Craftsman 917273752 User Manual LAWN TRACTOR Manuals And Guides L0404217

CRAFTSMAN Lawn, Tractor Manual L0404217 CRAFTSMAN Lawn, Tractor Owner's Manual, CRAFTSMAN Lawn, Tractor installation guides

User Manual: Craftsman 917273752 917273752 CRAFTSMAN LAWN TRACTOR - Manuals and Guides View the owners manual for your CRAFTSMAN LAWN TRACTOR #917273752. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman LAWN TRACTOR Manual

Open the PDF directly: View PDF .
Page Count: 56

Download
Open PDF In Browser	View PDF

Owner's Manual

JCRIIFTSMIIN'J
LAWN TRACTOR
180 HP, 42" Mower
Electric Start
6 Speed Transaxle
Model No.
917.273752

IIL.-_II

This product has a low emission engine which operates
differently from previously built engines, Before you start the
engine, read and understand this Owner's Manual. J

IMPORTANT:

For answers to your questions about

Read and follow all Safety
Rules and Instructions before

this product, Call:

operating this equipment

Sears Craftsman Help Line
5 am - 5 pm, Mon- Sat

1-800-659-5917

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website:www.sears.com/craftsman

]

Warranty .................................................
2
Safety Rules ...........................................
3
Product Specifications ............................ 6
Assembly/P re-Operation ........................ 8
Operation ..............................................
11
Maintenance Schedule ......................... 17

Maintenance .........................................
17
Service and Adjustments ...................... 21
Storage .................................................
27
Troubleshooting ....................................
28
Repair Parts ..........................................
32
Sears Service ......................... Back Cover

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT
For two (2) years from the date of purchase, if this Craftsman Riding Equipment is
maintained, lubricated and tuned up according to the instructions in the owner's manual,
Sears will repair or replace free of charge any parts that are found to be defective in
material or workmanship according to the guidelines of coverage listed below. Sears will
also provide free labor for these applicable warranted parts for the two full years. During
the first 30 days of purchase, there will be no charges to service the product at your
home for issues covered by this warranty. (See exclusions below). For your convenience, IN HOME warranty service will still be available after the first 30 days of purchase, but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized Sears location. For the nearest authorized Sears location,
please call 1-800-4-MY-HOME®.
This warranty applies only while this product is within
the United States.
This Warranty does not cover:
• Expendable items which become worn during normal use, including but not limited to
blades, spark plugs, air cleaners, belts, and oil filters.
Standard Maintenance Servicing, oil changes, or tune-ups
• Tire replacement or repair caused by punctures from outside objects, such as nails,
thorns, stumps, or glass.
• Repairs necessary because of operator abuse, including but not limited to, damage
caused by towing objects beyond the capability of the riding equipment, impacting
objects that bend the frame or crankshaft, or over-speeding the engine.
• Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical damage caused by improper storage, failure to use the proper
grade and amount of engine oil, failure to keep the deck clear of flammable debris,
or failure to maintain the equipment according to the instructions contained in the
owner's manual.
• Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized (stale). In general, fuel should be used within 30 days of its purchase date.
• Normal deterioration and wear of the exterior finishes, or product label replacement.
Riding equipment used for commercial or rental purposes.
LIMITED WARRANTY ON BATTERY
For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in material or workmanship and our testing determines the battery
will not hold a charge, Sears will replace the battery at no charge. During the first 30
days of purchase, there will be no charges to replace the battery at your HOME. After
the first 30 days, for your convenience, IN-HOME warranty service will still be available but a trip charge will apply. This charge will be waived if the Craftsman product is
dropped off at an authorized Sears location. For the nearest authorized Sears location,
please call 1-800-4-MY-HOME®.
This battery warranty applies only while this product is within the United States.
This warranty gives you specific legal rights, and you may also have other rights, which
vary, from state to state.

Sears, Roebuck and Co.,Dept.817WA, Hoffman Estates, IL 60179
2

IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious
injury or death.
Be aware of the mower discharge direction and do not point it at anyone. Do
not operate the mower without either
the entire grass catcher or the guard in
place.
Slow down before turning.
Never leave a running machine unattended. Always turn off blades, set
parking brake, stop engine, and remove
keys before dismounting.
Turn off blades when not mowing.
Stop engine before removing grass
catcher or unclogging chute.
Mow only in daylight or good artificial
light.
Do not operate the machine while under
the influence of alcohol or drugs.
Watch for traffic when operating near or
crossing roadways.
Use extra care when loading or unloading the machine into a trailer or
truck.
Data indicates that operators, age 60
years and above, are involved in a large
percentage of riding mower-related injuries. These operators should evaluate
their ability to operate the riding mower
safely enough to protect themselves and
others from serious injury.
Keep machine free of grass, leaves or
other debris build-up which can touch
hot exhaust / engine parts and burn. Do
not allow the mower deck to plow leaves
or other debris which can cause buildup to occur. Clean any oil or fuel
spillage before operating or storing the
machine. Allow machine to cool before
storage.

_,WARNING:
In order to prevent accidental starting when setting up, transporting, adjusting or making repairs,
always disconnect spark plug wire and
place wire where it cannot contact spark
plug.
_tLWARNING:
Do not coast down a hill in
neutral, you may lose control of the tractor.
_,WARNING:
Tow only the attachments
that are recommended by and comply with
specifications of the manufacturer of your
tractor. Use common sense when towing.
Operate only at the lowest possible speed
when on a slope. Too heavy of a load,
while on a slope, is dangerous. Tires can
lose traction with the ground and cause
you to lose control of your tractor.
_,WARNING:
Engine exhaust, some of
its constituents, and certain vehicle components contain or emit chemicals known
to the State of California to cause cancer
and birth defects or other reproductive
harm.
_I_,WARNING: Battery posts, terminals
and related accessories contain lead and
lead compounds, chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
I. GENERAL
OPERATION
• Read, understand, and follow all instructions in the manual and on the machine
before starting.
• Only allow responsible adults, who are
familiar with the instructions, to operate
the machine.
• Clear the area of objects such as rocks,
toys, wire, etc., which could be picked
up and thrown by the blade.
• Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely necessary. Always look down and
behind before and while backing.

II. SLOPE

OPERATION

Slopes are a major factor related to lossof-control and tipover accidents, which can
result in severe injury or death. All slopes
require extra caution. If you cannot back
up the slope or if you feel uneasy on it, do
not mow it.

DO:

• Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.

• Mow up and down slopes, not across.
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
• Use slow speed. Choose a low gear
so that you will not have to stop or shift
while on the slope.
• Follow the manufacturer's recommendations for wheel weights or counterweights to improve stability.
• Use extra care with grass catchers or
other attachments. These can change
the stability of the machine.
• Keep all movement on the slopes slow
and gradual Do not make sudden
changes in speed or direction.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.
DO NOT:

IV. SERVICE
• Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
• Never run a machine inside a closed
area.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never make adjustments or repairs with
the engine running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Check brake operation frequently. Adjust and service as required.

• Do not turn on slopes unless necessary, and then, turn slowly and gradually
downhill, if possible.
• Do not mow near drop-offs, ditches,
or embankments. The mower could
suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge
caves in.
• Do not mow on wet grass. Reduced
traction could cause sliding.
• Do not try to stabilize the machine by
putting your foot on the ground.
• Do not use grass catcher on steep
slopes.

III, CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the machine and the mowing activity. Neverassume that children will remain where you
last saw them.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and down for small children.

• Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
• Never carry passengers or children
even with the blades off.
• Do not mow in reverse unless absolutely necessary. Always look down and
behind before and while backing.
• Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and down for small children.
• Mow up and down slopes (15 ° Max), not
across.

• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Uneven
terrain could overturn the machine. Tall
grass can hide obstacles.
• Use slow speed. Choose a low gear
so that you will not have to stop or shift
while on the slope.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.
• If machine stops while going uphill,
disengage blades, shift into reverse and
back down slowly.
• Do not turn on slopes unless necessary,
and then, turn slowly and gradually
downhill, if possible.

PRODUCT
SPECIFICATIONS
Gasoline
1.25
Capacity and
Unleaded
Type:
Regular
Oil Type
API-SG-SL):

SAE 30 (above 32°F)
SAE 5W-30(below 32°F

Oil Capacity:

W/Filter:
3.5 Pints
W/O Filter: 3.0 Pints

Spark Plug:
(Gap: .030")

Champion

RC12YC

Ground Speed
(MPH):

Forward:
1st
2nd
3rd
4th
5th
6th
Reverse:
Front:
Rear:

1.2
1.5
2.4
3.5
4.8
5.3
1.5
14 PSI
10 PSI

Tire Pressure:

laws (if any). If a spark arrester is used, it
should be maintained in effective working
order by the operator.
In the state of California the above is required by law (Section 4442 of the California Public Resources Code). Other states
may have similar laws. Federal laws apply
on federal lands. A spark arrester for the
muffler is available through your nearest
Sears service center (See REPAIR PARTS
section of this manual).
REPAIR PROTECTION
AGREEMENTS
Congratulations on making a smart purchase. Your new Craftsman_ product is
designed and manufactured for years of
dependable operation. But like all products,
it may require repair from time to time. That's
when having a Repair Protection Agreement
can save you money and aggravation.
Purchase a Repair Protection Agreement
now and protect yourself from unexpected
hassle and expense.
Here's what's included in the Agreement:
• Expert service by our 12,000 profesional repair specialists.
• Unlimited service and no charge for
parts and labor on all covered repairs.
• Product replacement if your covered
product can't be fixed.
• Discount of 10% from regular price of
service and service-related parts not
covered by the agreement; also, 10%
off regular price of preventive maintenance check.
• Fast help by phone - phone support
from a Sears technician on products
requiring in-home repair, plus convenient repair scheduling.
Once you purchase the Agreement, a
simple phone call is all that it takes for you
to schedule service. You can call anytime
day or night, or schedule a service appointment online.
Sears has over 12,000 professional repair
specialists, who have access to over 4.5
million quality parts and accessories.
That's the kind of professionalism you can
count on to help prolong the life of your
new purchase for years to come. Purchase
your Repair Protection Agreement today!
Some limitations
and exclusions apply.
For prices and additional
information
call 1-800-827-6655.

Charging System: 3 Amps Battery
5 Amps Headlights
Battery:

Amp/Hr:
28
Min. CCA: 230
Case Size: U1R

Blade Bolt Torque: 27-35 Ft. Lbs.
CONGRATULATIONS
on your purchase
of a new tractor. It has been designed,
engineered and manufactured to give
you the best possible dependability and
performance.
Should you experience any problem you
cannot easily remedy, please contact a
Sears or other qualified service center.
We have competent, well-trained technicians and the proper tools to service or
repair this tractor.
Please read and retain this manual. The
instructions will enable you to assemble
and maintain your tractor properly. Always
observe the "SAFETY RULES".
CUSTOMER
RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for and using your tractor.
• Follow the instructions under "Maintenance" and "Storage" sections of this
owner's manual.
_,WARNING:
This tractor is equipped
with an internal combustion engine and
should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine's
exhaust system is equipped with a spark
arrester meeting applicable local or state

SEARS

INSTALLATION

SERVICE

For Sears professional installation of home
appliances, garage door openers, water
heaters, and other major home items, in
the U.S.A. call 1-800-4-MY-HOME®
6

Steering Wheel

Steering
Wheel Insert

(1) Large Flat Washer

@
(1) Hex Bolt 1/4-28 x 1-1/4

(1) Locknut

1/2-20

(1) Locknut

_£
Adapter
Steering
Wheel

1/4-28

Steering
Extension
teering
Boot

Shaft

Seat

@
_(1)

(1)Washer
17/32 x 1-3/16 x 12 Gauge
Knob

For Future Use

Keys

Slope

Sheet

(2) Keys

Video

Cassette

Your new tractor has been assembled at the factory with the exception of those parts left
unassembled for shipping purposes. To ensure safe and proper operation of your tractor
all parts and hardware you assemble must be tightened securely. Use the correct tools
as necessary to insure proper tightness. Review the video cassette before you begin.
TOOLS REQUIRED
FOR
ASSEMBLY
A socket wrench set will make assembly
easier. Standard wrench sizes you need
are listed below.
(1) 3/4"wrench
(1) Pliers
(2) 7/16" wrench
(1) Utility knife
(1) Tire pressure gauge

_-----[_

_
,

Steering
Wheel

g
Boot

When right or left hand is mentioned in
this manual, it means when you are in
the operating position (seated behind the
steering wheel).
TO REMOVE
CARTON
UNPACK

TRACTOR

1/2 Hex Nut
Insert
Large Flat
Washer

7Tabs

FROM
Shaft

CARTON

1. Remove all accessible loose parts and
parts boxes from carton.
2. Cut along dotted lines on all four panels of carton. Remove end panels and
lay side panels flat.
3. Check for any additional loose parts or
cartons and remove.
BEFORE
REMOVING
TRACTOR
FROM SKID
ATTACH STEERING WHEEL

7. Snap steering wheel insert into center
of steering wheel.
8. Remove protective materials from tractor hood and grill.
IMPORTANT: Check for and remove any
staples in skid that may puncture tires
where tractor is to roll off skid.

ASSEMBLE EXTENSION SHAFT AND
BOOT
1. Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4
hex bolt and Iocknut. Tighten securely.
IMPORTANT: Tighten bolt and nut securely to 10-12 ft. Ibs torque.
2. Place tabs of steering boot over tab
slots in dash and push down to secure.
INSTALL

STEERING

INSTALL

SEAT

Adjust seat before tightening adjustment
knob.
1. Remove adjustment knob and flat
washer securing seat to cardboard
packing and set aside for assembly of
seat to tractor.
2. Pivot seat upward and remove from
the cardboard packing. Remove the
cardboard packing and discard.
3. Place seat on seat pan so head of
shoulder bolts are positioned over the
large slotted holes in pan.
4. Push down on seat to engage shoulder
bolts in slots and pull seat towards rear
of tractor.

WHEEL

3. Position front wheels of the tractor so
they are pointing straight forward.
4. Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft extension.
5. Position steering wheel so cross bars
are horizontal (left to right) and slide
inside boot and onto adapter.
6. Assemble large flat washer, 1/2 hex
nut and tighten securely.

5. Pivot seat and pan forward and assemble adjustment knob and flat
washer loosely. Do not tighten.
6. Lower seat into operating position and
sit in seat.
7. Slide seat until a comfortable position
is reached which allows you to press
clutch/brake pedal all the way down.
8. Get off seat without moving its adjusted position.
9. Raise seat and tighten adjustment
knob securely.

NOTE: You may now roll or drive your
tractor off the skid. Follow the appropriate
instruction below to remove the tractor
from the skid.
TO ROLL TRACTOR
OFF SKID (See
Operation
section for location and
function of controls)
1. Press lift lever plunger and raise
attachment lift lever to its highest position.
2. Release parking brake by depressing
clutch/brake pedal.
3. Place gearshift lever in neutral (N)
position.
4. Roll tractor forward off skid.
5. Remove banding holding deflector
shield up against tractor.
TO DRIVE TRACTOR
OFF SKID (See
Operation
section
for location
and
function
of controls)
_WARNING:
Before starting, read, understand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.
1. Be sure all the above assembly steps
have been completed.
2. Check engine oil level and fill fuel tank
with gasoline.
3. Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.
4. Place gear shift lever in neutral (N)
position.
5. Press lift lever plunger and raise
attachment lift lever to its highest position.
6. Start the engine. After engine has
started, move throttle control to idle
position.
7. Depress clutch/brake pedal into full
"BRAKE" position and hold. Move gearshift lever to 1st gear.
8. Slowly release clutch/brake pedal and
slowly drive tractor off skid.
9. Apply brake to stop tractor, set parking brake and place gearshift lever in
neutral position.
10.Turn ignition key to "STOP" position.
Continue with the instructions that follow.

Seat

Seat I

Shoulder
Bolts

Flat Washer

Adjustment Knob

CHECK BATTERY
1. Lift seat pan to raised position.
NOTE: If this battery is put into service
after month and year indicated on label
(label located between terminals) charge
battery for minimum of one hour at 6-10
amps. (See "BATTERY" in Maintenance
section of this manual for charging instructions).
Seat

Terminal

INSTALL MULCHER
PLATE
(If previously
removed)
1. Raise and hold deflector shield in
upright position.
2. Place front of mulcher plate over front
of mower deck opening and slide into
place, as shown.
3. Hook front latch into hole on front of
mower deck.
4. Hook rear latch into hole on back of
mower deck.

CHECK

,/CHECKLIST
Before you operate and enjoy your new
tractor, we wish to assure that you receive
the best performance and satisfaction
from this Quality Product.
Please review the following checklist:
,/All assembly instructions have been
completed.
,/No remaining loose parts in carton.
,/Battery is properly prepared and
charged. (Minimum 1 hour at 6 amps).
,/Seat is adjusted comfortably and tightened securely.
,/All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).
,/Be sure mower deck is properly leveled
side-to-side/front-to-rear
for best cutting
results. (Tires must be properly inflated
for leveling).
,/Check mower and drive belts. Be sure
they are routed properly around pulleys
and inside all belt keepers.
,/Check wiring. See that all connections
are still secure and wires are properly
clamped.
While learning how to use your tractor, pay
extra attention to the following important
items:
,/Engine oil is at proper level.
,/Fuel tank is filled with fresh, clean, regular unleaded gasoline.
,/Become familiar with all controls - their
location and function. Operate them
before you start the engine.
,/Be sure brake system is in safe operating condition.

Mulcher
Plate

Latch
Hooks

TO CONVERTTO
BAGGING
OR
DISCHARGING
Simply remove mulcher plate and store in
a safe place.Your mower is now ready for
discharging or installation of optional grass
catcher accessory.
NOTE: It is not necessary to change
blades. The mulcher blades are designed
for discharging and bagging also.
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for shipping purposes.
Correct tire pressure is important for best
cutting performance.
• Reduce tire pressure to PSI shown in
"PRODUCT SPECIFICATIONS" section
of this manual.

CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly leveled. See "TO
LEVEL MOWER HOUSING" in the Service
and Adjustments section of this manual.
CHECK FOR PROPER
OF ALL BELTS

SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly
adjusted. See "TO ADJUST BRAKE" in
the Service and Adjustments section of
this manual.

,_CAUTION:
Do not remove deflector
shield from mower.
Deflector
Shield

BRAKE

POSITION

See the figures that are shown for replacing motion and mower blade drive belts
in the Service and Adjustments section
of this manual. Verify that the belts are
routed correctly.

These symbols may appear on your tractor or in literature supplied with the product.
Learn and understand their meaning.

R
REVERSE

ENGINE OFF

NEUTRAL

NIGH

LIGHTS ON

OVER TEMP
LIGHT

FUEL

ENGINE ON

OIL PRESSURE

I',,I

L
LOW

CHOKE

ENGINE START

BATTERY

FAST

PARKING

REVERSE

BRAKE

FORWARD

SLOW

IGNITION

PARKING BRAKE
LOCKED

MOWER

HEIGHT

PARKING BRAKE
UNLOCKED

MOWER

LIFT

@@@@@
ATTACHMENT
CLUTCH ENGAGED

ATTACHMENT
CLUTCH DISENGAGED

&
&
&

FREE WHEEL
(Automatic

Models

DANGER, KEEP HANDS
AND FEET AWAY

only)

(SEE SAFETY

SLOPE

HAZARDS

RULES SECTION)

DANGER indicatesa hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicatesa hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.

Failure to follow instructions
could result in serious

KEEP AREA CLEAR

injury or

death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.

._..

HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.

injury

KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of
various controls and adjustments. Save this manual for future reference.

Attachment
Clutch Lever

Light Switch
Position

Ignition Switch

Ammeter
Lever
Plunger

-Throttle/Choke
Control

Attachment
Lift Lever

Height
Adjustment

Clutch/Brake
Pedal

Brake Lever

Gearshift Lever

Our tractors conform to the safety standards of the
American National Standards Institute.
AMMETER - Indicates charging (+) or
discharging (-) of battery.
ATTACHMENT CLUTCH LEVER - Used
to engage the mower blades, or other attachments mounted to your tractor.
ATTACHMENT LIFT LEVER - Used to
raise, lower, and adjust the mower deck or
other attachments mounted to your tractor.
CLUTCH/BRAKE
PEDAL - Used for
declutching and braking the tractor and
starting the engine.
GEARSHIFT LEVER - Selects the speed
and direction of tractor.

IGNITION SWITCH - Used for starting and
stopping the engine.
LIFT LEVER PLUNGER - Used to release
attachment lift lever when changing its
position.
LIGHT SWITCH POSITION -Turns the
headlights on and off.
PARKING BRAKE LEVER - Locks clutch/
brake pedal into the brake position.
THROTTLE/CHOKE
CONTROL - Used
for starting and controlling engine speed.

The operation of any tractor can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend a wide vision safety mask over
spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

IMPORTANT: Leaving the ignition switch
in any position other than "STOP" will
cause the battery to discharge and go
dead.
NOTE: Under certain conditions when
tractor is standing idle with the engine
running, hot engine exhaust gases may
cause "browning" of grass. To eliminate
this possibility, always stop engine when
stopping tractor on grass areas.
_CAUTION.Always stop tractor completely, as described above, before leaving
the operator's position.
TO USE THROTTLE CONTROL

TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator
to leave the seat without first setting the
parking brake will shut off the engine.
1. Depress clutch/brake pedal all the way
down and hold.
2. Pull parking brake lever up and release
pressure from clutch/brake pedal.
Pedal should remain in brake position.
Make sure parking brake will hold tractor secure.
Attachment Clutch Lever
Position

Thn
Choke --_
Control

"Disengaged"
Position

Always operate engine at full throttle.
• Operating engine at less than full
throttle reduces the battery charging
rate.
• Full throttle offers the best bagging and
mower performance.

inition Key
"Disengaged"
Position
/ Parking Brake
"Engaged"
Position

"Brake"
Position

TO MOVE

FORWARD

AND BACKWARD

The direction and speed of movement is
controlled by the gearshift lever.
1. Start tractor with clutch/brake pedal depressed and gearshift lever in neutral
(N) position.
2. Move gearshift lever to desired position.
3. Slowly release clutch/brake pedal to
start movement.
IMPORTANT: Bring tractor to a complete
stop before shifting or changing gears.
Failure to do so will shorten the useful life
of your transaxle.

Lever

STOPPING

MOWER BLADES • To stop mower blades, move attachment
clutch lever to "DISENGAGED" position.
GROUND DRIVE -

TO ADJUST

• To stop ground drive, depress clutch/
brake pedal all the way down.
• Move gearshift lever to neutral (N)
position.
ENGINE -

MOWER

CUTTING

HEIGHT

The position of the attachment lift lever
determines the cutting height.
• Grasp lift lever.
• Press plunger with thumb and move
lever to desired position.
The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with
the engine not running. These heights
are approximate and may vary depending
upon soil conditions, height of grass and
types of grass being mowed.

• Move throttle control to slow position.
NOTE: Failure to move throttle control
to slow position and allowing engine to
idle before stopping may cause engine to
"backfire".
• Turn ignition key to "STOP" position and
remove key. Always remove key when
leaving tractor to prevent unauthorized
use.
• Never use choke to stop engine.

• The average lawn should be cut to approximately 2-1/2 inches during the cool season
and to over 3 inches during hot months.
For healthier and better looking lawns, mow
often and after moderate growth.
• For best cutting performance, grass over
6 inches in height should be mowed
twice. Make the first cut relatively high;
the second to desired height.
TO ADJUST GAUGE WHEELS

Attachment /
Clutch Lever

"Disengag
Position

Gauge wheels are properly adjusted
when they are slightly off the ground when
mower is at the desired cutting height in
operating position. Gauge wheels then
keep the deck in proper position to help
prevent scalping in most terrain conditions.
NOTE: Adjust gauge wheels with tractor
on a flat level surface.
1. Adjust mower to desired cutting height
(See "TO ADJUST MOWER CUTTING
HEIGHT" in this section of manual).
2. With mower in desired height of cut
position, gauge wheels should be assembled so they are slightly off the ground.
Install gauge wheel in appropriate hole
with shoulder bolt, 3/8 washer, and 3/816 Iocknut and tighten securely.
3. Repeat for opposite side, installing
gauge wheel in same adjustment hole.
Gauge Wheel
o_
Mounting \ _-_

Locknut

_,,,J/_
V_-_,_-_

3/8 Washer f_,v_.,
Gauge Wheel
TO OPERATE

Shield

TO OPERATE ON HILLS
,_WARNING:
Do not drive up or down
hills with slopes greater than 15° and do
not drive across any slope. Use the slope
guide at the back of this manual.
• Choose the slowest speed before starting up or down hills.
• Avoid stopping or changing speed on
hills.
• If slowing is necessary, move throttle
control lever to slower position.
• If stopping is absolutely necessary, push
clutch/brake pedal quickly to brake position and engage parking brake.
• Move gearshift lever to 1st gear. Be
sure you have allowed room for tractor
to roll slightly as you restart movement.
• To restart movement, slowly release
parking brake and clutch/brake pedal.
• Make all turns slowly.

_/_

TO TRANSPORT
• Raise attachment lift to highest position
with attachment lift control.
• When pushing or towing your tractor,
be sure gearshift lever is in neutral (N)
position.
• Do not push or tow tractor at more than
five (5) MPH.
NOTE: To protect hood from damage
when transporting your tractor on a truck
or a trailer, be sure hood is closed and
secured to tractor. Use an appropriate
means of tying hood to tractor (rope, cord,
etc.).

"_J
Shoulder

jBOIt

MOWER

Your tractor is equipped with an operator
presence sensing switch. Any attempt
by the operator to leave the seat with the
engine running and the attachment clutch
engaged will shut off the engine. You must
remain fully and centrally positioned in the
seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough, rolling terrain or hills.
1. Select desired height of cut.
2. Start mower blades by engaging attachment clutch control.
TO STOP MOWER BLADES disengage attachment clutch control.
_,CAUTION:
Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.

Lift
Lever High Position

TOWING
MENTS

CARTS

AND OTHER

ATTACH-

Tow only the attachments that are recommended by and comply with specifications
of the manufacturer of your tractor. Use
common sense when towing. Too heavy
of a load, while on a slope, is dangerous.
Tires can lose traction with the ground and
cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL

TO START ENGINE
When starting the engine for the first time
or if the engine has run out of fuel, it will
take extra cranking time to move fuel from
the tank to the engine.
1. Sit on seat in operating position,
depress clutch/brake pedal and set
parking brake.
2. Place gear shift lever in neutral (N)
position.
3. Move attachment clutch to disengaged
position.
4. Move throttle control to choke position.
NOTE: Before starting, read the warm
and cold starting procedures below.
5. Insert key into ignition and turn key
clockwise to start position and release
key as soon as engine starts. Do
not run starter continuously for more
than fifteen seconds per minute. If the
engine does not start after several
attempts, move throttle control to fast
position, wait a few minutes and try
again. If engine still does not start,
move the throttle control back to the
choke position and retry.

The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.
1. Check engine oil with tractor on level
ground.
2. Remove oil fill cap/dipstick and wipe
clean, reinsert the dipstick and screw
cap tight, wait for a few seconds, remove and read oil level. If necessary,
add oil until "FULl" mark on dipstick is
reached. Do not overfill.
• For cold weather operation you should
change oil for easier starting (See the
oil viscosity chart in the Maintenance
section of this manual).
• To change engine oil, see the Maintenance section in this manual.
ADD GASOLINE
• Fill fuel tank to bottom of filler neck. Do
not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil
with gasoline. Purchase fuel in quantities that can be used within 30 days to
assure fuel freshness.

WARM WEATHER STARTING (50 ° F and
above)
6. When engine starts, move the throttle
control to the fast position.
• The attachments and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above.

,_,CAUTION:
Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: When operating in temperatures below32°F(0°C), use fresh, clean
winter grade gasoline to help insure good
cold weather starting.
CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of acids during storage.
Acidic gas can damage the fuel system
of an engine while in storage. To avoid
engine problems, the fuel system should
be emptied before storage of 30 days
or longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.

COLD WEATHER STARTING ( 50 ° F and
below)
6. When engine starts, leave throttle
control in choke position until engine
warms up and begins to run roughly.
Once rough running begins, immediately move the throttle control to the
fast position. Engine warm-up may
take from several seconds to several
minutes (the colder the temperature,
the longer the warm-up).
• The attachments can also be used during the engine warm-up period.
NOTE: If at a high altitude (above 3000
feet) or in cold temperatures (below 32 F)
the carburetor fuel mixture may need to
be adjusted for best engine performance
(see "TO ADJUST CARBURETOR" in the
Service and Adjustments section of this
manual).

• Always operate engine at full throttle
when mowing to assure better mowing
performance and proper discharge of
material. Regulate ground speed by
selecting a low enough gear to give the
mower cutting performance as well as
the quality of cut desired.
• When operating attachments, select a
ground speed that will suit the terrain
and give best performance of the attachment being used.
MULCHING

MOWING

TIPS

IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. Clean after each use.
• The special mulching blade will recut
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried, the newly cut area will not be
exposed to direct sunlight.
• For best results, adjust the mower
cutting height so that the mower cuts
off only the top one-third of the grass
blades. For extremely heavy grass, reduce your width of cut on each pass and
mow slowly.

MOWING TIPS
• Mower should be properly leveled for
best mowing performance. See "TO
LEVEL MOWER HOUSING" in the
Service and Adjustments section of this
manual.
• The left hand side of mower should be
used for trimming.
• Drive so that clippings are discharged
onto the area that has already been
cut. Have the cut area to the right of
the tractor. This will result in a more
even distribution of clippings and more
uniform cutting.
• When mowing large areas, start by
turning to the right so that clippings will
discharge away from shrubs, fences,
driveways, etc. After one or two rounds,
mow in the opposite direction making
left hand turns until finished.

MAXI_

1
•

• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a second cut, mow across (perpendicular) to
the first cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.

• If grass is extremely tall, it should be
mowed twice to reduce load and possible fire hazard from dried clippings.
Make first cut relatively high; the second
to the desired height.
• Do not mow grass when it is wet.
Wet grass will plug mower and leave
undesirable clumps. Allow grass to dry
before mowing.

MAINTENANCE

SCHEDULE

FILL IN DATES
AS YOU COMPLETE
REGULAR
SERVICE
Check

Brake

Check

Tire Pressure

Operation

Check Operator Presence
Interlock Systems

Check

for Loose

Fasteners

Sharpen/Replace

Mower

Lubrication

Check

Battery

Clean

Battery

Check

Transaxle

Check

V-Belts

Check

Engine

Change

Level
and Terminals

Oil Level

Engine

Oil (with oil filte0

Engine

Oil (without

Change
Clean

Air Filter

Clean

Air Screen
Muffler/Spark

Replace
Clean

Cooling

Inspect

Blades

Chart

and

oil filte0

Attester

Oil Filter (If equipped)

Engine

Cooling

Fins

Replace

Spark

Replace

Air Filter Paper Cartridge

Replace

Fuel Filter

t - Change
in high
2 - Service

often

Plug

when

operating

ambient
temperatures.
more often when operatin(_

GENERAL

under
in dirty

a heavy
or dusty

lead or

3 - Replace
blades more often when mowing
in sandy soil.
4 - Not required
if equipped
with maintenance=free
baltery.
5 - Tighten
front axle pivot bolt to 35 ft.dbs, maximum.

conditions.

RECOMMENDATIONS
LUBRICATION

The warranty on this tractor does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator
must maintain tractor as instructed in this
manual.
Some adjustments will need to be made
periodically to properly maintain your
tractor.
At least once a season, check to see if
you should make any of the adjustments
described in the Service and Adjustments
section of this manual.
• At least once a year you should replace
the spark plug, clean or replace air filter,
and check blades and belts for wear.
A new spark plug and clean air filter
assure proper air-fuel mixture and help
your engine run better and last longer.

CHART
--

Zerk

@Front Wheel
Bearing

@ Spindle
Zerk

@Front Wheel
Bearing Zerk

Zerk

@Engine /
I
"d)Gearshift
Pivots
_SAE 30 or 10w30 Motor Oil
@General Purpose Grease
@Refer to Maintenance "ENGINE" Section

BEFORE EACH USE
f. Check engine oil level.
2. Check brake operation.
3. Check tire pressure.
4. Check operator presence and
interlock systems for proper operation.
5. Check for loose fasteners.

IMPORTANT: Do not oil or grease the
pivot points which have special nylon
bearings. Viscous lubricants will attract
dust and dirt that will shorten the life of the
self-lubricating bearings. If you feel they
must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

TRACTOR

IMPORTANT: To ensure proper assembly,
center hole in blade must align with star
on mandrel assembly.
4. Reassemble blade bolt, lock washer
and flat washer in exact order as
shown.
5. Tighten blade bolt securely (27-35 Ft.
Lbs. torque).
IMPORTANT:
Blade bolt is heat treated.
If bolt needs replacing, replace only with
approve bolt shown in the Repair Parts.

Always observe safety rules when performing any maintenance.
BRAKE OPERATION
If tractor requires more than six (6) feet
stopping distance at high speed in highest
gear, then brake must be adjusted. (See
"TO ADJUST BRAKE" in the Service and
Adjustments section of this manual).
TIRES
• Maintain proper air pressure in all tires
(See "PRODUCT SPECIFICATIONS"
section of this manual).
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, tire sealant
may be purchased from your local parts
dealer. Tire sealant also prevents tire dry
rot and corrosion.
OPERATOR PRESENCE SYSTEM

Mandrel As,_embly
Trailing _
Edge Up

BI_,_,,
_"_'"i"

Center _
Hqle _(

Flat Washer_-_L

_'_'_
_

J (_

Lock _r__

\Star

t%_-Blade Bolt

TO SHARPEN

BLADE

NOTE: We do not recommend sharpening blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will cause
excessive vibration and eventual damage
to mower and engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
• Slide blade on to an unthreaded portion
of the steel bolt or pin and hold the
bolt or pin parallel with the ground. If
blade is balanced, it should remain in a
horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.

Be sure operator presence and interlock
systems are working properly. If your tractor does not function as described, repair
the problem immediately.
• The engine should not start unless the
clutch/brake pedal is fully depressed
and attachement clutch control is in the
disengaged position.
• When the engine is running, any attempt by the operator to leave the seat
without first setting the parking brake
should shut off the engine.
• When the engine is running and the
attachment clutch is engaged, any attempt by the operator to leave the seat
should shut off the engine.
• The attachment clutch should never operate unless the operator is in the seat.
BLADE CARE
For best results mower blades must be
kept sharp. Replace bent or damaged
blades.
BLADE REMOVAL
1. Raise mower to highest position to allow access to blades.
2. Remove blade bolt, lock washer and
flat washer securing blade.
3. Install new or resharpened blade
with trailing edge up towards deck as
shown.

5/8" Bolt c
Pin
Center Hole

Blade

BATTERY
Your tractor has a battery charging system
which is sufficient for normal use. However, periodic charging of the battery with
an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on
your tractor is maintenance free. Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary.
TO CLEAN BATTERY AND TERMINALS

NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, they will result in increased
oil consumption when used above 32°E
Check your engine oil level more frequently to avoid possible engine damage from
running low on oil.
Change the oil after every 50 hours of operation or at least once a year if the tractor
is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine and after each eight (8)
hours of operation. Tighten oil fill cap/
dipstick securely each time you check the
oil level.

Corrosion and dirt on the battery and
terminals can cause the battery to "leak"
power.
1. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.
2. Rinse the battery with plain water and
dry.
3. Clean terminals and battery cable ends
with wire brush until bright.
4. Coat terminals with grease or petroleum jelly.
5. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

TO CHANGE

ENGINE

OIL

Determine temperature range expected
before oil change. All oil must meet API
service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
1. Remove oil fill cap/dipstick. Be careful
not to allow dirt to enter the engine
when changing oil.
2. Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting.
Oil Drain Valve

TRANSAXLE COOLING
Keep transaxle free from build-up of dirt
and chaff which can restrict cooling.
Drain

V-BELTS
Check V-belts for deterioration and wear
after 100 hours of operation and replace
if necessary. The belts are not adjustable.
Replace belts if they begin to slip from
wear.

Tube

3. Unlock drain valve by pushing inward
slightly and turning counterclockwise.
4. To open, pull out on the drain valve.
5. After oil has drained completely, close
and lock the drain valve by pushing
inward and turning clockwise until the
pin is in the locked position as shown.
6. Remove the drain tube and replace the
cap onto the end of the drain valve.
7. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill.
For approximate capacity see "PRODUCT SPECIFICATIONS" section of this
manual.
8. Use gauge on oil fill cap/dipstick for
checking level. For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick. Keep oil
at "FULl.:' line on dipstick. Tighten cap
onto the tube securely when finished.

ENGINE
LUBRICATION
Only use high quality detergent oil rated
with API service classification SG-SL.
Select the oil's SAE viscosity grade
according to your expected operating
temperature.
SAE VISCOSITY

.30
TEMPERATURE

.IO

GRADES

RANGEANTBCIPATEDSEFORENEXTOILCHANGE
oi_ vl_c cha_El

ENGINE OIL FILTER
Replace the engine oil filter every season
or every other oil change if the tractor is
used more than 100 hours in one year.

CLEAN AIR SCREEN
Air screen must be kept free of dirt and
chaff to prevent engine damage from
overheating. Clean with a wire brush or
compressed air to remove dirt and stubborn dried gum fibers.
ENGINE COOLING SYSTEM

AIR FILTER
Your engine will not run properly using a
dirty air filter. Replace pre-cleaner after
every 25 hours of operation or every
season. Service paper cartridge every
100 hours of operation or every season,
whichever occurs first.
Service air cleaner more often under dusty
conditions.
1. Pull up on air filter cover handle and
rotate towards engine.
2. Remove cover.
3. Carefully remove air filter cartridge and
pre-cleaner from base.
4. Clean base carefully to prevent debris
from falling into carburetor.
NOTE: If very dirty or damaged, replace
cartridge.
5. Place new pre-cleaner and cartridge
firmly in base.
6. Align tabs on cover with slots in blower
housing and replace cover.
7. Hook handle on cover and push down
on handle to close.
IMPORTANT: Petroleum solvents, such
as kerosene, are not to be used to clean
the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean
cartridge.

Debris may clog the engine's air cooling system. Remove blower housing and
clean area shown to prevent overheating
and engine damage.
Clean out chaff and debris

Air Screen

MUFFLER
Inspect and replace corroded muffler and
spark arrester (if equipped) as it could create a fire hazard and/or damage.
SPARK PLUG(S)
Replace spark plug(s) at the beginning
of each mowing season or after every
100 hours of operation, whichever occurs
first. Spark plug type and gap setting are
shown in "PRODUCT SPECIFICATIONS"
section of this manual.
IN-LINE FUEL FILTER
The fuel filter should be replaced once
each season. If fuel filter becomes
clogged, obstructing fuel flow to carburetor, replacement is required.
1. With engine cool, remove filter and
plug fuel line sections.
2. Place new fuel filter in position in fuel
line with arrow pointing towards carburetor.
3. Be sure there are no fuel line leaks
and clamps are properly positioned.
4. Immediately wipe up any spilled gasoline.

jCover

Cartridge

Slots

Clamp /

Clamp
_

.j.._y
_ Fuel Filter

CLEANING
• Clean engine, battery, seat, finish, etc.
of all foreign matter.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• Protect painted surfaces with automotive type wax.

We do not recommend using a garden
hose or pressure washer to clean your
tractor unless the engine and transmission are covered to keep water out. Water
in engine or transmission will shorten the
useful life of your tractor. Use compressed
air or a leaf blower to remove grass,
leaves and trash from tractor and mower.

SERVICE
WARNING: ORTOADJUSTMENTS:
AVOID SERIOUS INJURY, BEFORE PERFORMING ANY
1. Depress clutch/brake pedal fully and set parking brake.
2. Place gearshift lever in neutral (N) position.
3. Place attachment clutch in "DISENGAGED" position.
4. Turn ignition key to "STOP" and remove key.
5. Make sure the blades and all moving parts have completely stopped.
6. Disconnect spark plug wire from spark plug and place wire where it cannot
come in contact with plug.

TRACTOR

6. Disconnect anti-sway bar from chassis
bracket by removing retainer spring.
7. Disconnect suspension arms from rear
deck brackets by removing retainer
springs.
8. Disconnect front links from deck by
removing retainer springs.
9. Raise lift lever to raise suspension
arms. Slide mower out from under tractor.
IMPORTANT: If an attachment other than
the mower deck is to be mounted on the
tractor, remove the front links and hook
the clutch spring Into square hole in frame.

TO REMOVE MOWER
Mower will be easier to remove from the
right side of tractor.
1. Place attachment clutch in "DISENGAGED" position.
2. Move attachment lift lever forward to
lower mower to its lowest position.
3. Roll belt off engine pulley.
4. Remove small retainer spring, and
remove clutch spring off pulley bolt.
5. Remove large retainer spring, slide
collar off and push housing guide out
of bracket.

Small Retainer
Clutch
Small
Clutch Spring

Link

Retainer S
Anti-Sway
Retainer Springs
Both Sides)

Housing

Bracket
Large Retainer Spring

TO INSTALL MOWER
1. Raise attachment lift lever to its highest
position.
2. Slide mower under tractor with deflector shield to right side of tractor.
3. Lower lift lever to its lowest position.
4. Connect front links to mower deck and
secure with retainer springs.
5. Connect suspension arms to rear
deck brackets and secure with retainer
springs.
6. Connect anti-sway bar to chassis
bracket and secure with retainer spring.
7. Push clutch cable housing guide into
bracket, slide collar onto guide and
secure with large retainer spring.
8. Place flat washer and clutch spring on
idler pulley bolt and secure with small
retainer spring.
9. Install belt onto engine pulley.

FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to
side. If the following front-to-back adjustment is necessary, be sure to adjust both
front links equally so mower will stay level
side-to-side.
To obtain the best cutting results, the
mower housing should be adjusted so
that the front is approximately 1/8" to 1/2"
lower than the rear when the mower is in
its highest position.
Check adjustment on right side of tractor. Measure distance "D" directly in front
and behind the mandrel at bottom edge of
mower housing as shown.
• Before making any necessary adjustments, check that both front links are
equal in length.
• If links are not equal in length, adjust
one link to same length as other link.
• To lower front of mower loosen nut "E"
on both front links an equal number of
turns.
• When distance "D" is 1/8" to 1/2"
lower at front than rear, tighten nuts "F"
against trunnion on both front links.
• To raise front of mower, loosen nut "F"
from trunnion on both front links. Tighten
nut "E" on both front links an equal number of turns. The two front links must
remain equal in length.
• When distance "D" is 1/8" to 1/2" lower
at front than rear, tighten nut "F" against
trunnion on both front links.
• Recheck side-to-side adjustment.

TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked
on level ground or driveway. Make sure
tires are properly inflated (See "PRODUCT SPECIFICATIONS" section of this
manual). If tires are over or underinflated,
you will not properly adjust your mower.
SIDE-TO-SIDE ADJUSTMENT
• Raise mower to its highest position.
• At the midpoint of both sides of mower,
measure height from bottom edge of
mower to ground. Distance "A" on both
sides of mower should be the same or
within 1/4" of each other.
• If adjustment is necessary, make adjustment on one side of mower only.
• To raise one side of mower, tighten lift
link adjustment nut on that side.
• To lower one side of mower, loosen lift
link adjustment nut on that side.
NOTE:
Each full turn of adjustment nut
will change mower height about 1/8".
• Recheck measurements after adjusting.
Bottom edge
of mower to _

0roood

!_g _

Both Front

nks Should be

ual in Length

Bottom edge of
n3o_er to ground

it "E"

Nut

Suspension Arm

mru

Lift Link
Nut_
Adjustment
Front Links

TO REPLACE
BELT

MOWER

BLADE

DRIVE

2. Measure distance between brake operating arm and nut "A" on brake rod.
3. If distance is other than 1-1/2", loosen
jam nut and turn nut "A" until distance
becomes 1-1/2". Retighten jam nut
against nut "A".
4. Road test tractor for proper stopping
distance as stated above. Readjust
if necessary. If stopping distance is
still greater than five (5) feet in highest
gear, further maintenance is necessary. Replace brake pads or contact a
Sears or other qualified service center.

The mower blade drive belt may be replaced without tools. Park the tractor on
level surface. Engage parking brake.
BELT REMOVAL 1. Remove mower from tractor (See "TO
REMOVE MOWER" in this section of
manual).
2. Work belt off both mandrel pulleys and
idler pulleys.
3. Pull belt away from mower.
BELT INSTALLATION 1. Work belt around both mandrel pulleys
and idler pulleys
2. Make sure belt is in all pulley grooves
and inside all belt guides.
3. Install mower (See "To Install Mower" in
this section of this manual).

With Parking Brake "Engaged"

Mandrel
Idler Pulleys

Arm

TO REPLACE

Park the tractor on level surface. Engage
parking brake. For assistance, there is a
belt installation guide decal on bottom side
of left footrest.

Pulley

TO CHECK AND ADJUST BRAKE
Your tractor is equipped with an adjustable
brake system which is mounted on the
right side of the transaxle.
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted.
TO CHECK BRAKE

BELT REMOVAL 1. Remove mower (See "TO REMOVE
MOWER" in this section of manual).
NOTE: Observe entire motion drive belt
and position of all belt guides and keepers.
2. Remove belt from stationary idler and
clutching idler.
3. Remove belt downward from around
engine pulley.
4. Pull belt slack toward rear of tractor.
Remove belt upwards from transaxle
pulley by deflecting belt keepers.
5. Remove belt from center span keeper
and pull belt away from tractor.
BELT INSTALLATION -

1. Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.
2. Place gear shift lever in neutral (N)
position.
The rear wheels must lock and skid when
you try to manually push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
TO ADJUST

MOTION DRIVE BELT

1. Carefully work new belt down between
transaxle belt keepers and onto the
input pulley.
2. Slide belt into the center span keeper.
3. Pull belt toward front of tractor and roll
around the top groove of engine pulley.
4. Install belt through stationary idler and
clutching idler.

BRAKE

1. Depress clutch/brake pedal all the way
down and engage parking brake.

5. Make sure belt is in all pulley grooves
and inside all belt guides and keepers.
6. Install mower (See "TO INSTALL
MOWER" in this section of manual).

FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in and camber are not
adjustable on your tractor. If damage has
occurred to affect the front wheel toe-in or
camber, contact a Sears or other qualified
service center.
TO REMOVE

Center
.Span
Keeper

Clutchir

Stationaryldler
Transaxle

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT
The transaxle should be in neutral when
the gear shift lever is in neutral (N) (lock
gate) position. The adjustment is preset
at the factory; however, if adjustment is
needed, proceed as follows:
1. Make sure transaxle is in neutral (N).
NOTE: When the tractor rear wheels move
freely, the transaxle is in neutral.
2. Loosen ad ustment bolt in front of the
right rear wheel.
3. Position the gear shift lever in the neutral (N) position.
4. Tighten adjustment bolt securely.
NOTE: If additional clearance is needed
to get to adjustment bolt, move mower
deck height to the lowest position.
Neutral Lock Gate
Gearshift

......

...... ..---'.....

TO ADJUST
MENT

If steering
horizontal
positioned
ing wheel
horizontal.

STEERING

Adjustment Bolt
WHEEL

ALIGN-

wheel crossbars are not
(left to right) when wheels are
straight forward, remove steerand reassemble with crossbars
Tighten securely.

WHEEL

FOR REPAIRS

1. Block up axle securely.
2. Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not
lose).
3. Repair tire and reassemble.
NOTE: On rear wheels only: align
grooves in rear wheel hub and axle. Insert
square key.
4. Replace washers and snap retaining
ring securely in axle groove.
5. Replace axle cover.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, purchase and
use tire sealant from Sears. Tire sealant
also prevents tire dry rot and corrosion.
Washers
Retaining
Ring
Axle
Cover

Square Key ---_._.___
(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY
_,WARNING:
Lead-acid batteries generate explosive gases. Keep sparks, flame
and smoking materials away from batteries. Always wear eye protection when
around batteries.
If your battery is too weak to start the
engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of
this manual).
If "jumper cables" are used for emergency
starting, follow this procedure:
IMPORTANT: Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.
TO ATTACH JUMPER CABLES 1. Connect one end of the RED cable
to the POSITIVE (+) terminal of each
battery(A-B), taking care not to short
24
against tractor chassis.

2. Connect one end of the BLACKcable
to the NEGATIVE(-) terminal (C) of
fully chargedbattery.
3. Connect the other end of the BLACK
cable (D) to good chassisground,
awayfrom fuel tank and battery.
TO REMOVE
ORDER -

CABLES,

REVERSE

BLACK

cable first from chassis

and

then from the fully charged battery.
RED cable last from both batteries.

Terminal
Cover

• Keps
.

Positive
(Red)
Cable
TO REPLACE

,/Nut

Hex
Bolt

Negative (Black)
Cable
HEADLIGHT

BULB

1. Raise hood.
2. Pull bulb holder out of the hole in the
backside of the grill.
3. Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
02614

Weak or Dead
Battery

REPLACING

Loose or damaged wiring may
your tractor to run poorly, stop
prevent it from starting.
• Check wiring. See electrical
diagram in the Repair Parts
TO REPLACE FUSE

Fully Charged
Battery

BATTERY

_WARNING:
Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable first
then RED battery cable and carefully
remove battery from tractor.
3. Install new battery with terminals in
same position as old battery.
4. First connect RED battery cable to
positive (+) terminal with hex bolt and
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
5. Connect BLACK grounding cable to
negative (-) terminal with remaining
hex bolt and keps nut. Tighten securely.

cause
running, or
wiring
section.

Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
TO REMOVE HOOD AND GRILL ASSEMBLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
4. When replacing hood, be sure to reconnect the headlight wire connector.
Hood

Seat
Label

Headlight Wire

Connector

ENGINE
Maintenance, repair, or replacement of the
emission control devices and systems, which
are being done at the customers expense,
may be performed by any non-road engine
repair establishment or individual. Warranty
repairs must be performed by an authorized
engine manufacturer's service outlet.
TO ADJUST
CABLE

THROTTLE

IMPORTANT:
Damage to the needle
valve and the seat in carburetor
may result
if screw is turned in too tight.

PRELIMINARY

SETTING -

1. Air cleaner assembly must be assembled to the carburetor when making
carburetor adjustments.
2. Be sure the throttle control cable is
adjusted properly (see above).
FINAL SETTING -

CONTROL

The throttle control has been preset at the
factory and adjustment should not be necessary. Check adjustment as described
below before loosening cable. If adjustment is necessary, proceed as follows:
1. With engine not running, move throttle
control lever from slow to choke position. Slowly move lever from choke to
fast position.
2. Check that holes "A" in governor
control lever and hole in governor plate
line-up. If holes "A" are not aligned,
loosen clamp screw and move throttle
cable until holes are aligned. Tighten
clamp screw securely.
TO ADJUST CARBURETOR

1. Start engine and allow to warm for five
minutes. Make final adjustments with
engine running and shift/motion control
lever in neutral (N) position.
2. Move throttle control lever to slow position. With finger, rotate and hold throttle
lever against idle speed screw. Turn
idle speed screw to attain 1750 RPM.
3. While still holding throttle lever against
idle speed screw, turn idle mixture
valve full travel clockwise then counterclockwise until engine runs rough.
Turn valve to a point midway between
those two positions. Release throttle
lever.

Governor Control Lever

4. Move throttle control lever from slow
to fast position. If engine hesitates or
dies, turn idle mixture valve out (counterclockwise) 1/8 turn. Repeat test and
continue to adjust, if necessary, until
engine accelerates smoothly.
High speed stop is factory adjusted. Do
not adjust - damage may result.
IMPORTANT: Never tamper with the
engine governor, which is factory set
for proper engine speed. Overspeeding the engine above the factory high
speed setting can be dangerous. If you
think the engine-governed high speed
needs adjusting, contact a Sears or other
qualified service center, which has proper
equipment and experience to make any
necessary adjustments.

Clamp
Screw

ACCELERATION

Governor
, Control Plate

Cable

NOTE: The carburetor on this engine is
low emission. It is equipped with an idle
fuel adjusting needle with a limiter cap,
which allows some adjustment within the
limits allowed by the cap. Do not attempt
to remove the limiter cap. The limiter cap
cannot be removed without breaking the
adjusting needle.
The carburetor has been preset at the
factory and adjustment should not be necessary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load. If the
carburetor does need adjustment, proceed
as follows:
In general, turning idle mixture valve in
(clockwise) decreases the supply of fuel to
the engine giving a leaner fuel/air mixture. Turning the idle mixture valve out
(counterclockwise) increases the supply
of fuel to the engine giving a richer fuel/air
mixture.

TEST -

_Ccl
reeSwPeed-_._-_
J_
Idle Mixture Valve -__
With Limiter

Thr°t_ le

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.
_,CAUTION:
Never store the tractor
with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.

blended fuels (called gasohol or using
ethanol or methanol) can attract moisture
which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel system of an engine while in
storage.
• Empty the fuel tank by starting the engine and letting it run until the fuel lines
and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio
found on stabilizer container. Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the carburetor. Do not empty the gas tank and
carburetor if using fuel stabilizer.
ENGINE OIL

TRACTOR
Remove mower from tractor for winter
storage. When mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire tractor (See "CLEANING"
in the Maintenance section of this
manual).
2. Inspect and replace belts, if necessary
(See belt replacement instructions in
the Service and Adjustments section of
this manual).
3. Lubricate as shown in the Maintenance
section of this manual.
4. Be sure that all nuts, bolts and screws
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
5. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.

Drain oil (with engine warm) and replace
with clean engine oil. (See "ENGINE" in
the Maintenance section of this manual).
CYLINDER(S)
1. Remove spark plug(s).
2. Pour one ounce of oil through spark
plug hole(s) into cylinder(s).
3. Turn ignition key to "START" position
for a few seconds to distribute oil.
4. Replace with new spark plug(s).

BATTERY
• Fully charge the battery for storage.
• After a period of time in storage, battery
may require recharging.
• To help prevent corrosion and power
leakage during long periods of storage,
battery cables should be disconnected
and battery cleaned thoroughly (see "TO
CLEAN BATTERY AND TERMINALS" in
the Maintenance section of this manual).
• After cleaning, leave cables disconnected and place cables where they
cannot come in contact with battery
terminals.
• If battery is removed from tractor for
storage, do not store battery directly on
concrete or damp surfaces.

OTHER
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your tractor indoors
and cover it to give protection from dust
and dirt.
• Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot
breathe which allows condensation to
form and will cause your tractor to rust.
IMPORTANT:
Never cover tractor while
engine and exhaust areas are still warm.

ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
hose, or tank during storage. Also, alcohol

TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Will not start

CAUSE

CORRECTION

1. Out of fuel.
2. Engine not "CHOKED"
properly.
3. Engine flooded.

10. Engine valves out of
adjustment.

1. Fill fuel tank.
2. See "TO START ENGINE"
in Operation section.
3. Wait several minutes
before attempting to start.
4. Replace spark plug.
5. Clean/replace air filter.
6. Replace fuel filter.
7. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter.
8. Check all wiring.
9. See "To Adjust Carburetor"
in Service and Adjustments
section.
10. Contact a Sears or other
qualified service center.

1.
2.
3.
4.
5.

4.
5.
6.
7

Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.

8. Loose or damaged wiring.
9. Carburetor out of adjustment.

Hard to start

Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.

6. Loose or damaged wiring.
7. Carburetor out of adjustment.

8. Engine valves out of
adjustment.
Engine will not
turn over

Engine clicks but
will not start

1. Clutch/brake pedal not
depressed.
2. Attachment clutch is engaged.
3. Weak or dead battery.
4. Blown fuse.
5. Corroded battery terminals.
6. Loose or damaged wiring.
7. Faulty ignition switch.
8. Faulty solenoid or starter.

Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank
with fresh, clean gasoline.
6. Check all wiring.
7. See "To Adjust Carburetor"
in Service and Adjustments
section.
8. Contact a Sears or other
qualified service center.
1. Depress clutch/brake

pedal.

9. Faulty operator presence
switch(es).

Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or
starter.
9. Contact a Sears or other
qualified service center.

1.
2.
3.
4.

Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.

2.
3.
4.
5.
6.
7.
8.

Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or
starter.

TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Loss of power

CAUSE

3ORRECTION

1. Cutting too much grass/too
fast.
Throttle in "CHOKE" position.
3. Build-up of grass, leaves
and trash under mower.
Dirty air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
=

7. Dirty fuel filter.
8. Stale or dirty fuel.
9.

Water in fuel.

10.Spark plug wire loose.
11. Dirty engine air screen/fins.
12. Dirty/clogged muffler.
13. Loose or damaged wiring.
14. Carburetor out of adjustment

15. Engine valves out of
adjustment.
Excessive
vibration

1. Worn, bent or loose blade.
2. Bent blade mandrel.
3. Loose/damaged

Engine continues
to run when
operator leaves
seat with attachment clutch
engaged
Poor cut - uneven

part(s).

1. Faulty operator-safety
presence control system.

Worn, bent or loose blade.
2. Mower deck not level.
3. Buildup of grass, leaves,
and trash under mower.
4. Bent blade mandrel.
5. Clogged mower deck vent
holes from buildup of grass,
leaves, and trash around
mandrels.

1. Raise cutting height/reduce
speed.
2. Adjust throttle control.
3. Clean underside of mower
housing.
4. Clean/replace air filter.
5. Check oil level/change oil.
6. Clean and regap or change
spark plug.
7. Replace fuel filter.
8. Empty fuel tank and refill tank
with fresh, clean gasoline.
9. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter.
10. Connect and tighten spark
plug wire.
11.Clean engine air screen/fins.
12. Clean/replace muffler.
13.Check all wiring.
14. See "To Adjust Carburetor"
in Service and Adjustments
section.
15. Contact a Sears or other
qualified service center.
1. Replace
Tighten
2. Contact
qualified
3. Tighten
Replace

blade.
blade bolt.
a Sears or other
service center.
loose part(s).
damaged parts.

1. Check wiring, switches and
connections. If not corrected
contact Sears or other
qualified service center.

1. Replace blade. Tighten
blade bolt.
2. Level mower deck.
3. Clean underside of mower
housing.
4. Contact a Sears or other
qualified service center.
5. Clean around mandrels to
open vent holes.

TROUBLESHOOTING
CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Mower blades will
not rotate

Poor grass
discharge

CAUSE

CORRECTION

1. Obstruction in clutch
mechanism.
2. Worn/damaged mower drive
belt.
3. Frozen idler pulley.
4. Frozen blade mandrel.

1. Engine speed too slow.
2. Travel speed too fast.
3. Wet grass.
4. Mower deck not level.
5. Low/uneven tire air pressure.
6. Worn, bent or loose blade.
7. Buildup of grass, leaves and
trash under mower.
8. Mower drive belt worn.
9. Blades improperly installed.
10. Improper blades used.
11. Clogged mower deck vent
holes from buildup of grass,
leaves, and trash around
mandrels.

Headlight(s) not
working
(if so equipped)

1.
2.
3.
4.
5.

Battery will not
charge

1. Bad battery cell(s).
2. Poor cable connections.
3. Faulty regulator
(if so equipped).
4. Faulty alternator.

Engine "backfires"
when turning
engine "OFF"

Switch is "OFF".
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.

Engine throttle control not
set at "SLOW" position for
30 seconds before stopping
engine.

1. Remove obstruction.
2. Replace mower drive belt.
3. Replace idler pulley.
4. Contact a Sears or other
qualified service center.
1. Place throttle control in
"FAST" position.
2. Shift to slower speed.
3. Allow grass to dry before
mowing.
4. Level mower deck.
5. Check tires for proper air
pressure.
6. Replace/sharpen blade.
Tighten blade bolt.
7. Clean underside of mower
housing.
8. Replace mower drive belt.
9. Reinstall blades sharp edge
down.
10. Replace with blades listed
in this manual.
11.Clean around mandrels to
open vent holes.

1.
2.
3.
4.
5.

Turn switch "ON".
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.

1. Replace battery.
2. Check/clean
all connections.
3.

Replace

regulator.

4. Replace alternator.
Move throttle control to
"SLOW" position and allow
to idle for 30 seconds before
stopping engine.

TRACTOR

- - MODEL

NUMBER

917.273752

SCHEMATIC

,,I,

RED I Ill

o cK

BATTERY

RED

FUSE
(OPTIONAL)
AMMETER

STARTER
6LACK

WHITE
I

SOLENOID

CLUTCH/BRAKE

(PEDAL

UP)

WHITE

SEAT SWITCH
(NOT OCCUPIED)

IGNITION
SWITCH
I

BLACK

_AT_T,ME_LUTCH_

BLACK

BUCK

GROUNDING
CONNECTOR

(CLUTCH OFF)
A
V

(OPTIONAL)
BLACK

IGNITION
UNIT

SPARK
GAP
LUG

_@
I

LINE

(2 PLUGS ON
TWIN CYL ENGINES)

I
I
I
CHARGING

SYSTEM

OUTPUT

28 VOLTS

3 AMP DO @ 3600 R pM

FUEL SHUT-OFF SOLENOID

AC M_N

(C_A RG_G

RED

UGHTING
SYSTEM OUTPUT
5 AMP AC @ 3800 RpM

DIODE

\ _4 VOLTS

NOTE
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR
SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP. THE LIGHTS
WILL BECOME THEIR BRIGHTEST.

RPM

DISCONNECTED)

(
ORANGE

@ 3800

SYSTEM

ALTERNATOR

AC M_N @ 3800 RpM

(L_GHTS OFF)

BROWN

HEADLIGHTS

NON-REMOVABLE
CONNECTIONS

IGNITION SWITCH
POSITION

CIRCUIT

"MAKE"

OFF
RUN/LIGHT

M+G+A1
B+A1

NONE
A2+L

RUN
START

B+A1
B + S + A1

NONE
NONE

WIRING INSULATED

CLIPS

NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO
PROPERLY SECURE YOUR WIRING,
02363

REMOVABLE
CONNECTIONS

I
i

TRACTOR

- - MODEL NUMBER 917.273752

ELECTRICAL
22

I
I
I
I

I
I
I
I
I
\

?
/
/
!
I
I

/
/

I
I
I

J
/
I
I
I

52'
29

I
I

TRACTOR

- - MODEL

NUMBER

917.273752

ELECTRICAL

KEY PART
NO. NO.

DESCRIPTION

1
2
8
16
21
22
24
25
26
27
28
29
30
33
40
41
42
43
45
52
90

Battery
Bolt Hex Hd 1/4-20 uric x 3/4
Box Battery
Switch, Interlock
Harness Asm Light W/4152j
Bulb Light #1156
Cable Battery 6 Ga. 11" red
Cable Battery 6 Ga. w/16 wire red
Fuse
Nut Keps Hex 1/4-20 unc
Cable Ground 6 Ga. 12" black
Switch Plunger Normal Op Gray
Switch lgn
Key Ign
Harness lgn
Bolt BIk. Fin Hex l/4-2O unc x l/2
Cover Terminal Red
Solenoid
Ammeter Rectangular 6 Amp
Protection Wire Loop
Cover Terminal

163465
74760412
176689
176138
183759
4152J
4799J
146147
175158
73510400
4207J
121305X
175566
140403
179720
71110408
131563
178861
121433X
141940
180449

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR
- - MODEL
CHASSIS AND ENCLOSURES

NUMBER

917.273752

259
/

260
258

212 -28

261

_30

278

2O8

2O9

2O8

2O9
6O

_145
j37

208

2o6

2O9

chassis-Laser -It.stltl

TRACTOR
- - MODEL
CHASSIS AND ENCLOSURES

NUMBER

917.273752

KEY
NO.

PART
NO.

DESCRIPTION

1
2
5
9
10
11
13
14
17
18
26
28
30
31
37
38
39
60
64
74
114
115
142
143
144
145
159
206
207
208
209
211
212
258
259
260
261
278
---

174619
176554
155272
187846X013
STD533710
174996
172105X010
17490608
185682X613
184921
STD541437
184247
188570X613
139976
17490508
175710
174714
72140606
154798
STD541437
158112
17490620
175702
186689
175582
156524
155123X428
170165
17670508
17670608
17000612
145212
184248
184245X599
184246X599
184250X428
184258X428
191611
187801
5479J

Chassis
Drawbar
Bumper Hood/Dash
Dash
Bolt, Carriage 3/8-16 x 3/4
Panel, Dash, LH.
Panel, Dash, R.H.
Screw Thdrol 3/8-16 x 1/2
Hood Assembly
Bumper Hood
Nut
Grille/Lens Asm.
Fend/Ftrest
Bracket, Fender Support
Screw Thdrol 5/16-18 x 1/2
Pivot Bracket Assembly, Rear
Bracket Pivot Laser Lt
Bolt Rdhd Sqnk 3/8-16 unc x 1
Dash Lower STLT
Nut Crownlock 3/8-16 unc
Keeper Belt Rear Lh Stl P930
Screw 3/8-16 x 1-1/4
Plate Reinforcement STLT
Bracket Swaybar Chassis
Bracket Pnt Footrest STLT
Rod Pivot Chassis/Hood
Cupholder Stlt Black
Bolt Shoulder 5/16-18TT
Screw Thdrol 5/16-18 x 1/2 Tytt
ScrewThdrol 3/8-16 x 1/2
Screw Hexwsh Thdr. 3/8-16 x 3/4
Nut Hex Flange Lock
Insert Lens Reflective
Lens RH
Lens LH
Cover Lens
Insert Grille
Screw #10 x 3/4 Single Lead - Hex
Plug Dome Plastic
Plug, Button

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR

- - MODEL

NUMBER

917.273752

GROUND DRIVE

7-89

¢120

116

14_
163

82
18

1t
5

166
156

j4
51

_11

_73

38_

L
77

394

37
3

26 27
drive-fender.stlt

TRACTOR

- - MODEL

NUMBER

917.273752

GROUND DRIVE

KEY
NO.

PART
NO.

DESCRIPTION

146682
123666X
12000028
121520X
17000512
165866
STD561210
105701X
74550412
10040400
74490544
STD541431
STD523710
STD541437
106933X
130804
STD541237
106888X
STD551037
STD561210
175765
71673
169592
STD523107
175578
120183X
STD551062
STD571810
179114
74760648
175556
127783
154407
123205X
72110612
STD541437
STD541431
105710X
105709X
17060620
130801
169691
17120614
8883R

Transaxle (See Breakdown)
Peerless 206-545C
Spring, Return, Brake
Pulley, Transaxle
Ring, Retainer
Strap, Torque
Screw 5/16-18 x 3/4
Rod Shifter Fender STLT
Pin, Cotter
Washer, Shift Plate
Bolt 1/4-28 unf W/Patch Gr. 8
Washer Lock Hvy Helical
Bolt Hex FLGHD 5/16-18 Gr. 5
Nut Lock Hx W/Ins 5/16-18 unc
Bolt Fin Hex 3/8-16 unc x 1 Gr. 5
Nut
Knob
Rod, Brake
Nut
Spring, Brake Rod
Washer
Pin
Rod, Parking Brake
Cap, Parking Brake
Bracket, Transaxle
Bolt
Shaft Assembly, Foot Pedal
Bearing, Nylon
Washer
Roll Pin
Pulley, Composite, Flat
Bolt
Keeper, Belt, Idler
Pulley, Idler, V-Groove, Plastic
Bellcrank Clutch Grnd Dry Stl
Retainer, Belt
Bolt
Nut Crown Lock 3/8-16 unc
Nut Crown Lock 5/16-18 uric
Link, Clutch
Spring, Clutch Return
Screw 3/8-16 x 1-1/4
V-Belt, Ground Drive
Keeper, Belt, Center Span
Screw 3/8-16 x .875
Cover, Pedal

1
2
3
4
5
6
8
10
11
13
14
15
16
18
19
21
22
24
25
26
27
28
29
30
32
34
35
36
37
38
39
41
47
48
49
50
51
52
53
55
56
57
59
61
62

KEY
NO.

PART
NO.

DESCRIPTION

63
64
65
66
69
70
74
75
76
77
78
79
80
81
82
83
84
85
89
96
112
113
116
120
150
151
156
158
159
161
162
163
164
165
166
168
169
170
197
198
202
212

175410
173937
STD551143
154778
142432
134683
137057
121749X
STD581075
123583X
121748X
STD580025
145090
165592
165711
19171216
166231
150360
188310X428
STD624003
19091210
127285X
72140608
7390O6O0
175456
19133210
166002
165589
183900
72140406
73680400
74780416
19091210
165623
17490510
165492
165580
178394
169613
169593
72110614
145212

Pulley, Engine
Bolt, Hex 7/16-20 x 4 Gr. 5-1.5 Thr.
Washer
Keeper, Belt, Engine, Fool Proof
Screw Hex Wsh Hi-Lo 1/4 x 1/2 unc
Guide, Mower Drive Belt, R.H.
Spacer, Axle
Washer 25/32 x 1-1/4 x 16 Ga.
E-Ring
Key, Square 2.0 x .1845/1865
Washer 25/32 x 1-5/8 x 16 Ga.
Key Woodruff
Arm, Shift
Shaft Asm Cross Tapered 650 20
Spring, Torsion
Washer 17/32 x 3/4 x 16 Ga.
Link Transaxle
Nut, Nylock
Console, Shift, STLT
Retainer Spring 1"
Washer 9/32 x 3/4 x 10 Ga.
Strap Torque 90 Degrees
Bolt Rdhd Sqneck 3/8-16 x 1
Nut Lock Fig. 3/8-16 unc
Spacer Retainer
Washer 13/32 x 2 x 10 Ga.
Washer Srrted 5/161D x 1.125
Bracket Shift Mount
Hub Shift
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5
Nut Crownlock 1/4-20 uric
Bolt Hex Fin 1/4-20 unc x 1 Gr. 5
Washer 9/32 x 3/4 x 10 Ga.
Bracket Pivot Lever
Screw 5/16-18 x 5/8 TT Yellow
Bolt Shoulder 5/16-18 x .561
Plate Fastening Lt
Keeper Belt Transaxle Gear
Nyiiner Snap-In 5/8 ID
Washer Nyliner 7/8 ID x .105 Hd
Bolt Carr. SH 3/8-16 x 1-3/4 Gr. 5
Nut Hex Flange Lock

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR
STEERING ASSEMBLY

- - MODEL

NUMBER

917.273752

13
65

43
40
/
15

t5
t0

s eering._pl,lt =47

6
8

TRACTOR
STEERING ASSEMBLY

- - MODEL

NUMBER

917.273752

KEY
NO.

PART
NO.

DESCRIPTION

1
2
3
4
5
6
8
10
11
12
13
15
17
26
28
29
30
32
36
37
38
39
40
41
42
43
44
46
51
54
65
67
68
71
82
87
88
91

184704X428
184706
169840
169839
6266H
121748X
12000029
175121
STD551137
73940800
136518
145212
180641
126847X
19131416
17000612
STD561210
130465
155099
152927
159946X428
19182411
STD541537
159945
145054X428
121749X
180640
184946X505
73540400
71130420
160367
72110618
169827
175146
169835
173966
175118
175553

Steering Wheel
Axle Assembly
Spindle Assembly, LH.
Spindle Assembly, R.H.
Bearing, Race, Thrust, Hardened
Washer 25/32 x 1-5/8 x 16 Ga.
Ring, Klip
Draglink
Washer, Lock
Nut Hex Jam Toplock 1/2-20 unf
Spacer Bearing Axle Front
Nut, Hex Flange Lock
Shaft Assembly, Steering
Bushing, Link, Drag
Washer 13/32 x 7/8 x 16 Ga.
Screw 3/8-16 x 3/4
Pin Cotter
Rod, Tie
Bushing, Steering
Screw
Insert, Steering Wheel
Washer 9/16 x 1-1/2 11
Nut Lock Center 3/8-24 unf
Adaptor, Steering Wheel
Boot, Steering Shaft
Washer 25/32 x 1-1/4 x 16 Ga.
Extension Shaft Steering
Cap, Spindle
Nut Crownlock 1/4-28
Bolt Hex 1/4-28 unf x 1-1/4 Gr. 8
Spacer Brace Axle
Bolt RDHD Sqnk 3/8-16 x 2-1/4
Axle, Brace
Steering Asm.
Bracket Susp. Chassis Front
Washer Flat
Bolt Shoulder 7/16-20 unc
Clip Steering

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR

- - MODEL

NUMBER

917.273752

ENGINE
3
72

33
31
40

\
OPTIONAL

EQUIPMENT

Spark Arrester

KEY PART
NO. NO.
1
2

170545X505
17720408

3
4
13
14
16
23
29
31
32

137352
165291
148456
STD551237
169837
137180
184900
140527

engine-bs.lcy[

KEY PART
NO. NO.

DESCRIPTION
Control, Throttle/Choke
Screw, Hex Head, Thread
Cutting 1/4-20 x 1/2
Engine, B&S Model
31P777-0299-E1 (See Breakdown)
Muffler
Gasket
Tube Drain Oil Easy
Washer
Shield Brn/Dbr Guard
Arrestor, Spark
Tank, Fuel
Cap Assembly, Fuel

33
37
38
40
44

123487X
137040
181654
124028X
17670412

45
46
72
78
81

17000612
19091416
183906
17060620
73510400

DESCRIPTION
Clamp, Hose
Line, Fuel
Plug Drain Oil Easy
Bushing, Snap, Fuel Line
Screw, Hex Washer Head,
Thd., Roll. 1/4-20 x 3/4
Screw Hxwsh Thdr 3/8-16 x 3/4
Washer 9/32 x 7/8 x 16 Ga.
Screw Socket Head 5/16-18 x 1
Screw 3/8-16 x 1-1/4
Nut Keps Hex 1/4-20 uric

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR

- - MODEL

NUMBER

917.273752

LIFT ASSEMBLY
7

13
2

4
6

13
19
20

19
15

KEY
NO.

PART
NO.

159460

2
3
4
5
6
7
8
11
12

159471
105767X
12000002
19211621
120183X
125631X
122365X
139865
139866

f
lift-rh,lpiece_3

DESCRIPTION
Washer Asm Inner Spring
W/Plunger
Shaft Asm. Lift
Pin Groove
E Ring #5133-62
Washer 21/32 x 1 x21 Ga.
Bearing Nylong
Grip Handle Fluted
Button Plunger Read
Link Asm Lift LH.
Link Asm Lift R.H.

KEY
NO.

PART
NO.

DESCRIPTION

13
15
16
17
18
19
20
31
32

STD624008
173288
73350800
175689
73800800
139868
163552
169865
73540600

Retainer Spring
Link Front
Nut Jam Hex 1/2-13 unc
Trunnion BIk Zinc
Nut Lock w/Wsh 1/2-13 uric
Arm Suspension Mower
Retainer Spring
Bearing, Pvt. Lift
Nut Crownlock 3/8-24

NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

TRACTOR

-- MODEL

NUMBER

917.273752

SEAT ASSEMBLY

\
\

21
I /

ill:
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : No
Page Count : 56
Page Layout : SinglePage
Page Mode : UseNone
Producer : Goby Monitor Application version 3, 2, 1, 4
Create Date : Wed Apr 04 11:05:15 2007
Author :
Title :
Subject :

EXIF Metadata provided by EXIF.tools

Craftsman 917273752 User Manual LAWN TRACTOR Manuals And Guides L0404217

CRAFTSMAN Lawn, Tractor Manual L0404217 CRAFTSMAN Lawn, Tractor Owner's Manual, CRAFTSMAN Lawn, Tractor installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation