Craftsman 11323801 User Manual 12 INCH WOOD TURNING LATHE Manuals And Guides L0711468

CRAFTSMAN Lathe Manual L0711468 CRAFTSMAN Lathe Owner's Manual, CRAFTSMAN Lathe installation guides

User Manual: Craftsman 11323801 11323801 CRAFTSMAN CRAFTSMAN 12-INCH WOOD TURNING LATHE - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN 12-INCH WOOD TURNING LATHE #11323801. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN 12-INCH WOOD TURNING LATHE Manual

Open the PDF directly: View PDF .
Page Count: 24

MODEL NO.

113.23801

LATHE ONLY

MODEL NO.

113.238160

AND

113.238180

LATHE WITH MOTOR

Serial

Number

Model and serial

number may be found

under belt guard.

You should record both

model and serial number

in a safe place for

future use.

CAUTION:

Read GENERAL and

ADDITIONAL SAFETY

INSTRUCTIONS

carefully

CRRFTSMRH®

12-/NCH

WOOD-TURNING LA THE

®assembly

=operating

,repair parts

Sold by SEARS, ROEBUCK AND CO., Chica_o, IL. 60684 U,S,,_._

, L L

FULL ONE YEAR WARRANTY ON CRAFTSMAN WOOD LATHE

"_:_|f within one year from the date of purchase, this Craftsman Wood Lathe fails due to a defect in material or

workmanship, Seers will repair it, free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR

SERVICE CENTER THROUGHOUT THE UNITED STATES.

This warranty givesyou specific legal rights, and you may alsohave other rightswhich vary from state to state.

SEARS, ROEBUCK AND CO. Sears Tower, BSC 41-3. Chicago, IL 60684

general safety instructions for power tooms

1. KNOW YOUR LATHE 13. SECURE WORKPIECE

Read the owner's manual carefu!ly. Learn its application

and limitations as well as its specific potential hazards.

2.,GROUND THE LATHE

This Lathe is equipped with an approved 3_conductor

cordand a 3-prong grounding type plug to fit the proper

grounding type receptacle, The green conductor in the

cord is the grounding wire. Never connect the green wire

to alive terminal.

3, KEEP GUARDS IN PLACE

- in working order, and in proper adjustment and align-

men_.

4. REMOVE ADJUSTING KEYS AND WRENCHES

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents, Floor must

not be sl_ppewdue to wax Or sawdust.

6_ AVOIDDANGEROUS ENVIRONMENT

14,

15,

Mount workpiece securely between centers

DON'T OVERR EACH

Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest perform-

ance, Follow instructions for lubricating and changing

accessories.

16. DISCONNECT YOUR LATHE

before servicing; when changing accessories or attach-

ments,

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging

in.

18. USE RECOMM ENDED ACCESSORIES

Consult this owner's manual for recommended accessories,

Follow the instructions that accompany the accessories.

Don't Qse power" tools it_ damp Or wet locations Or expose

them tO rain. Keep _ork area we/{: lightedi Provide ade- The use of improper accessor es may cause hazards.

quate surrounding wofkspace: _ 19 NEVER STAND ON LATHE

7, KEEP CHILDREN AWAY : : Se_'i0us injury col,ld occur if the Lathe tips over.

All visitors should be kept a safe distance from work area ....

8, MAKE WORKSHOP KID,PROOF Do not store mater als such that il is necessary to stand

on. the tool to reach them,

- with padlocks, master switches, or ay removing starter

keys. 20. CHECK DAMAGED PARTS

9. USE PROPER SPEED Before further use of the Lathe, a guard or other part that

is damaged should be carefu3}V checked to ensure that it

The Lathe win do the job better and safer when Operated

at the proper speed, will operate properly and perform its intended function.

10, USE RIGHT TOOL

Don't force tool or attachment to do a job for which it

was no_ designed.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves, neckties or jewetry

(rings; wristwatchest to get caught in moving parts.

NONSLIP footwear is recommended. Wear orotective

hair covering to contain long hair. Roll long sleeves

aoove the elbow.

1Z USE SAFETY GOGGLES (Head Protection)

Wear safety goggles (must comply with ANSI Z87.1) at all

times. Everyday eyeglasses only have im pact resistant len-

ses, they are NOT safety glasses. Also, use face or dust

mask if cutting operation is dusty, and ear protectors

(plugs or muffs) durin_ extended periods of operation.

Check for alignment of moving parts, binding.of moving

parts, breakage of parts, mounting, ann any other con-

ditions that may affect its operation, A guard or other

par1 that Is damaged should [_e properly repaired or

replaced.

21. DIRECTION OF FEED

Apply cutting too{ [o the workpiece against the direction

of spind{e rotation.

22. NEVER LEAVE LATHE RUNNING

ATTENDED

Turn power "OF F". Don't leave Lathe untd it comes to a_

comp',ete stoP.

addifiona safety instructions

Safety is a combination of operator common sense and

alertness at all times when the Lathe is being used.

WARNING: FOR YOUR OWN SAFETY, DO 7.

NOT ATTEMPT TO OPERATE YOUR LATHE

UNTIL IT IS COMPLETELY ASSEMBLED AND

INSTALLED ACCORDING TO THE INSTRUC-

TIONS . , , AND UNTIL YOU HAVE READ 8.

AND UNDERSTAND THE FOLLOWING:

PAGE

1. General Safety Instructions .................. 2

2, Getting to Know Your Lathe .............. 13

3. Basic Lathe Operation ................... 15

4. Maintenance ......................... 19

5. The Lathe and motor must be bolted down to astand

or workbench for stability.

6. Protection: Eyes, Hands, Face, Ears, Body

a. Wear safety goggles that comply "with ANSI Z87.!

1968, and a face shield if operation is dusty. Wear

ear plugs or muffs during extended periods of

operation.

b. When turning between centers or on the faceplate,

always rough-out "out of round" workpieces at

slow speed. Running the Lathe too fast, so that it

vibrates, could cause the workpiece to be thrown

from the Lathe , . . or the turning toot to be jerked

from your hands.

c. Always revolve the workpiece by hand before turn-

_ng on the motor. If the workpiece strikes the tool

rest, it could split and be thrown out of the Lathe.

d. Do not allow the turning tool to "'bite" into the

workpiece which could result in splitting of the

workpieee or the workpiece being thrown from the

Lathe. Always position the tool rest above the

centedine of the Lathe for spindle turning. Do not

apply the turning tool to the workpiece below the

Ievet of the tool rest,

10.

11.

e, Do not run the Lathe in the wrong direction. This

could cause the turning tool to be thrown from

your hands. The Lathe must run in a direction so

that the workpiece turns toward you.

f. Before attaching aworkpiece to the faceptate al-

ways "rough it out" to as "true round" as possible.

This wilt minimize vibration while turning,

Always fasten the workplece securely to the face

plate.

Failure to perform these set*up operations could

cause the workpiece to be thrown from the Lathe.

g. Avoid awkward hand positions, where a sudden

slip could cause a hand to move into the workpiece.

h, Remove all loose knots before installing workpiece

between centers or on the faeep!ate.

i. Never leave the Lathe work area with the power on

before the Lathe has come to a complete stop, or

without removing and storing the switch key.

12,

13.

14.

15.

[or wood turning lathes

j. Never operate the Lathe with protective cover or}

the unused shaft end of the motor removed.

Hang your turning tools on the wall toward the tail-

stock end of the Lathe. Do not lay them on the bench

so that you must reach over the revolving workpiece

to select them.

Keep firm hold and control of the turning tool at all

times. Special caution must be exercised when knots or

voids are exposed to the turning tool.

Note the following DANGER label which appears on

the front of the belt guard.

DANGER

FOR YOUR OWN SAFETY:

READ AND UNDERSTAND THE OWNER'S

MANUAL BEFORE OPERATING MACHINE:

1. WEAR SAFETY GOGGLES PER ANSI Z87.1

AND FACE SHIELD IF OPERATION IS

DUSTY,

2, DO NOT WEAR GLOVES, NECKTIES, OR

LOOSE CLOTHING. TIE BACK LONG HAIR.

3. BE POSITIVE ALL LOCKS ARE TIGHT BE-

FORE OPERATING MACHINE.

4. TURN WORKPIECE BY HAND BEFORE

APPLYING POWER TO DETERMINE IF IT

CLEARS THE TOOL REST OR OTHER MA-

CHINE PARTS:

5. ROUGH OUT FACEPLATE WORKPIECES

BEFORE INSTALLING ON FACEPLATE TO

AVOID EXCESSIVE VIBRATION AND POS-

SIBLE INJURY.

6. DO NOT MOUNT SPLIT OR CHECKED

WORKPIECE OR ONE CONTAINING KNOT.

7. ALWAYS USE LOWEST SPEED WHEN

STARTING A NEW WORKPIECE, USING

FACEPLATE OR TURNING BETWEEN CEN-

TERS, TO MINIMIZE POTENTIAL INJURY.

Think Safety.

Complete hand sanding of between*centers or facepbte

mounted workpieces BEFORE removing f_om the

lathe. Do not exceed the speed used for the last cutting

operation performed on the workpiece, in accordance

with the speed chart.

NEVER attempt to remount a faceplate turning to

the faeep!ate for any reason. NEVER attempt to

remount a between-centers turning if the original

centers in the turning have been altered or removed,

BE POSITIVE the lathe is set at the lowest speed if

remounting a between centers turning with nomaItered

or;ginal centers.

Use extra caution Jn mounting a between-centers or

spindle turning to the faceptate, or a faceplate turning

to between-centers, for subsequent operations. BE

POSITIVE the lathe is set at the lowest speed before

turning ON,

NEVER mount a workpiece that conta;ns any sp!its,

checks, or loose knots to a facepiate or between

centers.

Do not perform any ope_atioo when hand hoid]n9 the

wo_kpiece. Do not mount a ream,:!,_ o_ a d_ill bt *o t!w-

headstock spindb.

additional safety instructions for wood turning mathes

WARNING': DO :NOT: ALLOW FAMILIARITY WARNING: THE FOUR STEP LATHE AND

(GAINED FROM FREQUENT USE OF YOUR MOTOR PULLEYS FURNISHED ARE DE-

MACHINE) TO BECOME COMMONPLACE, SIGNED TO RUN THE LATHE AT THE COR-

ALWAYS REMEMBER THAT A CARELESS RECT SPEEDS WHEN USED WITH A 1725

FRACTION OF A SECOND IS SUFFICIENT TO R P.M. MOTOR. DO NOT USE A 3450 R.P.M.

INFLICT SEVERE INJURY. MOTOR TO INCREASE THE SPEED BECAUSE

IT COULD BE DANGEROUS.

WEAR YOUR

The operation of an,/ power tool can result n foreign

objects being thrown into the eyes, which can result in

severe eve damage. Alway_ wear safety goggles complying

with ANSI Z87.1 (shown on Package} before commencing

power toot operation. Safety Goggles are available at Sears

retail or cat_ og stores.

motor specifications and electrican requirements

This Lathe is designed to use a 1725 RPM motor only. Do

not use any motor that runs faster than 1725 RPM. tt is

wired for operation on 1tO_120 volts, 60 Hz., alternating

current. IT MUST NOT BE CONVERTED TO OPERATE

ON 230 VOLTS. EVEN THOUGH SOME OF THE RE-

COMMENDED MOTORS ARE DUAL VOLTAGE.

THESE MOTORS HAVE BEEN FOUND TO BE

ACCEPTABLE FOR USE ON THIS TOOL.

HP RPM VOLTS CATALOG NO.

1/3 1725 110-120 1250

1/2 1725 1t0-120 1278

1/2 1725 110-120 1279

CAUTION: Do not use blower or washing machine motors

or any motor with an automatic reset overload protector

as their use may be hazardous.

CONNECTING TO POWER SOURCE OUTLET

This machine must be grounded whi}e in use to protect the

operator from electric shock,

Plug power cord into a 110-120V properly grounded type

outlet protected by a 15-amp, time delay or Circuit-Saver

fuse or circuit breaker.

If you ar_ not sure that your outlet is properly grounded,

have it checked by a qualified electrician.

WARNING: DO NOT PERMIT FINGERS TO TOUCH

THE TERMINALS OF PLUGS WHEN INSTALLING OR

REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK, PARTICULARLY WHEN

USED IN DAMP LOCATIONS IN PROXIMITY TO

PLUMBING. IF AN ELECTRICAL SHOCK OCCURS

THERE fS THE POTENTIAL OF A SECONDARY HAZ-

ARD SUCH AS YOUR HANDS CONTACTING THE

CUTTING TOOL.

if power cord is worn or cut, or damaged in any way,

have it replaced immediately.

if yOur unit is for use on fess than 150 volts it has a plug

that looks like below.

PROPERLY

GROUNDED

OUTLET-,_ i @

3-PRONG

PLUG

GROUNDING

PRONG

This power too! is equipped with a 3-conductor cord and

grounding type plug which has a grounding prong, approved

by Underwriters' Laboratories, The ground conductor has

a green jacket and is attached to the tool housing at one

end and to the ground prong in the attachment plug at the

other end,

This plug requires a mating 3-conductor grounded type

outlet as shown.

tf the outlet you are planning to use for this power tool is

of the two prong type DO NOT REMOVE OR ALTER

THE GROUNDING PRONG 1N ANY MANNER. Use an

adapter as shown and always connect the grounding lug

to known ground.

It is recommended that you have a qualified electrician

replace the TWO prong outiet with a properly grounded

THREE prong outlet.

An adapter as shown below is available for connecting

plugs to 2-prong receptacles. The green grounding tug

extending from the adapter must be connected to a per-

manent ground such as to a properly grounded outlet box.

MAKE SURE THIS IS _GROUNDING LUG

CONNECTED TO A i: Z_"-_,l t

KNOWN GROUND !: (_,_ /ADAPTER

ii e_ ÷ /3--PRONG

'.J "_- _ PLUG

RECEPTACLE /_ ---_

NOTE: The adapter illustrated is for use only if you already

have a properly grounded 2-prong receptacle.

The use of any extension cord will cause some loss of

power. To keep this to a minimum and to prevent over-

heating and motor burn-out, use the table below to deter-

mine the minimum wire size (A.W.G.) extension cord. Use

only 3 wire extension cords which have 3-prong grounding

type plugs and 3-pole receptacJes which accept the tools

p_ug.

Extension Cord Length Wire Size A.W,G.

Upto 100 Ft. 16

100- 200 Ft. 14

200- 400 Ft. 10

CHECK MOTOR ROTATION

WARNING: FOUR YOUR OWN SAFETY, MAKE SURE

PLUG IS NOT CONNECTED TO POWER SOURCE

OUTLET WHEN CHANGING MOTOR ROTATION.

The motor must rotate CLOCKWISE when viewed from

the shaft end to which you will mount the pulley. (See

page 12.) If it does not. change the direction according

to the instructions furnished w_th the motor.

i_:!;_iiii.;_i!il;!::._!_.i;_i!,_'ii-; i :_y:ii:ii:L :/: : : .-::-:: b.._ i¸¸ :

: T ,,tOckram,ook........................ 13

....... :: :: _'!,!.i;;:::; ;i:. 7 Taitstocklock ......... '................. 13

:::;:: on rec0mm#ndea : ;. On - off sw tch .......................... 13

;_:i: _.. :,., . :,... 7 . Spurcenterand cup center (a!igning centers ...... 14

Spu_:an_euPcente_instailation .:..o: :i:. 9: . Ta stock ,, . 14

: Offandon switch:; _.::: i ........ , .:.. ;. 10 SPeed chart ............................ 15

Check motor rotation ............ ,. ;. ; :. , . t2 BASIC LATHE OPERATION .................. 15

GETTING TO KNOW YOUR WOOD LATHE ...._..13

Beitguard lock ..... . ; ....... ; ....... ,.. i, 13

tndex pin ,; ,i,;_i.;;i. ......... ..... .,..13

SpindleJock hole ........................ 13

Tool rest lock .......................... 13

Tool rest base lock ....................... 13

Handwheei ............................. !3

Changing speeds ......................... 15

Spindle turning ......................... 16

Indexing .............................. 18

MAINTENANCE .......................... 19

LUBRICATION ........................... 19

RECOMMENDED ACCESSORIES .............. 21

REPAIR PARTS .......................... 22

-- "TOOLS NEEDED---

3/8- nch wrene I-',-

Screwdriver (medium) _;i

7/1Ginch wrench Framing square !_i

Model 1 t3.23801 Wood Lathe is shipped complete in one

carton (without motor, or bench). The V-Belt anC motor

pulley are furnished.

Model 113.238160 and 1 !3.238180 Wood Lathe is shipped

complete in one carton and includes a Motor.

7Item

[

k___.

Table of Loose Parts Qty.

Motor Pulley ..................... 1

Belt, "Vee" 112x 37 ................ 1

Wood Turning Lathe ............... 1

Owner's Manuaf ................... 1

Belt Guard Assembly ................ 1

Loose Parts Bag _ Part No. 70046

Containing the following:

Wrench. Hex 5/32 ................ 1

Wrench, Hex 3/16 ................ 1

Screw. Type 23 Pan 10-32 x 3/8 ....... 4

Nut, Hex 3/4-16 ................. I

Spur, Center ................... 1

Separate a|l parts from packing materials and check each

one with the "Table of Loose Parts" to make certain alt

items are accounted for. before discarding any packing

material.

tf any parts are missing, do not attempt to assemble the

lathe plug in the power cord or turn the switch on unt}l the

missing parts are obtained and are installed correctly.

Using a 7/1 6" wrench, remove the wood blocks attached to

the Lathe. Save the nuts, bolts and washers, you will need

for _ttaching the Lathe to the bench.

Remove the protective oil that is applied to the bed. Use

any ordinary household type grease and spot remover,

CAUTION: Never use gasoline, naptha or similar

highly volatile solvents. !

Apply a coat of automobile wax to the bed. Wipe all parts

ghty with a clean dry cloth.

Item 1

. I

MOTOR INCLUDED WITH

MODEL 1t3.238160 AND

113.238180 ONLY

Table of Loose Parts Qty.

Cu0, Center .................... 1 !

Point, Center ................... 2

Lockwasher Ext. Tooth No. 10 ....... 4

Key, Switch .................... 1

Clamp Cord .................... 2

Bolt Rd. Hd. Carriage 1/4-20x 1-3/4 ..,4

Washer 17/64 x 47/64 x 1/16 ........ 4

Nut Hex 1/4-20 ................. 4

Screw Pan Hd. Ty. A No. 8 x 1/2 ...... 4

6" Tool Rest ................... 1

Book{el, How To Operate

Your Craftsman Lathe ............. 1

assembly

MOUNTING LATHE AND MOTOR

ON WORKBENCH

1. Drill six 3/8" holes in your bench according to the dia-

gram to the right. NOTE: Make sure the top of your

bench is positioned so that you don't drill into the legs

or rail underneath.

t2"_3'_J

HOLESFO,MOTOR- - 0 - (

r 147/0-(

145/8" i

HOLES FOR LATHE ,-_----.-_ 1

X\ t 63/16"

RONTO B,NO./T

LOCATION OF MOUNTING HOLES

NOTE: To attach your Lathe to the bench, use the bolts,

outs and washer you removed when unpacking.

2. Position Lathe on bench and insert two bolts through

holes in headstock but do not screw on the nuts.

3. Position the Lathe so that the bed is parallel to the front

of the bench. Check the foot, If the bottom of the foot

is not flat on the surface of the bench, loosen the screw

in the foot, tap the screw to loosen the Iocknut inside.

Turn the foot so it is flat on the bench and tighten the

screw.

4. Mark the location on the bench of the hole in foot•

5, Remove the Lathe and ddll a 3/8" hole to attach the

foot,

6, Position the Lathe and insert the bolts from the top.

Pface a fiat washer, a Iockwasher and a nut on the bolts

and tighten the nuts,

Position the motor over the mounting holes. NOTE"

When using aCraftsman double shaft motor, make sure

the 5/8" dia. shaft is to the left when facing the front of

the Lathe• For motors with a !/2" diameter shaft see

Step 15.

NOTE: Motor is included with Model 113,238160 and

113•238180.

NOTE: The ventilation holes in the motor should NOT

face upward as sawdust can collect inside the motor, tf

necessary, loosen the two motor base cFamp screws and

rotate the motor, Then, tighten the clamp screws.

8. Find four 1-3/4" carriage bolts, flat washers and nuts

from among the loose parts (see illustration),

9. Insert the bolts from the top. Place a flat washer aod a

nut on the bolts but do not tighten the nuts at this

time.

1 3/4

BED PARALLEL TO

FRONT EDGE OF BENCH

FOOl

10;Re_n_e the: headstock pu_l!ey using the 5/32" set-

- = scre_Wrench_ _ _:

1-i. Find four pan head thread cutting screws 3/8" long

and four Iockwashers from among the loose parts,

: Attach the belt guard with these screws and Iockwash-

ere, The arrows in this illustration show the location of

the screws.

12. P|ace the headstock pulley onto the headstock shaft as

shown, Position it so that the end of the pulley is ftush

with theend of the lathe spindle.

13, Place the motor pulley on the motor shaft so that the

small diameter is approximately 1/16" away from the

motor.

14. NOTE: When installing the pulley on a 5/8" diameter

motor shaft, make sure that the 3/16" square key

furnished with your motor is in place. Then tighten the

setscrew with a 5/32" setscrew wrench.

i i -¸ i ¸

3/16 x 3/16 KEY

15. NOTE: When installing the pulley on a 112" diameter

motor shaft, make sure that the adapter sleeve and

3/16" square key furnished with your motor are in

place. Then tighten the setscrew with a 5/32" setscrew

wrench.

16, Place the belt on the pulieys and slide the motor

toward the rear of workbench until ait the slack is re-

moved from the belt. NOTE: 1/2 inch deflection of

belt under moderate pressure applied between the two

pulleys is adequate tension, Tighten only two of the

motor mounting bolts using a 7/t6, wrench. J

ADAPTER SLEEVE

1/2 DIA. MOTOR SHAFT

17.Placeastraightedgesuchasapieceo_wood,metalor

framingsquareacrossthepulleysto seeif [heya_ein

linewitheachother,tf theyare,tighte_d_eothe_*.wo

motormountingbolts.If theyarenotinline,toosen

thetwomotorboltsandmovethemotorsideways...

tightenthebolts.

18.Findfourpanheadwoodscrews1/2"tongfromamong

thelooseparts.

Attachthebeltguardplatetothebenchwiththetwo

screws.MakesuretheplateisPARALLELto thebelt.

19.Plugmotorcordintooutletonbackof switchbox.DO

NOTplugmotorcordintopowersourceoutlet.

20.Positionthetwocordsasshownandclampthemto the

tabtewithtwocableclampsand1/2" woodscrews

fromtheloosepartsbag.

21.Coiluptheslackinthecordandtieit withapieceof

tape.

CABLECLAMPS

MOTORCORD

SPUR AND CUP!CENTER INSTALLATION

1. Find a 3/4q6 hex nut among the loose parts and screw

onto head stock spindle until finger tight,

3/4-!6

HEX NUT

2..F_n_twopointsanda spurandcupcenteramongthe

looseparts.To insertpointintocenters,placecenter

between,jawsof a vise. DO not tighten vice. Insert point

into center and wltfr a hammer and nail gently tap

around the base of the point until secure.

Insert spur center into head stock spindle and cup

center into tailstock ram. NOTE: Do not drive or

hammer centers into ,pindle or ram as removal may be

difficulL Use a soft hammer or block of wood and give

them agentle tap.

To remove spur cen_er from spindle, ho_d the spindle

pulley with one hand, and, using a wrench or pair of

ptiers, turn the hex nut counterclockwise until center

isejected.

& To remove cup center insert a 114" wood dowel or brass

rod through the hole in the tailstock ram. Hold the

center with one hand and rap the dowel or rod with a

hammer.

CUP

.TAILSTOCK

RAM

FOOT

WARNING: DON'TCONNECT POWER CORD TO

ELECTRICAL OUTLET IN YOUR SHOP UNTIL

YOU ARE READY TO CHECK MOTOR ROTA-

TION.

ON-OFF SWITCH

The On-Off Switch has a locking feature. THIS FEATURE

IS tNTENDED TO PREVENT UNAUTHORIZED AND

POSSIBLE HAZARDOUS USE BY CHILDREN AND

OTH E RS.

1. Insert key into switch. ,_,.

NOTE: Key is made of yellow plastic.

KEY

[y_LLOVz P_ AST _C

KEY

2. To turn Lathe ON .., _NSERT finger under switch lever

and pull END of switch out.

3. To turn Lathe OFF ... PUSH lever in.

Never leave the Lathe unattended until it has come to a

complete stop and you have removed the switch key.

Do not cycle the motor switch on and off rapidly, as

this may cause the faceplate or sanding disc to !oosen.

In the event this should ever occur, stand clear of the

face plate or sanding disc untit it has come to a complete

stop, .. retighten it.

4. To lock switch in OFF position . HOLD switch IN

with one hand, REMOVE key with other hand.

WARNING: FOR YOUR OWN SAFETY, AL-

WAYS LOCK THE SWITCH "OFF". WHEN

LATHE IS NOT IN USE ,. , REMOVE KEY AND

KEEP IT IN A SAFE PLACE ...ALSO,.. IN

THE EVENT OF A POWER FAILURE (ALL OF

YOUR LIGHTS GO OUT) TURN SWITCH OFF...

LOCK IT AND REMOVE THE KEY. THIS WILL

PREVENT THE LATHE FROM STARTING UP

AGAIN WHEN THE POWER COMES BACK ON.

HOLD

PULL

CHECK MOTOR ROTATION

The Lathe must rotate counterclockwise when viewed from

the spindle end.

NOTE: Make sure the spur center is removed from the

spindle.

1, Plug the Lathe power cord into a properly grounded

oudet (See page 4}.

2. Stand clear of the Lathe spindle and turn the switch ON.

Notice the rotation of the spindle If it is NOT [urning

COUNTERCLOCKWISE . ._ Remove the Lathe power

cord plug from the outlet and change the rotation of

the motor according to the directions furnished with

the motor.

WARNING: FOR YOUR OWN SAFETY, MAKE

SURE PLUG IS NOT CONNECTED TO POWER

SOURCE OUTLET WHEN CHANGING MOTOR

ROTATION,

ROTATION

TERMINAL

COVER

getting to know your wood lathe

SPEED

1NDEX PIN

BELT GUARD

HANDWHEEL

TAILSTOCK /

10 SPUR RAM

CENTER 10 CUP CENTER

SPINDLE

LOCK 7 TAILSTOCK RAM

HOLE

TOOL REST

TOOL REST "_

BASE

BELTGUARD

LOC K

TOOL

BASE

ON-OFF

SWITCH

HEADSTOCK

\BED

11TAILSTOOKFOOT

TAILSTOCK

LOCK

TOOL/REST

LOCK

1. BELT GUARD LOCK ... Locks the hinged part of

the guard during operation.

2. INDEX PIN . ,. Engages with the spindle pulley to

determine equal spacing for cuts for fluting or feeding,

or for dividing face plate work. DO NOT USE FOR

REMOVING FACEPLATES.

3. SPINDLE LOCK HOLE... For removing face-

plates or sanding discs. Insert a setscrew wrench, large

nail or bolt in the hole to hold the spindle while un-

screwing faceplate or sanding disc,

4. TOOL REST LOCK . . .Ciamp the too; rest to the

tool rest base:

5. TOOL REST BASE LOCK .. . Clan_psthe too_

rest base to the bed,

6. HANDWHEEL ... Adiuststhe tailstock ram.

7. TAtLSTOCK RAM LOCK .. . Clamps tfle ram in

the taitstock.

8, TAILSTOCK LOCK, . .Clamps the [aiistock to the

bed.

9. ON-OFF SWITCH ..... Seepage10.

geffing fo know your wood

10. SPUR:CENTER AND CUP CENTER.. •. areused

for spindle turning and should always be in alignment.

ALIGNING CENTERS

If the centers are not in line as shown, make the follow-

ing adjustments.

I. Make sure the tailstock and ram are locked when

checking for aiignment

2. Loosen the screw in the foot . . TAP the screw to

loosen the Focknut inside.

3. Using a 3/16" setscrew wrench, loosen the setscrew

on the back of the headstock. The screw is located

about !-3/4" from the bottom.

4. Swing the taiL_tock so that the two F)oints are in

line . ,.tighten the setscrew in the headstock and the

screw in the end of the tailstock.

3/16" SETSCREW

WRENCH

HEADSTOCK

3/16"

SETSCREW I

V O , '_

FOOT

TAI LSTOCK _

HANDWHEEL

11. TAILSTOCK .... supports the workpiece for spindle

turning.

The taifstook contains a brass screw which Dears against

the "key" on the underside of the bed. This screw pre-

vents excessive "looseness" (rocking back and forth} of

the tailstock.

1, Loosen the tocknut using a 7/16" wrench.

2. Tighten the screw moderately against the key, then

loosen it about t/4 turn.

Slide the tai]stock along the bed. I f it does not stick or

bind in any one spot, tighten the nut. If it binds or sticks,

loosen the screw ordy enough so that the tailstock slides

smoothly al ong the bed.

__i__ii_i:_!i:ii_!!_i_:_i___/_,iiii_:i_i___:_ii_i_i!_/__/,i__!i_,_,__, 14

BRASS

SCREW

LOCKNUT KEY

i ¸

12, SPEED CHART .... Indicates generalrecommended

speeds for various sizes of workpieces.

basic lathe operations

CHANGING SPEEDS

The belt is shown positioned on the second steps from

the outside end of the pulleys. This causes the lathe to

run 2250 R,P.M.

Suppose you wish to run the lathe slower - say, t350

R.P.M. You must shift the belt inward.

1, Make sure the power cord is removed from the outlet.

ROTATE MOTOR

COUNTERCLOCKWISE PULLEY

2, With the belt guard raised, rotate the motor puiley

COUNTERCLOCKWISE with your teft hand while

pushing on the belt with your right hand.

3, Continue to rotate the pulley while pushing on the

belt until it "climbs" down into the third step of the

motor pulley.

4. Nowrotatethe spindle pulley CLOCKWISE with yo_r

right hand while pushing on the belt with your left

hand. The belt will climb up into, the third step of the

spindle pulley.

To make the lathe go faster, the belt must be shifted out-

ward.

1. Rotate the spindle pulley CLOCKWISE with your

right hand. Pul! on the beet whiie rotating the pulley

until it climbs down into the next smaller step.

2. Now rotate the motor pulley COUNTERCLOCKWISE

with yourteft hand while pulling on the belt with your

right hand, The belt will c_imb up into the next larger

step.

BE LT

/'SPINDLE

PULLEY

"b ¸ ,_

asnc lathe operatRons

SPINDLE TURNING.

If you have never done any amount of wooc turning,

we suggest that you practice using the various wood

turning tools. Start with asmatl spindle turning;

Be sure to study the "'Handbook" which you received

with your lathe. !t explains and illustrates the correct

use of the turning toots, the positioning of the tool

restand other information to hefp you gain experience.

1 Select a piece of wood 2" x 2" x 12".

2. Draw diagonal lines on each end to locate the centers

3. On one end, make asaw cut approximately 1/16" deep

on each diagonal line. This is for the spur center,

4. The other end is for the cup center. Place the point of

the cup center on the wood where the diagonal lines

cross DIAGONAL LINES

ON BOTH ENDS

5, Dri#e tt_e cup center into the wood. Use a wooden

; mallet or a plastic hammer. If you don't have one, use

aSleet hamme_, but put a piece of wood on the end of

{h eit.

:&Remove the cup::Center ahd drive the spur center into

life ether end:0f the wood. Make sure the spurs are in

: the :saw cutSl Rem0Ve the spur center

7. Make Su lethe centers and the hole in the spindle and

the tailstock ram are clean. Insert the spur center into

the headstock and the cup center into the tailstock

and tap them in rightly with a piece of wood. Do not

drive them in;

8. Put a drop of Oilor wax on the wood where it con-

tacts the cup center. This will lubricate the wood

Wf_ile it _s turning,

9. Place the wood between the centers and lock the tail-

stock,

I0. Move the cup center into the wood by turning the

hand wl_eel. Make sure that the cup center and spur

center are "seated" into the wood in the holes made

insteps 5 and6 above. Rotate the wood by hand

while tUrning the hand wheel.

: : ....

...... t6

1t. Adjust the tool rest approximately 1/8" away from

the corners of the wood and 1/8'" above the center line.

Note the angted position of the tool rest base.

Lock the tool rest base and the tool rest,

TOOL REST

I/8"

WOOD

Look at the speed chart. Notice that a 2" square

turning up to 18" tong should run at 875 R.P.M. for

"roughing" Move the V-belt on the pulleys to the

slowest speed,

Rotate the wood by hand to make sure that the corners

do not strike the tool rest.

INDEXING

]he spindle pulley contains 36 equalty spaced holes, The

index pin engages with these holes to keep the spindle

from turning white you put amark on the workpiece,

For example: To locate the position of six spokes in a

wheel:

1, Pull the index pin outward and turn it so that the small

cross pin slips into the slot, This wilt allow the index

pin to engage in one of the holes in the pulley and pre-

vent the spindle from turning.

2. Adjust the tool rest approximately at the centerline

and make a mark.

3, Puiioutthe index pin and slowly rotate the workpiece

until _he pin slides into the next h01e in the pulley,

4iD6 1:his six: times andput the next rn a r k on the work-

marks wilt be space d 600 apart. Con-

: t$nue this Operation until six spokes are marked 60 _

aParti :

5. Spindle turnings Can be divided in the same manner.

maintenance

WARNING: FOR YOUR OWN SAFETY, TURN

SWITCH "OFF" AND REMOVE PLUG FROM

POWER SOURCE OUTLET BEFORE MAINTAIN-

ING OR LUBRICATING YOUR LATHE.

Frequently blow out any dust that may accumulate inside

the motor.

A coat of automobile-type wax applied to the bed will help

to keep the surfaces clean and allow the tool rest and taif-

stock to more more freely.

If the power cord is worn or cut, or damaged in any way,

have it replaced immediately.

For motor maintenance, follow instructions furnished with

motor.

WIRING DIAGRAM

t WHITE

MOTOR

BLACI_

CORD

........... I1! i llq-' II!11 -m

nubrication

All of the BALL BEARINGS are packed with grease at the

factory. They require no f'._rther lubrication.

Periodically lubricate the ram in the tailstock with No. 20

or No, 30 engine oil.

For motor lubrication, follow instructions furnished w th

the motor.

:trouble shooting

TROUBLE SHOOTING CHART

., u

TROUBLE

Motor wilt not run.

Lathe slows d own

when turning

Tailstock rocks

back and forth

excessively.

Headstock loose

on bed.

Wood burns at

taiist0ck end.

im,,,,,,,,,,,.................. ,, ..... ,, u,,,,,,,,,,,,,,,,,,,

PROBABLE CAUSE ........................... R EM"EDY

1, Defective On-Off switch. 1. Replace defective parts before using Lathe

Defective sw:itch cord.

Defective sw_tch box receptacle.

2, Motor protector open, 2.

(only if your motor is

equipped with an

overload protector).

Other cause

1. V-belt too loose 1.

1, Brass adjusting screw is too 1.

loose.

1. Setscrew not tight, 1.

f. Cup center too tight or not I.

}ubricated.

again.

Consult Sears Service. Any attempt to repair this

motor may create aHAZARD utlless repair is

done by a qualified service technician. Repair

service is available at your nearest Sears Store.

Adjust belt tension, see Assembly Section.

Adjust screw. See Section, "Getting To Know

Your Lathe".

Tighten setscrew. See Section, "'Getting To

Know Your Lathe".

Back off tailstock ram and lubricate

cup center. See Basic Lathe Operation

Section, "Spindle Turning."

recommended accessories

RECOMMENDED ACCESSOR! ES

ITEM CAT. NO.

Work Bench ............. 9-10266, 9-10278, 9-10271

Motor Pulley (Four Step) I/2"' Bore .......... 9-27921

Moto_ Pulley (Four Step) 5/8" Bore .......... 9-27922

Drill Chuck 1/2" Capacity with

No. 1 M,T. Shank .................... 9-22342

Work Arbor 1/2" D_a. with

No, 1 M.T. Shank .................... 9-21532

Screw Center with No. 1 M,T, Shank ......... 9-21164

Ball Bearing Center with

No. I M.T. Shank .................... 9-21122

60°Center with No. 1 M.T. Shank ........... 9-21102

Face Plate, 4" Dia. with 3/4"

No. t6 Threads 9 holes ................. 9-2489

Face P|ate Including Spurs and Screw Center

3" Dia, with 3/4'" No, 16 Threads ......... 9-20912

Sanding Table ........................ 9-24922

9" Dia. Sanding Disc Only with 3/4"

No. 16 Threads ...................... 9-24906

Turning Toots ................. (SEE CATALOG)

Draw Bolt w_th 1/4" No. 20 Threads ......... 9-21542

Power Tool Know Handbooks

Radial Saw .......................... 9-2917

Table Saw ........................... 9-2918

Bowl Turning Tootrest ................... 9-24903

Face Plate 6" with 3/4"

No. 16 Threads 6 holes ................. 9-24904

Copy Crafter ......................... 9-24907

Speed Reducer ........................ 9-23895

Face Plate 4" dia. with 3/4'"

No. 16 Threads, Cast Iron, 6 holes ......... 9-23865

The above recommended accessories are current and were

available at the time this manual was printed.

repair parts

¢,4

w,,-

%..-

,:.o

(%t

%,.-

¢0

%....

U.I

,.r.

I--

I-

L'N

.£

• uo t-- o o

_00oooooo_o _ ¢oo 0 ,-o P... r.. o ooo

i'-,., m.

_-- p- f-- 1--

_0 09 _ r/)

o _-_

Z:53

Z _-_

o if2

g =

>_0 _._

.s+

_ m

_ oo

'-- o

+ + +o

F-

-_ Z

owners

manual

SERVICE

MODEL NO.

113.23801

LATHE ONLY

MODEL NO.

113.238160

AND

113.238180

LATHE WiTH MOTOR

HOW TO ORDER

REPAIR PARTS

?2-iNCH

WOOD°TURNING LATHE

Now that you have purc'nased your 12" Wood-Turning Lathe

should a need ever exist for repair parts or service, simply

contact any Sears Service Center and most Sears, Roebuck

and Co. stores. Be sure to provide all pertinent facts when you

catl or visit.

The model number of your 12" Wood-Turning Lathe will be

found on a plate under the belt guard.

WHEN ORDERING REPAIR PARTS, ALWAYS

GIVE THE FOLLOWING INFORMATION:

PART NUMBER PART DESCRIPTION

MODEL NUMBER

113.23801

113.238160

113.238180

NAME OF iTEM

12-INCH WOOD

TURNING LATHE

All parts listed may be ordered from any Sears Service Center

and most Sears stores. If the parts you need are not stocked

Iocatty, your order witl be electronically transmitted to a

Sears Repair Parts Distribution Center for handling,

Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.

Part No. 70045 Form No. SP4322-4 Printed in U.S,A. t/81

Craftsman 11323801 User Manual 12 INCH WOOD TURNING LATHE Manuals And Guides L0711468

CRAFTSMAN Lathe Manual L0711468 CRAFTSMAN Lathe Owner's Manual, CRAFTSMAN Lathe installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation