Craftsman 706449601 User Manual TOOL CHEST Manuals And Guides 1501321L
User Manual: Craftsman 706449601 706449601 CRAFTSMAN TOOL CHEST - Manuals and Guides View the owners manual for your CRAFTSMAN TOOL CHEST #706449601. Home:Tool Parts:Craftsman Parts:Craftsman TOOL CHEST Manual
Open the PDF directly: View PDF .
Page Count: 8
Download | |
Open PDF In Browser | View PDF |
OPERATOR'S MANUAL T ° • Lubricate lock with graphite, (yearly). • Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water. • Auto wax will preserve the unit's luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches. • Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid. • If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners may be cleaned with soap and water. DANGER ,A is used to indicate a hazardous situation which, if not avoided, wiJ.JI result in serious injury or death. WARNING z_ indicates a hazardous situation which, if not avoided, could result in serious injury or death. CAUTION is used to indicate a hazardous situation which, if not avoided, may result in minor injury, moderate injury, or property damage. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. * Product you purchased may vary from picture shown CALL 1-800-366-7278 FOR SERVICE PARTS. Refer to Service Parts Drawing for full listing of Service Parts. LOCATING MODEL # iNFORMATiON Model numbers and other information required for service parts is located on a label on the interior right side of the top most drawer. • The maximum weight for each drawer should be no more than 100 Ibs. • The maximum product weight for each model combination, including contents, should be no more than 1,200 Ibs. Ball bearing slides DANGER _, • DO NOT stand on this product. You may fall or cause product to tip. • DO NOT open more than one drawer. The product may become unstable and tip. • DO NOT step in the drawers. You may fall or cause product to tip. • DO NOT mount this product on a truck bed or any other moving object. • DO NOT move the product prior to closing and locking all the drawers and chest lid. The drawers could come open and make the product unstable and tip. • DO NOT place any objects on top of chest lid. Remove all objects from chest lid before opening. WARNING /!k • WEAR SAFETY GLASSES when removing or repositioning the slides. • DO NOT pull the unit, push it when moving • USE THE BRAKES when not moving this product. This will prevent the product from rolling. • DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. • Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface. • BE CAREFUL when closing the cover. Remove hands before the cover closes completely. CAUTION • This product is not designed to be directly lifted with a fork lift, or to be towed with any mechanical devices. • The maximum weight for each drawer should never be exceeded. • Only transport this product empty. Properly secure when transporting. • DO NOT exceed maximum product weight, including contents. See Capacities for more information. • For casters, use high quality bearing grease, (yearly). • Lubricate the slides with grease or equivalent,(twice yearly.) Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 F1975 TOOLS REQUIRED: _ REMOVING DRAWERS • Empty the drawer. • Fully extend the drawer. Cross-tip Screwdriver HARDWARE Release INCLUDED: (Qty:- 4) #14 10 x 3/4 Cross-tip Screw Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops). Pull out to remove. NOTE: Not all assembly instructions will relate to your model. SiDE HANDLE ATTACHMENT Items Needed: #14 - 10 x 3/4 Cross-tip Screw (Qty: 4) Cross-tip Screwdriver Process: ° Attach the side handle using (4) #14 - 10 x 3/4 Cross-tip screws. • Hand tighten. Do not overtighten. t O INSTALLING DRAWERS Ball bearing slide - Pull slides and slide carrier out to fully extended position (see illustration.) Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide. Open drawer and reclose to ensure proper operation. Slide carrier / Slide REMOVING AND iNSTALLiNG SLIDES • To remove the slide from the unit, first remove the drawer. • After removing the drawer check to see if the unit has rivets located on the front of the slide. To drill out rivets, use a 5/32-in drill bit. The rivets will need to be replaced with 5/32-in rivets. • To reinstall the slide in the appropriate position in the unit, align front and back lances with mounting holes in the side of the unit. Pull towards the front of the unit and downwards until rivet holes in slide line up with holes in the unit. The rivets will need to be replaced with 5/32-in rivets. • For smooth operation, make sure the drawers are matched with their original slides. \\\\\\ Drill out rivet \\\ \ \ J / / MANUAL DE USUARIO CRRFT MIIH ° • Lubrique la cerradura con grafito (anualmente). • Limpie con detergente suave y agua los frontabs y los bordes laterales de los cajones y las demos superficies. • La cera para autom6viles preservar_ el acabado brilloso de la unidad. Aplique la cera como Io haria al carro. La cera tambi6n ayudar_ a proteger la unidad contra raspones. • La grasa y el aceite pueden retirarse con la mayoria de los liquidos est_ndar para limpieza. Por razones de seguridad, utilice un liquido incombustible para limpieza. • Si se suministran forros para las gavetas, se recomienda que se utilicen para proteger el acabado interno de las mismas y para facilitar la limpieza. Los forros para gavetas pueden limpiarse con agua y jab6n. PEUGRO _, peligrosa que, de no evitarse, ADVERTENClA evitarse, se utiliza para indicar resultar_ en lesiones ,4X podria producir PREOAUOKSN no evitarse, indica lesiones se utiliza puede derivar una situaci6n graves una situaci6n graves para indicar que, de no o la muerte. una sJtuaci6n en lesiones o la muerte. peligrosa peligrosa leves o moderadas, que, de o en daSo a la propiedad. ATENOION: Lea y siga todas InstruccJones producto. de Funcionamiento PELIGRO ,_, las Normas antes de Seguridad de utilizar y las por primera vez este • NO se ponga de pie sobre esta unidad. Puede caerse u ocasionar que el producto se vuelque. • NO abra m_s de una gaveta. El producto podria quedar inestabb volcarse. * El producto que compraste EN ESTADOS PIEZAS UNIDOS puede variar de la imagen que se muestra LLAME DE REPUESTO. FUERA LLAME A SU DISTRIBUIDOR modelo al comunicarse. UBICACION AL 1=800=659-7084 DE ESTADOS LOCAL. DE INFORMAClON PARA UNIDOS Suministre el nQmero de y • NO utilice las gavetas como peldaSos. Puede caerse u ocasionar que el producto se vuelque. • NO monte este producto en una cama de carro o ningQn otro objeto m6vJJ. • NO mueva la unidad antes de cerrar y asegurar todas las gavetas y la tapa del baOl. Las gavetas podrian abrirse y hacer que la unidad se vuelva inestable y se vuelque. • NO coloque ningOn objeto sobre la tapa del baOl. Quite todos los objetos de la tapa del baQI antes de abrirlo. DEL NO. DE MODELO El nQmero de modelo y demos informaci6n requerida para las piezas de servicio se encuentran en una etiqueta en el lado interior derecho de la gaveta superior. ADVERTENClA Z_ • USE GAFAS correderas. • NO DE jale la unJdad, • UTILICE • NO altere cuando cuando en modo alguno. ni le incorpore la unidad y volcarse en superficies si se almacena cuidado cierre o volver a poner las la mueva. el producto externas • Mantenga inestable nivelada. tapa al quitar no est6 en movimiento. que se deslice. la unJdad de sujeci6n • TENGA empQjela LOS FRENOS Esto impedir_ • El peso m_ximo en cada gaveta no debe ser mayor de 45,4 kg. • El peso m_ximo del producto para cada combinaci6n de modelo, incluyendo su contenido, no debe ser mayor de 544,8 kg. SEGURIDAD cuando cJerre Por ejemplo, equipos no suelde las barras electricos. niveladas. La unidad puede tornarse o se moviliza en una superficie no la tapa. Quite las manos antes de que la completamente. PRECAUCKSN Cojinetes • Para las ruedas, utilice grasa para rodamientos • Este producto no est_ disefiado para ser bvantado directamente con un montacargas, ni para ser remolcado con unidades mecanizadas. • Nunca debe exceder el peso m_ximo de cada gaveta. • $61o transporte esta unidad cuando est6 vacia. AsegQrela adecuadamente cuando la transporte. • NO exceda el peso m_ximo del producto, incluyendo el contenido. Refi@ase alas Capacidades para m_s informaci6n. de bolas de alta calidad (anualmente). • Lubrique las gu[as con grasa o equivalente Distribuido cerca Sears Brands Management (dos veces Corporation, por aSo). Hoffman Estates IL 60179 F1975 HERRAMIENTAS Destomillador NECESARIAS: _ de Punta en Cruz REMOCION DE GAVETAS • Vacie la gaveta. • Abra completamente la gaveta. Libere PIEZAS INCLUIDAS: [__ 3/4 (Cant: 4) TomiNo Phillips de No. 14 - 10 x NOTA: No todas las instrucciones refieren a tu modelo. INSTALACION de ensamblaje se Estilo palanca - Levante o baje (dependiendo de la corredera) la palanca de liberaci6n en ambos lados (esto permite que las correderas pasen sobre los topes.) Jale hacia afuera para retirar. DE LA MANIJA LATERAL Elementos necesarios: Tornillos Phillips de No. 14 - 10 x 3/4 (Cant.: 4) Destomillador de Punta en Cruz Proceso: • Fije la manija lateral usando 4 tornillos de Punta en Cruz de No. 14 - 10 x 3/4. • Apriete a mano. No apriete demasiado. INSTALACION DE GAVETAS Correderas de rodamientos esf_ricos =jale hacia afuera las correderas y el soporte de las correderas hasta que queden en posiciOn totalmente extendida (ver ilustraci6n). Sostenga la corredera en el gabinete mientras Io alinea con la corredera de la gaveta. Soporte de las correderas Corredera -_--_L_-_-----_ INSTALACION Y DESINSTALCION DE CORREDERAS • Para quitar la corredera de la unidad, primero quite la gaveta. • Despu6s de quitar el cajOn, comprueba si la unidad tiene remaches en el frente de la corredera. Para quitar los remaches con un taladro, usa una broca para taladro de 5/32 pig. Deber&s reemplazar los remaches con remaches de 5/32 pig. • Para volver a instalar correctamente la corredera en la unidad, alinea las lancetas frontales y posteriores con los orificios de montaje en el lado de la unidad. El tir6n hacia el frente de la unidad y hacia abajo hasta agujeros de remache en la diapositiva se alinea con agujeros en la unidad. Deber&s reemplazar los remaches con unos de 5/32 pig. • Para el buen funcionamiento, asegurese de que los cajones hacen juego con sus correderas originales. \ \\\ \ Saca el remache con el taladro \\\ \ \
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Feb 04 07:03:11 2015 Author : Title : Subject :EXIF Metadata provided by EXIF.tools