Craftsman 32021228 User Manual MITER SAW Manuals And Guides L0901589
CRAFTSMAN Miter Saw Manual L0901589 CRAFTSMAN Miter Saw Owner's Manual, CRAFTSMAN Miter Saw installation guides
User Manual: Craftsman 32021228 32021228 CRAFTSMAN MITER SAW - Manuals and Guides View the owners manual for your CRAFTSMAN MITER SAW #32021228. Home:Tool Parts:Craftsman Parts:Craftsman MITER SAW Manual
Open the PDF directly: View PDF 
.
Page Count: 48
| Download | |
| Open PDF In Browser | View PDF |
Operator's Manual I:RR FTSM 10-in. COMPOUND MITER SAW and STAND COMBO Model No. 320.21228 CAUTION! Read, understand and follow all Safety Rules and Operating Instructions in this Manual before using this product. Sears, Roebuck www.craftsman.com and Co., Hoffman • • • • • • WARRANTY SAFETY UNPACKING ASSEMBLY DESCRIPTION MAINTENANCE Estates, IL 60179 i q_1:] ml_ [o_ [_o_ij_i_ Warranty Page 2 Safety Symbols Page 3 Safety Instructions Pages 4-13 Unpacking Pages 13-14 Description Pages 15-18 Assembly Pages 18-23 Adjustment Pages 23-27 Operation Pages 27-38 Maintenance Pages 38-40 Troubleshooting Pages 40-41 Parts List Pages 42-47 Sears Repair Parts Phone Numbers Back Cover ONE YEAR FULL WARRANTY If this Craftsman ON CRAFTSMAN tool fails to give complete one year from the date of purchase, States for free repair (or replacement, batteries, does not include satisfaction within return it to any Sears store or Parts & Repair Center or other Craftsman This warranty TOOL outlet in the United if repair proves impossible). expendable parts such as lamps, bits, or blades. This warranty this product applies for only 90 days from the date of purchase is ever used for commercial This warranty gives you specific if or rental purposes legal rights, and you may also have other rights, which vary from state to state. Sears, Roebuck and Co., Hoffman Estates IL 601 79 A WARNING: Some dust created by using power tools contains known to the state of California to cause cancer and birth defects reproductive chemicals or other harm. SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS! 21228 Manual Revised 08-0307 Page 2 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings de not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures. _, WARNING: Be sure to read and understand all safety instructions in this manual, including all safety alert symbols, such as "DANGER," "WARNING," and "CAUTION," before using this miter saw and tool stand. Failure to following all instructions listed below may result in electric shock, fire, and/or serious personal injury. SYMBOL MEANNING _, SAFETY ALERT SYMBOL: May be used in conjunction _, DANGER: Indicates DANGER, WARNING, with other symbols OR CAUTION. or pictographs. Failure to obey this safety warning WILL result in death or serious injury to yourself or to others. Always follow the safety precautions risk of fire, electric shock and personal injury. _, WARNING: Failure to obey this safety warning CAN result in death or serious injury to yourself or to others. Always follow the safety precautions risk of fire, electric shock and personal injury. _, CAUTION: to reduce the to reduce the Failure to obey this safety warning MAY result in death or serious injury to yourself or to others. Always follow the safety precautions risk of fire, electric shock and personal injury. to reduce the DAMAGE PREVENTION AND INFORMATION MESSAGES These inform user of important information and/or instructions that could lead to equipment or other property damage if not followed. Each message is preceded by the word "NOTE:" as in the example below: NOTE: Equipment not followed. and/or property damage may result if these instructions The operation of any miter saw can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, ALWAYS wear safety goggles or safety glasses with side shield and a full-face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shield, available at Sears Stores or other Craftsman 21228 Manual Revised 08-0307 are WEAR YOUR outlets. Page 3 _lk WARNING: Be sure to read, understand and follow all Safety rules and operating instructions in this Manual before using this tool. Failure to do so may result in electric shock, fire and/or serious personal injury. SAFETY PRECAUTIONS FOR LASERS This Miter Saw has a built-in laser light. The laser is ClasslllA and emits output power of a maximum 2.5mW and 635-655nm Class Ilia Laser Product wavelengths. These lasers do not normally present an optical hazard. However, DO NOT stare at the beam, as this can cause flash blindness. Complies with 21 CFR parts 1040.10 and 1040.11 AVOID EXPOSURE Laser radiation is emitted through this aperture t ,_ CAUTION: The following label is on the tool. It indicates the location from which the saw emits the laser light. BE AWARE of the laser-light location when using. Always make sure that any bystanders in the vicinity of use are made aware of the dangers of looking directly into the laser. • Do not remove or deface any product labels. Removing increases the risk of exposure to laser radiation. • The laser beam can be harmful to the eyes. Always avoid direct eye exposure. Do not look directly into the laser-beam-output aperture during operation. Do not project the laser beam directly into the eyes of others. • Turn the laser on only when making • The laser on the Miter Saw is not a toy. Always of children. keep it out of the reach • The laser light emitted from this device should person for any reason. never be directed • Be sure that the laser beam is aimed at a workpiece (such as wood or a rough-coated surface) that does not have a reflective surface. • Do not use on materials, such as sheet steel, that have shiny, reflective surfaces. The reflective surface could reflect the beam back at the operator. Be aware that laser light reflected off of a mirror or any other reflective surfaces can also be dangerous. • Always turn the laser generator off when it is not in use. Leaving the tool on increases the risk of someone inadvertently staring into the laser's beam. • Always wear laser-protective reflective surfaces labels _, CAUTION: cuts. eyewear when working always follow the instructions product toward any on or near contained in this manual when using this laser. Use of this feature in any manner other than which is directed in this manual may result in a hazardous radiation exposure. 21228 Manual Revised 08-0307 Page 4 WORK AREA SAFETY Keep your work area clean and well lit. Do not leave tools or wood scraps on the saw while it is in operation. Cluttered workbenches and dark areas invite accidents • Do not operate power tools in explosive environments, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes. • Keep children and bystanders and visitors away while operating tool. Distractions can cause you to lose control. • Make your workshop childproof with padlocks tools away when they are not in use. • Make sure the work area has ample lighting so you can see the work, and that there are no obstructions that will interfere with safe operation. a power and master switches. Lock PERSONAL SAFETY • Know your power tool. Read this operator's manual carefully. Learn the compound miter saw's applications and limitations, as well as the specific, potential hazards related to this tool. • Stay alert, watch what you are doing, and use common operating a power tool. • Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. • Dress properly. Do not wear loose clothing or jewelry. Pull back long hair. Keep your hair, clothing and gloves away from moving parts. Loose clothing or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided. • Avoid accidental starting of tools. Be sure switch before plugging the tool into a power source. • Remove adjusting keys or blade wrenches before turning the tool "ON." A wrench that is left attached to a rotating part of the tool may result in personal injury. • De not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. • Always secure your work. Use clamps or a vise to hold work whenever practical. It is safer than using your hand and frees both hands to operate the tool. • Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. • Never stand on tool. Serious injury could occur if the tool is tipped blade is accidentally contacted. 21228 Manual Revised 08-0307 sense when is in "OFF "position or if the Page 5 TOOL USE AND CARE SAFETY _, WARNING: Be sure to read, understand, and follow all safety rules and operating instructions in this manual before using this tool. Failure to do so may result in electric shock, fire, and/or serious personal injury. • Always use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • De not force the power tool. Use the correct tool for your application. The correct tool will do the job better and more safely at the rate for which it is designed. • De not use the tool if switch does not turn it "ON" or "OFF." Any tool that cannot be controlled with the switch is dangerous and must be repaired. • Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. • Never leave the tool running. Always comes to a complete stop. • Store idle tools out of the reach of children and other untrained Tools are dangerous in the hands of untrained users. • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. • Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. • Use only accessories that are recommended for the tool being used. Accessories that may be suitable for one tool may become hazardous used on another tool. turn it off. Do not leave the tool until it persons. • Never cut metals or masonry products with this tool. This miter saw is designed for use only on wood and wood-like products. • Keep blade guards in place and in good working ELECTRICAL _, WARNING: when order. SAFETY Do not permit fingers to touch the terminal or plug when installing or removing the plug from an outlet. • To reduce the risk of electric shock, double insulated tools are equipped _Groun_ding pil _c_ with a polarized plug (one blade is wider than the other). This plug will fit C. Outlet Box in a polarized outlet only one way. If the t_ Cover of Grounded Grounding Means plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. 21228 Manual Revised 08-0307 Page 6 • Double insulation eliminates the need for the three-wire grounded power cord and grounded power-supply system. Applicable only to Class II (doubleinsulated) tools. This compound miter saw is a double insulated tool. _, WARNING: precautions Double insulation does not take the place of normal safety when operating this tool. • Before plugging in the tool, be sure that the outlet voltage supplied is within the voltage marked on the tool's data plate. Do not use "AC only" rated tools with a DC power supply. • Avoid body contact with grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded while using the tool. • Do not expose power tools to rain or wet conditions or use power tools in wet or damp locations. Water entering a power tool will increase the risk of electric shock. This tool is intended for indoor use only. • If operating a power tool in damp locations is unavoidable, always use a ground-fault circuit interrupter to supply power to your tool. Always wear electrician's rubber gloves and footwear in damp conditions. • Inspect tool cords for damage. Have damaged tool cords repaired at a Sears Service Center. Be sure to stay constantly aware of the cord's location and keep the cord well away from the moving blade. • Do not abuse the cord. Never use the cord to carry the tool by or to pull the plug from the outlet. Keep the cord away from heat, oil, sharp edges, and moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. EXTENSION CORDS Use a proper extension cord. Make sure that extension cords are in good condition. When using an extension cord, be sure to use a cord heavy enough to carry the drawn current needed by the compound miter saw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. The table on the following page shows the correct size to use, depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge: the smaller the gauge number, the heavier the cord. • Be sure extension cords are properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect extension cords from sharp objects, excessive heat, and damp or wet areas. • Use a separate electrical circuit for power tools. This circuit must not be less than #6 wire and should be protected with a time-delay fuse. Before connecting the tool to the power line, make sure the switch is in the "OFF" position and the electric current is rated the same as the current stamped on the motor nameplate; running at a lower voltage will damage the motor. 21228 Manual Revised 08-0307 Page 7 Recommended size of extension cords Volts Amperage More than rating Not more than 120v 240v Minimum Total length of the extension 25ft. 50ft. 50ft. 100ft. cord 100ft. 200ft. Gauge for the extension 150ft. 300ft. cord (AWG) 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not recommended ,& WARNING: Ensure that the power-supply outlet in question is properly grounded. If not certain, have a licensed electrician check the outlet. ,_ WARNING: To avoid electrical use proper circuit protection. SAFETY SYMBOLS hazard, fire hazards, or damage to the tool, FOR YOUR TOOL The label on your tool may include the following V ........................................... Volts A .......................................... Amps Hz ......................................... Hertz W .......................................... Watts Min ....................................... Minutes '_ Alternating ....................................... ........................................ symbols: current Direct current no ........................................ No-load speed [] Class II construction, ......................................... Double Insulated .../min .................................... Revolutions _, Indicates DANGER, WARNING or CAUTION: ATTENTION! Your safety is involved! ........................................ SERVICE or Strokes per minute SAFETY • If any part of this saw is missing or should break, bend, or fall in any way; or should any electrical component fall to perform properly: shut off the power switch, remove the plug from the power source, and have the missing, damaged or failed parts replaced before resuming operation. • Tool service must be performed only at a Sears Parts and Repair Center. Service or maintenance performed by unqualified personnel could result in a risk of injury. 21228 Manual Revised 08-0307 Page 8 When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SAFETY RULES FOR MITER SAWS • Know your power tool. Read the operator's manual carefully. Learn the applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury. • Always firmly clamp or bolt your miter saw to a secure, stable workbench table at approximately hip height. • Be sure that all adjustments • Always make sure that the miter table and saw arm are locked in position before operating your saw. Lock the miter table by securely tightening the miter-lock knob. Lock the saw arm by securely tightening the bevel-lock knob. • Use the hold-down whenever possible. • Be sure that the blade path is free of nails. Always carefully and remove all nails before cutting. • Always • Never start the saw with the blade touching • Always • Support long workpieces when cutting to minimize the risk of the blade pinching or kickback. The saw may slip, walk, or slide while cutting long or heavy boards. • Never use a length-stop • Never hold onto or bind the free end of the workpiece • If a work clamp and a length stop are used together, they must both be installed on the same side of the saw table to prevent the saw from catching the loose end and kicking up. • Never cut more than one piece at a time. Do not stack more than one workpiece on the worktable at a time. • Avoid awkward operations and hand positions where a sudden slip could cause your hand to move into the blade. Always make sure that you have good balance. Never position your saw on the floor or operate it while in a crouched position. • Never stand or have any part of your body in line with the path of the blade. • Only use the correct blades. Use the right blade size, style, and cutting speed for the material being cut and the type of cut. De not use blades with incorrect size holes. Never use blade washers or blade bolts that are clamp or are secure before making a cut. (included) to secure the workpiece inspect lumber be sure that the blade clears the workpiece. the workpiece. allow the motor to come up to full speed defective or incorrect. 21228 Manual Revised 08-0307 before starting a cut. on the free end of a clamped The maximum blade capacity workpiece. in any operation. for this saw is 10 inches. Page 9 • Always keep blades clean, sharp, and with the sufficient minimize stalling and kickback. set. Sharp blades • Do not use dull or damaged cause kickback. • Do not remove the saw's blade guards. • Never operate the saw with any guard or cover removed. guards are operating properly before each use. • Never hold with your hands a workpiece that is too small to be clamped. Always keep your hands clear of the "no hands" zone. • Never perform any operation freehand. Always place the workpiece to be cut on the miter saw table and position it firmly against the fence as a backstop. Always use the fence. • Never apply lubricants to the blade when it is running. Never use solvents to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. • Keep your hands away from the cutting area. Do not reach under the material being cut or in the blade's cutting path with your fingers or hand for any reason. Always turn the power off before reaching into the cutting area. blades. Bent blades can break easily or Make sure that all WARNING: The blade continues to turn after the power to the saw is turned off. To avoid possible serious injury, after releasing the trigger switch to cut power, allow the saw blade to stop rotating before raising the blade out of the workpiece. • Never reach behind, under, or within three inches of the blade and its cutting path with your hands or fingers for any reason. • Never, for any reason, touch the blade or other moving parts during use. • Do not turn the motor switch on and off rapidly. to loosen, which could create a hazard. Should and allow the saw blade to come to a complete from the power source and securely tighten the • Always turn off the saw before disconnecting it to avoid accidental starting when reconnecting the saw to a power supply. Never leave the saw unattended while connected to a power supply. • Keep the motor air slots clean and free of chips or dust. To avoid motor damage, the motor should be blown out or vacuumed frequently to keep sawdust from interfering with the motor ventilation. • Never lift this tool by gripping the cutting handle or the miter fence. This may cause misalignment. Always carry saw by holding the base or carry by the carrying handle after you have locked the saw arm in the DOWN position. _, WARNING: use of this product can generate dust containing known to cause cancer, birth defects examples of these chemicals are: • Lead from lead-based 21228 Manual Revised 08-0307 This could cause the blade this ever occur, stand clear stop. Disconnect the saw blade bolt. or other reproductive chemicals harm. Some paints. Page 10 • Crystalline • Arsenic silica from bricks and cement and other masonry and chromium from chemically-treated products. lumber. Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals: • Work in a well-ventilated area. • Work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. SAFETY RULES FOR THE USE AND OPERATION OF THE MITER SAW STAND • Always set up the miter saw stand on a hard, dry, flat, stable surface. • Be sure that the miter saw stand is fully opened and locked into the proper set-up position before mounting the miter saw to the tabletop assembly. • Follow all set-up • Always properly attach the miter saw to the stand. Do not attempt to use the miter saw stand with the miter saw until the tool is bolted securely to the tabletop assembly according to the instructions this operator's manual. • When using this miter saw stand with a miter that do not line up with the pre-slotted holes assembly, mount the power tool to a plywood then mount the plywood board and the miter • Always follow all safety rules and instructions in the operator's manual of the miter saw when operating a miter saw that is mounted to this stand. • Always be sure that there is sufficient space around the stand to safely operate the miter saw when setting up the miter saw stand and the miter saw. • Always check the miter saw stand and miter saw for damaged parts. Before further use of the stand or the tool, if any part is damaged, it should be carefully checked to determine if it will operate properly and perform its intended function. • Keep hands away from the cutting area. • Always use clamps or a vise to hold the workpiece, when practical. Using clamps or a vise to hold the workpiece is safer than using a hand. It also frees up both hands to operate the miter saw. • Avoid awkward operations and hand positions where a sudden cause a hand to move into the cutting area of the tool. • Never • Never sit, stand, or climb on this stand. It is not designed or constructed to accommodate this type of use. It could tip over, causing serious injury. • Do not store any items above or near the miter saw stand, especially when it is set-up with a power tool attached, or allow anyone to sit, climb or stand on the stand. • Never use this miter saw stand as a ladder or scaffold. instructions reach into the cutting 21228 Manual Revised 08-0307 in this operator's manual. saw that has mounting holes in the miter saw stand's tabletop mounting board (sold separately), saw to the tabletop assembly. slip could area of a tool. Page 11 ADDITIONAL RULES FOR SAFE OPERATION A_, WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/ OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. • Know your power tool. Read operator's manual carefully. Learn the applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury. • Always wear safety glasses or eye shields when using this saw. Everyday eyeglasses have only impact-resistant lenses; they are not safety glasses. All users and bystanders must wear eye protection that conforms to ANSI z87.1 • Protect • Protect your hearing. Wear appropriate personal hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • All visitors and bystanders must wear the same safety equipment operator of the saw should wear. • Inspect the tool cords periodically and, if damaged, have them repaired at your nearest Sears Service Center or other authorized service facility. Be aware of the cord's location when operating the saw. • Always check the tool for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. A guard or other part that is damaged should be properly repaired or replaced at a Sears Service Center. • Inspect • Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If someone borrows this tool, make sure they have these instructions also. your lungs. Wear a face mask or dust mask if the operation is dusty. that the and remove all nails from lumber before sawing. GLOSSARY OF TERMS FOR WOODWORKING • Arbor: The revolving shaft on which a blade or cutting tool is mounted. • Arbor Lock: Allows the user to stop the blade from rotating while tightening or loosening the arbor screw during blade replacement or removal. • Bevel Cut: A cutting operation 90 ° to the miter table. • Chamfer Cut: A cut removing a wedge from a block of wood so that the end (or part of the end) is angled at other than 90 ° . • Compound-Miter Cut: A cut made using both a miter angle and a bevel angle at the same time. • Cross Cut: A cutting 21228 Manual Revised 08-0307 operation made with the blade at any angle other than made across the grain of the workpiece. Page 12 • Flange: objects, A ring or collar on the end of a spindle or arbor that permits such as a blade, to be attached to it. other • Freehand Cut: Performing a cut without using a fence, miter gauge, fixture, work clamp, or other proper device to keep the workpiece from twisting or moving during the cut. Do not perform any operation free-hand. Use a clamp or vise wherever possible. • Gum: A sticky, sap-based • Kerr: The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut. • Kickback: residue from wood products. A hazard that can occur when the blade binds or stalls and throws the workpiece back toward operator. • Miter Cut: A cutting 90 ° to the fence. operation • No Hands Zone: The area between the marked lines on the left and right side of the miter-table base. This zone is identified by No Hands Zone symbols inside the marked lines on the miter table base. • Non-Through Cuts: Any cutting operation where the blade does not extend completely through the thickness of the workpiece. • Resin: • Revolutions Per Minute (RPM): The number of turns completed spinning object in one minute. • Saw Blade Path: The area over, under, behind, or in front of the blade, as it applies to the workpiece; that area which will be or has been cut by the blade. • Set: The distance that the saw blade tooth is bent (or set) outward face of the blade. A sticky, sap-based made with the blade at any angle other than substance Throat Plate: A plate inserted blade clearance. that has hardened. by a from the in the Miter Saw's table that allows for • Through Sawing: Any cutting operation through the thickness of the workpiece. where the blade cuts completely • Workpiece or Material: The item on which the cutting operation is performed. The surfaces of a workpiece are commonly referred to as faces, ends, and edges. _, WARNING: Your saw should never be connected to the power source when you are assembling parts, making adjustments, installing or removing blades, cleaning, or when it is not in use. Disconnecting the saw will prevent accidental starting, which could cause serious personal injury. 1. Open the carton and remove the saw by lifting it with its carrying _, IMPORTANT: cause misalignment Do not lift the miter saw by the cutting handle. handle, as this will of the saw arm to the saw base. 21228 Manual Revised 08-0307 Page 13 2. After lifting the saw out of the carton, place it on a flat, stable work surface with sufficient space to permit inspection of the saw. 3. The miter saw has been shipped with the saw arm locked in the DOWN position. To release the saw arm, press down slightly on the top of the saw arm and pull out the locking pin. 4. The saw arm is spring operated: hold the arm and allow it to rise slowly. The saw arm will automatically lift up and stay in the UP position to permit easy placement of material in the cutting area. 5. When the saw is not in use, the saw arm should be locked in the DOWN position. To lock the saw arm for transporting and for storage, press and hold down the saw arm to the lowest position, then push the locking pin in. 6. Inspect the saw carefully to make sure that no breakage occurred during shipping. 7. Check to make certain that all parts are accounted for. If any of the items listed are missing, or any breakage or damage has occurred, return the saw to your nearest Sears store or Craftsman outlet to have the saw replaced. or damage has CARTON CONTENTS/LOOSE PARTS ii Extension rails Miter-lock knob _f''h Saw Hold-down clamp L Blade Wrench 21228 Manual Revised 08-0307 Dust Bag Page 14 ID]_'_];;_i_e_] KNOW THE COMPOUND MITER SAW (Fig. 1) NOTE: Before attempting to use your saw, familiarize yourself with all of the features, operating instructions, and safety requirements. Your miter saw has a precision-built electric motor which should be connected only to a 120-volt, 60-Hz AC ONLY power supply (normal household current). Do not operate on direct current (DC): the large voltage drop will cause a loss of power and the motor will overheat. If the saw does not operate when plugged into a correct 120-volt, 60-Hz AC ONLY outlet, check the power supply. The saw comes with an 8-ft. power cord (no adapter needed). This Compound Miter 15.0 Amp motor: Provides On/Off trigger LaserTrac Saw has the following switch cutting Laser On/Off power and torque for fast cuts. and safety guide: features: lock-off provides button a clear indication of the line to be cut. switch Easy-to-read bevel and miter scales: miter cuts from 0 ° to 46 ° left and right with positive stops at 0 °, 15 °, 22.5 °, 31.6 °, and 45 ° for precise cuts. Bevel cuts from 0° to 46 ° left. Ergonomically designed handle with molded-in control and comfort when cutting. 3 Craftsman® smooth cutting comfort grip for maximum 10-in blades: 80-tooth, 100-tooth, and 120-tooth in all woods and wood-base materials. Die-cast aluminum and durable. Project ruler etched Hold-down clamp: clamp workpiece. upper blade guard, on right fence: table, fence, blades for and base: lightweight for quick reference. mounts on left or right side of fence to securely Durable, high-impact-plastic and laser cutting line. lower blade guard: allows view of workpiece Dust-extraction port: attaches to dust bag with the factory-installed adapter and to shop vacuum (not included) Easy-to-use adjustments; 1-1/4" knob and lever: for quick miter, bevel, and compound-miter no tools are needed. Permanently lubricated 100% ball bearings for long tool life and smooth operation. Saw arm locking pin: locks saw arm in down position when pushed in. Pull locking pin out to release saw arm. Arbor-lock _, button: WARNING: Remember stops arbor from rotating for easy blade changes. Do not allow familiarity with your saw to make you careless. that a careless fraction of a second 21228 Manual Revised 08-0307 is sufficient to inflict serious injury. Page 15 Fig. 1 26 3 _ 2 18 17 1. ON/OFF trigger switch 2. Horizontal, D-handle 3. Safety lock-off 4. Upper blade guard 5. Arbor-bolt 6. Dust-extraction 7. Saw blade 8. Laser aperture 9. Mounting rubberized button guard 16 / S 5 25 24 7 port 8 10 holes 11 12 13 10. Miter table 11. Miter-angle 14 scale 23 12. Throat plate 13. Miter-angle 14. Miter-lock indicator 18 knob 15. Clamp mounting 21 holes 16. Fence 17. Lower blade guard 18. Arbor-lock button 19. Laser ON/OFF 20. Saw-head switch locking 21. Bevel-angle pin 19 scale 22. Bevel lock 23. Bevel-angle 24. Extension 25. Hold-down indicator rails clamp _]" 20 26. Carry handle 22 Dust Bag L 21228 Manual Revised 08-0307 Page 16 PRODUCT Supply SPECIFICATIONS power 120V, 60Hz Rated current 15A No load speed 5500 RPM Saw blade size 10" (25.4 cm.) (80, 100, 120-tooth) Miter angle 46 ° left to 46 ° right Bevel angle 46 ° left CUTTING CAPACITIES Maximum Angle Setting Type of cut Miter Bevel Thickness Width Miter cut 45 ° 0o 2-5/8 in. 3-1/2 in Bevel cut 0o 45 ° 1-1/2 in. 5-1/2 in Compound cut 45 ° 45 ° 1-1/2 in. 3-1/2 in Cross Cut 0o 0o 2-5/8 in. 5-1/2 in NOTE: All cutting specifications will vary by blade type used, actual lumber size, and compound miter saw. All dimensions are approximate. 21228 Manual Revised 08-0307 Page 17 KNOW THE MITER SAW STAND (Fig. 2) Before attempting to use the Miter Saw Stand, become operating features and safety requirements familiar with all of its Fig. 2 4 1. Spring-Loaded Locking 6. Rubber Foot Pads Pin 2. Notch 7. Tabletop Assembly 3. Tabletop-Assembly 4. Chrome Clamping Extension 5. Carrying/Locking Knobs Bars 8. Table Assembly 9. Base Support Supporting Bar Bar Handle UNFOLDING AND SETTING UP THE MITER SAW STAND 1, 2, After taking the Miter Saw Stand out of carton, place it flat on the floor, as shown (Fig. 3). Fig. 3 Hold the red Locking/Carrying Handle (5) and the right side of the Table Assembly (7), and unlock the red Locking/Carrying Handle (5) by pulling the handle towards the operator until the stand is positioned as shown in Fig. 4. 21228 Manual Revised 08-0307 Page 18 3. Grasp the other bar and lift the Tabletop Assembly, 'Fig. _4 as shown in Fig. 5. F_ig. I 4. Continue to lift the Tabletop Assembly floor, as shown in Fig.6. while the Base remains in place on the 5. Continue to lift the Tabletop Assembly until it is completely 6. Hold the Base Bar Legs (as shown) by placing a foot on the Base Bar. Pull the Tabletop Assembly straight up until the Chrome Extension Bars attached to the Tabletop Assembly (4) are fully extended. Be sure that the Chrome Extension Bars lock in place (Fig. 8). 7. With one foot still on the Base Bar, grasp the Support Bar (8) and pull it up until the Chrome Extension Bars are also fully extended and lock in place. Pull the legs further apart to form an "X" (Fig. 9). 21228 Manual Revised 08-0307 vertical (Fig. 7). Page 19 8. With one foot still on the Base Bar, lower the Tabletop Assembly onto the Support Bar (8), while making sure that the Support Bar is placed into the Notch (Fig. 10). 9. Pull the Spring-Loaded Locking Pin back, so that the Support Bar and Tabletop groove fit together securely, and then release the Spring-Loaded Locking Pin so that the Tabletop locks into position (Fig. 11). 10. To change the width of the Tabletop Assembly working area, turn the two Clamp Knobs clockwise to unlock them, as shown in Fig. 12. Fig. 11 11. After loosening the Clamp Knobs (Fig. 13), adjust the Tabletop Assembly to the desired position to mount the power tool, as shown in Fig. 13 and 14. 12. Be sure that, after adjusting the width of the Tabletop Assembly, the two Clamping Knobs are locked: turn them until they are securely tightened (Fig. 15). Fig. 13 Fig. // Fig. 15, _ / J, 21228 Manual Revised 08-0307 Page 20 MOUNTING THE MITER SAW TO THE STAND (Fig. 16) 1. Check the Miter Saw for the number of mounting Fig. 16 holes and their locations. 2. Choose the corresponding on the Tabletop Assembly Saw Stand. 3. Change the width of the Tabletop Assembly, if necessary, to accommodate the Miter Saw. To change the width of the Tabletop Assembly, see Figs. 10 through 15 in Unfolding and Setting up the Miter Saw Stand. 4. Place the Miter Saw on the Tabletop Assembly, align the mounting holes in the Miter Saw with the holes on the Tabletop Assembly, and use the bolts and nuts (included) to connect them, as shown in Fig. 16. 5. When using this miter saw stand with a miter saw that has mounting holes that do not line up with the pre-slotted holes in the Tabletop Assembly, mount the power tool to a plywood mounting board (sold separately), then mount the plywood board and the miter saw to the Tabletop Assembly. FOLDING THE MITER hole locations of the Miter SAW STAND FOR STORAGE (Refer to Figs. 3 to 15) 1. Remove the Miter Saw from the Miter Saw Stand. 2. Loosen the Miter Saw Stand Clamping 3. Fully extend the Tabletop Assembly 4. Pull back on the Spring-Loaded Locking from the Tabletop groove (Fig. 11). 5. With one foot on the Base Bar, raise the Tabletop Assembly vertical position. 6. Close up the legs of Miter Saw Stand and push down on the Chrome Extension Bars until they are fully lowered. 7. Lower the Tabletop Assembly. 8. Use the yellow Locking/Carrying Legs together. _, WARNING: Knobs (Fig. 15). and re-tighten the Clamping Knobs. Pin and remove the Support Bar to the upright, Handle to join the Tabletop Assembly and To reduce the risk of injury, always unplug a tool before attaching or removing accessories recommended accessories. 21228 Manual Revised 08-0307 or making adjustment. Only use specifically Page 21 SETTING UP THE MITER SAW Installing the dust bag (see Fig. 17) Place the bag's neck opening dust-extraction port. Emptying equipped to empty from the a suitable to empty Fig. 17 Dust bag around the ust extraction the dust bag The dust bag is with a zipper to make it easy the bag. Remove the dust bag dust extraction port, hold it over receptacle, and unzip the bag its contents. Use with a shop vacuum An adapter (adapter sold separately) permits a shop vacuum to be attached to the dustextraction Releasing Fig. 18 port. and locking the saw head 1. Gently press and hold down head. Pull out the Saw-head pin to release the saw head. head should freely move up (see Fig. 18). the saw locking The saw and down 2. Place the saw head at the lowest position. Insert the Saw-head locking pin to lock the saw head for transporting and storage. Fig. 19 Removing _, Arbor bolt the blade (see Fig. 19) WARNING: To reduce the risk of Outer flange injury, always unplug the tool before removing and installing a blade. Arbor 1. Unplug the saw. 2. Release and raise the saw head. 3. Remove the upper screw on the arbor-bolt guard (Fig. 1, item 5) by turning it counter-clockwise with a screwdriver. Inner flange Blade 4. Lift and hold up the lower blade guard (Fig, 1, item 17) and rotate the arborbolt guard to expose the threaded arbor bolt. 5. Press and hold the arbor-lock button (Fig. 1, item 18) then rotate the blade with the blade wrench (included) while depressing the arbor-lock button until the blade is locked in position. 6. 7. Use the wrench to turn the arbor bolt clockwise and remove the arbor bolt. Remove the outer flange and the blade. Wipe the flanges and the arbor to remove any dust and debris. 21228 Manual Revised 08-0307 Page 22 Installing the blade 1. Unplug the saw. 2. Ensure that the inner flange is properly 3. Match the arrow on the blade with the arrow on the upper blade guard. Make sure that the blade teeth are pointing downward. Install the selected blade by sliding the blade into the upper blade guard and then placing the blade into position on the arbor. 4. Install the outer flange. _, WARNING: 5. Press and hold the arbor-lock button and use the wrench supplied to turn the arbor bolt counter-clockwise until the lock engages. Securely tighten the arbor bolt. 6. Rotate the arbor-bolt guard into position, and use the wrench to securely tighten the bolt by turning it clockwise. Remove and store the wrench in a safe place. 7. Make sure that the arbor-lock rotate freely. 8. Lower the saw head, and check the clearance miter table. The blade should rotate freely. Installing Make sure the flat side of the flange is placed against the blade. extension button is released, so that the blade will between the blade and the rails Fig. 20 The extension rails support long workpieces during cutting operations. (Fig. 20) 1. installed. Insert both ends of an extension rail through the holes on the outside the Miter Saw base. of 2. Tighten the knob that locks the extension rail in place. Make sure that the extension rails do not move. _, WARNING: To avoid possible injury, disconnect the tool's plug from the power source before performing any assembly, adjustment, or repair. _, WARNING: Do not use thin-kerr blades. Thin-kerf blades can deflect contact and the guard, which can cause injury to the operator. ADJUSTING THE BLADE Squaring the blade to the fence (Fig. 21 and Fig. 22) WARNING: causing serious Failure to unplug your saw could result in accidental injury. 1. Unplug the saw. 2. Set the bevel and miter angles to 0° 21228 Manual Revised 08-0307 starting, Page 23 3. Lower the saw arm and lock it into the DOWN position. 4. Using a square, place the heel of the square against the blade, and the rule of the square against the fence. NOTE: Be sure to rest the square against the body of the blade and not against the teeth of the blade. 5. If the blade is not 90 ° to the fence, loosen the four fence-locking nuts. Adjust the fence 90 ° to the blade. When blade is 90 ° square to fence, re-tighten the two fence-locking nuts. \ Fig. 22 \ SQUARING THE BLADE TO THE MITER TABLE: 0° Bevel, 0 ° Miter (Fig. 23 and Fig. 24) ,_ WARNING: Failure to unplug your saw could result in accidental causing serious injury. starting 1. Unplug the saw. 2. Set the bevel and miter angle scales to 0° and lock them in place. 3. Lower the saw arm and lock it into Fig. 23 _ ,/ ........ '! the DOWN position. 4. Place a square on the miter table with the rule against the table and heel of the square against the saw blade. de 90° Square to Miter Table Fig. 24a \ NOTE: Be sure to rest the square against the body of the blade and not against the teeth of the blade. 5. If the blade is not 90 ° square with the miter table, perform steps 6 and 7, below. 6. Loosen the bevel-lock knob, turn it counterclockwise, square the blade to the table, and pull out the bevel 0°locking bolt; you may need to move the saw arm left or right by hand. (Fig. 24) 21228 Manual Revised 08-0307 Page 24 7. When the angle is set, engage the lock bolt and tighten the bevel-lock knob. Fig. 24b ADJUSTING THE BLADE TO THE MITER TABLE: 45 ° Bevel, 0 ° MITER (Fig. 25 and Fig. 26) WARNING: Failure to unplug your saw could result in accidental starting causing serious injury. 1. Unplug the saw. 2. Raise the saw arm. 3. Set the bevel-angle scale to 45 ° . The miter scale should be on 0°. Lower and lock the saw arm into Adjustable nut Fig. the DOWN position. 4. Place a square on the miter table with the rule against the table and heel of the square against the saw blade. NOTE: Be sure to rest the square against the body of the blade and not against the teeth of the blade. 5. If the blade is not 45 ° square with the miter table, perform steps 6 through 8. 6. Loosen the 45 ° lock nuts with a hex wrench. 7. Loosen the bevel-lock knob, turn it counterclockwise, and adjust the blade to 45 ° by adjusting the set screws clockwise or counterclockwise Blade 45° Square to Miter Table 'Fig. 26 with the hex wrench. You may need to move the saw arm left or right by hand while turning the set screw. 8. When the angle is set, tighten the set screws and the bevel-lock knob. Miter adjustment 1. Unplug the saw. ,_ WARNING: causing serious Failure to unplug your saw could result in accidental starting injury. 2. Lock the saw head in the DOWN position, loosen the miter-lock knob, and depress the miter-lock lever. 3. Hold the cutting handle firmly to rotate the miter table to any desired angle. The most common angle settings have positive stops: 0°, 15 °, 22.5 °, 31.6 °, and 45 °. 4. Tighten the miter-lock 21228 Manual Revised 08-0307 knob and release the saw head. Page 25 Miter-angle indicator 1. Unplug the saw. ,_, WARNING: adjustment Failure to unplug your saw could result in accidental causing serious injury. 2. (if necessary) starting Place the miter table at the zero position, making sure the miter-lock knob is securely tightened. 3. 4. Loosen the miter-angle indicator screw and adjust the indicator to the "0" mark on the miter scale (see Fig. 27). Miter scale Indicator screw Tighten the miter-angle indicator screw. Bevel adjustment 1. Unplug the saw. _lk WARNING: Failure to unplug your saw could result in accidental causing serious injury. starting 2. Loosen the bevel lock (Fig. 28) by turning it counter-clockwise 3. Tilt the saw head to the desired angle as indicated on the bevel scale. The Bevel igle indicator blade can be positioned at any angle, from a 90 ° straight cut (0 ° on the scale) to a 46 ° left bevel. 4. Tighten the bevel lock to secure the saw head. THROAT PLATE SLOT (Fig. 29) The throat plate was cut (slotted) factory for a 0 ° bevel/miter cut. at the The first cut you will make with the saw will be to increase the slot in the throat plate by setting the bevel scale to 46 ° and making a cut. See the Operation section of this manual for cutting instructions, _, WARNING: Read all operating this cut to avoid injury. instructions and warnings before performing PIVOT ADJUSTMENTS NOTE: These adjustments were made at the factory, and under normal circumstances do not require readjustment. Saw-Arm Travel Pivot Adjustment: Your saw arm should rise (travel) completely 21228 Manual Revised 08-0307 to the up position without assistance. Page 26 _, WARNING: To avoid risk of personal injury, if your saw arm does not rise by itself or if there is play in the pivot joints, have your saw serviced Service Center before using. Bevel-Pivot at a Sears Adjustment: Your miter saw arm should bevel easily by loosening tilting the saw arm to the left. the bevel-lock knob and WARNING: To avoid risk of personal injury, if movement is tight or if there is play in the bevel pivot, have your saw serviced at a Sears Service Center before using. [e] ",,1 =1-'?,_'1 | [e]_ _1_ WARNING: side shields. To reduce the risk of injury, wear safety goggles _1_ WARNING: Before each use, check that the blade is free from cracks, loose teeth, missing teeth, or any other damage. or suspected. Do not use if damage _[_ WARNING: Always wait for the blade to stop completely, before changing accessories or making adjustment. Moving or glasses with is noticed and unplug the tool the Miter Saw 1. Lift the Miter Saw only when the saw is OFF, the plug is removed from the power-supply outlet, and the saw head is locked in the DOWN position. 2. To avoid damage, never carry the Miter Saw by the cutting 3. Always Mounting handle. carry the saw by the base or the Carry Handle. the Miter Saw To prevent the tool from sliding, falling, or tipping during operation, the Miter Saw can be mounted to a supporting surface, such as a level, sturdy worktable or bench. 1. Unplug the saw. 2. Position the Miter Saw on a table or workbench crosscutting long workpieces. 3. To mount the Miter Saw, insert fasteners through the four holes in the base of the Miter Saw and use the fasteners to secure the saw to the table or bench. Selection to allow adequate room for of Desired Angle Follow the steps in "MITER ADJUSTMENT" A[_ WARNING: and "BEVEL ADJUSTMENT." The throat plate (see Fig. 1, item 12) is factory-cut only for a 0° bevel cut; the first cut made with the tool in the 46 ° bevel position wider slot on throat plate. will create a _1, WARNING: Always make sure that the arbor-lock button is released, so that the blade will rotate freely. _l_ WARNING: Make sure that the Saw-head locking pin is loose and that the saw head moves freely up and down. Ensure that all clamps and locks are tight, 21228 Manual Revised 08-0307 Page 27 in place, and that there is no excessive movement Selection of Miter Saw parts. of workpiece 1. Be cautious with pitchy, knotty, wet, or warped workpieces. are likely to create pinching conditions. 2. Workpieces 3. Before cutting, 4. This tool is recommended Support _, These materials that bow and pinch may result in the saw blade kicking back. inspect for and remove any nails from the workpiece. only for cutting wood and wood-like materials. the workpiece WARNING: Never use the help of another person as a substitute for a table extension or as support for a workpiece that is longer or wider than the basic miter table. Never have another person help to feed, support, or pull the workpiece instead of using table extensions. • Use the fence. Align the workpiece flush against the fence. This will help to eliminate the tendency of the blade teeth to bind. The fence can be used to support miter, bevel, and compound cuts. • Use the workpiece clamp The work piece clamp fits into the clamp mounting holes on the back of the fence. Securely clamp the workpiece to the miter table. (See Fig. 30.) Clamping wide workpieces When cutting wide workpieces (such as 2-in. x 8-in. boards), the boards must be clamped with the hold-down clamp provided or a C-clamp (sold separately). Fig. 30 z<_x workpiece ' ded) A_, CAUTION: Pay attention to the position of your body and hands. Proper positioning of your body and hands when operating the miter saw will make cutting easier and safer. Never place hands near the cutting area. Aligning the blade for the cut _, WARNING: Do not look into the laser line. • Do not aim the laser line at people or animals. • Do not use the laser line on highly reflective from reflected light. • Only have the laser repaired by qualified • Do not insert hard objects • Clean the laser with a soft, dry brush. 1. Before starting a cut, draw the desired cut line on the workpiece. 21228 Manual Revised 08-0307 materials because of the hazard service technicians. into the laser lens. Page 28 2. Press the laser ON/OFF switch forward to turn on the laser. 3. Align the left side of laser line with the right side of cut line. The blade will cut the line marked on wood piece. NOTE: The laser adjustment has already been made at the factory. The left side of the laser line aligns with the right side of the blade. Align the marked cutting line with the left side of the laser line (Fig.31). Pay attention to body and hand positions. Proper positioning of the body and hands when operating the Miter Saw will make cutting easier and safer. Never place hands near the cutting area. Fig. 32 Start the Compound Miter Saw Safety lock-off button _, WARNING: Always hold the cutting handle firmly, because the starting and stopping action of the motor may cause the handle to move up or down slightly. 1. Plug the Compound Miter Saw into a power-supply outlet. 2. Unlock the saw head and allow it to Cutting handle Trigger rise to the UP position. 3. Push the safety lock-off button while squeezing the ON/OFF trigger switch to turn the tool ON. (See Fig. 32.) 4. Wait until the blade reaches full speed before lowering the head and making a cut. See instructions Cuts, below. for Crosscuts, _, Do not use the saw without the lower blade guard. The lower WARNING: Bevel Cuts, Miter Cuts, and Compound-Miter blade guard is attached to the saw for your protection. Should the lower blade guard become damaged, do not use the saw until the damaged guard has been replaced. Check t he lower blade guard regularly, making certain that it is in proper working order. WARNING: Always keep hands and fingers away from the cutting area. Any part of the body coming into contact with a moving blade will result in serious injury. Stop the Miter Saw and remove the workpiece 1. After completing a cut, release the ON/OFF trigger switch and turn the laser ON/OFF switch off. 2. Allow the saw blade to come to a complete stop. 21228 Manual Revised 08-0307 Page 29 3. Gently raise the saw head and remove the workpiece. Do not remove the workpiece from the sawing plate until the blade has stopped rotating. Ensure that the lower blade guard can easily close. 4. Unplug the tool. 5. Remove loose or scrap pieces. CROSSCUTS (Fig 33 and Fig 34) A crosscut is a cut made across the grain of the workpiece. A straight crosscut is a cut made with the miter table set in the 0° position. Fig. 33 Miter crosscuts are made with the miter table set at an angle, left or right that is not 0°. To Crosscut With the Miter Saw 1. Unplug the saw. _, WARNING: Failure to unplug the saw could result in accidental causing serious injury. starting, Fig. 34 2. Push in the locking pin to lock the saw arm in the DOWN position. 3. Loosen the knob and depress miter-lock lever. 4. Firmly hold the base of the saw arm and use it to rotate the miter the table, while also holding the saw base steady. 5. Quickly locate 0°, 15 °, 22.5 °, 31.6 ° and 45 °, left or right, by the stops or clicks at these angle settings. 6. When the miter angle is set, tighten the miter-lock 7. Pull out the locking 8. Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of the board is against the fence, the board could collapse on the blade at the end of the cut and jam the blade. 9. Plug the saw into a power supply. knob. pin to release the saw arm. 10. Turn on the Laser with the Laser ON/OFF switch. 11. Align the "red laser line" to touch the right edge of the cut line marked the workpiece. 12. Use the hold-down and fence. 21228 Manual Revised 08-0307 clamp to secure the workpiece on against the saw table Page 30 13. When cutting long workpieces, support the opposite end of the workpiece with a roller stand or with another work surface that is level with the saw table. ,_ WARNING: To avoid serious personal injury, always securely tighten the miter-lock knob before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut. _, CAUTION: Never use another person as an additional support for a workpiece that is longer or wider than the basic saw table, or to help feed, support, or pull the workpiece. ,_ WARNING: To avoid serious personal injury, always keep hands outside the "No Hands Zone" marked on the saw table: at least 3 inches (7.6 cm) from the blade. Also, never perform any cutting operation "freehand" (i.e., without holding the workpiece against the fence); the blade could grab the workpiece, causing it to slip and twist. 14. Before turning on the saw, perform a test of the cutting operation by lowering the saw arm to make sure that no problems will occur when the cut is made. 15. To turn on the saw, push the safety-lock button in with the thumb while squeezing the On/Off trigger switch located under the handle. Allow several seconds for the blade to reach maximum speed. 16. Slowly lower the blade into and through the workpiece. 17. Release the safety lock and the trigger switch, and turn off the laser switch. Allow the saw blade to stop rotating before raising the blade out of the workpiece. BEVEL CUTTING (Fig. 35) A bevel cut is a cut made across the grain of the workpiece with the blade at an angle to the workpiece. A straight bevel cut is made with the miter table set in the 0° position and the saw arm set at a bevel angle between 0 ° and 46 ° To Bevel Cut with the Miter Saw 1. Unplug the saw. _, WARNING: Failure to unplug the saw could result in accidental starting, causing serious 2. Make sure that the miter table is at 0° and locked, table lock is locked and secured in position. ,_ WARNING: To avoid serious personal injury. and check that the miter- injury, always securely tighten the miter-lock knob before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut. 21228Manual Revised 08-0307 Page31 3. Pull out the locking pin to release the saw arm. 4. To make a bevel cut, loosen the bevel-lock counter clockwise. 5. Tilt the saw arm to the desired bevel angle as indicated on the bevel scale. The blade can be positioned at any angle, from a 90 ° straight cut (0 on the scale) to a 46 ° left bevel. 6. Tighten _, WARNING: the bevel-lock knob by turning the knob knob. Always tighten the bevel-lock knob to secure the saw arm in its position. 7. Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of the board is against the fence, the board could collapse on the blade at the end of the cut and jam the blade. 8. Plug the saw into a power supply. 9. Hold the saw handle and use your index finger to turn on the laser switch by pushing it forward. 10. Align the red laser line to touch the right edge of the cut line marked on the workpiece. Turn off the laser. 11. Use the hold-down table and fence. clamp to secure the workpiece against the Miter Saw 12. When cutting long workpieces, support the opposite end of the workpiece with a roller stand or with another work surface that is level with the saw table. ,_ CAUTION: Never use another person as an additional support for a workpiece that is longer or wider than the basic saw table or to help feed, support, or pull the workpiece. ,_ WARNING: To avoid serious personal injury, always keep hands outside the "No Hands Zone," as marked on the saw table: at least 3 inches (7.6 cm) from the blade. Also, never perform any cutting operation "freehand" (i.e., without holding the workpiece against the fence); the blade could grab the workpiece, causing it to slip and twist. 13. Before turning on the saw, perform a trial of the cutting operation by lowering the saw arm to make sure that no problems will occur when the cut is made. 14. Turn on the laser switch.To turn on the saw, push the safety-lock button in with your thumb while squeezing the On/Off trigger switch located under the handle. Allow several seconds for the blade to reach maximum speed. 15. Slowly lower the blade into and through the workpiece. 16. Release the safety lock and the trigger switch, and turn off the laser switch. Allow the saw blade to stop rotating before raising the blade out of the workpiece. ,_, CAUTION: Always perform a "dry run" cut to determine if the operation being attempted is possible before power is applied to Miter Saw. 21228 Manual Revised 08-0307 Page 32 CUTTING BASE MOLDING (Fig. 36) Base moldings and many other moldings can be cut on a miter saw. The proper setup of the saw depends on base molding characteristics and applications, as described below. Perform practice cuts on scrap materials to achieve best results. 1. 2. Always make sure moldings rest firmly against the fence and table. Use holddown clamp provided, a crown molding vise, or C-clamps and place tape on the area being clamped to avoid marks on the workpiece. Reduce splintering by taping the cut area prior to making the cut. Mark the cut line directly on the tape. Fig. 36 Molding lying flat on miter table (before clamping) ¢_ Fence Meiteer i Molding standing (before clamping) up against fence ._ Fence Miter at 45 °, _ Bevel Miter Table 3. Splintering is typically due to incorrect blade style, dull blade, thinness of workpiece, or improperly dried wood. 4. Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of the board is against the fence, the board could collapse on the blade at the end of the cut and jam the blade. 5. Align the "red laser line" to touch the right edge of the cut line marked the workpiece. 6. Use the hold down clamp to secure workpiece 7. When cutting long workpieces, for the long workpieces. on against saw table and fence. pull out the extension rail for extra support NOTE: Always perform a dry run cut so you can determine if the operation attempted is possible before power is applied to miter saw. COMPOUND MITER CUTTING being (Fig. 37) A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of cut is used for decorative moldings, picture frames, and other fine joinery. To make this type of cut, the miter table must be rotated to the correct angle and the saw arm must be tilted to the correct bevel angle. Always take special care when making compound interaction of the two angle settings. miter miter cuts, due to the Adjustments of miter and bevel settings are dependent on one another. Each time the miter setting is adjusted, the effect of the bevel setting also changes. Each time the bevel setting is adjusted, the effect of the miter setting is changed. It may take several settings to obtain the desired cut. The first angle setting should be checked after setting the second angle, since adjusting the second angle affects the first. 21228 Manual Revised 08-0307 Page 33 Once the two correct settings for a particular cut have been obtained, always make a test cut in scrap material before making a finish cut in good material. To Make a Compound 1. Unplug the saw. ,_ WARNING: causing serious Miter Cut with the Miter Saw (Fig. 37) Failure to unplug the saw could result in accidental starting, injury. 2. Pull out the locking the saw arm. pin to release 3. Loosen the miter-lock Fig. 37 knob and depress the miter-lock lever to loosen the miter table. 4. Hold the base of the saw arm firmly and use it to rotate the miter table while holding the saw base steady. 5. The0 °,15 °, 22.5 °, 31.6 ° , and 45 ° , left and right settings are quickly identifiable with the stops at the angle settings. 6. When the desired miter-table setting ,_ WARNING: personal To avoid serious is achieved, tighten the miter-lock injury, always securely knob. tighten the miter-lock knob before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut. 7. To set the bevel angle, loosen the bevel-lock counter clockwise. knob by turning the knob 8. Tilt the saw arm to the desired bevel angle, as shown on the bevel scale. Bevel angles can be set from 0°to 46°left bevel. 9. When the saw arm has been set at the desired angle, securely bevel-lock knob. tighten the 10. Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of the board is against the fence, the board could collapse on the blade at the end of the cut and jam the blade. 11. Plug the saw into a power supply. 12. Hold the saw handle and use your index finger to turn on the laser switch by pushing it forward. Align the red laser line to touch the right edge of the cut line marked on the workpiece. Turn off the laser. 13. Use the hold-down and fence. clamp to secure the workpiece against the saw table 14. When cutting long workpieces, support the opposite end of the workpiece with a roller stand or with another work surface that is level with the saw table. _, CAUTION: Never use another person as an additional support for a workpiece that is longer or wider than the basic saw table, or to help feed, support, or pull the workpiece. 21228 Manual Revised 08-0307 Page 34 _, WARNING: To avoid serious personal injury, always keep hands outside the "No Hands Zone", as marked on the saw table, which is at least 3 inches (7.6 cm) from the blade. Also, never perform any cutting operation "freehand" (i.e. without holding the workpiece against the fence); the blade could grab the workpiece, causing it to slip and twist. 15. Make sure that there will be no obstructions to interfere with making the cut. 16. Turn on the laser switch. 17. To turn on the saw, push the safety-lock button in with your thumb while squeezing the On/Off trigger switch located under the handle. Allow several seconds for the blade to reach maximum speed. 18. Slowly lower the blade into and through the workpiece. 19. Release the safety lock and trigger switch, and turn off the laser switch. Allow the saw blade to stop rotating before raising the blade out of the workpiece. CUTTING COMPOUND MITERS To help make the correct settings, use the compound angle setting chart below. Since compound cuts are the most difficult to accurately achieve, plan carefully and make trial cuts in scrap material prior to making your required cut. COMPOUND-ANGLE SETTINGS FOR *Pitch of Side = Angle of side from vertical, POPULAR STRUCTURES Example: i.!_/ ,'//: *PITCH OF SIDE 3 4 7 8 O° M-45.00 ° B- 0.00 ° M-36.00 ° B- 0.00 ° M-30.00 ° B- 0.00 ° M-25.71° B- 0.00 ° M-22.50 ° B- 0.00 ° M-20.00 ° B- 0.00 ° M-18.00 ° B- 0.00 ° 5° M-44.89 ° B- 3.53 ° M-35.90 ° B- 2.94 ° M-29.91 ° B- 2.50 ° M-25.63 ° B- 2.17 ° M-22.42 ° B- 1.91 ° M-19.93 ° B- 1.71 ° M-17.94 ° B- 1.54 ° 10 ° M-44"56° B- 7.05 ° M-35"58° B- 5.86 ° M-29"62° B- 4.98 ° M-25"37° B- 4.32 ° M-22"19° B- 3.81 ° M-19"72° B- 3.40 ° M-17"74° B- 3.08 ° 15 ° M-44.01 ° B-10.55 ° M-35.06 ° B- 8.75 ° M-29.15 ° B- 7.44 ° M-24.95 ° B- 6.45 ° M-21.81 ° B- 5.68 ° M-19.37 ° B- 5.08 ° M-17.42 ° B- 4.59 ° 200 M-43.22 ° B-14.00 ° M-34.32 ° B-11.60 ° M-28.48 ° B- 9.85 ° M-24.35 ° B- 8.53 ° M-21.27 ° B- 7.52 ° M-18.88 ° B- 6.72 ° M-16.98 ° B- 6.07 ° 250 M-42.19 ° B-17.39 ° M-33.36 ° B-14.38 ° M-27.62 ° B-12.20 ° M-23.35 ° B-10.57 ° M-20.58 ° B- 9.31 ° M-18.26 ° B- 6.72 ° M-16.41 ° B- 7.50 ° 300 M-40.89 ° B-20.70 ° M-32.18 ° B-17.09 ° M-26.57 ° B-14.48 ° M-22.64 ° B-12.53 ° M-19.73 ° B-11.03 ° M-17.50 ° B- 9.85 ° M-15.72 ° B- 8.89 ° 350 M-39.32 ° B-23.93 ° M-30.76 ° B-19.70 ° M-25.31 ° B-16.67 ° M-21.53 ° B-14.41 ° M-18.74 ° B- 12.68 ° M-16.60 ° B- 11.31 ° M-14.90 ° B- 10.21 ° M-37.45° B-27.03 ° M-29.10 ° B- 22.20 ° M-23.86 ° B-18.75 ° M-20.25 ° B-16.19 ° M-17.60 ° B- 14.24 ° M-15.58 ° B- 12.70 ° M-13.98 ° B- 11.46 ° 450 M-35.26 ° B-30.O0 ° M-27.19 ° B-24.56 ° M-22.21 ° B-20.70 ° M-18.80 ° B-17.87 ° M-16.32 ° B- 15.70 ° M-14.43 ° B- 14.00 ° M-12.94 ° B- 12.62 ° 500 M-32.73 ° B-32.80 ° M-25.03 ° B- 26.76 ° M-20.36 ° B-22.52 ° M-17.20 ° B-19.41 ° M-14.91 ° B- 17.05 ° M-13.17 ° B- 15.19 ° M-11.80 ° B- 13.69 ° 40 ° 21228 Manual Revised 08-0307 i_ulvlo=, 5 ur _Juco 6 Page 35 *PITCH OF SIDE 3 4 i_ulviDcr_ ur _Juc_ 5 6 7 8 9 550 M-29.84 ° B-35.40 ° M-22.62 ° B-28.78 ° M-18.32 ° B-24.18 ° M-15.44 ° B-20.82 ° M-13.36 ° B- 18.27 ° M-11.79 ° B- 16.27 ° M-10.56 ° B- 14.66 ° 600 M-26.57 ° B-37.76 ° M-19.96 ° B-30.60 ° M-16.10 ° B-25.66 ° M-13.54 ° B-22.07 ° M-11.70 ° B- 19.35 ° M-10.31 ° B- 17.23 ° M- 9.23 ° B- 15.52 ° 650 M-22.91 ° B-39.86 ° M-17.07 ° B- 32.19 ° M-13.71 ° B-26.95 ° M-11.50 ° B-23.16 ° M- 9.93 ° B- 20.29 ° M- 8.74 ° B- 18.06 ° M- 7.82 ° B- 16.26 ° 700 M-18.88 ° B-41.64 ° M-13.95 ° B-33.53 ° M-11.17 ° B-28.02 ° M- 9.35 ° B-24.06 ° M- 8.06 ° B-21.08 ° M- 7.10 ° B- 18.75 ° M- 6.34 ° B- 16.88 ° 750 M-14.51 ° B-43.08 ° M-10.65 ° B-34.59 ° M- 8.50 ° B-28.88 ° M- 7.10 ° B-24.78 ° M- 6.12 ° B-21.69 ° M- 5.38 ° B- 19.29 ° M- 4.81 ° B- 17.37 ° 80 ° M- 9.85 ° B-44.14 ° M- 7.19 ° B-35.37 ° M- 5.73 ° B-29.50 ° M- 4.78 ° B-25.30 ° M- 4.11 ° B-22.14 ° M- 3.62 ° B- 19.68 ° M- 3.23 ° B- 17.72 ° 85 ° M- 4.98 ° B-44.78 ° M- 3.62 ° B- 35.84 ° M- 2.88 ° B-29.87 ° M- 2.40 ° B-25.61 ° M- 2.07 ° B- 22.41 ° M- 1.82° B- 19.92 ° M- 1.62 ° B- 17.93 ° 900 M- 0.00 ° B-45.00 ° M- 0.00 ° B- 36.00 ° M- 0.00 ° B-30.O0 ° M- 0.00 ° B-25.71 ° M- 0.00 ° B- 22.50 ° M- 0.00 ° B-20.00 ° M- 0.00 ° B- 18.00 ° Each B (Bevel) and M (Miter) Setting CUTTING CROWN MOLDING is listed to the closest 0.005 ° (Fig. 38) Your miter saw is ideal for cutting crown molding. In order to fit properly, crown molding must be compound-mitered with extreme accuracy. To fit flat against the ceiling and wall, the sum of the angles of the crown molding's two connecting surfaces must equal 90 ° Most crown molding has a high top rear spring angle (the section that fits flat against the ceiling) of 52 ° and a bottom rear spring angle (the section that fits flat against the wall) of 38 ° In order to accurately cut crown molding for a 90 ° inside or outside corner, lay the molding with its broad back surface flat on the miter table and against the fence. When setting the bevel and miter angles for compound miter cuts, remember that the settings are interdependent; changing one changes the other. Keep in mind that, since it is very easy for the angles of crown molding to shift slightly, all settings should be tested on scrap molding. Also, most walls do not have angles of precisely 90 ° , therefore, you will need to fine tune your settings. When cutting crown molding using this method, the bevel angle should be set at 33.9 o. The miter angle should be set at 31.6 ° either left or right, depending upon the desired cut for the application. See the following table for correct angle setting and correct positioning of the crown molding on the miter table. The settings in the table below can be used for cutting all standard (U.S.) crown molding with 52 °And 38 o spring angles. The crown molding is placed flat on the miter table, using the compound features of your miter saw. Always use the hold-down clamp, and place tape on the area being clamped avoid marks on the workpiece. 21228 Manual Revised 08-0307 to Page 36 Fig. 38 52° Ceiling Corner Outside Corner Left Side, Inside Corner Fence -- / Bottom Edge Against Fence = • Right Side, Inside Corner ..... \ utsid/_ MiternereCor ble COMPOUND BEVEL/MITER SETTINGS Bevel Setting Miter Setting Type of cut Inside corner 33.9 ° 31.6°Right - Left side 1. Position top of molding against fence. 2. Miter table set at RIGHT 31.6 ° 3. LEFT side of cut is finished Inside corner 33.9 ° 31.6°Left - Right side 1. Position top of molding against fence. 2. Miter table set at LEFT 31.6 ° 3. LEFT side of cut is finished Outside 33.9 ° 31.6°Left corner 1. Position top of molding against fence. 2. Miter table set at LEFT 31.6 ° Outside 31.6°Right corner piece. - Right side 1. Position top of molding against fence. 2. Miter table set at RIGHT 31.6 ° 3. RIGHT side of cut is finished 21228 Manual Revised 08-0307 piece. - Left side 3. RIGHT side of cut is finished 33.9 ° piece. piece. Page 37 CUTTING WARPED MATERIAL (Fig. 39 and 40) _, WARNING: To avoid kickback and to avoid serious personal injury, never position the concave side of bowed or warped material against the fence. When cutting warped material, be certain that the material to be cut is positioned on the miter table with the convex side against the fence, as shown in Fig. 35. If the warped material is positioned the wrong way, (Fig. 36), it will pinch the blade near the end of the cut. Fig. 39 Top View Fig. 40 Right I_vl V,_I Il i / _4l V,_I l [ll,_! ,_, WARNING: To ensure safety and reliability, all repairs - with the exception the externally accessible brushes -should technician at a Sears Service Center. be performed by a qualified of service ,_ WARNING: For your safety, ALWAYS turn off the switch and unplug the miter saw from the power source before performing any maintenance or cleaning. Electric tools are subject to accelerated wear and possible premature failure when they are used to work on fiber glass boats and sports cars, wallboard, spackling compounds, or plaster. The chips and grindings from these materials are highly abrasive to electrical tool parts, such as bearings, brushes, commutators, etc. Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compound or plaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jet. ,_, WARNING: Always wear safety goggles or safety glasses with side shields during power tool operations, also wear a dust mask. ROUTINE _. or when blowing dust. If the operation is dusty, MAINTENANCE WARNING: DO NOT at any time allow brake fluids, gasoline, petroleum- based products, penetrating oils, etc. to come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, which may result in serious personal injury. 21228 Manual Revised 08-0307 Page 38 Periodic maintenance allows for long life and trouble-free operation. A cleaning and maintenance schedule should be maintained. As a common preventive maintenance practice, follow these recommended steps: 1. Always unplug tool before 2. performing any maintenance operation. When work has been completed, of the tool over time. 3. Use clean, damp cloths to wipe the tool. 4. Check the state of all electrical when appropriate. 5. Keep the motor air openings free from oil, grease, and sawdust woodchips and store the tool in a dry place. 6. Be certain that all moving parts are well lubricated, exposure to damp and/or dirty conditions. clean the tool to allow smooth functioning cables and have repairs made particularly or after lengthy ,_ CAUTION: When cleaning the lower blade guard, unplug the saw from the power source to avoid unexpected startup. NOTE: Do not use solvents on the guard, as they may cause any plastic parts to become "cloudy" or brittle. REPLACEMENT OF CARBON BRUSHES (Fig. 41) Replacement brush sets are available through Sears Parts and Repair Centers. Replace both carbon brushes when either brush has less than 1/4 inch of carbon remaining. 1. Unplug the saw before inspecting replacing brushes. or 2. Open the back cover by loosening four screws. 3. Replace the carbon bushes and keep the brushes clean and sliding freely in their guide channels. the . NOTE: To reinstall the same brushes, make sure the brushes go back in the same way they came out. This will avoid a break-in period. 4. Install the back cover by replacing it and tightening the four screws, but do not over-tighten. The saw should be allowed to "RUN IN" (run at no-load without a blade) for 5 minutes before use, to seat the new brushes properly. ,_ WARNING: trigger switch While "running "on." in", do not tie, tape, or otherwise Hold the trigger switch "on" lock the by handZ NOTE: Do not use solvents on the lower blade guard, as they may cause any plastic parts to become "cloudy" or brittle. 21228 Manual Revised 08-0307 Page 39 SAWDUST Periodically, sawdust will accumulate under the worktable and base. This could cause difficulty in the movement of the worktable when setting up a miter cut. Frequently blow out or vacuum up the sawdust. A_, WARNING: Always wear safety goggles or safety glasses with side shields during power tool operations, wear a dust mask. or when blowing dust. If operation is dusty, also LUBRICATION All the motor bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal operating conditions; therefore, no further lubrication is required. PROBLEM PROBABLE CAUSE Electric hand brake has failed Brake does not stop blade within 6 seconds Motor brake overheated from use of defective or SUGGESTED CORRECTIVE ACTION Take saw for servicing Use a recommended blade wrong size blade or rapid ON/OFF cycling Arbor bolt is loose Saw not plugged in Retighten arbor bolt Check that all cords are plugged in Motor does not start Angle of cut inaccurate Fuse Check time delay fuse or circuit breaker Miter table unlocked Use miter-lock ADJUSTMENT Too much sawdust Vacuum or blow out dust. Wear under table Eye Protection! 21228 Manual Revised 08-0307 knob. See section Page 40 PROBLEM Cutting arm cannot fully raise, or blade guard cannot fully close Blade binds, jams, or burns wood PROBABLE CAUSE Parts failure Contact Sears Service Center Pivot spring not replaced properly after service Contact Sears Service Center Saw-head Check, adjust, and properly Laser line projection is hard to see 21228Manual locking pin not set properly saw-head Sawdust buildup Clean moving Improper operation "See OPERATION section" Dull blade Improper Warped Saw vibrates or shakes SUGGESTED CORRECTIVE ACTION locking set pin parts Replace blade blade blade Replace blade Replace blade Saw blade damaged Replace blade Saw blade loosened Tighten Saw not properly fastened down Fasten saw to stand, or table Workpiece not properly supported Properly support workpiece Light in work area is too bright Move the Miter Saw to the work area with proper light Saw dust on the laser lens Clean laser lens with a soft, dry brush Revised 08-0307 arbor bolt bench, or clamp Page41 Compound Miter Saw MODEL NUMBER 320.21228 Always mention the Model Number when ordering 21228 Manual Revised 08-0307 parts for this tool. Page 42 ",2'-_ a [,.1I1E_1iii No Name Quantity No Name Quantity 1 Screw 2 31 Spring washer 2 2 Motor cover 1 32 Screw 2 3 Screw 4 33 Screw 6 4 Brush 2 34 Lower handle 1 5 Brush spring 2 35 Cold clamp 1 6 Brush hold 2 36 Screw 3 7 Screw 4 37 Screw 1 8 Spring washer 4 38 Laser switch 1 9 Washer 4 39 Laser switch cap 1 10 Motor housing 1 40 Transformer 1 11 Rubber 1 41 Trigger 1 12 Wave wsher 1 42 Cord protector 1 13 Bearing 1 43 Cable plug 1 14 Armature 1 44 Upper handle 1 15 Stator 1 45 Washer 4 16 Washer 2 46 Spring washer 4 17 Spring washer 2 47 Screw 4 18 Screw 2 48 Carry handle 1 19 Fan baffle 1 49 Screw 2 20 Bearing 1 50 Binding 21 O-ring 1 51 Switch 1 22 Gear lock pin spring 1 52 Spring 1 23 Gear lock pin 1 53 Switch 24 Gear lock pin cap 1 54 Fixed guard 1 25 Screw 1 55 Needle bearing 1 26 Spring washer 1 56 C clip 1 27 Anti-fingertouch 1 57 Gear 1 28 Gear case 1 58 Gear washer 1 29 Exhaust port 1 59 Key 1 30 Washer 2 60 Arbor 1 boot 21228 Manual Revised 08-0307 plate post lock button 1 1 Page 43 No Name Quantity No Name Quantity 61 Bearing 1 91 Trunnion 1 62 Screw 2 92 Lock pin 1 63 Gear case cover 1 93 Rolled pin 1 64 Spring washer 2 94 Lock pin spring 1 65 Screw 2 95 Lock pin cap 1 66 Blade flange inner 1 96 Pivot shaft 1 67 Blade 1 97 Steel cable baffle ring 2 68 Blade flange outer 1 98 Torsion spring 1 69 Blade bolt 1 99 Spring bushing 1 70 Rivet 4 100 Laser carrier 1 71 Moving guard 1 101 Washer 2 72 Special screw 1 102 Spring washer 2 73 Cast center 1 103 Screw 2 74 Spring 1 104 Laser 1 75 Screw 1 105 Laser cover 1 76 Spring washer 1 106 Screw 1 77 Big washer 1 107 Screw 1 78 Moving guard plate 1 108 Spring washer 1 79 Plate guarding(small) 1 109 Washer 1 80 Plate guarding(big) 1 110 Lever pointer 1 81 Spring washer 2 111 Nut 2 82 Screw 2 112 Bolt 2 83 Shoulder 1 113 Screw 4 1 114 Cutting 1 115 Locknut 1 Screw 84 Linkage 85 Shoulder 86 Bevel lock handle 1 116 Big washer 1 87 Big washer 1 117 Turntable 1 88 Double stud 1 118 Screw 1 89 Socket 1 119 Spring washer 1 90 Bushing 1 120 Washer 1 Screw head screw 21228 Manual Revised 08-0307 insert 1 Page 44 No Name Quantity No Name 121 Miter pointer 1 138 Support 122 Clamp plate 1 139 Knob 1 123 Spring washer 2 140 Sunk screw 2 124 Screw 2 141 Miter scale board 1 125 Safety plate 1 142 Bolt 1 126 Spring washer 4 143 Base 1 127 Screw 4 144 Washer 4 128 Spring washer 2 145 Allen key head screw 4 129 Screw 2 146 Screw 1 130 Detent 1 147 Clamp 1 131 Detent button 1 148 Support 132 Lock bolt 1 149 Knob 133 Lock handle 1 150 Workpiece 134 Screw 1 151 Support 135 Lock handle cap 1 152 Knob 1 136 Blade spanner 1 153 Fence 1 137 Knob 1 21228 Manual Revised 08-0307 Quantity bar arm 1 1 1 knob pole 1 1 Page 45 Miter Saw Stand Stand MODEL NUMBER 320.21228 Always mention the Model Number when ordering 1 3 4 parts for this tool. S 6 7 8 9 11 18 15 44 41 39 S? 38 45 35 46 21228 Manual Revised 08-0307 Page 46 ",2'-_ a [,.1I1E_1iii No Name Quantity fixed worktable assembly 1 No Name Quantity 26 outter pole 4 27 limit position board 2 2 knob 2 28 plate 4 3 clamp ring 2 29 plate board 4 4 hexagon screw 2 3O Washer 2 5 moving table 1 31 screw M4x12 8 6 slide ring 2 32 spring cover 4 7 bolt M4x12 10 33 pole cover 2 8 gemel 11 1 34 lock device 1 9 bolt M4x24 4 35 screw M5x38 4 10 table pole 1 36 pole 1 11 screw 1 37 limit position 12 gemel 1 1 38 upper inner pole 1 13 nut M4 14 39 upper inner pipe 1 14 nut M8 9 4O washing 1 15 M4x12 pole 2 upper outer pole 1 41 spring A 1 16 cover 2 42 suport 1 17 upper gemel 4 43 hook 1 18 hex bolt M8x20 1 44 handle cover 1 19 screw 4 45 lower inner pole 1 20 nut M6 4 46 lower outter pole 1 21 inner pole 4 47 right foot 2 22 ring 4 48 left foot 2 23 gemel Bracket 4 49 nut M5 8 24 nut ring 2 50 screw M5x29 4 25 nut cover 2 M6x35 21228 Manual Revised 08-0307 ring Page 47 Your Home For expert troubleshooting and home solutions advice: °°wnww : • ge y o e.co For repair - in your home- of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-8oo-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.com www.sears.ca ' Sears Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC ® Marca Registrada / _ Marca de FAbrica / sM Marca de Servicio de Sears Brands, Mc Marque de commerce / _D Marque d_pos6e de Sears Brands, LLC ® Registered LLC ® Sears Brands, LLC
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 48 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Tue Feb 10 05:09:35 2009 Author : Title : Subject :EXIF Metadata provided by EXIF.tools