Craftsman 141218331 User Manual SAW TABLE^ Manuals And Guides 1310502L

User Manual: Craftsman 141218331 141218331 CRAFTSMAN SAW TABLE^ - Manuals and Guides View the owners manual for your CRAFTSMAN SAW TABLE^ #141218331. Home:Tool Parts:Craftsman Parts:Craftsman SAW TABLE^ Manual

Open the PDF directly: View PDF .
Page Count: 36

Download
Open PDF In Browser	View PDF

Operator's Manual

1 O"

CONTRACTOR TABLE SAW
Model No.
351.218331

. Safety
• Unpacking
• Assembly
• Operation
= Maintenance
• Parts List

CAUTION:
Read and follow all Safety
Rules and Operating
Instructions before First
Use of this Product. Keep
this Manual with Tool.
Sears Brands Management
wv,rw,craftsman.com

36998.01 Draft (05/24113)

• Espa_ol
Corp.,

Hoffman

Estates, IL 60179 U.S.A.

Warranty .........................................

Safety Rules ....................................
Unpacking ......................................
Assembly .....................................
installation ....................................

2-5
5-6
6-13
13-14

Operation ....................................
Maintenance ....................................

14-19
20

Troubleshooting ...............................
Repair Protection Agreement .......................
Parts Illustration and List ........................

22-23
23
24-35

Espaffol ......................................

36-59

CRAFTSMAN

ONE YEAR

FULL WARRANTY

FOR ONE YEAR from the date of purchase, this product is
warranted against any defects in material or workmanship.
Defective product will receive free repair or free replacement if
repair is unavailable.
For warranty coverage details to obtain repair or replacemerit, visit the website: www.craftsman.com
This warranty does not cover the blade or belt, which is an
expendable part that can wear out from normal use within the
warranty period.
This warranty is void if this product is ever used while providing commerciaI services or if rented to another person.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates,
IL 60179

WARNING:
For your own safety, read all of the instructions
and precautions before operating tool.
PROPOSITION
65 WARNING:
Some dust created by using
power tools contain chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

•

Wear protective hair covering to contain long hair.

•

Wear safety shoes with non-slip soles.

Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses. They are NOT safety glasses.

°
°

Wear face mask or dust mask if operation is dusty.
Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.

PREPARE

WORK

AREA

FOR JOB

Keep work area clean. Cluttered work areas invite accidents,

Do not use power tools in dangerous environments. Do not
use power tools in damp or wet locations. Do not expose
power tools to rain.

Work area should be properly lighted.

Keep visitors at a safe distance from work area.

Keep children out of workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to
prevent any unintentional use of power tools.

Keep power cords from coming in contact with sharp
objects, oil, grease and hot surfaces.

TOOL SHOULD

BE MAINTAINED

Always unplug tool prior to inspection.

Consult manual for specific maintaining and adjusting procedures.

Keep tool lubricated and clean for safest operation.

Remove adjusting tools. Form habit of checking to see that
adjusting tools are removed before switching machine on.
Keep al! parts in working order. Check to determine that
the guard or other parts will operate properly and perform
their intended function.

Check for damaged parts. Check for alignment of moving
parts, binding, breakage, mounting and any other condition that may affect a tool's operation.

A guard or other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs.
(Use parts list provided to order replacement parts.)

•

Maintain proper adjustment

Never adjust saw while running. Disconnect power to avoid
accidental start-up.

Lead from lead-based paints.
Crystalline silica from bricks and cement and other
masonry products.
Arsenic and chromium from chemically-treated lumber.

Have damaged or worn power cords replaced immediately.

Keep blade sharp for efficient and safest operation.

Your risk from these exposures vary, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area and work with
approved safety equipment. Always wear OSHA/NIOSH
approved, properly fitting face mask or respirator when using
such tools.

Use right tool for job. Do not force too] or attachment
a job for which it was not designed.

.
°

Disconnect tool when changing blade.
Avoid accidental start-up. Make sure that the tool is in the
"off" position before plugging in, turning on safety disconnect or activating breakers.
Do not force tool. It will work most efficiently at the rate for
which it was designed.

•
•
•

CAUTION: Always follow proper operating procedures as
defined in this manual -- even if you are familiar with use of
this or similar tools. Remember that being careless for even a
fraction of a second can result in severe personal injury.
WARNING: THIS PRODUCT CONTAINS LEAD. A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.

BE PREPARED FOR JOB
•

Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of machine.

Sears Brands Management

Corporation

KNOW

HOWTO

of rip fence and blade guard.

USE TOOL
to do

Keep hands away from blade and moving parts and cutting
surfaces.

Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.

°
.

Do not overreach. Keep proper footing and balance.
Never stand on tool. Serious injury could occur if tool is
tipped or if blade is unintentionally contacted.
Know yourtoo]. Learn the tool's operation, application and
specific limitations.

Handle workpiece correctly. Press firmly against table.
Protect hands from possible injury.

•

Turn machine off if it jams. Blade jams when it digs too
deeply into workpiece. (Motor force keeps it stuck in the
work.)

•

Feed work into the blade only as recommended in
"Operation"

Never turn the saw ON before clearing the table of all
tools, wood scraps, etc., except the workpiece and related
feed or support devices for the operation planned.

Never place your face or body in line with the cutting tool.

Never place your fingers or hands in path of saw blade or
other cutting tool.

For rip or rip-type cuts, the following end of a workpiece to
which a push stick or push board is applied must be
square (perpendicular to the fence) in order that feed
pressure applied to the workpiece by the push stick or
block does not cause the workpiece to come away from
the fence, and possibly cause a kickback.

•

During rip and rip-type cuts, workpiece must be held down
on table and against fence with a push stick, push block,
or featherboards, as applicable (see Figures la and l b,
page 4).

WARNING;
For your own safety, do not operate your saw until it
is completely assembled and installed according to instructions.
STABILITY

OF SAW

If there is any tendency for the saw to tip over or move during
certain cutting operations, such as cutting extremely heavy
panels or long heavy boards, the saw should be bolted down.
tf you attach any kind of extensions over 24" wide to either
end of the saw, make sure you either bolt the saw to the floor,
as appropriate, or support the outer end of the extension from
the bench or floor, as appropriate.

Push Stick: A safety device used to push the workpiece
through a cutting operation. Used most often when rip cutting
thin workpieces.

LOCATION

The push stick and push block examples shown below are useful for keeping hands and fingers away from saw blade during
ripping, rabbeting and dadoing. Apply downward pressure and
push workpiece through the cut and past the blades. Several
other configurations may be suitable for safe operation.

The saw should be positioned so neither the operator nor a
casual observer is forced to stand in line with the saw blade.

KICKBACKS
A kickback occursduringa rip-typeoperationwhen a part or
all of workpieceis thrownback violentlytowardoperator.
Keep yourface and bodyto one side of the saw blade, out of
linewith a possible kickback.
Kickbacksand possibleinjuryfrom them can usuallybe avoided by:
• Maintainingripfence parallel to saw blade.
° Keepingsaw bladesharp. Replace or sharpen anti-kickbackpawls when pointsbecome dull.
• Keepingsaw blade guard, spreader,and anti-kickback
pawls in place and operatingproperly.The spreader must
be in alignmentwiththe saw bladeand the pawls must
stop a kickbackonce it hasstarted. Checktheir action
beforeripping.
• Not ripping work that is twistedor warpedor does not
have a straight edge to guide alongthe rip fence.
•

Not releasing work until you have pushedit all the way
pastthe saw blade.

•
•

Usinga push stick for rippingwidthslessthan 6 inches.
Not confiningthe cutoffpiece when ripping or crosscutting.

Featherboards are used to keep the work in contact with the rip
fence or table during the cutting operation. Use of featherboards
can help to prevent kickbacks and binding. Featherboards
should be used for all "non thru-sawing" operations.

PROTECTION: EYES, HANDS, FACE, BODY, EARS
• If any part of yoursaw is missing, malfunctioning, or has
been damaged or broken (such as the motor switch, electroniccontrols,otheroperatingcontrol,a safety device or
powercord), cease operatingimmediately until the particular part is properly.repairedor replaced.
• Wear safety gogglesthat complywith UnitedStates ANSI
Z87.1 and a face shield or dust mask if operationis dusty.
Wear ear plugsor muffsduringextendedperiodsof operation.
•

Small loose pieces of wood or other objects that contact
the rear of the revolving blade can be thrown back at the
operator at excessive speed. This can usually be avoided
by keeping the guard and spreader in place for all thrusawing operations (sawing entirely thru work) and by
removing all loose pieces from the table with a long stick
of wood immediately after they are cut off.

•

Use extra caution when the guard assembly is removed for
resawing, dadoing, or rabbeting--replace
guard as soon
as that operation is completed.

•

Never reach in back of the cutting tool with either hand to
hold down or support the workpiece, remove wood scraps,
or for any other reason. Avoid awkward operations and
hand positions where a sudden slip could cause fingers or
hand to move into a saw blade or other cutting tool.

Do not perform layout, assembly, or setup work on the
table while the cutting tool is rotating.

•

Do not perform any operation freehand--always
use either
rip fence or miter gauge to position and guide the work.

Never use the rip fence when cross-cutting or the miter gauge
when ripping. Do not use rip fence as a length stop. Never
hold onto or touch free-end of workpiece or a free-piece that
is cut off, while power is ON and/or saw blade is rotating.

•

Shut the saw OFF and disconnect power source when
removing the table insert, changing the cutting tool,
removing or replacing the blade guard, or making adjustments.
Provide adequate support to the rear and sides of the saw
table for wide or long workpieces.

Plastic and composition materials (like hardboard) may be
cut on your saw. However, since these are usually quite
hard and slippery, the anti-kickback pawls may not stop a
kickback. Therefore, be especially attentive to following
proper setup and cutting procedures for ripping. Do not
stand, or permit anyone else to stand, in line with a potential kickback.
If you stall or jam the saw blade in the workpiece, turn saw
OFF and remove the workpiece from the saw blade.
Check to see if the saw blade is parallel to the miter
gauge grooves and if the spreader is in proper alignment
with the saw blade. If ripping at the time, check to see if
the rip fence is parallel with the saw blade. Readjust as
required.

Donotremove
smallpieces
ofcutoffmaterial
thatmay
become
trapped
inside
thebladeguardwhilethesawis
running.
Thiscouldendanger
yourhands
orcausekickback.
TurnsawOFFandwaituntilbladestops.
Useextracarewhenripping
woodwithtwisted
grainor
woodthatistwisted
orbowed--it
mayrockontableand
pinchsawblade.

24"

5" Long (typ.)
.
5/_6tt

/ °77 i

i__

(typ.)J

Solid Lumber

IIit1IIIIIII1|111111IIII

Clamp to rip fence or
rip fence extension to
keep work on the
table.

12" _

rip Fence

........

Table

11/2 t_

i • fI

6½"

Blade
Miter slot

._-1¾"

) to table
to guide work

#
5"

Use featherboards
workpieces.

in combinations

as required

to control

Figure lb - Fealherboards

USE ONLY ACCESSORIES
•

°
Figure la - Example: Push Sticks and Push Blocks
KNOW YOUR
•

CUTTING

TOOLS

Dull, gummy, improperly sharpened or set cutting tools can
cause material to stick, jam, stall saw, or kickback at operator. Minimize potential injury by proper care and machine
maintenance.

•

Do not use any blade or othercuttingtool marked for operating speed less than 3800 RPM. Never use a cuttingtool
larger in diameter than diameter for whichsaw was
designed.For greatestsafetyand efficiencywhen ripping,
use maximum diameter blade for whichsaw is designed,
since underthese conditionsspreader is nearest the
blade.

Adjust table insertsflush withtable top. Never operate saw
unlessproperinsertis installed.

WARNING:
Never attempt to free a stalled saw blade without first turning saw OFR
•

Never use grinding wheels, abrasive cutoff wheels, friction
wheels (metal slitting blades), wire wheels or buffing
wheels.

DESIGNED FOR SAW

Crosscutting operationsare workedmore convenientlyand
with greatersafety if an auxiliarywoodfacing is attached
to miter gauge usingholesprovided. However, facing must
not interferewith properfunctioning of saw blade guard.
Make su£e the top of the arbor or cuttingtool rotates
towardyou when standingin normaloperatingposition.
Also make sure the cuttingtool, bladeflange and arbor
nut are installedproperly. Keep the cuttingtool as low as
possiblefor the operationbeing performed. Keep all
guards in place wheneverpossible.

•

Never feed materiaI into the cutting tool from the rear of
the saw. An accident and serious injury could result.

Hardware Bag #2
M8 x 28 Hex Head Bolt (8)
M8 x 25 Hex Head Bolt (8)

THINK SAFETY

M8
M8
M8
M8
M8

Safety is a combinationof operatorcommonsense and alertness at all times when the saw is being used.
Never use another personas a substitutefor a table extension, or as additionalsupportfor a workpiecethat is longeror
widerthan basic saw table,or to assistin feeding, supporting
or pullingthe workpiece.

Hardware Bag #3
M6 x 16 Hex Head Screw (2)
M6 Flat Washer (2)
M6 Hex Nut (2)
M6 Lock Washer (2)

Do not pullthe workpiecethroughthe saw blade--position
your bodyat the infeedside of the guard;start and complete
the cutfrom that same side. This wil] require addedtable supportfor long or wide workpiecesthatextendbeyond the
lengthor widthof the saw table.
CAUTION: Followsafety instructions
that appear on the front
of your saw.

Hardware Bag #4
MIO x 25 Socket Head Bolt (4)
M8 x 16 Socket Pan Head Screw (8)
M6 x 12 Socket Pan Head Screw (24)
M6 x 16 Socket Head Bolt (2)
M5 x 12 Socket Head Bolt (4)
M3 x 10 Pan Head Screw (4)

Refer to Figure 2.
•

•

Open shipping box. Remove all parts, except saw body,
from both styrofoam packing bases and set parts and top
base safely aside.

M10 Lock Washer (4)
M6 Hex Nut (2)

Use utility knife to cut down the four corners of the shipping box, fulIy exposing the bottom packing base.

M5 Lock Washer (4)
M3 Lock Washer (4)
M10 Flat Washer (4)
M6 Flat Washer (2)
M5 Flat Washer (4)
M3 Flat Washer (4)

•

Cut away enough styrofoam from motor cover side of
packing base so that, with the aid of an assistant, you can
slide the saw body from the base.
CAUTION; Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.

Hardware
10/13mm
4ram Hex
5mm Hex
8mm Hex

Check for shipping damage or missing parts. If any parts are
damaged or missing, call 1-800-266-9079 for replacement.
The table saw body comes assembled as one unit. Additional
parts which need to be fastened to the saw should be located
and accounted for before assembling:
A
B

Extension Table (2)
Dust Chute

C
D

Front Rail (2)
Rear Rail (2)

E
F
G
H

Miter Gauge Assembly
Blade Guard Assembly
Caster Set (2)
Table Insert

I
J
K

Handwheel Assembly with Knob (2)
Rip Fence Assembly
Rubber Foot (4)

L
M
N

Anti-kickback Pawl Assembly
Line Cord Hooks (2)
Brace

O
P

Rip Fence Storage Hooks (2)
Blade Guard Storage Hooks (2)

Q
R

Push Stick Storage Hooks (2)
Push Stick

S
T

Base Panel (4)
Corner Support (4)

x 20 Hex Head Bolt (4)
Lock Washer (20)
Flat Washer (20)
Hex Nut (16)
Acorn Hex Nut (4)

Bag #5
Open End Wrench
Wrench
Wrench
Wrench

•

T7"

Hardware Bag #1
M10 x 25 Socket Head Bolt (6)
M10 Lock Washer (6)
M10 Fiat Washer (6)
Figure 2 - Unpacking

o
o

IMPORTANT: Table is coated with a protectant. To ensure
proper fit and operation, remove coating. Coating is easily
removed with mild solvents, such as mineral spirits, and a soft
cloth. Avoid getting solution on paint or any of the rubber or
plastic parts. Solvents may deteriorate these finishes. Use
soap and water on paint, plastic or rubber components. After
cleaning, cover all exposed surfaces with a light coating of oil.
Paste wax is recommended for table top.
WARNING;
Never use highly volatile solvents. Non flammable solvents are recommended to avoid possibte fire hazard.

Refer to Figures 3-34.
CAUTION: Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.

Figure 4
ASSEMBLE

Be certain all parts are clean and free of shipping preservative. Also, completely remove all parts of packing. Saw cabinet
should be directly on the floor.
SAW

Hardware Required: Twenty-four M6 x 12 socket pan head
bolts (Hardware bag #4).

•

the power source.
INSTALL HANDWHEELS
Refer to Figure 3.

•

Place one of the handwheels onto the blade raise!lower

•
•

PANELS

Tools Required: 4ram Hex Wrench

Positioning the saw on a level surface will improve stability
and accuracy and prevent warpage and failure of cast
components and welds.
WARNING:
Make certain that the saw is disconnected from

Remove saw cabinet and place upside down on cardboard
box or cardboard on floor.

BASE

Refer to Figures 5 and 6, pages 6 and 7.

INSTALLATION

•

MOBILE

NOTE: Finger tighten bolts and nuts until caster sets are
assembled to base panels (Figure 12, page 7). Then tighten all fasteners securely.
Attach the front panel between two corner supports using
six M6 x 12 socket pan head screws.
NOTE: Place the paneI edges INSIDE the corner support
surfaces.
NOTE: Front panel and rear panel are both stamped 'A'.
Front panel has warning label.
Repeat above step for the rear panel

shaft located on the front of the cabinet. Align the groove
in the back of the handwheel with the pin.
Thread the washer and ]ocking knob onto the threaded end
of the shaft.

Letter Stamp On Top Edge

Repeat the steps above to assemble the remaining handwheel and locking knob onto the blade tilt shaft located on
the side of the cabinet.

Figure 5....

•
•
-_
•

REMOVE PACKING MATERIAL
Refer to Figure4.
•

Use the bladetilt handwheel to tilt the motorcompletelyto
45°.

•

Removethe packing material from behindthe motor.

•

Return motorto the 0° position.

Turn all panels upside down to perform base assembly.
Attach one corner of left panel (stamped 'B') to front panel
A.
Attach the other corner of left panel B to rear panel A.
Repeat above two steps for attachment
(stamped 'C').

of right panel

Below is completed base assembly.

•

The kick plate cam must be underneath the caster to function properly (see Figure 10).

A
C

Figure 10
•
A
=
ASSEMBLE

CASTER

Refer to Figures 10 and 11; place caster onto the bracket
and secure in position with bolt and hex nut.
Repeat above steps for the second caster set.

SETS

Refer to Figures 7-11.
Tools Required: Two _" Open End Wrenches
Refer to Figure 7; remove casters (4) and supports (2)
from carton.

Figure11
Figure 7
*

Loosen and remove the bolt and hex nut from the bracket
(see Figure 8)

ATTACH CASTER SETS TO BASE
Refer to Figure 12.
Tools Required:5ram HexWrench
Hardware Required: EightM8 x 16 socket pan head screws
(Hardwarebag #4).
• Attach one caster set to the two front corner supports
using four M8 x 16 socketpan head screws.
• Attach the remaining caster set to the two rear corner
supports.

Figure 8
•

Rotate foot pedal bar so that kick plate cam is inside
bracket (see Figure 9).

Figure 9 - Kick Plate Cams Inside the Brackets

Figure 12

ATTACH

CORD WRAP

HOOKS

Refer to Figure 13.
Tools Required: 4mm Hex Wrench
Hardware Required: Two M6 x 16 socket pan head bolts, two
M6 flat washers and two M6 hex nuts (Hardware bag #4).
•

Insert a bolt into a cord wrap hook and place against the
holes on the left side of the saw cabinet.

Secure hook in position using flat washer and hex nut.

Repeat for other hook.

Figure 15

ATTACH RIP FENCE BRACKETS
Refer to Figure 16.
Tools Required: 5mm Hex Wrench
Hardware Required: Two M6 x 16 socket head bolts, two M6
flat washers and two M6 hex nuts (Hardware bag #4).
°

Install the rip fence storage brackets to the right side panel
of the base using two bolts, fiat washers and hex nuts.

Figure 13
ATTACH

BASE TO CABINET

Refer to Figures 14 and 15.
Tools Required: 8mm Hex Wrench
Hardware Required: Four Mt0 x 25 socket head bolts,four M10
lock washers and four M10 flat washers (Hardware bag #4).
• Place dust chute over the cabinet as shown. Make sure
the holes in the corners are aligned with the slots in the
dust chute.

Figure 16
BLADE GUARD
BRACKETS

AND PUSH

STICK

STORAGE

Refer to Figure 17, page 9.
Tools Required: Phillips screwdriver

and 4ram hex wrench

Hardware Required: Four M3 x 10 pan head screws, four M3
lock washers, four M3 flat washers, four M5 x 12 socket head
bolts, four M5 lock washers and four M5 fiat washers
(Hardware bag #4).
•

Install the push stick storage brackets to the left side panel
of the base using four screws, lock washers and flat
washers.

•

Install the blade guard storage brackets to the ]eft side
panel of the base using four screws, lock washers and flat
washers.
NOTE: Attach the slotted bracket to the front side of the saw.

Figure 14
•

•

Place the base assembly over the dust chute and secure
the base assembly to the cabinet using the flat washers,
lock washers and bolts.

•

Press the four rubber feet to the base legs.

•

With the aid of an assistant turn the saw upright.

WARNING: To avoid injury, Do Not attempt to turn saw
upright by yourself.

Secure all fasteners in the base assembly fully tight.

Rubber Feet

Slotted Bracket

Figure19
Figure 17

ATTACH EXTENSION TABLES
•

Referto Figure I8.
ToolsRequired:8ram HexWrench and StraightEdge
Hardware Required:Six M10 x 25 sockethead bolts,six M10
lockwashers and six MI0 flat washers (Hardware bag #1).

Place blade on arbor. Make sure arrow on blade and teeth
point towards front of saw.
Replace flange and nut on arbor and securely snug blade
in position.

• Assemble extension table to the table usingsockethead
bolts,lock washersand flat washers.
•

Wipe surfaceclean.

•

Hand tightenonly.Do not tightencompletelyuntil tables
are level. Use a straightedge to level tables.
Repeat above procedure for the other extensiontable.

°
°

Use a straight edge to checklevel and flatnessbetween
main and extension tables.

After tables are adjusted level and flat, secure the extension tables by tightening the bolts completely.

Figure 20

CHECK TABLE ALIGNMENT
Refer to Figures 21, 22 and 23, page 10. _.•

•

Figure 18

INSTALL BLADE

•

Refer to Figures19 and 20.
Tools Required:13ram Open end Wrench
-

Loosen knob on right side of cabinet.

•
•

Remove blade and wrench. Replace knob.
Raise blade assembly all the way up.

•

Depress arbor lock and use wrench to loosen flange nut.
Remove flange and nut from arbor.

Saws are shipped from the factory with the table adjusted
so the miter gaugeslotsare parallel to the saw blade.
However,in orderto obtainthe best resultsfrom the saw, it
is suggested this adjustmentbe checkedbeforeoperating.
A simple method of checkingalignment isas follows: Bolt
or clamp a dowelrod or similar objectto mitergauge (a
combinationsquarecan be substituted). Pick out a tooth
on front of bla_leand set the dowel to it so it isjust touching.Move same toothto backof blade.
Gauge thistoothwith the dowel rod. If the tooth is in the
same position,relative to the miter gauge slot, the table is
paral]elwith the blade. In short, the miter gauge slots must
be parallelwith the blade. This means that when measuring distancebetween blade and miter gauge slot at the
front and rear of the blade, the distanceswillbe equal
(see Figure21).
NOTE: Be sure to measure the distance or make the test
on the same toothof the saw blade in both front and rear
positions.

If an adjustment is necessary, proceed as follows: Loosen
and remove the six socket pan head screws and the rear
panel (see Figure 22). Loosen the three hex head bolts on
the trunnion (see Figure 23) and shift trunnions until a
position is found where the saw blade is parallel to the
miter guage slots.
NOTE: Saw blade should also be centered within its table
insert opening.
'r_l Rear

Saw

NOTE: If you perform this adjustment, leave the back panel off
to perform rear rail assembly as described in the next section.

RAIL ASSEMBLY
Refer to Figures24-29.
ToolsRequired:13ramOpen end Wrench
HardwareRequired: EightM8 x 28 hex head bolts, eight M8 x
25 hex head bolts,four M8 x 20 hex head bolts, twenty M8
lockwashers,twentyM8 flat washers,sixteen M8 hex nuts
and four M8 acorn nuts.(Hardwarebag #2).
• insert two M8 x 28 he)( head botts and two M8 x 25 hex
head boltsinto the T-slotof the right front guide rail.(The
two longerboltswillattach to the table;the two shorter
bolts attachto the table extension.)
• Attach rightfront railto the table and right table extension
using flat washers,lockwashersand hex nuts.
NOTE: Hand tightenall hardwareduring rail assembly.Do not
completelytightenhardwareuntil ail railsare mounted.

.Blade }
I

i
I

i
L. ........

Attach leftfront rail in the same manner.(The two longer
bolts attachto the table;the two shorter bolts attach to
table extension.)
NOTE: You may have to shiftrightrail as far rightas it will go
to attach left rail.

1._1

-N-

Tighten the hex head bolts and lock washers very securely.
This procedure will set the table and blade in parallel position and prevent the trunnion from shifting.

-@Front
_"Miter Gauge Slots f

Figure 21 - Aligning Miter Blots to Blade

Figure 24 - Right Front Rail
,

Position rails so that rails are butted together and the joint
between rails is aligned with right side of the blade. You
may need a mallet to lightly tap rails together. Make sure
rails are completely butted together at the joint.
Use a straight edge as shown to check level and flatness
between right and left rail. Use a combination square as
shown to make certain that both front rails are parallel to
the table surface.

•

After front rails are adjusted leveI and flat, tighten the
screws completely.

Secure all hardware completely.

Figure 22 - Remove Rear Panel

Figure 25 - Use Straight Edge to Align Rail Joint to Blade

Figure 23 - Adjust Trunnions to Align Blade and Miter Slot

i!:_i:

IiZZLIIL i:.........
..................
ii ii :_

'_•

Figure 29
ATTACH

SWITCH

ASSEMBLY

Refer to Figure 30.
Tools Required: 10mm Open end Wrench

Figure 26 - Check parallelism of rails to table with combination
square. Check at several locations along rail.

Hardware Required: Two M6 x I6 hex head bolts, two M6 flat
washers, two M6 lock washers and two M6 hex nuts.
(Hardware bag #3).

Loosen and remove six socket pan head screws and the
back panel, This will allow easier attachment of the rear rails.

•

From above switch assembly bracket, insert two bolts
through bracket holes.
Loosely attach flat washer, lock washer and nut to bolts.
Insert bolt heads into T-slot on bottom of left front rail.

°
•
•

Slide switch assembly 6" to 8" from left end of rail as
shown in Figure 30.
Fully tighten flat washers, lock washers and hex nuts to
secure switch assembly in place.

•

Figure 27
• Install the rear rails in the same manner as the front rails
and align the rail joint to the blade,
•

Replace back panel of the cabinet.

Figure 30

POSITION

AND ADJUST

RIVING

KNIFE

Refer to Figure 31.
•
°

Riving knife is installed on the saw. Raise the blade completely to access the riving knife.
Loosen the locking knob and raise the riving knife to its
highest position. Riving knife has three holes for three positions. The highest position is for all thru cuts, The middle
position is for rabbets and other non-thru cuts, _(with guard
and pawls removed). The lowest position is for dado cuts.

Figure 28
•

Insert M8 x 20 hex bolts through holes in bracket at each
end of brace. Attach brace to the far right end of the rails
by sliding hex bolts into the rail T-slots. Secure bolts in
position with fiat washers, lock washers and nuts.

Bracket
Figure 31 - Riving Knife

•
°

Make sure locking pin is aligned with riving knife ho]e and
secure in position by tightening locking knob.

Blade Guard

Pawl Set

Riving knife must be in line with blade. Make sure riving
knife sits flat against mounting bracket and lock plate.

RIVING KNIFE TO BLADE ADJUSTMENT
•

Riving knife to blade clearance: the gap between the riving
knife and the saw blade should be an even distance
across the entire radius.

•

The riving knife should also be in line with the saw blade. If
adjustment is necessary:
1. Locate the riving knife bracket.
2. Loosen the two socket head cap screws slightly enough
to move the bracket, bringing the riving knife in line with
the saw blade. Make sure the gap between the blade
and knife is even and from ¼ to _" in distance.
3. Once the riving knife is aligned with the blade, tighten
the socket head cap screws.

INSTALL

TABLE

Figure 33 - Blade Guard and Pawl Attachment

INSERT

Refer to Figure 32.
°
•

Make sure that the riving knife is raised to its highest
position.
Place table insert into throat of table.

•

Insert is held in position by magnet in table.

To adjust insert level with table, adjust leveling screws up
or down.

Figure 34

Figure 32

ATTACH BLADE GUARD AND ANTI-KICKBACK
PAWLS
Insert Bolt Here

Refer to Figures 33-36, page 12 and 13.
•

Place the slot of blade guard body over the riving knife.
Slot of bushing is placed in the notch indicated in Figures
33 and 34.

The bushings have a beveled edge and must be located in
the center of the notch to lock properly.

Position guard completely down on riving knife and press
latch to lock in position.

Blade guard body should be parallel to the table, if not,
adjust the 2mm set screws as necessary.

Place anti-kickback pawl set onto riving knife at notches
indicated. The spring pin is placed in the front notch and
bolt is placed in the rear notch.

•

Press pawl set completely down and press latch to secure
in position.

Figure 35 - Attach Paw! Assembly

NOTE: The teeth of anti-kickback pawls should touch table
surface. Use set screws to adjust if needed.

INSTALL

RIP FENCE

Refer to Figure 39.
•

Position rip fence assembly at end of saw. Be certain locking lever is in UP unlocked position.

Place rip fence assembly onto rails, positioning clamp over
rear rail and then placing rip fence onto front guide rail.

•

Rip fence should now ride freely on rip fence rails. Once
rip fence is completely installed, it should be parallel with
the miter gauge and perpendicular to the table. If not, refer
to "Rip Fence Adjustment" in the Operation section of this
manual.

Figure 36 - Latches Lock and Unlock Blade Guard and Pawls
to Riving knife
INSTALL

MITER

GAUGE

Refer to Figure 37.
•

The miter gauge comes preassembled. Unpack the miter
gauge and clean thoroughly. Insert into storage slots on
right side of cabinet.

Figure 39

GROUNDING

INSTRUCTIONS

WARNING:
Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electrical shock.
•

This too] is equipped with an approved 3-conductor cord
rated at 300V and a 3-prong grounding type plug (see Figure
40) for your protection against shock hazards.

Figure 37

INSTALL PUSH STICK

Grounding plug should be plugged directly into a properly
installed and grounded 3-prong grounding-type receptacle,
as shown (Figure 40).

Refer to Figure38.
•

Check with a qualified electrician if grounding instructions
are not understood or if in doubt as to whether the tool is
properly grounded.

Insertthe pushstickintobracketson leftside of base.

PG PoeudnYd
1_g; rnode_0 utlet.,. \ _iP{'P"--_ --_-':'_

3-P,ono
P,uo ....
Figure 40 - 3-Prong Receptacle

•

Do not remove or alter grounding prong in any manner. In
the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical shock.

WARNING:
Do not permit fingers to touch the terminals of
plug when installing or removing from outlet.
°

Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes and
ordinances. Do not modify plug provided. If it will not fit in
outlet, have proper outlet installed by a qualified electrician.

•

Inspect tool cords periodically and if damaged, have them
repaired by an authorized service facility.

•

Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric cord
or plug is necessary, do not connect the green (or green
and yellow) wire to a live terminal.

•

Where a 2-prong wall receptacle is encountered, it must be
replaced with a properly grounded 3-prong receptacle
installed in accordance with National Electric Code and
local codes and ordinances.

WARNING:
electrician.

NOTE: Using extension cords over 300 ft. long is not
recommended.

ELECTRICAL CONNECTIONS
WARNING: Make sure unit is off and disconnected from
powersource beforeinspectingany wiring.
The saw isprewiredfor use on a 120 volt,60HZ powersupply.
The power linesare inserteddirectlyontothe switch. The
green groundlinemustremainsecurely fastened to the frame
to properlyprotect againstelectrical shock.
240 VOLT OPERATION

This work should be performed by a qualified

A temporary 3-prong to 2-prong grounding adapter (see
Figure 41) is available for connecting plugs to a two pole outlet if it is properly grounded.
Grounding
Make Sure
This Is
Ad_
Connected To
3-Prong Plug

•

To use the saw with a 240V, single-phase power supply,
have a qualified electrician attach a 240 volt, 15A 3-prong
plug onto saw line cord and install the proper connectors
and receptacles to power supply.

•

See wiring diagram (Figure 42) for wiring instructions.
(

A Known
Ground

(

)

L1
2-Prong Receptacle
Figure 41 - 2-Prong Receptacle with Adapter
•

Do not use a 3-prong to 2-prong grounding adapter unless
permitted by local and national codes and ordinances.

•

(A 3-prong to 2-prong grounding adapter is not permitted
in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected
to a permanent electrical ground such as a properly
grounded water pipe, a properly grounded outlet box or a
properly grounded wire system.

•

(

120V

)

L1
Figure 42 -Wiring

(

;

)

(

240V

)

1.2

Schematic

Many cover plate screws, water pipes and outlet boxes are
not properly grounded. To ensure proper ground, grounding
means must be tested by a qualified electrician.
Refer to Figures 43-52, pages 15-18.

EXTENSION
•
°

CORDS
DESCRIPTION
The Craftsman 10" Model Number 218331 contractor saw
offers precise cutting performance for all woods up to 31,_"
thick. The saw is designed for the professional user and is
ruggedly constructed for continuous service. The 10" Saw is
recommended for use with a 10" blade.

The use of any extension cord will cause some drop in
voltage and loss of power.
Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.

•

Use the table to determine the minimum wire size (A.W.G.)
extension cord.

•

Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.

tf the extension cord is worn, cut, or damaged in any way,
replace it immediately.

Extension Cord Length (120V Operation)

The saw features an extra large cast iron table. Saw body has
on board storage for push stick, miter gauge, rip fence and
saw blades. Saw is equipped with a riving knife and a clear
acrylic blade guard with anti-kickback feature. Cabinet is constructed of heavy gauge welded steel, totally enclosed and is
ported for a 4" vacuum hose.

:.
Wire Size A.W.G.

Up to 25 ft .......................................

Up to 50 ft.......................................

Rip Fence Assembly features a heavy-duty precision rip fence
that is designed for simple and one-hand maneuverability.
Front rail is calibrated in inches and millimeters with a magnified window for close tolerances.

NOTE: Using extension cords over 50 ft. long is not
recommended.

SPECIFICATIONS

Extension Cord Length (240V Operation)

Capacity

Depth of cut at 90 ° . ..............................
Maximum tilt angle of arbor (left) ....................

Wire Size A.W.G.
Up to 50 ft .......................................
50 to 100 ft.......................................

18
16

100 to 200 ft......................................

200 to 300 ft......................................

with 10" Blade:

3%"
45 °

Depth of cut at 45 ° . .............................
Max. cut right of blade with rip fence .................

23/_"
30"

Max. cut left of blade with rip fence ..................

13"

Saw Dimensions:
Table height ...................................
Cabinet depth ...................................
Cabinet width ..................................
Table area ..............................
Front of table to blade ...........................

The saw can be locked from unauthorized use by locking the
switch. To lock the switch:

37_"
22"
19½"

°
°

26_6 x 20_6"
1I¾"

Rip Fence Dimensions:
Rip fence .....................................

31¼"

Rip fence rails (front and rear) .....................
Blade capacity maximum ..........................
Blade arbor .....................................

56_"
10"
%"

Dado blade capacity maximum .....................

'_,_"

NOTE: Should the key be removed from the switch at the ON
position, the switch can be turned off but cannot be turned on
again.
• To replace key, slide key into the slot on switch until it
snaps.
WARNING:
For your own safety, lower blade or cutting tool
below table surface. If blade is tilted, return it to vertical position. Turn off safety disconnect or circuit breaker when saw is
not in use.

Saw Constructions:
Cabinet ....................
Table .....................................

Totally enclosed steel panel
Cast iron

Rip fence .............................

Aluminum tube

Drive system ..................................
Exhaust port ................................
Miter gauge ..............
Blade guard ..............
Switch ...............

Turn the switch to OFF position and disconnect saw from
power source.
Pull the key out.The switch cannot be turned on with the
key removed.

V-belt
4" Male

Cast iron with T-slot roller guide
Acrylic with anti-kickback pawls
Locking paddle switch with overload

Arbor R.P.M.........................
Motor: .................

3550 RPM approx.
1¾HP,3550 RPM, capacitor start,

capacitor run, 120/240V, 15/7.5A,
single-phase, bail bearing
Gross weight with motor .......................
288 Ibs
BLADE
WARNING:
Disconnect power before attempting any of the
following procedures. Be certain switch is in OFF position and
safety disconnect (or breaker) is in OFF or open position. Saw
blade must not be moving. Saw blade will rotate freely after
motor is turned off. Altow blade to come to a complete stop
before attempting any of the following procedures.

•
•

Blade height is controlled by handwheel on the front of the
saw.

•

To adjust height, loosen locking hand knob. Rotate knob
counterclockwise approximately three turns. Turn handwheel to desired blade height.

CAUTION: For safety, blade should be raised only 1/8"above
the surface of the material to be cut. However, if hollow
ground blades are used, raise blade to its maximum height to
allow for greater blade clearance.
°

Lock blade height into position. Lock handwheel by tightening locking knob clockwise. Tighten only until snug.
IMPORTANT: Do not over tighten. Only a small amount of
pressure is necessary to lock handwheel securely.

STARTING AND STOPPING THE SAW
Refer to Figure 43.
WARNING: Never operatesaw withoutblade guardsin
place. Be sure blade is not in contactwith workpiecewhen
motor is started. Start motor and allowsaw to cometo full
speed.
WARNING: Make sure the electricalcharacteristicsof motor
nameplateand powersoume are the same.
• The ON/OFF switchis located underthe front rail ofthe
table saw at the left side.

ADJUSTMENT

Refer to Figure 44.

WARNING:
The operation of any power tool can result in
foreign objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying
with United States ANSI Z87.1 before commencing power tool
operation.

•

HEIGHT

To turn saw on, stand to eitherside of the blade---never in
line with it. Raise large red OFF paddle and pull up
ON/OFF switch. Always allow saw blade to come up to full
speed before cutting.
Do not turn motorswitch ON and OFF rapidly.This action
overheatsthe motorand may causesaw bladeto loosen.
Never leave saw whilethe power is on.

Figure 44 - Blade Height Adjustment

To turn the table saw off, pressthe large red OFF paddle.
Never leave saw until cuttingtool has cometo a complete
stop.

BLADE TILT ADJUSTMENT

45 ° STOP ADJUSTMENT

Refer to Figures 44 and 45, page 15 and 16.

Refer to Figure 46.

•

Tilt the saw blade to 45 °. Using a combinationsquare,
checkto see if blade is 45° to the table.

•

If the bladewillnot tiltto 45°, turn (counterclockwise) the
set screw locatedat the rightof the table insert, untilthe
blade can be positionedto 45°.
With the blade at 45°, tightenthe bevel handwheel lock
knob to keepthe blade from further tilting.
Turnthe set screwclockwiseuntilit comesin contactwith
the positivestop.

•

The saw blade can be set at any angle between 90 ° and
45 °. Blade tilt is controlled by the handwheel (Fig. 44) on
the right side of the saw. The indicator (Fig. 45) on front of
saw shows the tilt angle of the blade.
To adjust tilt, loosen locking hand knob. Rotate knob counterclockwise at least three turns. Turn handwheel to
desired blade angle. Lock blade angle into position.

•

Lock handwheel by tightening locking hand knob clockwise. Tighten only until snug.

•

= The saw is equipped with positive stops at 90° and 45 °.
These positive stops aUow operator to position saw blade
at 90 ° and 45 ° quickly and accurately.

TABLE

INSERT

ADJUSTMENT

Refer to Figure 46.
°
°

The table insert must always be level with the saw table.
Place a straight edge across the front and rear of the table
insert. Check that the insert is perfectly level with the saw
table.

•

To level the table insert, turn one or more adjusting set
screws as needed and recheck.

The table insert is equipped with two finger holes for easy
removal.

MITER

GAUGE

ADJUSTMENT

Figure 45 - Blade Tilt Handwheel

Refer to Figures 47 and 48, Pages 16 and 17.

90 ° STOP

ADJUSTMENT

Refer to Figures 44 and 46.
•

•

Raise saw blade above table as far as possible. Set blade
at 90 ° to table by turning the tilting handwheel. Place a
square on table and check to see if blade is perpendicular
to the table. When checking put square flush against saw
blade. Do not put square on teeth of saw blade.

Adjustment to index stops can be made by loosening locking nut and tightening or loosening three adjusting screws.
Be sure to tighten locking nut after adjustment is made.

If the blade will not tilt to 90 °, turn (counterclockwise) the
set screw at the left front of the table insert until the blade
can be positioned to 90 ° .

•

Once the blade has been tilted to 90 ° (confirm this using
your square), tighten the bevel handwheel lock knob,
located on the side of the cabinet. This will keep the blade
from tilting further.

•

Turn the set screw (clockwise) until it comes in contact
with the positive stop.

•

Check tilt indicator pointer. If necessary, adjust pointer so it
points to 0° mark on scale. To adjust pointer, remove
handwheel and loosen screw on pointer. Be sure to tighten screw securely after adjustment is completed.

Miter gauge supplied with saw is equipped with individually
adjustable index stops at 0° and 45 °, right and left, and
can be manually adjusted up to 60 ° right and left.

•

Face of miter gauge has two holes for purpose of attaching auxiliary facing.

•

Miter gauge is accurately constructed for precision work.
Miter gauge is guided through T-slot with a roller guide
mounted at front of guide bar. Roller guide adds to miter
gauge's stability and prevents the guide bar from leaving
T-slot.

•

To operate miter gauge, simply loosen locking knob and
move miter gauge to desired angle. The miter gauge will
stop at 0° and 45 °, both right and left. To position miter
gauge past these points, simply pull out gauge stop.
Position miter gauge at desired angle and tighten locking
knob.

•

Be positive the edge of workpiece next to face of miter
gauge is straight and tight against miter gauge so that the
workpiece does not rock or rotate. Always use both hands
when operating the miter gauge.

•

The miter gauge is used for cross-cutting, compound miter
cutting, miter cutting, rabbeting, bevel cutting and dadoing.

Index Stop Adjusting

Screws and Nuts

Figure 47 - Index Stops

Figure 46 - Table Insert

If an adjustment is necessary, unlock the fence and turn
either of the two adjusting screws.

NOTE: This is for micro-adjustment only. If fence cannot be
adjusted square, recheck rail adjustment.

Roller Guide

Lock fence in position and recheck. Continue this procedure until fence is square to the table.

PARALLEL
Locking

Miter Gauge

ADJUSTMENT

•

Position fence so that fence edge is aligned with slot edge.

•

Slot and fence edge should be paralIel.

•

If an adjustment is necessary, unlock the fence and turn
either of the two adjusting screws.

Lock fence in position and recheck. Continue this procedure until fence is square to the table.

Figure 48 - Miter Gauge Assembly
RIP FENCE

ADJUSTMENT

The saw's rip fence is precision manufactured, incorporating
fine adjustments for accurate cuts. The saw is built to allow
the operator to accurately adjust the rip fence without problems in a matter of seconds.
LEVELING

THE FENCE TO THE TABLE

•

Lift the lock handle to unlock the fence.

•

Observe the space between the fence bottom and the
table. The space should be equal along the entire length
of the fence.

•

If the space is not equal, the rails need to be adjusted so
that rails are at the same vertical position with respect to
the table. See Rail Assembly, pages 10-11.
Figure 50

SETTING CLAMPING PRESSURE

CURSOR

Refer to Figure 49.
Rip fence has been adjusted at the factory to locksecurely
when the lock handle is pusheddown. To adjust:
* Unlockfence and remove it from the rails.

Refer to Figure 51.
• Raise the saw blade above the table.
•

Position the fence several inches to the right of the saw
blade.

•

Lock the fence down and measure the exact distance
between the saw blade and the inside of the fence.

•

Loosen the two screws on the lens and slide it left or right
until the cursor (red line) equals the measurement
obtained in the previous step.

Adjust the hex nut untilthe fence is held securelywhen
the lock handle is pushed down,

ADJUSTMENT

Retighten the screws and make a test cut. Measure the
cut piece to verify that the cursor is set correctly.
NOTE: This adjustment should be checked whenever a new
blade is installed.

Hex Nut

SETTING FENCE PERPENDICULAR

AND PARALLEL

Refer to Figure 50.
PERPENDICULAR
ADJUSTMENT
• Position fence anywhere on table and lock it down.
°

g Lever

Place a square on the table next to the fence and check to
see that the fence is at 90 ° to the table.
Figure 51

RIP FENCE

OPERATION

•

Have blade extend approximately 1/_,above top of workpiece. Additional blade exposure increases hazard
potential.

•

Do not stand directly in front of blade in case of a kickback. Stand to either side of the blade.

•

Keep your hands clear of the blade and out of the path of
the blade.

•

If the blade stalls or stops while cutting, turn switch OFF
and safety disconnect OFF before attempting to free the
blade.

•

Do not reach over or behind the blade to pull the workpiece through the cut, to support long or heavy workpieces, to remove small cut-off pieces of material or for
any other reason.

•

Do not pick up small pieces of cut-off material from the
table. Remove them by pushing them off table with a long
stick. Otherwise they could be thrown back at you by the
rear of the blade.

•

Do not remove small pieces of cut-off material that may
become trapped inside blade guard while saw is on. This
could endanger your hands or cause a kickback. Turn saw
off. After blade has stopped turning, lift guard and remove
the piece.

•

Always lower blade below the table level when machine is
not in use.

Refer to Figure 51.
•

•

Unlock the fence by lifting the locking lever. Using the
scale for placement, position the rip fence. Lock the rip
fence into position by placing the locking lever in the down
position.
The rip fence is used for the following operations: ripping,
bevel ripping, ploughing, resawing, rabbeting and dadoing.

INSTALLING AND REMOVING THE RIVING KNIFE
Refer to Figure 52.
Install
•
•

•

Line up the riving knife in the proper direction to the
mounting bracket.
Push the riving knife all the way down into the mounting
bracket. Make sure the lock pin is locked in the hole of the
riving knife. (The lock hole is on the button side of the
riving knife).
If the riving knife is not locked properly, hold the locking
knob and pull the lock pin out; then re-insert the pin securely in the hole of the riving knife. While raising or lowering the
knife, pin will snap in the hole of the knife when located at
one of the three positions.
Tighten the locking knob.

Remove
• Loosen the locking knob.
• Hold the knob and pullthe lockingpin out.
• Removethe rivingknife outof the mountingbracket.
NOTE: Make sure bladeis at the highest position before
adding or removingthe rivingknife.

TYPES OF CUTS/OPERATIONS
THROUGH

CUTS

A through cut is a sawing operation in which the workpiece is
completely sawn through. Examples of through cuts are rip
cuts, cross cuts, miter cuts, and beveled cuts. The blade
guard assembly MUST be used when performing through
cuts.
CROSSCUTTING
WARNING:
Use caution when starting the cut to prevent
binding of the guard against the workpiece.
This cut is performed with the miter gauge set at "0", and is
used for cutting across the workpiece grain at 90 ° (blade
square with both the edge and flat side of wood).

Bracket

MITER CUTTING

Figure 52 - Riving Knife

WARNING:
Miter angles greater than 45" may force the
blade guard assembly into the saw blade causing damage to
the blade guard assembly and personal injury. Before starting
the motor, test the operation by feeding the workpiece into the
blade guard assembly. If the blade guard assembly contacts
the blade, place the workpiece under the blade guard assembly, not touching the blade, before starting the motor.

WARNING:
For your own safety, always observe the following safety precautions.
•

Never make any cut freehand (without using miter gauge
or rip fence). Blade can bind in the cut and cause a kickback.

•
•

Always lock miter gauge or rip fence securely when in use.
Remove rip fence from the table when miter gauge is in

WARNING:
Certain workpiece shapes, such as molding may
not lift the blade guard assembly properly. With the power off,
feed the workpiece slowly into the blade guard area and until
the workpiece touches the blade. If the blade guard assembly
contacts the blade, place the workpiece under the blade
guard assembly, not touching the blade, before starting the
motor.

use.

•

Remove miter gauge from table when rip fence is in use.

•

Make sure blade guard is installed for all "through sawing"
operations. Through sawing operations are those operations in which the saw blade cuts completely through the
thickness of the wood. Replace guard immediately after
completion of resawing, rabbeting and dadoing.

This cut is performed with the miter gauge, and is used for
cutting at an angle other than 90 ° square with the edge of the
workpiece.

Frequently check action of anti-kickback pawls by passing
the workpiece alongside the spreader while saw is off. Pull
the workpiece toward you. If the pawls do not dig into the
workpiece and hold it, the pawls must be sharpened. (See
Maintenance section, page 19.)

BEVEL CROSSCUTTING
WARNING: When possible, use the right miter gauge slot
when beveI crosscuttingso that the bladetilts away from the
miter gaugeand your hands.

DADOING
This cut is performed with either the miter gauge or rip fence.
Dadoing is done with a set of blades (dado set) rather than
standard saw blades. The dado set is used to groove wood
similar to ploughing and rabbeting. However, the dado set
allows operator to remove more material in one pass. The
operator, with a dado set, can Vary width of cut up to _0".

WARNING: Use cautionwhen startingthe cut to prevent
bindingof the guardagainstthe workpiece.
This cut is performedwiththe miter gauge,and is the same
as crosscutting,exceptthat the workpieceis also cut at an
angleotherthan 90 ° squareto the flat side of the wood(blade
is at an angle).

Instructions for operating dado set are contained in owner's
manual furnished with dado set. Dadoing requires cuts which
do not go all the way through material. Therefore, blade guard
must be removed. Dado sets have different characteristics
than saw blades. As a result, saw must be fitted with special
parts that are not furnished with saw (Dado Insert, Part No.
31158.00).
The maximum dado blade set that can be used on this saw is
%" I.D. x 8" O.D. x '_" Wide.

COMPOUND MITER CUTTING
Thiscut is performedwith the miter gauge, and is a combinationof miter cuttingand bevel crosscutting.
The cut is made at
angleotherthan 90° to both the edge and flat side of wood.
RIPPING

IMPORTANT: Always use correct insert. When using the
dado set, use caution. Use featherboards and push sticks as
applicable.

WARNING:
When bevel ripping and whenever possible,
place the fence on the side of the blade so that the blade is
tilted away from the fence and hands. Keep hands clear of the
blade and use a push stick to feed the workpiece if there is
less than 6" between the fence and the blade.

WARNING:
Always immediately replace the standard blade,
blade guard and blade insert when you are finished dadoing.

This cut is performed with the rip fence, and is used to cut the
workpiece lengthwise with the grain. Position the fence to the
desired width of rip and lock in piace. When ripping long
boards or large panels, always use a work support.

FREEHAND
Freehand is a very dangerous operation of making a cut without using the miter gauge or rip fence. Freehand cuts must
never be performed on a Table Saw.

BEVEL RIPPING

CUTTING

OVERSIZED

WORKPIECES

WARNING:
Before connecting the table saw to the power
source or operating the saw, always inspect the blade guard
assembly and riving knife for proper alignment and clearance
with saw blade. Check alignment after each change of bevel
angle.

When cutting long workpieces or large panels, always support
workpiece that is not on table. Use adjustable roller stand or
make simple support by clamping a piece of plywood to saw
horse. Add facings to miter gauge or rip fence as needed.

WARNING:
When possible, place the fence on the right side
of the blade so that the blade is tilted away from the fence
and hands. Keep your hands clear of the blade and use a
pushstick to feed the workpiece if there is less than 6"
between the fence and the blade.

DUST

IMPORTANT: Do not allow facings to interfere with operation
of blade guard.

This cut is performed with the rip fence, and is the same as
ripping, except that the blade is set at an angle other than 90 °.
RESAWlNG
This cut is performed with the rip fence, and is used to rip a
workpiece through its thickness rather than across its flat
width. Do not attempt to resaw bowed or warped material.

•

Saw is fitted with a 4" male exhaust port.

•

Before starting saw, see that all adjustments are properly
made and guards in place. With power disconnected, turn
pulley by hand to make sure everything is correct before
connecting power and starting saw.

BLADE SELECTION
Bladeselectionis based on type of materialbeing cut and
how it willbe cut.There are three genera] types of saw
blades:ripsaw bladescut with grain of wood, cut-offsaw
bladescutacross grain,and combinationsaw bladescutwith
grain,across grainand any angleto grain.

NOTE: It may be necessary to remove blade guard and use
work supports as weII as push blocks when performing this
operation.
WARNING:
Install blade guard immediately
of resawing operation.

COLLECTING

upon completion

Blades vary in many aspects.When selecting a blade, the followingbladecharacteristicsshould matchup with operationto
be performedand type of material to be cut:type of steel;
qualityof steeI; toothstyle; toothset; carbidetipped;grind;
number of teeth and size.

PLOUGHING
This cut is performed with the rip fence, and is used to make
a groove lengthwise with the grain of the workpiece. Use
proper hold downs and feed devices.

IMPORTANT:Your saw is only as accurate and efficientas
blade or cuttingtool used.
:
First,be certainto use the appropriatetype of cuttingtoolfor
the operationto be performed. Second, it is stronglyrecommendedthat high-quaIityblades and cuttingtoolsbe used.Be
certain blades and cuttingtools are kept sharp and in good
workingorder.Check blades periodically and replaceor
sharpen if necessary.

RABBETING
This cut is performed with either the miter gauge or rip fence.
Rabbeting is used to cut out a section of the corner of a
workpiece, across an end or along an edge. To make a rabbet
requires cuts which do not go all the way through the material. Therefore, blade guard must be removed. Install blade
guard immediately upon completion of rabbeting operation.
Rabbet cuts can also be made using dado head.

WARNING:
USE ONLY 10" diameter blades with %" arbor
holes, rated at or higher than 3800 R.RM.

WARNING: Do not attempt under any circumstances, to
service,repair,dismantle, or disassemble any mechanical
or electrical componentswithoutphysicallydisconnecting all
power soumes.

•
•

Remove blade guard assembly and pawl assembly.
Remove the table insert.

•

Unlock the raise!lower handwheel lock and raise saw
blade to maximum height.

Depress locking pin (see Figure 53) and slowly rotate
blade toward you until pin engages into arbor. Hold arbor
in locked position.

CLEANING
Clean off any preservative on bright (machined) parts with
appropriate solvent (mineral spirits). Avoid getting cleaning
fluid on any rubber parts as they tend to deteriorate
rubber.
•

Use soap and soft water on rubber and plastic parts.

After cleaning, lubricate unpainted surfaces with a light
application of medium consistency machine oil. This lubrication should be repeated at least once every six months.

NOTE: Instead of oil, a good quality paste wax can be applied
to rip fence and table surface. Paste wax will enhance movement of workpieces. In addition to providing lubrication, paste
wax will help prevent rusting.
=

•

Keep your machine and your workshop clean. Do not allow
sawdust to accumulate on saw or inside cabinet.
Frequently vacuum or blow out any sawdust that may
accumulate within cabinet.
Be certain motor and internal mechanisms are clean and
are frequently vacuumed or blown free of any dirt.

Figure 53 - Locking Pin Engages Arbor to Lock in Position
°

Place supplied open-end wrench (A) on the arbor nut (B).
Turn wrench counterclockwise to loosen nut. Remove

LUBRICATION
All bearings on the arbor are shielded ball bearings. These
bearings are permanently lubricated at the factory.
•

As needed, clean the grease off the rack and worm gears
of height and tilt mechanism. Lubricate rack and gears
with a medium viscosity machine oil.

•

Be sure to lubricate trunnion ways and all bushings.

•

Occasionally oil all other bearing points, including bIade
guard assembly, miter gauge and rip fence.

SERVICE
•

°
•

Replacebelts and worn parts as needed. If power cords
are worn, cut, or damaged in any way,havethem
replaced immediately.
Make sure teeth of anti-kickbackpawlsare always sharp.
Sharpen dull teeth usinga few lightstrokesof a smooth
cutflat file.

Figure54

arbor nut,blade flange (C) and saw blade (D).
Place new blade on arbor.Make sure saw blade teeth
point down at the front side of saw table.Place flange and
nut on arbor and securely snugblade in position.
Replacetable insert.

•

Replacebladeguard assembly and pawlassembly.

•

CHANGING THE SAW BLADE
Refer to Figures 53 and 54.
WARNING: Turn the power switch"OFF" and unplug the
powercordfrom its powersource when changingthe saw blade.
WARNING: When replaciqg blades, checkthe thickness
stamped ontothe rivingknife.You mustselect a bladewith a
kerf widthlargerthan the thicknessof the rivingknife.The kerf
widthshouldbe marked on the blade or blade package.
Thinnerblades may causethe workpieceto bind duringcutting.

Service Record
Craftsman 10" Contractor Table Saw

DATE

MAINTENANCE

PERFORMED

REPLACEMENT

PARTS REQUIRED

SYMPTOM

POSSIBLE

Saw stops or will not start

1. Overload tripped

Excessive vibration

CAUSE(S)

CORRECTIVE ACTION

2. Saw unplugged from wall or motor

1. Allow motor to cool ,and reset by
pushing reset switch
2. Check all plug connections

3. Fuse blown or circuit breaker tripped
4. Cord damaged
5. Defective capacitor

3. Replace fuse or reset circuit breaker
4. Replace cord
5. Replace capacitor

1. Stand on uneven floor

1. Reposition on flat, level surface
2. Replace saw bIade
3. Replace drive V-belts

2. Damaged saw blade
3. Bad drive V-belts
4. Bent pulley
5. Improper motor mounting
6. Loose hardware
7. Loose set screw in pulley

4.
5.
6.
7.

Cannot make square cut
when crosscutting

Miter gauge not adjusted properly

Adjust miter gauge

Blade stalls (however, motor turns)

1. Drive belts not tight

Adjust drive belt tension. Refer to Fig.
59, page 32. Loosen bolt (Key No. 1),
push motor down with pry bar and
tighten bolt to secure motor position.
2. Replace drive belts

Drive belts worn

Replace pulley
Check and adjust motor
Tighten hardware
Tighten set screw

Biade does not come up to speed

1. Extension cord too light or too long
2. Low shop voltage
3. Motor not wired for correct voltage

1. Replace with adequate size cord
2. Contact your local electric company
3. Refer to motor junction box

cut binds, burns or stalls when ripping

1. Dull blade with improper tooth set
2. Blade is binding at one end of cut
(heeling)

6. Excessive feed rate

1. Sharpen or replace blade
2. Adjust table and rip fence
parallel to blade
3. Make sure concave or hollow side is
facing down; feed slowly
4. Adjust rip fence
5. Adjust riving knife to fall in line with
blade
6. Reduce feed rate

Cut not true at 45 or 90 ° positions

Positive stops not properly adjusted

Adjust blade tilt

Tilt and elevating handwheet
difficult to turn

1. Sawdust on rack and worm gears

1. Clean and relubricate

2. Bushings and bearing surfaces dirty'

2. Clean thoroughly and lubricate

1. Guide rails or extension wing not
properly installed
2.
Guide of rip fence not adjusted
properly

1. Reassemble

Warped board

4. Rip fence not parallel to blade
5. Riving knife out of alignment

Rip fence binds on guide tube

guide rails

2. Adjust guides

Frequent Opening of fuses or
circuit breakers

1,
Motor overloaded
2. Fuses or circuit breakers do not have
sufficient capacity

1. Feed work slower into blade
2. Install proper size fuses or circuit
breakers

Material kicked back from blade

. Rip fence out of alignment
2. Riving knife not aligned with blade
3. Feeding stock without rip fence
4. Riving knife not in place
5. Dull blade
6. Letting go of material before it is past
blade

1. Align rip fence with miter slot
2. Align riving knife with blade

Anti-kickback

fingers dull

3. Always use rip fence or miter gauge
4. Install riving knife
5. Replace blade
6. Push material all the way past blade
before releasing work
7. Replace or sharpen anti-kickback
fingers

SYMPTOM

POSSIBLE

Saw makes unsatisfactory cut

1. Dull blade
2. Blade mountedbackwards

CAUSE(S)

3. Gum or pitchon blade
4. Incorrectblade for cut
5. Gum or pitchon table

Repair Protection Agreements
Congratulations on making a smart purchase. Your new
Craftsman ® product is designed and manufactured for years
of dependable operation. But like all products, it may require
repair from time to time. That's when having a Repair
Protection Agreement can save you money and aggravation.
Here's what the Repair
includes:

Protection

Agreement*

[]

Expert service by our 10,000 professional repair
specialists
I--4 Unlimited service and no charge for parts and labor on
all covered repairs
[] Product replacement up to $1500 if your covered product can't be fixed
[]

[]

Discount of 10% from regular price of service and related
installed parts not covered by the agreement; also, 10% off
regular price of preventive maintenance check
Fast help by phone -we call it Rapid Resolution phone support from a Sears representative. Think of us as
a "talking owner's manual"

Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service.
You can call anytime day or night, or schedule a service
appointment online.
The Repair Protection Agreement is a risk-free purchase. If you
cancel for any reason during the product warranty period, we
will provide a full refund. Or, a prorated refund anytime after
the product warranty period expires. Purchase your Repair
Protection Agreement today[
Some limitations
and exclusions apply. For prices and
additional information
in the U,S,A. call 1-800-827-6655,
*Coverage in Canada varies on some items. For full
details call Sears Canada at 1-800-361-6665.

Sears

Installation

Service

For Sears professional installation of home appliances,
garage door openers, water heaters, and other major home
items, in the U.S.A. or Canada call 1-800-4-MY-HOME®,

CORRECTIVE ACTION
1. Sharpenor replaceblade
2. Turn bladearound
3. Removeblade and clean
4. Change bladeto correcttype
5. Cleantable

Model 351.218331
Figure 55 - Replacement Parts Illustration for Rip Fence

10
11

KEY"'
NO,
1

PART NO,
09845.00

DESCRIPTION
3CMI-6 E-Ring

2
3

31107.00
31108.00

Locking Handle
8 x 50mm Spring Pin

4
5
6

31109.00
3I 110.00
3I 111.00

Bushing
Shaft
Cam

7
8

01923,00
31112.00

5 x 30mm Spring Pin
Adjusting Plate

9
10
I1

01203.00
31113.00
31114.00

12
13
14

31115.00
31116.00
31117.00

3CMI-5 E-Ring
Adjusting Plate
Adjusting Screw
Base

15
16
17

STD851004
06177.00
31118.00

I8
19
20
21

STD851008
STD852008
STD870820
311 I9.00

22
23

31120.00
31121.00

24
25
26
27

18782.00
STD863510
31122.00
31123.00

10 x 50mm Spring Pin
5-0.8 x 10mm Pan Head Screw*

28
29
30

STD851006
31124.00
00652.00

6mm Fiat Washer*

1
1
1
1

STD840610

Spring
6mm Flat Washer (W)
6-1.0mm Hex Nut*

1
1
1

QTY.
2
1
2
1
1
1
1
2
2
2
2
1

Nylon Screw
Lens
4mm Flat Washer*

2
2
2

4-0.7 x 8mm Flat Head Screw
Fence

2
1
2

8mm Flat Washer*
8mm Lock Washer*
8-1.25 x 20mm Socket Head Bolt*
3.5-1.3 x 10mm Threadforming
Cap
Latch

Screw

2
2
2
1
1
1

Clamp
Rod

Standard hardware item available locally.

Model 351.21 8331
Figure 56 - Replacement Parts Illustration for Cabinet

2O
13

KEY
NO.
1
2
3
4

PART NO.
31125.OO

DESCRIPTION
Scale

06346.00
31126.00
31135.00

6-1.0 x 12mm Socket Pan Head Screw
Front Corner Support

STD870820
STD852008

Left Rear Corner Support
8-1.25 x 20mm Socket Head Bolt*
8ram Lock Washer*

8
9

STD851008
31128.00
31129.00

8mm Flat Washer*
Strain Relief
Line Cord Hook

!0
11
12

09789.00
STD851006
STD843610

6-1.0 x 16 Socket Pan Head Screw
6ram Flat Washer*
6-1.0mm Fiber Hex Nut*

13
14
15

32669.00
STD851004
STD852004

Plate
4mm Flat Washer*
4mm Lock Washer*

16
17
18

STD863410
STD835030
STD840812

19
20
21
22

31133.00
31134.00
31282.00

4-0.7 x lOmm Pan Head Screw*
8-1.25 x 30mm Hex Head Bolt*
8-1,25mm Hex Nut*
Rubber Pad

5
6
7

31136.00
31137.00

QTY,
1
30
2
1
4
4
4
1
2
2
2
2
1
4
4
4
1
1
1

Wrench
Knob
Rear Panel

1
1
1

Right Rear Corner Support

Standard hardware item available locally.

31168.00

Model 351.218331

Figure 57 - Replacement

Parts Illustration

for Rails

45
i

KEY
NO.
1
2

PART NO.
31138.00
31558.00

DESORIPTION
Paddle
Switch

3
4

17933.00
STD863508

Circuit Breaker,15A
5-0.8 x 8mm Pan Head Screw*

5
6
7

STD852005
STD851005
01474.00

5mm Lock Washer*
5mm Flat Washer*
5mm Serrated Washer

8
9
10

31128.00
31139.00
31140.00

Strain Relief

11
12
13

STD840610
STD851006
STD852006

6-1.0mm Hex Nut*
6mm Flat Washer*
6mm Lock Washer*

14
15
16

STD833016
32738.00
32739.00

6-1.0 x 16mm Hex Head Bolt*

17
18
19

31143.00
32740.00
32741.00

20
2I
22

31146.00
STD835025
31147.00

23
24
25

STD851008
STD852008
STD840812

26
27
28
29

STD835020
8TD851 OO8
STD852008
STD845812

3O
31
32

31148.00
31149.00
31150.00

33
34
35

31151.00
31152.00
31153.00

36
37
38

STD836025
STD852010
STD851010

39
40

31154.00
31155.00

41
42
4_3

31156.00
07458.00
31157.00

44
45
46

08560.00
31169.00
32742.00

36998.01

*
A

QTY.
1
1
1
2
2
2
2
2
3
1

Tapping Screw
Switch Plate

2
2
2
2
1

Right Front RaiI Cap
Right Front Rail
Front Partition
Left Front Rail

1
1
1
1
1
8

Left Front Rail Cap
Scale (2 piece)
8-1.25 x 25mm Hex Head Bolt*
8-1.25 x 28mm Hex Head BoIt

8
16
16

8mm Flat Washer*
8ram Lock Washer*
8-1.25mm Hex Nut*
8-1.25 x 20mm Hex Head Bolt*
8ram Flat Washer*
8mm Lock Washer*

16
4
4
4
4

8-1.25mm Cap Nut*
Brace

1
1

Right Rear Rail Cap
Right Rear Rail
Rear Partition
Left Rear Rail

1
1
1

Table Extension
10-1.25 x 25mm Hex Head Bolt*
10mm Lock Washer*

2
6
6

10mm Flat Washer*
Table

6
1
1

Left Rear Rail Cap
Table Insert
5-0.8 x 10mm Flat Head Screw

1
4
1

Magnet
8-1.25 x 16mm Set Screw
Switch Box

2
1
6

3.9 x 8mm Flat Head Tap Screw
Operator's Manual

Standard hardware item available locally.
Not shown.

KEY
NO. PART NO.

=,-L

QTY.

KEY
NO. PART NO.

DESCRIPTION

QTY.

16096.00

8-1.25 X 16rnm Socket Pan Head Screw

31171.00

2
3
4

06346.00

6-1.0 x 12mm Socket Pan Head Screw
Corner Support
Foot
8-1.25mm Fiber Hex Nut*

19
2O
21
22
23

31172.00
22462.00
04491.00

5
6
7

31163.00
31164.00
STD843812
31165.00
STD835060

24
4
4
8
4

8
9

32085.00
31167.00

Front/Rear Base Panel

4
2
2

24
25
26

05981.00
31173.0O
31174.00
32086.00
31176.00

4
4

27
28

16109.00
31177.00

6 x 25mm Spring Pin
Foot Pedal

4
4
2

29
3O
31

Caster Support
Dust Chute
6-1.0mm Hex Nut*

4
4
4

32
33
34

31178.00
31179.00
STD840610
STD851006
32087.00
31181.00

Right Base Panel

2
2
!

Rip Fence Bracket

10
11
12

DESCRIPTION

STD851010
STD852010

13
14

01002.00
31170.00
STD870616

15
16
17

STD870512
STD852005
STD851005

Caster Asso"mbly
8-1.25 x 60turn Hex Head Bolt*
Caster Support
10mm Flat Washer*
! 0rnm Lock Washer*
10-I .5 x 25mm Socket Head Bolt
Cam
6-1.0
5-0.8
5mm

Plate Assembly
x 16mrn Socket Head Bolt*
x 12ram Socket Head Bolt*
Lock Washer*

5mm Fiat Washer*

* Standard hardware item available locally.

Blade
Blade
3-0.5
3mm
3ram
Push

Guard Bracket, Front
Guard Bracket, Rear
x 10mm Pan Head screw
Lock Washer
Flat Washer
Stick Bracket

Push Stick
Left Base Panel
Caster Shaft

6mm Flat Washer*

1
1
4
4
4
1
1
1
2
4
2
2
1

Model 351.218331
Figure 59 - Replacement Parts Illustration for Blade Drive

25
28
6

8
9

12
19

34
51
52

61
17 16

'67

KEY
NO.
1

PART NO,
iSTD835016

DESCRIPTION
8-1.25 x 16mm Hex Head Bolt*

2
3
4

STD852008
16716.00
STD843620

8mm Lock Washer*

5
6
7

STD851016
31182.00
STD843217

8
9

04293.00
31183.00

10
11
12

31184.00
31185.00
02803,00

13
14

31186.00
STD315225

15
16
I7

ST D870620
STD852006
STD851006

18
19
20
21
22

31234.00
31188.00
31189.00
STD315235
31190.00

23
24

31191.00
STD851005

25
26
27

STD852005
STD863512
31192.00

28
29
30
31

31193.00
31194,00
31195.00
31196.00

32
33

07215.00
31197.00

34
35
36

31198.00
31199.OO
STD851010

37
38
39

STD852010
STD836030
31200.00

40
41
42

STD843550
31201.00
3I 202.0O

31203.00

8mm Flat Washer (W)
16-2.0mm Fiber Hex Nut*
16mm Flat Washer*

1
1
1

Motor
12-1.75mm Fiber Hex Nut*

I
1
1

6 x 6 x 20mm Key
Motor Pulley
Drive Belt

KEY
NO,

QTY.
1
1

1
1
1

44
45
46
47
48
49
5O
51
52
53

54
55

Bushing
6202LS Ball Bearing*
6-1.0 x 20mm Socket Head Bolt*
6mm Lock Washer*

1
1
2
5

56
57
58
59

6mm Flat Washer*
Pointer Base

6
1

60
61

Motor Bracket

1
1
1

62
63
64

1
1
2
2

65
66
67
68

2
2
1
2

69
70
71
72

2
1

73
74

2
1
2
1

75
76
77
78

4
4

79
8O

4
1

81
82

1
1
1
1

83
84
85
86

Arbor Pulley
6-1.0 x 12 Set Screw

Arbor Locking Bushing
6203LL Bali Bearing*
Spring
Locking Pin w/knob
5mm Flat Washer*
5mm Lock Washer*
5-0,8 x 12mm Pan HeadScrew*
Lock Knob
Bevel Stop Support
Spacer
Handle Assembly
Spring
5 x 5 x 15mm Key
Arbor
Shim
Rear Trunnion
10mm Flat Washer*
10mm Lock Washer*
10-1.25 x 30mm Hex Head Bolt*
3CMI-3.5 Retaining Ring
3-0.5mm Fiber Hex Nut*
Adjustment Latch
3-0.5 x 18ram Pan Head Screw
Bushing

* Standard hardware item available locally

PART NO.
31204.00
07383.00
31205.00
31206.00
31207.00
31208.00
31209.00
31210.00
31211.00
31212.00
31213.00
STD870610
31214,00
STD863612
31215.00
31216.00
31217.00
31218.00
31219.00
03069.00
31220.00
01882,00

DESCRIPTION
Bevel Plate

QTY.
1

3CMI-9 Retaining Ring

Spacer
Bracket

I
1

Spring
Lock Pin

1
1

Riving Knife
Plate

1
1

Bearing
Locking Knob
6-1.0 x 10mm Socket Head Bolt*

1
1
2

Tilt Shaft
6-1.0 x 12mm Pan Head Screw*
Lower Blade Guard

1
2
1

Arbor Nut

Flange
Blade

1
1

3AMI-48 Retaining Ring
5-0.8 x 6ram Set Screw
Pin
5-0.8 x 12mm Hex Head Bolt

1
3
1
1

31221.00
Mounting Plate
31222.00
Spring
31660.0O
Screw
STD843508 5-0.8mm Fiber Hex Nut*

31661.00
06388.00
31225.00

Spring Plate
3CMI-4 Retaining Ring
Shim Washer
Shaft
Main Trunnion

1
1
1
1
1

10-1,5mm Hex Nut*
10-1.5 x 55mm Socket Head Bolt
Rear Trunnion

1
1
1

31226.00
32102.00
STD841015
02592.00
31228.00
31229.00
01939,00
06821,00
31230.00
31231.00
31232.00
STD863408
STD851004
31233.00

1
1
1

Elevation Shaft

3 x 20mm Spring Pin
3CM1-12 Retaining Ring

2
2

Spacer
Beveled Lock Washer
Shaft Base
4-0.8 x 8mm Pan Head Screw*

2
1
1
1

4mm Flat Washer*
Pointer

1
1

Model 351.218331
Figure 60 - Replacement

Parts Illustration

for Blade Guard

f11.

20--!
,

"k''17
2

2_2

/15

22 21

__j15

13 o

;4__16

KEY
NO,
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
3O
31
32
33
34
35
36
37
A

PART NO.
NIA

DESORIPTION
6-1.0 x 58ram Hex Head Bolt

STD840610
STD85I 006
N/A

6-1.0mm Hex Nut*
6mm Flat Washer*
Spacer
Left Blade Guard

3
1

NIA
N/A
N/A

Bushing
Cover
4-0.7 x 15mm Set Screw
4-0.7 x 10mm Flat Head Screw

2
2
2

N/A
NiA

Support
Body

31243.00
N/A
N!A
N/A

Right Blade Guard
Bushing Plate
Pivot Pin

31237.00
NiA

NiA
N!A
N!A

N!A
NiA
31253.00

Support
Knob

STD840508
STD863520
STD863410
STD851004
NiA
N!A
N/A
NiA
NiA
N/A
O9956.00
31621.00
31622.00

1
I
1
1
3
2
1
1
1

Spring
Pivot Pin
3CM1-9 Retaining R!n.g .......
Pawl

N!A
31255.00

4
1

4 x 12mm Spring Pin
Latch
3-0.5 x 8mm Set Screw

NiA
N/A
NiA

31623.00
*
z_

QTY.
1
3
2

2
2
2

Bushing

Spacer
Miter Gauge
5-0.8mm Hex Nut*
5-0.8 x 20mm Pan Head Screw*
4-0.7 x 10mm Pan Head Screw*
4mm Flat Washer*
Pointer
Block
Pin

1
1
1
1
3
3
1
1
1
1
1
1
1

Stop Pin
Bar
Washer

1
1
1

6-1.0 x 8mm Flat Head Screw
Miter Gauge Assembly
Pawl Assembly
Blade Guard Assembly

1
1

Standard hardware item available locally.
Not shown.

N/A Not available as replacement part.

Get it "

, at your home or ours!
Your Home

For troubleshooting,

product manuals and expert advice:

managemylife
www.managemylife.com

For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances
and items like garage door openers and water heaters.

1-800-4-MY'-HOME ®
I

Call anytime,

(1-800,-469-4663)

day or night (U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home
!

For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest

]
[

Sears Parts & Repair Service Center

1-800-488-1222

(U.S.A.)

www.sears.com

To purchase a protection

1-800-827-6655

agreement

(U.S.A.)

Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:

1-888-SU-HOGAR

(1-888-784-6427)

www.sears.com

® Registered

Trademark

1-800-469-4663

(Canada)

www.sears.ca

on a product serviced by Sears:

1-800-361-6665

(Canada)

Au Canada pour service en frangais:

1-800-LE-FOYER

(1-800-533-6937)
www.sears.ca

sears

t "ruTrademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries

® Marca Registrada 1TM Marca de F_brica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises
MCMarque de commerce I MD Marque d6posCe de Sears Brands, LLC

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 36
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sat Mar 29 10:37:16 2014
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 141218331 User Manual SAW TABLE^ Manuals And Guides 1310502L

Navigation menu

Versions of this User Manual:

Views

Navigation