Craftsman 917380520 User Manual LAWN MOWER Manuals And Guides L0806105

CRAFTSMAN Walk Behind Lawnmower, Gas Manual L0806105 CRAFTSMAN Walk Behind Lawnmower, Gas Owner's Manual, CRAFTSMAN Walk Behind Lawnmower, Gas installation guides

User Manual: Craftsman 917380520 917380520 CRAFTSMAN LAWN MOWER - Manuals and Guides View the owners manual for your CRAFTSMAN LAWN MOWER #917380520. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman LAWN MOWER Manual

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

SEAAR8

i_t__ __

MODEL NUMBER 917.380520

oAssembly
oOperation
oCustomer
Responsibilities
oService
oAdjustments
oRepair Parts
Caution:
Read and Follow
all Safety Rules
and Instructions
Before Operating
This Equipment

IIIIIIIIIIIIIIIIII
I'IIIIIIIIIIIIII
IIII IIII

OWNER'SMANUAL

SAFETY RULES
PLUG TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING
CAUTION: ALWAYS DISCONNECTSPARK PLUGWIRE ANDPLACE WIRE WHERE IT CANNOTCONTACT SPARK

REPA,RS

IMPORTANT

SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY° YOUR UNIT IS EQUIPPED WITH
SUCH CONTROLS, DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROLS UNDER ANY CIRCUMSTANCES.

TRAINING:
"

Read this operator's manual carefully Become familiar with
the controls and know how to operate your mower properly
Learn how to quickly stop mower..

•

Always stop the blade whenever you leave or are not using
your mower, or before crossing driveways, walks, roads, and
any gravel-covered areas

Do not allow children to use your mower Never allow adults
to use mower without proper instructions

•

Never direct discharge of material toward bystanders nor
allow anyone near the mower while you are operating it

Keep the area of operation clear of all persons, especially
small children and pets

•

Use mower only as the manufacturer
scribed in this manual

Before cleaning, inspecting, or repairing your mower, stop
the engine and make absolutely sure the blade and all
moving parts have stopped Then disconnect the spark plug
wire and keep it away from the spark plug to prevent
accidental starting

•

Do not continue to run your mower if you hit a foreign object
Follow the procedure outlined above, then repair any damage before restarting and operating you mower.

•

Do not change the governor settings or overspeed
engine Engine damage or personal injury may result

•

Do not operate your mower if it vibrates abnormally_ Excessive vibration is an indication of damage; stop the engine,
safely check for the cause of vibration and repair as required

intended and as de*

Do not operate mower if it has been dropped or damaged in
any manner. Always have damage repaired before using
your mower.
Do not use accessory attachments that are not recommended
by the manufacturer
Use of such attachments may be
hazardous_
The blade turns when the engine is running.

PREPARATION:
•

Always thoroughly check the area to be mowed and clear it of
all stones, sticks, wires, bones, and other foreign objects
These objects will be thrown by the blade and can cause
severe injury

•

Always wear safety glasses or eye shields when starting and
while using your mower.

•

Dress properly
Do not operate mower when barefoot or
wearing open sandals. Wear only solid shoes with good
traction when mowing.

•

Check fuel tank before starting engine Do not fill gas tank
indoors, when the engine is running orwhen the engine is hot.
Allow the engine to cool for several minutes before filling the
gas tank. Clean ol,f any spilled gasoline before starting the
engine

•

Always make wheel height adjustments before starting your
mower Never attempt to do this while the engine is running.

•

Mow only in daylight or good artificial light.

Do not run the engine indoors.
ous

the

Exhaust fumes are danger-

Never cut grass by pulling the mower towards you Mow
across the face of slopes, never up and down oryou might
lose your footing. Do not mow excessively steep slopes
Use caution when operating the mower on uneven terrain or
when changing directions - maintain good footing.
Never operate your mower without proper guards, plates,
grass catcher or other safety devices in place

MAINTENANCE

OPERATION:

AND STORAGE:

•

Check the blade and the engine mounting bolts often to be
sure they are tightened properly

•

Check atl bolts, nuts and screws at frequent intervals for
proper tightness to be sure mower is in safe working condition.

•

Keep alt safety devices in place and working.

•

To reduce fire hazard, keep the engine free of grass, leaves
or excessive grease and oil

•

Check grass catcher often for deterioration and wear and
replace worn bags Use only repfacement bags that are
recommended by and comply with specifications of the
manufacturer of your mower

•

Keep your eyes and mind on your- mower and the area being
cut.. Do not Iet other interests distract you

•

Do not mow wet or slippery grass Never run while operating
your mower. Always be sure of your footing - keep a firm hold
on the handles and walk..

•

Always keep a sharp blade on your mower.

•

Allow engine to cool before storing in any enclosure.

Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times..

•

Never store mower with fuel in the tank inside a building
where fumes may reach an open flame or an ignition source
such as a hot water heater, space heater, clothes dryer, etc

==H ii i=l=l=l=

LOOK FOR THIS SYMBOL
IT MEANS - ATTENTION!t!

TO POINT
BECOME

OUT IMPORTANT
ALERT!!!
YOUR

H=H,HI,I,,H=H=,I=

SAFETY
PRECAUTIONS.
SAFETY IS INVOLVED.

CONGRATULATIONS
on your purchase of a Sears Lawn
Mower. It has been designed, engineered and manufactured to give you the best possibte dependability and
performance..
Should you experience any problem you cannot easily
remedy, please contact your nearest Sears Authorized
Service Center/Department.
We have competent, welltrained technicians and the proper tools to service or repair
this lawn mower.
Please read and retain this manual The instructions wilt
enable you to assemble and maintain your lawn mower
properly. Always observe the "SAFETY RULES"..
MODEL
NUMBER

917.380520

PRODUCT

SPECIFICATIONS

4ORSEPOWER:

DISPLACEMENT:

11 5CU IN

GASOLINE CAPACITY
AND TYPE:

1.5 QUARTS
UNLEADED REGULAR

OIL TYPE (API-SG):

SAE 30 (ABOVE 32°F)
SAE 5W-30 (below 32°F)

OIL CAPACITY:

20 OZS.

SPARK PLUG:
(GAP: 030")

CHAMPION RJ19q.M
STD361458

VALVE CLEARANCE:

INTAKE:
008"
EXHAUST: 008"

SERIAL
NUMBER

SOLID STATE IGNITION
_,iR GAP:

0125 IN,

DATE OF PURCHASE

BLADE BOLT TORQUE:

35-40 FT LBS

THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A DECAL ATTACHED TO THE REAR OF THE
LAWN MOWER HOUSING
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE..

MAINTENANCE
A Sears Maintenance

CUSTOMER

AGREEMENT
Agreement is available on this product. Contact your nearest Sears store for details..

RESPONSIBILEmES

•

Read and observe the safety rules.

•
•

Follow a regular schedule in maintaining, caring for and using your lawn mower.
Follow the instructions under "Customer Responsibilities" and "Storage" sections of this owner's manual..

LIMITED TWO YEAR WARRANTY

ON CRAFTSMAN

POWER MOWER

For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up
according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any
defect in material or workmanshiF
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from
the date of purchase.
This Warranty does not cover:
o

Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts,
air cleaners and spark plug

Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain
the equipment according to the instructions contained in the owner's manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN POWER MOWER TO THE NEAREST
SEARS SERVICE CENTER/DEPARTMENT
IN THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE
THIS PRODUCT IS IN USE IN THE UNlTED STATES
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state°
SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, tLLINOIS 60179

SAFETYRULES

............................................................
2
PRODUCT SPECIFICATIONS ....................................... 3
CUSTOMER RESPONSIBILITIES ........................ 3,9-11
WARRANTY ...................................................................
3
ASSEMBLY ...................................................................
5
OPERATION ..................................................................
6

MAINTENANCE SCHEDULE ........................................ 9
SERVICE AND ADJUSTMENTS ................................. 12
STORAGE ....................................................................
13
TROUBLESHOOTING .................................................
19
REPAIR PARTS- LAWN MOWER ........................ 14"15
REPAIR PARTS - ENGINE ................................ ,_-..16"18
PARTS ORDERINGtSERVlCE ................ BACK COVER

INDEX
A
Accessories ..........................................5
Adjustments:
Carburetor ....................................
12
Engine Speed .......................... 12
Handle Height ............................ 12
Height of Cut ................................ 7
Air Filter:
Replacement ..............................11
Service ...........................................
11

E
Operation:
Engine:
Engine Control ........................... 7
Grass Catcher ........................... 10
Ai_ Filter ..................................... t 1
Mower .............................................7
Oi! Change ..................................11
Oil Level ...................................... 11
Operator Presence
Control Bar ...................................7
Oil Type .............................................
11
Starting ...........................................8
Stopping .......................................8
Options:
Storage ..................................... 13
Accessories ...................................5
F

Assembly .....................................................
5
Fuel:
Capacity ...................................... 3
Storage ........................................t3
Type ........................................... 7

B
Blade:
Sharpening
Replacement

...................................

R
Repair' Parts:
Engine ....................................16-18
Lawn Mower ....................... 14-15
Responsibilities,

Customer ......3,9-11

............................. !0

C
Controls:
Engine Zone Control .................. 6
Engine Speed Control .................6
Operator Presence
ControJ Bar. ....................................
6
Customer Responsibilities ....................
9
Air Filter ........................................11
Blade Care/Replacement
........ 10
Engine ...........................................
11
Lubrication ................................. 11
Spark Plug ....................................
11
Cutting Levels .................................... 7

H
Handle Adjustment;
Assembly ..................................... 5
Cutting Height ............................ 12
L
Lubrication:
Engine ...................................... 9
Lawn Mower .............................. 9

S
Safety Rules

.........................................

Service and Adjustments ............... 12
Carburetor'. .................................12
Discharge Guard ..........................
12
Engine Speed .......................... 12
Handle .........................................12
Spark Plug ..........................................11
Specifications .................................. 3

Speed Control:
Engine ....................................... 12

Maintenance Agreement ................. 3
Maintenance Schedule .................... 9

Starting the Engine ............................ 8
Stopping the Engine ...........................8

Mowing Tips ..................................... 8

Storage ................................................13

Oil:

Trouble Shooting Chart ................. 19
Engine ..................................... 11
Storage ..................................... t3

W
Warranty ........................................... 3

LAWN

OWER ACCESSORmES

These accessories were available when this lawn mower was produced+ They are also available at most Sears retail outlets
and service centers.. Most Sears stores can also order repair parts for you, when you provide the model number of your lawn
mower. Some of these accessories may not apply to your lawn mower

ENGBNE
i

SPARK

PLUG

MUFFLER

AIR FILTER

GAS CAN

ENGINE OIL

STABILIZER

PERFORMANCE

MULCHER KIT

LAWN MOWER MAINTENANCE
LAWN MOWER
COVER

ASS

Read these instructions and this manual in its entirety
before you attempt to assemble or operate your new lawn
mower, Your new Iawn mower has been assembled at the
factory with the exception of those parts left unassembled
for shipping purposes. All parts such as nuts, washers,
bolts, etc., necessary to complete the assembly have been
placed in the parts bag. To ensure safe and proper
operation of your lawn mower, all parts and hardware you
assemble must be tightened securely. Use the correct
tools as necessary to ensure proper tightness

TO REMOVE
CARTON
•
•
o
,,

LAWN

MOWER

OPERATOR PRESENCE
CONTROLBAR
UPPER HANDLE
LIFT UP

FROM
MOWING

Remove loose parts included with mower+
Cut down two end corners of carton and lay end panel
down flat.
Remove all packing materials except padding between
upper and lower handle and padding holding operator
presence control bar to upper handle..
Roll lawn mower out of carton and check carton
thorougly for additional loose parts.

POSITION

LOWER HANDLE

FIG. 1
Raise handles until lower handle section locks into
place in mowing position..

HOW TO SET UP YOUR LAWN
MOWER

Raise upper handle section into place on lower handle,
remove protective padding and tighten both handle
knobs.

Remove handle padding holding operator presence
control bar to upper handle.

TO UNFOLD

Your lawn mower handle can be adjusted !or your
mowing comfort.
Refer to "Adjust Handle in the
Service and Adjustment section of this manual.

HANDLE

(See Fig. 1)

IMPORTANT:
UNFOLD HANDLE CAREFULLY SO AS
NOT TO PINCH OR DAMAGE CONTROL CABLES

OPERATION
l=

iH=

Hill=

=,H,=====

KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.. Compare the
illustrations with your' lawn mower to familiarize yourself with the location of various controls and adjustrnents. Save this
manual for future reference.

OPERATOR

PRESENCE

CONTROLBAR

ENGINE ZONE
CONTROL CABLE

STARTER HANDLE

HANDLE KNOB

,GASOLINE

FILLER CAP

ENGINE OIL CAP
WITH DIPSTICK

ENGINE SPEED CONTROL

PRIMER

DISCHARGE

WHEEL ADJUSTER

GUARD

(ON EACH WHEEL)

"_
"

HOUSING
i

MEETS CPSC SAFETY

HI=IHHH

REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute
and the U,,S..Consumer Product Safety Commission._ The blade turns when the engine is running.
.................

11 i1 =====,H

PRIMER - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.

OPERATOR PRESENCE CONTROL BAR- must be held
down to the handle to start the engine. Release to stop the
engine,.
ENGINE SPEED CONTROL - located on the side of the
engine which allows you to select either fast ('_) or slow
(,_=_) engine speed.

STARTER HANDLE - used for starting the engine.

HOW TO USE YOUR LAWN MOWER
ENGINE

SPEED

(See Fig. 2)

The engine speed is controlled by a lever located on the
side of the engine.. Fast ('_) position is for starting engine,
normal cutting and better grass bagging.
Slow (,_)
position is for light cutting, trimming and fuet economy.

ENGINE

ENGINE SPEED
CONTROL LEVER

ZONE CONTROL
CAUTION: Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the
risk of blade contact injury. Do not
under any circumstances attempt to
defeat the function of the operator control. The blade turns when the engine is
running.

PRIMER

FIG. 2
LOWER WHEELS
FOR HIGH CUT

RAISE WHEELS
FOR LOW CUT

Your lawn mower"is equipped'with an operator presence control bar which requires the operator to be
positioned behind the lawn mower handle to start and
operate the lawn mower..

TO ADJUST
•

CUTTING

HEIGHT

(See Fig. 3)

Raise wheels for low cut and lower wheels for high cut°
Wheels are set in tow cut for shipping.. Adjust cutting
height to suit your requirements. Medium position is
best for most lawns.1

To change cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your
requirements.
Be sure all wheels are in the same
setting°

BEFORE

STARTING

FIG. 3
GASOLINE FILLER CAP

ENGINE

OIL (See Fig. 4)
Your lawn mower is shipped without oil in the engine_
=
Be sure mower is level and area around oil fill is clean°
o

Remove engine oil cap w/dipstick and fill to the full line
on the dipstick.

Use 20 ozs_ of oil. For type and grade of oil to use, see
ENGINE in Customer Responsibilities section of this
manual.

o
•

Pour oil slowly.. Do not over fill..
Check oil level before each use.. Add oil if needed_ Fill
to full line on dipstick.

To read proper level, tighten engine oil cap each time.

Reinstall engine oil cap and tighten..

After the first two (2) hours of mowing, change the oil,
and every 25 hours thereafter.
You may need to
change the oil more often under dusty, dirty conditions.

GAS (See Fig. 4)
o

Fill gasoline tank with fresh, clean, unleaded gasoline.
DO NOT USE PREMIUM GASOLINE BE CAREFUL
NOT TO OVER FILL TANK

ENGINE OIL CAP
W!DIPSTICK

FIG, 4
WARNING:
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should be emptied before storage of 30 days or longer° Drain the fuel tank, start the
engine and let it run until fue! lines and carburetor are
empty. Use fresh fuel next season. See Storage Instructions for additional information.r
Never use engine or
carburetor cleaner products in fuel tank or permanent
damage may occur_

MOWING

TO START ENGINE
•

To start a cold engine, push primerfive (5) times before
trying to start, Use a firm push. This step is not usually
necessary when starting an engine which has already
run for a few minutes,

Move engine speed control lever to fast (_)

Hold operator presence control bar down to the handle
and pull starter handle quickly, DO NOT allow starter
rope to snap back..

To STOP engine, release operator presence control
bar.

position_

•

Under certain conditions, such as very tall grass, it may
be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the engine
and teaving clumps of grass c{ippings.

For extremely heavy cutting, reduce the width of cut
and raise the rear of the lawn mower housing one (t)
wheel adjuster setting higher than the front for better
discharge of grass

•

For' better grass bagging and most cutting conditions,
the engine speed should be set in the fast ('_) position

For side discharge lawn mowers, cutting in a counterclockwise direction, starting at the outside of the area
to be cut, spreads grass clippings more evenly and
puts less load on the engine. To keep clippings off of
waikways, flower beds, etc., make the first cuts in a
clockwise direction_

•

Pores incloth grass catchers can become filled with dirt
and dust with use and catchers will collect less grass,
To prevent this, regularly hose catcher off with water
and let dry before using

Keep top of engine around starter clear and clean of
grass clippings and chaff. This witl help engine air flow
and extend engine life.

NOTE: in cooler weather it may be necessary to repeat
priming steps. Inwarmerweather
over priming rnaycause
flooding and engine will not start. If you do flood enginewait
a few minutes before attempting to start and DO NOT
repeat priming steps.

TIPS

CUSTOMER

RESPONSIBILmTIES

FILL
1N
DATES

f X"

ASYouCOMPLETE
_.REGULARSERy!CE.....................
,,,.,_.

TES

_.o

Check for Loose Fasteners
_)

(iflean/Inspect
Equipped) Grass Catcher
_Clean Lawn Mower

WE insPect/Clean Drive Wheels
(Self-Propelled Mowers)
R Sharpen/Replace Mower Blade

,v'
e"3

Lubrication Chart
Clean Battery/Recharge
(Electric Start Mowers)
E

Check Engine Oil Leve!

N ,Change ,Engine Oil
G Clean Air Filter
N

Inspect Muffler
Replace Spark Plug

Replace Air Filter Paper Cartridge

_t ,2

1 - Change more often when operating under a heavy toad or in high ambient temperatures
2 - Service more often when operating in dirty or dusty conditions
3 - Replace blades more often when mowing in sandy soil
4 _ Charge 48 hours at end of season

GENERAL

LUBRICATION

RECOMMENDATIONS

CHART

(_) WHEEL
ADJUSTER
(_) ENGINE

The warranty on this lawn mower does not cover items that
have been subjected to operator abuse or negligence To
receive full value from the warranty, operator must maintain
mower as instructed in this manual..

OIL

Some adjustments will need to be made periodically to
properly maintain your unit°
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season°
o

Once a year, replace the spark plug, clean or replace
air filter element and check blade for wear. A new spark
plug and clean/new air filter element assures proper
air4uet mixture and helps your engine run better and
last longer_
FoIIow the maintenance schedule in this manual

BEFORE
o
-

EACH

(_) BRAKE
SPRING
BRACKET
(_

DISCHARGE
GUARD
HINGE PIN

USE

Check engine oil level.
Check for loose fasteners

LUBRICATION
Keep unit well lubricated (See "LUBRICATION

CHART")

HANDLE BRACKET
MOUNTING PiN

SPRAY LUBRICANT

(_)

REFER TO CUSTOMER
SECTION.

RESPONSIBILITIES

"ENGINE"

IMPORTANT:
DO NOT OIL OR GREASE PLASTIC WHEEL
BEARINGS.
VISCOUS
LUBRICANTS
WILL ATTRACT
DUST AND DIRT THAT WILL SHORTEN
THE LIFE OF
THE SELF-LUBRICATING
BEARINGS.
IF YOU FEEL
THEY MUST BE LUBRICATED,
USE ONLY A DRY,
POWERED GRAPHITE
TYPE LUBRICANT
SPARINGLY

LAWN MOWER

BLADE
ADAPTER

Always observe safety rules when performing any maintenance.

CRANK_

KEYWAY

TIRES
=

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.

BLADE

BLADE
\

CARE

For best results, mower' blade must be kept sharp. Replace
bent or damaged blades.
SHAFT

TO REMOVE BLADE (See Fig. 5)
•
Disconnect spark plug wire from spark plug and place
wire where it cannot corne in contact with spark plug.
o Turn lawn mower on its side. Make sure air filter and
carburetor are up..
°

Use a wood block between blade and mower housing
to prevent blade from turning when removing blade
bolt

Protect your hands with gloves and/or wrap blade with
heavy cloth..

Remove blade bolt by turning counter-clockwise.
a 9/16" box or open-end wrench.

Remove blade and attaching
washer and hardened washer)

hardware

HARDENED
WASHER
LOCK WASHER

TRAILING
EDGE

BLADE

ADAPTER

FIG. 5
TO SHARPEN BLADE
Care should be taken to keep the blade balanced. An
unbalanced blade will cause eventual damage to lawn
mower or engine.

Use

The blade can be sharpened with a file or on a grinding
wheel Do not attempt to sharpen while on the mower.

To check blade balance, drive a nail into a beam orwall.
Leave about one inch of the straight nail exposed.
Place center hole of blade over the head of the nail.. If
blade is balanced, it should remain in a horizontal
position.. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.

(bolt, lock

NOTE: Remove the blade adapter and check the key
inside hub of blade adapter, The key must be in good
condition to work properly° Replace adapter if damaged.
TO REPLACE BLADE (See Fig. 5)
Position the blade adapter on the engine crankshafL
Be sure key in adapter and crankshaft keyway are
aligned.

GRASS

Position blade on the blade adapter' aligning the two (2)
holes in the blade with the raised lugs on the adapter.

The grass catcher may be hosed with water, but must
be dry when used..

Be sure the trailing edge of blade (opposite sharp
edge) is up toward the engine.
Install the blade bolt with the lockwasher and hardened
washer into blade adapter and crankshaft,
Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clockwise.

•

Check your grass catcher often for damage or deterio*
ration° Through normal use it will wear.. If catcher
needs replacing, replace only with a manufacturer
approved replacement catcher. Give the lawn mower
model number when ordering.

o
-

CATCHER

(If purchased as an accessory)

o The lecommended tightening torque is 35-40 ft. Ibs
IMPORTANT: BLADE BOLT IS GRADE 8 HEATTREATED
NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced_

ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SG. Select the oil's SAE viscosity grade
according to your expected operating temperature.
SAE V_SCOSITY

GRADES

CONTAINER

"20_

°€ .a0°

"2;°

TEMPERATURE

30_

-_o°

32=

40_

;°

RANGE ANTICIPATED

60 °

_0°

80_

t00_

_o° , 3o°

BEFORE NEXT OIL CHANGE

FIG, 6

NOTE: Although multi-viscosity oils (5W30, 10W30 etc,,)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possibte engine damage from running tow on oil,

COLLAR

Change the oil after the first two hours of operation and
every 25 hours thereafter or at least once a year if the lawn
mower is not used for 25 hours in one year.,

CLIF
TURN
COUNTERCLOCKWISE
TO REMOVE

Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use Tighten oil
plug securely each time you check the oil level,

SLOT
TAB

TO CHANGE ENGINE OIL (See Fig. 6)
AIR FILTER COVER

NOTE: Before tipping lawn mower to drain oil, drain fuel
tank by running engine until fuel tank is empty,,

TURN CLOCKWISE
TO TIGHTEN

FIG. 7

Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with spark plug,

•

Remove engine oil cap; lay aside on a clean surface.

MUFFLER

•

Tip lawn mower on its side and drain oil into a suitable
container. Rock lawn mower back and forth to remove
any oil trapped inside of engine,.

Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.

Wipe off any spilled oil on lawn mower and on side of
engine.

Fill engine with oii. Fill only to the "FULL" line on the
dipstick,. DO NOT OVER FiLL

CLEANING

•

Replace engine oil cap,

•

Reconnect spark plug wire to spark plug,

Clean the underside of your mower after each use,
°
Turn lawn mower on its sider Make sure air filter and
carburetor are up. Clean the underside of your lawn
mower by scraping to remove build-up of grass and
trash.

SPARK

Change your spark plug each year to make your engine
start easierand run better. Set spark plug gap at ,030 inch

AIR FILTER
Your engine will not run properiy and may be damaged by
using a dirty air filter,
Replace the air filter every year, more often if you mow in
very dusty, dirty conditions. Do not wash air filter.
TO CHANGE AIR FILTER (See Fig. 7)
=
•
.
•

Remove the air _ter cover by t urning counterclockwise
to the stop and pull away from collar
Remove filter from inside of cover
Clean the inside of the cover and the collar to remove
any dirt accumulation,
Insert new filter into cover.

Put air filter cover and filter into collar aligning the tab
with the slot.,

•

Push in on cover and turn clockwise to tighten.

PLUG

Clean engine often to keeptrash from accumulating, A
clogged engine runs hotter and shortens engine life.

Keep finished surfaces and wheels free of all gasoline,
oit,etco

We DO NOT recommend using a garden hose to clean
lawn mower unless the electrical system, muffler, air
filter and carburetor are covered to keep water out.
Water in engine can result in shortened engine life,

SERVICE AN

ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
Release control bar and stop engine.
o
Make sure the blade and all moving parts have completely stopped.
•
Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.

LAWN MOWER
REAR

SHIPPING POSITION
MEDIUM LOW

DEFLECTOR

MEDIUM HIGH

The rear deflector, attached between the rear wheels of
your mower, is provided to minimize the possibility that
objects will be thrown out of the discharge opening into the
operator mowing position, If the rear deflector becomes
damaged, it should be replaced

DISCHARGE

GUARD

The discharge guard, attached to the discharge opening of
your lawn mower, is provided to prevent the possibility of
injury resulting from objects being thrown out of the discharge guard opening into the operator mowing position,,
_

CAUTION: Donot runyour lawn mower
without discharge guard or approved
gras s catcher in place.

TO ADJUST

HANDLE

CAUTION:

FIG. 8B

(See Figs. 8 - 10)

Your lawn mower' handle can be raised or lowered for your
mowing comfort
Four (4) positions are available: high,
medium high, medium low and low Handles are shipped
mounted in the medium low position.
= To change from medium low to medium high position,
the upper' and lower handle sections will have to be
turned over (See Fig_ 8B).
o
Remove the cable clips
°
Remove the controls and operator presence control
bar from the upper' handle,.
o
Remove the starter rope guide from the lower handler
°
Remove hairpin cotters
=
Disconnect the lower handle from the handle brackets
(See Fig,, 10),
= Turn the handle over and reassemble the hairpin
cotters that have been removed.
.
Reassemble the starter rope guide
•
Reassemble the controls and the operator presence
control bar to the upper handle,
H

FIG. 8A

LOW

FIG. 9A

FIG. 9B

LOWER HANDLE

The operator presence con-

brake engagement when control bar is
trol bar mustDopivot
to permittheblade/
released.
not freely
overtighten
fasteners holding the controls to the upper handle.
=

To change from medium
upper handle section wilt
Fig° 9A)o
To change from medium
lower handle section will
Fig. 9B).

low to high position only the
have to be turned over (See
low to tow position, only the
have to be turned over (See

ENGINE
ENGINE

SPEED

Yourenginespeed
has been factory set. Donot attemptto
increase engine speed orit may result in personal injury.. If
you believe that engine is running too fast ortoo slow, take
your mower to an authorized service center' for repair and
12
adjustment..

HANDLE
BRACKET

HAIRPIN CLIP

FIG. 10
CARBURETOR
Your carburetor has a non-adjustable fixed main jet for
mixture control If your' engine does not operate properly
due to suspected carburetor problems, take your lawn
mower to an authorized service center fo_ repair and
adjustment.

STORAGE
ENGINE

Immediately prepare your fawn mower for storage at the
end of the season or if the unit will not be used for 30 days
or more.

FUEL SYSTEM
IMPORTANT:
IT IS IMPORTANT TO PREVENT GUM
DEPOSITS FROM FORMING IN ESSENTIAL FUEL
SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER,
FUEL HOSE, OR TANK DURING STORAGE,
ALSO,
EXPERIENCE INDICATES THAT ALCOHOL BLENDED
FUELS (CALLED GASOHOL OR USING ETHANOL OR
METHANOL) CAN ATTRACT MOISTURE WHICH LEADS
TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE
ACIDIC GAS CAN DAMAGE THE FUEL
SYSTEM OF AN ENGINE WHILE IN STORAGE

LAWN MOWER
When lawn mower is to be stored for a period of time, clean
it thoroughly, remove all dirt, grease, leaves, etc. Store in
a clean, dry area
•

Clean entire lawn mower (See "CLEANING" in the
Customer Responsibilities section of this manual).

•

Lubricate as shown in the Customer Responsibilities
section of this manual.

Be sure that all nuts, bolts, screws, and pins are
securetyfastened.
Inspect moving partsfordamage,
breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint surfaces; sand
lightly before painting,

HANDLE

Start the engine and let it run until the fuel lines and
carburetor are empty.

Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur..
Use fresh fuel next season

NOTE:
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the carburetor. Do
not drain the gas tank and carburetor if using fuel stabilizer

Squeeze the bottom ends of the lower handle toward
each other until the lower handle clears the handle
bracket, then move handle forwar&

•

Loosen upper handle mounting bolts enough to allow
upper handle to be folded back°
IMPORTANT:
WHEN FOLDING THE HANDLE FOR
STORAGE OR TRANSPORTATION, BE SURE TO FOLD
THE HANDLE AS SHOWN OR YOU MAY DAMAGE THE
CONTROL CABLES
.

Drain the fuel tank.

(See Fig, 11)

You can fold your lawn mower handle for storage.
°

ENGINE

Drain oil (with engine warm) and replace with clean engine
oil
(See "ENGINE"
in the Customer Responsibilities
section of this manual)..

When setting up your handle from the storage position,
the lower handle wilI automatically lock intothe mowing
position.

CYLINDER
o

Remove spark plug,
Pour one ounce (29 ml) of oil through spark plug hole
into cylinde[.

LOWER HANDLE

SQUEEZE

OIL

TO FOLD

Pull starter handle slowly a few times to distribute oil

Replace with new spark plug..

OTHER
_OUNTING
PIN

HAl
COTTER

Do not store gasotine from one season to another

Replace your gasoline can if your can starts to rust
Rust and/or dirt in your gasoline will cause problems

If possible, store your unit indoors and cover it to give
protection from dust and dirt.

Cover your unit with a suitable protective cover that
does net retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your unit to rust.
IMPORTANT: NEVER COVER MOWER WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.

OPERATOR PRESENCE
OONTROLBAR
UPPER HANDLE
FOLD FORWARD
FORSTORAGE
FOLD BACKWARD

l&
MOWING
POSITION
LOWER HANDLE

FIG. 11

with gasoline in the tank inside a building where fumes may reach an open
flame
or spark.
Allow the engine to
AUTION:
Neverstorethelawnmower
cool before storing in any enclosure.

REPAIR PARTS
CRAFTSMAN
1

22" ROTARY LAWN MOWER

MODEL NO. 917.380520

2
39
\

43
_

\
43
\

,,=&

31-_

REPAIR PARTS
CRAFTSMAN

KEY
NO.

.,,&

1
2
3
4
6
7
8
9
10
11
t2
t3
I4
I5
16
17
I8
19
20
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
37

PART
NO.
86902
133088X479
84676X479
103672X
STD541425
131959
850733X004
750097
130861
74350424
85827
51793
136376
88348
STD512505
750157
128797
87584X004
701971X479
701969X479
751592
750388X479
750386X479
750085X007
84920
850855X004
87877
87589
12000014
87593
87590
750149
750913X004
61651
84921

22" ROTARY LAWN MOWER

MODEL NO. 917.380520

DESCRIPTION

KEY
NO.

PART
NO.

Control Bar
Upper Handle
Lower Handle
Rope Guide
Locknut 1/4-20
Handle Bolt
Up-Stop Bracket
Hex Thread Rolling Screw #10-24 x 3/4
Engine Zone Control Cable
Hex Head Bolt 1/4-20-1-1/2
Cable Clip
Hairpin Cotter
Handle Knob
Flat Washer 3/8
Hex Head Self Tapping Screw 1/4-20 x 1/2
Support Rod
Rear Deflector
Deflector Bracket
Handle Bracket Assembly (Left)
Handle Bracket Assembly (Right)
Locknut 3/8-16
Support Bracket (Left)
Support Bracket (Right)
Wheel Adjuster Bracket
Spacer
Selector Spring
Selector Knob
Torsion Spring
E-Ring
Housing Bracket Assembly
Hinge Rod
Discharge Guard
Axle Arm Assembly (Rear)
Spring Washer (Rear)
Shoulder Bolt 3/8-16

38
39
40
41
42
43
44
45
46
47
48
49
51
53
54
55
56
57
58
59
60
61
64
---

62335
701401
750610X004
800333
57143
83923
77400
74760612
59289
55187
85463
STD541425
850998
700869X479
134027X479
48346
851201X004
851514
850973
851074
850263
851084
141095
141201
141202

Available accessories
71 33072
7_! 33201
7"1 33623
7"1 33500
7"1 33300
711 33316

DESCRIPTION
BelIeville Washer
Wheel & Tire Assembly (Rear)
Axle Arm Assembly
Wheel & Tire Assembly (Front)
Wave Washer
Locknut 3/!8-16
Hubcap
Hex Head Bolt 3/8-16 x 3/4
Flat Washer
Screw 5/! 6-18 x 3/4
Danger Decal
Locknut 1/4_20
Hex Head Thread Rolling Screw 3/8-16 x 1
Front Baffle
Rear Baffle (Not Shown)
Lawn Mower Housing (Inct, Ref. #48, 53, 54)
Engine Washer
Blade Adapter
22" Blade
Washer
Helical Hardened Lockwasher 3/8
Hex Head Machine Screw 3/8-24 x 1/4 Grd. 8
Engine - Craftsman Model No. 143.945004
Owner's Manual (English)
Owner's Manual (Spanish)
not included with lawn mower:
Grass Catcher
Mulcher Kit
Gas Can (2.5 gal,)
Fuel Stabilizer
SAE 30W Oil (20 oz.)
Mower Cover

CRAFTSMAN

4-CYCLE ENGINE

MODEL
NUMBER
143.945004

MODEL _ 8ER_LI
HUMBmSHERE

101

41
43

20"/

f
i

I
I

CRAFTSMAN 4=CYCLE ENGaNE
REF PART
NO. NO.
1
2
6
7

36478
26727
33734
34214A

8
9
12
12B
14
15
16
17
18
19
20
30
40

33735
30200
33886
34695
28277
30589
31383A
31335
650548
36281
32600
35996
36073
36074
36075
36070
36071
36072

43
45
46
48
50
52
69
7O
72
75
80
81
82
83
86
89
90
92
93
100
I01
I03
110
119
120
125
126

36076
36077
36078
20381
30963B
32610A
27241
35992
29914
35261
34311D
36083
27897
30574A
30590A
30591
30588A
650488
611004
611112
650815
650816
34443A
610118
650814
34961
36477
36476
3647t
36472
29314B
29315C

130 6021A
135 35395
150 35991
151 31673
169 27234A
172 32755
174 30200

MODEL
NUMBER
143.945004
REF PART
NO. NO.

DESCRIPTION

178
182
184
185
186
189
!90
!91
192
193
194
195
200

Cylinder (Includes Ref #2 and 20)
Dowel Pin
Breather Element
Breather Assembly (includes
Reference Numbers 6, 8, 9 and 12)
* Breather Gasket
Screw #t0-24 x 9/16
Breather Tube
Breather Tube Elbow
Washer
Governer Rod (Includes Refo #14)
Governor Lever
Governor Lever Clamp
Screw #8-32 x 5/16
Extension Spring
Oil Seal
Crankshaft
Piston, Pin & Ring Set, Std. Size
Piston, Pin & Ring Set, oO10"Over
Piston, Pin & Ring Set, ..020" Over
Piston & Pin Assembly, Std. Size
Piston & Pin Assembly, .010" Over
Piston & Pin Assembly, .020" Over
(Assemblies Include Ref. #43)
Ring Set, Piston, Standard Size
Ring Set, Piston, _.0t0" Oversize
Ring Set, Piston, °020" Oversize
Piston Pin Retaining Ring
Connecting Rod Assy.. (IncL #46)
Connecting Rod Bolt
Valve Lifter
Camshaft (BCR)
Oil Pump Assembly
* Mounting Flange Gasket
Mounting Flange (Inclo #72 thru 83)
Oil Drain Plug
Oil Seal
Governor Shaft
Washer
Governor Gear Assyr(tncludes #81)
Governor Spool
Screw 1/4-20 x 1-1/4
Flywheel Key
Flywheel
Belleville Washer
Flywheel Nut
Solid State Ignition
Spark Plug Cover
Screw, Torx T-15 #10-24 x 1
Ground Wire
* Cylinder Head Gasket
Cylinder Head
Exhaust Valve, Standard Size
Exhaust Valve, 1/32" Oversize
Intake Valve, Standard Size
intake Valve, 1/32" Oversize
(All Valves Include Reference #151)
Screw 5/16-18 x 1-1/2
Resistor Spark Plug (RJ19LM)
Valve Spring
Valve Spring Cap
* Valve Cover Gasket
Valve Cover
Screw 10-24 x 9/16

29752
6201
26756
31384A
34337
650839
35831
35039B
34966
34965
32309
610973
35727

202 36482
203 31342
204 650549
205 650777
207 34336
209 30200
215 32410
223 650451
224 34690A
238 650932
239 34338
241 35797
245 35066
250 35065
260 36420A
261 30200
262 650831
275 36473
275B391020
276 33753
277 650988
277A650795
285 35000
287 650926
290 30705
292 26460
298 28763
300 34369B
301 35355
305 35647
306 34265
307 35499
309 650562
310 35648
313 34080
327 35392
370 36261
370A35167
380 632646
390 590694
400 36481

RPM Settings:

DESCRIPTION
Nut and Lock Washer I/4-28
Screw 1/4-28 x 7/8
* Carburetor To Intake Pipe Gasket
intake Pipe (Includes Ref #224)
Governor Link
Screw 1/4-20 x 3/8
Brake Lever
SEo Brake Bracket (Includes #195)
Brake Control Link
Brake Spring
Retaining Ring
Terminal
Control Bracket (Includes
Reference Numbers 202 thru 205)
Compression Spring
Compression Spring
Screw #5-40 x 7/16
Screw #6-32 x 21/32
Throttle Link
Screw 10-24 x 9/16
Control Knob
Screw 1/4-20 x 1
* Intake Pipe Gasket
Screw #10-32 x 49/64
* Air Cleaner Gasket
Air Cleaner Collar
Air Cleaner Filter
Air Cleaner Cover
Blower Housing
Screw 10-24 x 9/16
Screw 1/4-20 x t/2
Muffler (includes Reference #277)
Spark Arrestor Muffler (Includes
Reference #277A)(Optional)
Locking Plate
Screw 1/4_20 x 2q3/64
Screw 1/4-20 x 2-1/4 (Optional)
Starter Cup
Screw #8_32 x 21/64
Fuel Line
Fuel Line Clamp
Screw #10-32 x 35/64
Fuel Tank (Includes #292 and 301)
Fuel Cap
Oil Fill Tube
* O-Ring
O-Ring
Screw #10-32 x 1/2
Dipstick
Spacer
Starter Plug
Instruction Decal
Instruction Decal
Carburetor (Includes Ref. #184)
Rewind Starter
Gasket Set
(Includes All Items Marked *)
Low: 2450-2750,

High: 2900-3200

NOTE: This engine could have been built with 590686
Starter_ Refer to design of air intake louvers for part
identification.. Individual starter parts do not interchange.
NOTE:

Al! component dimensions given in U.S° inches
I inch = 25.4 mm

CRAFTSMAN 4-CYCLE ENGaNE
CARBURETOR

NO. 632646

MODEL
NUMBER
143.945004
REF PART
NO, NO.

I
!
I

REWIND

STARTER

NO. 590694

632646

1
2
4
5
6
7
16
25
27
28
29
3O

631615
631767
631184
631183
632504
650506
631807
631867
631024
632019
631028
631021

31
35
35A
40
44
48

631022
632694
632647
632503
27110
631027

REF PART
NO. NO.

-1
2
3
4
5
6
7
8
11

590694
590599A
590600
590696
590601
590697
590698
590699
590700
590695

12
13

590535
590701

NOTE:

STARTER

Carburetor, Complete
(Includes #184 of Engine Parts List)
Throttle Shaft and Lever Assembly
Throttle Return Spring
Dust Seal Washer', Throttle
Dust Seal, Throttle
Throttle Shutter
Shutter Screw
Fuel Fitting
Float Bowl
Float Shaft
Float
Float Bowl "O" Ring
Inlet Needle, Seat & Clip
(Includes Reference Number 31)
Spring Clip
Primer Bulb/Retaining Ring
Primer' Bulb Filter
High Speed Bowl Nut
Bowl Nut Washer
Welch Plug, Atmospheric Vent

DESCRIPTION
Recoil Starter, Complete
Spring Pin (Includes Reference #4)
Washer
Retainer
Washer
Brake Spring
Starter Dog
Dog Spring
Pulley & Rewind Spring Assembly
Starter Housing Assembly
(40 Degree Grommet)
Starter Rope (98" Long, 9/64" Dia.)
Starter Handle

_--.5

[}
REWIND

DESCRIPTION

NO. 590686

--1

All component dimensions given in U,.S. inches
1 inch = 25.4 mm

REF PART
NO. NO.

-1
2
3
4
5
6
7
8

590686
590599A
590600
590615
590601
590598
590616
590617
590618A

9
10
11

590619
590620
590687

12
13

590535
590452

DESCRIPTION
Recoil Starter
Spring Pin (Includes Reference #4)
Washer
Retainer
Washer
Brake Spring
Starter Dog
Dog Spring
Pulley Assembly (Includes
Reference Number's 9 and 10)
Rewind Spring
Spring Cover
Starter Housing Assembly
(40 Degree Grommet)
Starter Rope (98" Long, 9/64" Di&)
Starter Handle

NOTE: All component dimensions given in U°S, inches
1 inch = 25..4 mm

n,m n,,=,,

TROUBLESHOOTING
, ,,,

PROBLEM

H ,nu,,,,,,,,,,,,,

,,,,

POINTS

H =,=======,,,1=,

= n ,,u,,,,,,,

CORRECTION

CAUSE
===,,

Does not start

1
2
3
4

Dirty air filter
Out of fuel
Stale fuel
Water in fuel

1
2
3
4

Clean/replace air filter
Flit fuel tank
Drain tank and refill wilh fresh clean fuel
Drain fuel tank and carburetor and refill tank with Iresh

5
6
7
B
9

Spark plug wire is disconnected
Bad spark piug
Loose blade or broken blade adapter
Control bar in released position
Control bar defective

5
6
7
8
9

gasoline
Connect
Replace
Tighten
Depress
Replace

Set in 'Higher Cut" position

2
3
4
5
6

Set in "Higher Cut" position
Ctean/rep}ace air filter
CIean underside of mower housing
Check oil level
Cut at slower walking speed

1
2
3
4

Replace btade Tighten blade boil
Set all wheels at same height
Contact an authorized service center/department
Ciean underside of mower housing

!
2

Replace blade Tighten blade bolt

Depress control bar to upper handle before
putting starter rope
Contact an authorized service center/department
Replace blade adapter
Move lawn mower to cut grass or to hard surface

n n ui=,,,,,,

Loss of power

1
2
3
4
5
6

Rear of lawn mower housing/blade dragging
in heavy grass
Cutting too much grass
Dirty air filter
Buildup of grass, leaves and trash under mower
Too much oil in engine
Walking speed too fast

Worn, bent or loose blade

2
3
4

Wheef heights uneven
Low engine speed
Buildup of grass, leaves, and trash under mower

= HH,H,,

lJuu_J=

Poor cut _ uneven

Excessive

wire to plug
spark plug
blade bolt or replace blade adapter
control bar to handle
control bar

vibration

Starter rope hard to pull

Worn, bent or loose blade

Bent engine crankshaft

Engine flywheel brake is on when control bar is
released
Bent engine crankshaft
Blade adapter broken
Blade dragging in grass

2
3
4

Contact an authorized

service centeddepadment

to start engine

Grass catcher not filling
(if so equipped)

Hard to push

1
2

Cutting height too Iow
Lift on blade worn off

3
4

Catcher not venting air
Low engine speed

1
2

Grass is too high or wf_ee! height is too low
Rear of Iawn mower housingib_ade dragging
in grass
Grass catcher too full
Handle height position not right for you

3
4

1
2
3
4

Raise cutting height
Replace blade
Clean grass catcher
Contact an authorized

1
2

Raise cutting height
Raise rear of _awn mower housing one (t)
setting higher
Emptygrass catcher
Adjust handle height to suit

3
4

service centeddepadment

, W/A/R8
OWNER'S
MANUAL

®
5.0 HORSEPOWER
22" SIDE DISCHARGE
ROTARY LAWN MOWER

Each lawn mower has its own model number.
gine has its own model number..

MODEL NO.
917.380520

Each en-

The model number for your lawn mower' will be found on a
decal attached to the rear of the lawn mower housing.
The model number for your engine will be found on the
blower housing of the engine.
All parts listed herein may be ordered from any Sears,
Roebuck and COr. Service Center/Department and most
Retail Stores..

IF YOU NEED
REPAIR SERVICE
OR PARTS:

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PRODUCT - LAWN MOWER

FOR REPAIR SERVICE, CALL
THIS TOLL FREE NUMBER:

1-800-4-REPAIR
(1-800-473-7247)
FOR REPLACEMENT PARTS
INFORMATION AND
ORDERING, CALL THIS
TOLL FREE NUMBER:

1-800-FON-PART

• MODEL NUMBER - 917.380520
• ENGINE - CRAFTSMAN

- MODEL NO. 143.945004

• PART NUMBER
" PART DESCRIPTION
Your Sears merchandise has added value when you
consider Sears has service units nationwide staffed with
Seats trained technicians_,
professional technicians
specifically trained to insure that we meet our pledge to
you, we service what we sell.

(1-800-366-7278)

141201

08/18/93

Printed in USA

I IIIIIIIIIIII

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 20
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Mon Jul 21 03:44:12 2008
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 917380520 User Manual LAWN MOWER Manuals And Guides L0806105

CRAFTSMAN Walk Behind Lawnmower, Gas Manual L0806105 CRAFTSMAN Walk Behind Lawnmower, Gas Owner's Manual, CRAFTSMAN Walk Behind Lawnmower, Gas installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation