Craftsman 706208810 User Manual TOOL CHEST Manuals And Guides 1501203L
User Manual: Craftsman 706208810 706208810 CRAFTSMAN TOOL CHEST - Manuals and Guides View the owners manual for your CRAFTSMAN TOOL CHEST #706208810. Home:Tool Parts:Craftsman Parts:Craftsman TOOL CHEST Manual
Open the PDF directly: View PDF .
Page Count: 8
Download | ![]() |
Open PDF In Browser | View PDF |
OPERATOR'S MANUAL T HEAVY DUTY TOOL ° • Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water. • Auto wax will preserve the unit's luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches. • Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid. • If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners may be cleaned with soap and water. CHESTS DANGER ,A is used to indicate a hazardous situation which, if not avoided, will result in serious injury or death. WARNING z_ indicates a hazardous situation which, if not avoided, could result in serious injury or death. CAUTION is used to indicate a hazardous situation which, if not avoided, m_m_a_y_ result in minor injury, moderate injury, or property damage. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. * Product you purchased may vary from picture shown CALL 1-800-366-7278 FOR SERVICE PARTS. Refer to Service Parts Drawing for full listing of Service Parts. LOCATING MODEL # iNFORMATiON Model numbers and other information required for service parts is located on a label on the interior right side of the top most drawer. • The maximum weight for each drawer should be no more than 75 Ibs. • The maximum product weight, including contents, should be no more than 650 Ibs. for each model combination with 4.5 x 1.5 inch casters. The maximum product weight, including contents, should be no more than 1,000 Ibs. for each model combination with 5 x 2 inch casters. Ball bearing slides • For casters, use high quality bearing grease, (yearly). • Lubricate the slides with grease or equivalent,(twice yearly.) • Lubricate lock with graphite, (yearly). Distributed by Sears Brands Management Corporation, DANGER ,_ • DO NOT stand on this product. You may fall or cause product to tip. • DO NOT open more than one drawer. The product may become unstable and tip. • DO NOT step in the drawers. You may fall or cause product to tip. • DO NOT mount this product on a truck bed or any other moving object. • DO NOT move the product prior to closing and locking all the drawers and chest lid. The drawers could come open and make the product unstable and tip. • DO NOT place any objects on top of chest lid. Remove all objects from chest lid before opening. WARNING /!k • WEAR SAFETY GLASSES when removing or repositioning the slides. • DO NOT pull the unit, push it when moving • USE THE BRAKES when not moving this product. This will prevent the product from rolling. • DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. • Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface. • BE CAREFUL when closing the cover. Remove hands before the cover closes completely. CAUTION • This product is not designed to be directly lifted with a fork lift, or to be towed with any mechanical devices. • The maximum weight for each drawer should never be exceeded. • Only transport this product empty. Properly secure when transporting. • DO NOT exceed maximum product weight, including contents. See Capacities for more information. Hoffman Estates, JL60179 F1913A1 CASTER iNSTALLATiON TOOLS REQUIRED: (264NCH CABINET) items Needed: #14 - 10 x 5/8-in Hex Screws (Qty: 16) 3/8-in Wrench 3/8-in Wrench 7/16-in Wrench Cross-tip Screwdriver HARDWARE INCLUDED: 26=INCH CABINET HARDWARE #14 (Qty:- 16) 10 x 5/8-in Hex Screws (Qty:- 4) #14 10 x 3/4 Cross-tip Screw HARDWARE INCLUDED: 40=INCH CABINET HARDWARE Process: NOTE: Use adequate personnel for this operation. NOTE: Failure to install caster angles may result in premature cabinet failure. • Place the unit on its top. Use packaging material to protect the paint finish. • Position caster angles on the cabinet. Flanges should be toward the inside and pointed up. • Attach casters and caster angles using (4) #14 - 10 x 5/8 Hex Screws for each caster. Mount both swivel casters on the same side of the cabinet as the side handle. • Wrench tighten all screws. Do not overtighten. • Return the unit to its upright position. Caster angles (flanges inside) #14 - 16) 10 x 3/4-in Screws (Qty: 1/4 - 20 x 5/8 Screw (Qty: 16) 1/4-in Nut (Qty: 16) CASTER iNSTALLATION (404NCH CABINET) Items Needed: 1/4 - 20 x 5/8 Screw (Qty: 16) 1/4-in Nut (Qty: 16) 7/16-in Wrench NOTE: Not all assembly instructions will relate to your model. SiDE HANDLE ATTACHMENT Items Needed: #14 - 10 x 3/4 Cross-tip Screw (Qty: 4) Cross-tip Screwdriver Process: ° Attach the side handle using (4) #14 - 10 x 3/4 Cross-tip screws. • Hand tighten. Do not overtighten. t Process: NOTE: Use adequate personnel for this operation. ° Remove the bottom drawer by following the drawer removal instructions. • Lay the cabinet down on its back. Use packaging material to protect the paint finish. • Mount both swivel casters on the same side of the cart as the side handle. • Attach each caster using (4) 1/4-20 x 5/8 screws and (4) 1/4" nuts per caster. • Wrench tighten all screws. • Return the cart to its upright position. 1/4-in Nut 1/4-20 x 5/8-in Screw © LABELS (iFAPPLICABLE) Process: • Apply a light film of glass cleaner to the surface where the label is to be applied. ° Peel the label from the backing and place the label in position. ° Check alignment of the label and adjust accordingly. ° Hold the label in position and squeegee off excess liquid with a towel, working from the center toward each end of the label. ° Suggested label location is shown. iNSTALLiNG DRAWERS Ball bearing slide - Pull slides and slide carrier out to fully extended position (see illustration.) Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide. Open drawer and reclose to ensure proper operation. slide carrier U- / slide REMOVING DRAWERS ° Empty the drawer. • Fully extend the drawer. Release REMOVING Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops). Pull out to remove. AND iNSTALLiNG SLIDES To remove the slide from the unit, first remove the drawer. ° After removing the drawer check to see if the unit has rivets located on the front of the slide. To drill out rivets, use a 5/32-in drill bit. The rivets will need to be replaced with 5/32-in rivets. ° To reinstall the slide in the appropriate position in the unit, align front and back lances with mounting holes in the side of the unit. Pull towards the front of the unit and downwards until rivet holes in slide line up with holes in the unit. The rivets will need to be replaced with 5/32-in rivets. ° For smooth operation, make sure the drawers are matched with their original slides. \\ Drill out rivet \\\ \ \ \ MANUAL DE USUARIO CRRFT MIIH ° CAJAS DE HERRAMIENTAS DE TRABAJO PESADO • Limpie con detergente suave y agua los frontales y los bordes laterales de los cajones y las demos superficies. • La cera para autom6vJJes preservar_ el acabado briJJoso de Jaunidad. Aplique la cera como Io hada al carro. La cera tambi6n ayudar_ a proteger la unidad contra raspones. • La grasa y el aceite pueden retirarse con la mayoda de los liquidos est_ndar para limpieza. Por razones de seguridad, utilice un liquido incombustible para limpieza. • Si se suministran forros para las gavetas, se recomienda que se utilicen para proteger el acabado interno de Jas mismas y para faciJitar Jalimpieza. Los forros para gavetas pueden limpiarse con agua y jab6n. PEUGRO _, peJigrosa que, se utiJiza para indicar de no evitarse, ADVERTENCiA evitarse, resuJtar_ z_ podria producir PREOAUOKSN no evitarse, propiedad. indica Jesiones una situaci6n graves se utiJiza para indicar puede derivar una situaci6n en Jesiones graves peJigrosa que, de no o Ja muerte. una sJtuaci6n en Jesiones o Ja muerte. peJigrosa Jeves o moderadas, que, de o en daSo a Ja ATENCI(SN: Lea y siga todas Jas Normas de Seguridad y Jas Jnstrucciones de Funcionamiento antes de utiJizar por primera vez este producto. PELIGRO ,_, • NO se ponga de pie sobre esta unidad. Puede caerse u ocasionar que el producto se vueJque. • NO abra m_s de una gaveta. El producto podria quedar inestabb voJcarse. * El producto que compraste EN ESTADOS PiEZAS UNIDOS DE REPUESTO. puede variar de la imagen que se muestra LLAME FUERA LLAME A SU DJSTRiBUJDOR modeJo aJcomunicarse. UBICACION AL 1=800=659-7084 DE JNFORMACl6N DE ESTADOS LOCAL. PARA UNiDOS Suministre el nQmero de y • NO utiJice Jas gavetas como peJdaSos. Puede caerse u ocasionar que el producto se vueJque. • NO monte este producto en una cama de carro o ninguin otro objeto m6vJJ. • NO mueva la unidad antes de cerrar y asegurar todas Jas gavetas y la tapa del baOl. Las gavetas podrian abrirse y hacer que la unidad se vuelva inestable y se vuelque. • NO coloques ningOn objeto sobre la tapa del baOl. Quita todos los objetos de la tapa del baOl antes de abrirlo. DEL NO. DE MODELO El nQmero de modeJo y demos informaci6n requerida para Jas piezas de servicio se encuentran en una etiqueta en el Jado interior derecho de Ja gaveta superior. ADVERTENCIA Z_ • USE GAFAS correderas. • NO DE jaJe Ja unJdad, SEGURJDAD empQjeJa cuando • UTJUCE LOS FRENOS cuando Esto impedir_ que se desJice. • El peso m_ximo en cada gaveta no debe ser mayor de 34,05 kg. • El peso m_ximo deJ producto, incJuyendo el contenido, no debe ser mayor de 295 kg para cada combinaci6n de modeJo con ruedas de 11.43 x 3.81 cm. El peso m_ximo deJ producto, induyendo el contenido, no debe ser mayor de 454 kg para cada combinaci6n de modeJo con ruedas de 12.7x 5.08 cm. • NO aJtere Ja unJdad de sujeci6n externas • Mantenga Ja unidad inestabJe niveJada. • TENGA tapa y voJcarse cuidado cierre al quitar en modo o volver a poner Ja mueva. el producto aJguno. no est6 en movimiento. Por ejempJo, no sueJde ni Je incorpore equipos eJectricos. en superficies niveJadas. La unidad si se aJmacena cuando cJerre las o se moviJiza Ja tapa. Quite puede Jas barras tornarse en una superficie Jas manos antes no de que Ja compJetamente. PRECAUCJON F Cojinetes de bolas ° Este producto no est_ diseSado para ser bvantado directamente con un montacargas, ni para ser remoJcado con unidades mecanizadas. ° Nunca debe exceder el peso m_ximo de cada gaveta. ° S6Jo transporte esta unidad cuando est6 vacia. AsegQreJa adecuadamente cuando Jatransporte. ° NO exceda el peso m_ximo deJ producto, incJuyendo el contenido. Refi@ase a Jas Capacidades para m_s informaci6n. • Para Jas ruedas, utiJice grasa para rodamientos de aka caJidad (anuaJmente). • Lubrique Jas guias con grasa o equivaJente (dos veces por aSo). • Lubrique Jacerradura con grafito (anuaJmente). Distribuido cerca Sears Brands Management Corporation, Hoffman Estates JL60179 F 1913A1 INSTALACION HERRAMENTAS NECESARIAS: Elementos necesarios: Tornillo Hexagonal de No. 14 - 10 x 5/8 (Cant.: 16) Llave Allen de 3/8 pig Llave Inglesa de 3/8 inch Llave Inglesa de 7/16 inch Destornillador de Punta en Cruz PIEZAS INCLUIDAS: FERRETERIA PARA GABINETE DE 26 PULG. xTornillo 5/8 (Cant: Hexagonal 16) de No. 14 - 10 3/4 (Cant: 4) Tuerca Phillips de No. 14 - 10 x PIEZAS INCLUIDAS: FERRETERIA PARA GABINETE DE LAS RUEDAS (26 PULG. GABINETE) DE 40 PULG. NOTA: Utilice personal adecuado para esta operaci6n. NOTA: No instalar los angulos de las ruedas puede ocasionar falla prematura del gabinete. ° Coloque la unidad sobre su parte superior. Utilice el material de empaque para proteger el acabado de la pintura. • Ubique los &ngutos de las ruedas en el gabinete. Las pesta5as deben ir hacia el interior y apuntando hacia arriba. • Fije las ruedas y los &ngulos de las ruedas utilizando (4) tornillos hexagonal No. 14 - 10 x 5/8 para cada rueda. Monte ambas ruedas giratorias en el mismo lado del gabinete donde se encuentra la manija lateral. • Apriete todos los tornillos con una Ilave. No apriete demasiado. • Vuelva a colocar la unidad en su posici6n vertical. (pestaSas [__ I Angulos de ruedas hacia adentro) No. 14 4) - 10 x 3/4 Tomillo (Cant: No. 1/4 - 20 x 5/8 Tomillo (Cant: 16) 1/4 Tuerca (Cant: 16) INSTALACION DE LAS RUEDECILLAS: (40 PULG. GABINETE) NOTA: No todas las instrucciones de ensamblaje se refieren a tu modelo. INSTALACION DE LA MANIJA LATERAL Elementos necesarios: Tornillos Phillips de No. 14 - 10 x 3/4 (Cant.: 4) Destornillador de Punta en Cruz Proceso: ° Fije la manija lateral usando 4 tornillos de Punta en Cruz de No. 14 - 10 x 3/4. • Apriete a mano. No apriete demasiado. t Elementos necesarios: No. 1/4 - 20 x 5/8 Tomillo (Cant: 16) 1/4 Tuerca (Cant: 16) Llave Inglesa de 7/16 inch NOTA: Use la ayuda de otras personas para esta operacion. • Quite la gaveta inferior siguiendo las instrucciones para retirar las gavetas. • Acueste el carro sobre su parte trasera. Proteja el acabado con el material de embalaje. • Instale las dos ruedecillas giratorias en el mismo lado del carro. • Asegure las ruedecillas usando cuatro tornillos de 1/4-20 x 5/8 y cuatro tuercas de 1/4" en cada una. • Apriete todos los tornillos con una Ilave de tuercas. • Vuelva a colocar el carro en su posici6n vertical. 1/4" Tuerca 1/4-20 x 5/8" Tornillo ETIQUETAS INSTALACION (Sl APLICA) Proceso: • Aplica una capa fina de limpiador para vidrios en la superficie donde se colocar_ la etiqueta. • Quite el revestimiento de la etiqueta y col6quela en su sitio. • Revise el alineamiento de la etiqueta y ajQstelo segQn sea necesario. • Sostenga la etiqueta en su lugar y elimine el exceso de liquido con una toalla, empujando desde el centro hacia cada extremo de la etiqueta. DE GAVETAS Correderas de rodamientos esf_ricos -jale hacia afuera las correderas y el soporte de las correderas hasta que queden en posiciOn totalmente extendida (ver ilustraci6n). Sostenga la corredera en el gabinete mientras Io alinea con la corredera de la gaveta. Soporte de las correderas i U Corredera __-- __-::--:-: ...... - _-:_-_q:- _ :7:......... REMOCI6N DE GAVETAS ° Vacie la gaveta. ° Abra completamente la gaveta. Libere INSTALACION Estilo palanca - Levante o baje (dependiendo de la corredera) la palanca de NberaciOn en ambos lados (esto permite que las correderas pasen sobre los topes.) Jale hacia afuera para retirar. Y DESINSTALCION DE CORREDERAS • Para quitar la corredera de la unidad, primero quite la gaveta. • Despu6s de quitar el cajOn, comprueba si la unidad tiene remaches en el frente de la corredera. Para quitar los remaches con un taladro, usa una broca para taladro de 5/32 pig. Deber_s reemplazar los remaches con remaches de 5/32 pig. • Para volver a instalar correctamente la corredera en la unidad, alinea las lancetas frontales y posteriores con los orificios de montaje en el lado de la unidad. El tir6n hacia el frente de la unidad y hacia abajo hasta agujeros de remache en la diapositiva se alinea con agujeros en la unidad. Deber_s reemplazar los remaches con unos de 5/32 pig. • Para un buen funcionamiento, cerci6rese de que los cajones hacen juego con sus correderas originales. \ Saca el remache con el taladro \\\ \
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Sat Jan 24 07:02:59 2015 Author : Title : Subject :EXIF Metadata provided by EXIF.tools