Craftsman 917258524 User Manual TRACTOR Manuals And Guides 1006756L

User Manual: Craftsman 917258524 917258524 CRAFTSMAN TRACTOR - Manuals and Guides View the owners manual for your CRAFTSMAN TRACTOR #917258524. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman TRACTOR Manual

Open the PDF directly: View PDF .
Page Count: 56

ODEL BER 917.258524 OWNER'S MANUAL

®Assembly

®Operation

®Customer Responsibilities

oService and Adjustments

®Repair Parts

CAUTION: Read and follow all safety rules and instructions before operating this equipment.

FOR CONSUMER ASSISTANCE HOT LIN E, CALL THIS TOLL FREE NUMBER: 1-800-659-5917

ib_l m

SAFETY RULES

_Safe Operation Practices for Ride-On Mowers

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWtNG OBJECTS_

FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

I. GENERAL OPERATION

•Read, understand, and follow all instructionstn the manual

and on the machlne before starting.

•Only allow responsible adults, who are familiar with the

instructions,to operate the machine..

•Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade.

-Be sursthe area isclear of otherpeople before mowingo Stop

machine if anyone enters the area.

•Never carry passengers,.

•Do not mow inreverse unless absolutely necessary, Always

look down and behind before and while backing..

•Be aware of the mower discharge directionand do notpoint

it at anyone. Do not operate the mower without either the

entire grass catcher or the guard in place.

•Slow down before turning.

•Never leave arunning machine unattended. Always turnoff

blades, set parking brake, stop engine, and remove keys

before dtsmounting_

oTurn off blades when not mowing.

•Stop engine before removing grass catcher or unclogging

chute,

•Mow only in daylight or good artificial llghL

•Do not operate the machine while under the Influence of

alcohol or drugs.

•Watch for traffic when operating near or crossing roadways.

°Use extra care when loading or unloading the machine into

a trailer or truck..

ii. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and

tipover accidents, which can result in severe injury or death.

All slopes require extra caution, if you cannot back up the

slope or if you feel uneasy on it, do not mow it.

DO:

o Mow up and down slopes, not across.

°Remove obstacles such as rocks, tree limbs, etco

•Watch for holes, ruts, or bumps. Uneven terrain could

overturn the machine. Tall grass can hide obstacles.

•Use slow speed. Choose a low gear so that you will not have

to stop or shift while on the slope.

oFollow the manufacturer's recommendations for wheel

weights or counterweights to improve stability..

•Use extra care with grass catchers or other- attachments.

These can change the stability of the machine,.

•Keep all movement on the slopes slowand gradual,. Do not

make sudden changes [n speed or direction.

°Avoid starting or stopping on a slope. If tires lose traction,

disengage the blades and proceed slowly straight down the

slope_

DO NOT:

•Donot turnon slopes unlessnecessary, andthen turnslowly

and gradually downhill, if poss bleo

•Do not mow near drop-offs, ditches, or embankments. The

mower could suddenly turn over if awheel is over the edge

of acliffor ditch, or if an edge caves in_

•Do not mow on wet grass, Reduced traction could cause

slidtng.

°Do not tryto stabilize the machine by putting yourfooton the

ground.

• Do not use grass catcher on steep slopes,

2

I!1. CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them°

°Keep childrenout of the mowingarea and under the watchful

care of another responsibleadult..

* Be alert and turn machine off ifchildren enter the area..

° Before and when backing, look behind and down for sinai(

children.

oNever cam] children. They may fail off and be seriously

injured or interferewith safe machine operation.

,Never allow childrento operate the machine.

°Use extra care when approaching blind comers, shrubs,

trees, or other objects that may obscure vision,

IV. SERVICE

= Use extracare inhandlinggasoline and otherfuels, They are

flammable and vapors are explosive_

Use onfyan approved container°

Never remove gas cap or add fuel with the engine

running. Aliow engine to cool before refueltng_ Do not

smoke.

- Never refuel the machine indoors_

-Never store the machine or fuel container inside where

there is an open flame, such as a water heater.

= Never run amachine inside aclosed area,

•Keep nutsand bolts, especially blade attachment botts,tight

and keep equipment tn good condition,

• Never tamper with safety devices. Check their proper

operation regularly.

° Keep machine free of grass, leaves, orother debris bu[Id-upo

Clean oil or fuel spiIlage_ Allow machine to cool before

stodng.

=Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

•Never make adjustments or repairs with the engine running.

• Grass catchercomponents are subjectto wear, damage, and

deterioration, which could expose moving parts or allow

objects to be thrown. Frequently check components and

replace with manufacturer's recommended parts, when nec-

essary.

° Mower bladesaresharpand can cut.Wrap theblade(s)or

wear gloves,and use extracautionwhen servicingthem.

•Check brake operationfrequently.Adjustand serviceas

required,

1 _ Look for thls symbol to POint out im'

portant safety precautions. It means

CAUTIONII! BECOME ALERT!!! YOUR

SAFETY IS INVOLVED. ...............

I- CAUTION: Always disconnect spark plug

| _ wire and placewlre whereit cannot contact

I_spark plug in order to prevent accidental

|i,m starting when setting up, transporting,

| adjusting or making repairs.

m'H • ' HH,{ II IIHHl{ '1 , II ...........

WARNING A

The engine exhaust from this product con-

tains cliemicals known to the State of Califor-

nia to cause cancer, birth defects, or other

reproductive harm.

........................................ II

CONGRATULATIONS on your purchase of a Sears

Tractor, It has been designed, engineered and manufac-

tured to give you the best possible dependability and

performance.

Should you experience any problem you cannot easity

remedy, please contact your nearest Sears Authorized

Service Center/Departmento We have competent, well-

trained technicians and the proper tools to service or repair

this tractor.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your tractor properlyo

Always observe the "SAFETY RULES".

MODEL

NUMBER 917_258524

SERIAL

NUMBER

DATE OF PURCHASE

THE MODELAND SERIAL NUMBERS WILL BE FOUND

ON A PLATE UNDER THE SEAT.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE°

MAINTENANCE AGREEMENT

ASears Maintenance Agreement is available on this prod_

ucto Contact your nearest Sears store for details.

CUSTOMER RESPONSIBILITIES

=Read and observe the safety rules.

.Followa regularschedule in maintaining,caring forand

using your tractor.

°Follow the instructions under "Customer Responsibili-

ties and Storage" sections of this owner's manual.

WARNING: This tractor is equipped with an internal

combustion engine and should not be used on or near any

unimproved forest-covered, brush-covered or grass-cov-

ered land unless the engine's exhaust systemis equipped

PRODUCT SPECIFICATIONS

HORSEPOWER: 15.5

GASOLINE CAPACITY 1.25 GALLONS

AND TYPE: UNLEADED REGULAR

OIL TYPE (API-SF/SG/SH): SAE 30 (above 32°F)

SAE 5W_30 (below 32°F)

OIL CAPACITY: 3,0 PINTS

SPARK PLUG: CHAMPION RJ19LM

(GAP: .030")

VALVE CLEARANCE: INTAKE: °005" - .007"

EXHAUST: .009" - .011"

GROUND SPEED (MPH): FORWARD:

1st 1.1

2rid 1.5

3rd 2.3

4th 345

5th 4.4

6th 5,7

REVERSE: 1.7

TIRE PRESSURE: FRONT: 14 PSI

REAR: 10 PSi

CHARGING SYSTEM: 3 AMPS BATTERY

5 AMPS HEADLIGHTS

BATTERY: AMP/HR: 25

MINo CCA: 190

CASE SIZE: U1R

BLADE BOLT TORQUE: 30-35 FT. LBS.

witha spark arrester meeting applicable local or state laws

(if any)_ If a spark arrester is used, it should be maintained

in effective working order by the operator.

In the state of California the above is required by law

(Section 4442 of the California Public Resources Code)_

Other states may have similar laws. Federal laws apply on

federal lands. A spark arrester for the muffler is available

through your nearest Sears Authorized Service Center/

Department (See REPAIR PARTS section of this manual).

LIMITED TWO YEAR WARRANTY ON CRAFTSMAN RIDING EQUIPMENT

For two (2) years from the date of purchase,if this Craftsman Riding Equipment is maintained, lubricatedand tuned up according

to the instructionsin the owner's manual, Sears will repairor replace, free of charge, any parts found to be defective in material or

workmanship.

This Warranty does not cover:

•Expendable items which become worn during normal use, such as blades, spark plugs, air cleaners, belts, etc,.

° Tire replacement or repaircaused by puncturesfrom outsideobjects,such as nails, thorns,stumps, or glass,

•Repairs necessary because of operator abuse, negligence, improper storage or accident orthe failure to maintain the

equipment accordingto the Instructions contained in the owner's manual°

,Ridingequipment used for commercialor rental purposes°

LIMITED 90 DAY WARRANTY ON BATTERY

For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in material or

workmanship and ourtesting determinesthe battery will not hold a charge, Sears will replace the battery at no charge°

IN-HOME WARRANTY SERVICE ON YOUR CRAFTSMAN RIDING EQUIPMENT IS AVAILABLE AT NO*CHARGE FOR 30

DAYS FROM THE DATE OF PURCHASE. PLEASE CONTACT YOLIR NEAREST SERVICE CENTER. AFTER 2,0DAYS FROM

THE DATE OF PURCHASE, WARRANTY SERVICE IS AVAILABLE BY TAKING YOUR CRAFTSMAN RIDING EQUIPMEkFI" TO

YOUR NEAREST SEARS SERVICE CENTER. (IN-HOME WARRANTY SERVICE WILL STILL BE AVAILABLE AFTER 30 DAYS

FROM THE DATE OF PURCHASE BUT ASTANDARD TRIP CHARGE WILL APPLY.) THIS WARRANTY APPLIES ONLY

WHILE THIS PRODUCT IS IN THE UNITED STATES..

This Warranty gives you specific legal rights, and you may also have other rightswhich may vary from state to state_

SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, IL 60179

iii ii iiiiii .....................................

3

TABLE OF CONTENTS

SAFETY RULES ............................................................ 2

PRODUCT SPECIFICATIONS ...................................... 3

CUSTOMER RESPONSIBILITIES ..................... 3, 15-19

WARRANTY .................................................................. 3

TABLE OF CONTENTS ................................................ 4

INDEX ............................................................................ 4

TRACTOR ACCESSORIES .......................................... 5

ASSEMBLY ................................................................ 7-9

OPERATION ........................................................... 10-14

MAINTENANCE SCHEDULE ...................................... 15

SERVICE AND ADJUSTMENTS ............................ 20-25

STORAGE ................................................................... 26

TROUBLESHOOTING ............................................ 27-28

REPAIR PARTS -TRACTOR ................................. 30-47

REPAIR PARTS- ENGINE .................................... 48-53

PARTS ORDERING/SERVICE .................. BACK PAGE

INDEX

A

Accessories ..................................................5

Adjustments:

Brake ....................................................22

Carburetor .......................................25

Mower:.

Front-To-Back ..............................2t

Side-To-Side .................................21

Throttle Control Cable ....................24

Air Filter, Engine .........................................t8

Air Screen, Engtne ....................................18

Assembly ......................................................7-9

B

Battery:

Charging .........................................7-8

Cleaning .......................................... 17

Connecting .................................. 7-8

Starting with Weak Battery ...........23

Storage .............................................26

Terminals ....................................... 17

Belts:

Motion Drive

Removal/Replacement ........... 22

Mower Blade Drive

Removal/Replacement ..............22

Blade:

Sharpening .........................................16

Replacement ................................ 16

Brake Adjustment .....................................22

C

Carburetor Adjustment ..........................25

Controls, Tractor ................................. 1t

Customer Responsibilities ................15-19

Engine:

Air Filter ..................................... 18

Alr Screen, Engine .................. 18

Battery ........................................ 17

Cooling Fins, Engine ............... 18

Engine Oll ....................................17

Fuel Filter ....................................19

Spark Plugs................................19

Tractor:.

Blades ..............................................16

Lubrication Chart ....................... i5

Maintenance Schedule ........... 15

Tire Care ........................... 8,16,23

Cutting Height, Mower ........................ 12

E

Electrical:

Interlocks and Relays .....................24

Schematic .......................................29

Wiring Diagram ..............................30

Engine:

Air Filter............................................18

Air Screen ........................................18

Cooling Fins, Engine ......................18

Oil Change .................................... 17

Oil Level .......................................t3,17

Oil Type ...........................................17

Preparation .........................................t3

Repair Parts ................................48-53

Starting.............................................14

Storage .......................................... 26

F

Filters:

Air ........................................................18

Fuel ................................................. 19

Fuel:

Type ..................................................13

Storage ............................................26

Fuse ....................................................... 24

G

Gauge Wheels ........................................ 8

H

Hood Remova!iInstallation .................. 24

L

Leveling Mower Deck .......................... 21

LubricationChart ................................ 15

M

Maintenance Schedule ........................ 15

Mower:

Adjustment, Front-to-Back .......... 21

Adjustment, Side-to-Side ................21

Blade Sharpening ....................... 16

Blade Replacement ...................... 16

Cutting Height .............................. 12

Installation .......................................20

Operation ...................................... 13

Removal ...........................................20

Mowing Tips ............................................14

Muffler .................................................. 19

Spark Attester ........................... 3,40

Mulcher Plate ...............................................9

4

O

Oil:

Cold Weather Conditions .........13,17

Engine ..............................................17

Storage ......................................... 26

Operation ..............................................11-14

Operating Mower ................................. 13

Options:

Accessories ..........................................5

Spark Arrester ............................ 3,40

P

Parking Brake .................................. 11-12

Parts Bag ................................................ 6

Parts, Replacement/Repair ........... 30-47

Product Specifications............................ 3

R

Repair Parts .................................... 30-47

S

Safety Rules .......................................... 2

Seat ...................................................... 8

Service and Adjustments .............. 20-25

Brake ............................................. 22

Carburetor ..................................... 25

Fuse .............................................. 24

Hood Removal/Installation .......... 24

Motion Drive Belt

RemovaL/Replacement .............22

Mower Blade Drive Belt

Removal/Replacement ........... 22

Mower Adjustment:

Front-to-Back .......................... 21

Side-to-Side ............................ 2t

Mower fnstaflatlon ........................ 20

Mower Removal .......................... 20

Tire Care ............................. 8,16,23

Slope Guide Sheet .............................. 55

Spark Ptugs........................................... 19

Specifications ........................................ 3

Starting the Engine ........................ 13-14

Steering Wheel ................................. 7,23

Stopping the Tractor ........................... 12

Storage ................................................... 26

T

Throttle Control Cable Adjustment ..... 24

Tires ............................................ 8,16,23

Trouble Shooting Chart ...................27-28

Transaxle Repair Parts .................. 46-47

W

Warranty .................................................. 3

Wiring Diagram ..................................... 30

Widng Schematic ....................................29

ACCESSORI A ATTACHMENTS

These accessories and attachments were available throughmost Sears retailoutletsandservice centers when thetractorwas purchased.

Most Sears stores can order these itemsfor you when you providethe model number of your tractor°

ENGINE

SPARKPLUG GAS CAN ENGINEOIL

MAINTENANCE

BLADES BELTS

PERFORMANCE

Sears offers awide variety of attachments that fit your tractor. Many ofthese are listed below with brief explanations of how they can help

your This list was current at the time of publication;however, itmay change in future years - more attachments may be added, changes

may be made in these attachments, orsome may no longer be available or fit your model. Contact your nearest Sears store for the

accessories and attachments that are available for your tractor.

Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy

attaching and detaching,

AERATOR promotes deep root growth for a healthy lawn,, Ta-

pered 2,5-inch steel spikes mounted on 10-inch diameter discs

puncture holes in soil at close intervals to let moisture soak in.

Steel weight tray for increased penetration.

BAGGER lets you collect grass clippings and leaves for a

healthier, nearer looking lawn_ Two Permanex containers hold

30-gallon plastic bags°

BUMPER protects front end of tractor from damage,

CARTS make hauling easy° Variety of sizes available, plus

accessories such as side panel kits, tool caddy, cart cover,

protective mat and dolly,,

CORING AERATOR takes small plugs out of soil to allow mois-

ture and nutrients to reach grass roots, 36-inch swath_ 24

hardened steel coring tips. 150 lb.,capacity weight tray,

EASY OIL DRAIN VALVE makes oil changes easier, faster,,

FRONT NOSE ROLLER canters infront of mower deck to reduce

chances of "scalping" on uneven terrain.

GANG HITCH lets you tow 2 or3 pull-behind attachments at once,

such as sweepers, dethatchers, aerators (not for use with rollers,

carts or other heavy attachments)°

GAUGE WHEELS on both sldes of the mower deck reduce

chances of "scalping" on uneven terrain. For mower decks not so

equipped.

MULCH RAKE/DETHATCHER loosenssoil and flips thatchand

matted leaves to lawn surface for easypickup_Twenty springline

teeth. Useful to prepare bare areas forseeding, Available for front

or rear mounting. HIGH PERFORMANCE REEL-ACTION

SPRING TINE DETHATCHER covers 36-inch wide path and

tosses thatch into large hopper_ Mounts behind tractor.

MULCHING CLOSE-OUT PLATE KIT, once installed, letsyou

mulch, discharge or bag clippings (bagger optional) without

changing blades. For models not equipped as 3-1n-1Convertible

mowers, See "MOWER" in the Repair Parts section of this

manual.

RAMP TOPS AND FEET let you load and unload tractor from a

pickup truck. Use with 2 x 8 or 2 x 10 lumber_

ROLLER for smoother lawn surface. 36-Inch wide, 18-tnch

diameterwater-tight drum holds up to390 Ibs. of weight. Rounded

edges prevent harm to tuff. Adjustable scraper automatically

cleans drum.

SNOW BLADE forsnow removal only. 14-inch high, 48-inch wide

blade clears42-inchpathwhen angled leftorright, Raises, lowers

withsidelever° Adjustable skids; replaceable, reversible scraper

bar. (Use withtire chains and wheet welghts and/or rear drawbar

weight.)

SNOWTHROWER has40-inch swath. Drum-type auger handles

powdery and wet/heavy snow. Mounts easily with simple pin

arrangement, Discharge chute adjusts from tractor seat, 6*inch

diameter spout discharges snow 10 to 50 feet. Lift controlled at

tractor seat. (Use with chains and wheel weights and/or rear

drawbar weight.)

SPRAYERS use 12-volt DC electric motor that connects to the

tractor battery or other 12.volt soumeo Includes booms for

automaticsprayingand hand held wand for spot sl_raying. Wand

has adjustable spray pattemo For applying herbicides, insecti-

cides, fungicides and liquid fertilizers.

SPREADER/SEEDERS make seeding, fertilizing, and weed kill-

ing easy. Broadcast spreaders are also useful for granular de-

icers and sand.

SWEEPERS let you collect grass clippings and leaves,

TILLER has 5 hpengineand 36-inch swath toprepare seed beds,

cultivate and compost garden residue, Tiller has its own bullFln

liftand depth controlsystem anddoes NOT requirea sleeve hitch,

Fitsany lawn, yardorgarden tractor. Simplyhookup tothe tractor

drawbar and gol Optional accessories convert unit for

dethatching, aerating, htlllng_oowithouttools,

TIRE CHAINS are heavy duty; closely spaced extra-large cross

links give smooth ride, outstanding traction°

TRACTOR CAB has heavy duty vinyl fabric over tubular steel

frame, ABS plastictop;clear plastic windshield offers 360 degree

visibility° Hinged metal doors with catch. Keeps operator warm

and dry. Remove vinyl sides and windshields for use as sun

protector in summer_ Optional accessories include: tinted/

tempered solidsafety glass windshield with hand operated wiper;

12_volt amber caution lightfor mounting on cab top.

VACS for powerfulcollectionof heavy grassclippingsand leaves,

Optional wand attachment to pick up debris in hard-to-reach

places. VACtCHIPPER includes a chipper-shredder.

WEIGHT BRACKET for drawbar for snow removal applications.

Uses (1) 55 Ib,,weight°

WHEEL WEIGHTS for rear wheels provide needed traction for

snow removal or dozing heavy materials,,

5

CONTENTS OF PACK

...................................... i,illllllll i , ii ,111

Parts Bag contents shown full size

(1) Locknut

5/16-18

(1) Hex Bolt 5/16-18 x 1-1/4

iii1,11111111 I" I i , I i II i1,1111'11,1'1'1'1 .......... L::

(1) Shoulder Bolt 5/16-18

1) Lock Washer

1/2

(1) Hex Bolt

1/2-13 x1O

(1) Washer

17/32 x 1-3/16

x 12 Gauge

_Jl_lillltlliillll|qlf (2) Lock Washers #t0

-/'_-_, (2) Washers j'_

(O)3116x314xt6Gauge _ I

_,%1,.__,,./ (2) Weld Nuts #10

...... ........@

(2) Hex Bolts 1/4-20 x 3/4 (2) Hex Nuts 1/4-20

(2) Washers

9/32 x 5/8 x 16 Gauge _.

(2) Lock Washers 1/4

Parts packed separately in carton

III I1'1'1'111111111 iljllll iiiiii, iii '1' II II _ ....

Seat Mulcher

Plate

Steedng

Wheel

Video

Cassette

I

•,,,,

Parts Bag 1

I

iiiiiiii I1'11'1' Illll IHll[ "111'1111111111 ,i,i III LlJlJ'IIII III

Parts bag contents not shown full size

I J[I I I 1/11 IIIUILI JJlJ/lllll '1111111111111

(2) Washers 3t8

x 7/8 x 14 Gauge

(2) Shoulder'

Bolts (2) Gauge @ (2) Center-

Wheels lock Nuts

0

Steering

Extension

Shaft

Steering Wheel

Adapter

Steering

Boot

Steering

(2) Keys Wheel

Insert

Slope Sheet

I1' iii

Assemblys

6

ASSEMBLY

Your new tractor has been assembled at the factory with exceptionof those parts left unassembled for shipping purposes,

To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness°

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier° Standard

wrench sizes are listed.

(1) 3/4" Socket w/drive rachet

(2) 7/'16" wrenches Phillips Screwdriver

(2) 1/2" wrench Tire pressure gauge

(1) 9/16" wrench Utilibj knife

When right or left hand is mentioned in this manual, it

means when you are in the operating position (seated

behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons

from carton (See page 6).

= Cut, from top to bottom, along lines on all four corners

of carton, and lay panels flaL

• Check for any additional loose parts or cartons and

remove.

BEFORE ROLLUNG TRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

°Slide extension shaft onto lower steering shaft. Align

mounting holes in extension and lower shafts and

install5/16 hex bolt and locknuL Tighten securely°

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO

t8-22 FT. LBS TORQUE,

° Place tabs of steering boot over tab slots indash and

push down to secure°

INSTALL STEERING WHEEL

•Positionfront wheels of the tractorso they are pointing

straight forward.

•Slide steeringwheel adapter ontosteering shaft exten-

slono

•Position steering wheel so cross bars are horizontal

(left to right) andslide inside boot and onto adapter.

° Assemble large flat washer, 3/8 lock washer, 3/8 hex

bolt and tighten securely.

°Snap steering wheel insert into center of steering

wheel.

°Remove protective materials from tractor hood and

grill.

IMPORTANT: CHECK FORAND REMOVE ANY STAPLES

INSKID THAT MAY PUNCTURE TIRES WHERE TRACTOR

IS TO ROLL OFF SKIDo

TO ROLL TRACTOR OFF SKID (See Fig. 8)

, Raise attachment lift lever to its highest positionr

° Release parking brake by depressing clutch!brake

pedal°

°Place gearshift lever in neutral (N) position_

° Roll tractor backwards off skid°

°Remove banding holding discharge guard up against

tractor.

WHEEL STEERING

BOOT

ADAPTER

..I EXTENSION SHAFT

5/16 HEX BOLT

5/16 LOCKNUT "_ /._'_ _-_ _..

I

I!

STEERING "_ _._., \ /_/

SHAFT _1 _I_i r_/

FIG. 1

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Figs. 2 and 3)

I I I I I III I iii1,11'1'1IIIUIL_L i

CAUTION: Do not short battery termi-

nals by allowing a wrench or any other

object to contact both terminals at the

same time. Before connecting battery,

remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected

first to prevent sparking from acciden-

tal grounding.

° Remove carboard packing from seat pan and liftseat

pan to raised position.

° Open battery box door.

° Be sure battery drain tube is attached to battery box_

° Remove terminal protective caps and discard_

7

_jl,/llljllll ii iii i,, ,ll, ii illll 1,1,1,11 ,i ii iiilllllll i ........

ASSEMBLY

i iill ii

•If this battery is put into service after month and year

indicated on label (label located between terminals)

charge battery for minimum of one hour at 6-10 amps.

• Firstconnect RED battery cableto positive(+) temfinal

with hex bolt,flat washer, lockwasher and hex nut as

shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) termi-

nal with remaining hex bolt, flat washer, lock washer

and hex nut. Tighten securely.

• Close battery box door.

Open battery box door for:

•Inspection for secure connections (to tighten hard-

ware).

•Inspectionfor corrosion,

•Testing battery.

• Jumping (if required)_

° Periodic charging

,_oTDISCARD TERMINAL

ECTIVE CAPS

NEX LOCK

NUT WASHER

!FLAT

!WASHER

!HEX

BOL_r

SEAT

PAN

BATTERY

BOX DOOR

POSITIVE NEGATIVE

(RED) CABLE (BLACK) CABLE

FIG, 2

8

FIG. 3

INSTALL SEAT (See Fig. 4)

Adjust seat before tightening adjustment bolto

• Remove cardboard packing on seat pan_

•Place seat on seat pan and assemble shoulder bolt.

•Assemble adjustment bolt,{ockwasherandfiatwasher

loosely. Do not tighten.

° Tighten shoulder bolt securely,,

° Lower seat into operating position and sit on seat.

° Slide seat until a comfortable position is reached which

allows you to press clutch/brake pedal all the way

down.

•Get off seat without moving its adjusted position_

° Raise seat and tighten adjustment bolt securely_

iii i Ill I I,I, lllllL lull,H,I

SEAT PAN _ _- Y'_, tl {

ME,T=' _ LOCKWAS.E.

FIG. 4

CHECK TIRE PRESSURE

The tireson your tractor'wereoverinflated at the factoryfor

shipping purposes. Correct tire pressure is important for

best cutting performance.

• Reduce tire pressure to PSI shown in "PRODUCT

SPECIFICATIONS on page 3 of this manual,

CHECK DECK LEVELNESS

For best cuttingresults, mower housing should be properly

leveled. See "TO LEVEL MOWER HOUSING in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL

See the figures that are shown for replacing motion and

mower blade drive belts in the Service and Adjustments

section of this manual Verify that the belts are routed

correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see

that the brake is properly adjusted. See "TO ADJUST

BRAKE" in the Service and Adjustments section of this

manual.

ASSEMBLE GAUGE WHEELS TO MOWER

DECK (See Fig. 5)

The gauge wheels are designed to keep the mower deck in

proper position when operating mower, Be sure they are

properly adjusted to ensure optimum mower performance,

• Adjust mower to desired cutting height (See "TO AD-

JUST MOWER CUTTING HEIGHT' in the Operation

section of this manual)°

° With mower in desired height of cut position, gauge

wheels should be assembled so they are slightly off the

ground. Instatt gauge wheel in appropriate hole with

shoulder bolt, 3/8' washer and 3/8-16 Iocknut and

tighten securely.

° _Repeat for opposite side installing gauge wheel in

same adjustment hole.

GAUGE WHEEL

MOUNTING

BRACKET

\

3/8-16

LOCKNUT

3/8" WASHER

GAUGE WHEEL'

ASS

SHOULDER BOLT

BLY

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place.

Your mower is now ready for discharging or installation of

optional grass catcher accessory°

FIG. 5

INSTALL MULCHER PLATE

(See Figs. 6 & 7)

.Install two latch hooks to mulcher plate using screw,

washer, lock washer, and weld nut as shown,,

NOTE: Pre-assemble weld nut to latch hook by inserting

weld nut from the top with hook pointingdown.

•Tighten hardware securely.

=Raise and hold deflector shield in upright position_

.Place front of mulcher plate over front of mower deck

opening and slide into place, as shown_

=Hook front latch into hole on front of mower deck°

°Hook rear latch into hole on back of mower deck.

CAUTION: Do not remove discharge

guard from mower. Raise and hold

guard when attaching mulcher plate

and allow it to rest on plate while in

operation.

i ,11,,i....................

WELD NUT FROM THE TOP HOOK POINTS DOWN

LOCK

WELD WASHER

NUT_\ SCREW

LATCH

WASHER

MULCHER

PLATE

LOCK

WASHER

WASHER

'_'_SCREW

LATCH

HOOK

WELD

NUT

DEFLECTOR

LATCH

HOOKS

FIG. 7

•/ CHECKLIST

BEFORE YOU OPERATE AND ENJOY YOUR NEW

TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE

THEBESTPERFORMANCEAND SATISFA CTION FROM

THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

,/ A!l assembly instructions have been completed.

,/ No remaining loose parts in carton.

/Battery is properly prepared and charged. (Minimum

1 hour at 6 amps).

,/ Seat is adjusted comfortably and tightened securely.

J All tires are propedy inflated. (For shipping purposes,

the tires were overinflated at the factory).

,/ Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be

properly inflated for leveling)_

,/ Check mower and drive belts. Be surethey are routed

properly around pulleys and inside all belt keepers.

/Check widng_ See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOWTO USE YOUR TRACTOR, PAY

EXTRA ATTENTION TO THE FOLLOWING IMPORTANT

ITEMS:

,/ Engine oil is at proper level.

#" Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

,/ Become familiar with all controls - their location and

function. Operate them before you start the engine.

#' Be sure brake system is in safe operating condition.

FIG. 6 9

.................................................................. • ....................... , LI" I

OPERATION

................................. , ,,,,H ,H,HH, ..................................

These symbols may appear on your tractor or inliterature supplied withthe product. Learn and understand their meaning_

t

A

BATTERY CAUTION OR

WARNING

ENGINE ON ENGINE OFF

REVERSE FORWARD FAST SLOW

OIL PRESSURE CLUTCH LIGHTS ON LIGHTS OFF

I

FUEL CHOKE MOWER HEIGHT DIFFERENTIAL PARKING BRAKE UNLOCKED

LOCK LOCKED

!

MOWER LIFT

REVERSE

NHLc®:>

NEUTRAL HIGH LOW PARKING BRAKE

ATTACHMENT

CLUTCH ENGAGED

ATTACHMENT

CLUTCH DISENGAGED

IGNITION

DANGER, KEEP HANDS AND FEET AWAY

HYDROSTATIC FREE WHEEL

(Hydro Models only)

10

OPERATION

i...................... ::::1,1,, ,

KNOW YOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Comparethe illustrationswithyourtractortofamiliarize yourselfwiththe locationsofvariouscontroisandadjustments_Save

this manual for future reference°

ATTACHMENT IGNITION

CLUTCH LEVER SWITCH

AMMETER

%

THROTTLE/CHOKE

CONTROL

LIGHT SWITCH

POSITION

LIFT LEVER

PLUNGER

CLUTCH/BRAKE

PEDAL

HEIGHT

ADJUSTMENT

KNOB

©ATTACHMENT

LIFT LEVER

PARKING BRAKE

GEARSHIFT

LEVER

FIG. 8

Our tractorsconform to the safety standards of the American National Standards ]nstitute_

ATTACHMENT CLUTCH LEVER: Used to engage the

mower blades, or other attachments mounted to your

tractor°

LIGHT SWITCH: Turns the headlights on and off,

THROTTLE/CHOKE CONTROL: Used for starting and

controllingengine speed.

CLUTCH/BRAKE PEDAL: Used for declutching and brak-

ingthe tractor and starting the engine.

PARKING BRAKE: Locks clutch/brake pedal into the

brake position.

GEARSHIFT LEVER: Selects the speed and direction of

tractor,

ATTACHMENT LIFT LEVER: Used to raise and lower the

mower deck or other attachments mountedto yourtractor,

LIFT LEVER PLUNGER: Used to release attachment lift

lever when changing its position°

IGNITION SWITCH: Used for starting and stopping the

engine.

HEIGHTADJUSTMENT KNOB: Usedto adjustthe mower

cutting height.

AMMETER: Indicates battery charging (÷) or discharging

(-).

'11

ill ..................... i i ill IUUlll ......................................

OPERATION

....... i .................................................. [111111111 IIIIII [

The operation of any tractor can result in foreign objects thrown into the eyes, which can

result insevere eye damage. Always wear safety glasses or eye shields while operating your

tractor or performing any adjustments or repairs. We recommend a wide vision safety mask

over the spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 9)

Your tractor is equipped with an operatorpresence sensing

switch, When engine is running, any attempt by the

operator' to leave the seat without first setting the parking

brake will shut off the engine_

•Depress clutch/brake pedal into full "BRAKE" position

and hold,

Place parking brake lever in"ENGAGED" position and

releasepressurefrom clutctvbrakepedal. Pedalshould

remain in"BRAKE" position. Make sure parkingbrake

will hold tractor secure.

ATTACHMENT CLUTCH LEVER

THROTTLE/ "ENGAGED" POSITION

CHOKE /, ,,

r_n_T=nl _ /'DISENGAGED

'ENGAGED

-I V/

',-\\\ /GEARS.,

_GED"

/.osmoN

CLUTC. .AKEPEDAL

"DRIVE"POSmON HEIG.TADJUSTMENTKNOB

FIG. 9

STOPPING (See Fig. 9)

MOWER BLADES -

• Move attachment clutch lever to "DISENGAGED" po-

sition.

GROUND DRIVE -

°Depress clutch/brakepedal intofuII"BRAKE" position.

•Move gearshift lever to neutral (N) position.

ENGINE -

=Move throttlecontrol to slow position.

NOTE: Failure to move throttlecontrolto slowpositionand

allowing engine to idle before stopping may cause engine

to "backfire"°

°Turn ignition key to "OFF" position and remove key,

Always remove key when leaving tractor to prevent

unauthorized use.

° Never use choke to stop engine.

NOTE: Under certain conditionswhen tractor is standing

idlewiththe enginerunning,hot engine exhaust gases may

cause "browning" of grass. To eliminate this possibility,

always stop enginewhen stopping tractor'on grass areas.

'"'__II L CAUTION: Always stop tractor €0m-

•pletely, as describedabove, beforeleav-

aing the operator s position; to empty

grass catcher, etc. . .

TO USE THROTTLE CONTROL (See Fig. 9)

Always operate engine at full throttle.

• Operating engine at less than full throttle reduces the

battery charging rate.

°Fullthrottleoffersthe best bagging and mower perfor-

mance,

TO MOVE FORWARD AND BACKWARD

(See Fig. 9)

The directionand speed of movement is controlled by the

gearshift Ievero

° Start tractor' with clutch/brake pedal depressed and

gearshift lever in neutral (N) position.

° Move gearshift and range shift levers to desired posi-

tion_,

,Slowly release clutch/brake pedal to start movemenL

IMPORTANT: BRING TRACTOR TO A COMPLETE STOP

BEFORE SHIFTING OR CHANGING GEARS. FAILURE

TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR

TRANSAXLE_

TO ADJUST MOWER CUTTING HEIGHT

(See Fig. 9)

The cuttingheight is controlledby turningthe height adjust-

ment knob in desired direction,

•Turn knob clockwise (fN) to raise cutting height.

•Turn knob counterclockwise (_)to lower cutting

height,

The cuttingheightrange is approximately t-1/2" to 4". The

heightsare measured from the groundto the blade tipwith

the engine not running. These heights are approximate

and may vary depending upon soil conditions, height of

grass and types of grass being mowed.

•The average lawnshould be cutto approximately 2-i t2

inches during the cool season and to over 3 inches

during hot months. For healthier and better looking

lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in

height should be mowed twice. Make the first cut

relativelyhigh; the second to desired height.

12

OPERAON

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sens-

ing switch° Any attempt by the operator to leave the seat

with the engine running and the attachment clutch engaged

will shut off the engine°

.Select desired height of cut.

.Lower mower with attachment lift control,

•Start mower blades by engaging attachment clutch

control°

•TO STOP MOWER BLADES _disengage attachment

clutch control°

!_I_ ..............CAUTION: DO not operatethe mower .......!

A • without either the entire grass catcher, I

on mowers So equipped, or the dis- |

charge guard in place _............................. I

ATTACHMENT CLUTCH LEVER

"DISENGAGED" POSITION "ENGAGED"

POSITION ATTACHMENT

LEVER

HIGH POSI_ON

POSITION

FIG. 10

DISCHARGE

GUARD

TO OPERATE ON HILLS

CAUTION: Do not drive up or down

hills with slopes greater than 15°and

do not drive across any slope.

•Choose the slowest speed before starting up or down

hills.

•Avoid stopping or changing speed on hitls_

°If slowing is necessary, move throttlecontrol lever to

slower position.

o If stopping is absolutely necessary, push clutch/brake

pedal quickly to brake position and engage parking

brake_

•Move gearshift lever to 1st gear. Be sure you have

allowed room for tractor to roll slightly as you restart

movemenL

°To restart movement, slowly release parking brake and

clutchforake pedal

° Make all turns slowly°

TO TRANSPORT

°Raise attachment liftto highest position with attach-

ment lift control°

° When pushingor towing your tractor, be sure gearshift

lever is in neutral (N) position°

°Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting

your tractor on a truck ora trailer, be sure hood is closed and

secured to tractoro Usean appropriate meansoftying hood

to tractor (rope, cord, etc.)o

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 16)

• The engine tnyour tractor has been shipped, from the

factor..,, already filled with summer weight oil.

°Check engine oil with tractor on level ground.

•Remove oil fillcap/dipstick and wipe clean, reinsert the

dipstick and screw cap tight, wait for a few seconds,

remove and read oil level [f necessary, add oil until

"FULL" mark on dipstick is reached. Do not overfill.

° For cold weather operation you should change oil for

easier starting (See "OiL VISCOSITY CHART" in the

Customer Responsibilities section of this manual).

°To change engine oil, see the Customer Responsibili-

ties section in this manual.

13

ADD GASOLINE

°Fill fuel tank. Use fresh, clean, regular unleaded

gasoline with a minimum of 87 octane° (Use of leaded

gasoline will increase carbon and lead oxide deposits

and reduce valve life). Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30

days to assure fuel freshness°

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW 32=F(0°C), USE FRESH, CLEAN WINTER GRADE

GASOLINE TO HELP INSURE GOOD COLD WEATHER

STARTING_

WARNING: Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or methanol) can

attract moisture which leadsto separation and formation of

acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before stor-

age of 30 days or longer. Drain the gas tank, start the

engine and let it run until the fuel lines and carburetor are

empty. Use fresh fuel next season_ See Storage Instruc-

tions for additional information. Never use engine or

carburetor cleaner products in the fuel tank or permanent

damage may occur.

i&CAUTION: Fill to bottom of gas tank

filler neck. Do not overfill. Wipe off any

spilled oil or fuel. Do not store, spill or

use gasoline near an open flame.

........................ iiiiiiiiiiiiiiiiiiii LL LII II II[IIIIIIIIIII

OPERATION

i m,,,,,,,,,,,,,,,,,, iii tNI :"....................... ' '"'"' ............. NNI

TO START ENGINE (See Fig, 9)

When starting the engine for the firsttime or if the engine

has runout of fuel, it will take extra cranking time to move

fuel from the tank to the engine,

•Sit on seat in operating position, depress clutch/brake

pedal and set parking brake.

.Place gear shift lever in neutral (N) position.

•Move attachment" clutch to "DISENGAGED" position.

•Move throttle control to choke position.

Note: Before starting, read the warm and cold starting

procedures below.

•lnsert keyinto ignition and rum keyclockwise to"START"

position and release key as soon as engine starts. Do

not run starter continuously for more than fifteen sec-

onds per minute° if the engine does not start after

several attempts, move throttle control to fast position,

wait afew minutes and try again. If engine still does not

start, move the throttle control back to the choke

position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, movethe throttle control to the fast

position.

.The attachments and ground drive can now be used. if

the engine does not accept the load, restart the engine

and allow itto warm up for one minute using the cf}oke

as described above.

COLD WEATHER STARTING ( 50° F and below)

• When engine starts, allow engine to runwith thethrottle

control in the choke position until the en_lne runs

rougtfly, then move throttle control to fast position. This

may require an engine warm-up period from several

seconds to several minutes, depending on the tem-

perature.

•The attachments can also be used dudng the engine

warm-up period°

NOTE: if at a high altitude (above 3000 feet) or in cold

temperatures (below 32 F) the carburetor fuel mixture may

need to be adjusted for best engine performance. See "TO

ADJUST CARBURETOR" in the Service and Adjustments

section of this manual+

•Do not mow grass when it is wet. Wet grass will plug

mower and leave urldesirableclumps, Allow grass to

dry before mowing.

•Always operate engine at full throttle when mowing to

assure better mowing performance and proper dis-

charge of material. Regulate ground speed by select-

ing a low enough gear to give the mower cutting

performance as welt as the quality of cut desired.

•When operating attachments, select a ground speed

that will suit the terrain and give best performance of

the attachment being used.

MOWINGTIPS

.Tire chains cannot be used when the mower housing is

attached to tractor.

.Mower should be properly leveled for best mow!,n.,g

performance, See 'TO I.EVELMOWER HOUSING in

the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim-

ming.

° Ddve so that clippings are discharged onto the area

that has been cut. Have the cut area to the right of the

tractor. This will result in a more even distribution of

clippings and more uniform cutting.

•When mowin_ large areas, start by tuming to the right

so that clipplngs will discnarge away from shrubs,

fences, driveways, etc. After one or'two rounds, mow

in the opposite direction making left hand turns until

finished (See Fig, 11 ).

•If grass is extremely tall, it should be mowed twice to

reduce load and possible fire hazard from dried clip-

pings. Make first cut relatively high; the second to the

desired heighL

[

1

t

IL

.... ",- "JJ

FIG. 11

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP

MOWER HOUSING FREE OF BUILT-UP GRASS AND

TRASH+ CLEAN AFTER EACH USE.

•The special mulching blade will recut the grass clip-

pingsmany times and reduce them in size so that as

they fall onto the lawn they will disperse into the grass

and not be noticed. Also, the mulched grass will

biodegrade quickly to provide nutrients for the lawn.

Always mulch with your highest engine (blade) speed

as this will provide the best recurring action of the

blades+

•Avoid cutting your lawn when itiswet. Wet grass tends

to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon.

At this time the grass has dried arid the newly cut area

will riot be exposed to the direct sun+

° For best results, adjust the mower cutting height so that

the mower cuts offonly the top one-third of the grass

blades (See Fig. 12). For extremely heavy mulching,

reduce your width of cut and mow slowly+

•Certain types of grass and grass conditions may re-

quire that an area be mulched a second time to com+

pletely hide the clippings. Wt_en doing a second cut,

mow across or perpendicular to the first cut path.

• Change your cutting pattern from week to week. Mow

north to south one week then change to east to west the

next week. This will help prevent matting and graining

of the lawn.

MAX1/3

14 FIG. 12

CUSTOM ESPO LES

MAINTENANCE SCHEDULE .,f___ _._o__

FILL IN DATES /_X_'_._<p_"_. _'_07

AS YOU COMPLETE /_-_,_/_O_

REGULAR SERV!CE /_/_'_ERVICE DATES

Check Brake Operation _/ _/

= , .... ,,_

Check Tire Pressure _ $/

TCheck_er"Le'ose'Fasteners t_/ _, V' ..................................

X

C .............

TCheek Ba}},e,ry 'Leve!/Recharge .....

0Clean Battery and Terminals Q## _/

RCheck Transaxle Cooling _'

.....A ju tB deBeit(s)Tens o" ......... KS' , ,

Adjust Motion Drive Belt(e) Tension _#'s

Check Engine Oil Level _/ _#'

Change Engine OIl _,,3

EClean Air Filter _/'2

NClean Air Screen _ _f2 i : .

GJInspect MuffledSparkArrester

Replace Oil Filter(if equipped)

Clean Engine Cooling Fins

Replace Spark Plug

....... _ | _ i i ! i ;: ; ; ........ ;.........................

Replace Air Filter Paper Cartridge _V#'2

,,,, .................................. , ,,, ,, ,

Replace Fuet Filter

t - Change mote often when operatingunder a heavy toad or in high ambient temperatures

2-Sen/Ice more often when operatingin dirty or dusty conditions,

3_If equipped wiih oil filter,change of!every 50 hours.

4-Repbce blades more often when mowing In sandy soil,,

5 - tf equipped wi_hadjustable system,

6 - Net required Ifequipped with maintenance-free battery.

7-Tighten front axle pivotbolt to 35 ft.*lbs m_lxlmum_

Do not ovedJghten.

GENERAL RECOMMENDATIONS

The warranty on thistractor does notcoveritems that have

been subjected to operator abuse or negligence,_ To

receive fullvalue from the warranty, operator must maintain

tractor as instructed inthis manual

Some adjustments will need to be made periodically to

properly maintain your tractor.

All adjustments in the Service and Adjustments section of

this manual should be checked at least once each season.

Once a year you should replace the spark plug, clean

or replace air filter, and check blades and belts for

wear° A new spark plug and clean air filter assure

proper air-fue! mixture and help your engine run better

and last longer.

LUBRICATION CHART

(_SPINDLE ZERK--_ .__F_---SPINDLE ZERK (_)

(_) FRONT WHEEl;, "=;'_:;'_ FRONT WHEEL (_)

BEARING ZERK _ _ I _ BEARING ZERK

|

®

@CLUTCH

PIVOT(S)

BEFORE EACH USE

oCheck engine oil level

• Check brake operation,

•Check tire pressure.

•Check for loose fasteners..

O

PIVOTS

15

(_ SAE 30 OR 10W30 MOTOR OIL

®GENERAL PURPOSE GREASE

SECTION®REFER TO CUSTOMER RESPONSIBILITIES ENGINE

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS

WHICH HAVE SPECIAL NYLON BEARINGS° VISCOUS LUBRI*

CANTS WILL ATTRACT DUST AND DiRT THAT WILL SHORTEN

THE LiFE OF THE SELF-LUBRICATING BEARINGS. IF YOU

FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW-

DERED GRAPHITE TYPE LUBRICANT SPARINGLY,,

............................. ,,,,,,,,, ,,,, ......................... ill llllll,lUUll iiiill i,iiiiilll,i

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performingany mainte_

nance,

BRAKE OPERATION

if tractor requires more than six (6) feet stopping distance

at high speed inhighest gear, then brake must be adjusted°

(See "TO ADJUST BRAKE" in the Service and Adjust-

ments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See =PROD-

UCT SPECIFICATIONS" on page 3 of this manuaf)o

• Keep tiresfree of gasoline, oil,or insectcontrolchemi-

cals which can harm rubber.

° Avoid stumps, stones, deep ruts, sharp objects and

other hazards that may cause tire damage.

NOTE; To seal tire punctures and prevent flat tiresdue to

slow leaks, tire sealant may be purchased from your local

parts dealer_ Tire sealant also prevents tire dryrot and

corrosion.

BLADE CARE

For best results mower blades must be kept sharp° Re-

place bent or damaged blades.

BLADE REMOVAL (See Fig. 13)

• Raise mower to highest positionto allow access to

blades,

° Remove hex bolt, iockwasherandflatwashersecudng

blade,

° Install new or resharpened blade with trailing edge up

towards deck as shown,

°Reassemble hex bolt, lock washer and flat washer in

exact order as shown°

oTighten bolt securely (30-35 Ft. Lbs. torque),

IMPORTANT: BLADE BOLT IS GRADE 8 HEATTREATED.

NOTE: We do not recommend sharpening blade- but ifyou

do, be sure the blade is balanced.

BLADE

FLAT __\

LOCK WASHER

HEX BOLT

MANDREL,

TRAIUNG EDGE

*A GRADE 8HEAT TREATED BOLT CAN BE

IDENTIRED BY SIX LINES ON THE BOLT HEAD.

FIG. 13

TO SHARPEN BLADE (See Fig. 14)

Care should be taken to keep the blade balanced. An

unbalancedblade willcause excessive vibrationand even-

tual damage to mower and engine.

°The blade can be sharpened with a file or ona gdnding

wheel Do not attempt to sharpen while on the mower.

° To check blade balance, you will need a5/8" diameter

steel bolt,pin,oracone balancer. (When usingacone

balancer, follow the instructions supplied with bal-

ancer)..

- Slide blade on to an unthreaded portion of the steel bolt

or pin and hold the bolt or pin parallel with the ground.

If blade is balanced, it should remain in a horizontal

position. If either end of the blade moves downward,

sharpen the heavy end until the blade is balanced,

NOTE: Do not use a nail for balancing blade. The lobes of

the center hole may appear to be centered, but are not.

CENTER HOLE / /

FIG. 14

16

BATTERY

Your tractor has a battery charging system which is suffi-

cient for normal use, However, periodic charging of the

battery with an automotive charger will extend its life.

• Keep battery and terminals clean_

•Keep battery bolts tight.

o Keep small vent holes open,

• Recharge at 6o10 amperes for I hour°

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause

the battery to "leak" power_

- Open battery box door.

oDisconnect BLACK battery cable first then RED bat-

tery cable and remove battery from tractor.

° Rinse the battery with plain water and dry°

.Clean terminals and battery cable ends with wire brush

until bright°

• Coat terminals with grease or petroleum jelly.

° Reinstall battery (See "CONNECT BATTERY" in the

Assembly section of this manual)oV-BELTS

Check V-belts for deterioration and wear after 100 hours of

operation and replace if necessary. The belts are not

adjustabTeoReplace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which

can restrict cooling,

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)

improve starting in cold weather, these multi-viscosity oils

wilt result in increased oil consumption when used above

32°F. Check your engine oil level more frequently to avoid

possible engine damage from running low on clio

Change the oil after every 25 hours of operation or at least

once a year ifthe tractor isnot used for25 hours inone year°

Check the crankcase oil level before starting the engine

and after each eight (8) hours of operation. Tighten oil fill

cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs° 15 and 16)

Determine temperature range expected before oil change,

All oil must meet API service classification SF, SG or SH.

° Be sure tractor is on level surface.

°Oil will drain more freely when warm.

• Catch oil in a suitable container.

= Remove oil fill cap/dipstick, Be careful not to allow dirt

to enter the engine when changing oil,

= Remove drain plug.

°After oil has drained completely, replace oil drain plug

and tighten securely.

° Refill engine with oil through oil fill dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see

"PRODUCT SPECIFICATIONS" on page 3 of this

manual.

° Use gauge on oil fill cap/dipstick for checking level° Be

sure dipstick cap is t=ghtenedsecurely for accurate

reading. Keep oil at "FULL" line on dipstick.

ENGINE

LUBRICATION

Only use high quality detergent oil rated withAPI service

classification SF, SG or SH. Select the oil's SAE viscosity

grade according to your expected operating temperature.

SAE VISCOSITY GRADES

°F .SO" o° '........3o°_" 40°.........._o eo• Ioo.

i°c -3oo -20_...........-loo, oo Ioo 2o° 3o° 40•

i!EMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

FIG. 15

FILL

CAP/DIPSTICK

OIL DRAIN

PLUG

FIG. 16

17

CUSTOMER

= Ill J lu=lllll=llllu=ll=L=,

AIR FILTER (See Fig. 17)

Your engine will not run properly using a dirty air filter,

Clean the foam pre-cleaner after every 25 hoursof opera-

tion or every season, Service paper cartridge every 100

hours of operationor every season, whichever occurs first,

Service air cleaner more often under'dustyconditions.

• Remove knob(s) and cover.

TO SERVICE PRE-CLEANER

°Slide foam pre-cleaner off cartridge°

° Wash it in liquiddetergent and water,

• Squeeze it dry in a clean cloth°

• Saturate it in engine oil, Wrap it in clean, absorbent

cloth and squeeze to remove excess oil,

•if very dirty or'damaged, replace pre-cleaner.

° Reinstall pre-cleaner over cartridge°

•Reinstall cover and secure with knob(s)..

TO SERVICE CARTRIDGE

° Remove cartridge nut.

° Carefully remove cartridge to prevent debris from en-

tering carburetor. Clean base carefully to prevent

debris from entering carburetor.

° Cleancartridgebytappinggentlyonflatsurface. if very

dirty or damaged, replace cartndgeo

•Reinstall cartridge, nut, precleaner, cover and secure

with knob(s).

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS

KEROSENE, ARE NOT TO BE USED TO CLEAN THE

CARTRIDGE, THEY MAY CAUSE DETERIORATION OF

THE CARTRIDGE. DO NOT OIL CARTRIDGE° DO NOT

USE PRESSURIZED AIR TO CLEAN OR DRY

CARTRIDGE

COVER KNOB

COVER CARTRIDGE NUT

PAPER

CARTRIDGE

IBILITIES

CLEAN AIR SCREEN (See Fig. 18)

Air screen must be kept free of dirt and chaff to prevent

engine damage from overheating, Clean withawire brush

or compressed air'to remove dirt and stubborn dried gum

fibers,

ENGINE COOLING FINS (See Fig. 18)

Remove any dust, dirt or oil from engine cooling fins to

prevent engine damage from overheating,

. Remove screws from blower housing and lift housing

and dipsticktube assembly off engine,

°Cover oil fill opening to prevent entry of dirt.

•Use compressed air or stiff bristle brushto thoroughly

clean engine cooling fins_

•To reassemble, reverse above procedure.

SCREWS BLOWER

HOUSING

DIPSTICK

TUBE

ASSEMBLY

PLUG

ENGINE COOLING FINS

FIG. 18

FIG. 17

18

CUSTO ESPONSH LmTUES

i i I pl ,Ulll i _, iiiiii I iiI i LLILiii iI ....: : ,_,

MUFFLER

Inspect and replace corroded muffler and sparkarrester (if

equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing

season or after every 100 hours of operation, whichever

occurs first. Spark plug type and gap setting are shown in

"PRODUCT SPECIFICATIONS" on page 3 of this manual,

IN-LINE FUEL FILTER (See Fig. 19)

The fuel filter should be replaced once each season,, If fue!

filter becomes clogged, obstructingfuel flow to carburetor,

replacement is required.

° With engine cool, remove filter and plug fuel line

sections°

oPlace new fuel filter in position in fuel line with arrow

pointing towards carburetor.

° Be sure there are no fuel tine leaks and clamps are

properly positioned.

° Immediately wipe up any spilled gasoline.

CLAMP CLAMP

FUEL

FILTER

CLEANING

FIG. 19

•Clean engine, battery, seat, finish, etc, of all foreign

matter.

°Keep finished surfaces and wheels free of all gasoline,

oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose to clean your

tractor unless the electrical system, muffler, air filter and

carburetor are covered to keep water ouL Water in engine

can result in a shortened engine life.

19

.... ii ii ii ,,llUl,ii

SERVICE AND ADJUSTM

........................... ii i, i,i ii iiiiiiiilU ............ I!/IIIIIIIII[IlUI[ , iiii , i iiiii

O

I

CAUTION" BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS;

Depress clutch/brake pedal fully and set parking brake,

Place gearshift lever in neutral (N) position.

Place attachment clutch in "DISENGAGED" position.

°Turn ignition key "OFF" and remove key.

°Make sure the blades and all moving parts have completely stopped.

°Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with

plug,

.............. .......................... Illl

TRACTOR

TO REMOVE MOWER (See Fig. 20)

Mower willbe easierto remove from the rightsideof tractor.

•Place attachment clutch in "DISENGAGED" position.

°Move attachment liftlever forward to lowermowerto its

lowest position.

°Roll belt off engine pulley°

° Disconnect clutch rod from clutch lever by removing

retainer spring.

° Disconnect anti-sway bar from chassis bracket by

removing retainer spdng.

°Disconnect suspension arms from rear deck brackets

by removing retainer springs.

°Disconnect front links from deck by removing retainer

springs.

° Raise lift lever to raise suspension arms° Slide mower

out from under tractor:

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE

MOWER IS TO BE MOUNTED TO THE TRACTOR, THE

R.H. AND L.H. SUSPENSION ARMS MUST BE REMOVED

FROM TRACTOR.

TO INSTALL MOWER (See Fig. 20)

o Raise attachment lift lever to its highest positiono

° Slide mower under tractor with discharge guard to right

side of tractor.

° Lower lift lever to its lowest position°

° install mower in reverse order of removal instructions°

CLUTCH

RETAINER

SPRING

ANTI-SWAY BAR RETAINER

SPRINGS

(BOTHSIOES)

FIG. 20

RETAINER

SPRANG

20

RVmCE AND

-- :: ,,iH,=l=,,,,tiH====......... lll,i ..............................

TO LEVEL MOWER HOUSING

Adjust the mower while tractoris parked on level ground or

driveway. Make sure tires are properly inflated (See

"PRODUCT SPECIFICATIONS" onpage 3 of this manual).

If tires are over or underinflated, you will notproperly adjust

your mower°

SIDE-TO-SIDE ADJUSTMENT (See Figs. 21 and 22)

= Raise mower to its highest position.

° At the midpoint of both sides of mower, measure height

from bottom edge of mower to ground. Distance"A"on

both sides of mower should be the same or within I/4

of each other.

ADJUSTMENTS

,,it,_..... llll

FRONT-TO*BACK ADJUSTMENT (See Figs° 23 and 24)

IMPORTANT; DECK MUST BE LEVEL SIDE-TO-SIDEo IF

THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS

NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS

EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-

SIDE.

To obtain the best cutting results, the mower housing

should be adjusted so that the front is approximately 1/8" to

1/2" lower than the rear when the mower is in its highest

position.

Check adjustment on right side of tractor, Measure dis-

tance"D" directly in front and behind the mandrel at bottom

edge of mower housing as shown.

° If adjustment is necessary, make adjustment on one

side of mower only.

= To raise one side of mower, tighten lift link adjustment

nut on that side.

oTo lower one side of mower, loosen liftlink adjustment

nut on that side.

NOTE: Each full turn of adjustment nut willchange mower

height about 1/8".

o Recheck measurements after adjusting.

BOTTOM EDGE BOTTOM EDGE

OF MOWER TO OF MOWER TO

GROUND GROUND

GROUND LINE A

FIG. 21

°Before making any necessary adjustments, checkthat

both front links are equal in length. Both linksshould be

approximately 10-3/8".

• If links are not equal in length, adjust one link to same

length as other link.

°To lower front of mower loosen nut "E" on both front

links an equal number of turns.

= When distance "D" is 1/8" to 1/2" lower at front than

rear, tighten nuts "F" against trunnion on both front

links.

• To raise front of mower, loosen nut"F" from trunnion on

both front links. Tighten nut "E" on both front links an

equal number of turns.

°When distance "D" is 1/8" to 1/2" lower at front than

rear, tighten nut"F" against trunnion on both front links,

° Recheck side-to-side adjustment.

MANDREL

LIFT LINK

ADJUSTMENT NUT

FIG. 22

21

FIG. 23

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT

NUT "E"

FRONT LINKS TRUNNION

FIG. 24

SERVICE AND ADJUSTM

WITHPARKINGBRAKE "ENGAGED"

TO REPLACE MOWER BLADE DRIVE BELT

(See Fig. 25)

The mower blade drive belt may be replaced withouttools.

Park the tractor on level surface. Engage parking brake°

BELT REMOVAL -

*Remove mower from tractor (See "TO REMOVE

MOWER" in this section of this manual).

,Work belt off both mandrel pulleys and idler pulleys,

° Pull belt away from mower',

BELT INSTALLATION -

• Install new bett in reverse order of removal.

*Make sure belt isin all pulley grooves and insideall belt

guides°

•Install mower in reverse order of removal instructions,

MANDREL IDLER

PULLEY PULLEYS

MANDREL

PULLEY

FIG. 25

TO ADJUST BRAKE (See Fig. 26)

Your tractor is equipped with an adjustable brake system

which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance

at high speed in highestgear, then brake mustbe adjusted,

•Depressclutch/brake pedaland engage parkingbrake,

* Measure distance between brake operating arm and

nut 'W' on brake rod.

Ifdistance is otherthan 1-1/2", loosen jam nut and turn

nut "A" until distance becomes 1-112'L Retighten jam

nut against nut "A",

Road test tractor for proper stopping distance as stated

above° Readjust if necessary. If stopping distance is

still greater than six (6) feet in highest gear', further

maintenance is necessary° Contact your nearest au-

thorized service center]department.

NUT "A"

JAM NUT

OPERATING ARM

22

FIG, 26

TO REPLACE MOTION DRIVE BELT

(See Fig. 27)

Park the tractor on level surface. Engage parking brake,

For assistance, there is abelt installation guide decal on

bottom side of left footrest.

•Remove mower (See "TO REMOVE MOWER" in this

section of this manual.)

• Remove upper belt keeper°

•Remove belt from stationary idler and clutching idler,

• Pull belt slack toward rear' of tractor° Remove belt

upwards from transaxle pulley by deflecting belt keep-

ers,

•Pull belt toward front oftractor and remove downwards

from around engine pulley.

• Install new belt by reversing above procedure,

IMPORTANT; MAKE SURE UPPER BELT KEEPER IS

POSITIONED PROPERLY BETWEEN LOCATOR TABS,

r

/ PULLEY JI-LoOATOR

! CLUTCH_NG--...L---'-_._p-'f il TASS

|il j{( o),_ | Ir_ UPPER BELT

/STATIONARY_ ""_'1 I l! KEEPER

/ I! II !!

/TRANSAXLE_ II _ !!

FIG. 27

SERVICE A D

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (leftto right)

when wheels are positioned straight forward, remove steer-

ing wheel and reassemble per instructionsin the Assembly

section of this manual.

FRONT WHEEL TOE-INICAMBER

The front wheel toe-in and camber are not adjustable on

your tractor, tf damage has occurred to affect the front

wheel toe-in or camber, contact your nearest authorized

service center/department,,

TO REMOVE WHEEL FOR REPAIRS

(See Fig, 28)

.Block up axle securely_

=Remove axle cover, retainingringandwasherstoallow

wheel removal (rear wheel containsa square key - Do

ADJUSTMENTS

TO START ENGINE WITH A WEAK BATTERY

(See Fig. 29)

t

,_ CAUTION: Lead-acid batteries gener-

_-]_ ateexplosive gases. Keep sparks, flame I

and smoking materials away from bat- |

_1_ teries. Always wear eye protection |

when around batteries.

If your battery is too weak to start the engine, it should be

recharged. If "jumper cables" are used for emergency

starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A12

VOLT NEGATIVE GROUNDED SYSTEM, THE OTHER

VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE

GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR

BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

not lose).

= Repair tire and reassemble.

= On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

° Replace washers and snap retaining ring securely in

axle groove.

° Replace axle cover,_

NOTE: To seal tire punctures and prevent flat tires due to

slow leaks, tire sealant may be purchased from your local

parts dealer° Tire sealant also prevents tire dry' rot and

corrosion.

°Connect each end of the RED cable to the POSITIVE

(+) terminal of each battery, taking care not to short

against chassis.

° Connect one end of the BLACK cable to the NEGA-

TIVE (-) terminal of fully charged battery°

°Connect the other end of the BLACK cable to good

CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

° BLACK cable first from chassis and then from the fully

charged battery_

• RED cable last from both battedeso

WASHERS

RETAINING

RING

AXLE COVER

I

"_ SQUARE KEY

(REAR WHEEL ONLY)

FIG. 28

POSITIVE TERMINAL

POSITIVE TERMINAL

NEGATIVE TERMINAL

CABLES

CHARGED

BATTERY

NEGATIVE TERMINAL

FIG. 29

23

SERVICE AND ADJUSTM

TO REPLACE HEADLIGHT BULB

e

e

Q

Raise hood.

Pull bulb holder out of the hole in the backside of the

grill°

Replace bulb in holder and push bulb holder securely

back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run

poorly, stop running, or prevent it from starting.

°Check wiring. See electrical wiring diagram in the

Repair Parts section of this manual.,

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The

fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

(See Fig. 30)

•Raise hood,

•Unsnap headlight wire connector.

•Standinfront of tractor, Grasp hoodatsides, tilttoward

engine and lift off of tractor.

•To replace, reverse above procedures.

HOOD

HEADLIGHT

WIRE

CONNECTOR

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

(See Fig. 31)

The throttle control has been preset at the factory and

adjustment should not be necessary. Check adjustment as

described below before loosening cable. If adjustment is

necessary, proceed as follows:

.With engine not running, move throttle control lever

from slow to choke position. Slowly move lever from

choke to fast position.

° Check that holes"A" in governor control lever and hole

in governor plate line-up. If holes "A" are not aligned,

loosen clamp screw and move throttle cable until holes

are aligned. Tighten clamp screw securely,

GOVERNOR GOVERNOR

CONTROL LEVER CONTROL PLATE

\

HOLES "A" CLAMP THROTTLE

SCREW CABLE

FIG. 31

FIG. 30

24

TO ADJUST CARBURETOR (See Fig. 32)

The carburetor has been preset at the factory and adjust-

merit should not be necessary. However, minor adjust-

ment may be required to compensate for differences infuel,

temperature, altitude or Ioado If the carburetor does need

adjustment, proceed as follows:

tn general, turning idle mixture valve in (clockwise) de-

creases the supply of fuel to the engine giving a leaner fuel/

air mixture. Turning the idle mixture valve out (counter-

clockwise) increases the supply of fuel to the engine giving

a richer fuel/air mixture.

IMPORTANT: DAMAGE TO THE NEEDLE VALVE AND

THE SEAT IN CARBURETOR MAY RESULT IF SCREW IS

TURNED IN TOO TIGHT,

PRELIMINARY SETTING -

o Air cleaner assembly must be assembled to the carbu-

retor when making carburetor adjustments.

°Be sure the throttle control cable is adjusted properly

(see above).

° With engine off turn idle mixture valve in (clockwise)

closing it finger tight and then turn out (counterclock-

wise) ! full turn.

FINAL SETTING

°Start engine and allow to warm for five minutes. Make

final adjustments with engine running and shift/motion

control lever in neutral (N) position.

= Move throttle control lever to slow position_With finger,

rotate and hold throttle lever against idle speed screw°

Turn idle speed screw to attain 1750 RPM.

oWhile still holding throttle lever against idle speed

screw, turn idle mixture valve in (clockwise) unttl en-

gine begins to die and then turnout (counterclockwise)

until engine runs rough° Turn valve to a point midway

between those two positions. Release throttle lever.

,ll iiiii ..................

USTMENTS

i'l'l'l'l'H'll'l'L_l'_l II ll"l"l""I....................

ACCELERATION TEST -

° Move throttle control lever from slow to fast position. If

engine hesitates or dies, turn idle mixture valve out

(counterclockwise) 1/8 turn° Repeat test and continue

to adjust, if necessary, until engine accelerates

smoothly_

High speed stop is factory adjusted. Do not adjust -

damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND

EXPERIENCE TO MAKE ANY NECESSARY

ADJUSTMENTS°

THROTTLE IDLE SPEED

LEVER SCREW'

IDLE MIXTURE

VALVE

FIG. 32

25

Immediately prepare your tractor for storage at the end of

the season or if the tractor will not be used for 30 days or

more.

'lqll :::::: : /'11!

A CAUTION: Never storethe tractor with

!• • gasoline in the tank inside a building

!_where fumes may reach an open flame

!_or spark. Allow the engine to cool

I before storing in any enclosure,

TRACTOR

Remove mower from tractor for winter storage. When

mower' is to be stored for a period of time, clean it thor-

oughly, remove all dirt, grease, leaves, etc. Store in a

clean, dry area°

• Clean entiretractor (See"CLEANING"in the Customer

Responsibilities section of this manual).

•Inspect and replace belts, if necessary (See belt re-

placement instructions in the Service and Adjustments

section of this manual).

• Lubricate as shown in the Customer Responsibilities

section of this manual.

•Be sure that all nuts, bolts and screws are securely

fastened. Inspect moving parts for damage, breakage

and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

BATTERY

• Fully charge the battery for storage_

•After a period of time in storage, battery may require

recharging°

• To help prevent corrosion arid power leakage during

long periods of storage, battery cables should be

disconnected and battery cleaned thoroughly (see _O

CLEAN BATTERY AND TERMINALS in the Cus-

tomer Responsibilities section of this manual).

• After cleaning, leave cables disconnected and place

cables where they cannot come in contact with battery

terminals,

•Be sure battery drain tube is securely attached_

• if battery is removed from tractor for storage, do not

store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM

DEPOSITS FROM FORMING tN ESSENTIAL FUEL

SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER,

FUEL HOSE, OR TANK DURING STORAGE. ALSO,

EXPERIENCE INDICATES THAT ALCOHOL BLENDED

FUELS (CALLED GASOHOL OR USING ETHANOL OR

METHANOL) CAN ATTRACT MOISTURE WHICH LEADS

TO SEPARATION AND FORMATION OF ACIDS DURING

STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL

SYSTEM OF AN ENGINE WHILE IN STORAGE.

*Drain the fuel tank_

• Start the engine and let it run until the fuel lines and

carburetor are empty.

•Never use engine or carburetorcIeaner products inthe

fuel tank or permanent damage may occur.

•Use fresh fuel next season_

NOTE: Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits dudng stor-

age. Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stabilizer

container'. Run engine at least 10 minutes after adding

stabilizer to allow the stabilizer to reach the carburetor. Do

not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drainoil (withengine,warm) and replace with clean engine

oil. (See "ENGINE' in the Customer Responsibilities

section of this manual).

CYLINDERS

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into

cylinder(s).

•Turn ignitionkey to"START" positionfor afew seconds

to distributeoil.

•Replace with new spark plug(s)=

OTHER

•Do not storegasoline from one season to another.

•Replace your gasoline can tf your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to

give protection from dust arid dirt.

•Cover your tractor with a suitable protective cover that

does not retain molsture_ Do not use plastic. Plastic

cannot breathe which allows condensation to form and

will cause your' tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE

AND EXHAUST AREAS ARE STILL WARM.

26

PROBLEM

Wtll not start

Hard to start

Engine wig not turn over

,llllll,i, i,ll t,i

Engine clicks but wtll not

start

Loss of power

Excessive vibration

CAUSE

1,, Out of fuel,,

2,, Engine not =CHOKED" prope.dy,

3 Engine f|ooded_

4_ Bad spark plug,

5o Dirty air filter,,

6o Dirty fuel filter

7, Water in fuai_

8_ Loose or damaged wiring,

9. Carburetor out of adjustment.

10,, Engine valves out of adjustment.

1o Dirty air filter,

2. Bad spark plug,,

3,. Weak ordead battery,

4o Dirty fuel filial

5, Stale or dirty fuel.

6_ Loose or damaged wiring°

7o Carburetor out of adjustment,

8, Engine valves out of adjustment,

1, Clutch/brake pedal notdepressed.,

2. Attachment clutch is engaged,,

3,, Weak or dead battery_

4,, Blown fuse°

5_ Corroded battery terminals.,

6, Loose or damaged widng

7. Faulty ignitionswitch.

8. Fau{ty solenoid or stader.

9 Faulty operator presence switch(es),

1.. Weak or dead battery,

2, Corroded battery terminals,

3, Loose or damaged wiring.

4, Faulty solenoid or starter.

1_ Cutting too much grass/too fast,

2. Throttle tn "CHOKE" position.

3o Build-up of grass, leaves and trash under mower,

4,, Dirty air filter.

5_ Low oil levelldfrty oil

6. Faulty spark plug.

7,, Dirty fuel filter,.

8. Stale or dirty fuel,

9 Water infuel.

10, Spark plug wire loose,

11 Dirty engine air screen/fins,

12,, Dirty/clogged muffler,

13. Loose or damaged wiring,

14, Carburetor out of adjustment°

15, Engine valves out of adjustment,

1,, Worn, bent orloose blade_

2_ Bent blade mandrel

3, Looseldamaged part(s),

CORRECTION

1,, Fill fuel tank,

2. See "TO START ENGINE" in Operation section,

3, Wait several minutes before attempting to start,

4, Replace spark plug,

5,, Clean/replace air filter,

6. Replace fuel filter.

7, Drain fuel tank and carburetor, refill tank with fresh

gasoline and replace fuel filter.,

8, Check all wiring.

9See "To Adjust Carburetor" in Service Adjustments

section.

10, Contact an authorized service center/department.

1o Clean/replace afr rifler,

2, Replace spark p{ug,

3,, Recharge or replace battery,,

4, Replace fuel filter,

5_ Drain fue) tank and refill with fresh gasolineo

6, Check all wiring.

7, See "To Adjust Carburetor" in Service Adjustments

section,

8, Contact an authorized service centar/department_

1,, Depress clutclVbrake pedal

2, Disengage attachment dutch

3,, Recharge or replace battery°

4. Replace fuse_

5. Clean battery terminals,

6, Check all wiring,

7. Checldreplace ignition switch

8, Check/replace solenoid or starter

9_ Contact an authorized service center/depadment_

1Rechargeor replacebattery_

2. Cleanbatteryterminals,

3, Checkallwiring

4_ Check/replacesolenoidor starter°

I, Set in =Higher Cut" pos_fion/reduce speed°

2. Adjust throttle control

3. Clean underside of mower housing.

4 Clean/replace air filter,

5. Check oHlevel/change oil,

6, Clean and regap or change spark plug.

7. Replace fuel filter

8. Drain fuel tank and refill with fresh gasoline.

9- Drain fuel tank and carburetor, refill tank with fresh

gasoline and reprace fuai filter,

10_ Connect and tighten spark plug wire.

tl. Clean engfne air screen/fins

12. Clean/replace muffler.

13 Check all wiring.

14. See "To Adjust Carburetor" tn Service Adjustments

section,

15, Contact an authorized service centerfdepartmenL

1 Replace blade_ Tighten blade boll

2_ Replace blade mandrel.

3 Tighten loose part(s) Replace damaged pads°

27

TROU HOOTING POINTS

PROBLEM

Engine continues to run

when operator leaves seat

with attachment clutch

engaged

Poorcut-uneven

Mowerblades will not

rotate

Poor grass discharge

Headlight(s) not working

(if so equipped)

Battery will not charge

Engine "backfires"

when turning engine

"OFF"

CAUSE

: .................

1. Faulty operator-safety presence control system.

1, Worn, bent or loose blade.

2. Mower deck not level.

3. Buildup of grass, leaves, and trash under mower,

4. Bent blade mandrel,

5_ Clogged mower dock vent holes from buUdup of

grass, loaves, and trash around mandrelsv

1o Obstructiontnclutchmechanism

2_ Wor!!damagedmowerdrive belt.

3_ Frozenidlerpulley,

4. Frozenblade mandrel,

t, Enginespeed toos{ow.

2o Travelspeedtoofast.

3, Wet grass°

4. Mowerdecknotlevel

5. Low/uneventireairpressure,

6. Worn,bent orlooseblade,

7., Buildup ofgrass, leavesand trash under mower.

8, Mowerdrive beltworn,

9, Blades improperlylnstaUed_

I0_ improperblades used.

11. Cloggedmowerdeckventholesfrom buildupof

grass,leaves,and trasharoundmandrels°

1. Switch is"OFF".

2, Bulb(s) burned out.

&Faulty light switch.

4. Loose or damaged wldng,,

5, Blown fuse,.

1,. Bad battery call(s).

2_ Poor cable connections,

3. Faulty regulator (if so equipped).

4. Faulty altemator,

1. Enginethrottlecontrolnot set at "SLOW"

posttlonfor30 secondsbeforestoppingengine,

CORRECTION

..... _IILIIIIIIll i ' iiiilllllll

tCheck wiring, switches and connectlons_ tf not

corrected, contact an authodzsd service center/

departrnent_

1Replace blade. Tighten blade bolt.

2, Level mower deck.

3. Clean underside of mower housing

4. Replace blade mandrel,,

5_ Clean around mandrels to open vent holes

1. Remove obstruction,

2. Replace mower ddve bell

3. Replace Idler pulley..

4. Replace blade mandrel,

1. Place throttle control in "FAST" posttlon_.

2. Shift to slower speed,

&Allow grass to dry before mowing

4. Levet mower deck.

5. Check tires for proper air pressure,

6,_ Replace!sharpen blade. Tighten blade bolt.

7. Clean underside of mower housing,

8 Replace mower drive belt.

9_ Reinstall blades sharp edge down.

I0. Replace with blades listed tn this manual

11. Clean around mandrels to open vent holes,

1. Turn switch "ON".

2, Replace butb(s)

3_ ChecPJreplace light switch_

4. Check wtdng and connections_

5_ Replace fuss,

1o Replace battery,,

2, Check/clean all connecttons_

3, Replace regulator.

4. Replace alternator.

Movethrottlecontrolto =SLOW"postl_onand allow

to Idle for 30 secondsbefore stoppingengine,

28

SCHEMATIC

RED olllllIo

BATTERY

BLACK

AMMETER

(OPTIONAL)

RE_

IGNITION

SWITCH

J

SOLENOID

WHITE

RED

STARTER

BLACK

SEAT SWITCH

(NOT OCCUPIED)

7 .... t-

I I BLACK

9LACK

HOUR _)

F

iw._ I © '

t I

t I

J A_M-E_TdL-U_-6H"_

(CLUTCHOFF) 1

_-_ METER

(OPTIONAL)

BLACK

r t

= FUEL=

i ---/A"k--_NE =

FUELSHUT-OFF

SOLENOID

(_ IGNITION

UNIT

GROUNDING

CONNECTOR

CHARGING SYSTEM OU'_UT

3AMP DC @3600 RPM

...........SPARK

I..__._ PLUG

GAP _ _t

i(2 PLUGSON

TWIN CYL. ENGINES) {

ORANGE

IGNITION SWITCH

PosmoN CIRCUIT "MAKE"

OFF G+M'+L! NONE"'

RUNILIGHT B+L A + Y

RUN ........B + L NONE

START B + L ÷S NONE

NOTE

YOUR TRACTOR IS

EQUIPPED WITH ASPECIAL

ALTERNATOR SYSTEM. BROWN

THE LIGHTS ARE NOT

CONNECTED TO THE

BATTERY, BUT HAVE THEIR

OWN ELECTRICAL SOURCE°

BECAUSE OF THIS, THE

BRIGHTNESS OF THE LIGHTS

WILL CHANGE WITH ENGINE

SPEED. AT IDLE THE LIGHTS

WILL DIM. AS THE ENGINE IS NON-REMOVABLE

SPEEDED UP, THE LIGHTS CONNECTIONS

WILL BECOME THEIR BRIGHTEST_

28 VOLTS AC MiN. Q3800 RPM

(CHARGING SYSTEM DISCONNECTED)

HEADLIGHTS

/-;

REMOVABLE

CONNECTIONS

WIRING INSULATED CLIPS

NOTE: tF WIRING INSULATED CLIPS WERE REMOVED FOR

SERVICING OF UNIT, THEY SHOULD BE REPLACED TO

PROPERLY SECURE YOUR WIRING°

29

REPAIR PARTS

TRACTOR-- MODEL NUMBER 917.258524

ELECTRICAL

2O

33

29

I

i 2°

\|

t

I

I

I

I

I

I

3O

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.258524

ELECTRICAL

KEY PART

NO. NO. DESCRIPTION

1 I44925

2 747604'12

3 STD551025

4 STD551125

6 STD541025

7 109238X

8 156417

9 109596X

16 153664

19 STD551125

2O 73350400

21 147430

22 4t52J

24 4799J

25 146147

26 108824X

28 4207J

29 121305X

30 140301

31 124211X

32 141226

33 109310X

40 156442

4i 71110408

42 I31563

43 145673

44 73640400

45 121433X

52 14194O

7O 140422

Battery I2 Volt 25 Amp

Bolt, Hex Head 1/4-20 unc x 3/4

Washer

Washer

Nut

Tube, Plastic, 12"

Case, Battery Mech Hinge

Clamp, Hose

Switch, Tnterlock Push-In

Washer, Lock

Nut, Hex, Jam 1/4-20 UNC

Harness, Light Socket

(Includes 4152J)

Bulb, Light

Cable, Battery, 6 Gauge, Red, 11"

Cable, Battery, 6 Gauge, Red, W/16

Wire

Fuse, 30 Amp

Cable, Ground, 6 Gauge, Black, t2"

Switch, Plunger

Switch, Ignition

Nut, Ignition

Cover, Key Switch

Key, Ignition

Harness, Ignition

Bolt, Hex Head, Fin. 1/4-20 x 1/2

Cover, Terminal, Red

Solenoid

Nut Keps BIk Hex 1/4-20 UNC

Ammeter Rectangular 6 Amp

Protection Wire Loop

Harness Engine B&S

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

31

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

CHASSIS AND ENCLOSURES

26

12

53

32

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

CHASSIS AND ENCLOSURES

KEY PART

NO. NO. DESCRIPTION

1 159527

2 140356

317490612

4 19131216

5155272

9 150156X01t

10 STD533710

11 155927

12 14566O

13 155936

t4 17490608

17 144983X558

18 126938X

25 19131312

26 STD541437

28 145198X558

29 155217

30 151287X558

31 139976

37 174905O8

38 139886

39 139887

51 73800400

52 19091416

53 145201

54 17030814

55 145202

57 STD522507

60 72140606

64 154798

71 73680400

74 73680600

I14 158112

115 17490620

116 19'131614

122 157301

123 152927

140 '158418

142 156095

143 154966

144 154207

145 156524

147 74760412

-- 5479J

Chassis Assembly

Drawbar

Screw, Thd. Rollo 3/8-16 x 3/4

Washer 13/32 x 3/4 x 16 Gauge

Bumper Hood/Dash

Dash

Bolt, Carriage 3/8-16 x 3/4

Panel, Dash, L.H.

Clip Tinnerman Grille P/L

Panel, Dash, R.H.

Screw Thdrol 3/8-16 x 1/2

Hood Assembly

Bumper Hood

Washer 13/32 x 13/16 x 12 Gauge

Nut

Grille w/Ctips MS-558

Lens, Grille

Fend/Ftrest Pnt STLT N HLD 558

Bracket, Fender Support

Screw Thdrol 5/16-18 x 1/2

Pivot Bracket Assembly, L.H.

Pivot Bracket Assembly, R.H.

Nut Lock w/Insert 1/4-20 UNC

Washer 9/32 x 7/8 x 16 Ga_,

Bracket Grille Pickoff LH

Screw Spidertock Hex Hd #8-7/8

Bracket Grille Pickoff RH

Bolt, Fin Hex 1/4-20 UNC x .75

Bolt Rdhd Sqnk 3/8-16 UNC x 3/4

Dash Lower STLT

Nut Crownlock 1/4-20 UNC

Nut Crownlock 3/8-16 UNC

Keeper Belt Rear LH STL P930

Screw Thdrol 3/8-16 x 1-1/4

Washer 13/32 x 1 x 14 Ga.

Bracket Shift STLT

Screw TT #10-32 x 5 x 3/8 Flange

Bracket Suspension Front

Plate Reinforcement STLT

Bracket Swaybar Chassis

Bracket Pnt Footrest STLT

Rod Pivot Chassis/Hood

Bolt Hex Hd 1/4-20 UNC x 3/4

Plug, Button

NOTE: All component dimensions given in U.So inches

1 inch = 25.4 mm

33

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917,258524

DRIVE

57

31

81

19

75

18

62 35

40,-._

38 ,...._

42 ,..._

39-.....

34

5otl

37

26 27

116

48

150

151

51

34

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917,258524

DRIVE

KEY PART KEY PART

NO. NO. DESCRIPTION NO. NO. DESCRIPTION

t ........ Transaxle (See Breakdown) 53 1057t0X

Peerless 930-057A 55 105709X

2 146682 Spring, Return, Brake 56 STD5237t2

3 123666X Pulley, Transaxle 57 130801

4 12000028 Ring, Retainer 58 127274X

5 121520X Strap, Torque 59 140312

6 17490512 Screw, Thdo, Roll., 5/16-18 x 3/4 61 17490612

8 154792 Rod Shifter Fender STLT 62 8883R

10 STD5612!0 Pin, Cotter 63 140186

11 105701X Washer, Shift Plate 64 71170764

13 74550412 Bolt I/4-28 UNF W/Patch Grade 8

14 STD551125 Washer 65 STD551143

15 74490544 Bolt, Hex Flghd 5/16_I8 Grade 5 66 154778

18 STD523710 Bolt Fin Hex 3/8-16 UNC x 1. Gr 5 70 134683

19 STD541437 Nut 72 19132012

21 106933X Knob 74 137057

22 130804 Rod, Brake 75 121749X

24 STD541237 Nut 76 STD581075

25 106888X Spring, Brake Rod 77 123583X

26 STD551037 Washer 78 121748X

27 STD561210 Pin 79 2228M

28 145204 Rod, Parking Brake 80 145090

29 124236X Cap, Parking Brake, Red 81 156049

30 130807 Bracket, Transaxle 82 123782X

31 127275X Keeper, Belt, Loll. 83 19171216

32 STD523107 Bolt 84 145643

34 155071 Shaft Assembly, Foot Pedal 85 150360

35 120183X Bearing, Nylon 86 7t208

36 STD551082 Washer 87 19212016

37 STD571810 Roll Pin 88 12000008

38 123674X Pulley, IdJer, Flat 89 154886

39 STD523727 Bolt 90 124346X

40 4470J Spacer, Split .395 x.59 96 4497H

41 154777 Keeper, Belt, Idter Fool-Proof 112 19091210

42 19131312 Washer 13/32 x 13/16 x'12 Gauge 113 t27285X

47 127783 Pulley, Idler, V-Groove, Plastic 116 72110610

48 154604 Bellcrank Assembly 118 154774

49 123205X Retainer, Belt 121 154419

50 STD523715 Bolt

51 STD541437 Nut Crown Lock 3/8-16 UNC

52 STD541431 Nut Crown Lock 5!16-18 UNC

Link, Clutch

Spring, Clutch Return

Bolt Fin Hex 3/8-16 x 1-1/4

V-Belt, Ground Drive

Keeper, Belt, R.H°

Keeper, Belt, Center Span

Screw, Thdo, Rotto 3/8-16 x 3/4

Cover, Pedal

Pulley, Engine

Bolt, Hex Head, Fin.

7/16-20 x 4 Grade 5

Washer

Keeper, Belt, Engine, Fool-Proof

Guide, Mower Drive Belt, R_H.

Washer 13/32 x 1-1/4 x 12 Gauge

Spacer, Axle

Washer 25/32 x 1-1/4 x 16 Gauge

E-Ring

Key, Square 2°0 x .1845/.1865

Washer 25/32 x 1-5/8 x 16 Gauge

Key Woodruff #9 3/16 x 3t4

Arm, Shift

Shaft Assembly

Spring, Torsion

Washer 17/32 x 3/4 x 16 Gauge

Tie Rod

Nut, Nylock

Bushing, Pivot

Washer

E-Ring

Console, Shift, STLT

Nut, Self-Threading, Washer Hd 1/4

Retainer Spring 1" Zinc Cad

Washer 9/32 x 3/4 x 10 Gauge

Strap Torque LT

Bolt Rdhd Sqneck 3/8-16 x 1..25

Spacer Bellcrank

Nyliner Clutching STL

NOTE: All component dimensions given in U.S. inches

1 inch = 25°4 mm

35

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

STEERING ASSEMBLY

62

L, '

ft_

27

jr

25

10

28

30

32

43

36

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917,258524

STEERING ASSEMBLY

KEY PART

NO. NO. DESCRIPTION

t i39768

2154427

3 156483

4 157473

5 6266H

6 121748X

7 19272016

8 12000029

9 3366R

10 156438

I1 STD551137

13 154779

15 73901000

17 156546

16 57079

19 124035X

20 126684X

22 71200410

23 127501

25 154406

26 126847X

27 136874

28 19131416

29 17490612

3O STD561210

32 130465

36 155099

37 152927

38 139769

39 191338O8

40 STD541537

41 I00711L

42 145054

43 121749X

44 153720

46 121232X

47 6855M

51 STD541431

53 736806OO

54 74780520

62 156594

63 STD523710

65 'i54760

66 154404

67 74781044

68 154429

69 160367

70 74780636

Steering Wheel

Axle Assembly STMP Dropped STL

Spindle Assembly, LH.

Spindie Assembly, R.H.

Bearing, Race, Thrust, Hardened

Washer 25/32 x 1-5/8 x 16 Gauge

Washer 27/32 x 1_1/4x 16 Gauge

Ring, Klip

Bearing, Steering Column

Draglink Extended Stamped

Washer, Lock

Bearing Axle STLT/GT

Nut, Lock, Flange 5/8-1'1 UNC

Shaft Assembly, Steering

Washer, Thrust .515 x .750 x _033

Support, Shaft

Washer, Shim i/4 x 5/8 x .062

Screw, Hex Socket 1!4-20 x 5/6

Pittman Shaft Assembly

Bracket, Steering

Bushing, Link, Drag

Gear, Sector

Washer 13/32 x 7/8 x 16 Gauge

Screw, Thd., Roll. 3/8-16 x 3/4

Pin

Rod, Tie

Bushing, Steering

Screw

Insert, Steering Wheel

Washer 13/32 x 2-3/8 x 8 Gauge

Gripco Nut

Adaptor, Steering Wheel

Boot, Steering Shaft

Washer 25/32 x 1-1/4 x 16 Gauge

Extension Shaft Steering LR°LT

Cap, Spindle

Fitting, Grease

Nut Lock Hex w/ins. 5/16-18 UNC

Nut, Crownlock 3/8-16 unc

Bolt Fin Hex 5/16-16 UNC x 1-1/4

Kit Steering Asm Service

Bolt, Fin Hex 3/8-16 UNC x 1 Gr 5

Spacer Axle

Bearing Arm Pittman

Bolt, Fin Hex 5/8-I 1 UNC x 2-3/4

Axle, Brace

Spacer, Brace Axle

Bolt, Fin Hex 3/8-16 unc x 2-1/4

NOTE: All component dimensions given in UoS.inches

1 inch = 25.4 mm

37

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917,258524

SEAT ASSEMBLY

10

KEY

NO.

1

2

3

4

5

6

7

8

9

10

12

13

14

PART

NO,

140123

140551

STD523710

19131610

145006

STD541437

124t 8t X

17490616

19131614

155925

121246X

121248X

72050411

KEY PART

DESCRIPTION NO. NO, DESCRIPTION

Seat

Bracket, Pivot, Seat

Bolt

Washer 13/32 x i x 10 Gauge

Clip, Push-In Hinged

Nut

Spring, Seat

Screw, Thd., Roll. 3/8-16 x 1

Washer' 13/32 x I x 14 Gauge

Pan, Seat Emboss QCK Conn.

Bracket, Switch Mounting

Bushing, Snap

Bolt, Carriage 1/4-20 x 1-3/8

15 134300

16 121250X

17 123976X

21 153236

22 STD541431

23 74780814

24 19171912

25 127018X

26 STD551150

Spacer, Split .28 x.88

Spring

Locknut, Flange 1/4 Grade 5

Bolt, Shoulder 5/16-18 UNC

Nut

Bolt, Hex Head, Fin.

1/2-13 x 7/8 Grade 5

Washer 17/32 x 1-3/16 x 12 Gauge

Bolt, Shoulder 5/16-18 x .62

Washer, Lock

NOTE: All component dimensions given in U.S. inches

1inch = 25.4 mm

38

REPAIR PARTS

TRACTOR- -MODEL NUMBER 917.258524

DECALS

9 13 2 6 3 18 7718 4

!10

2O

14

12 13

KEY

NO. PART

NO.

1 156368

2 150333

3151299

4 15130O

6 133644

7 15O927

8 156787

9 146709

10 156439

DESCRIPTION

Decal, Oper. Instr_

Decal Cap Cnsmr Help Line

Decal Hood, R°H.

Decal Hood, L.H.

Decal Customer Maintenance

Decal Side Panel

Decal Deck Mower EZ3

Decal Fender, Craftsman

Decal Fender Danger

WHEELS & TIRES

4,10

11

KEY PART

NO. NO.

12

13

14

'18

20

'146046

147139

136832

151708

149516

138311

154515

154516

160917

160918

DESCRIPTION

Decat, V_Bett Drive Schematic

Decal, Chassis, 6 Speed/42"

Decal, V-Belt Schematic

Decal, Ins. Hood

Decal Battery Dngr/Psn Eng

Decal, Lift Handle

Pad Footrest LH STLT

Pad Footrest RH STLT

Owner's Manual, English

Owner's Manual, Spanish

KEY PART

NO. NO. DESCRIPTION

1 59192

2 65139

3 106222X

4 59904

5 106732X427

6278H

7 9040H

8106108X427

9138468

10 7152J ._

tl 104757X

-- 144334

Valve Cap, Tire

Stem, Valve

Tire, Front

Tube, Front Tire

(Not Provided, Service Item Only)

Rim, Front

Fitting, Grease (Front Wheel Only)

Beating, Flange (Front Wheel Only)

Rim, Rear

Tire, Rear

Tube, Rear Tire

(Not Provided, Service Item Only)

'Cap, Axle

Sealant, Tire 10 oz.

NOTE: All component dimensions given in U.S. inches

: 1 inch = 25.4 mm

39

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.258524

ENGINE

3

81

62 _"

4

78

14

6

38 78

÷-

40 23

29

\

OPTIONAL EQUIPMENT

Spark Arrester

4O

REPAIR PARTS

TRACTOR - -MODEL NUiViBER 917,258524

ENGINE

KEY PART

NO. NO. DESCRIPTION

1

2150600

17720410

4 137352

13 272293

14 13280324

t5 1320O300

16 STD551237

23 156123

29 137180

31 I09202X

32 123549X

33 123487X

35 1749O512

37 137040

38 .......

4O 124028X

44 17490412

46 19091416

62 STD551131

72 71070512

78 1749O620

81 128861

Control, Throttle

Screw, Hex Head, Thread Cutting

1/4-20 x 518

Engine, B&S (See Breakdown)

Model No. 28N707, Type No. 0173-01

Muffler

Gasket, Exhaust

Nipple, Pipe 3/8 NPT x 3

Elbow, Standard 90,3/8-18 NPT

Washer

Shield, Heat

Arrestor, Spark

Tank, Fuel

Cap Assembly, Fuel Tank, Vented

Clamp, Hose

Screw Thdrol 5/16-18 x 3-4 Tyt

Line, Fuel

Plug, Oil Drain

(Order From Engine Manufacturer)

Bushing, Snap, Fuel Line

Screw, Hex Washer Head, Thdo, Roll.

1/4-20 x 3/4

Washer 9/32 x 7/8 x 16 Gauge

Washer, Lock

Screw, Hex Cap Head 5/16-18 x 3/4

Screw, Thd., Roll. 3/8-16 x 1-1/4

Nut Flange 1/4-20 Starter Nut

NOTE: All component dimensions given in U.S inches

1 inch = 25°4 mm

41

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

MOWER LIFT

5 49

13

4

6

12

3O

3

\

26

/

1

65

7

8

19

13

2O

15

42

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917.258524

MOWER LIFT

KEY PART

NO. NO. DESCRIPTION

1 159460

2 159471

3105767X

4 t2000002

5 19211621

6 120183X

7 12563tX

8 122365X

11 139865

12 139866

13 4939M

15 127218

16 73350800

17 130171

18 73800800

19 139868

20 3t46R

23 110807X

24 19'131016

25 2876H

26 76020308

27 126971X

28 7335O600

29 138057

30 150233

31 140302

32 73540600

49 145212

50 110452X

LiftLever Inner Wire Assembly

Shaft Assembly, Lift

Pin, Groove

E-Ring

Washer 21/32 x I x 21 Gauge

Bearing, Nylon

Grip, Handle, Fluted

Button, Plunger, Red

Link, Lift, L.H.

Link, Lift, R.H.

Retainer Spring

Link, Front

Nut, Hex, Jam 1/2-13 UNC

Trunnion

Locknut, Hex, with Washer Insert

1/2-13 UNC

Arm, Suspension, Rear

Retainer Spring

Nut, Special

Washer 13/32 x 5/8 x 16 Gauge

Spring

Pin, Cotter 3/32 x 1/2

Rod, Adjust, Lift

Nut, Hex, Jam 3/8-t6 UNC

Knob, Infinite Height Adjustment

Trunnion, inf Height

Bearing, Pvt, Lift Spherical

Nut, Crownlock 3/8-24

Nut Hex Flange Lock

Nut Push Phos & Oil

NOTE: All component dimensions given in U°S. inches

1 inch = 25.4 mm

43

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917.258524

MOWER DECK

74

76

68

52

58

34

33

31

101

"'_ 104

105"

106

105

106

116 113 111 114 i

117119_-_ 121_;

118...._ I

21

\2

16

18

29

18

113

117

116

27

44

REPAURPARTS

TRACTOR --MODEL NUMBER 917.258524

MOWER DECK

KEY PART KEY PART

NO. NO. DESCRIPTION NO, NO. DESCRIPTION

1 144393 Mower Housing 56 122052X

2 STD533107 Bolt 58 140086

3 138017 Bracket Assembly,Sway Bar, Front 59 141043

4 138440 Bracket Assembly, Sway Bar 67 149846

5 STD624008 Retainer Spdng 68 144200

6 130832 Arm, Suspension, Rear 71 142427

8 850857 Bolt, Hex 3/8-24 x 1.25 Grade 8 72 131870

9 STD55!137 Washer, Lock 73 t27847

10 140296 Washer, Hardened 74 121748X

11 134149 Blade, Mulching 75 12000029

12 t29895 Bearing, Ball 76 128903

13 t37645 Shaft Assembly, Mandrel, Vented 77 127845

(Includes Key Number 6) 78 154809

14 128774 Housing, Mandrel, Vented 79 127498

15 '110485X Bearing, Ball, Mandrel 80 153701

16 140329 Stripper, Vented Mower Deck 81 73350600

17 72110610 Bolt, Carriage 3/8-16x 1-1/4 82 142028

18 72140505 Bolt, Carriage 5/16-18 x 5/8 83 120958X

19 132827 Bolt, Shoulder 84 156084

20 136888 Baffle, Vortex 85 72140618

21 STD54143t Nut Crownlock 5/16-18 UNC 92 STD541437

22 134753 Stiffener Bracket 'i01 136420

23 131267 Bracket, Deflector 102 71161010

24 t05304X Cap, Sleeve 103 19061216

25 123713X Spring, Torsion, Deflector 104 STD551110

26 110452X Nut, Push 105 130758

27 130968 Shield, Deflector 106 2029J

28 19111016 Washer 11/32 x 5/8 x16 Gauge 111 155197

29 131491 Rod, Hinge 112 155198

30 138776 ScrewThdrol Hex Head Zinc Mwr 1'13 17490512

31 129963 Washer, Spacer 114 73510500

32 153535 Pulley, Mandrel 115 72110504

33 137266 Nut, Toplock, Flanged !16 137644

34 STD533717 Bolt 117 133957

35 133835 Fastner, Christmas Tree 118 73930600

36 131494 Pulley, Idler, Flat 119 19121414

37 19131316 Washer 13/32x 13!16x 16 Gauge 121 143723

40 STD541437 Nut Crownlock 3/8-16 UNC 128 153390

41 133551 Rod, Pivot, with Nibs t29 19131312

43 140083 Rod, Clutch, Secondary, with Nibs 130 STD523710

44 140088 Guard, Mandrel, L_H. 131 STD533710

45 STD624003 Retainer 132 19132203

46 137729 Screw, Thd. Roll 1/4-20 x 5/8 - - 130794

48 t33944 Washer, Hardened

49 155066 Roller Assembly, Cam Follower - - 159481

50 131340 Bolt, Shoulder #10-24Grade 5

51 STD541410 Locknut

52 139888 Bolt, Shoulder 5/16-18 UNC

53 131845X900 Arm Assembly, Pad, Brake

54 133943 Washer, Hardened

55 155o46 Arm, Idler

Spacer, Retainer

Spring, Torsion Brakes

Guard, TUV Idler

Knob Custom Oval

V-Belt

Rod, Clutch, Primary, with Nibs

Spring, Return

Arm, Clutch, Secondary

Washer 25/32 x 1-5/8 x 16 Gauge

Ring, Klip

Bolt, Shoulder 3/8-16 UNC x 1.44

Keeper, Spring

Lever Asm. Clutch Pri Plm STLT

Bushing, Large, Brass

Spring, Mower Clutch

Nut, Hex Jam 3/8-16 Unc

Trunnion, Adj.

Washer, Sintered

Keeper Belt Idler

Bolt Carriage 3/8-16 x 2-1/4

Nut

Mulcher Cover

Screw

Washer #10

Washer, Lock

Latch Assembly, Bagger

Nut, Weld

Bracket, Gauge, Wheel L.H.

Bracket, Gauge, Wheel R.Ho

Screw Thdrol 5/16-18 x 3/4

Nut, Hex, Keps 5/16-'18 UNC

Bolt, Carriage 5/16 UNC x 1/2

Bolt, Shoulder

Wheel, Gauge

Nut, Centerlock 3/8-16

Washer 3/8 x7/8 x 14 Gauge

Bracket

Washer Felt

Washer 13/32 x 13/16 x 12 Ga.

Bolt, Fin Hex 3/8-16 UNC x 1 Gr. 5

Bolt, RDHD SQNK 3/8-16 UNC x !

Spacer Washer

Mandrel Assembly (Includes Key

Numbers 8-10, 12-15, 31 and 32)

Mower Deck, Complete (Standard

Deck, Order Separately Mulcher

Plate and Gauge Wheel

Components, Key Nos. 101-106

and 111-121)

NOTE: All component dimensions given in UoS. inches

1 inch = 25.4 mm

45

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

PEERLESS TRANSAXLE -MODEL NUMBER 930-057A

_8 34

/

7

35 9

31

68

5

8

/

23 31 35

/

13

67

77

29

15

69

36

13

79

45

42

52

58 59

65

33

6O

61

23

!

1

!

46

REPAIR PARTS

TRACTOR --MODEL NUMBER 917.258524

PEERLESS TRANSAXLE -MODEL NUMBER 930-057A

REF PART REF PART

NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 772'108A Cover, Transaxle 43 792075

2 780086A Bearing, Needle 44 790025

3 770102A Case, Transaxle 45 786066

4 776260A Shaft, Counter 46 786086

5 776219B Shaft and Pinion Assembly, Output 47 774690

6 778139 Gear, Output, 35 Teeth 48 774691

7 778136 Gear, Spur, 15Teeth, Steel 49 778215

8 792136A Key, Shift 50 778125

8A 792047 Key, Woodruff 51 778124A

9 784352 Collar, Shifter 52 778123A

t0 784355 Rod and Fork Assembly, Shift 53 778122A

tl 778229 Gear, Bevel, 42 Teeth 54 778273

12 778113A Bevel Pinion, Input 56 778230

13 778221 Gear, Bevel, 16 Teeth 57 778151

14 778068 Gear, Bevel Pinion 58 778126A

15 778260 Gear, Ring 59 778127A

17 786139 Pin, Drive 60 778128A

18 786102 Spacer, Neutral 61 778163

20 792077 Ball, Steel 5/16" diameter 65 780109

21 792078 Set Screw 3/8-16 x 3/8 66 776135

22 792079 Spring 67 776315A

23 788061 Ring, Seal 68 786116A

25 792073 Screw, Flanged Hex Head, Thread 69 780051

Forming 1/4-20 x 1-1/4 70 786118

26 792125 Ring, Retainer 71 788069

(4 Required, Package of 2) 72 792165

27 792035 Ring, Retainer 72A 788091

28 788040 Ring, Retainer 76 780090

29 780072 Washer, Thrust 77 788078A

30 780108 Washer, Thrust

31 780001 Washer 79 792144

32 792001 "O" Ring 81 786081

33 788095 Seal, Square Cut

34 780105A Bushing, Flanged 82 786082

35 780118A Bushing, Flanged 83 786123

36 790003 Disk, Brake 90 788067B

37 790007 Plate, Brake Pad 103 792166

38 799021 Pad, Brake (Package of 2) 104 792167

39 786026 Pin, Dowel 150 788093

40 792076A Washer, Flat 900 794602

41 790079 Lever, Brake

42 792073 Screw, Flanged Hex Head, Thread

Forming 1/4-20 x 1-1/4

42A 792085A Screw 1/4-20 x 2-t/4

Locknut 5/16-24

Holder, Brake Pad

Spacer

Bracket, Brake Lever

Axle 11-5/16" long

Axle 16-1/2" long

Gear, Spur, 37 Teeth, Steel (1.)

Gear Spur, 35 Teeth (2-,)

Gear Spur, 30 Teeth (3_)

Gear Spur, 25 Teeth (4_)

Gear S _ur, 22 Teeth (5=)

Gear S _ur, 12 Teeth, Steel

Gear S )ur, 15 Teeth (2..)

Gear S )ur, 20 Teeth (3.)

Gear S _ur, 25 Teeth (4.)

Gear S _ur, 28 Teeth (5.)

Gear S Jur, 31 Teeth (6_)

Washer Thrust

Shaft, Input

Shaft, Brake, 4 Keyed

Plug

Washer, Thrust

Spacer

Square Cut Ring

Plug, Threaded 9/16-18

"O" Ring

Washer, Thrust

Ring, Retaining, Inverted

(Package of 2)

Spring, Brake

Chain, Roller

(Number 41 Chain, 24 Links)

Sprocket, 9 Teeth (Reverse)

Sprocket, 18 Teeth (Reverse)

Grease, Bentonite, 32 Ounce Bottle

Screw 1/4-20 x 2

Locknut 1/4-20

Gasket Eliminator (Loctite #515)

Replacement Transaxle

NOTE: All component dimensions given in UoS.inches

1 inch = 25°4 mm

Parts must be ordered from Tecumseh Products Co.

47

REPAIR PARTS

TRACTOR -- MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE - MODEL NUMBER 28N707, TYPE NUMBER 0173-01

718

230

_614

635 337

562

230 634A

"k REQUIRES SPEClALTOOLS

TO INSTALL. SEE REPAIR

INSTRUCTION MANUAL.

35 @

238(_

4O

868A

166

1029

294 _

1034

1022

1026

45

48

7

52

_13

_P

305

1023

REPAIR PARTS

TRACTOR - -MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE -MODEL NUMBER 28N707, TYPE NUMBER 0173-01

iilllill

127 138 106 987 95 117

137 147

121 CARBURETOR OVERHAUL KIT

634 634B

142

123

_r REQUIRES SPECIALTOOLS

TO INSTALL. SEE REPAIR

INSTRUCTION MANUAL.

130

i1033 VALVE OVERHAUL KIT

46

142

÷22

15

137

13e_

ii

49

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE - MODEL NUMBER 28N707, TYPE NUMBER 0173-01

20 634A 842

3 524 868 868A I

I

i51 \

GASKET SET

1 138

137

9_7'"CARBU.ETORGASKETSET

467

535

445

304

305_p 468

1006

668

1044

7s

224

334

50

REPAIR PARTS

TRACTOR- -MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE -MODEL NUMBER 28N707, TYPE NUMBER 0173-01

877

783

801

311

544

803

1090

51

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE - MODEL NUMBER 28N707, TYPE NUMBER 0173-01

KEY PART KEY PART

NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 496412

2 399265

3391086

5495858

7 272614

8 495735

9 27803

10 94621

1t 281246

12 271916

271997

271996

13 94728

15 94239

16 495162

94196

t8 494238

20 291675

22 94624

23 492326

24

25

26

27

28

29

32

32A

33

34

35

37

40

45

46

51

52

53

75

78

222698

495860

495977

495978

495979

495854

495852

495851

495855

260924

299691

391286

494504

495490

94695

94648

495856

495857

262811

224502

224641

262411

496884

272465

272569

94637

224061

94832

Cylinder Assembly 95

Bearing, Cylinder 98

* Seal, Oil 104

Head, Cylinder 105

*** Gasket, Cylinder Head 106

Breather Assembly 108

* Gasket, Valve Cover 117

Screw, Sems 118

Tube, Breather 12t

* Gasket, Crankcase Cover, o015" 123

* Gasket, Crankcase Cover, _005" 125

* Gasket, Crankcase Cover, _009" 127

Screw, Cylinder Head 130

Plug, Oil Drain 131

Crankshaft 133

Timing Gear Key 137

Base, Engine t38

* Seal, Oil 141

Screw, Sems, Base Mounting 142

Flywheel and Ring Gear Assembly, 147

Magneto 164

Key, Flywheel 166

Piston Assembly, Standard Size 171

Piston Assembly, _010"Oversize 187

Piston Assembly, .020" Oversize 188

Piston Assembly, .030" Oversize 192

Ring Set, Piston, Standard Size 201

Ring Set, Piston, .010" Oversize 209

Ring Set, Piston, .020" Oversize 2t6

ing Set, Piston, ..030" Oversize 219

Lock, Piston Pin 222

Pin Assy. Piston, Standard Size 224

Pin Assyo, Piston, .005" Oversize 225

Rod Assembly, Connecting 227

Rod Assembly, Connecting, 230

.020" Undersize Crankpin Bore 232

Screw, Hex Washer' Head, 1-57/64 238

Screw, Hex Washer Head, 1-5/8 240

Valve, Exhaust 265

Valve, Intake 284

Spring, Valve

Guard, Flywheel

Retainer, Valve Spring

Tappet, Valve

Gear, Cam

**** Gasket, Carburetor (Carburetor to

Elbow) (Also Included in Gasket

Set, Part Number 495993)

*** Gasket, Carburetor

(Elbow to Cylinder')

Stud, Carburetor Mounting

Washer, Spring

Screw, Pan Head

94098

495800

231789

231855

231854

224540

231858

495932

498116

94616

498051

224539

494379

494381

281165

281164

495931

231859

497472

214047

94555

281051

393815

94627

492160

262767

260695

262766

490815

495611

94729

495157

493935

94742

262785

262836

394358

221535

94704

11.*

it*

Screw, Throttle

Screw, Idle Speed

Pin, Float Hinge

Valve Float

Seat, Inlet Valve

Valve, Choke

Jet, Needle Valve

Valve, Needle

Carburetor Overhaul Kit

Screw, Elbow Mounting

Carburetor'Assembly

Plug, Welch (Sold in Kit Only)

Valve, Throttle

Shaft and Lever, Throttle

Float, Carburetor

Gasket, Float Bowl

Washer, Bowl

Shaft and Lever, Choke

No_le, Carburetor'

Pilot,Jet

Elbow, Carburetor

Stud, Rocker Arm

Nut, Air Cleaner Mounting

Line, Fuel (11" Long, Cut to Suit)

Screw, Sems

Screw Assembly, Rocker Arm

Link, Governor

Spring, Governor

Link, Choke

Gear, Governor

Plate, Governor Control

Screw, Sems, Air Cleaner

Crank, Governor

Lever Assembly, Governor'

Washer', Governor Crank

Spring, Governor Link

Cap, Valve

Filter, Fuel (In Fuel Line)

Clamp, Casing

Screw, Hex Head

* Included in Gasket Set (495993)

** Includedin Carburetor Kit (497535)

*** Included in both Gasket Set (495993) and

Valve Overhaul Kit (495992)

**** Included in Gasket Set (495993), Carburetor Kit

(497535) and Carburetor Gasket Set (494385)

NOTE: All component dimensions given in U.S. inches

1inch = 25.4 mm

52

REPAIR PARTS

TRACTOR - - MODEL NUMBER 917.258524

BRIGGS & STRATTON ENGINE - MODEL NUMBER 28N707, TYPE NUMBER 0173-01

KEY PART KEY PART

NO. NO. DESCRIPTION NO, NO. DESCRIPTION

284A 94073 Screw, Hex Head 729A 225170 Retainer, Wire

294 810088 Screw, Set 741 262932 Gear, Timing

304 496280 Housing, Blower 757 213998 Link, Counterweight

305 94786 Screw, Hex, Head, 758 399891 Counterweight Assembly

759 298909 Pin, CounterweightBlower Housing Mounting

306 225020 Shield, Cylinder 761 94593 Screw, Counterweight

307 94386 Screw, Cylinder Shield 783 280104 Gear, Starter

309 497595 Motor, Starter 801 394856 Cap, Drive

310 497602 Bott, Thru 802 497605 Cap, End

311 497608 Bn_sh Set 803 497604 Housing, Starter

333 495859 Armature, Magneto 842 270920 * Seal, Oil Filler Cap

334 93381 Screw, Sems, Armature Mounting 847 496415 Fill Group, Oil

337 491055 Plug, Spark 851 224110 ***Terminal, Ignition Cable

346 93705 Screw, Hex Head 868 494435 Seal Assembly, Valve

356 497708 Wire Assembly 868A 272610 *** Gasket, Valve

358 495993 Gasket Set 87i 262835 Bushing, Guide (Intake & Exhaust)

363 19203 Puller, Flywheel 872 281361 Cover, Air Cleaner

383 89838 Wrench, Spark Plug 875 495862 Body, Air Cleaner

423 94073 Screw, Sems 877 393456 Diode and Connector Assembly

445 493909 Cartridge, Air Cleaner 947 497157 Solenoid

455 222561 Cup, Screen Mounting 965 94010 Nut, Hex

467 493903 Knob, Air Cleaner 975 495933 Bowl Assembly, Carburetor

468 494439 Screen, Flush Rotating 977 494385 Carburetor Gasket Set

474 393474 Stator, Alternator 987 281!66 ** Seal, Throttle Shaft

482 93621 Screw, Sems 1005 281400 Fan, Flywheel

510 497606 Drive, Starter !006 224413 Retainer, Fan

523 495230 Cap and Dipstick, Oil Filler 1019 496758 Label Kit

524 68838 * Seal, Filler Tube 1022 272475 *** Gasket, Cover

525 496113 Tube, Oil Filler 1023 224552 Cover, RockerArm

535 272403 Element, Filter 1026 494432 Rod, Push, Intake

537 281106 * O-Ring, Air Cleaner 495136 Rod, Push, Exhaust

544 497603 Armature, Starter 1029 224554 Arm, Rocker

552 231597 Bushing, Govemor Crank 1033 495992 Valve Overhaul Kit

562 92613 BoLt,Carriage 1034 495248 Guide Assembly, Push Rod

592 231082 Nut, Hex 1044 94673 Screw, Hex Head

601 93053 Clamp, Fuel Pipe 1054 270723 Tie, Cable

611 493496 Elbow, Fuel Pipe 1058 272623 Manual, Owner's

614 93306 Pin, Cotter 1090 497607 Retainer, Brush

618 262803 Spring, Choke Return

634 281168 ** Seal, Choke Shaft RPM Settings: Low: 1650_1850, High: 3200-3400

634A 491323 * Seal, Governor

634B 281167 ** Washer, Throttle Shaft * Included in Gasket Set (495993)

635 280872 Boot, Spark Plug

646 224546 Brace, Air Cleaner ** Included in Carburetor Kit (497535)

657 93496 Screw, Sems

663 94620 Screw, Self-Tapping *** Included in both Gasket Set (495993) and

668 280848 Spacer Valve Overhaul Kit (495992)

718 230192 Pin, Dowel

726 392134 Gear, Ring **** Included in Gasket Set (495993), Carburetor Kit

(Includes Mounting Hardware) (497535) and Carburetor Gasket Set (494385)

727 490324 Cover, Starter

728 94627 Screw, Hex Head NOTE: All component dimensions given in U.So inches

729 281390 Clip, Wire 1inch = 25,4 mm

,t

53

SERVICE

54

SUGGESTED GUIDE FOR SiGHTiNG SLOPES FOR SAFE OPERATION

O1

01

SIGHTING

GUIDE

ONLY RIDE UP AND DOWN HILL,

NOT ACROSS HILL

SIGHT AND HOLD THIS LEVEL WITH

SKY LINE OR TREE.

15 °,MAX,

'_ .,_ Operate your Tractor up and down the face of slopes (not I

AA greater than 15°), never across the face. Make turns gradu- J

ally to prevent tipping or loss of control, Exercise extreme I

t

OWN R'S

MANUAL

MODEL NO=

917.258524

iF YOU NEED

REPAIR SERVICE

OR PARTS:

FOR REPAIR SERVICE, CALL

THIS TOLL FREE NUMBER:

1-800-4-REPAIR

(1-800-473-7247)

FOR REPLACEMENT PARTS

INFORMATION AND

ORDERING, CALL THIS

TOLL FREE NUMBER:

1-800-FON-PART

(1-800-366-7278)

FOR CONSUMER ASSISTANCE

HOT LINE, CALL THIS

TOLL FREE NUMBER:

1-800-659-5917

CRRFTSMI:IN®

15.5 HP IC

ELECTRIC START

42" MOWER

6 SPEED TRANSAXLE

LAWN TRACTOR

Each tractor has its own mode! number., Each engine has

its own modet number

The mode! number for your tractor will be found on the

model plate located under the seat.

The model number for your engine will be found on the

blower housing of the engine..

All parts listed herein may be ordered from any Sears,

Roebuck and Co. Service CentedDepartment and most Re-

tail Stores.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

oPRODUCT., TRACTOR

°MODEL NUMBER - 917.258524

°ENGINE MODEL NO. - 28N707, TYPE NO. 0173-01

oPART NUMBER

oPART DESCRIPTION

Your Sears merchandise has added value when you

consider Sears has service units nationwide staffed with

Sears trained technicians .... professional technicians

specifica!ly trained to insure that we meet our pledge to

you, we service what we sell

160917 Rev+2 t0.30,.97 KFSW

IIIIIIIIIIIIIIIIIII IIII I IIII I IIIIIII IIIIIIII IIIIIIIIIIIIIII IIIIIIIII

Printed in U.S,.A.