Craftsman 315175502 User Manual BISCUIT JOINER Manuals And Guides L0807585
CRAFTSMAN Plate Joiner Manual L0807585 CRAFTSMAN Plate Joiner Owner's Manual, CRAFTSMAN Plate Joiner installation guides
User Manual: Craftsman 315175502 315175502 CRAFTSMAN BISCUIT JOINER - Manuals and Guides View the owners manual for your CRAFTSMAN BISCUIT JOINER #315175502. Home:Tool Parts:Craftsman Parts:Craftsman BISCUIT JOINER Manual
Open the PDF directly: View PDF 
.
Page Count: 26
| Download | |
| Open PDF In Browser | View PDF |
OPERATOR'S MANUAL I:RRFTSMRN DETAIL BISCUIT JOINER DOUBLE INSULATED Model No. 315.1 75502 O A WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.com/craftsman 983000-5t 9 5-05 Estates, IL 60179 USA Save this manual for future reference O • Warranty .......................................................................................................................................................................... 2 • Introduction ..................................................................................................................................................................... 2 • General Safety Rules .................................................................................................................................................... • Specific Safety Rules ....................................................................................................................................................... • Symbols ........................................................................................................................................................................ • Electrical .......................................................................................................................................................................... • Features ........................................................................................................................................................................ • Assembly ......................................................................................................................................................................... • Operation .................................................................................................................................................................. 10-t9 • Maintenance ............................................................................................................................................................. 20-22 • Accessories ................................................................................................................................................................... 23 • Troubleshooting ............................................................................................................................................................. 23 • Exploded View and Parts List ................................................................................................................................... • Parts Ordering/Service ..................................................................................................................................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3-4 4 5-6 7 8-9 9 24-25 Back Page TOOL If this CRAFTSMAN tool fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears will repair it, free of charge. If this CRAFTSMAN of purchase. tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 This tool has many features for making its use more pleasant and enjoyable. Safety, performance, have been given top priority in the design of this product making it easy to maintain and operate. and dependability A WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. • Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. • Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents. SAVE THESE INSTRUCTIONS WORK AREA • • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. • Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL • • Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation [] eliminates the need for the three-wire grounded power cord and grounded power supply system. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. • Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W". These cords are rated for outdoor use and reduce the risk of electric shock. PERSONAL • • • • SAFETY • • • TOOL USE AND CARE • • • • • Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. • Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the tool in unexpected situations. • • Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleumbased products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic. SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. • Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the cutting tool "live" and shock the operator. • Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury. • Always wear safety glasses. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious personal injury. • Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury. • Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury. • • _ Inspect tool cords periodically and, if damaged, have repaired at your nearest Authorized Service Center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or fire. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of shock, fire, or serious injury. • Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 16 is recommended for an extension cord 50 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. • Inspect for and remove all nails from lumber before using this tool. Following this rule will reduce the risk of serious personal injury. • Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction contains chemicals known to cause cancer, birth defects or other reproductive chemicals are: • lead from lead-based paints, activities harm. Some examples of these • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic no No Load Speed Rotational speed, at no load [] Class II Construction Double-insulated .../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute @ Wet Conditions Alert Do not expose to rain or use in damp locations. min Read The Operator's O A ® @ @ Manual of current construction To reduce the risk of injury, user must read and understand operator's manual before using this product. Eye Protection Always wear safety goggles, safety glasses with side shields, or a full face shield when operating this product. Safety Alert Precautions that involve your safety. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. No Hands Symbol Failure to keep your hands away from the blade will result in serious personal injury. Hot Surface To reduce the risk of injury or damage, avoid contact with any hot surface. Thefollowingsignalwordsandmeanings areintendedto explainthe levelsofriskassociatedwiththisproduct. SYMBOL _i, ,_ SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. CAUTION: (Without Safety Alert Symbol) Indicates a situation property damage. SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts. ,_k A that may result in WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing others who may use this product. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles, safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.t. SAVE THESE INSTRUCTIONS DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. _ WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool's internal insulation. Observe all normal safety precautions to avoid electrical shock. NOTE: Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELECTRICAL CONNECTION This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current}. Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check the power supply. EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used. When working outdoors with a tool, use an extension cord that is designed for outside use. This type of cord is designated with "WA" on the cord's jacket. Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation. **Ampere rating (on tool faceplate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0 Cord Length Wire Size (A.W.G.} 25' t6 t6 t6 t6 t4 t4 50' t6 t6 t6 t4 t4 t2 100' 16 16 14 12 10 -- **Used on 12 gauge - 20 amp circuit NOTE: AWG = American Wire Gauge A A WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury. WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. PRODUCT SPECIFICATIONS Fence Angles ................................................... 45 ° and 90 ° No Load Speed ............................................... Depth of Cut with Micro Depth of Cut Adjustment ........................ 0 - 9/32 in. 19,000/min. Input ................................ 120 V, 60 Hz, AC only, 3.5 Amps Net Weight ........................................................... 3.878 Ibs. Fence Height Adjustment With Fence Angle Set on 90 ° ......................... 0 - 3/4 in. With Fence Angle Set on 45 ° ........... 5/16 in. - 13/16 in. LINEOF CUT WINDOW CENTERLINE/ LINE OF CUTINDICATOR MARK(S) REARHANDLE 0 0 SWITCH TRIGGER WIDTH OF CUTSCALE JAM NUT KNURLED ADJUSTMENT KNOB REVERSIBLE FENCE DEPTH ADJUSTMENTKNOB HEIGHT SETTINGSCALE HEIGHT ADJUSTMENT KNOB(S) NONSKID SURFACE HEIGHT INDICATORMARK Fig. 1 KNOW YOUR DETAIL BISCUIT JOINER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. REVERSIBLE FENCE The reversible fence can be removed through key hole slots and rotated t80 ° to change the angle of cut to 90 ° or 45 ° . The fence should always be used to guide and balance the biscuit joiner, providing ease of operation and maintaining control. HEIGHT SETTING SCALE A scale on each side of the fence indicates the height of the fence from the center of the blade. KNURLED ADJUSTMENT KNOB Fine adjustments may be made by using the knurled adjustment knob and jam nut. CENTERLINE/LINE OF CUT INDICATOR Centerline and line of cut indicator marks help the operator make more accurate cuts. NON-SKID SURFACE Your biscuit joiner has a t-1/2 in. 6-tooth blade for cutting biscuit slots. The fence on the biscuit joiner has a non-skid surface to help prevent misalignment caused by skidding during use. It also prevents marring of the workpiece when making cuts. DEPTH BISCUITS BLADE ADJUSTMENT KNOB(S) A spring-loaded depth adjustment knob makes it possible to make proper settings for three standard size biscuits. Fine adjustments to the cutting depth can be made with a knurled adjustment knob and jam nut located behind the depth adjustment knob. Once the correct depth setting has been made for one biscuit size, the other two depth settings will be automatically set. HEIGHT ADJUSTMENT KNOBS Biscuits swell rapidly upon contact with water-based woodworking glues and should be stored in a dry place. They are available in three standard sizes: R1 (7/32 in. x 5/8 in.) R2 (9/32 in. x 3/4 in.) R3 (1/2 in. x 1 in.) This biscuit joiner is packaged with 25 R3 biscuits. The height of the fence at 90 ° can be set between 0 - 3/4 in. from the center of the blade. The height of the fence at 45 ° can be set between 5/16 in. - 13/16 in. from the center of the blade. UNPACKING a, This product has been shipped completely assembled. • Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. • If any parts are damaged or missing, please call t -800-932-3188 for assistance. PACKING LIST Biscuit Joiner R3 Biscuits (25) Operator's Manual A WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. A WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury. • A • A depends on the thickness of the wood and the length of the joint. In general, the small #R1 biscuits should be used for miter cuts in 3/4 in. materials. The larger biscuits should be used for edge-to-edge joinery. WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. TURNING A JOINER ON/OFF See Figure 2. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. A THE BISCUIT To turn on the biscuit joiner, depress the switch trigger. Release the switch trigger to turn the biscuit joiner off. WARNING: Always use a firm grip with both hands and clamp your workpiece securely when operating the biscuit joiner, to avoid loss of control and possible serious injury. APPLICATIONS You may use this tool for the purposes listed below: • SWITCH TRIGGER Cutting precise mating oval slots in hard wood, soft wood, plywood and particle board SPLINE Fig. 2 JOINERY Spline joinery is one of the strongest methods of joinery used in woodworking. When glue is properly applied to a spline and to the joint area of the wood pieces being connected, a large surface area receives the adhesion properties of the glue. This forms a strong joint. OPERATING THE BISCUIT JOINER See Figure 3. When operating the biscuit joiner, hold the tool with both hands. Keep one hand on the rear handle and place your other hand on the top and front portion of the motor housing. Traditional spline joinery requires cutting slots with a router or table saw. Small, thin strips of wood must then be cut to fit inside the slots and act as splines. CAUTION: Avoid hand positions that cover the air vents on the motor housing of the tool. Covering the air vents can cause motor burnout. Newer methods of spline joinery use a plate or biscuit joiner to cut precise mating oval slots in adjoining boards. This biscuit joiner is a fast, simple, and accurate plungecutting tool that can be used to cut slots in hardwood, softwood, plywood, particle board, and other pressed woods. PROPERHANDPOSITION REARHANDLE Football shaped wafers, called biscuits, are then placed inside the slots with glue and used to help line up adjoining surfaces. When a water based glue is used, the biscuits swell in the joint, making an extremely strong and firm bond. White glue, yellow glue, carpenters glue, hide glue, and aliphatic resin glue are examples of water-based glues. This bonding technique has traditionally been limited to making edge-to-edge joints. However, with the use of this biscuit joiner, biscuits can now be easily used to connect butt, miter, and T-joints. Biscuit joining can be as strong as mortise and tenon, tongue and groove, standard spline, and doweled joints. In most cases the material around the biscuit will break before the biscuit itself will break. A greater surface area is exposed to glue in a biscuit joint, making the seams stronger. A variety of spline joints can be made using the biscuit joiner. The number and size biscuits needed for each joint 10 TOP OFTOOL A WARNING: Always unplug the tool when changing operation settings or when the tool is not in use. Failure to unplug the tool may result in accidental starting and serious personal injury. DEPTH OF CUT Depth of cut is a basic setting that must be adjusted for all biscuit joinery applications. The biscuit joiner can be adjusted to three standard cutting depths to accommodate three standard size biscuits -- Rt, R2, and R3. Adjustments are made by engaging slots on depth adjustment knob with tabs on rear base. For example, when using the R1 size biscuit, rotate the depth adjustment knob until the slot marked 1 aligns with the depth indicator mark on the rear base. When using an R2 size biscuit, rotate the depth adjustment knob until the slot marked 2 aligns with the depth indicator mark on the rear base, and when using an R3 size biscuit, rotate the depth adjustment knob until the slot marked 3 aligns with the depth indicator mark on the rear base. SETTING DEPTH ADJUSTMENT TABS JAM NUT KNOB KNURLED ADJUSTMENT KNOB See Figure 4. • Unplug the tool. • Select the correct depth of cut setting for the biscuit size you plan to use. To select depth of cut, pull the knurled adjustment knob and jam nut in the direction of the arrow. NOTE: The knob and jam nut are spring loaded. Pulling them in the direction of the arrow puts pressure on the spring and releases pressure from the depth adjustment knob. • Rotate the depth adjustment knob until the desired slot setting aligns with the tabs on the rear base - 1,2, or 3. • Release the knurled adjustment knob and jam nut. DEPTH ADJUSTMENTKNOB SLOTS 11 Fig. 4 MAKING FINE ADJUSTMENTS FENCE HEIGHT ADJUSTMENT See Figure 5. See Figure 6. Make a test cut in a scrap piece of wood. Fit the correct size biscuit into the biscuit slot. The biscuit slot should The fence on the biscuit joiner can be moved up and down to adjust the position of the blade in relation to the top of the workpiece. A scale on both sides of the front base indicates height settings for both 45 ° and 90 ° angles. The fence and height indicator mark can be positioned from 5/16 in. to 13/16 in. from the center of the blade for be deep enough to allow slightly more than one-half of the biscuit into the slot. This extra room allows for proper alignment of the wood being joined. If the biscuit slot is too deep or too shallow, fine adjustments to the depth setting can be made by loosening the knurled adjustment knob and making fine adjustments with the jam nut. 45 ° angles. It can be positioned from 0 to 3/4 in. from the center of the blade for 90 ° angles. Scale marks are in increments of t/16 in. FENCE • Unplug the tool. • Loosen the knurled adjustment knob. This knob is used as a lock nut only. Loosen by twisting it in the opposite direction away from the jam nut. • Rotate the jam nut to the right for a more shallow cut, or to the left for a deeper cut. • Once desired depth of cut is reached, hold the jam nut so that it will not move out of adjustment. Next, tighten the knurled adjustment knob against jam nut. • Recheck the depth setting by making scrap piece of wood. Also periodically setting for accuracy. Rotating the jam will cut shallow biscuit slots. Rotating the left will cut deeper biscuit slots. HEIGHTADJUSTMENT KNOB(S)_'_ a test cut in a check the depth nut to the right the jam nut to HEIGHT SETTINGSCALE Fig. 6 TO LOWER FENCE ADJUSTING THE HEIGHT SETTING See Figure 7. • Unplug the tool. • Loosen the two height adjustment knobs, • Pull the fence forward and slide it up or down until the height indicator mark is aligned with the desired dimension on the scale. NOTE: Slots in the front base align with a tab on the backside of the fence. This alignment keeps the fence square at each height setting. • ROTATECLOCKWISEFOR SHALLOWBISCUITSLOTS ROTATE COUNTERCLOCKWISE FOR DEEPERBISCUITSLOTS Tighten height adjustment knobs securely. HEIGHT ADJUSTMENT KNOBS Fig. 5 (1) PULL FORWARD FRONT BASE (2) SLIDE DOWN 12 FENCE Fig. 7 FENCE ROTATION/ANGLE ADJUSTMENT LINE OF CUT INDICATORS See Figure 8. See Figure 9. The fence on the detail biscuit joiner can be rotated t80 ° and set at either 45 ° or 90 ° angles. The detail biscuit joiner has a centerline/line of cut indicator on the reversible fence and a centerline indicator mark • Unplug the tool. • • Loosen the two height adjustment knobs. Pull the fence forward and slide it down the front base until it can be removed through the key hole slots. Rotate the fence t80 °. on the bottom side of the bottom shoe to help you make accurate cuts. • • When making a cut for biscuit joints, determine the location of each biscuit spline joint and mark a centerline of the joint by drawing a line across each workpiece. Align the mark on the board with the centerline indicator on the tool. Reinstall the fence on the front base. Place height adjustment knob bolts in key hole slots and align bolt heads with the slots on back of front base. • Slide fence up the front base to desired depth of cut. • Tighten height adjustment knobs securely. FENCEORIENTATION FOR45 ° ANGLES TABS BOTTOMSIDE OFBOTTOMSHOE CENTERLINE MARK ON WORKPIECE INDICATOR MARK FENCEORIENTATION FOR90° ANGLES HEIGHT ADJUSTMENT KNOBBOLT(S) INDICATOR MARK(S) LINEOF CUT WINDOW CENTERLINEMARK ON WORKPIECE SLOTS BISCUIT KEY HOLESLOTS SELECTION The number and size of biscuits needed for each joint depends on the thickness of the wood and the length of the joint. In general, the small R1 biscuits should be used for miter cuts in smaller, thinner materials. The larger biscuits should be used for edge-to-edge joinery. FRONT BASE SLOT(S) Fig. 9 When joining thick materials, such as 2 in. x 4 in. dressed lumber, stack two biscuits, one above the other. When joining even thicker materials, use additional biscuits, stacked above each other. Fig. 8 The following sections illustrate how to make various spline joints using the detail biscuit joiner. 13 A • WARNING: Always use a firm grip with both hands and clamp your workpiece securely when operating the biscuit joiner, to avoid loss of control and possible serious injury. MAKING EDGE-TO-EDGE Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. JOINTS See Figures 10- 12. Edge-to-edge joinery is one of the most basic and easilyconstructed joints. • Unplug the tool. • Prepare the workpieces by laying them side by side on a workbench in the order in which they will be assembled. • Using a square, determine the location of each biscuit spline joint and mark the center of each joint by drawing a line across each workpiece. Mark edges t in. from the ends of workpieces. NOTE: The joint will be stronger if you use multiple biscuits placed close together. STACKEDBISCUITSLOTS BISCUITSLOT(S) Fig. 10 • Set fence angle at 90 °. • Loosen the height adjustment knobs, then pull and slide the fence up or down until the indicator point is aligned with the desired dimension on the scale. • When the base assembly bottoms out against the depth of cut adjustment knob setting, pull back, releasing pressure on the spring. The blade will retract from the biscuit slot. • Repeat this procedure for all desired biscuit slots and for cutting the slots in the mating workpiece. • Once all biscuit slots have been cut, place a biscuit in each joint and dry-assemble the workpieces. Make sure each joint lines up and fits. • Disassemble the workpieces and place a bead of glue in each slot. Spread a bead of glue over the entire surface of the joint. Reinsert the biscuits and assemble the workpieces. EDGETO EDGEJOINTS CENTERLINE MARKS NOTE: The scale indicates the height of the fence from the center of the blade. • Tighten the height adjustment knobs securely. • Select the correct depth of cut setting to match the biscuit size you are planning to use. If possible, make a test cut in a scrap piece of wood from the same workpiece. • Clamp workpiece securely so it will not move during the cut. • Plug the biscuit joiner into the power supply and prepare to make your first cut. Grasp and hold the tool securely. • Fig. t 1 BISCUIT SLOT(S) Place the fence against the board and align the indicator marks on the fence with the centerline mark(s) on the board. BISCUIT(S) 14 Fig. t2 BUTT JOINTS • Place the fence against the board and align the indicator marks on the fence with the centerline mark(s) on the board. • Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. • When the base assembly bottoms out against the depth of cut adjustment knob setting, pull back, releasing pressure on the spring. The blade will retract from the biscuit slot. • Repeat this procedure for cutting the slot in the mating workpiece. • Once all biscuit slots have been cut, place a biscuit in each joint and dry-assemble the workpieces. Make sure each joint lines up and fits. • Disassemble the workpieces and place a bead of glue in each slot. Spread a bead of glue over the entire surface of the joint. Reinsert the biscuits and assemble the workpieces. • Clamp the workpieces together until the glue sets. See Figure 13. This type of joint is made by mating the end grain of one board with the edge grain of another. It is one of the weakest joints in woodworking, and the bonding of glue on this type of surface is poor. However, by using biscuits you can create a stronger joint that has a mortise-and-tenon effect. BUTTJOINTS BISCUIT(S) BISCUIT SLOT(S) OFFSET BUTT JOINTS See Figure 14. MULTIPLE BISCUITSSTACKED MAKING The rails of a table or workbench are often offset from the front of the table legs. When offsets are required, it is necessary to cut the slots in the rails first, then re-adjust the fence to cut the slots in the legs. CENTERLINE MARK(S) Fig. 13 The procedure for cutting offset butt joints is identical to the procedure for cutting butt joints. BUTT JOINTS • Unplug the tool. • Place the two pieces of wood to be joined on a level workbench. Align them against each other in the arrangement in which they will be assembled. • Using a square, determine the location of each biscuit spline joint and mark the center of each joint by drawing a line across the edges of the two boards. • Set the fence angle at 90 °. • Loosen the height adjustment knobs, then pull and slide the fence up or down until the indicator point is aligned with the desired dimension on the scale. For example, if a 1/4 in. offset is desired, you would mark the centerlines for cutting a butt joint as mentioned in the procedures for cutting butt joints, and cut the slots in the ends of the rails. Next, you would raise the fence t/4 in. to the desired offset and cut the slots in the legs. OFFSETBUTTJOINT BISCUITSLOT NOTE: The scale indicates the height of the fence from the center of the blade. • Tighten the height adjustment knobs securely. • Select the correct depth of cut setting to match the biscuit size you are planning to use. If possible, make a test cut in a scrap piece of wood from the same workpiece. • Clamp the workpiece securely so that it will not move during the cut. • Plug the detail biscuit joiner into the power supply and prepare to make your first cut. Grasp and hold the tool securely with both hands. BISCUIT CENTERLINE MARK(S) Fig. 14 15 T-JOINTS • Plug the tool into the power supply and cut slots in all boards that require end slots. Follow the procedures as explained in "Making Edge-To-Edge Joints." • Rotate the fence angle to 90 °. Set the fence height at the desired dimension on the scale. • Select the correct depth of cut setting for the biscuit size you plan to use. • • Clamp the workpiece securely. Cut each slot at the marked centerline intersection. • Next, you must remove the fence from the biscuit joiner in order to cut slots into the face of the vertical board. See Figures 15- 18. A T-joint is used when the end of a board is joined to the face of another board. Typical applications include attaching shelves to bookcases and inner support braces to frames. Actual cutting of a T-joint is as simple as any other cut. However, it is critical that you mark the centerlines, mark the intersection points for each slot, and cut each slot correctly. T-JOINTS CENTERLINEMARK(S) HORIZONTALBOARD /(( ! (), | BISCUIT(S) BASEPLATE CLEARANCE Fig. t 5 MAKING SURFACE 1"-JOINTS • Unplug the tool. • Place the two pieces of wood to be joined on a level workbench. The inside face of the vertical board CLAMP TO REMOVE should be facing up. HORIZONTAL BOARD "__X_ A BISCUITSLOT CENTERLINE MARK(S) / BOARD CENTERLINES • • • • VERTICALBOARD CONTACT TO CUTEND SLOTSIN HORIZONTALBOARD Fig. t7 FENCE: WARNING: When the fence is removed, the cutter may be exposed. Use extreme caution to avoid serious personal injury. Unplug the tool. Loosen the height adjustment knobs. Pull the fence forward and slide it down the front base until it can be removed through the key hole slots. Select the correct depth of cut setting for the biscuit size you plan to use. Clamp the workpiece securely, and cut each slot at the marked centerline intersection. Fig. t6 Determine the location of each biscuit joint and mark the centerlines on each board. The centerlines for both boards must line up with each other. Measure carefully, these measurements must be accurate and precise. NOTE: Measure twice and cut once. In addition to the centerlines lining up, the spacing of the biscuit slots from side to side must also match. KEYHOLESLOTS 16 Fig. t8 CUTTING VERTICAL BOARDS FOR T-JOINTS • When the base assembly bottoms out against the depth of cut adjustment knob setting, pull back, releasing pressure on the spring. The blade will retract from the biscuit slot. • Repeat this procedure for cutting all required slots in vertical boards. • Once all slots have been cut, place a biscuit in each joint and dry-assemble the workpieces. Make sure each joint lines up and fits. • Disassemble the workpieces and place a bead of glue in each slot. Spread a bead of glue over the entire surface of the joint. Reinsert the biscuits and assemble the workpieces. • Clamp the workpieces together until the glue sets. See Figure 19. • • With the tool unplugged and the fence removed, place the detail biscuit joiner on a vertical board and align the indicator marks on the bottom shoe with the centerline on the vertical board. Place a straight piece of wood on the vertical board and securely clamp it flush against the bottom shoe. This piece of wood is used for a fence or guide. It must be square with the sides of the vertical board and parallel with the centerline. TO CUTSLOTSIN VERTICALBOARDS BOTTOMSIDE OFBOTTOMSHOE CENTERLINE MARKON WORKPIECE Upon completion of a T-joint cutting operation, reinstall the fence on the front base by reversing "To Remove Fence" procedure. INDICATOR MARK CLAMP VERTICALBOARD Fig. t9 • Align the centerline on the bottom of the shoe with marked intersection for the biscuit slot. • Plug the tool into the power supply and prepare to cut the slot. • Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. 17 • Place the height adjustment knob bolts in the key hole slots. • Align bolt heads with the slots on the back of the front base. • Slide the fence up the front base to the desired depth of cut. • Tighten the height adjustment knobs securely. MITER JOINTS • Disassemble the workpieces and place a bead of glue in each slot. Spread a bead of glue over the entire surface of the joint. Reinsert the biscuits and assemble the workpieces. • Clamp workpieces together until the glue sets. See Figures 20-22. There are two types of miter joints that can be made using biscuits: flat miters and edge miters. Flat miters are used when making picture frames. Edge miters are used when making boxes or things where you don't want to show the end grain of the wood. Butt joints show the end grain in wood. MAKING MAKING FLAT MITER JOINTS • Unplug the tool. • Place the pieces of wood to be joined on a level workbench. • Using a combination square, draw a line through the center of each joint perpendicular to the mitered edges. EDGE MITER JOINTS • Unplug the tool. • Place the pieces of wood to be joined on a level workbench. • Mark the centerline of the joint on each board. EDGEMITER JOINTS FLATMITER JOINTS CENTERLINE MARK(S) CENTERLINE MARK(S) BISCUIT • Fig. 21 • When making edge miter joints with workpieces that have different thicknesses, clamp them securely to a workbench with the long sides up. This will assure that the outside surfaces match. • Set the fence angle at 45 °. Fig. 20 Set the fence angle at 90 °. Set the fence height at the desired dimension on the scale. BISCUIT • Select the correct depth of cut setting for the biscuit size you plan to use. • Slide the fence up or down until the fence height is at desired setting. • Clamp the workpiece securely. • Tighten the height adjustment knobs securely. • Align the indicator mark on the fence with the centerline on the workpiece. • • Plug the tool into the power supply and prepare to cut the slot. Place the biscuit joiner on the workpiece with the fence resting on the long side of the workpiece. The front base should be against the mitered edge of the workpiece. • Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. • Recheck the fence height setting to make sure it will not cut through the workpiece. • • When the base assembly bottoms out against the depth of cut adjustment knob setting, pull back, releasing pressure on the spring. The blade will retract from the biscuit slot. Align the indicator mark on the fence with the centerline on the workpiece. Make sure the front base is pressed flat against the mitered edge of the workpiece. • Plug the tool into the power supply and prepare to cut the slot. • Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. • Repeat this procedure for cutting mating slot and all required miter joint slots. • Once all slots have been cut, place a biscuit in each joint and dry-assemble the workpieces. Make sure each joint lines up and fits. 18 • Whenthebaseassemblybottomsout againstthe depthof cutadjustmentknobsetting,pullback,releasingpressureonthespring.Thebladewillretractfrom the biscuitslot. NOTE: The scale indicates the height of the fence from the center of the blade, which is approximately .050 in. Tighten height adjustment knobs securely. CUTTINGEDGEMITER SLOT FROM LONGSIDE OF WORKPIECE HINGE FASTENERS HINGE Fig. 22 Fig. 23 • Repeat this procedure for cutting mating slot and all required miter joint slots. Select the #3 depth of cut setting. If possible, make a test cut in a scrap piece of wood from the same workpiece. • Once all slots have been cut, place a biscuit in each joint and dry-assemble the workpieces. Make sure each joint lines up and fits. Clamp the workpiece securely so that it will not move during the cut. • Disassemble workpieces and place a bead of glue in each slot. Spread a bead of glue over the entire surface of the joint. Reinsert the biscuits and assemble the workpieces. • Plug the tool into the power supply and prepare to make your first cut. Grasp and hold the biscuit joiner securely with both hands. Place the fence against the board and align the indicator marks on the fence with the centerline mark(s) on the board. Clamp the workpieces together until the glue sets. HINGE JOINTS Depress the switch trigger and let the motor build to its maximum speed, then gradually push the biscuit joiner forward to extend the blade into the wood. See Figure 23. Hinge joints are used when joining two boards using hinges supplied in one of Craftsman's optional hinge kits. Typical applications include jewelry boxes, doors on clocks, recipe boxes, etc. MAKING When the base assembly bottoms out against the depth of cut adjustment knob setting, pull back, releasing pressure on the spring. The blade will retract from the hinge slot. HINGE JOINTS • Unplug the tool. Repeat this procedure for all desired hinge slots. • Prepare the workpieces to be joined by laying them side by side on a workbench in the order in which they will be hinged. Once all hinge slots have been cut, place a hinge in each slot and dry-assemble the workpieces. Make sure each slot lines up and fits. • Determine the location of each hinge joint and mark the center of each joint by drawing a line across each workpiece. Assemble the hinges to the workpieces and secure with the fasteners supplied. • Set the fence angle at 90 °. • Loosen the height adjustment knobs, then pull and slide the fence down the scale until the height indicator mark is set at zero depth of cut. 19 ,& WARNING: BLADE REPLACEMENT When servicing, use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. ,& See Figures 24-26. After extended use, the blade may become dull. If you accidentally hit a nail or other blunt object, it will dull or break the blade. These situations require replacing the blade. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. GENERAL REPLACING Unplug the tool. Place the biscuit joiner upside down on a workbench and remove the bottom shoe screws (4) and bottom shoe. MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. A THE BLADE SCREWS(4) i WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. I i Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air. I I I I BOTTOM SHOE Fig. 24 LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. • Place a Phillips screwdriver or 3/16 in. diameter pin between the blade and front base. • Place one of the blade teeth against the screwdriver pin and lock blade preventing it from rotating, or PHILLIPSSCREWDRIVER OR3/16 IN. DIAMETERPIN BLADE FRONTBASE Fig. 25 20 • Usinga 9/64in. hexkey,removebladescrew. NOTE:Turnbladescrewcounterclockwise to remove. OUTERBLADE _) CLEANING After extended use, wood particles and resin may build up inside the base assembly of the biscuit joiner and clog the path for wood particles going through dust exhaust opening. Wood particles packing up in this area makes cutting biscuit slots more difficult. BLADESCREW BLADE BASE ASSEMBLY See Figures 27-29. GEARSPINDLE FLATS CLEANING BLADEFLATS_"_,__._ THE BASE ASSEMBLY • Unplug the tool. • Place the biscuit joiner upside down on a workbench and remove the four bottom shoe screws and bottom shoe. INNER BLADEWASHER • Remove the blade. See "Replacing the Blade." • With the biscuit joiner still upside down on a workbench, remove the two front base screws. FRONTBASE GEAR SPINDLE SCREWDRIVER Fig. 26 • Remove outer blade washer and blade. • Clean wood particles and resin from blade washer and all surrounding parts. A WARNING: If the inner blade washer has been removed, replace it before installing a new blade. Failure to do so could cause the blade screw not to tighten properly, resulting in an accident and serious personal injury. • Place the inner blade washer onto the gear spindle. • Place the new blade onto the gear spindle and align the flats on the blade with the flats on the gear spindle. Secure with the outer blade washer and blade screw. • • Place a Phillips screwdriver or 3/16 in. diameter pin between the blade and front base. • Place one of the blade teeth against the screwdriver pin and lock the blade to prevent it from rotating. SCREWHOLES Pull front base in the direction shown by the arrow in figure 27 and remove. or NOTE: Blade teeth point toward the right of the biscuit joiner when held in normal operating position. An arrow on the bottom shoe also indicates the direction of blade rotation. • Tighten the blade screw securely. • NOTE: Turn the blade screw clockwise to tighten. Reassemble the bottom shoe. • Replace the four screws and tighten securely. Fig. 27 21 • Lifttheadjustmentrodawayfromthe bearingplate andremovetherearbase. • Withfrontandrearbaseassemblies removed,place thetoolupsidedownona workbenchandcleanwood particlesandresinfrombearingplateandsurrounding areas. NOTE:Alsocleanthe blade,bladewashers,etc. (ES) TAB(S) REARBASE BEARINGPLATE SPRING(S) Fig. 28 A CAUTION: Blade tips are sharp. Be careful not to cut yourself when cleaning. Clean wood particles and resin from slots and surrounding areas on front and rear base. Apply a thin coat of general purpose grease in slots or on bearing plate where the base slides. REAR BASESLOT REAR BASESLOT ADJUSTMENT ROD FRONTBASESLOTS Fig. 29 22 • Replace the rearbase.Positionthe adjustmentrodin itsproperplaceasshowninfigure25. • Securethe rearbaseinplacewiththetwo springs. Hookoneendof eachspringinthenotchoneachside oftherearbase.Usingneedlenosepliers,stretcheach springandhookit overthetabsonthebearingplate. • Reassemble thefrontbase.Replacethescrewsand tightensecurely. • Reinstall theblade.Tightenthe bladescrewsecurely. • Reassemble thebottomshoe.Tightenthefourscrews securely. Lookfortheseaccessories atSearsretail: • Biscuits100pieces.............................................................................................................................................. SizeR1 • Biscuitst00 pieces.............................................................................................................................................. SizeR2 • Biscuitst00 pieces.............................................................................................................................................. SizeR3 • BiscuitAssortment .................................................................................................................................. 400piecestotal SizeR1............................................................................................................................................................. t00 pieces SizeR2............................................................................................................................................................. 100pieces SizeR3............................................................................................................................................................. 200pieces _k WARNING" Current attachments and accessories available for use with this tool are listed above. Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments sories not recommended can result in serious personal injury. PROBLEM Biscuits do not fit the slots. Biscuits , not fitting slots may also cause misalignment of the boards being joined. or acces- SOLUTION A. Biscuit slots are too deep or too shallow. Make fine adjustments to depth setting. See "Making Fine Adjustments." B. Biscuit thickness may be out of tolerance. Compress biscuits in a vise if they are too thick. C. Check to see if biscuits are the correct size for the size slots that have been cut: #0, #10, or #20. D. Check to see if biscuits have gotten wet and have swelled. 2. Wood particles begin to back up on the front of the unit. , Blade becomes difficult to push in when cutting slots. Blade does not retract properly when cutting slots. 4. Cutting performance is poor and there is a loss of power or stalling of motor when cutting slots. A, A. The dust port may be clogged, preventing wood particles from being drawn into the dust bag. Remove the front and rear base assemblies and clean blade, bearing plate, base assembly slots, and surrounding areas. See "Cleaning the Base Assembly." Wood particles and resin have built up on base assembly slots and surrounding areas. Remove front and rear base assemblies and clean blade, bearing plate, base assembly slots and surrounding areas. Apply a thin coat of general purpose grease in slots or on bearing plate where base slides. See "Cleaning the Base Assembly." A. Blade is dull. Replace the blade. See "Replacing the Blade." B. Resin has built up on the blade. Remove the blade and clean blade with gum and pitch remover. See "Replacing the Blade." 23 ,_ CRAFTSMAN DETAIL BISCUIT JOINER - MODEL NUMBER 315.175502 • 2 SEE NOTE "A' I 4 3 10 8 46 22 7 CRAFTSMAN DETAIL BISCUIT JOINER - MODEL NUMBER 315.175502 DETAIL BISCUIT or when repair parts. The model number JOINER will be found on aordering plate attached to the motor housing. Always mention the model number in all correspondence SEE BACK PAGE FOR PARTS ORDERING • J regarding your | INSTRUCTIONS PARTS LIST Key No. Part Number Description Qty. Key No. Part Number Description Qty. t 940078049 Data Plate ....................................................... t t7 660169036 Blade Screw (#8-32 x 3/8 in, Soc. Cap) ........ t 2 940051021 Logo Plate ....................................................... t 18 690200001 Outer Blade Washer ........................................ 1 3 671541001 Tension Spring ................................................ 2 19 671539001 Blade ............................................................... 1 4 690202001 Washer ............................................................ 2 20 671548001 Inner Blade Washer ......................................... t 5 200287002 Gear Assembly ............................................... t 2t 570287001 Front Base Pad .............................................. 1 6 200294001 Bearing Plate .................................................. 1 22 671542001 Height Adjustment Knob ................................ 2 7 660328001 * Screw (#10-24 x 3/4 in. Fil. Hd.) ..................... 2 23 342807001 Adjustable Fence ........................................... t 8 342806001 t 24 342808001 Front Base ...................................................... 1 9 660106002 1 25 660104007 Bolt (1/4-20 x 3/4 in. Sq. Hd.) ......................... 2 t0 671547001 Knurled Adjustment Knob ............................... t 26 6899902 Ball Bearing (696 ZZ) ...................................... t tl 512812001 Rear Base ....................................................... t 27 610458001 Gear ................................................................ 1 12 671540001 Compression Spring ....................................... 1 28 200234003 t3 671538001 Adjustment t Front Base w/Pad (Includes Key Nos. 21 And 24) ....................... 1 t4 660307003 983000519 Operator's Manual (not shown) 15 640872001 t6 660179002 Depth Adjustment Knob ................................. * Jam Nut (#8-32) .............................................. Rod .............................................. * Screw (#8-32 x 1/2 in. Flat Hd, T.C,) .............. 4 Shoe ................................................................ 1 (REV:0t) * Screw (#8-32 x 3/8 in, Flat Hd.) ...................... 4 NOTE: "A"- The assembly shown represents an important part of the Double Insulated System. To avoid the possibility of alteration or damage to the system, service should be performed by your nearest Sears Repair Center. Contact your nearest Sears Retail Store for Service Center information. * Standard Hardware Item -- May Be Purchased Locally Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night (U.S.A. and Canada) www.sears.com www.sears.ca Our Home For repair of carry-in items like vacuums, lawn equipment, and electronics, call or go on-line for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Call anytime, day or night (U.S.A. only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced 1-800-827-6655 (U.S.A.) Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR (1-888-784-6427) SM 1-800-361-6665 Au Canada by Sears: (Canada) pour service en fran£ais: 1-800-LE-FOYER Mc (1-800-533-6937) www.sears.ca ® Registered Trademark / TMTrademark / SM Service Mark of Sears, Roebuck and Co. ® Marca Registrada / TM Marca de Fabrica / SM Marca de Servicio de Sears, Roebuck and Co. ac Marque de commerce / MD Marque depos6e de Sears, Roebuck and Co. © Sears, Roebuck and Co.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 26 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Thu Aug 07 04:13:29 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools