Craftsman 351214600 User Manual BAND SAW Manuals And Guides L0411302

CRAFTSMAN Saw Band Manual L0411302 CRAFTSMAN Saw Band Owner's Manual, CRAFTSMAN Saw Band installation guides

User Manual: Craftsman 351214600 351214600 CRAFTSMAN BAND SAW - Manuals and Guides View the owners manual for your CRAFTSMAN BAND SAW #351214600. Home:Tool Parts:Craftsman Parts:Craftsman BAND SAW Manual

Open the PDF directly: View PDF PDF.
Page Count: 2

UNPACKING
• Check for completeness. Locate all parts before attempting
assembly (see Figure 1).
NOTE: Hardware to mount toolsto stand is not included.
CAUTION: Do not attempt assembly if parts are
missing. Follow assembly instructions.Use parts list
to order replacement parts.
A Long Upper Cross Brace (2 each)
B Short Upper Cress Brace (2 each)
C Long Lower Cross Brace (2 each)
D Short Lower Cross Braco (2 each)
E Leg (4 each)
F Top (2 each)
Hardware Bag (not shown)
Figure 1 - Unpacldng
ASSEMBLY
Tools required: Phillipsscrewdriver, adjustable wrench and
portable drill.
ASSEMBLE FRAME
NOTE: Finger_ghten fastanemun_lall metalcomponentsare
assembled. Then tighten all fastoners securely.
NOTE: Use pan head screws and lock nuts.(Figure 7, Key
Nos. 8 and 9) to assemble all components except the top and
leveling pad.
• Assemblea longupper cress brace (A) and a longlower
cross brace (C) to the _legs (E}.The braces areassem-
bled to the INSIDE of the legs (see Figure 2),
•Repeat for the othertwo legs and longcress braces.
A
E
E
•Connecteach leg set by attachingthe two short uppercross
braces(B) and the twoshort lowercross braces(D) (see
Figure 3).
D
Figure 3 - Connect Leg Sets
•Tighten all fastanemcompletely.
ASSEMBLE LEVEUNG FOOTPAD
•Insertpad onto countominkscrew (see Figure4).
•Thread nut onto screw.Insert screw intoand throughfootpad.
•Place washer on screw.Thread second nutonto screw.
Nut Screw Pad
Nut /
Washer _ _Footpad
Figure 4 - Assemble Leveling Footpad
ATTACH FOOTPADS
•Slide one footpadonto the bottomof each leg. (One footpad
willincludeleveling device).Align cornerof footpadto cor-
ner of leg and pressfootpad onto leg.
ASSEMBLE TOP
•Locationof pre-drilledholes used in attachingthe top to the
frame are indicatedin Figure 5.
13"
1%" 1" 25/_6"1%"
Figure 5 -Top Hole Pattern
Figure 2 - Assemble Leg Set
• Placetheboardstogetherandthenplacethe assembled
frame onthe boards,Attachflame to boards usingwood
screws and washers throughthe slots in the frame (see
Rgum 6),
NOTE: The center screw requires one washer under the
screw head and one additional washer between the frame
and board.
Center Screw Requires
Extra Washer Between
Tabletop and Frame
\
Figure 6 - Attaching the Top
IMPORTANT: Forscroll saw 22436, the two rear and one of
the front mounting belts will need to be located through the
slots in the frame. Carefully ddll the two holes shown in
Figure 7 and then place saw on stand, mark Ioca_on of the
other two holes, then drill holes.
_ 2_/=" "/,e"
Figure 7 - Drill Mounting Holes for Scroll Saw
3
4
._p_-12
Figure 8 - Parts Illustration for Stand
KEY
NO. PART NO.
1 117020231
2 117020232
3 117020234
4 117020235
5 117020233
6 116 620 267
7 117900073
8 116710117
DESCRIPTION
Long Upper Crces Brace
Short Upper Cross Brace
Long Lower Cross Brace
Short Lower Cross Brace
Leg
Footpad
Tabletop
Pan Head Screw (M6xl0)
ANot Shown
QTY.
2
2
2
2
4
4
2
24
KEY
NO.
9
10
11
12
13
14
15
A
PART NO.
116 710 020
116 710 003
116700021
116 620 268
116 700 027
116 700 089
116 720 077
119 900 873
DESCRIPTION QTY.
Nut, Self-loddng (M6) 24
Countersink Screw (M8x40) 1
Nut (M8) 2
Pad 1
I
(8.4) I 1
Washer
Pan Head Wood Screw (M6x16) ! 10
Washer (6.4) 12
Hardware Bag 1

Navigation menu