Craftsman 706139910 User Manual TOOL CHEST Manuals And Guides L1003087
CRAFTSMAN Tool Chest Manual L1003087 CRAFTSMAN Tool Chest Owner's Manual, CRAFTSMAN Tool Chest installation guides
User Manual: Craftsman 706139910 706139910 CRAFTSMAN TOOL CHEST - Manuals and Guides View the owners manual for your CRAFTSMAN TOOL CHEST #706139910. Home:Tool Parts:Craftsman Parts:Craftsman TOOL CHEST Manual
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
@
Owner's
Manual
STATIONARY
UNIT
WARNINGS
AND CAUTIONS:
- DO NOT stud on this product You may fail which may cause personal injury,
• WEAR SAFETY GLASSES AND GLOVES when cutting the banding material, The
STOOGE
.
bands may snap which may cause personal injury.
BE CAREFUL when opening more than one drawer, The product may become
uns_ble and tip, which may cause personal injury or product damage,
DO NOT mount this product on a truck bed or any other moving object This may
cause personal injury or product damage,
DO NOT step in the dra'_rs. You may fall which n_y _use
personal injury,
. Appropriately _ure
this product before moving it _th a forklift,
. DO NOT alter this product in any manner, For example, do not weld external Iockbars
or attach electfica_ equipment, This may cause product damage or personal inju_.
Ciose the drovers and doors before moving this product, The dr_rs
or doors could
come open and make the product unstable and tip, which may cause personal injury
or product damage.
. The maximum weight for each drawer should be no more than 50 pounds.
. Weight limit an the top of the workbench is t ,00O pounds, if the limit is exc_
the
product could collapse and cause _rsonal injury or product damage.
r
.....
ii,
;.........
_.........
........
........
•
.....................
....
......................
...............................
CaUi 1o800-366-7278
Service Parts
PARTS:
STATIO_R¥
Stationary
Storage Unit
KEY
A
B
C
D
E
F
G
H
Stationary
Storage Unit Ii
Refer
STOOGE UNIT
DESCRIPTION
SiDE
CENTER SUPPORT
9" D_WER
ASSY,
4" DRAWER ASSY,
2" DRAWER ASSY
F4AE_,
SHELF
TOP
to Service
for
Parts
Drawing for fu!l listing
of Service
Parts
qTY.
2
4
2
9
2
6
2
1
NOTE: Slides wot shown.
CAUTION:
Read
and follow
STATIONARY
all
KEY
A
B
C
D
E
F
G
t{
Safety Rules and Operating
instructions
before first use
of this product.
Sears, Roebuck
and Co., Hoffman Estates,
IL 60179 USA
STORAGE
UNIT II
DESCRIPTION
SiDE
CENTER SUPPORT
9" DRAWER ASSY.
4" DRAWER ASSY
2" D_WER
ASSY.
R4IL
SHELF
_TOP
QTY,
2
2
1
2
2
4
2
t
A -\.
c
Made in the U,S,A.
Fg07A1
NOTE: Varies slightly from
picture. Slides and door not
shown.
2
HARDWARE:
(Hard.re
depe_ant
_}
_
6)
@_,_ "/4_,20 X V2 Tamper Proof Screw
O
_
ASSEMBLY:
STATIO_Y
UNIT:
Attach the center supports (B) to
of the rails (F) using sixt_n 1/4hex screws and sixteen 1/4_20
Finger tighten.
SIo[[ed "f_''":_-
ASSEMBLY:
until the top is in place.
- Attach the rail and center support
assembly to the side using one 1/4_20 x
7/16 hex screw and one 1/4-20 nut per
comer at the top joints, Attach the bottom
joints with two 1/4-20 x 7/16 hex ssrevcs
and nuts. _TE:
For Stationary
Storage Unit attach the middle rails to
each side _th _
1/4-20 x 7/16 hex
This unit has six rails and four _nter
suppers.
the center
20 x 7/16
hex nuts,
the top and bottom channels of the
drawer slides,
_TE:
Do not insert screws in the top
holes of t_ side and rail assemblies
SUPPORT
STORAGE
screws
tighten.
and nuts per joint,
Finger
._
?;
.
• Place the rear of the outside slide at the
rear of the unit, line up the holes and
attach the slide with tw'3 1/4-20 x 7/16
hex screws and _
1/2=20 hex nuts,
Finger tighten, Attach the remaining
slides leaving a gap between them
according to the dra_r
size.
- Before instaJling the inside slide, lubricate
the top and bottom channels of the
outside slide.
- Guide the inside slide into the channel at
a_mblies
are for Stationary
Unit II only.
DOOR
The open areas between the center
supports (B) and sides (A) must
measure 18 1/2" for proper fit of the
drav,_rs, Square up the frame and
wench tighten the screws,
STATIONARY STORAGE UNIT I1:
This unit has four rails and tv_ center
• Place the top (H) on the rail and side
assembly; line up the four hobs and
attach the top using four 1/4-20 x 7/16
hex screws and 1/4-20 hex nuts.
o The door catch, lock, a_ mounting
hard.re
is in a _parate bag,
• Remove the knockouts from the front
end panel on the side that the d_r is to
be hung,
Position the door on the side of the work
bench opening se!ected and line up the
holes on the hinge and the bench front,
/!
°
• Wrench tighten all screws and nu_s.
• Move the unit to a permanent location,
3
ASSEMBLY:
the door hinge screws are tightened
they cannot be removed with a
screwdriver.
i°
supped& Make sure that the slots in the top
rail are on top and the slots in the bottom
rail are dove, and that the word "Top" on
the center supports is toward the top,
Attach the center supports (B) to the rails
(F) using two 1/4-20 x 7/16 hex screv_ and
t/4-20 hex nuts per joint Finger
tighten.
Storage
NOTE: The door may be mounted on
either side of the unit, CAUTION: O_e
TOP ASSEMBLY:
F
Install the drawer by in_rting the drawer
slides into the instalbd siide assemblbs
Make sure that the slides on both sides
line up, Push the drav_r until it is fully
close, The dra_,-_r is now securely in
place Repeat the procedure for the
remaining drawers.
NOTE: Door, lock, and door catch
the front end of the outside slide. R_ly
push the inside slide past the slide stop
on the outside slide. Repeat this step for
the remaining slides.
21--_
Slot
bole
INSTALLATION:
Before instaJling the drawers, lubricate
Hole
These instructions pertain to two units.
Most of the steps relate to both units;
however, the specific unit will _ called out if
the assembly belongs only to iL
CENTER
D_WER
the top or the bottom oftl_ unit a_
work to_rd
the other end.
_,_2_x 7,,I_He×screw
AND
ASSEMBLY:
NOTE: These units are designed so that
the drawers and shelves may be
positioned to suit your needs. During
installation of" the slides, start at either
1'4-20 X t/2 Slei_ed Screw
SIDE
RAIL
SLIDE
Slotted
iqole
on model)
4
• Attach the door with _
I/4-20 tamper
proof screws and two 1/4-20 hex nuts,
Finger tighten. Do not wrench tighten
until the door lock is adjusted to the door
_tch,
LOCK
ASSEMBLY:
SHELF
ASSEMBLY:
. Rr_ a desired iocatJon _r tl'_ sf_f, line up
t_ fc4Jrhel_ in the _f_
the ho4es in
the side and _ter
sup_.
Attach the
shelf usi_ four !/4-20 x 7/16 _
scre/cs
_d four t/4-20 hex nuts. Wrench tighten.
Repeat the pr_e
,,Mththe other _f,
,, insert the lock assembly (keeping the
locking cam verticai) into the rectangular
hole on the door.
° Position the retaining clip in the slots of
the _ock on the inside of the door,
• Strike the flat edge of the clip v_th a
manet to seat,
@
REMOVING
DRAWERS:
AND INSTALLING
Fully extend the d_f.
Then push it _k
a _tien
of an inch.
• tns_ a screwdriver into the s!ot in the slide
and depress the stop until it dears the lan_.
Repeat the _ure
for the other sli_,
P_,_r_e the drav_r,
o To remove the lock u_
a screwdriver
to
drive out the retaining clip.
DOOR
.
CATCH
ASSEMBLY:
Mount the door catch opposite the door
hinge in the upper hole _th one I/4-_
round head machine _rew and one 1/420 hex nut,
• Square up the door and the catch,
Wrench tighten all of the screws.
Lubricate
• To rein_atl the drav_t_r,pry the stop far
e_
out to engage the lan_ (3/16" to
1/4") and I_
the dra_,er onto the sli_s
unti_the st_s _
_
the lar_ses,
An auto wax _il p_serve _ stor@ unifs
hi_ lusl_ finish. ,_4_Y the wax as to a car.
wax _,4tI_p prot_l the unit _inst
_ratch_,
o Lubricate sli_
_c_ yearly,
Grea_ ar_ oil _
be removed _th rr_st
Catch
st_rd
cleaning fluids. For safety, use a
non fiam_le
cleaning fluid,
INTENTIONALLY
LEFT BLANK
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 3 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Sat Mar 29 12:31:27 2014 Author : Title : Subject :EXIF Metadata provided by EXIF.tools