Craftsman 35122632 User Manual BELT/DISC/SANDER/MITER GAUGE Manuals And Guides L0807542
CRAFTSMAN Sander Manual L0807542 CRAFTSMAN Sander Owner's Manual, CRAFTSMAN Sander installation guides
User Manual: Craftsman 35122632 35122632 CRAFTSMAN BELT/DISC/SANDER/MITER GAUGE - Manuals and Guides View the owners manual for your CRAFTSMAN BELT/DISC/SANDER/MITER GAUGE #35122632. Home:Tool Parts:Craftsman Parts:Craftsman BELT/DISC/SANDER/MITER GAUGE Manual
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
MANUAL, MODEL N@o 351 °22532 and MITER CAUTION: READ o assembly' ALL o operating gNSTRUCTgONS CAREFULLy! i . , repair parts i,, Sold by SEARS, ROEBUCK AND CO., Chicago, 0L60684 U.S.A. Part No, 138000 Copyrighted FULL ONE YEAR _=< WARRANTY ON SEARS CRAFTSMAN If within one year from the date of purchase, this Sears Craftsman Belt & Disc Sander fails due to a defect in material or workmanship, Sears will repair it, free of charge WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. ==_ c_< This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., DEPT.698/731A SEARS TOWER, CHICAGO, GENERAL SAFETY INSTRUCTIONS IL 60684 FOR POWER TOOLS BEFORE ANY WORK IS DONE, READ THE CAUTIONS LISTED BELOW CAREFULLY. WORKING SAFELY PREVENTS ACCIDENTS° b. Consult the owner's manual for specific maintaining and adjusting procedures, c, Keep machine lubricated 1 OPERATOR SHOULD BE PREPARED JOB: d. Use sharp blades, and keep the tool clean for best, and safest operation, e. Never leave adjusting keys and wrenches on machine; remove them FOR THE a Do not wear loose clothing, jewelry or gloves that will get caught in moving parts of the machine_ b, Wear safety shoes with non-slip soles. L Workbed of power tool should only be used to support the workpiece and necessary accessories_ c Wear safety glasses. d. Wear face mask or dust mask when needed. g Use recommended accessories only, and follow manufacturer's instructions. e. Be alert, and think clearly. f. Never operate power tools when tired, intoxicated, or when taking medications that cause drowsiness. 2. WORK AREA SHOULD BE READY FOR THE JOB: a, An uncluttered work area ensures that the operator has ample room for movement and placement of the work_ Clean floors ensure good footing b, Environment should be suitable for tool; Power tools should not be used in damp locations, or gaseous, explosive atmospheres. c. Area should be properly lighted_ d Proper electrical outlet should be available for the tool. 1. Three-prong plug should be plugged directly into a properly grounded three-prong receptacle 2. If work area is not grounded, a qualified electrician should install the proper electrical system. e_ Extension cords should have a grounding prong, and the three wires of the extension cord should be the correct gauge. f Keep visitors a safe distance away from work area_ 3 TOOL SHOULD BE MAINTAINED: a. Always unplug power tool prior to inspection or maintenance. h, Keep all guards in place. i Keep all parts in working order; do not perform makeshift repairs (Use the Parts List provided with the owner's manual to order replacement parts.) j. Make sure the machine is mounted correctly; never attempt to stabilize a floor or benchtop tool by standing on it, or by holding it in position 4, OPERATOR SHOULD KNOW HOW TO USE THE TOOL: a_ b. Use the right tool for the job. Avoid accidental start-up; make sure that the machine is in the OFF position before plugging it in. c Do not force a tool; it will work most efficiently at the rate for which it was designed d. Turn the machine OFF if it jams: A blade jams when it digs too deeply into the work. (The motor force keeps it stuck in the work.) e. Handle the work piece correctly. 1. Secure the work with clamps, or a vise whenever possible; leave hands free to operate the machine 2 Use push sticks or push blockswhen required; protect hands from possible injury. f Do not overreach: Keep the proper footing and balance_ g. Keep hands away from moving parts and cutting surfaces h Know your power tool: learn its operation, applications and specific limitations. CONTENTS Warranty ......................................................... 2 General Safety Instructions for Power Tools ........................................ 2 Safety Instructions for Belt & Disc Sander ............................... Motor Specifications and Electrical Requirements Electrical Connections 3 Unpacking and Checking ..................................... 5 6 Assembly 6 ........................................................ Operation ........................................................ Maintenance ....................... Contents ................... Tools Needed .................................................. 8 10 ................................................. 4 Trouble Shooting ........................................... 11 5 Replacement Parts List .................................. 12 Replacement Parts Illustration ........................ 14 SAFETY BNSTRUCTnONS FOR l in. BELT & 8in. DiSC SANDER WARN|NG-" DO NOT ATTEMPT TO OPERATE BELT & DISC SANDER UNTIL IT IS COMPLETELY ASSEMBLED ACCORDING TO THE INSTRUCTIONS. 1 KNOW GENERAL POWER TOOL SAFETY. Make sure all precautions are understood and provided for (page 2) 2 SECURE ALL FASTENERS, Frequently check that nuts and bolts are tight and have not vibrated loose 3 FOLLOW OPERATION INSTRUCTIONS. Operate the belt and disc sander as described in this manual (page 8) 4 BE SURE MOTOR RUNS CLOCKWISE. Abrasive belt must travel down 5 DISC SAND ON DOWN SIDE (RIGHT SIDE). The disc should pull work towards the table_ 6 SUPPORT WORKPIECE. workpiece at all times Maintain control 11. KEEP SANDER MAINTAINED. maintenance instuctions (page 10) Follow 12. DISCONNECT POWER, Turn switch "off" and diconnect the power whenever sander is not being used CAUTION: DO NOT ALLOW FAMILIARITY (GAINED) FROM FREQUENT USE OF YOUR BELT AND DISC SANDER TO BECOME COMMONPLACE ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY The operation of any power tool can result in foreign objects being thrown into the eyes. which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87.1 (shown on package) before commencing power tool operation Safety Goggles are available at Sears retail or catalog stores of 7. DO NOT FORCE WORK, Slowing or stalling the motor will overheat it 8, DO NOT OVERHEAT WORK_ Move metal across the abrasive and cool it when it becomes hot 9 10 DO NOT WET GRIND OR POLISH. Never use a steady stream of water on the workpiece Only quench the workpiece in water to cool it, DO NOT GRIND OR POLISH MAGNESIUM. could catch on fire It THINK SAFETY: Safety is a combination of operator common sense and alertness at all times when the Belt & Disc Sander is being used. MOTOR SPECIFICATOONS AND ELECTRICAL MOTOR PROPERLY GROUNDED The Belt and Disc Sander is assembled with motor and wiring installe& GROUNDING The 120 Volt AC capacitor start motor has the following specifications: 3-PRONG PLUG Horsepower REQUIREMENTS ................................................................. 1/3 Voltage ................................................................. 120 Amperes .............,......................................................... 7 Hertz ......................................................................... 60 Phase ................................................................ Single RPM .......................................................................... 1725 OUTLET PRONG This unit is for use on less than 150V, it has a plug as illustrated above. If the outlet you are planning to use for this power tool is of the two prong type, use an adapter as shown below, Rotation (viewed from pulley end) ............. clockwise Frame size .................................................. NEMA 56Z The green grounding lug extending from the adapter must be connected to a permanent ground, such as to a properly grounded outlet box. Use Sears Craftsman _912037C motor if a replace. ment motor is needed Having a qualified electrician replace the two prong outlet with a properly grounded three prong outlet is recommended POWER SOURCE GROUNDING LUG A...... _ ;f=:_MAKE SURE THIS u_r'rcn_ "_'_l IS CONNECTED 3-PRONGPLUG \ _ If_IITOAKNOWN CAUTION: DO NOT CONNECT THE BELT AND D)SC SANDER TO ITS POWER SOURCE UNTIL ALL ASSEMBLY STEPS HAVE BEEN COMPLETED The motor is designed for operation on the voltage and frequency specified on motor nameplate, Normal loads will be handled safely on voltages not more than 10% above or below the nameplate voltage. /."_"_'- "_"_ 2-PRONG _" RECEPTACLE NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prong receptacle Adapter is not allowed in Canada by the Canadian Electrical Code. Running the unit on voltages which are not within the range may cause over-heating and motor burn-out EXTENSION CORDS Heavy loads require that voltage at motor terminals be not less than the voltage specified on narneplate, The use of any extension cord will cause some drop in the voltage and loss of power This machine must be grounded while in use to protect the operator from electric shock The wires of the extension cord must be sufficient in size to carry the current and maintain adequate voltage. This power tool is equipped with a 3-conductor cord and grounding type plug which has a grounding prong, approved by Underwriters Laboratories and the Canadian Standards Association, Use the table below to determine the minimum wire size (A WG,) extension cord. Use only 3 wire extension cords which have 3 prong grounding type plugs and 3-pole' receptacles which accept the tool plug Do not remove or alter the grounding prong in any manner. If power cord is worn; cut, or damaged in any way, have it replaced immediately_ This plug requires a mating 3-conductor grounded type outlet as shown. Extension cord Length Wire Size A.W.G. Up to 50 ft ................................................................. 50 - 100 ft ................................................................ 16 14 Use a 110-120V properly grounded type outlet protected by a 15-amp. time delay fuse or circuit breaker NOTE: Using extension cords over 100 fL long is not recommended. WARNaNG: BE SURE THAT THE OUTLET IS PROPERLY GROUNDED, HAVEIT CHECKED BY A QUALIFIED ELECTRICIAN° WARNBNG: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUGS WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM ELECTRICAL CONNECTIONS WARNING: MAKE SURE THE UNIT IS "OFF" AND DISCONNECTED FROM THE POWER SOURCE BEFORE INSPECTING ANY WIRING. GREEN _.-.----- POWER The motor and wiring are installed as shown in the wiring diagram(See Figure 1) A label on the motor describes configurations WHITE the possible wiring The motor is assembled with an approved three conductor cord to be used on 115 volts as indicated ILACK If T5 and T6 are interchanged, the direction of rotation will be reversed 1 GREEN (GROUND) GREEN The power supply to the motor is controlled by a double pole safety rocker Remove the key to prevent unauthorized use_ The power lines are inserted directly into the switch. Both green ground lines must remain securely fastened to the frame to properly protect against electric shock UNPACKING o,sc ALUMINUM SANDING Figure 1 AND CHECKING CONTENTS DISC GUARD BELT GUARDS DISC TABLE PULLEY V-BE LT TABLE SUPPORT ABRASIVE t£._ SANDING DISC _ ..... IVH/CH GAUGE E Figure 2 Check for shipping damages If damage has occurred, a claim should be filed with the carrier for fastest action. The belt and disc sander is assembled to the base at the factory. H G BELT TABLE L M N J. Hex bolt, 1/4"-20 X 3/4; 4 each for attaching feet to base. K Flat washer, 1/4"; 6 each. L. Rubber Foot, 4 each. Additional parts which need to be fastened to the unit should be located and accounted for (see Figure 2) M Locate the parts bag and make sure the proper hardware is included. O. Tension Handle; 1 each_ A Hex bolt, 5/16"-18 X 1 1/4"; 4 each for attaching the table mounting bracket to the base B. Socket head bolt, 5/16"-18 X 1 1/4"; 2 each for mounting disc table to bracket. C Flat washer, 5/16"; D Lockwasher, E Nut, 5/16"-18, F 12 each+ Lockwasher, 1/4"; 4 each. N. Nut, 1/4"; 4 each. P. Knob; 1 each. Q. Screw, 3/16"-24-3/8"; 2 each R. Flat washer, 3/16"; 2 each Adjusting tools are also located in the parts bag See tools needed (Page 6) Unpainted steel surfaces have been coated with a shipping preservative. 5/16"; 6 each. 6 each Socket head bolt 3/8"-16 X 3/4"; fastening belt table to the frame i/'"_:"_'_'-_- I!_ 114_...___4_"_) u'_"" _l 1 each for Remove the preservative with kerosene or penetrating oil. G Flat washer, 3/8"; 1 each. Use soap and water on rubber and plastic parts Cleaning fluids tend to deteriorate them H Non41amable solvents are recommended Lockwasher, 3/8" 1 each. I Thumb knob; 2 each for fastening belt cover to frame CAUTION: DO NOT ATTEMPT ASSEMBLY iF PARTS ARE MISSING USE OWNERS MANUAL TO ORDER TOOLS J 10-12-14mm WRENCHES / NEEDED J 10-12-" SOCKETS & RATCHET HANDLE #2 PHILLIPS SCREWDRIVER ASSEMBLY 3.5-6-8mm HEX WRENCHES (SUPPLIED) COMBINATION SQUARE (Refer to figure 6) The frame (Key No_ 77) and the motor are fastened to the base (Key No 1) INSTALL THE "V" The loose items which need to be attached have been described in unpacking and checking contents No 46) 2 Remove the screw (Key No 48) and rear belt guard (Key No 45) to remove the belt Fasten the additional parts in the manner described below, the order is important, t BELT (Key NOo 50) The "V" Belt is located inside the belt guard 3 Place the "V" (Key belt around the pulleys 4. Belt guard will be installed bracket is installed after the disc table MOUNT THE BELT AND DISC SANDER TENSION THE "V" BELT 1 The base has a mounting flange on each side 2 Each flange has three mounting holes 1 The "V" belt is tensioned by moving the frame (Key No 77) forward 3 The holes toward the front and the holes which are 101/2" from them can be used to mount the belt and disc sander to a leg set 2 Loosen the mounting nuts (Key No 7) so the frame can be moved Remove wheel cover (Key No 76) if necessary 4 The Sears leg set can be set up to accomodate a set of holes with 9" X 101/2'' spacing. 3 Move the frame by rotating the tension bolt (Key No 10) clock wise; to tighten the belt 5 Mount the base to the leg set prior to assembly (mounting bolts not included), 4 The belt is properly tightened when light pressure applied between the pulleys produces about 3/8" deflection_ MOUNT THE FEET 1 Four rubber feet (Key No_2) and mounting hardware are supplied. 5 Do not over tighten; a belt which is too tight will wear fast and over work the motor 6 2 Use the feet if the sander is not fastened directly to a leg set Make sure the pulleys are aligned; poorly aligned pulleys make the unit vibrate and reduce the belt life 3 Use the mounting holes which are farthest appart 7 Once the belt is tensioned and aligned secure the position by tightening the mounting nuts 4 Push the bolts through the washer (Key Nos. 5&30), then through the base and the rubber foot POSITION DISC TABLE 5 Fasten the feet with the lock washers and nuts (Key Nos 3 & 4) 6 The additional hole in each flange carl be used to fasten the sander to a bench top after it is assembled INSTALL THE MOTOR PULLEY (Key No. 26) 1. The set screw (Key No. 27) is installed in the pulley 2 Slide the motor pulley on to the motor shaft with set screw over the flat of the shaft. BRACKET The disc table bracket is attached with a combination of bolt, two flat washers, Iockwasher and nut (4 each, Key Nos 18, 9, 6, & 7). 2 Attach the bracket using the two holes closest to the left edge of the base, the two mounting bolts closest to the motor will be installed after the disc table is adjusted 3 Insert the bolts through one flat washer, the bracket and the base 4 Attach the washer, beneath lockwasher, and nut from 3 Align the pulleys, use a straight edge if necessary 4 Secure the pulley position with the set screw 5 Only thread the nut on with a few turns the bracket must be loose in order to position the belt guard FASTEN THE BELT GUARD 1 The rear belt guard (Key No 45) and screw (Key No 48) should be unattached_ 6 Use a square to set the table at 90 ° to the disc and tighten the bolts 2 Hold the belt guard with the drive pulley end up and position it with the motor shaft through the opening in the guard 7 Reposition the mounting bracket so that the table and disc are parallel and the gap between them is 1/16" 3 Rotate the guard into place, bring it clown over the belt guard supports (Key No 47) 8. Reposition the disc on the motor shaft if the table cannot be moved in far enough to close the gap 4 Move disc table bracket so the guard can be positioned on the supports, but leave the mounting bolts (Key No 18) positioned 9 5 Attach the belt guard with the washers and thumb knobs (Key Nos 30 & 49) 1. Once the table is positioned, 6 SECURE THE DISC TABLE. Replace the rear belt guard and screw. 3 Use a socket and ratchet handle from under the sander to secure the bracket to the base 1 The set screw (Key No 22) is installed in the disc. 3 4. Install the two remaining bolts through the holes closest to the motor in the same manner. Slide the disc on to the motor shaft with set screw over the flat FASTEN THE DISC GUARD Position disc back onto motor shaft but, make sure that the motor shaft will not interfere with the abrasive disc 1. The disc guard (Key No. 23) attaches to the disc table bracket with two screws and Iockwashers (Key Nos 24 & 25) 4 Tighten set screw to lock position FASTEN ABRASIVE 2 DISC 1. The abrasive disc (Key No backing Position the disc guard so it is centered and the lip covers the outer edge of the disc INSTALL THE BELT TABLE 19) has an adhesive 1 The belt table bracket (Key No. 54) is attached to the belt table 2 Theadhesive is not reusable. Be certain to place it centered on the disc 2_ 3. Peel off the adhesive's covering and press the adhesive disc firmly against the aluminium disc 3_ ALIGN THE DISC TABLE 1 Finger4ighten the disc table bracket mounting bolt& Allow for adjustment The table and bracket are fastened to the frame with the socket head bolt, Iockwasher and flat washer (Key Nos. 52, 53, & 11)_ The belt table is angled and positioned 1/16"away from the belt at the same time. 4. if the table slot is not centered over the belt and platen, the belt table bracket needs to be repesitioned. 2 The table is attached to the bracket with a socket head bolt, two flat washers, a Iockwasher and a nut (two each, Key Nos 17,9,6 &7). 3 secure the bracket 2 Use an open-ended wrench to hold the head of the hex bolt (Key No 18). INSTALL THE DISC 2 Make sure the disc is centered relative to the table INSTALL THE TENSION HANDLE 1 Thread the knob (Key No. 63) onto the end of the handle farthest from the fiats_ Hold the table in position and insert bolts through washers, the table and the bracket 2 Screw handle into the spring cap (Key No 66) 4 Fasten the table by threading the washers and nuts onto the bolts; finger tighten. 3 Use flats of handle to secure the handle to the spring cap 5 When the table mounting bolts are finger tightened, the table can be positioned at any angle from 45 ° to 90 ° to the disc 7 OPERATDNG INSTRUCTIONS SAFETY PRECAUTIONS REPLACING ABRASIVE WARNING: ALWAYS OBSERVE THE FOLLOWING SAFETY PRECAUTIONS. Remove the wheel guard (Ref No 76) by removing thumb knobs (Key No 49) Whenever adjusting or replacing any parts on the sander turn switch "OFF" and remove plug from power source Remove belt table (Key No 59) by removing socket head bolt (Key No 52) Recheck table locking nuts and bolts. They must be tightened securely Make sure all guards are properly attached All guards should be fastened securely Make sure all moving parts are free and clear of any interference; With power disconnected, test operation by hand for clearance and adjust if necessary. Make sure abrasive belt always tracks properly; Correct tracking gives optimum performance After turning switch "On" always allow the belt to come up to full speed before sanding or grinding Keep your hands clear of abrasive belt, disc and all moving parts For optimum performance do not stall motor or reduce belt speed; Do not force the work into the abrasive BELT Release the tension on the belt by pulling the tension handle (Key No 65) forward (towards operator) Remove belt from the top wheel (tracking wheel, Key No. 72) release the tension handle and remove belt Install abrasive belt in the reverse manner Place the abrasive belt squarely on the wheels spring action will tension the belt. Make sure the belt is tracking correctly tracking if necessary The arrow should point down toward the belt table to ensure that the splice in the belt will not come apart When the belt is tracking properly it rides squarely on the center of each wheel Replace the wheel guard and belt table Replace abrasives when they become loaded (glazed) or frayed Remove the wheel guard Never attempt wet cutting If the workpiece becomes too trot to handle, cool it in cold water. Always wear eye protection or face shield WEAR YOUR Adjust the The abrasive belt has an arrow printed on the inside which indicates the direction of travel Never push a sharp corner of the workpiece rapidly against the belt or disc; The abrasive may tear When grinding metal: Move the workpiece across the abrasive, to prevent built up heat The TRACKING ABRASIVE BELT Test the tracking Plug in power cord Turn the switch "ON" and immediately "OFF' If the abrasive belt did not move to the right or left, it is tracking properly If the belt moved to the right or left, adjust the tracking To adjust the tracking wheel loosen the lock-nut (Key No 4), Use a 3mm setscrew wrench (Key No 21) to turn the tracking adjusting screw (Key No 63) If the abrasive belt moves to the right, tilt the top of the tracking wheel towards the frame by turning the adjusting screw clockwise TENSIONING ABRASIVE BELT Tension is created by a spring loaded cam shaft The tracking wheel is mounted on the opposite side of the shaft The spring return is transmitted to the tracking wheel and maintains the tension If the abrasive belt moves to the left, tilt the top of the tracking wheel away form the frame by turning the adjusting screw counter-clockwise Lock the position when the belt is tracking properly; so the belt will remain centered on the wheels. Hold the position of the tracking adjustment screw with the 3mm setscrew wrench Tighten Iocknut (Key No 64) to lock the position Replace wheel guard and secure with thumb knobs ADJUSTING BELT TABLE ANGLE To adjust the angle of the belt table, loosen the socket head bolt (Key No 52) and adjust to the desired angle Use a combination square to set the belt table at 45 ° or 90 ° to the abrasive belt Adjust for 1/16" clearance between the belt and the table When the belt table is at the desired angle, lock it into position by securely tightening the socket head bolt ABRASIVE Figure 5 BELT FINISHING REPLACING THE ABRASIVE DISC. The abrasiye belt can be used to sand wood, deburr metal, or polish plastic and glass The belt is most efficient when used with the table The 1" belt size is convenient for getting into corners and concave curved edges ADJUSTING BELT PLATEN Operating with the belt platen in place will allow the operator to sand or grind straight even lines Belt edges should be even with platen edges, (Key No 58) To adjust belt platen, loosen two each 1/4-20 X 5/8" hex head bolts (Key No,67) and adjust Tighten bolts securely POLISHING Remove disc table (Key Na15) Remove old abrasive disc by peeling it from the aluminum disc Removing aluminum disc from motor shaft is not necessary. Clean aluminum disc if necessary Select the proper abrasive disc and apply to ah_minum disc. The abrasive used can be changed to a different grit without replacing the abrasive disc. Additional aluminum discs are available (see recommended acessories) use separate aluminum disc for each grit size use& Interchange the aluminum disc to change grit size (see assembly page 7) AND CONTOUR SANDING: Remove platen completely, remove hex head bolts and washers (Key Nos 57, 3 & 30) Replace disc table ADJUSTING The belt has'ho rigid back and is able to follow the contour of curved parts Move the workpiece against the belt The belt will follow the contour (See Figure 4) DISC TABLE ANGLE The disc table is adjustable from 45 ° to 90 ° for beveled work To adjust the disc table, loosen the two socket head bolts and nuts (Key Nos. 17 & 7) and adjust to the desired angle Use a combination square to set the disc table at 45 ° or 90 ° to the abrasive disc When disc table is at desired angle, lock it into position by securely tightening the socket head bolts. ABRASIVE Abrasive disc sanding is well suited for finishing small end surfaces and convex curved edges Figure 4 SHARPENING: Move the workpiece across the "down side" (Right) of the face of the abrasive disc Adjust belt table to the desired sharpening angle and tighten securely Use the belt sander to notch the back of an auxiliary piece of wood Using a "C" clamp, attach the auxiliary piece of wood to the table, it acts as a support while sharpening (See Figure 5) Top edge of the wood should be approximately frnm _bra_iv_ h_,lt DISC FINISHING 1/16" The abrasive disc produces almost no abrasive action at the center. The abrasive disc moves fastest and removes more material at the outer edge If workpiece is fed without additional guidance, more material will be removed towards the outer edge of the disc. Fnr _r',"ura,"v i,_e the miter nm_ne USING THE MITER GUAGE The miter gauge is used only on the disc table. Use the miter gauge for securing work and holding the pro* per angle, while disc sanding Adjust the angle by repositioning the miter gauge scale (Key No 29) and locking it into place with thumbscrew and flatwasher (Key Nos 31 & 30). Check the accuracy of the miterguage scale, Use a combination square to adjust the miter gauge square to the face of the disc. Indicator (Key No 32) should be at zero, Loosen screw (Key No24) and reposition indicator if necessary DUST COLLECTION: The wheel cover has a I 1/4" diametel: exaust port in it The exhaust port will accept a standard 1 1/4" Dust collection hose. Use the exhaust port to connect the belt and disc sander to a shop vac or dust collector, RECOMMENDED ACCESSORIES ABRASIVE BELTS 1" x 42" FINE ..................................... MEDIUM ............................. COARSE ................................. ABRASIVE DISCS 8" , ................... ALUMINUM DISC 8 ........................ STEEL STAND ..................... POWER TOOL KNOW HOW "HANDBOOKS" TABLE SAW ............................... RADIAL SAW .......................... _ 26056 9 26055 9 26054 922745 925135 922244 _ 2918 9 2917 The above recommended accessories are current and were available at the time this manual was printed MAINTENANCE WARNING: MAKE CERTAIN THAT THE UNITIS DISCONNECTED FROM THE POWER SOURCE BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENT. LUBRICATION The shielded ball bearings in this sander are permanently lubricated at the factory, they require no further lubrication. CLEANING Keep machine and workshop clean. Do not allow sawdust to accumulate on the belt and disc sander_ Keep the wheels clean, Dirt on wheels will cause poor tracking and belt slippage. Operate sander/grinder with dust collector to keep dust from accumulating IMPORTANT: AFTER SANDING WOOD OR NONMETALLIC MATERIAL, ALWAYS CLEAN DUST COLLECTOR AND WHEEL GUARD OF SAWDUST BEFORE GRINDING METAL THE SPARKS COULD IGNITE THE DEBRIS AND CAUSE A FIRE Be certain motor is kept clean and is frequently vacuumed or blown free of any dirL Unpainted surfaces should be cleaned with penetrating oil. Use soap and water to clean painted parts, rubber parts and plastic guards. A small amount of machine oil can be applied to the cam shaft (Key No 62) within the tracking bracket° When operation seems stiff, a coat of automobile-type wax applied to the belt table and disc table will make it easier to feed the work while finishing. Do not apply wax to the belt platen, the belt could pick up the wax and deposit it on the wheels, causing the belt to slip. KEEP SANDER IN REPAIR *." If power cord is worn, cut, or damaged in any way, have it replaced immediately, Replace V-belt and worn abrasives when needed. Replace any damaged or missing parts, use the parts list to order parts, TROUBLE SHOOTING WARNING: FOR SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. Trouble Probable Cause Any attempt to repair the motor may create a hazard unless repair isdone by qualified service technician Repair service is available at your nearest Sears Store, Remedy ,,,,,,,, Motor will not start 1 Low voltage 1 Check power line for proper voltage, 2 Open circuit in motor or loose connectionSr 2 Inspect all lead terminations on motor for loose or open connection 1 Short circuit in line, cord or plug 1 Inspect line cord or plug for damaged insulation and shorted wires. 2 Short circuit in motor or loose connections 2. Inspect all lead terminations on motor for loose or shorted termials or worn insulation on wires m Motor will not start, fuses or circuit breakers "blow" 3 Incorrect fuses or circuit breakers in powerline Motor fails to develop full power (power output of motor decreases rapidly with decrease in voltage at motor terminals) Motor overheats Motors stalls (resulting in blown fuses or tripped circuit breakers) Frequent opening of fuses or circuit breakers 3. Install correct fuses or circuit 1 Power line overloaded 1. Reduce the load on the power line. with lights, appliances and other motors 2 Undersize wires or circuits too long 2 Increase wire sizes, or reduce length of wiring 3 General overloading of power company's facilities 3 Request a voltage check from the power company 1. Motor overloaded 1 Reduce load on motor 2 Air circulation through the motor restricted. 2 Clean out motor to provide normal air circulation through motor 1 Short' circuit in motor or loose connections 1 Inspect terminals in motor for loose or shorted terminals or worn insulation on lead wires 2 Low voltage 2 Correct the tow line voltage conditions 3 Incorrect fuses or circuit breakers in power line 3 Install correct fuses or circuit 4 Motor overloaded 4 Reduce load on motor 1 Motor overloaded I1 Reduce motor load Abrasive belt runs off top wheel breakers 2 Incorrect fuses or circuit breakers 2, Install correct fuses or circuit breakers 1. "V"-Belt 1. Adjust belt tension by pushing motor toward back until all slack is removed from belt ,, Machine slows down while operating breakers to loose i 2 Applying too much pressure to workpiece 2 Ease up on pressure 1. Not tracking 1 See operations section "Tracking Belt" properly. REPLACEMENT KEY NO_ PART NO. PARTS LIST QTY. DESCRIPTION 1 2 3 4 5 1381,00 133600 STD55t125 STD541025 STD522507 Base Rubber Foot * Lockwasher, 1/4" * Nut, 1/4"-20 * Hex bolt, 1/4"-20 x 3/4" 1 4 13 5 4 6 7 8 9 10 STD551131 STD541031 1405,00 STD551031 STD523730 * Lockwasher, 5/16 x 9/16" * Hex nut, 5116"-18 Tension plate * Flatwasher, 5/16 x 3/4" Tension bolt, 3/8-16 x 3" 16 14 1 22 1 11 12 13 14 15 STD551037 STD541431 STD533107 _12037C 1406.00 * Flatwasher, 3/8" x 1" * Locking nut, 3/8"-16 Carriage bolt, 5/16-18 x 3/4" Motor Disc table 3 1 4 1 1 16 17 18 19 20 140700 1382 00 STD523112 _22745 _25135 Disc table bracket Socket head bolt, 5/16"-18 x 1 1/4" Hex head bolt, 5/16"-18 x 1 1/4" a Abrasive disc (adhesive backing) medium a Aluminum disc (8") 1 2 4 1 1 21 22 23 24 25 1658.00 STD502502 1383.00 STD511002 STD551110 * Hex wrench, 3rnm * Setscrew, 1/4"-20 x 1/4" Disc guard * Phillips head screw. 3/16"-24 Lockwasher, 3/16" x 5/16" 1 2 1 5 5 26 27 28 29 30 141100 STD502503 0905.00 0904.00 STD551025 Motor pulley * Setscrew, 1/4"-20 x 3/8" Miter gauge slide bar Miter gauge scale * Flatwasher, 1/4 x 314" 31 32 33 34 35 090200 090100 144600 141200 1413.00 Thumbscrew knob Indicator Miter gauge assembly (Includes Key Nos_ 28-32) Line cord, (power to switch) SJT, 3C/14AWG Strain relief 1 1 1 1 4 36 37 38 39 4O 1414.00 141500 141600 1384.00 1385.00 1 2 1 1 1 41 42 43 44 45 147400 1475 O0 147&00 147700 1386.00 Line cord, (switch to motor) SJT. 3C/14AWG Rubber grommet Switch box Safety switch (2-pole locking rocker) Locking rocker key Ground star washer' Ground cup washer Ground flatwasher Phillips head, ground screw, 3/16"-24 x 3/8" Rear belt guard __-- [] See recommended accessories (page 10) * Standard hardware item available locally x 1/4" 1 3 1 1 13 2 2 2 2 1 REPLACEMENT PARTS LIST (Continued) KEY NO, PART NO. 46 47 48 49 5O 1387 00 141900 138800 143700 STD304380 Belt guard Belt guard support * Thread forming scew Thumb knob * V-belt (A38) 1 2 1 4 51 52 53 54 55 1420 00 1389 00 STD551137 1421,00 1390.00 Drive pulley * Socket head bolt. 3/8"-16 x 3/4" * Lockwasher, 3/8" x 11/16" Belt table bracket * Socket head bolt, 5/16-18 x 3/4" 1 1 1 1 2 56 57 58 59 60 1846 00 1391.00 142300 1392.,00 1393.00 * Hex wrench. 8mm * Socket head bolt 1/4"-20 x 5/8" Belt platen 1" Belt table * Socket head bolt, 1/4"-20 x 1/2" 1 5 1 1 4 61 62 63 64 65 1424.00 1431 00 1394.00 1395.00 1425.00 Spring plate Tracking wheel cam shaft Knob * Setscrew, 1/4"-20 x 3/4" Tension handle 2 1 1 1 1 66 67 68 69 7O 1426 00 1427.00 1428.00 1429,00 1447.00 71 72 73 74 75 1448.00 1396 00 139700 STD315205 1434.00 76 77 78 79 8O 1398.00 143500 143600 143800 1439.00 81 82 83 84 85 1440 00 144100 STD315225 144200 1449.00 Bearing housing * Retaining ring (internal 23mm) * Bearing (6202) Drive shaft Bearing housing assembly (includes Key Nos. 81-83) 1 2 2 1 1 86 87 88 926055 112600 1127,00 1380 00 Abraskie belt (cloth), medium Hex wrench, 4mm Hex wrench, 5mm Owners Manual 1 1 1 1 DESCRIPTION Spring cap Tension spring Retaining ring Tracking bracket Tracking/Tension Assembly (includes Key Nos. 62-70) Wheel Assembly (includes Key Nos 73&74) Idler Wheel * Retaining ring * Bearing, (6200) * Retaining ring (E type) Wheel guard Frame Wheel guard support Idler wheel shaft Drive wheel Always order by Part No ; NOT by Key No QTYo 1 1 1 2 1 1 1 2 2 2 2 1 1 2 1 1 7O / 4 3 69 64 62 21 35 38 45 39 4O 19 2O 49 5O 3O Figure 6 71 76 77 74 73 3O 49 3o ! 79 72 3O 57 47 86 80 _ 87 35 9 56 \ ,. 35 59 \ 54 9 52 34 9 I0 8 . 88 1 MODEL NO. 351.22632 Now that you have purchased your Belt and Disc Sander should a need exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores Be sure to provide all pertinent facts when you call or visit, The model number of your 1-inch belt and 8-inch will be found on the side of the base disc sander All parts listed may be ordered from any Sears Service Center and most Sears stores_ If the parts you need are not stocked TO ORDER REPAIR PARTS locally, your order will be electronically Repair Parts Distribution transmitted to a Sears Center for handling, WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: PART NUMBER PART DESCRIPTION MODEL NUMBER 351.22632 NAME OF ITEM 1-in Belt and 8-in Disc Sander Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U,_S;A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Mon Aug 04 04:15:30 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools