Craftsman 351275931 User Manual COMPOUND MILLING TABLE Manuals And Guides L0521267
CRAFTSMAN Workbench / Project Manual L0521267 CRAFTSMAN Workbench / Project Owner's Manual, CRAFTSMAN Workbench / Project installation guides
User Manual: Craftsman 351275931 351275931 CRAFTSMAN COMPOUND MILLING TABLE - Manuals and Guides View the owners manual for your CRAFTSMAN COMPOUND MILLING TABLE #351275931. Home:Tool Parts:Craftsman Parts:Craftsman COMPOUND MILLING TABLE Manual
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Operator's Manual CRR.FTSMRN ° COMPOUND Model No. 351.275931 CAUTION: MILLING TABLE Read and follow all Safety Rules and Operating Instructions before First Use of this Product. • • • • • Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 16305.01 Draft (05/20/00) Safety Assembly Operation Maintenance Parts List Warranty ....................................... 2 Safety Rules .................................... 2 Unpacking ..................................... Assembly ....................................... 2 2 Operation .................................... Maintenance .................................... 2-3 3 Parts Illustration and List ......................... 4-5 WARNING:Never use highly volatile solvents. Avoid getting cleaning solution on paint as it may tend to deteriorate these finishes. Use soap and water on painted components. Refer to Figure 1, • Attach each handle (Key No. g) to handwheai (Key No. 13) with handle screw (Key No. 10). • Tighten each screw securely. • Attach one hendwhee[ (Key No. 13) to cross feed screw (Kay No. 21) with key (Key No. 5) and locking nut (Key No. 12). FULL ONE YEAR WARRANTY • Attach two handwhesls to longitudinal feed screw (Key No. 7) with keys and locking nuts. if this product fails due to a defect in material or workmanship within one year from the date of pumhase, Sears will at its option repair or repiaae it free of charge. • Tighten each locking nut securely. Contact your nearest Sears Service Center to arrange for product repair, or return this product to place of purchase for replacemnt. ti this product is used for commercial or rental purposes, this warranty will apply for 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also 'have other rightswhich vary from state to state. DESCRIPTION Craftaman Compound Milling Table is manufactured from cast iron and steel The table fits most drill presses. Milling operations can be done by moving work right and left (longitudinal), or front and back (cross) directions. The table can also be used to accurately position or index a workpiece under a drill but when not doing milling operations. A U-clamp hold down set is included with the table. Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 6O179 • The Milling Table is heavy. Do not lift it by the crank handles. • Make sure that drill press table is fastened securely, does not shift in any direction, and is clean and free of nicks and burrs. • Understand and follow all safety instructions supplied with drill pre._s,or other machines on which milling table is used, • Mount table to work surface by polting or clamping base securely in four mounting locations. • Be alert and think clearly. Always check your set up; for example, rotate accessory by hand before applying power. ,, Center table on drill press. There are two 5/,. slots on each side of base for secudng to dn'll press. • If drill press table has T-slots, use four T-nut clamp assambliss, two on each side, to secure milling table. Clamp assemblies are not supplied. • If drill press table has slots to fit T-nuts, use four bolts with heavy washem (not supplied) and attach T-nuts to bottom of table. Secure milling table w_th locking nuts (not supplied). • Make sure workpiaces, guides, fences, or power heads are securely clamped, as applicable, Do not force accessory. Be positive you are feeding in right direction. • Never feed "_ree-hancF without table guide and/or guides. Use vises or appropriate clamps to secure each workplace, securely clamping them to work surface. • If drill press table does not have T-slots or threaded holes, drill and tap four holes, matching location of %" slots in base. Fasten milling table with four bolts and heavy washsis (not supplied). SPECIFICATIONS • Use only accessories designed for mill. Keep power tool guard in place. Dress properly. Do not wear jewelry, gloves, or loose clothing. • Wear a face shield or safety glasses. Never place hands in jeopardy. Table .................................... T-Slots ....................................... T-Slots (center to center) ........................ Longitudinal Travel .............................. Check for shipping damage. If damage has occurred, a claim must be filed with carrier immediately. Check for completeness. immediately report missing parts to dealer. Cross Travel ................................... Value NOTE: The tool has been coated with a protective coating. in order to ensure proper fit and operation, the coating must be removed. Removed coating with mild solvents, such as mineral spirits, and a soft cloth. Nonflammable solvents are recommended. After cleaning, cover all exposed surfaces with a light coating of oil. Be sure to lubricate table as described in "Maintenance". of One Division ........................ 18'/, x 6" %=" 2%_" 12" 8" 0,0008" Cross Travel per One Revolution .......................... Longitudinal Travel per One Revolution 2 0.0787" .......................... 0.0787" U-CLAMP INDEXING • U-clamp can be used to clamp thicknesses up to 2". • Index collar rotates with handwheel but can be repositioned to calibrate table feed, Position table at a convenient reference point. • Position workpiece; it should rest flat on table prior to clamping. • For clamping, use edge of U-stamp which is closest to ball joint because a greater force is created at this edge. TABLE MOTION • Turn handwheel to move table opposite to the direction which it will travel. Slowly turn handwheal to bdng table back to reference point. This wili take out play in feed • Make sure U-clamp can rest on workpisce and table with hole in ball joint over a slot in table. • Slide stud with T-nut into slot. screw. • Hold handwheal steady and rotate index collar to align it with scale. • Slide U-clamp over stud and into position to clamp on as much of the workpiece as possible. • Screw the flange nut onto stud. • Index collar can be calibrated to inc_cate relative distance traveled in same direction. Collar must be indexed again to accurately indicate distances in opposite direction. • Make sure T-nut is properly shouldered in slot and the stud is perpendicular to table. OPERATING • Tighten flange nut to securely clamp workpisce. Refer to Figure 1. • T-NUT • For a proper clamping configuration, T-nut should be shouldered within T-nut slot or open slot of work table. • T-nut must be connected stops: • With screw a T-slotted inserting • With to threaded table, studs should stops. • be connected before stud with T-nut into table. an open slotted ADJUST break cutter, Direction of feed should ter rotation. through cuts. It may "grab" and ruin or damage during always milling using a cutter with a different slot. speed of cutter • POSITION equipment.'The Covering rotation, the opening be against operation. number or by adjusting • Tighten center required. Motion from side te side is adjusted with longitudinal feed screw by turning handwheal on either side. direction Correct of cut- this by of teeth, by changing feed of cuL over cross feed screw in front and back, is recommended from dropping on threads of screw • Motion toward or away from operation is adjusted with cross feed screw by turning handwheel on the front. • to take heavy • Avoid vibration table, studs san not be connected until after stud with T-nut is inserted Do not attempt your workpisce, choice of cut must be proportional to dgidity of set up, capability of equipment, choice of milling cutter, and hardness of workplace. stud. T-nut has thread stud into T-nut until thread GUIDELINES (Key No. 21), to prevent any chips and on table base. set screw (Key No. 25) to secure position if • Use handwheels to move table to desired position. Make sure that table motion is smooth, Adjust wear plates if necessaFy. ADJUST Refer to Figure • Wear plates • After completing each milling operation, clean all chips off table and out of T-slots with a hard bristle brush. PLATES WEAR • Keep threads 1. (Key No. 16) are used to minimize play within guide grooves. • Wear plates should be s_usted to produce a uniform Both wear plates • Loosen • Adjust should be adiusted an equal amount of torque to each set screw (Key Nos. 23 and 25) st each end of the wear plates. Adjust the screws until a slight drag is felt when • rotating the handwheeL Lock set screws into position by holding L- wrench and tightening position oiled sur[aces and moving parts • Periodically turn handwheels to move table right and left, back and forth, and full length o1 travel. This will keep the Milling Table in good working condition. in the same manner. he)( nuts (Key No. 24), drag of wear plate by applying feed screws matter. • KeeP table top, all machined lubricated, drag for entire length of travel. • of cross and longitudinal and free of foreign with an hex nuts. 3 Model351.275931 Figure 1 - Replacement Parts Illustration for Compound Milling Table 10 _" 1_1 12 13 2O 19 12 KEY NO. PART NO. DESCRIPTION QTY, 1 09900.00 Base 1 2 10281.00 Saddle 1 3 10282.00 Table 1 4 10283.00 Collar 2 5 01531.00 4 x 4 x 10ram Key 3 8 00964.00 6-1.0 x 6ram Set screw 2 7 8 10284.00 01279,0() Longitudinal feed screw Spring plate 1 3 9 10286.00 Handle 3 10 10287.00 Handle Screw 3 11 01282.00 8-1.25 x 6ram Set screw 3 12 01281.00 Locking nut 3 13 10289.00 Handwheel 3 14 15 10175.00 09884.00 Graduated collar YJ"Bail 3 2 16 09903.00 Wear plate 2 17 01822.00 8-1.25 x 20ram Socket head bolt 6 18 10178.00 Longitudinal bracket 2 19 STD852008 8ram Lock washer* 2 20 ! 0179.00 Cross feed bracket 1 21 22 10090.00 10091,00 Cross feed screw Cross feed nut 1 1 23 18385.00 6-1.0 x 25rnm Set screw 2 24 STD840610 6-1.0ram Hex nut* 6 25 05110.00 6-1.0 x 20ram Set screw 4 z_ 25134 2-Piece U-Bolt Clamp Set 1 /_ 16305.01 Operator's Manual 1 Standard hardware item available locally "_ Not Shown In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME °" (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 Au Canada pour tout le service - 1-877-LE-FOYER" (1-877-533-6937) For the repair or replacement parts you need: Call 6 a.m. - 11 p.m. CST, 7 days a week PartsDirect 1-800-366-PART (1-800-366-7278) www.sears.com/partsdirect Para ordenar piezas con entrega a domicilio - 1-800-659-7084 For the location of a Sears Service Center in your area: Call 24 hours a day, 7 days a week 1-800-488-1222 To purchase or inquire about a Sears Maintenance Agreement: Call 7 a.m. - 5 p.m. CST, Monday - Saturday 1-800-827-6655 r • HomeCentral
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 6 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Aug 14 23:54:19 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools