
in moving parts. Nonslip footwear is recommended. Wear protective
hair covering
to
contain long hair. Roll long sleeves above the
elbow.
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANS!
Z87.1) at all times. Everyday eyeglasses only
have impact resistant lenses, they are NOT
safety glasses. Also, use face or dust mask if
cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of
operation.
13. SECURE WORK
Use clamps or a vise to hold work when practical, it's safer than using your hand, frees
both hands to operate t0ol.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
16. DISCONNECT TOOLS
Before servicing; when changing accessories
such as blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before
plugging in.
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended accessories.
Follow the instructions
that
accompany
the accessories.
The use of improper accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
Do not store materials above or near the tool
such that it is necessary to stand on the too!
to reach them.
20. CHECK DAMAGED PARTS
Before further use of the tool,

a guard

other part

that is damaged should be carefully checked to ensure that it will operate properly and perform
its intended
function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions
that may affect its
operation.
A guard or other part that is
damaged
should
be properly
repaired
or
replaced.

additional

safety instructions

WARNING: FOR YOUR OWN SAFETY, DO NOT
ATTEMPT TO OPERATE YOUR DRILL PRESS
UNTIL IT !S COMPLETELY
ASSEMBLED AND
iNSTALLED
ACCORDING
TO THE INSTRUCTIONS...AND
UNTIL YOU HAVE READ AND
UNDERSTAND THE FOLLOWING:

1.
2.
3.
4.
5.

Page
General Safety instructions for Power Tools. 2
Getting to Know Your Dri!l Press ...........
12
Basic Drill Press Operation ................
15
Adjustments ..............................
t7
Maintenance ..............................
18

6. Stability of Dri!l Press
The drill press should be bolted to the floor;
an alternate is to securely bolt a piece of
1t2" exterior plywood to the underside of the
Base, extending to both sides, and to rear if
desired.
If the workpiece is too large to support
one hand, provide an auxiliary support.
,

with

Location
The drill
press should
be positioned
so
neither the operator nor a casual observer is
forced to stand in line with a potential
Kickback.

Kickback
A kickback
occurs when the workpiece
is
suddenly thrown in the OPPOSITE direction
to the DIRECTION
OF FEED; THIS CAN
CAUSE SERIOUS
INJURY.
Kickbacks
are
most commonly caused by:
a. Relaxing your grip of the workpiece while
surfacing or planing.
b. Taking too heavy a cut while surfacing or
planing.
c. Ignoring the instructions
for surfacing or
planing.

Protection: Eyes, Hands, Face, Ears, Body
WARNING:
FOR YOUR OWN SAFETY, DO
NOT WEAR GLOVES, NECKT!E OR LOOSE
CLOTHING,
AND TiE BACK LONG HAiR
WHEN OPERATING DRILL PRESS.
a. if any part of your drill press is malfunctioning,
has been damaged or broken...
such as the motor switch, or other operating control, a safety device or the power
cord..,
cease operating immediately until
the particular part is properly repaired
or
replaced.

2t. DIRECTION OF FEED
Feed work into a blade or cutter against the
direction
of rotation of the blade or cutter
only.
22. NEVER LEAVE TOOL RUNNING
UNATTEN DED
Turn power off. Don't leave
comes to a complete stop.

tool

until

for drill presses
ANSI Z87.1, and a face mask if operation
is dusty. Wear ear plugs or muffs during
extended periods of operation.
c. Never place your fingers
in a position
where they could contact the drill or other
cutting
tool if the workpiece
should
unexpectedly
shift.
d. To avoid injury, follow instructions
exactly
as given and shown in adjusting
spring
tension of quill.
e. ALWAYS position backup material to contact the left side of the column. POSITION
workpiece
to butt against
the column
whenever
possible--if
it is too short,
clamp solidly to the Table. Use table slots
or clamping ledge around outside edge of
Table. This is to prevent the drill bit from
grabbing the work from your hands. This
action would cause the workpiece to spin
with the drill, and could cause serious
injury. A drill press vise must be fastened
to the table.
f. Never perform any operation
"free-hand"
.(hand-holding
workpiece
rather than support it on the Table), except when polishing -- Wear Safety Goggles!
g. Securely lock Head and Support to Co!umn, Arm to Support, and Table to Arm
before operating Drill Press.
h. Never perform any operation
by moving
the Head or Table with respect to one
another.
i.
Before pulling the motor switch "ON", be
positive
the belt guard
is closed,
the
Chuck is installed properly, and the drill or
other cutting tool is securely clamped in
the chuck.
j.
Before
starting
the operation,
jog the
motor switch to be sure the drill or other
cutting toot does not have excessive runout or cause vibration.
k. Do not operate the Dril! Press unless the
Depth Stop and Stop Nut are installed.
I. Use the spindle speed recommended
for
the specific
operation
and
workpiece
materia! - refer to panel on left side of
the Head for drilling
information;
for
accessories,
refer to the instruction
sheets
that accompany the accessories.
m. tf workpiece overhangs the Table such that
it will fall to floor if unsupported,
clamp it
to the Table or provide auxiliary support,

additional safety instructions for dril! presses
n.

Use fixtures
for unusual operations to
adequately hold, guide and position workpiece for best quality and minimum hazard.
o. Never climb on the drill press Table.
p. Turn the motor Switch off and put away
the Switch
Key when leaving the drill
press.
q. DO NOT perform layout, assembly, or set.
up work on the table while the cutting tool
is rotating.
r. ALWAYS
clamp
workpiece
securely
to
table when table is tilted.
10. Use only accessories designed for this drill
press.
a. Holesaws must NEVER be operated on
this drill press at a speed greater than 400
RPM.
b. Drum sanders must NEVER be operated
on this drill press at a speed greater than
2300 RPM.
c. Do not install or use any drill that exceeds
7" in length or extends
6" below the
chuck jaws.
d. Do not use wire wheels,
router
bits,
shaper cutters, or circle (fly) cutters on
this drill press.
11. Note and Follow the Safety Warnings and
Instructions that Appear on the Panel on the
Left Side of the Head:
[DANGER 1
FOR YOUR OWN SAFETY:
1. READ
AND
UNDERSTAND
OWNERS
MANUAL
BEFORE OPERATING MACHINE.
_2. WEAR SAFETY GOGGLES.
3. DO NOT WEAR
GLOVES,
NECKTIE,
OR LOOSE
CLOTHING, TIE BACK LONG HAIR.
4. SECURELY CLAMP WORK TO TABLE IF IT IS TOO
SHORT
TO CONTACT
THE COLUMN
WHEN
IN
OPERATING POSITION.
5. USE RECOMMENDED
SPEED FOR DRILL, ACCESSORY, AND WORKPIECE MATERIAL.
6. SECURELY
LOCK HEAD AND SUPPORT TO COL,
UMN, ARM TO SUPPORT,
AND TABLE TO ARM
BEFORE OPERATING DRILL PRESS.
7. USE ONLY RECOMMENDED
ACCESSORIES.

12.This Drill
below:

Press
300
375
525
560
700
860

has 12 speeds

RPM
RPM
RPM
RPM
RPM
RPM

1450
1530
2000
2200
3400
4600

listed

RPM
RPM
RPM
RPM
RPM
RPM

See right side of Head for specific
of belts on pulleys.

placement

13. Think Safety. Safety is e combination
of
operator common sense and alertness at all
times when the drill press is being used.
WARNING:
DO NOT ALLOW
FAMILIARITY
(GAINED
FROM
FREQUENT
USE OF YOUR
DRILL PRESS) TO BECOME COMMONPLACE.
ALWAYS
REMEMBER
THAT
A CARELESS
FRACTION OF A SECOND IS SUFFICIENT TO
INFLICT SEVERE INJURY.
The operation
of any power tool can result in
foreign
objects
being thrown
into the eyes,
which can result n severe eye damage. Always
wear safety goggles corn;)lying with ANSI Z87.1
(shown on Package) before commencing
power
tool operation.
Safety Goggles are available at
Sears retail or catalog stores.

WEAR

YOUR

unpacking and checking contents
CONTENTS

Page
General Safety instructions for Power Tools .... 2
Additional Safety Instructions for Drill Presses . 3
Unpacking and Checking Contents .............
4
Table of Loose Parts ..........................
5
Motor Specifications and Electrical
Requirements .................................
6
Assembly .....................................
7
Assembly of Column and Table Hardware...
7
Installing the Table ..........................
7
Installing the Head ..........................
8
Installing Feed and Tension Handles .........
8
installing the Chuck .........................
g
Tensioning Belt ............................
10
Installing Light Bulb .......................
11
Adjusting the Table Square to Head ........
11
Adjusting the Pointer ......................
12

Getting to Know Your Drill Press ..............
Removing the Chuck .......................
Drilling to Depth ...........................
Basic Drill Press Operation ...................
Installing Drills ............................
Positioning Table and Workpiece ...........
Tilting Table ...............................
Hole Location .............................
Feeding ...................................
Adjustments
.................................
Depth Scale ................................
Quill Return Spring .........................
Maintenance .................................
Lubrication
..................................
Recommended
Accessories
..................
Trouble Shooting .............................
Repair Parts ..................................

12
15
15
15
16
16
16
17
17
17
17
17
18
18
18
19
20

TOOLS

UNPACKDNG AND CHECKnNG
CONTENTS
Model
No.
one carton
motor.

113.213850
is
and includes

shipped
complete
in
a 1!2 HP 1725 RPM

COIVlS_NA_

Separate
all parts
from
packing
materials
and
check
each one with the "Table
of Loose
Parts"
to make
certain
all items
are accounted
for,
before discarding
any packing
material.

COMBINATION
DRAW LIGHT
LiNE ON BOARD

If any parts
are missing,
do not
attempt
to
assemble
the drill press, plug in the power cord
or turn the switch
on until the missing
parts are
obtained
and installed
correctly.

SHOULD
SQUARE

_em
A
B
C
D
E

OF LOOSE

_$_======_

PARTS

Description
Column Assembly
.....................
Head Assembly ........................
Table ..................................
Base ..................................
Owners Manual ........................
Box of Miscellaneous
Small Parts, Part # 71388
Consisting of the Following:
Chuck .................................
Rod ...................................
Support Lock ..........................
Chuck Key 16MM ......................
Table Crank Assembly
.................
*Knob ..................................
*Tension Rod ...........................
*Tension Rod Knob .....................
*Screw, Pan Hd. 10-32x3t8 ...............
*Pointer ................................
*Set Screw Wrench !18 ..................
*Set Screw Wrench 3/16 .................
*Bolts, Hex Hd. 3/8-16x11/2 ...............
* Lockwasher 3!8 ........................
*Hex Soc. Set Screw 3!8-16xl12 ..........
*Switch Key ............................

*Parts Contained

MUST BE TRUE
STRAIGHT EDGE OF
BOARD 3/4" THICK
THIS EDGE MUST BE
PERFECTLY STRAIGHT

BE NO GAP OR OVERLAP WHEN
iS FLIPPED OVER IN DOTTED POSITION

MEDIUM
SCREWDRSVER

or similar

Apply a coat of automobile wax to the table.
Wipe all parts thoroughly
with a clean dry cloth.

TABLE

SQUARE

ALONG THiS EDI_,_.__

Remove
the protective
oil that is applied
to the
table and column.
Use any ordinary
household
type grease and spot remover.

CAUTgON: Never use gaso_Nne, naptha
highly vo_atine somvertts.

NEEDED

A
Qty.
1
1
1
1
1

1
3
1
1
1
3
1
1
1
1
1
!
4
4
2
1

In Loose Parts Bag; Part No. 71389

84NCH ADJUSTABLE
WRENCH

motor specifications and electrical requirements
MOTOR SPECIFICATIONS
This drill press is designed to use a 1725 RPM
motor only. Do not use any motor that runs faster
than 1725 RPM. It is wired for operation on 110120 volts, 60 Hz., alternating current.
CAUTION: Do not use blower or washing machine
motors or any motor with an automatic reset
ovedoad protector as their use may be hazardous.
CON NECTING TO POWER SOURCE OUTLET
This machine must
protect the operator

De grounded
from electric

while n use to
shock.

Plug power cord into a 110-120V properly grounded type outlet protected by a 15-amp. dual element time delay or Circuit-Saver
fuse or circuit
breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY
A QUALIFIED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING
OR REMOVING THE PLUG TO OR FROM THE
OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THiS
POWER TOOL CAN iNCUR THE POTENTIAL
HAZARD OF ELECTRICAL SHOCK, PARTICULAR.
LY WHEN USED iN DAMP LOCATIONS, iN PROXIMITY TO PLUMBING. IF AN ELECTRICAL SHOCK
OCCURS THERE IS THE POTENTIAL OF A SECONDARY HAZARD SUCH AS YOUR HANDS CON.
TACTING THE CUTTING TOOL.
If power cord is worn or cut, or damaged
way, have it replaced immediately.

This power tool is equipped with a 3-conductor
cord and grounding
type plug which
has a
grounding
prong, approved
by Underwriters'
Laboratories and the Canadian Standards Association. The ground conductor has a green jacket
and is attached to the tool housing at one end
and to the ground prong in the attachment
plug
at the other end.
This plug requires a mating 3-conductor
ed type outlet as shown.

ground-

If the outlet you are planning to use for this
power tool is of the two prong type, DO NOT
REMOVE OR ALTER THE GROUNDING PRONG
Ik ANY MANNER. Use an adapter as shown and
always connect the grounding
tug to known
ground.
It is recommended that you have a qualified electrician replace the TWO prong outlet with a properly grounded THREE prong outlet.
An adapter as shown below is available for connecting plugs to 2-prong receptacles. The green
grounding
lug extending
from the adapter must
be connected to a permanent ground such as to
a properly grounded outlet box.

SCR_\
3-PRONG

GROUNDING

LUG

S,_

MAKE SURE THIS IS

in any

ADAPTER

3-PRONG
PLUG

NOTE: The adapter illustrated
is for use only if
you already have a properly grounded
2-prong
receptacle. Adapter is not allowed in Canada by
the Canadian Electrical Code.

GROUNDING
PRONG

PROPERLY
GROUNDED
OUTLET

tf your unit is for use on less than 150 volts, it
has a plug that looks like above.

The use of any extension cord will cause some
loss of power. To keep this to a minimum and to
prevent over-heating and motor burn-out, use the
table below to determine the minimum wire size
(A.W:G.) extension cord. Use only 3 wire extension cords which have 3 prong grounding type
plugs and 3-pole receptacles
which accept the
tools plug.
Extension

Cord Length

Upto - 100 Ft.
100 - 200 Ft.
200 - 400 Ft.

Wire Size A.W.G.
16
14
10

assemb0y
WARNING: FOR YOUR OWN SAFETY, NEVER
CONNECT PLUG TO POWER SOURCE OUTLET
UNTIL ALL ASSEMBLY STEPS ARE COMPLETED.

COLUMN
SUPPORT

I
J

ASSEMBLY OF COLUMN AND TABLE
HARDWARE
1.

Position
covering

Remove protective
sleeve from column tube
and discard. Place column assembly on base,
and align holes in column support with holes
in base.

Locate four (4) 318-16Xll/2 bolts and four (4)
3/8 Iockwashers among loose parts bag.
Install a Iockwasher
and bolt in each hole
through column support and base, and tighten with adjustable wrench.

base on floor.
and discard.

Remove

protective

Locate table crank assembly, support lock,
and set screw wrench among loose parts.

Install table crank
screw with wrench

Install support lock from left side into table
support and tighten by hand.

assembly
provided.

and tighten

TABLE
SUPP

TABLE

SUPPORT

set

Handle should turn freely when raising or
lowering
table.
If adjustment
is needed,
loosen jam nut, with a screwdriver
loosen
bolt handle until there is play between jam
nut and handle. Tighten jam nut securely
while holding bolt handle with screwdriver.

SUPPORT
LOCK
I

TABLE

-..-.-.,-_L._-_

C RAN K

._
,

COLUMN
COLLAR

Position column collar over rack and tighten
set screw in collar with wrench provided.
Allow sufficient
movement
to prevent rack
from binding when moving table to the side.

_'-_

IT]I

HANDLE

','
_/"_'7_f

COLUMN
(4_T
f

"--_

TABLE

TABLE
SUPPORT

INSTALLONG THE TABLE

TABLE
CRANK

Loosen support lock and raise table support
by turning table crank clockwise
until support is at a working height level. Tighten support lock.
SUPPORT
LOCK

assembly

TABLE

i i _ii_!i_iii_i_
_ _i:ii
,J

Remove protective
covering from table and
discard. Place table in support and tighten
table lock (located under table) by hand.

SUPPORT

INSTALLING

"J1

THE HEAD

CAUTION:
THE HEAD ASSEMBLY
WEIGHS
ABOUT 60 POUNDS. CAREFULLY LiFT HEAD.
HEAD

Remove protective
bag from head assembly
and discard. Carefully lift head above column
tube and slide it onto column into position,
Align head with table and base.

H EAD
LOCKS

Locate two (2) 318-16x112 set screws
loose parts bag.

Install set screws in right side of head to lock
head into position, and tighten with wrench
provided.

000

among

HEAD

FLATS _.
-%

FEED
,_ ROD

INSTALUNG
1.
2.

FEED AND TENSION

HANDLES

_ _
HUB

Locate three (3) rods and three (3) knobs
among loose parts.
Screw a knob on each rod, then screw the
other rod end into the threaded holes in the
hub and tighten. Use an adjustable
wrench
on the flats provided to tighten the feed rods
securely.

FEED
KNOB

LEVER
_HAFT

Locate one (t) tension
among loose parts.

rod and one (1) knob

Screw the knob on the rod, then
rod into the lever shaft.

screw

BELT
ENSION
HANDLE

the

\
POINTER

Locate one (1) 10-32x3/8 pan hd. screw
one (1) pointer among loose parts bag.

and

Install screw through pointer into table support, and tighten with screwdriver.
/

SCREW

,,/J

INSTALLING

THE CHUCK

Clean out the TAPERED HOLE in the chuck;
clean the spindle nose with a clean cloth.
Make sure there are no foreign
particles
sticking to the surfaces. The slightest piece
of dirt on the spindle nose or in the chuck
will prevent the chuck from seating properly.
This will cause the drill to "wobble."

Apply a light film of oil such as Sears household oil to the spindle nose.

Place
screw
go.

LOCKING

COLLAR

the chuck on the spindle
nose and
the locking collar up as far as it wilt

-" jJ
9

assembly
3/16" ROD
OR DRILL

Insert a piece of 114" dia. STEEL ROD in to
one of the holes in the chuck body.

LOCKING
;OLLAR
CHUCK
SLEEVE

Insert 3/]6" dia. rod or drill into one of the
holes in the collar...TURN
IT IN THE
DIRECTION OF ARROW UNTIL IT IS TIGHT.

To remove chuck, turn the collar in the opposite direction
until the chuck is ejected
from the spindle.

CHUCK
BODY

114" ROD
OR DRILL

TENSIONING

BELT

NOTE: The Drill Press is shipped with the belt
installed,
but it should be properly tensioned
before use.
1. Lift guard from right
on hinge.
2,

side and leave opened

Release Belt Tension Lock Handles
on each side of Drill Press head.

BELT
TENSION
LOCK
HANDLE

located

BELT
TENSION
HANDLE

Loosen Belt Tension Handle by turning
wise.

Choose speed for drilling
operation,
and
move belt to correct
position
for desired
speed.

NOTE: Refer to chart on side of Drill
Recommended Drilling Speeds.

clock-

Press for
\

Apply tension to belt by turning Belt Tension
Handle counter clockwise until belt has moderate tension on pulleys.

Tighten
Belt Tension
Lock Handles.
Belt
should deflect
approximately
1/2 inch by
thumb pressure at center of belt.

Close belt guard.

If belt
tension.

INSTALLING
1.

slips

while

drilling,

readjust

belt

LIGHT BULB

Install a Hght bulb (not larger than 60 watt)
into the socket inside the head.

%
\

ADJUSTING THE TABLE SQUARE TO HEAD
NOTE: The combination
square must be "true".
See "Unpacking and Checking Contents"
section
for method.
t.

insert a precision ground steel rod approximately 3" long into chuck and tighten.

With table raised to working height and locked on column, place combination
square flat
on table beside rod.

If an adjustment is necessary, loosen the set
screw
under
bevel lock with
set screw
wrench, then loosen the table bevel lock with
adjustable
wrench. [These adjustments
are
located under the table].

Align the table square to the rod by tilting
arm until square and rod are in line.

Retighten

table bevel lock nut.

Retighten

set screw.

ARM
TABLE

I/_I
I I k""C_

o t

_
I

BEVEL
LOCK

assembly

TABL

SCALE
POINTER

ADJUSTING POINTER
1.

With the table squared to the head, the table
bevel pointer should be adjusted.

Loosen screw in pointer with screwdriver.
and move pointer to "0" position on scale.
Retighten screw.

SCREW

getting to know your drill press
24
27
DRILL
FEED SPRING
ADJUSTMENT
BELT

3
TENSION

FEED
SPRING

"ON-OFF"

SWITCH

DEPTH SCALE
DEPTH

POINTER

BELT GUARD
/

LIGHT "ON-OFF"
SWITCH

2
BELT TENSION
HANDLE

LOCK HANDLE

TENSION
LOCK HANDLE

FEED STOP

CHUCK LOCKING
COLLAR

HEAD LOCK

COLUMN

SPRING

CaR

COLLAR

FEED HANDLE

RACK

15
TABLE BEVEL

17
TABLE

16
7

]-ABLE LOCK

TABLE CRANK

SUPPORT

ARM/

BEVEL SCALE

TABLE SUPPORT

12
C(

SPLINES
(GROOVES)
QUILL AND SPINDLE ASSEMBLY
INSIDE OF DRILL PRESS

COLUMN

SPINDLE

10
/BASE

RACK
_EETH)

This Drill Press has 12 speeds as listed
below:
300RPM
1450RPM
375RPM
1530RPM
525RPM
2000RPM
560RPM
2200RPM
700RPM
3400RPM
860RPM
4600RPM

®
,,,._,

SPINDLE

SPEEDS

iN R.P.M.

3OO

375

525

560

700

860

1450

1530

2000

2200

3400

4600

¢_

o ,

Seeright side of Headfor specificplacement
of beltson pulleys.

BELT GUARD ...Covers
pulleys
during operation of drill press.

and

mounting

BELT TENSION
HANDLEoo.Turn
handle
counter c_ockwise to apply tension to belt,
turn handle clockwise to release belt tension.

BELT TENSION LOCK HANDLES...
Tightening handles locks motor bracket support and
BELT TENSION HANDLE to maintain correct
belt distance and tension.
HEAD LOCKS..,
Lock the head to the column. ALWAYS have them locked in place
while operating the drill press.

COLUMN COLLAR...
Holds the rack to the
column. Rack remains movable in collar to
permit table support movements.

RACK...
Combines with gear mechanism to
provide easy elevation of table by hand operated table crank.

SUPPORT LOCK...Tightening
locks table
support to column. Always have it locked in
place white operating the Drill Press.

TABLE CRANK...
Turn clockwise to elevate
table. Support lock must be released before
operating crank.

TABLE
support

SUPPORT...
Rides
arm and table.

14. ARM ...Extends

belt

column

15. TABLE

BEVEL LOCK...
Locks
any position from 0°-45 °.

support

LOCK...
Table can be rotated
ous positions and locked.

17. TABLE...

Provides
port workpiece.

working

for

the table i_

16. TABLE

surface

in var'_-

to sup-

18. FEED HANDLE...

For moving the quill up o_
down. One or two may be removed if necessary whenever
the workpiece
is of suoh
unusual shape that it interferes
with the
handles.

19. CHUCK.,,
Holds
mended accessory
tions,

drill bit or other recor'nto perform desired opera-

LOCKING
COLLAR...
Draws
the
20. CHUCK
chuck onto the spindle nose. It prevents the
chuck from coming loose during operatiorl.
ALWAYS have the collar tightened.
21. FEED STOP ROD...
Holds stop nuts for dri t l*
ing to specific depths.

22. STOP NUTS...
Limits the downward
movement of the quill at any desired point with _ n
its travel, and prevents the pointer from moving upward.

10. BASE .o.Supports
Drill Press. For additional
stability, holes are provided in base to bolt
Drill Press to floor. (See "Additional
Safety
Instructions
for Drill Presses").
11. COLUMN
SUPPORT,..Supports
guides rack, and provides mounting
column to base.

beyond table
and aligning the table.

23. DEPTH POINTER.,.
Indicates drilling
and is located between stop nuts.

column,
holes for

24. DEPTH SCALE,,.
drilled,

Shows depth of hole beir_ _

25. SPRING CAP.,,
Provides
quill spring tension.

12. COLUMN ... Connects head, table, and base
on a one-piece tube for easy alignment
and
movement.

depth

means

to adju,_t

26, LIGHT
"ON.OFF"
SWITCH...Separate
switch to operate light independent
of dr_it
switch. This permits the light to be "or_,,
while making setups,

13. BEVEL SCALE ... Shows degree table is tilted for bevel operations.
Scale is mounted on
side of arm.
13

getting
27,

to know your drill press

DRILL

"ON.OFF"
SWITCH...
Has locking
THIS FEATURE
IS INTENDED TO
PREVENT UNAUTHORIZED
AND POSSIBLE
HAZARDOUS
USE BY CHILDREN
AND
KEY

insert KEY into switch.
NOTE: Key is made of yellow plastic.

To turn drill ON..
Insert finger under switch

To turn drill OFF..

lever and pull.

Push lever m.

In an emergency;..,the
drill
bit BINDS...
STALLS...
STOPS...
or tends to tear the workpiece loose..,
you can QUICKLY turn the drill
OFF by hitting the switch with the palm of your
hand.

To lock switch in OFF position..,
hold switch
IN with one hand...
REMOVE key with other
hand.
WARNING:

FOR YOUR OWN SAFETY, ALWAYS

LOCK THE SWITCH "OFF" WHEN DRILL PRESS
IS NOT IN USE... REMOVE KEY AND KEEP IT
IN A SAFE PLACE... ALSO.,.
IN THE EVENT
OF A POWER FAILURE (ALL OF YOUR LIGHTS
GO OUT) OR BLOWN FUSE OR TRIPPED CIRCUIT BREAKER, TURN SWITCH OFF...
LOCK
IT AND REMOVE THE KEY. THiS WILL PREVENT
THE DRILL PRESS FROM STARTING UP AGAIN
WHEN THE POWER COMES BACK ON.

jfJ

CHUCK KEY...
It is a self-ejecting
chuck key
which wil! "pop" out of the chuck when you let
go of it. This action is designed to preclude
throwing of the chuck key from the chuck when
power is turned "ON". Do not use any other key
as a substitute, order a new one if damaged or
lost.
BELT TENSION...
Tensioning Belt"_

Refer to section

"Assembly

DRILLING SPEED...
Can be changed by placing
the belt in any of the STEPS (grooves) in the pulleys. See Spindle Speed chart on right side of
Head.
To determine the approximate
dilling
speed,
refer to the table on the LEFT side of the drill
press head.

3116" ROD
OR DRILL

REMOVING
THECHUCK

LOCKING

Insert a piece of 1/4 in. dia. steel rod in one
of the holes in the chuck body.

Insert 3/16 in. dia. rod or drill into one of the
holes in the collar..,
turn it in the direction
of arrow until LOOSE. Continue
to turn it
until the chuck is released.

CHUCK
SLEEVE

CHUCK
BODY

//
114" ROD
OR DRILL

/
\

DRILLING TO DEPTH
To drill a BLIND hole (not all the way through)
a given depth, can be done two ways.

Mark the depth of the hole on the side of the
workpiece.

With the switch
OFF bring the drill down
until the TIP or lips are even with the Mark.

Spin the lower nut down to contact
stop lug on the Head.

Move the POINTER all the way down.

Spin the upper nut down and tighten
the pointer.

the depth

against

;ALE

UPPER

ANOTHER

WAY --

With the switch
OFF, bring the drill down
until the TIP touches the TOP of the WORKPIECE.

Adjust the nuts so the Pointer is set to the
desired DEPTH...
TIGHTEN the UPPER NUT
against the Pointer. For example..,
if you
want to drill a hole one inch deep, set the
pointer at the one inch mark in the scale,

POINTER
LOWER
TIPTOUCHES
WORKPIECE

STOP

NUT

basic drill press operation
"off" immediately, to make sure that the cutting tool is centered in the chuck propeMy
and that the cutting
tool is not causincj
excessive vibration.

Follow the following
instructions
for operating
your drill press to get the best results and to
minimize the likelihood of personal injury.
WARNING: FOR YOUR OWN SAFETY, ALWAYS
OBSERVE THE FOLLOWING SAFETY PRECAUTIONS.
1.
2.

Check spindle speed.
Before operating, turn the switch

"on",

then

Never perform any operation freehand (handholding workpiece
rather than supporting
it
on table) except when polishing.
Keep your hands clear of the cutting

tool.

basic drill press operation
INSTALLING

CHUCK

DRILLS

KEY

Insert drill into chuck far enough to obtain maximum GRIPPING o{ the CHUCK JAWS...the
jaws are approx. 1 in. long. When using a small
drill do not insert it so far that the jaws touch the
flutes (spiral grooves) of the drill.
make sure that the drill is CENTERED in the
chuck before tightening the chuck with the key.
Tighten the drill sufficiently,
SLiP while drilling.
POSITIONING

so that it does not

TABLE AND WORKPIECE

Lock the table to the column in a position so
that the tip of the drill is just a little above the
top of the workpiece.
Always place a piece of BACK-UP MATERIAL
(wood, plywood...
) on the table underneath the
workpiece.
This will prevent
"splintering"
or
making a heavy burr on the underside of the
workpiece as the drill breaks through. The backup material must contact
the left side of the
column.
CAUTION: To prevent the workpiece or the back.
up material from being torn from your hand
while drilling, position them against the left side
of the column. Failure to do this could result in
personal injury.
CAUTION:
If the workpiece
or the back-up
material are not long enough to reach the column, CLAMP them to the table, Failure to do this
could
result
!ni personal
injury.,
i
i
i

n, nl

/
WORKPIECE

WORKP,
ECE
For small pieces that cannot be clamped to the
tabte, use a drill press vise (Optional accessory).
The vise must be clamped or bolted to the table.

TILTING TABLE
To use the table in a bevel (tilted) position, loosen the set screw under table bevel lock with set
screw wrench. Loosen bevel lock with adjustable
wrench.
Titt table to desired angle by reading bevel scale.
Retighten bevel lock and set screw.

BACK*UP
MATERIAL

When drilling
with the table tilted,
ALWAYS
CLAMP WORKPIECE AND BACK-UP MATERIAL
SECURELY TO TABLE before operating
Drill
Press.

Before turning the switch
ON, bring the dr
down to the workpiece
lining
it up with the ho
location.

To return table to original position:
!oosen set
screw and bevel lock, tilt table back to 0 ° on
bevel scale, and retighten set screw - then tighten bevel lock.

FEEDING

Putt down on the feed
effort to allow the drill

handles
to cut.

with only enough

Feeding TOO SLOWLY
might
cause the drill to
burn...
Feeding TOO
_APIDLY
might stop the
motor..,
cause the belt
or drill to SLIP...
tear
the workpiece LOOSE or BREAK the drill bit.

HOLE LOCATION
Make a DENT in the workpiece
where you want
the hole..,
using a CENTER PUNCH or a SHARP
NAIL.

adjustments
WARNING:
FOR YOUR OWN SAFETY TURN
SWITCH "OFF"
AND REMOVE
PLUG FROM
POWER SOURCE OUTLET BEFORE
MAKING
ANY ADJUSTMENTS.
NOTCH

QUILL RETURN SPR_NG
,

BOSS

Move the stop nuts and depth pointer to lowest position and lock in place with wrench to
prevent
quill
dropping
while
tensioning
spring.

Lower table for additional

clearance.

Work from left side of Drill Press.

NOTCH

JAM

Place screwdriver
in lower front notch of
spring cap, and hold it in place while loosening and removing jam [outer] nut only.

NUT

(OUT'ER)
STANDARD
NUT
(INNER)

With screwdriver remaining
in notch, loosen
large standard [inner] nut (approximately
118")
until notch disengages from boss on head.
Carefully turn screwdriver
and engage next notch
REMOVE SCREWDRIVER.

counter clockwise
in boss. DO NOT

10. Proper tension is achieved
gently to full up POSition
3/4" depth.

Tighten
standard
nut with
wrench
only
enough to engage boss. Do not overtighten
as this will restrict quill movement.

Move stop nuts and depth pointer to upper
most position and check tension
while turning feed handles.

11. When there is enough

If there is not enough tension
on spring,
repeat steps 4-8 moving only ONE notch each
time and checking tension after EACH repetition.

12. Check quill while feeding
unrestricted
movement.
tight, SLIGHTLY
loosen
stricted.

replace jam nut and
BUT do not overtighten

when quill returns
when released from

tension after checking,
tighten
to standard nut,
against standard nut.
to have smooth and
If movement
is too
jam nut until unre-

maintenance
WARNING:, FOR YOUR OWN SAFETY, TURN
SWITCH
OFF
AND REMOVE PLUG FROM
POWER SOURCE OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR DRILL PRESS.
Frequently blow out any dust that may accumulate inside the motor.
A coat of automobile-type
wax applied to the
table and column will help to keep the surfaces
clean.
If the power cord _s worn or cut, or damaged
any way, have it replaced immediately.

lubrication
All of the BALL BEARINGS are packed with
grease at the factory. They require no further
l ubricat ion.
Periodically
lubricate the gear and rack table
elevation mechanism, the SPLINES (grooves} in
the spindle, and the RACK (teeth on the quill).
See "Getting to Know Your Drill Press" - p. 12
for diagram.

recommended

accessories

Drill Bits ...........................
See
Rotary Planer ............................
Hold-Down and Guide ....................
E)rill Press Vises ....................
See
Rotary Table .............................
Drill Press Mortising Kit .................
Circle Cutter 1/4-, 1/2- Shank ......
9-3645
Hole Saws up to 21/2 in. dia. max ..... See

Catalog
9-2745
9-2457
Catalog
9-2495
9-29503
- 9-3640
Catalog

5 Pc. Stop Collar Set ...................
Sanding Drums ...................
9-2497
Buffing Wheels up to 4 in. dia. max.. See
Polishing Wheel. 11/2" x 1 In .............
Power Tool Know-how Handbooks
Radial Saw ............................
Table Saw .............................

The recommended
accessories listed here are
current
and were available
at the time this
manual was printed.

9-67063
- 9-2498
Catalog
9-64991
9-2917
9-2918

trouble shooting
WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF"
POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING.

AND ALWAYS

REMOVE PLUG FROM

® CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN.

TROUBLE

PROBABLE CAUSE

Noisy Operation

1. Incorrect

REMEDY

belt tension.

1. Adjust tension. See section
"ASSEMBLY - TENSIONING

2. Dry Spindle.

3. Loose spindle

Drill Burns.

Drill leads off ...
hole not round.

2. Lubricate
section.
pulley.

spindle.

BELT."

See "Lubrication"

3. Check tightness of retaining nut on
pulley, and tighten if necessary.

4. Loose motor pulley.

4. Tighten

1. Incorrect

t. Change speed. See section "Getting
To Know Your Drill Press"...
DRILLING SPEED.

speed.

setscrews

in pulleys.

2. Chips not coming out
of hole.

2_ Retract drill frequently

3. Dull Drill.

3. Resharpen drill.

4. Feeding too slow.

4. Feed fast enough..,

5. Not lubricated.

5. Lubricate drill. See "Basic
Operation" section.

1. Resharpen

Hard grain in wood or
lengths of cutting
lips and/or angles
not equal.

to clear chips.

allow drill to cut.
Drill Press

drill correctly.

Wood splinters on
underside.

1. No "back-up material"
under workpiece.

1. Use "back-up material"...
See Basic
Drill Press Operation" section.

Workpiece torn
loose from hand.

1. Not supported or
clamped properly.

1. Support workpiece or clamp it...See
"Basic Drill Press Operation" section.

Drill Binds in
workpiece.

1. Workpiece pinching drill
or excessive feed pressure.

1. Support workpiece or clamp it...
See
"Basic Drill Press Operation" section.

2. Improper

2. Adjust tension.,.
See section
"ASSEM BLY - TENSIONING BELT".

Excessive drill
runout or wobble.

belt tension.

1. Bent drill.
2. Worn spindle

1. Use a straight
bearings.

2. Replace bearings.
3. Install drill properly...
Drill Press Operation"

3. Drill not properly
installed in chuck.

Quill Returns
too slow or too fast.

drill.

4. Chuck not properly

installed.

1. Spring has improper

tension.

See "Basic
section.

4. Install chuck properly..,
refer to
"Unpacking and Assembly Instructions...
INSTALLING THE CHUCK".
1. Adjust spring tension...
See section
"Adjustments
- Quill Return Spring".

39 38

•Any attempt to repair this motor may create a HAZARD unless repatr is done by a
qualified service technician. Repair service is available at your nearest Sea.rs Store,
20

PARTS

LIST FOR CRAFTSMAN

Key
No.

Part
No.

STD 303240
60522
60510
STD 315225
71363
71364
STD 502503
71406
71315
71399
STD 512505
_05517
STD 551131
71404
71379
71346
STD 551150
!120238
71344
STD 541031
STD 551031
STD 523107
71380
60514
71319
71369

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

15" DRILL PRESS
Key
No.

Description

*Belt "V" 3t8X24
Ring, Retaining
Ring, Retaining
*Bearing, Ball 15MM
Pulley, Center
Pulley, Motor
*Screw, Soc. Set 1t4-20X3/8
*Belt "V" 3/8X27
Pivot Asm.
Knob
*Screw Pan Hd. 114-20x112
Screw, Pan Hd. 5/16-18Xl12
*Lockwasher 5/16
Guard
Support, Motor Bracket
Mount, Motor
* Lockwasher 1/2
*Nut, Hex 1t2-13
®Motor 1/2 H.P.
*Nut, Hex 5116-18
*Washer 5116X1/2X1132
*Screw, Hex Hd. 5/16-18X3/4
Support Motor Bracket
Ring, Retaining
Clamp, Bolt
Shaft, Lever

PARTS LIST FOR CRAFTSMAN

27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
----

I31!

Standard Hardware

item -- May be Purchased

Part
No.

Locally.
21

NO. 113.213850

Description

71368
Rod
71340
Knob
STD 503705 *Screw, Soc. Set 3!8-16Xl!2
71370
Shaft, Asm. Pinion
71367
Rod, Handle
Knob
71339
71338
Key, Chuck
60520
Screw, Slotted Set
Flat Pt. 318-16
STD 541O37 *Nut, Hex 3t8-16
71375
Spring, Torsion
71317
Cap, Spring
STD 541150 *Nut, Hex 1/2-20
STD 541350 *Nut, Hex Jam 1/2-20
71334
Head
60508
Pin, Taper
7! 342
Lever, Adjusting
60515
Ring, Retaining
STD 315255 *Bearing, Ball 25MM
71372
Spacer, Bearing
71337
Insert, Pulley
71357
Pulley, Spindle
71347
Nut, Ring
71389
Bag Of Loose Parts (Not illus.
71388
Box Of Loose Parts (Not Illus.
71329
Owners Manual (Not Ilius.)

15" DRILL PRESS

MODEL

Key
No.

Part
No.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

STD 510807
71269
71371
STD 511103
63418
71393
71356
71326
STD 511105
133423
803709
62442
71397
60256
71341
STD 511002
STD 551210
71323
STD 510803

NO. 113.213850
Description

*Screw, Pan Hd. 8-32X3t4
Bracket, Bulb
Socket, Bulb
*Screw, Pan Hd. 10-32x318
Clamp, Cord
Cord, Motor
Plate, Switch Mtg.
Cover, Switch Plate
*Screw, Pan Hd. 10-32xl/2
Screw, Flat Hd. 6-32X3/8
Connector, Wire
Switch, Locking
Switch
Key, Switch
Lead, Jumper Black
* Screw, Pan Hd. 10-24Xlt4
*Lockwasher,
Ext. #10
Cord W/Plug
*Screw Pan Hd. 8-32X318

repair pa ts
PARTS LIST FOR CRAFTSMAN
.....

DRILL

PRESS MODEL

NO. 113.213850

Key
No,

Part
No.

1
2
3
4
5
6
7
8
9
10
11
12
13
14

71385
71320
STD 502503
71392
71365
71314
STD 551137
STD 523715
71243
71259
STD 741006
71327
71378
71354

Key
No.

Description
Tube, Column
Collar, Rack
*Screw, Soc. Set 114-20X318
Handle Asm. Table Support
Rack
Base
* Lockwasher 3/8
*Bolt, Hex Hd. 3/8-16X11/2
Bolt, Handle
Handle, Sleeve
*Nut Hex M6X1
Crank
Support, Table
Pin, Gear

15
16
17
18
19
20
21
22
23
24
25
26
27

Part
No.

Description

71373
Spacer
71332
Gear, Helical
71386
Worm, Elevation
114507
Nut, Hex 5t8-11
STD 551062 *Washer, 5/8X13/4X5132
71376
Stud, Arm Mtg.
71264
Indicator, Table
STD 511103 *Screw, Pan Hd. 10-32x3/8
71312
Arm, Table
71381
Table
37787
Wrench, He× "L" 5/32
60096
Wrench, Hex "L" 3t16
71303
Handle Asm. Table Lock

PARTS

LiST FOR CRAFTSMAN

15" DRILL PRESS MODEL

NO, 113.213850

!
13

FiG. 1

Key
No.

Part
No.

1
2
3
4
5
6
7
8
9
10
1t
12
13
14
15

60509
STD315235
71384
60503
STD315255
71374
71318
STD 541150
STD 522512
71321
STD 541025
71331
STD 541350
71366
71263

Standarcl Hardware item

Description

Ring, Retaining 21132
*Bearing, Ball 17MM
Tube, Quill
Bearing, Thrust
*Bearing, Ball 25MM
Spindle
Chuck
*Nut, Hex 1/2-20
*Screw, Hex Hd. 1t4-20X1-114
Collar, Stop
*Nut, Hex 1/4-20
Gasket, Quill
*Nut, Hex Jam I/2-20
Rod, Hex Stop
Indicator, Depth

May be Purchased

Locally.
23

iiii.,.i..
_

Sears

MOTORIZED

15 INCH
FLOOR MODEL
DRILL PRESS

owners

manuel
SERVnCE

Now that you have purchased your 15 inch drill press should
a need ever exist for repair parts or service, simply contact
any Sears Service Center and most Sears, Roebuck and Co.
stores. Be sure to provide all pertinent facts when you call or
visit.

The model number of your 15 inch drill press will be found on
a plate attached to the rear of the head.
DRILL PRESS WITH
112 HP MOTOR

HOW TO ORDER
REPAIR PARTS

WHEN ORDERING
REPAIR
FOLLOWING INFORMATION:

PARTS,

ALWAYS

GIVE

THE

PART NUMBER

PART DESCRIPTION

MODEL NUMBER
113.213850

NAME OF iTEM
MOTORIZED 15 INCH
FLOOR MODEL DRILL PRESS

All parts listed may be ordered from any Sears Service Center
and most Sears stores. If the parts you need are not stocked
locally, your order will be electronically
transmitted
to a
Sears Repair Parts Distribution
Center for handling.

_J
Sold by SEARS,
Part No. 71329

ROEBUCK

AND

CO., Chicago,

Form No. SP4738

IL. 60684 U.S.A.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Mon Jul 21 00:09:20 2008
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 113213850 User Manual 15 INCH DRILL PRESS Manuals And Guides L0803156

CRAFTSMAN Drill Press Manual L0803156 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation