Craftsman 137212140 User Manual MITER SAW Manuals And Guides LR708226

CRAFTSMAN Miter Saw Manual LR708226 CRAFTSMAN Miter Saw Owner's Manual, CRAFTSMAN Miter Saw installation guides

User Manual: Craftsman 137212140 137212140 CRAFTSMAN MITER SAW - Manuals and Guides View the owners manual for your CRAFTSMAN MITER SAW #137212140. Home:Tool Parts:Craftsman Parts:Craftsman MITER SAW Manual

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

Operator's Manual

2.5 HP (Max. Developed)
10" Blade
4800 R.P.M.

COMPOUND MITER SAW

With Laser Trac®
Model 137.212140

CAUTION;

e Safety Instructions

Before using this Miter Saw,
read this manual and follow
all its Safety
Operating

e Installation
• Operation
e Maintenance

Rules and

Instructions

e Pads List

Customer

Neip Line

t=800=843=t682

Sears, Roebuck and Co., Hoffman Estates,. 1L 60179 U.S.A.
Visit our Craftsman website: _w_w, sears.comlcraftsman
Part No.:137212140001

SECTION

PAGE

Warranty ................................................
Product Specifications ...........................
- Power ToolSafety o.............................
Compound Miter Saw Safety .................
Electrical Requirements and Safety .......
Accessories and Attachments ...............
Tools Needed For Assembly ...................
Carton Contents ......................................

i i

iiii, _,,i......

.........ii,

SECTION

2
2
3
4
4-5
6
6
7

PAGE

Know Your Compound Miter Saw ..........
Glossary of Terms
Assembly and Adjustments:; _._.,, .........
Operation ......... _....................................
Maintenance ............................................
Troubleshooting Guide ............................
Parts List,,,...........................................

B
9
10
15
22
23
24

................................

-i i ,:,,ii -

.....

i"':

..............

FULL ONE YEAR WARRANTY
if this tool fails due to a defect in material or workmanship
at !ts opt!on repair or replace it free of charge.

within one year ol date of purchase,

Return this tool to a Sears Service Center for repair, or to place of purchase
This warranty
state to slate,

gives you specific

legal dghts,

Sears, Roebuck
....................

'.....

lUU

for replacement.

and YOU may also have other rights which

an d Co., Dept, 817 WA, Hoffman
i

iiin,llli

Sears will

Estates,

may vary from

IL 60179
..................

1,1,,11,

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
= Lead from lead-based paints
• Crystalline silica from bricks, cement and other masonry products

o Arsenic and chromiumfrom chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work ina well ventilated area and work with approved Safety equipment such as
dust masks that are specially des}gnarl to filter out microscopic
particles.

: MOTOR
i Power source ..........................
Horsep0wer.;.L_.. ......... i,... :;.
Arbor Shaft Size
Speed.; ........_.o..o.;......... .,,,_.
Brake.:.;.;; ..............................
: Double Insulated................
,:;....
MITER SAW
:Cutting Capacity:
: :Crosscut...... ;.,-,, ... .............
:: Miler45 '_R&L .....................
: Bevel 45=L ................. :........
450 Miler and 45" Bevel..............

:
120 V AC; 6OHZIi5 Amp
2,SHP (Max, Devet0ped}
5./B"
....
4800 RPM (No load)
Electric
Yes

Rotating Table;
Diamatero_o,,
::.,. ........................ t2.S/B"
Mtter Detent Stops, ..................... 0, 15, 22o1.,'2,31.6,
....
45= R. & L
Bevei P0sitiveStaps_..:,.,,.:o,.,,,;, 0, 45=
:
Base Dirnensions,.o,i..i.,.;.i=_
....
20-112,x 16..1t4"
Dust Collection........ :L, .;.........
Yes
Exlension Wings.......................
Yes
NetWeight.................................

33 Lbs

2-5/8' X 5-1t2"
2_/8' x 3-1/2"
t-t/2" x 5_1t2=
1-1/2" X3-1/2"

To avoid electrical hazards, fire hazards Or damage to the tool, u_e proper ¢.Ircuit protection.
This to01 is wired at the factory for 110.120 Volt operation. It must be connected to a 110-120 Volt t 15 Ampere time
delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately If It is worn, cut or damaged
In any way.
Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules
could result In serious injury to you or damage to the tool.

GENERAL

SAFETY

INSTRUCTIONS

BEFORE USING THIS POWER TOOL
Safety is a combinatio_ of common sense, staying ale_
and knowing how to use your power tool

To avoid mistakes that could cause sedous injury,do not
plug the tool in until you have read and _mderstood the
following
1. READ and become familiar with the entire Operators
Manual. LEARN the tool's application, limitations and
possible hazards.
2. KEEP GUARDS IN PLACE and in working order,
3. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ONe
4. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5. DON'T USE IN DANGEROUS ENVIRONMENTS.
Don't use power tools in damp locations, or expose
them to rain or snow. Keep work area well lighted.
6. KEEP CHILDREN AWAY. All visilors and bystanders
should be kept a safe distance from work area
7. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches, or by removing starter keys
8. DON'T FORCE THE TOOL. {t wilt do the job better
and safer at the rate for which it was designed.
9. USE THE R1Gt'rr TOOL. Do not force the tool or an
attachment to do a job for which it was not designed,
10,USE PROPER EXTENSION CORDS. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough
to carry the current your product will draw, An
undersized cord will result in a drop in line voltage
and in loss of power which will cause the tool to
overheat. The table on page 5 shows the correct size
to use depending on cord length and nameplate
ampere rating_ If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
11 ,WEAR PROPER APPAREL. Do not wear loose
¢10thihg, gloves, neckties, dngs, bracelets, c r other
jewelry which may get caught in moving parts
Nonslip footwear is recommended Wear Drotective
hair covedng to contain long hair.

12.ALWAYS WEAR EYE PROTECTION. Any power tool
can throw foreign objecl_sinto the eyes and
could cause permanent eye damage.
ALWAYS wear Safety Goggias (not
glasses) that comply with ANSI Safety
standard Z87.t Everyday eyeglasses
have onfy impact -resistance lenses
They ARE NOT safety glasses. Safety Goggles ere
available at Sears, NOTE: Glasses or goggles not in
complianCE with ANS! Z87ol could seriously injure
you wllen they break.
13.WEAR A FACE MASK OR DUST MASK, Sawing
operation produces dust.
14oSECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and it
free_ both hands to operate the tool
15.DISCONNECT TOOLS FROM POWER SOURCE
beIore sewicing, and when changing accessories
sucl_ as blades, bits and cutters,
16.REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in the OFF position
before plugging the tool in,
17,USE RECOMMENDED ACCESSORIES. Consult this
Operators Manual for recommended accessories
The use of improper accessories may cause risk ol
injury to yourself or others
1B_NEVER STAND ON THE TOOL. Serious injury could
occur if ]h_ Iool is tipp@dor il the culling tool is
uninlentfona]ly contacted
19oCHECK FOR DAMAGED PARTS. Before further usa
of the tool, a guard or other part that ]s damaged
should be carefully checked to determine th_t it will
operate properly and perform its intended funclion check for alignment of moving parts, binding of
moving parts, breakage of pans. mounting, and any
other conditions that may affect its operalion A guard
orother part that is damaged should be properly
repaired or replaced
20°NEVER LEAVE THE TOOL RUNNING UNATTEt._DED.
TURN THE POWER "OFF". Don't wa]k away from a
running toot until the blade comes to a complete stop
& unplug Ihe unit
21.DON'T OVERREACH.
balance at all times,

Keep proper ioo_ing and

22.MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for bes[ and safest par[ormanceoFoIIow
instrucUonsfor lubricating and changing accessories.
23,WARNING: Dust g_nerated from certain mater;als
can be hazardous to your heaith, Always opera[e saw
in well-ventilated area ant provide for _roper dust
removal

SPECIFIC SAFETY INSTRUCTIONS
THIS COMPOUND MITER SAW

FOR

18.MAKE SURE the blade is not contacting the
workpiece before the switch is turned ON

19JMPORTANT: After completing the cut, release the
USE ONLY CROSS-CUTTING SAW BLADES. When .......
power switch and wait for the blade to stop before
using carbide tipped blades, make sure they have a
returning the saw to the raised position..
negative hook angle.
2&MAKE SURE the blade has come to a compfete stop
IMPORTANT: DO NOT USE THtN KERF BLADESbefore removing or securing the workpiece, changing
they can deflecl and conlacl guard and can cause
the workpiece angle, or changing the angle of the
possible injury to the operator.
blade.
2. DO NOT operate the miter saw until it is completely
21.NEVER cut metals or masonry products with this tool,
assembled and installed according to these
This miter saw is designed for use on wood and
instructions,
wood-like products,
3. IF YOU ARE NOT thoroughly familiar with the
operation o! miter saws, seek guidance from your
22.NEVER cut small pieces If the workpiece being cut
supervisor instructor, or other qualified person
would cause your hand or fingers to be within 7-t/4"
inches of the saw blade the workpiece is too small
4. ALWAYS held the work firmly against the fence and
table. DO NOT pedorm any operalion free hand (use
?_3.PROVIDE adequate support to the sldes of the saw
clamp wherever possible)
table far long work pieces.
I.

5. KEEP HANDS out of the path ot the saw b]ade, If the
werkpiece you are cutting would cause your hands to
be within 7-1/4" inches of the saw blade, the
workpieca should be ciamped in place before making
the cut.
6. BE SURE the blade is sharp, runs freely, and is free
of vibration
7. ALLOW the motor Io come up to fu_l speed before
starting a cut.
8. KEEP THE MOTOR AIR SLOTS CLEAN and #eeoI
chips or dust,
9. ALWAYS MAKE SURE all handles are tight before
cutting, even if the table is positioned in one of the
positbe stops,,
10,BE SURE both the blade and the collar are clean and
the arbor bolt is tightened securely.

24,NEVER use the miter saw in an area with fiammabb
liq_Jidsor gases
2&NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or other,,4se damage the
material.
26.SHUT OFF the power belore servicing or adjusting
the too].
27,DISCONNECT the saw from the power source and
clean the machine when finished using
28.MAKE SURE the work area is clean before leaving
the machine.
29.SHOULD any pan of your miter saw be missing,
damaged, or fail in any way, or any electrical
component fail te pedorm properly, shut off the switch
and remove the plug from the power supply oullet.
Replace missing, damaged, or falled parts before
resuming operation.

11.USE only blade collars specified for your sew.
12. NEVER use blades Iarger or smaller in diameter
than 10-inches.
13. NEVER apply lubricants tc the blade when it is
running,
14. ALWAYS check the blade for cracks or damage
before operation. Replace a cracked or damaged
blade immediately.

15. NEVER use blades recommendedbr operalional
less than4800 RPM.
16.ALWAYS keep the blade guards in place and use at
all times
17.NEVER reach around the saw blade

POWER SUPPLY AND MOTOR SPECIFICATIONS
The AC motor used _n this saw is a uriiverse[.
nonreversible type. See "MOTOR _ in the "PRODUCT
SPECIFICATIONS" seciion on page 2.
To avoid electrical hazards, fire hazard_ or damage 1o
the tool, use proper ,circuit protection. Your saw is wired
at the factory for 120V operatbn Connect to a 120V, 15
Amp circuit and use a I5 amp, time delay lose or circuit
breaker, To avoid shock or fire, if power cord is worn or
cut, or damaged in any way, have it replaced
immediately.

ELECTRICAL REQUIREMENTS
DOUBLE INSULATED

- cont'd

[]

The power tool is double insulated to provide a double
thickness of insulation beb.veen you and tool,s-electrical
system. All exposed metal parts are isolated from the
internal metal motor components with protecting
insulation,
Replacement parts - When servicing use only identical
replacement parts.
Polarized plugs-This
the one shown below:

saw has a plug that looks like

To reduce the risk of eleclricat shock, this saw has a
polarized plug (one blade is wider than the other] Tllis
plug will fit in a polarized outlet only one way. If |he plug
does not fit fully in the curie! reverse the plug tf it st;tl
does not fit, contact a qualified electrician to install the
proper outlet. DO riot change the plug in any way.

Double insulation does not take the place o! normal
safety precautions when operating this tool
To avoid electrocution:
1. Use only identical replacement parts when servicing a
toolwith double Insulation. Servicing should be
performed by a qualified technician
2, Do not use power tools tn wet or damp locations or
expose them to ra'=nor snow.

MOTOR SAFETY

PROTECTION

IMPORTANT:
To avoid motor damage, the motor sl_outd be blown out
or vacuumed frequently to keep sawdust from intedefing
with the motor ventilation,
t. CONNECT this saw to a 120V, 15 amp. circuit with a
15 amp, time delay fuse or circuit breaker. Using the
wrong size fuse can damage the motor..
2 If the motor won't start, release the tdgger swilch
immediately, UNPLUG "THE SAW, Check the saw
blade t.o make sure it turns freely< If the blade is Iree,
try to sled the saw again. If the motor still does not
start, refer to lhe "TROUBLESHOOTING
GUIDE"
3. If the tool suddenly stalls while cutting wood, release
the tdgger swltch, unplug the tool, and free the blade
from tile wood. The saw may now be started and the
cut flnisha&

4. FUSES may "blow" or circuit breakers may trip
frequently if:
a. MOTOR is overloaded - ovedoading can occur if
you feed too rapidly or make too many startJstops
in a shod time.
b. LINE VOLTAGE is more than 10% above or below
the nameplate voltage rating For heavy loads, the
voltage at motor terminals must equal the voltage
specified on the nameplate.
c,, IMPROPER or dull saw blades are used,
5. Most motor troubles may be traced to loose or
incorrect connections, overload, low voltage or
inadequate power supply widng, Always check the
connections, the load and supply circuit if the motor
doesn't run well. Check minimum gauge for the lenglh
of cord you are using on the chad below,
GUIDELINES FOR EXTENSION CORDS
Use a proper extension cord. Make sure your
exlension cord is in good condition. When using an
ex'lension cord, be sure to use one heavy enough to
carry the current your product will draw, An undersized
cord will cause a drop in line voltage, resulling in loss of
power and cause overheating. The table below shows
the correct size to use depending on cord length and
nameplate ampere rating. II in doubt, use the nexl
heavier gauge The smaller lhe gauge number, the
heavier the cord.
Be sure your extension cord is property wired and in
good condition. Always replace a damaged extension
cord or have it repaired by a qualified person before
using iL Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This
circuit must not be less than # 12 wire and should be
protected with a 15 Amp lime delay fuse. Before
connecting the to01to the power line, make sure the
switch is in the OFF position and the electric current is
raled the same as the current stamped on ti_e motor
nameplate, running at a lower voltage will damage the
motor.

.........

(When using 120 volts only)

Amper_e
i"r,,_ie l_n

Rating
n_l more lhan

Totat lengt_ of cord in feet
25'

5[t'

Ic_3*

t50 +

'14

1i'_"_

n_l re_--'_mm-.nded

CAUTION: In all cases make cedain the receptacle in
question is properly grounded. I{ you are not sure have a
certified electrician, check the receptacle

RECOMMENDED

ACCESSORIES
Phillips

•

Use only sccessories recommended for thismiter
saw. Followinstructions that accompany aocessodes_
Use ot improper accessories may cause hazards
The use el any cutting toot e×cept 10 inch saw
blades thai meet the requirements under
recommended accessories is prohibited. Do not use
accessories such as shaper cutters or dude sets.
Ferrous metal cutting, the use of abrasive wheels
and the cutting of masonry producL_are prohibited
Do not attempt to modify this tool or create
accessories not recommended for use with this tool.
Any such alteration or modification is m}suse and
could result in a hazardous condition leading tO
possibleseriousinjury,

ACCESSORIES
Visit your Sears Hardware Department Orsee [he Sears
Power and Hand Toot Catalog to purchase
recommendedaccessories for this powertool.

To avoid the risk el personal injury, do not modify this
power tool or use accessories not recommended by
Sears.

Read warnings and conditions on your CARBIDE
TIPPED SAW BLADE. Do not operate the saw without
tile proper saw blade guard in place. Carbide is a very
hard but brittle material Care should be taken while
mounting, using, and storing carbide tipped btades to
prevent accidental damage. Slight shocks, such as
striking the tip while handling, can seriously damage the
bladeo Foreign objects in the workpiece, such as wire or
nails, can also cause tipsto crack or break off. Bo!ero
using, always visually examine the blade and tips tor
bent teeth, cracks, breakage, missing or loose t_ps,or
other damage. Do not use if damage is suspected,
Failure to heed safety instructions and warnings can
resull in serious bodily injury.

screwdriver

UNPACKING

YOUR

MITER SAW

'To avoid injury from unexpected sta_ing or electrical shock,
do not plug the power cord into a source of power dur}ng
unpacking and assembly, This cord must remain
unplugged whenever you are adjusting!assembling the
saw,

Remove the miter saw from the Carton. IMPORTANT:
Do not lilt the miter saw by the switch handle or miter
table handle.. It may cause misatignmenL Lift only by
the buill-In carry handle located at the topof the
machine.

2., Place the saw on a secure siafionary work surface.
3. Separate all parts from the packing material. Check
. each one with the illustration below lo make certain aJl
items are accounted for, before discarding any packing
material,

If any parl is missing or damaged, do not atlempt to
assemble the miler saw, or plug in the power cord until the
missing or damaged par_ is correctly replaced, To avoid
electric shock, use only identical replacement pads when
servicing double insulated lools.

/
]

Dust Bag

Extension Wings &
Stop Block

Hold-down Cla_
MilerTable
Handle

Exlension Wing
LockingScrews

Blade Wrench

Lock off button

Upper Blade Guard

Cutting Head Handte
Dust chute
Dust Bag
Lower Blade Guard

Blade

g
Miter Scale

Base
" Positive Stop Locking Lever
i;ler handle

Stop lalch
Pivot boll
Arbor Lock

Bevel Scale
: :

: Fence

Ex-lension Wing Mounting
Hotes

CRAFTSMAN COMPOUND MITER SAW TERMS
ARBOR LOCK - Allows the user to keep the btade lmm
rotating while tightening or loosening the arbor locking
bolt during blade replacement or removal.
BASE - Supports the fable, holds accessories
allows for workbench or leg set mounting

and

BEVEL LOCKING HANDLE - Locks the miter saw at a
desired bevel angle,
BEVEL SCALE - To measure the bevel angle of the saw
blade O" to 45 ° left
COVER PLATE SCREW - Loosen this screw and rotate
the plata for access to the blade arbor locking boil

STOP LATCH - Locks the miler saw in the lowered
position for compact sloraga and ttarLsportation.
SWITCH HANDLE - The cutting head handle contains
the tr_gger switchand a safety lock-off Slide switch. The
_lade is lowered into the workpiece by pushing down on
the handle, 'The saw will return to its upright position
when the handle is released,
WARNING LABELS .- Read and understand for your
own safely. Aiways make certain the_e are in place &
legible.
WRENCH STORAGE - Convenient
misplacing the blade wrench

WOODWORKING

storage to prevent

TERMS

DUST CHUTE - Exhausts debds away Item the user,

ARBOR - The shaft on which a blade is mounted

EXTENSION WING - Exlends the width of the work
table for support while cutting long work pieces, They
can be used with or without a stop block as an additional
side fence,

BEVEL CUT - An angle cut made through the face of
Lhe workp|ece,

FENCE - Helps to keep the workpieca trom moving
when sav4ng Scaled to assist with accurate cutting

CROSS CUT - A cut made across the width or grain of
the workpiece,

HAND HOLD -Location of hands for transportation.

FREEHAND - Performing a cut without using a fence
(guide), hold down or other proper device to prevent the
workpiece from twisting during the cutting operation.

SAFETY LOCK-OFF BUTTON -YeIlow
button on
handle must be pushed lorward to activate the trigger
switch,
LOWER BLADE GUARD - Helps protect your hands
from the blade in the raised position, it refracts as file
blade is lowered,

COMPOUND CUT-A

simultaneous bevel and miter cuL

GUM - A sticky sap from wood products,
HEEL - MisaIignmenf of the blade.
KERF-The

amount of mater;el removed by blade CUL

MITER HANDLE -Used to rotate Ihe sew to the fight or
[eft cutting position,

MITER CUT - An angle cut made across the width or
grain of the workpiece,

MITER SCALE - To measure the 'niter angle 0_ to 45 °
left, 0 = to 45 ° fight.

RESIN - A sticky sap that has hardened.

MITER SPRING LOCK - Used in combination with the
miter handle, it locks the miler saw at a preset positive
stop for the desired miter angle,
MOUNTING HOLES - To mount the miter saw to a
stable surface,
ON/OFF TRIGGER SWITCH - To prevent tile trigger
|rom being accidentally engaged, a lock-off slide switch
is provided. To start the fool, push the lock-off slide
switch Ion,yard and squeeze the thgger Release the
trigger to stop the miter saw.

REVOLUTIONS PER MINUTE (RPM} - The r'=umber ot
turns completed by a spinning objecl in one minute,
SAW BLADE PATH - The area of the workplace or table
top directly in line with the travel of the blade or the parl
of the workpiece which wil! be cm,
SE'r - The distance between two saw blade tips, bent
oub,,,,ard in opposite directions to each other. The further
apart the tips are, the greater the set.
WORKPIECE - The item being cut. The surfaces o! a
workpiece are commonly referred to as faces, ends, and
edges°

ASSEMBLY INSTRUCTIONS
To avoid injury and damage to the saw, transport or store
the miter saw with the cutting head bcked in the down
position. Never use the stop latch to hold the cuing head

To avoid injury, do not connect this miter saw to the
power source until it is completely assembled and
adjusted, and you have read and understood this
Operators Manual.

in a do_

INSTALLING THE MITER HANDLE (FIG, A)
1.Thread the miter handie (1) into the hole (2) located at
the front of th_ miter table

pos:liO_for cutting operations,

Fig. C

Fig. A

Locking
When transporting or storing the miter saw. the cut'dng
he_d should atways be locked in the down position.
1. Push the cutting head (3) down to its lowest position.
2oPush ths stop latch (2) into the locking hole (4).
IMPORTANT; To avoid damage, never carry the miler
saw by the switch handle, the cutting arm, or the miter
table handle. ALWAYS use the designated carrying
handle.

SAW BLADE WRENCH [FIG. B)
1_For convenient storage and prevention of loss, there is a
slot (1) in the rear of the cutting head handle (2) for
storing the blade wrench I3) when not in use.

Fig. B
2

INSTALLING THE DUST BAG (RG, D)
1. Squeeze the metal collar wings (2) of the dust bag
(t).
2. Place the dust bag neck opening around the exhaust
pert (3), and release the metal collar wings
\

Fig. D

2
3

(

CUTTING HEAD (FIG. C)
Raising
t. Push down sllghtty on the cutting hat, die (1).
2. Pull out the stop latch knob (2).
3. Allow the cutting head {3) to rise to the up position.

Fig. F

INSTALLING EXTENSION WINGS (FIG, E)
To avoid injury or possible damage to the tool, support
long:work pieces by installing the extension wings to
extend the work support surface.
When using extension and stop block on the right side,
hold down clamp must also be In right side, Using
hold down clamp on the left side during this operation
can cause klck-back and serious injury to the
operator.
INSTALLING THE STOP BLOCK (FIG, E):
1. Stide the stop block (1) onto [he extension wing (2)
2, Thread the wing bolt (4) into the stop block and tighten.
INSTALLING THE EXTENSION WINGS (FIG. E):
1.Place the extension wing into the mounting holes (5)
provided in the miter saw base_
2.Thread the extension wing locking screw (6) into the
treaded hole (7) and tighten to secure extension in place.

(5) on the motor, below the miter
sew switch handle. (Fig, G)
7, Press the arbor lock, holding it in firmly while turning the
blade wrench clockwise. The arbor lock wtll engage after
turning the wrench. Continue to hotd the arbor locking to
keep it engaged, while turning the wrench clockwise to
loosen the arbor bolt,
B.Raise tho lower clear plastic blade guard (1) to the
upright position, (FIg, F)

Fig, G

REMOVING OR INSTALLATING

THE BLADE

Only use a lO-inch diameter blade. To avoid Injury
from an accidental start, make sure the switch is in the
OFF position and plug is not connected to the power
source outlet.
REMOVING {Fig, F, G, H)
1. Unplug the saw from the outfet,
2. Allow th_ blade a_embly to _e to the ut_._er_ost
posilion..Raise the lower blade guard (1) to the upper
position° (Fig, F)
3. Loosen the cover plate screw (2) with a Phillips
screwdriver (Fig, F)o
4. Rotate the cover plate (3) to expose the arbor bolt
(4) - (Fig. F).
5. Place the blade end wrench over the arbor bolt

REMOVING - cont'd
9. Remove the arbor bolt!washer (4), taser guide (6), and
the blade (7)o Do not remove the inner blade collar.
(FIg, H)
NOTE; Pay attention to thepieces removed, noting lhe]r
position and direction they Iase. Wipe the laser guide clean
of any SaWdUStbefore inslal]ing the new blade.

Fig,H

INSTALUNG BLADE (Fig, F, G, H)
1oInstal! a 10" blade, making sure the rotation arrow on the
blade matches the clockwise rotation arrow on the upper
guard, and the blade teeth are pointing downward,
2. Place the laser guide {6) against the blade and on the
arbor. 'Thread the arbor boll (4) into the arbor in a
counlerclockw_sedirection (Fig° H)
IMPORTANT: Make sure the rials of the laser guide are
engaged with the rials on the arbor shaft.
3, Place the blade wrench on the arbor bolt
4. Press the arbor lock [5), holding it in f_rmly wh:le turning
the blade wrench counferclockwise. When it engages,
continue to press the arbor fock in, while tightening the
arbor bol! securely, (Fig. G)
5. Rotate the cover plate (3) back until the slot in the cover
plate engages with tl_e cover pIate screw (2). Tighten the
screw with a Phillips screwdriver (Fig, F)
6 Lower the blade guard (1). (Fig. F)
7. Be sure the arbor lock is released so the blade turns
"freely.

ADJUSTING FENCE SQUARENESS (Fig. I)
1. Loosen lhetour fence tocking boils (1).
2. Using a square, lay the heel ot the square against the
blade, and the rule agoinst the fence (2) as shown.
3. Adjust the fence to be 9D_ to the blade and tighten lhe
four fence locking screws.
CAUTION: 11the sew has not been used recently, recheck
blade squareness to the fence and readjust if needed,

Fig, I

roTe avoid injury, never use the saW without the cover
plate secure in piece. It keeps the arbor bolt from
failing out if it accidentally loosens, and helps
prevent the spinning blade from coming off the saw.
• Make sure the collars are clean and properly
arranged. Lower the btade into the lower table and
check for any contact with the metal base or the
turntable.
• To avoid injury from an accidental start, make sure
ttie switch is in the OFF position and the plug isnot
connected to the power source outlet.

MITER gCALE (FIG. J)
The miler scale assists tile user in setting the desired miter
angtes from 470 Ieft to 47 = right. The miter saw table has
nine el the most common angle settings with positive steps
(3) at 0_, 15_, 22-5'_,31.6 _ and 45_. These positive slops
position the blade at the desired angle quickly and
accurately.

I2¸¸¸

1,
2.
3.

Fo Adjust Miter Angles:
L Unlock the miter table by turning the miter handie (1)
counterclockwise,
L While holding the positive-stop locking lever (2) down,
grasp the miter handle and rotate the miter table l_'t or
right to the desired angle_
3. If th_ desired angle is one of the nine positive stops,
release the positive.,stop locking lever making sure tile
lever snaps into posiUun.
t If the miter angle desired i$ no! one of the nine posffive
stops, simply lock the miter table into position by
turning lhe miter handte in the clockwise direction.
Vliter Angle Pointer Adjustment:
t, Position the miter table at zero degrees
Loosen the pointer screw (4) and adjust the indicator
to the 0" mark on the miter scale & retighten the

Lower the blade as tar as possible,
Loosen the lookout (3).
Turn the adjustment bolt (4) out (counterclockwise) to
decrease the cutting depth or in (clockwise) to
increase the cutting depth,
Rotate the blade manually to check for coniacL
Repeat until adjusted properly, and tighten the lockout
to secure the adjustment boil into position.

4.
5.

Fig. L

Fig. J

BEVEL STOP ADJUSTMENT" (F_g_M & N)

TO avoid Injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.

90" Bevel adjustment (Fig. M)
1. Loosen bevel lock handle (1) and tilt the cutting arm
completely to the right, Tighten the bevel lock handle,
2, Place a combination square (2} on the miter table with
the rule against the table and the heal of the square
against the saw blade,
3. If the blade is not 90 ° square with the miter table,
loosen the bevel lock handle, tilt the cutting head to
the left, turn the bevel angle adjustment bolt (3) in or
out with a 5me hex wrench until the blade is square
with the table.
4. Tilt the cutting arm to back to the right at 90 ° bevel and
recheck for alignment,
5_ Repeat steps 1 through4 if lurther adjustment is
needed.

CUTTING ARM TRAVEL (FIG. K)
Cutting arm pivot adjustmsnt
The pivot movement of the cutting arm (t) should not be
too tight; restricting movement, nor too loose; affecting the
accuracy of the saw cut. The correct lucking nut (2)
adjustment is snug, allowing no side-to-side arm
movement To adjust, tighten or loosen the adjusting nut
(2).

Fig. M

Cutting head downward travel adjustment

(Fig. L)

To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outleL

90' Bevel Pointer AdjustmEnt (Fig. N)
].

When
bevel
2. "Adjust
bevel

Before each culling operation, check the position o{ the
blade to make sure it does not contact any metal surface.
If the blade contacts any metal surface, the depth of travel
on the upper arm assembly must be adjusted.

the blade is exactly 90° to the table loosen the
indicator screw (5) using a Phillips screwdriver,
bevel indicator [6) to the "0" merit (7) on the
scale and retighten the screw.

e
e

To avoid injury from an accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet°

Support the saw on a }evel work surface.
Bolt or clamp the saw to its support

Place the saw in the desired location, either on a work
benchor recommended teg set. 3he base of the saw has
three mounting holes (1).
- For stationary use, fasten the saw to a workbench.
- For portable use, fasten the saw Io a 3!4" piece of
plywood. This mounting board can then be clamped to a
secure sudace

45 ° Bevel Adjustment (Fig N)
1. Unlock the bevel lock handle and tilt the cutting head
completely to the left
2. Using a combination square, check 1osee ff Ihe blade
angle is 45°t0 the table,
3. If the blade is not at 45 _to the miter table, lilt the
cutting arm to the dght, turn the bevel angle
adjustment bolt (4) in or out with a 5ram hex wrench
accordingly,
4. Tilt the cutting arm to the left to 45 = bevel and recheck
for alignment..
5. Repeal steps 1 _rough 4 until the blade is at 45° to
the miler table,

Fig.O
Portable Use

Fig. N

_4 inch Plywood

nary Use

MOUNTING THE MITER SAW (Fig. O)
To avoid injury from unexpected saw movement:
e Before moving the saw, disconnect the power cord
from the outlet, and lock the cutting arm in the lower
position using the stop latch,
NOTE: The stop latch is for carrying or storing the tool It is
NOT to be used holding the sew while cutting
e

e
e

Never carry the miter saw by the power cord or by the
switched handle. Carrying the tool by the power cord
could cause damage to the insulation or wire
connections resulting in electric shock or fire.
To avoid injury from flying debris, do not allow visitors
to stand behind the saw.
Place the saw on a firm, level work-surface where
there is room for handling and properly supporting the
workplace.

(1)

SAFETY INSTRUCTIONS
OPERATIONS
BEEORE

UStNGTHE

FOR BASIC SAW

[_FFER SAW

....

Keep all guards in place, in working order and properly
adjusted
If any part of this miter saw is missing, bent
damaged or broken in any way, or any =_lectrica]
parts d6fft work, turn the saw off an_ unplug tL_
Replace damaged, missing, or defective parts
before using the saw again,

To avoid mistakes that coufd cause serious,
permanent injury, do not plug the tool in until the
following steps are completed:
•

o
e

Maintain tools with care. Keep the miter saw
clean for best and safest performance. Follow
instructions for lubricating. Don't put lubricants on
the blade willie it's spinning.

Completely assemble and adjust the saw,
following the instructions. (ASSEMBLY AND
ADJUSTMENTS)
Learn the use and function o[ the ON/OFF s_tch,
lock-off switch, upper and lower blade guards,
SlOP latch, bevel lock handle, and cover plate
screws,
Review and understand all safety instructions and
operating procedures in this Operator's Manual
(SAFETY & OPERATIONS)
Review the MAINTENANCE and
TROUBLESHOOTING
GUIDE for your m_ter saw.
To avoid injury or possible death from electrical
shock:
Make sure your fingers do not touch the plug's
metal prongs when plugging or unplugging your
miter saw. (ELECTRICAL REQUIREMENTS
AN D SAFETY)

USE ONLY RECOMMENDED ACCESSORIES
o
Consult 1he ACCESSORIES and ATTACHMENTS
section of this Operators Manual ;or
recommended accessories Follow the
instructions that come with the accesso,_. The
use of improper accessories may cause risk el
injury to persons,
o

Choose the correct 10 inch diameter blade for the
material and the type of cu_ing you plan to do. Do
not use Thin Kerfblades.
Make sure the blade is sharp, undamaged
properly aligned. Wilh the saw unplugged,
the cutting arm elf the way down. Manually
the blade and check for clearance, T_ltthe
head to a 45 _ bevel and repeat the test.

BEFORE EACH USE
Inspect your saw.
e
Disconnect the miter saw, To avoid injury
from
accidental starting, unplug the saw before any
adjustments, including set-up and biade changes.
Compare the direction of rotation arrow on the
guard to the direction arrow on the blade. The
blade _eeth should always point downward al the
front of the saw.
o

Remove all adjusting wrenches from the tool
before turning it on

and
push
spin
miter

Make sure the biade and arbor coliars are clean.

Make sure all clamps and locks are light and
there is no excessive play in any parts.

KEEP YOUR WORK AREA CLEAN
Clultered areas and benches invite accidents.

Tighten the arbor bolt,
Tighten the cover plate screw.
Check for damaged parts, Check for:
o
Alignment of moving pans
o
Damaged electric cords
o
Binding of moving parts
a
Mounting holes
•
Function of arm return spring and lower
guard:
Push the cutting arm all the way down, tI_en
lel it dse until it stops. The lower guard
should fully close. Follow instructions in
TROUBLESHOOTING
GUIDE for

To avoid burns or other fire damage, never use the
miter saw near ffammab]e liquids, vapors, or gases,
m
Plan ahead to protect your eyes, hands, face
and ears,
e
Know your miter saw.
Read and understand the Operator's Manual and
tabels_affixed to the tOOL Learn its application and
]]inflations as well as the specific potential hazards
specific to this tool. To avoid injury from accidental
contact with moving parts, don't do layout, assembly,
or setup work on the miter saw.
o
Avoid accidental starting
Make sure the switch is OFF before plugging the
miter saw into a power outlet.

adjustment i! necessary
Other conditions that may affect lhe way the
miter saw works

PLAN YOUR WORK
o

Use the tight tool, Don't force a too] or attachment
to do a job it was not designed to do, Use a
different tool for any workpiece that can't be held
- • in a-solidly braced, fixed position ......
- ....
o

CAUTION; This machine is NOT designed for cutting
masonry, masonry products & ferrous metals (steel,
iron, and iron-based metals ,) Use this miter saw to cut
only wood and wood by-products. Other material may
shatter, bind the blade, or create other dangers,
Remove eli nails that may be in the workpiece to
prevent sparking that could cause a fire.

workpieee, fence and table that will let the
workpiece shift after ff is cut.
Keep the cut off piece free to move sideways after
it is cut ell Otherwise, it could get wedged
against the blade and thrown vioIenw,
Only lhe workplace should be on the saw's table,
Secure work. Use clamps or a vise to help hold
the work when it's practical.

USE EXTRA CAUTION WITH LARGE OR ODD
SHAPED WORKPIECES.
Use extra supports (tables, sawhorses, blocks,
etc,) for workpieces large enough to tip°
O
Never use another person as a substitute for a
table extension, or as an addilJonal support for a
workplace that is longer or wider than the basic
miter saw table, or to heJp feed, support, or pull
the workplace.
=_ Do not use this saw to cut small pieces, It the
workplace being cut would cause your hand or
fingers to be within 7-tt4" inches of the saw blade
workpiece is too small Keep hands and fingers
out of the =no hands zone" area marked on the
saws table.
e
When cutting odd shaped wolf{pieces, plan your
work so it will not bind in the blade and cause
._ossible injury. Molding, for example, must lie flat
or be held by a fixture or jig that will not let it move
when cut.
o
Properly support round material such as dowel
rods. or tubing, which have a tendency to roll
when cut, causing the blade to "bite".
•

DRESS FOR SAFETY
Any power tool can throw foreign objects into tt3e eyes.
This can result in permanenl eye damage. Everyday
eyeglasses have only impact resistant lenses and are
not safety glasses. Glasses or goggles not in
compliance with ANSI Z87 1 could seriously injure you
when they break.
e
Do not wear loose clothing, gloves, neckties or
jewelry (rings, watches). They can get Caught and
draw you into moving parts,
•
Wear non-slip footwear,
e
Tie back long hair,
=
Roll long sleeves above the elbow.
e
Noise levels vary widely, To avoid possible
heating damage, wear ear plugs when using any
miter saw.
e
For dusty operations, wgar a dust ma_k along
with safety goggles.

To avoid injury, follow all applicable safety instructions,
when cutting non-ferrous metafs:
e
Use only saw blades specifically recommended
for non-ferrous metal cutting.
e
Do no! cut metal workpieces that must be hand
held. Clamp workpieces securely.
•
Cut nonferrous metals only if you are under the
supervision of an experienced person.

INSPECT YOUR WORKPIECE
Make sure there are no nails or foreign objects in the
part of the workpiece being cut.
Plan your work to avoid small pieces that may bind,
or that are too small to clamp and get a solid grasp
on.

Plan the way you wilt grasp the workpiece from start to
finish. Avotd awkward operations and hand positions,
A sudden slip could cause your fingers or hand to
move into the blade.

WHEN SAW IS RUNNING

DON'T OVER-REACH
Keep good footing and balance, Keep your face and
body to one side, out of the fine of a possible kickback,
NEVER stand in the line of the blade,

Don't ..................
frequent use of your miter
saw to result in a careless mistake. A caretess fraction
of a second is enough to cause a severe injury.

Never cut freehand#
e
Brace your workpiece firmly against the fence and
table slop so it will not rock or twist during the cut,
e
Make sure there is no debris between the
workpiece and the table or fence

Before cutting, il the saw makes an unfamiliar noTse or
vibrates, stop immediately. Turn the saw OFE Unplug
the saw,, Do not restart until finding and correcting the
problem.

TURNING THE SAW ON (Fig, Q)
To reduce the likelihood of accidenta! starting, a thumb
activated lock-OFF switch is located on top of the
switcll handle, The safety lock-OFF button (1) must be
pushed forward before the trigger switch (2) can be
activated and the miter saw started.
Make the switch child-proof. Insert a padlock through
the hole {3) in the trigger switch and lock _L This will
prevent children and other unauthorized users from
turning the swttch ON,

BODY AND HAND POSITION (FIG P)
Proper positioning of your bedy and hands when
operating the miter saw will make cutting easier and
safe_ Never p!ece hands near the cutting area. Position
hands at least 7-1/4" away from the path of the blade.
Hold workpiece firmly against the fence to prevent
movement toward the bfade. Keep hands in position
.until the.tr_gg_=rhas been released and the blade has
completely slopp_d Before rnal_ing ,_cut, _vit5 the .....
power switch in the OFF position bring the saw blade
down to the workpiece fo see the cutting path of the
blade.
•
Keep children away. Keep all visitors a safe
distance from the miter saw. Make sure
bystanders are clear of the miter saw and
workplace°
e
Don't force tool It will do the job better and safer
at its designed rate Feed the saw into the
workplace slowly with a firm downward mot.fen,
o
Before freeing jammed material:
e
Turn switch OFF.
a
@
@

Unplug the miter saw,
Wait for all moving parts to stop,
After finishing a cut, keep holding the upper
blade assembly in the down position,
e
Release the switch, and wait for all moving
parts to stop before moving your hands
11the bfade doesn't step within 6 seconds, unplug
the saw and folIow the instructions in
TROUBLESHOOTING
GUIDE section for
adjusting the blade brake before using the saw
aoain.

THE LASER -TRAC _
Your tool is equipped with our latest innovation,
the Laser -Tree _, a battery powered device using
Class TI][a laser beams. The laser beams will
enable you to preview the miter blade path on the
workpteea to be cut before you begin your
operation,

Laser is activated when blade is rotating Do not stare
into beam or view directly with optical instruments, Do
not remove the warning label affixed to the blade
guard. Avoid direct eye contact with light source.

Fig. P

NOTE .The red laser line wilt appear as a dotted line
when the motor is activated and the blade assembly is
in the uppermost position. This b?oken line will assist
you in aligning the mark on your workpiece with the
cutting path of the saw blade. As you lower the blade
assembly, the retractable guard will llft and turn the
broken line into a solid red laser line.
Laser Warning label: Max output <5roW DIODE
LASER: 630-670nm, Complies with 2 tCFR 1040.10
and 1040° 11.
OPERATION OF LASER
With the blade assembly in the uppermostpositient
1 Position yourwo_kpiece ontothe miter saw,
2. Turn on the m_tersaw to activate the laser beam.
3 Verify the laser beam i_ _ligned with the mark on
the workplace (WARNING - Do not lower the blade
assembly duringthe alignment process).
4 If the mark on the workplace is not aligned with the
dotted laser Dine,turn oft machine, wait for the blade to
stop and repositionworkpiece
5. Turn on the miter saw and verifyalig nment.
6 Once alignment is achieved, secureworkpiece with
a clamping device and perform the cut

[

1
t

®,

I
[
I

®
6 lt2 po

MITER CUT (FIG. R)
When a miler cut is required, un}ock the miler table by
tuming the miler handle (1) counterclockwise. While
holding the miler handle, press down on the positive
stop locking lever (2). Rotale lhe miler table to the
right c r Ieli with the miter handle. When the table is in
the desired positlon as shown on the miler scale (3),
release the positive slop locking lever and tight_n the

COMPOUND CUT (FIG. T}
A compound cut is the combination of a miler and a
bevel cul simullanaausly.
1 Loosen 1he bevel lock handle (1] and position the
culting bead al lhe desired bevel posillon. Lock the
bevel lock handle.
2. Loosen the miler table lock handle (2) Press down
. _ positive slop (e_Wng laver.(3) and posWon .the
table aI the desired angle, Release the posilive
slop locking lever and lock the miter handle

angle Positive slops are provided at 0°,15".22.5",3t 6"
and 45°_
IMPORTANT: Always lighten the miler table lock
handle before performing a cut.

Fig, T

Fig, R

CUTTING BOWED MATERIAL (FIG. U)
A bowed workplace must be posilioned against the
fence and secured with a clamping devise before
cutting, Do not position workplace incorrectly or try to
cut Ihe workp)ece without Ihe support ot the fence.
]'his will cause lhe blade to bind and could result in
personal injury.

BEVEL CUT (FIG. S)
When a beret cut is required, loosen the bevel lock
handle (1}. Till the culling head to the desired angle as
shown on the bevel scale (2). The blade can be
positioned at any angle, from a 90 _straight Cut (0 ° on
lhe scale) to a 45 ° left bevel, "l'ighlen the lock handle
(!) lo lock [he desired culling heed in position. Positive
slops are provided at0 and 45 _,

Fig, U
. ._

WORKP|ECE SUPPORT (FIG. V)
Long pieces need extra support° The support should
be placed under the workpiece. Keep your hands out
of the "no,-hands" zone, positioned 7.o1/4" or more
a.wayli'0rn t_'6l_de,
The Suppod must:iet the -._-__
Workp_ece lay flat on the worktabte during the cutting
operation.
NOTE: When mounted on a fiat surface, the miter saw
table is 3-1/8 inches high

Fig, V

AUXILARY WOOD FENCE (FIG, W}
When making multiple or repetitive cuts thai result in
cut-off pieces of one inch or less, it is possible ior the
saw blade to catch the cut-otl piece and throw it out o!
the saw or into the blade guard and,hous{ng, p_ssib!y,.
causing damage or injury. To minimize thls an auxilia_
wood fence can be mounted to your saw
Holes are provided in the saw fence to attach an
auxiliary wood _ence. This fence is constructed of
straight auxiliary wood approximately 3/4 inch thick by
2-1/2 inches high by 18 inches long.
Attach the wood tence securely and make a full depth
cut to make a blade slot.
Check for intederence between the wood fence and
the lower blade guard. Adjust if necessary.
NOTE: This auxiliary fence }s used only w_th the saw
blade in the 0" bevel position (90" to the table)., The
auxiliary wood fence must be removed when bevel
cutting

Fig. W

Cu_ting capacity with auxY[ia_ _ence
Crosscut
Miter 45'R. & L

_t2"
!3q12" x 2"

Bevel 45L.
Compound

3,1/8"

_1/2"
45'L.,45R

& L,

_2" x 2"

CUTTING A DIMENSIONAL 4X4 WITH ONE CUT
(Fig. X)
A dlmensiona,' 4x4-in may be cut in hail with one cut
by attaching an auxilia_ wood fence of 314 inch thick.
See "AUXILIARY WOOD FENCE" above=

CUTTING BASE MOLDING (FIG, Z)
Base me)dings and many other moldings can be cut
on a compOLmdmiter saw, The setup of the saw
depends on molding characteristics and appTications,
as shown. Perform practice cute on scrap materia! to
achieve best results;
1. Aiways make sure moldings rest firmiy against fence
and table. Use hoJd-down or C.clamps, whenever
possible, and place tape on the area being clamped
to avoid marks.

" : ....

Fig. X
Auxlilary fence

3-1/2"---.-._1

4,--

I
Mitre saw f._.,_ence/'_
3..U2"
'_

--.'---

cuLtypically
Mark cuthappens
}ine direct}y
the tape,
3. making
Splintering
due on
Io wrong
blade
application and thinness of the material
2. Reduce sp)intering by taping the cut area prior to

}

Fig.z
}

Mitre saw Gable

VERTICAL MITER CUTTING (RG. Y)
To make a miter cut in a 2x4 wod_piece (1-5/8" x 3-1/2")
in the vertica_position on edge a spacer such as the
auxiliary Wood fence described in the "AUXILIA RY
WOOD FENCE" section is required

__F
ML_orsaw '_ab_o
Mtlor ia145'3, beV_" at C_'

NOTE: Always perform a dry run cut so you can
determine if the operation being attempted is possible
before power is applied 1o the saw.

Fig. Y
,Work,piece
Auxiliary fen_

b,.1.Sf8-

_ _

I
|,

M{{Or at O_, bevel at 45"

Mitre
saw
table
l,

CUING
CROWN MOLDING (FIG, AA, BB)
Your compound miler saw is suited for the difficult task
of cutting crown molding, To fit properly, crown molding
must be compound-mitered with extreme accuracy.
The two surfaces on a piece of crown molding that fit
fiat against the ceiling and wall are at angles that,
when added togelher equa! exactly 90"
Most crown molding has a{op rear angle (the'secti0n

Fig. BB
Settings for standard crown molding lying flat on
compound miter saw table
Inside comer
.....

that fits fiat against the ceiling) of 52_and a bottom rear
angle (the section that fits flat against the wall) of 38°+
::
In order to accurately cut crown molding for a 90 _
inside or outside comer, lay the molding with its broad
back sudace fiat on the saw table.

IL
Outside comer
Compound cut crown moldings

When setting the bevel and miter angles for compound
miters, remember that the settings are interdependent;
changing one changes the other, as welt. Also keep in
mind that the angles from crown melding are very easy
for these angles to shift slightly, nit settings should be
fesled on Scrap molding.

Bevel/Miter

Settings

KEY IBEVEL" ]MITER l
TYPE OF CUT
_INGJS,
ETTING
.. .
Inside corner.Left side
1,Pesiti0n top el molcling against
IL
33.9_
31.6D
fence,
Right
2,Miter table set at RIGHT 31.6 ",

Fig. AA

33,9=

31.6_'
Left.

&LEFT side ts finished piece,
Inside,col'net-Right
side
1,Position bottom of molding
against fence,
2Miter table set at LEFT 31,6",

3.LEFT side is finished £bce,
Outside corner-Left,s!de
:
31.6° "": 1.Position bottom of melding :
[.eft
against fence,
:
2,Miler table set at LEFT 31,6'%
&RIGHT side is £nished piece.

i33-9'_

1_3.9_

31.6`_

1.Position top of molding aga nst

Right

__
Miter table set at RIGHT: 31.6°.
fence.
3,RIGHT s de s linished piece.

e
n
C
o

Outside #orn£r-Right

.Mite_ 5RW

l_b]_

_
i

CHANGING THE BATTERIES
a
Unplug your saw.

(Fig. CC)

t
FIG. CO

::Failure to:unplug your saw could result in accldenial
starling causing possible serious personal injury.
1_ Remove the laser guide from the saw.
2. Loosen and remove the two screws (1) then
remove lhe laser guide cover.
&
Remove the three batterbs by sliding them out
from their mounting braces using a
n0n-:conductive devbe such as a toothpick.
4.
Rep}ace:the batterie_thathave,_
ratirL_tof 1.5
volts (Number LR44)..
5, Replace the laser guide cover, two screws and
:
laser assembly onto the miler saw.
: Note: : i: .... ........
'
:When replac(ng the batteries, the battery cover
should be thoroughly d_aned, Use a soft paintbrush
o_"similar device to remove all sawdust and debds.

s!de

LOWER BLADE GUARD

MAINTENANCE
DANGER
Never put lubricants on the blade while it is spinning.

To avoid fire or toxic reaction, never use gasoline,
naphtha acetone, lacquer thinner or simifar higllly
volatile solvents to clean the miter saw.

Do not use the saw without the lower btade guard°
The lower blade guard is attached to the saw for your
protection. Should the lower guard become damaged,
do not use the saw until the damaged guard has been
replace& Develop a regular check to make sure the
lower guard is working properly. Clean the lower
guard of any dust or buildup with a damp cloth.
AUTtON: Do not use solvents on the guard. They
coutd make the plastic "cloudy" and briWe.

To avoid injury from unexpected starting or electrical
shock, unplug the power cord before working on the
saw.

For your safety, this saw is double4nsulated. To avoid
electrical shock, fire or injury, use only Darts identical
1othose identified tn the parts list Reassemble
exactly as the original assembly to avoid electrical
shock.

REPLACING CARBON BRUSHES (FIG. DO)
The carbon brushes furnished will lest approximately
50 hours of running lime, or 10,000 ONtOFF cycles.
Replace both carbon brushes v,,l_eneither has less
than 1/4' length of carbon remaining, or if the spring
or wire is damaged or burned, To inspect or replace
brushes, first unplug the saw. Then remove the black
plastic cap {1) on the side of the motor (2), Remove
the cap cautiously, because it is spdngtoaded.. Then
pull out the brush and replace, Replace for the other
side. To reassemble reverse the procedure.. The ears
on the metal end of the assembly go in the same hate
the carbon part fits into. Tighten the cap snugly, bul
do not ovedighten.

SAWDUST
Periodically, sawdust wiil accumulate under the work
table and base. This could cause difficulty in the
movemenl of the worklable when setting up a miter
cut. Frequently blow out or vacuum up the sawdust

tf blowing Sawdust, wear proper eye protection to
keep debris from blowing into eyes

LUBRICATION
All the motor bearings in this tool are lubricated wilh a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions; therefore,
no further lubrication is required.
Lubrication the Following as Required:

NOTE: To reinslal! the same brushes, first make sure
the brushes go back in the way they came out. This
will avoid a break-in period that reduces motor
performance and increase wear.

Fig. DD
2

When cleaning the lower guard, unplug the saw from
the power source receptacle to avoid unexpected
startup.

Choppivot, light machine oil or aerosol wi]t penetrate
from the ends of the junction points. A qualilied
service technician can remove the PiVOtupstop to
relieve tension, end the 2 metric set screws holding
the shaft, in order to drive the shaft about 3[4" right
Exposed surfaces are Iubdcaled with automotive type
ell
Central pivot of plastic guar_ Use light household oil
(sewing machine oil ) on metal-to-metal or
metaI4o-pIestic guard contact areas as required for
smooth, quiet operation. Avoid excessive oil, to which
sawdust Will cling.

\
Link': (which actuates the lower guard movemenl)
may be oiled at the rear pivot, greased at ball beadng
contact, and oiled where the link actuates the acetyl
roller of the lower guard, ;f the down chop motion is
I_ard to start,

i ¸¸/

:--::,;

;

......

To avoid injury from accidental starting, always turn switch OFF and unp{ug the too! before moving, replacing the blade
or making adjustment.

.......

....

Consult your Sears service Center if for any reason the motor will not run.

TROUBLESHOOTING

GUIDE - MOTOR

PROBLEM

Brake does net
stop blade within
6 second&

1,Motor brushes not
sealed or lightly
sticking.
2. Motor brake
overheated from use
of defective or wrong
size blade or rapid
ON/OFF cycling,
3, Arborbolt
loose.
4. Other.
1. Fuse

Motor does not
start

Excessive brash
spark when
switch released.

TROUBLESHOOTING

CAUSE

SUGGESTED

CORRECTIVE

ACTION

1. Inspect ! clean f replace brushes. See
MAINTENANCE section.
2. Use a recommended blade,
Let cool down.

& Retighten arbor boll,
4. Sears Service Center.

1. Use & check t 5-Amp time delay fuse, or circuit
breaker.
2. See MAINTENANCE section_
3. Sears Service Center.
1_Replace Brushes,

2. Brush worn.
3. Other.
1. Fuse
2. Brush worn.
3. Other.

GUIDE - SAW OPERATION

PROBLEM

PROBLEM CAUSE

SUGGESTED CORRECTIVE

Blade hits table.

1. Misalignment.

1.
2.

Angle el cut not
accurate,
Can't adjust miter.

1. Miler table locked.

1.,Push positive stop locking lever clown and
rotate table.
See OPERATION Section,
2, Vacuum or blow out dust,
WEAR EYE PROTECTION,
1. See ADJUSTMENT Section,

Cutting arm
wobbles,
Cutting arm won't
fully raise, or
blade guard won't
fully close.

Blade binds, jams,
g_rn$ woad,

Saw vibrates or
shakes.

2. Sawdust under table.

1. Loose pivot points.

See ADJUSTMENT section.
Sears Service Center

1. Part failure.
2. Pivot spring not
replaced propedy after
service.
3. Sawdust build-up.
1,,Improper operation.
2. Dull blade_
3. Improper blade size_

1. Sears Service Center.
2. Sears Service Center,

4, Warped blade.
1.Saw blade not round,
2.Saw blade damaged.
3.Saw blade loose.
4.Other.

4. Replace blade.
t_Replace blade.
2,Replace blade.
3. Tighten arbor screw.
4.Sear Service Center.

ACTION

3. Clean and lubricate moving parts.

1 See BASIC SAW OPERATION section,
2. Replace or sharpen blade.
3, Replace with 10" diameter btade.

10" MITER SAW PARTS LIST

MODEL:

137,212140

When servicing use onlyCRAFTSMAN replacement par|so Use of any other parts may create a HAZARD or
cause product damage,

Any attempt to repair or replace electrical parts on this miter saw may c_eatea HAZARD unIess repair is done by
a qua||fled servicetechnician, Repairservice is avai}able at your nearest Sears Service Centers
Always order by I.D, Number
PARTS LIST FOR SCHEMATIC
LD.NO

A
Siz.e

Description

LD.NO

D¢_¢rtpf.lon

OK2S

HE×_SOC}_"T

BP_,J

CRRE

SLEEVE

Ol,_B

CR I1E.COUt_T

HO,SCR

POINTER

O),_C

CR BE COU_#T

_'tD SCR EW

FOLLOW_= R PLATE

0K'TZ

CB RE,TRUSS

HD ROUND

NECK SCRI

M5 _1_0d4

O_IJ

Ti_BLE

'€

0KTZ

CR R_LTRU_;S

HB ROU_D

NSCf;

M_" 1 O 14

0B=K

31LT1NG

oR9×

DRIVE

_-tU

SUPPORT

OK_

CR nE PAN HD TAPPING

DR21

BRACEET-T/LT

0){_D

CR RE PA_

D_24

EHAFT-P(VOI

GKCX

CR.RE.PAN

0){D: t

CR _E PAN

H0 T@PIh'G

t_4"0

7 1()

DKOM

CR RE.PAN

HO SCt_E'W

t_5"0

B,'20

OBt 2

COIL

SPRING

OBla

CLAMP

OBIA

PLAST)C

DBID

NEEDLE

_IG

HANDLE

INSERT
SCALE

POINTER

Size
HD.CAP

SOREWB

PAN HD TAPPING

SCREW
EW

SCREW

HD T/-_PPIhfG

SCRI

Qty.

M_'l.ZB-20

M._ "0.7-1(:(

I',_5_0.8-12

M_I

,O+lo

SCJ3_V

1_4"10-_5

SCREW

t/,_-'O IB._.5

SCREW

I_*,5"O,S 1D

0_26

NEEDLE
ROIA'rIO,'_

0_,,?.9

AICGLE

PEGBLATOR

0F, t}N

cR_nE_PAN

_IB,SCRF_W

t/_.r_"[; _,25

0_1

SHAFT

5LF__VE

0F.DR

CR RE.PAN

HD, SCREW

_5'0

O_3S

T_tOGER

01_DR

CR.RE,PAN

HD SCt4E_q

M5°0_B-I{)

O£L3Y

C;OMPRES_ION

DI{DT

CR,REPAN

HB SCREW

M_'I

{)-B

0_3Z

CLAMP-CORD

0_ED

CR.RE.PAP;

HB,SCREW

t_B'i

0-_{)

DB4W

LABEL

0Kh'3

HEXNUT

1._,57 0

0C_S

COMPRESSION

O_QX

)_E_

I,'B'_

0KO){

_JUT C_tUC_<

_._S'_ ,O T_B

OKOZ

NUT CHUCK

!,110'(

$ T=IO

OKFt0

tqUT C( (UCR

M12"1

75 T_I2

DKUX

I'ERI_TNAL

PLATE

SPRING

_P_IlI_G

W_RS

_PI_IN_

OOt,_Z

V(BI_ O_t*.Rtt(_

DC_H

LOCKI_,*G

HANDLE

DCVS

BAG-DUST

ABB'Y

ODTW

BRACKET

{)QOI

GUA_O-CQRI.3

_DTX

_HAFT

BS1N

AR)_MIT_R

0OTZ

KNOB-HAP_DLE

O_ 1P

TABLE

0DB7

TORSION

0S1S

COLLAR

{)[_10

SHIM

{)SIT

HOUBING

OO3B

_CHOR

BLOCK

OS2B

CR RF-PAN

{)D_FI

CAUTION

Lt_._ E L

0BTZ

LABEL

BOS_

CH_P_ PLA_t_

{)V_

P_WER

0DR;

RUBBER

PAD

{)V_

PENCE

ODHT

SPRING

GUARD

OVgJ

_,_OTOR

0DTZ

f,J3'3 0 R COLLAR

O_K9

BUT70_

{)DVJ

WRENCH

_KA

SE_I_T

DDWLt

_TDPASM

OXO5

HANDLE

_DWW

F..XTF-_T_ON WING

BXO_

HANDLE

0J_IJ

FLAT WABHE(_

_10_20

20ZD

LEVER

OJ_.R

FLAT WASHER

_I_I{)'BO

2tOg

LIMIT

OJTR

FLAT WASHER

112°_-315€

211{2

B,¢_SE

OJMM

O_RING

2tK3

WING

{L;PE

HEX HD.BOLT

23E0

SRACI|qG

23PP

BLJ_D_

2-_|'_Z

ARBOR

25_5

PC GUARD

25Q0

TRADEoMARK

20V, YS

|J:0"_ OR LABEL

A_ S'Y
AS5_'/

S'_OP

SPRING

HEX
LERGTH

ROD
M5"1J3_20

DJOT

I(EX,HD,_OL_

{)JUK

HEX_E{_.I(D.CAP

DJVY

H_X

OJZJg

HE3r_DC.SET

_GREV,t

!,LB_O _IO

DJT_F

HEX.SOC.SET

BCR_V(

t:AS'I.D* 1O

OJ"Z_

IIEX WASHER

HD BOLT

MO "1.?..5-2{)

0_O\V

HEX HD SCRE_,V

{)K24

)4F..X $OCKE'_

0K2N

HEX SOCKET

S_.C.HD

_-7S

MIO'i
BOLT

l._,_'l

0 16

CAP BOLT

M.5"l

{)o16

AND WASHBR

M_-I

(}o_5

HD CAP _CRE_._,'S

MB'I 25.35

HD CAP SCREWS

t _5-25

B_0

'_=5

{) T=_

,_B_EMBL¥
HB ¸TAPPING

SCREV_

M6"1

D-2_;

_A_LE

BW_TCH
_A_EL_
COVER

SWITCH

BOLT

f,_,B"I 0-20

PLAT_

C_LLAR

27_L

WARNING

2ERV

INSTRUCTION

SC_=-%_I

NUT

{)CK_

*:_2_3 5

_:_2B

_LIDE

OP LASER

LABEL

LA_EL

I;fAt,_UAL

A_Y

•

10'_ COMPOUND
: SCHEMATIC

MITER

MODEL;

SAW

137.212140

10" COMPOUND

MITER

PARTS LIST FOR SCHEMATIC

I,D. NO.
0HV5

MODEL:

SAW
B

137.212140

MOTOR

DESCRIPTION
BALL BEARING

SIZE
6204LEU

QTY

0HX9

NEEDLE BEARING

HK_]010

OJEB

C-RING

A,,14

OJEG

C-RING

A.20

0JG7

PARALLEL KEY

OJX2

HEX.SOC SETSCREW

MS=0.B-6

0K3A

M5"0.8-30

0K7G

CR..RE.PAN HD°TAPPING
SCREW&WASHER
CR, RE,ROUND HD, WASHER SCREW

OKLA

PLASTIC SCREW

OQgK

FLOW GUIDE

0QGR

COMPRESSION SPRING

DQM4

ARBOR SHAFT

0QM7

BEARING COVER

0QM8

HELIX GEAR

0QME

BRACKET STOP

0QMK

PLASTIC CAP

0QMR

ARMATURE

0QMX

FIELDASS'Y

0QMY

WIRE PROTECTOR

]

OQMZ

MOTOR

OQQS

BRUSH HOLDER

0QQT

BRUSH ASS'Y

0QR0

BRUSH COVER

OQR2

BEARING BUSHING

1102

SPRING PIN

110A
! 44L

CR.RE.PAN HD,TAPPING
SCREW&WASHER
LEAD WIRE ASS'Y

148B

UPPER ARM

ASS'Y

HOUSING

ASS'Y

M5° 12-55

I
!

10" COMPOUND
SCHEMATIC

MODEL:

MITER SAW

137.212140

MOTOR

\
\

/
/

/
/
/

_()

N_
Z

Your Home
For repair-in

your home-of

all major brand appliances,

lawn and garden equipment, or heating and cooling systems,
no matter

who made _t, no matter

who sold

it!

For the replacement parts, accessories and
Operator's

Manuals

that you need to do-it-yourself,

For Sears professional installation of home appliances
and items like garage door openers

1-800-4-MY-HOME

and water heaters.

(1-800-469.4663)

Call anytime, day or night (U.S.A. and Canada)
wwwosears.corn

www.sears.ca

Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, carl or go on-line for the location of your nearest
?: i

...... ;/

;'_c

www.sears.ca

S_,_rs, Roebud_and Co.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 28
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sun Oct 21 03:19:05 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 137212140 User Manual MITER SAW Manuals And Guides LR708226

CRAFTSMAN Miter Saw Manual LR708226 CRAFTSMAN Miter Saw Owner's Manual, CRAFTSMAN Miter Saw installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation