Craftsman C950524312A User Manual DUAL STAGE SNOW BLOWER Manuals And Guides L0511284

CRAFTSMAN Snowthrower, Gas Manual L0511284 CRAFTSMAN Snowthrower, Gas Owner's Manual, CRAFTSMAN Snowthrower, Gas installation guides

User Manual: Craftsman C950524312A C950524312A CRAFTSMAN DUAL STAGE SNOW BLOWER - Manuals and Guides View the owners manual for your CRAFTSMAN DUAL STAGE SNOW BLOWER #C950524312A. Home:Lawn & Garden Parts:Craftsman Parts:Craftsman DUAL STAGE SNOW BLOWER Manual

Open the PDF directly: View PDF .
Page Count: 67

S _ARS

Owners

manual

Model

C950524312A

11.5 H.P, 30 inch

CAUTION:

You must read and

understand this owner's

manual before operating

unit.

Serial No.

DUAL STAG

SNOW BLOWER

401428 SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8 PrintedinU.S.A.

RULES FOR SAFE OPERATION

General Information

Thisinstructionbookiswrittenfora personwithsomemechanicalability.

Ukemostservicebooks,notallthestepsaredescribed.Stepsonhowto

loosenortightenfastenersarestepsanyonecanfollowwithsome

mechanicalability.Readandfollowtheseinstructionsbeforeyouusethe

unit.

Knowyourproduct:Ifyouunderstandtheunitandhowtheunit

operates,youwillgetthebestperformance.Asyoureadthismanual,

comparethe illustrationstotheunit.Leamthe locationandthefunctionof

thecontrols.Tohetppreventanaccident,fellowtheoperafinginstructions

andthesafetyrules.Keepthismanualforfuturereference.

IMPORTANT:Manyunitsarenotassembledandaresoldincartons.Itis

theresponsibilityoftheownertomakesuretheassemblyinstructionsin

thismanualareexactlyfollowed.Otherunitsarepurchasedinan

assembledcondition.Onassembledunits,itistheresponsibilityef the

ownertomakesuretheunitiscorrectlyassembled.Theownermust

carefullychecktheunitaccordingtotheinstrustionsinthismanualbefore

it isfirstused.

,_1_ Thismanualcontainssafetyinformationtomakeyou

awareofthehazardsanddsksassociatedwithsnow

throwers,andhowtoavoidthem. Thesnowthrowerisdesignedand

intendedforremovalofsnow,andshouldnot beusedforanyother

purpose,it isimportantthatyoureadandunderstandthese

instructions,andanyoneoperatingtheequipmentreadand

understandtheseinstructions.

•,_WARNING

Theengineexhaustfromthisproductcontainschemicalsknowntothe

StateofCaliforniatocausecancer,birthdefects,orotherrepmducUve

harm.

Asignalword(DANGER,WARNING,orCAUTION)isusedwiththealert

symboltoindicatethelikelihoodandthe potentialseverityofinjury.In

addition,a hazardsymbolmaybeusedtorepresentthetypeofhazard.

,_ DANGERindicatesahazardwhich,ifnotavoided,willresultin

deathorseriousInjury.

_1= WARNINGindicatesahazardwhich,ifnotavoided,couldresult

indeathorseriousInjury.

_. CAUTIONindicatesa hazardwhich,if notavoided,mightresult

in minoror moderateinjury.

CAUTION,whenusedwithoutthealertsymbolindicatesa

sifuatonthatcouldresultIn damagetothe equipment,

HazardSymbolsend the meanings

ThesesymbolsareusedonyourequipmentanddefinedinYouroperating

manual.Reviewandunderstandthemeanings.Theuseofoneof these

symbolscombinedwithasignalwordwillalertyoutopotentialhazards

andhowtoavoidthem.

,_ Safety Alert -Identifies safety Information about

hazards that can result in personal Injury,

_]]] perator's Manual - Read and understand

before performing any activity or running

equipment.

_RutaUng auger

Fire

Rotating impeller _Explosion

Toxic fumes

li_ Rotating gears

/_ Thrown objects

Shock

HotSu_ace

14._? Keep a safe distancefrom the equlpmenL

_ever reach Into

rotating parts,

:_mt. Shot off engine and

remove spark plug

connector before

pertormlng maintenance

or repair work.

(_ Recommended ear

protection for

extended use.

RULES FOR SAFE OPERATION

OperatingSymbolsand their meanings

These symbolsare usedonyourequipmentenddefinedinyouroperating

manuel. It is importantthat youreviewand understandthe meanings.

Failureto understandthe symbolsmightresultinharmto you.

Oil

_,_ Fuel

On Off

J_ Primerbulb

_\_ Throttle

I+1 Ch.oo

Ch.on

Stop

Slow

Forward

N Neutral

Reverse

(_ Ignition On

(_ Ignition Off

Ignition Key

-_ Pushto engage

electric start

Fast _) Electric

Start

Engage (_ Engine

Start

Traction _) Engine Run

Auger Collector _Engine Off

_/_ Auger Clutch

Drive Clutch _Heated Grips

Engage

_-_ Disengage

Discharge Chute Chute Deflector

LEFT RIGHT UP DOWN

_kDANGER

•NeverattempttodearaugerofdebdsorcloggedsnowwhJeequipmentis

engagedorengineis running.Cloggedorblockedaugersstoreenergy

andcanrotateunexpectedly,EVENWITHENGINEOFf

• Stopengineanddisconnectsparkplugwirewhenperformingmaintenance

onequipment.

•Neverleavetheequipmentunattendedwhileengineisrunning.Nways

disengagetheaugerendtractioncontrols,stopengine,andremovekeys.

•Keepchildren,pets,andothersoutoftheareadudngoperation.Children

areo_enattractedtotheequipment.Beminclfutofallparsonspresent.

•Keepalllooseclothingfarawayfromfrontofsnowthrowerendauger.

Scarves,mittens,danglingdrawstdngslooseclothesandpantscan

qucklybecomecaughtintherotatingdeviceanddismembermentwill

occur."fieuplonghairendremovejewelry.

• Thesnowthrowerisintendedtoremovesnowonly.Donotusefor

purposesotherthenwhatisintended.

•Donotclearsnowacmssthefaceofslopes.Exerciseextremecautionwhen

changingdirectiononslopes.Donotattempttoclearsteepslopes.

•Donotusethesnowthroweronsurfacesabovegroundlevelsuchasreefs

ofresidences,garages,perchesorothersuchstructuresorbuildings.

_DANGER

• Uncloggingthedischargechuteisa hazardousactivity.Cloggedor

blockedaugersstoreenergyendcanrotateunexpectedly.

•Neverplacehandsinorneardischargechute.

•WithengineOFF,waitforall movingpartstoceasemovement,thenwitha

stick,clearthechute.Evenwithengineoff,partsmayrotateend

dismembermentcanoccur.

•Cloggedsnowcanhideotherobstructionsinthechuteandcausedamage

totheequipment,impellerorauger.Takeprecautionswhenrestatingthe

equipmentaltersnowremoval.

RULES FOR SAFE OPERATION

_I=DANGER

• Beawareofyourenvironmentwhileoperatingequipment.Runningover

itemssuchas,gravel,doormats,newspapars,toys,androckshidden

undersnow,canallbethrownfromchuteorjamintheauger.

•Alwaysbeawareofthedirectionthe snowisbeingthrown.Nearby

pedestrians,petsorpropertymaybeharmedbyobjectsbeingthrown.

•Familiarizeyourselfwiththeareayouplantowork.Markoffbeundadasof

walkwaysanddrivewaystopreventpropertydamagefromthrownobjects.

•Takecautionwhensnowthrowinginunfamiliarareas.Stayalertforhidden

hazardsandtraffic.

•Afterstdkinga foreignobject,turnengineOFF,w_ for movingpartsto

ceasemovement,andcheckimmediatelyfordamage.Ifdamaged,repair

beforestartingandoperatingsnowthrower.

•W'dhengineOFF,waitformovingpadsto stopandalwaysusea stickto

cleardischargechute.

•Ifunitvibratesaboormally,turnengineOFRVibrationisgenerallya

warningoftrouble.Seaanauthorizeddealerifnecessaryfor repairs.

•Keephandsandfeetawayfromrataitnggears.

•"fieuplonghairandremovejewelry.

•Donotwearloose-fitting_thing, danglingdrawstringsoritemsthatcould

becomecaught.

,_WARNING

WHEN ADDING FUEL

•TurnengineOFFandletenginecoolatleast2 minutesbeforeremoving

gascap.

•RIIfueltankoutdoorsorinweli-ventilatadarea.

•Donotoverfillfuel tank.

•Keepgasolineawayfromsparks,openflames,pilotlights,heat,andother

k3nitionsources.

•Checkfuellines,tank,cap,andfittingsfrequentlyfor cracksorleaks.

Replaceifnecessary.

WHEN STARTINGENGINE

•Makesuresparkplug,muffler,fuel capandaircleanerareinplace.

•Donotcrankenginewithsparkplugremoved.

•fffuelspills,waituntilit evaporatesbeforestartingengine.

•ifenginefloods,setchoketoOPEN/RUNpostiion,placethrottleinFAST

andcrankunfitenginestarts.

WHEN OPERATINGEQUIPMENT

•Donotchokecarburetorto stopengine.

WHEN TRANSPORTINGEQUIPMENT

•TransportwithfueltankEMPTY.

WHEN STORING GASOLINEOR EQUIPMENT WITH FUELIN TANK

•Storeawayfromfurnaces,stoves,waterheatersorotherap_liancasthat

havepilotlightorotherignitionsourcebecausetheycanignitegasaline

vapors,

•Startandrunengineoutdoors.

• Donotstartorrunengineinenclosedarea,evenifdoomsor

windowsareopen.

WARNING

•Allowmuffler,enginecylinderandfinstocoo_beforetouching.

•Removeaccumulatedcombustiblesfrommufflerareaandcylinder

area.

•Installandmaintaininworkingordera sparkarresterbeforeusing

equipmentonforest-cavered,grass-cavered,brush-cavared

unimprovedland.ThestateofCaliforniarequiresthisSection4442of

theCaliforniaPublicResourcesCede.Otherstatesmayhavesimilar

laws.Federalewsapplyonfederalland.

_I=WARNING

•IfthereisnaturalorLPgasleakageInarea,donotstartengine.

•Donutuseprassodzedstaringfluidsbecausevaporsareflammable.

&WARN,NG

BEFORE PERFORMINGADJUSTMENTSOR REPAIRS

•Disconnectsparkplugwireandkeepitawayfromsparkplug.

WHEN TESTING FOR SPARK

•Useapprovedsparkplugtester.

•Donotcheckfor sparkwithsparkplugremoved.

OWNER'S INFORMATION

DATE PURCHASED:

MODEL NO:

SERIAL NO:

STORE WHERE PURCHASED:

ADDRESS:

CITY: PROVINCE:

TELEPHONE :

_Recordthis information about your unit so that you will

be able to provide it in case of loss or theft.

Horse Power 11.5 HP

Displacement 305 cc

Gasoline Capacity

Oil Capacity (5W30)

Spark Plug: (Gap .030 in.)

Bore

Stroke

Armature Air Gap

IT ire Pressure

*Seeside ofthe tirefor maximuminflation.Do

maximumpressureonthe tire wall.

3quarts (2.8 litre)

28 oz. (0.82 litres)

Champion RC12YC

3.120 in (79 mm)

2.438 in (62 mm)

0.010-0.014in

(0.25-0.36 mm)

notexceed the

MAINTENANCE AGREEMENT

The Craftsman Warranty, plus a Maintenance

Agreement, provide maximum value for Sears

products. Contact your nearest Sears store for de-

tails.

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and

using your snow blower.

Follow the instructions under "Customer Responsibilities"

and "Storage" sections of this owner's manual.

WHEELED SNOW BLOWER

LIMITED TWO (2)YEAR WARRANTY ON CRAFTSMAN SNOW BLOWER

For two (2) years from date of purchase, Sears Canada Inc. will repair or replacefree of charge,at Sears option, parts

which are defective as a result of material or workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on snow blower will be 90 days from date of purchase if usedfor commercialor rental purposes.

THIS WARRANTY DOES NOT COVER:

1. Pre-delivery set-up.

2. Expendable items which becomeworn duringnormaluse, such as belts, sparkplugs,filter,shear pinsas well as dam-

ages to the engine resultingfrom operatingthe snowblower with insufficientoil.

3. Tire replacement or repair caused by puncturesfrom outside objects,such as nails,thorns, stumpsor glass.

4. In home service.

Warranty service is available by returning the Craftsman snow blower to the nearest Sears Service Centre/Department

in Canada. This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutorywarranty and does NOT exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do not allow limitations on how Ion

an implied warranty will last so the above limitations may not apply to you.

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8

TABLE OF CONTENTS

HAZARD SYMBOLS AND THE MEANINGS .......... 2

OPERATING SYMBOLS AND THEIR MEANINGS ..... 3

OWNER'S INFORMATION .......................... 5

ASSEMBLY ....................................... 7

TOOLS REQUIRED FOR ASSEMBLY .............. 7

CONTENTS OF SHIPPING CARTON .............. 7

PARTS BAGS CONTENTS: ....................... 7

UNPACKING .................................... 8

UPPER HANDLE AND CRANK ASSEMBLY ......... 9

CHECK THE CABLES ............................ 9

HOW TO SET THE LENGTH OF THE CABLES ..... 9

SPEED SELECT LEVER ........................ 10

SNOW CHUTE ASSEMBLY ...................... 11

OPERATION ..................................... 12

OPERATING CONTROLS ....................... 12

SNOW BLOWER OPERATION ................... 13

WHEEL LOCK OUT PIN ......................... 14

BEFORE STARTING ENGINE .................... 15

CHECK THE OIL ............................... 15

FILL GAS ...................................... 15

BEFORE STOPPING THE ENGINE ............... 16

TO STOP ENGINE .............................. 16

TO START ENGINE ............................

FROZEN STARTER ............................

HOW TO CLEAR A CLOGGED DISCHARGE CHUTE

HOW TO USE THE CLEAN-OUT TOOL ..........

.16

.18

OPERATING TIPS .............................. 19

SERVICE RECOMMENDATIONS ................... 20

CUSTOMER RESPONSIBILITIES .................. 21

SNOW BLOWER ............................... 21

LUBRICATION AT STORAGE .................... 21

LUBRICATION - EVERY 10 HOURS .............. 21

LUBRICATION - EVERY 25 HOURS .............. 22

ENGINE ....................................... 23

ADJUSTMENT/REPAIR ........................... 24

AUGER HOUSING HEIGHT ADJUSTMENT ....... 24

TO ADJUST SCRAPER BAR ..................... 24

TO ADJUST SKID HEIGHT ...................... 24

HOW TO REMOVE THE SNOW HOOD ........... 25

BELTADJUSTMENT ............................ 26

HOW TO REPLACE THE BELTS ................. 27

BELT GUIDE ADJUSTMENT ..................... 30

HOW TO CHECK AND ADJUST THE CABLES .... 30

AUGER DRIVE CABLE ADJUSTMENT ............ 30

TRACTION DRIVE CABLE ADJUSTMENT ......... 31

HOW TO ADJUST OR REPLACE

THE FRICTION WHEEL ....................... 32

AUGER SHEAR BOLT REPLACEMENT ........... 35

STORAGE ....................................... 36

TROUBLE SHOOTING CHART ..................... 37

REPAIR PARTS .................................. 38

ORDER REPAIR PARTS ........................... 67

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 - Knife

2 - 1/2" wrenches (or adjustable wrenches)

2 - 9/16" wrenches (or adjustable wrenches)

2 - 3/4" wrenches (or adjustable wrenches)

1 - 3/8" wrenches (or adjustable wrenches)

1 - Pair pliers or screw driver (to spread cotter pin)

CONTENTS OF SHIPPING CARTON

1- Snow Blower

1- Container of Fuel Stabilizer (Located in Parts Bag)

1- Snow Chute Assembly

1- Crank Assembly

1- Parts Bag

HOW TO MEASURE SCREW SIZE

LENGTH

_ DIAMETER _b WARNING: Always wear safety glasses or eye

shields while assembling snow blower.

PARTS BAGS CONTENTS:

* 2-1/4-20 x 1.75

2- Shifter Knobs

"2-Spacer *2H-Jx/4n"u20 O

*2 - Wrenches

*Non Assembly parts are found in toolbox located on top of belt cover.

ASSEMBLY

Figure 1 shows the snow blower in the shippingposition.

Figure 2 shows the snow blower completely assembled.

Reference to right and left hand side of the snow blower is

from the operator's position at the handle.

UNPACKING

1. Locate the twotear tabs at the bottomof the carton,

2. Pull the tear tape no more than twelve inches (30.48cm.)

at a time. Re-grasp tape next to the carton and pull

again. Repeat until all the tape is torn off.

3. After the tape has been completely removed from the

carton, remove the carton from the base. Cut all four cor-

ners and fold the sides toward the center for easy dispos-

al.

4. Remove the plastic bag that covers the unit.

5. Locate and remove the parts bag.

NOTE: Set the fuel stabilizer aside until adding

gasoline to the fuel tank. We recommend that fuel

stabilizer is added to the fuel each time that gasoline

is added to the fuel tank.

6. For shipping purposes, the height adjust skids are at-

tached to the pallet. Remove the screw that secures

each height adjust skid to the pallet. (See Figure 2).

Screw

Skid

Auger Drive Traction Drive

Clutch Lever

Traction

Drive Cable

Assembly Crank

Speed J Assembly

Selector

Lever

Auger

Drive

Cable Snow Chute

Deflector

_rHousing

Figure 2

7. Roll the snow blower off the carton by pulling on the lower

handle.

CAUTION: DO NOT back over cables.

8. Remove the packing materialfrom the handleassembly.

9. Cut ties securing the clutch control cables to the lower

handle.

NOTE: If the cables have become disconnected from the

clutch levers, reinstall the cables as shown in Figure 3.

Cable

Traction Drive Lever

Figure 3

ASSEMBLY

UPPER HANDLE AND CRANKASSEMBLY

1. Loosen, but do not remove the screws, flatwashers, lock-

washers and hex nuts inthe upper holes of the lower han-

dle.

2. Remove the fasteners and the crank assembly eyebolt

from the lower holes of the lower handle.

3. Raise upper handle into operating position. Upper han-

dle should be to the outside of the lower handle.

Adaptor Boot!

_Flatwashe_

Eye Bolt

D, Locknut

Fiatwasher

Lockwasher_

NOTE: Make sure the cables are not caught between

the upper and lower handle.

\ Bo_

Flatwasher

Figure 4

4. Install the fasteners and the crank assembly eyebolt that

were removed in step 2. DO NOT tighten until all fasten-

ers are in place.

5. Attach the crank rod to the universal joint assembly with

the hair pin (see Figure 5).

6. Tighten nut on eye bolt. Make sure eye bolt is properly

aligned and the crank can freely rotate.

7. Tighten all handle bolts.

NOTE: Make sure crank does not touch carburetor

cover.

Assembly

Universal Joint Figure 5

CHECKTHECABLES

1. If control cables have become unattached from motor

mount frame, reconnect cables as shown in Figure 6.

2. For cable adjustments, see "How To Check And Adjust

The Cables" in the ADJUSTMENT/REPAIR section.

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. Ifan adjustment is necessary, see "How To Check And

Adjust The Cables" in the Service And Adjustment section. 9

Traction Drive Cable Auger Drive Cable

ASSEMBLY

SPEED SELECT LEVER

1, Cut plastic tie securing speed select lever assembly to

the shifter bracket. (See Figure 7)

2. Remove Iocknut, washer, spring, and the bolt. (See

Figure 9)

3. Position speed selector lever assembly as shown in

Figure 8.

4. Reinstall bolt, spring, washer and Iocknut. (See Figure 9)

5. Tighten Iocknut until 1/8 to 3/16 inch of the bolt threads

protrude past the locknut.

6. Thread the 3/8-16" hex jam nut onto the lever until the

nut reaches the end of the thread. (See Figure 9)

7. Thread the plastic knob as far as possible and ensure

that the knob points forward.

8. Tighten the 3/8-16" hex jam nut against the knob secure-

ly.

9, Move shifterthroughall speedsto ensure proper tension

of the spring. If shifter lever sticks in any of the notches,

loosen Iocknut 1/2 turn at a time until shifter lever moves

more freely.

Shifter Bracke_

Figure7

Control Panel

Figure 8

NOTE: View is trorn rightside of unit standing in operator's position.

Plastic Knob"_,_-'_ 3"8 6" "

(pointed (.J--_// / -1 Hex,Jam Nut

forward) _Shifter Bracket

Control Panel

Lccknut

1/8 to 3/8 inch of

Spring

Figure 9

ASSEMBLY

SNOW CHUTE ASSEMBLY

1. Positionthe snow chute onto the snow chuteflange, Al-

ign the three holes inthe snow chutewith holes in snow

chuteflange. (See Figure 10)

2, Place three 5/16-18 carriage boltsfrom insideof chute

as shown in Figure 10. (hardware is found in partsbag)

3. Place three 5/16-18 flatwashers and three 5/16-18 nuts

on outside of flange.

4. Tighten all carriage bolts securely.

NOTE: DO NOT overtigten carriage bolts.

Chute Extension

Flatwasher

Snow Chute Deflector

Carriage Bolts

"-"'- Flange

Figure 10

CHECK THE TIRES

The tires were over inflatedfor shipment. Check the tire

pressure in the tires. See the sidewall of the tire for the

proper inflation.

IMPORTANT! BEFORE YOU START

OPERATING

Check the fasteners. Make sure all fasteners are

tight.

OOn electric start models, the unit was shipped with

the starter cord plugged into the engine. Before

operating, unplug the starter cord from the engine.

NOTE: This snow blower was shipped WITH OIL in the engine. See "Before Starting Engine" in-

structions In the Operation section of this manual before starting engine. I

OPERATION

Get to know your snow blower and its controls. Be sureyou (or any other operator) have read and understoodthe Operation

Precautions listed on page 2 of this manual.

Primer Button

Choke Gas Tank Auger Drive Traction Drive

Control Clutch Lever Clutch Lever

Traction Ddve

Cable

Crank

Assembly

Safety Key

Deflector

Height

Adjust Skid Figure 11

ENGINE AND SNOW BLOWER OPERATING CONTROLS

The engine operating controls and their functions are as

follows:

Choke Control- Set choke controlto ON CHOKE position

to start a cold engine.

Electric Start Button- Used to start the engine usingthe

120 voltelectric starter.

Prime Button- Used to inject fuel directly into carburetor

manifoldto insurefast starts incool weather.

Safety Key- Must be inserted into ignitionkey slot to start

engine. Pull outto stop. Do notturn safety key.

Starter Handle- Starts the engine manually.

The snow blower operating controls and their functions

are as follows:

Speed Select Lever- Allows the operator to use one of six

(6) forward and two (2) reversespeeds.To shift,move speed

select lever to desired position.

NOTE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe

damage to drive system. 12

Auger Drive Clutch Lever- Used to engage and disengage

the auger and impeller.To engage push down, to disengage

release.

Traction Drive Clutch Lever- Used to propel snow blower

forward or reverse. Push down to engage, release to

disengage.

Snow Chute Deflector- Changes the direction the snow is

blown.

Crank- Used to change direction of the snow discharge.

Turn handle clockwise to turn chute to right. Turn handle

counter clockwise to turn chute to left.

Height Adjust Skid- Used to adjust ground clearance of

auger housing (see To Adjust Skid Height in the

Adjustment/Repairsection of this manual).

Toolbox - Spare shear pins, shear bolt wrenches and

spacers are located intoolbox.

Clean-Out Tool - Use the clean-outtoolto removesnowand

debirs from the discharge chute and the auger housing.

OPERATION

The operation of any snow blower can result in foreign objects being thrown into the eyes,which canresult in severe eye damage. Always wear safety glasses or eye shields before beginning snow blower

Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.

SNOW BLOWER OPERATION

The most effective use of the snowblower willbe established

by experience, taking into consideration the terrain, wind

conditions and building location which will determine the

direction of the discharge chute.

NOTE: Do not blow snow towards a building as hidden

objects could be blown with sufficient force to cause

damage.

1. Start the engine as described in section"To Start Engine"

(see Figure 13).

2. Adjust snowchute deflector. Loosen wingnut on the side

of the snow chute and raise chute deflector for more dis-

tance. Tighten wing nut. (see Figure 12).

,_ WARNING: Read Owner's Manual before oper-

ating machine. This machine can be dangerous

if used carelessly.

Never operate the snow blower without all guards, cov-

ers, and shields In place.

Never direct discharge towards windows or allow by-

standers near machine while engine is running.

Stop the engine whenever leaving the operating posi-

tion.

Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making re-

pairs or adjustments.

When leaving the machine, remove the safety key.

To reduce the risk of fire, keep the machine clean and

free from spilled gas, oil and debris.

Using crank, position the discharge chute to discharge

snow with the wind.

Select proper speed for snow conditions as outlinedbe-

low and set speed select lever to desired position.

NOTE: Always release traction drive clutch lever

before moving speed select lever.

Ground speed is determined by snow conditions. Select

the speed you desire by moving the speed selector into

the appropriate colored area on the control panel.

1-2 Wet, Heavy, Slushy, Extra Deep

Tee Knobs

Figure 12

3Moderate

4-5 Very Ught

6Transport Only

NOTE: When clearing wet, heavy snow, it is

recommended that the ground speed of the unit be

reduced and do not attempt to clear the full width of

the unit.

For additional operating instructions see "Operating

Tips" in this section of the manual.

5. Engage auger drive clutch lever (right hand-Figure 13).

IMPORTANT: Be sure front of unit is clear of

bystanders or obstacles before operating.

Engage tractiondrive clutch lever (lefthand-Figure 13).

As the snow blower starts to move, maintain a firm hold

on the handles and guide the snow blower along the cut-

ting path. Do not attempt to push the snow blower. 13

Traction Ddve Auger Drive

Disengaged_ .._._ ClutchLever is_l_ a

ged

Engaged '_ J Engaged

Figure 13

7. To stop forwardmotion, release traction drive clutch lever

(left hand - Figure 13).

8. To stop auger, release auger drive clutch lever (right

hand - Figure 13).

g. To move the snowblower backwards, move speed select

lever into first or second reverse and engage traction

drive clutch lever (left hand). To stop, release traction

drive clutch lever.

OPERATION

WHEEL LOCK OUT PIN

1. The rightwheel is secured to the axle withaklickpin. This

unit was shipped with this klick pin in the locked position.

(Figure 14).

2. For ease of maneuverability when lighter conditions pre-

vail, remove klick pin from wheel locked position and in-

sen into single wheel drive (unlocked) position

(Figure 15). Make sure that the klick pin is in the single

wheel drive position of the axle only and not through the

locked position.

NOTE: Check tire pressure (24 pounds). See side of tire

for maximum inflation, Do not exceed listed maximum

pressure.

Locked

Position

Figure 14

Single Wheel

Drive Position

(Unlocked)

Figure 15

OPERATION

BEFORE STARTING ENGINE 1.

Check the oil

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil Add oil as needed.

Make sure the unit is level. Use a high quality detergent

oil classified "For Service SG, SH, SJ, SL, or higher".

Remove the oil fill cap/dipstick and wipe with a clean

cloth (see Figure 16).

3. Insert the oilfillcap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil

NOTE: Do not check the level of the oil while the

engine runs.

5. If necessary, add oil until the oil reaches the FULL mark

on the oil fill/capdipstick (see Figure 16). Do not add too

much oil.

6. Tighten the fill cap/dipstick securelyeach time you check

the oil level.

NOTE: For extreme cold operating conditions of 0°F

(-18 ° C) and below, use a synthetic 5W30 motor oil for

easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make

starting easier in areas where the temperature is 20 ° F.

(-7 ° C) to O°F (-18 ° C). Synthetic 5W30 is acceptable for

all temperatures. DO NOT mix oil with gasoline,

NOTE: SEE CHART FOR OIL RECOMMENDATION

TEMPERATURE TYPE OF OIL

0°F (-18 °C) and above S.A.E. 5W30

0°F (-18 ° C) and below synthetic 5W30

Fillthe fuel tank withfresh, clean, unleaded regular, un-

leaded premium, or reformulated automotive gasoline

with a minimum of 85 octane along with a fuel stabilizer

(follow instructions on fuel stabilizer package). DO NOT

use leaded gasoline. We recommend that fuel stabilizer

be added to the fuel each time that gasoline is added to

the fuel tank.

NOTE: Winter grade gasoline has higher volatility to

improve starting. Be certain container is clean and

free from rust or other foreign particles. Never use

gasoline that may be stale from long periods of

storage in the container.

CAUTION: DO NOT use gasoline containing any

amount of alcohol as it can cause sedous damage to

the engine or significantly reduce the performance.

_k ARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline.

Turn engine off and let engine cool at least two

minutes before removing the gas cap. Do not add gaso-

line to the fuel tank while snow blower is running, hot,

or when snow blower is in an enclosed area. Keep away

from open flame, electrical sparks and DO NOT SMOKE

while filling the fuel tank. Never fill the fuel tank com-

pletely; but fill the fuel tank to within 1-1/2 inch (3.8 mm)

from the top to provide space for the expansion of the

fuel. Always fill fuel tank outdoors and use a funnel or

spout to prevent spilling, Make sure to wipe up any

spilled fuel before starting the engine.

Store gasoline in a clean, approved container, and keep

the cap in place on the container. Keep gasoline in a

cool well ventilated place; never in the house. Never

buy more than a 30 day supply of gasoline to assure

volatility. Gasoline Is intended to be used as a fuel for

internal combustion engines; therefore, do not use

gasoline for any other purpose. Since many children

like the smell of gasoline, keep it out of their reach be-

cause the fumes are dangerous to inhale, as well as be-

ing explosive.

SAE VISCOSITY GRADES

=,- WJ JBJ

°F 20 0 20 32 40

I I I • •

•i¶ • •

°C -30 -20 -10 0 10

FILL GAS

This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications) 15

Oil Fill

Cap/Dipstick

Figure 16

OPERATION

BEFORE STOPPING THE ENGINE

Run the engine for a few minutes to help dry off any moisture

on the engine.

TO STOP ENGINE

CAUTION: To stop the engine, do not move the choke

control to CHOKE position. Backfire or engine damage

can occur.

2. Pull out the safety key.

1. Push the stop switch to the OFF position.

Stop Switch

Safety Key

Figure 18

Figure 17

TO START ENGINE

Be sure that engine oil is at FULL mark on the oil fill

cap/dipstick. The snow thrower engine is equipped with a 120

volt A.C. electric starter and recoil starter. Before starting the

engine, be certain that you have read the following

information.

If engine floods, set the choke to the OPEN/RUN position and

crank until the engine starts.

_lb WARNING: Rapid retraction of the starter cord(kickback) will pull your hand or arm toward the

engine faster than you can let go of the starter

cord.

•When starting the engine, slowly pull the starter cord

until resistance is felt. Then rapidly pull the starter

cord.

•Make sure components; such as impellore, pulleys

or sprockets, are securely attached.

_lb WARNING: The electric starter is equipped with

a three-wire power cord and plug designed to

operate on 120 volt AC house hold current. The

power cord must be properly grounded at all times to

avoid the possibility of electric shock which can cause

injury to the operator. Follow all instructions carefully

as set forth below:

Make sure your house has a three-wire grounded sys-

tem. If you ere not sure, ask • licensed electrician. If

your house does not have a three-wire grounded sys-

tem, do not use this electric starter under any condi-

tion.

If your house has a three-wire grounded system but a

three hole receptacle is not available to connect the

electric starter, have a three-hole receptacle installed

by a licensed electrician.

_IL WARNING: To connect a 120 volt power cord,

always connect the power cord first to the

switch box located on the engine and then plug

the other end into a three-hole grounded receptacle.

WARNING: To disconnect the power cord, al-

ways unplug the end connected to the three-

hole grounded receptacle first.

OPERATION

Choke Knob

Primer

Safety Key

Stop Switch Recoil Starter Handle

Starter Motor

Figure 19

How To Start A Cold Engine

1, Be sure auger drive and tractiondrive levers are in the

disengaged (RELEASED) position.

2. Push thestop switch to the ON position (see Figure 19).

3. Push in the safety key.

4. Rotate the choke knob to the CHOKE position.

5. (Electric Start) Plug the power cord intothe starter mo-

tor on the engine. Plug the other end of power cord into

a three-hole, grounded 120 VOLT, AC receptacle.

6. Push the primer button as specifiedbelow. Remove fin-

ger from primer button between pushes.

•Push two times if temperutureis 15° F (-9 ° (3)or high-

er.

• Push four times if temperature is below 15°F (-9 °C).

7, (Electric Start) Connect the power cord to the engine

and depress the starterbutton. To prolongthe lifeof the

starter, do not crankfor more than 5 seconds at atime.

Wait one minute between startsto allowthe startermotor

to cool.

8. (Recoil Start) Slowlypull the recoil starter handle until

resistance isfelt and then pullrepidlyto start the engine.

Do not allow the recoil starter handle to snap back.

Slowly return the recoil starter handle.

9. If the engine does not start in 5or 6 tries, See Difficult

Starting in the 'Troubleshooting Table".

10. Allow the engine to warm up for several minutes. As the

engine warms up, adjust the choke knob toward the

RUN position. Walt untilthe engine runs smoothly before

each choke adjustment.

11. (Electric Start) First disconnect power cordfrom recep-

tacle. Then, disconnectthe power cord from the switch

box.

If after following the preceding instructions,your engine fails

to start, have the engine checked by an Authorized Sears

Service Outlet.

NOTE: Do not lose the safety/ignition key. Keep the

safety/ignition key is a safe place. The engine will not

start without the safety/ignition key.

How To Start A Warm Engine

If restarting a warm engine after a shortshutdown,leave the

choke lever in the off positionand do not push the primer

button. If the engine fails to start, follow the Cold Start

instructions.

OPERATION

FROZEN STARTER

If the starter is frozen and will not turn engine:

1. Pull as much rope out of the starter as possible.

2. Release the starter handle and let it snap back against

the starter. Repeat until the engine starts.

Warm engines will cause condensation in cold weather. To

help prevent possible freeze-up of recoil starter and engine

controls, proceed as follows after each snow removal job.

1. With engine off, allow engine to cool for several minutes.

2. Pull starter rope very slowly until resistance is felt, then

stop. Allow the starter rope to recoil. Repeat three times.

3. With the engine not running, wipe all snow and moisture

from the carburetor cover in area of control levers. Also

move choke knob and starter handle several times.

,_ WARNING: Never run engine indoors or In en-

closed, poorly ventilated areas. Engine exhaust

contains CARBON MONOXIDE, AN ODORLESS

AND DEADLY GAS. Keep hands, feet, hair and loose

clothing away from any moving parts on engine and

snow thrower.

•Engine parts, especially the muffler, become ex-

tremely hot. Severe thermal burns can occur on con-

tact. Allow the engine to cool before touching.

•Never allow children to operate the snow thrower.

Never allow adults to operate the snow blower with-

out proper instruction,

•Keep the area of operation clear of all persons, partic-

ularly small children and pets.

•Never leave the snow blower unattended while the

engine is running. Anyone operating the engine or

equipment must carefully read and understand the

operating instructions.

IMPORTANT: After each use of the snow blower, stop the

engine, remove the safety/ignition key, remove all

accumulated snow from the snow blower and wipe

clean. Store the snow blower in a protected area.

NOTE: Never cover snow blower while engine and

exhaust area are still warm.

HOW TO CLEAR

A CLOGGED DISCHARGE CHUTE

4_b WARNING: Hand contact with the rotating im-

peller inside the discharge chute is the most

common cause of injury associated with snow

blowers. NEVER USE YOUR HAND TO CLEAN OUT

THE DISCHARGE CHUTE.

To Clear The Chute:

•SHUT OFF THE ENGINE!

•Wait 10 seconds to be sure that the impeller blades

have stopped rotating.

•Always use a clean-out tool, not your hands.

A clean-out tool is attached to either the handle or the top of

the auger housing (see Figure 20). Use the clean-out tool to

remove snow from the auger housing.

How To Use The Clean-Out Tool

•Release the auger drive lever.

Pull cut the safety key.

• Disconnect spark plug wire.

Do not place your hands in the auger or discharge

chute. Use a clean-out tool to remove snow or debris.

,a,WARNING: Blockage must be cleared only after

shutting off the snow blower and only with a

clean-out tool, not by hand.

/_ Clean-out Tool

Figure 20

OPERATION

OPERATING TIPS

Most efficient snowblowingis accomplished when snow

is removed immediately after it falls.

For complete snow removal, slightly overlap each swath

previously taken.

Snow should be discharged downwind whenever pos-

sible. 8.

For normal usage, set the skids one-eighth inch (3 mm)

below the scraper bar, For extremely hard-packed snow

surfaces, the skids may be adjusted upward to insure

cleaning efficiency.

On gravel or crushed rock surfaces, the skids should be

set at 1-1/4 inch (32 mm) below the scraper bar (see To

Adjust Skid Height, in the Adjustment/Repair section in

this manual). Rocks and gravel must not be picked up

and thrown by the machine.

After the snowblowingjob has been completed, allow the

engine to idle for a few minutes, to melt snow and ice ac-

cumulated on the engine.

Clean the snow thrower thoroughly after each use.

Remove ice and snow accumulation and all debris from

the entire snow thrower, and flush with water Ofpossible)

to remove all salt or other chemicals. Wipe snow thrower

dry.

10.

Before starting snow blower, always inspectaugers and

impeller for ice accumulation and/or debris, which could

result in snow blower damage.

Check oil level before every start. Make sure the oil is at

the FULL mark on the oil fill cap/dipstick.

SERVICE RECOMMENDATIONS

PROCEDURE FIRST BEFORE EVERY EVERY EVERY EVERY EVERY BEGINNING

2 EACH 8 10 25 50 100 EACH BEFORE

HOUR USE HOURS HOURS HOURS HOURS HOURS SEASON STORAGE

]]ghtenallscrewsand

nuts

Check Traction Clutch

Cable Ad ustment

See Cab eAd ustment)

Check Auger clutch Cable

\d ustment

See Cab e Ad ustment)

Adjust Drive Belts

Lubricate Chains and

Hex Shaft

Lubricate Auger Shaft

See Shear Bolt Replace-

ment)

Oil, Check

Oil, Change

Check and Clean Spark

Plug

iReplace Spark Plug .j

Clean and InspectSpark

Arrestor

The warranty on this snow blower does not cover itemsthat

have been subjected to operator abuse or negligence. To re-

ceive full value from the warranty, operator must maintain

snow blower as instructed inthis manual. The following Ser-

vice Recommendations is supplied to assist operator to

properlymaintain snow blower. This is a check list only. Ad-

justment referred to will be found in Adjustments/Repairs

section of this manual.

Maintenance, replacement, or repair of the emission control

devices and systems can be performed by any non-road en-

gine repair establishment or individual. Regular maintenance

will improve the performance and extend the life of the en-

gine.

AFTER EACH USE

1. Check for any loose or damaged parts.

2. "lighten any loose fasteners.

3. Check and maintain the auger.

4. After each use, remove all snow and slush off the snow

blower to prevent freezing of auger or controls.

5. Check controls to make sure they are functioningproper-

ly.

6. If any parts are worn or damaged, replace immediately.

CUSTOMER RESPONSIBILITIES

Some adjustments will need to be made periodically to

properly maintain your snow blower.

All adjustments in ADJUSTMENTS/REPAIRS section of this

manual should be checked at least once each season.

SNOW BLOWER

The following adjustment should be performed more than

once each season.

Auger and Traction Drive Belts shouldbe adjustedafterthe

first2 to 4 hoursof use, again about mid-season and twice

each season thereafter(See ToAdjustBeltsparagraphinthe

Adjustment/Repairsestion).

AS REQUIRED

Auger Gear Box

The auger gear box is lubricated at the factory and shouldnot

require additional lubrication.

If fQrsome reason the lubricant should leak out, or ifthe auger

gear box has been serviced, add Lubriplate GR132 Grease

or equivalent. Maximum 3-1/4 ounces, (92 grams) should be

used.

Remove filler plug D (Figure 21 and Figure 22), once a year.

If grease is visible, do not add. If grease is not visible, use a

piece of fine wire, like a dipstick to check if there is grease in

the gear box. Mobilux EP1 and Shell Aldania EP1 are

suitable equivalents.

Filler

Plug

Figure 22

LUBRICATION AT STORAGE

Bearings and bushings

All bearings and bushingsare lifetimelubricatedand require

no maintenance.

Hex shaft and chains

For storage, the hex shaftshould be wiped witha cloth lightly

moistened with motor oil to prevent rusting (see Figure 24).

For storage, the chains should be lubricated with a chain type

lube. (see Figure 24).

NOTE: Any greasing or oiling of the above mentioned

components can cause contamination of the rubber

friction wheel. If the disc drive plate or friction wheel

come in contact with grease or oil damage to rubber

friction wheel will result.

If grease or oil comes into contact withthe disc drive plate or

friction wheel, make sure to clean plate and wheel thoroughly

with a alcohol base solvent.

LUBRICATION -EVERY 10 HOURS

1. Auger Shaft -Using ahand grease gun, lubricatethe

auger shaft zerk fittings (A) every ten (10) operating

hours. Each time a shear bolt is replaced, the auger shaft

MUST be greased (Figure 21). (See To Replace Auger

Shear Bolt in the Repair/Adjustment section).

2. For storageor when replacing shear bolts, removeshear

bolts and lubricate auger shaft zerks. Rotate augers sev-

eral times on the shaft and reinstall the shear bolts.

CUSTOMER RESPONSIBILITIES

LUBRICATION - EVERY 25 HOURS

Chute Rotation Gear

Lubricatethe chute rotation gear with automotivetype oil,

(see Figure 23).

Figure 22

Chains

1. Position speed selector lever infirst (1) forward gear.

2. Stand the snow blower up on the auger housing end.

NOTE: When the crank case if filled with oil, do not

leave the snow blower standing up on the auger

housing for an extended period of time,

3. Remove the bottom panel.

4. Lubricate the chains with a chain type lubricant.

5. Wipe the hexshaft and sprockets with5W30 motoroil,

NOTE: Clean all excess grease or oil found on the

rubber friction wheel or the disc drive plate.

CAUTION: Do not allow grease or oil to contact the

rubber friction wheel or the disc drive plate,

6. Installthe bottom panel,

t in

contact with grease or oil

ge to rubber friction wheel

will result,

If grease or oilcome in contact with

the disc drive plate or friction wheel,

make sure to cJeanthe plate and

wheel thoroughlywith a alcohol base

solvent. "!

Figure 24

CUSTOMER RESPONSIBILITIES

ENGINE

POWER RATINGS

The power ratingsfor an individualengine model are initially

developed by starting with SAE (Society of Automotive

Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure) (Revision 2002-05). Given both the wide

array of products on which our engines are placed, and the

variety of environmental issues applicable to operating the

equipment, it may be that the engine you have purchased will

not develop the rated horsepower when used in a piece of

power equipment (actual "on-site" power). This difference is

due to a variety of factors including, but not limited to, the

following: differences in altitude, temperature, barometric

pressure, humidity, fuel, engine lubrication, maximum

governed engine speed, individual engine to engine

variability, design of the particular piece of power equipment,

the manner in which the engine is operated, engine run-in to

reduce friction and clean out of combustion chambers,

adjustments to the valves and carburetor, and other factors.

The power ratings may also be adjusted based on

comparisons to other similar engines utilized in similar

applications, and will therefore not necessarily match the

values derived using the foregoing codes.

Check Crankcase Oil Level before starting engine and after

each 8 hours of continuous use (see Figure 25). Add the

recommended motor oil as required.

NOTE: Overfilling the engine can affect performance.

Tighten the oil fill cap securely to prevent leakage.

TEMPERATURE TYPE OF OIL

0°F (-18 ° C) and above S.A.E. 5W30

0°F (-18 °C) and below synthetic 5W30

SAE VISCOSITY GRADES

°F20 0 20 32 40

II I II s s

i l • l l

°C -30 -20 -10 0 10

Oil Fill Cap/Dipstick _ _ b

F'LL

NOTE: OII level must be at FULL mark. -,uC=*ure

Change Oil every 50 hours of operation or at least once a

year, even ifthe snow blower is notused forfifty hours_ Use

aclean, highqualitydetergentoil. Fillthe crankcase to FULL

line on dipstick(see Figure 25). Be sure originalcontainer is

marked: A.P.I. service"SF" or higher.Do notuse SAE10W40

oil (as it may not provideproper lubrication).See Chart for oil

recommendations.

To Drain Oil - Positionsnow blower so that the oil drain plug

is lowest point on engine. When the engine is warm, remove

oil drain plug and oil fill cap and drain oil into a suitable

container (Figure 26).

Replace oil drain plug and tighten securely. Refill crank case

with the recommended motor oil.

Oil Fillcap/Dipstick

Figure 26

ADJUSTMENT/REPAIR

_lb WARNING: Always turn unit off, remove igni-

tion key and disconnect the spark plug wire be-

fore making any repairs or adjustments.

AUGER HOUSING HEIGHT ADJUSTMENT

TO ADJUST SCRAPER BAR

After considerable use, the metal scraper bar will have a

definite wear pattern. The scraper bar in conjunction with the

skids should always be adjusted to allow one-eighth of an

inch (3 mm) between the scraper bar and the sidewalk or

area to be cleaned.

To adjust the scraper bar, proceed as follows:

1. Position the snow blower on a level surface.

2. Loosen the carriage bolts and nuts securing the scraper

bar to the auger housing.

3. Adjust the scraper bar to the proper position. Tighten the

carriage bolts and nuts, insuring that the scraper bar is

parallel with the working surface.

4. For extended operation, the scraper bar may be re-

versed. If the scraper bar must be replaced because of

wear, remove the carriage bolts and nuts and install a

new scraper bar.

TO ADJUST SKID HEIGHT

This snow blower is equipped with two height adjust skids,

secured to the outside of the auger housing. These elevate

the front of the snow blower.

When removing snow from a hard surface area such as a

paved driveway or walk, adjust the skids up to bring the front

of the snow blower down.

When removing snow from rock or uneven construction,

raise the front of the snow blower by moving the skids down.

This will help to prevent rocks and other debris from being

picked up and thrown by the augers.

To adjust skids, proceed as follows:

1. Place a block (equal to heightfrom grounddesired) un-

der scraper bar near but not under skid.

2. Loosen skid mounting nuts (Figure 27) and push the skid

down until it touches the ground. Retightsn mounting

nuts.

3. Set skid on other side at same height.

NOTE: Make sure that snow blower is sat at same height

on both sides.

,_ WARNING: Be certain to maintain proper

ground clearance for your particular area to be

cleared. Objects such as gravel, rocks or other

debris, if struck by the impeller, may be thrown with

sufficient force to cause personal injury, property dam-

age or damage to the snow blower.

Height Adjust Skid

Skid Mounting Nuts

Figure 27

ADJUSTMENT/REPAIR

HOW TO REMOVE THE SNOW HOOD

To access the spark plug, the snow hood must be removed

as follows:

1. Remove the choke control knob (see Figure 28).

2. Remove the safety key.

3. Remove the mounting screws (see Figure 29).

4. Slowlyremovethe snowhood. Make surethatthe prim-

er button hose and the ignition wire are not discon-

nected.

5. The spark plug can now be accessed.

6. To installthe snow hood, firstmake sure that the primer

buttonhose and the ignitionwire are connected.

7. Mountthe snow hoodto the engine and secure withthe

mountingscrews (see Figure 29).

Mounting Screws

Snow Hood

Spark

Plug

Hose

Figure 29

8. Connect the choke control knobwith the'choke shaft on

the carburetor (see Figure 30 and Figure 31). Make sure

the choke control knob is properly installed, if the choke

control knob is not installed correctly, the choke will not

operate.

9. In_allthe safety key.

Choke Control

Knob

Figure 28

Choke Control Knob

Choke Shaft Figure 30

Carburetor Figure 31

ADJ USTMENT/REPAIR

BELT ADJUSTMENT

Traction Drive Belt

The tractiondrive belt has constant springpressure and does

not require an adjustment. If the traction drive belt is slipping,

replace the belt. See "How To Replace The Belts" in the

Maintenance section.

Auger Drive Belt

If your snowthrower will not discharge snow, check the

control cable adjustment. If it is correct, then check the

condition of the auger drive belt. If it is damaged or loose,

replace it (see Belt Replacement in this section of the

manual),

1. Disconnect spark plug wire.

2. Remove screw from belt cover. Remove belt cover

(see Figure 32).

3. Loosen nut on auger idler pulley and move auger idler

pulley towards belt about 1/8 inch (3 mm) (see

Figure 36).

4. Tighten nut.

5. Have someone engage auger drive clutch. Check ten-

sion on belt (opposite idler pulley). Belt should deflect

about 1/2 inch (12.5 mm) with moderate pressure

Figure 33). You may have to move idler pulley more than

once to obtain the correct tension.

6. Reinstall belt cover.

7. Whenever belts are adjusted or replaced, the cables will

need to be adjusted. (See Cable Adjustment in this sec-

tion of the manual).

8. Attach the spark plug wire.

Auger

Drive

( -_'J_- p_ Engine

k.j; o Po,ey

.....3. ;, \ 1/2 inch

Idler"-"w"V _w_ _'_f" _'A Deflection

Pulley /A/_ ;A

Engaged _

\-÷-/--,m.r

Pulley

Figure 33

ADJUSTM ENT/RI=PAIR

HOW TO REPLACE THE BELTS

The drive belts are of special construction and must be

replaced with original factory replacement belts available

from your nearest authorized service center.

Some steps require the assistance of a second person.

How To Remove the Auger Drive Belt

If the auger drive belt is damaged, the snowthrower will not

discharge snow. Replace the damaged belt as follows.

1. Disconnect the spark plug wire.

2. Loosen the bolts on each side of the bottom panel (see

Figure 34).

3. Remove the bottom panel.

4. Remove screw from belt cover. Remove the belt cover

(see Figure 32).

5. Loosen the belt guide. Pullthe belt guide away from the

auger drive pulley (see Figure 36),

6. Pull the idler pulley away from the auger drive belt and

slip the auger drive belt off of the idler pulley.

7. Remove the auger drive belt from the engine pulley. To

remove the auger drive belt, the engine pulley may

have to be partially rotated,

8. Remove the top four bolts that hold together the auger

housing and the motor box. Loosen the.bottom two

bolts, The auger housing and the motor box can now

be split apart for removal of the belt (see Figure 35).

9. Remove the old auger drive belt from the auger drive

pulley. Replace the auger drive belt with an original

factory replacement belt available from an authorized

service center (see Figure 36).

10. Install the new auger drive belt onto the auger drive

pulley.

NOTE: To assemble the auger housing to the mo-

tor box, have someone hold the auger clutch lever

in the ENGAGED position. This will move the idler

arm and pulley enough to allow the auger drive

pulley to move back into position,

11. Assemble the auger housing to the motor box with the

four bolts that were removed in step 8, Tighten the bot-

tom two bolts.

12. Install the auger drive belt onto the engine pulley.

13. Slip the auger drive belt under the idler pulley.

14. Adjust the auger drive belt. See "How ToAdjust The Au-

ger Drive Belt" in the Maintenance section.

15. Adjust the belt guide. See "How To Adjust The Belt

Guide" inthe Maintenance section, 27

16. Install the belt cover. Tighten screw (See Figure 32).

17. Check the adjustmentofthe cables. See "How To Check

And Adjust The Cables" inthe Maintenance section,

18. Installthe bottom panel (see Figure 34).

19. Tighten the bolts on each side of the bottom panel.

20. Connect the spark plug wire.

Bolt Bottom Panel

Auger Housing

Figure 34

Bolts

Motor Box Auger

Housing

Figure 35

ADJUSTMENT/REPAIR

Belt Guide

Auger Drive Pulley

Auger Drive Belt

Swing Plate Axle Rod

Traction Drive Spring

Traction Drive Belt

Traction Drive Pulley

Engine Pulley

Figure 36

ADJ USTM ENT/R EPAIR

How To Remove the Traction Drive Belt

If the snow throwerwill not move forward, check the traction

drive belt for wear or damage. If the traction drive belt is worn

or damaged, replace the belt as follows.

1. Disconnect the spark plug wire.

2. Remove the auger drive belt. See "How To RemoveThe

Auger Drive Belt" in the Maintenance section.

11. Install and adjust the auger drive belt. See =HowTo Re-

move The Auger Drive Belt"inthe Maintenance section.

12. Adjust the belt guide. See "How To Adjust The Belt

Guide" in the Maintenance section.

13. Install the bottom panel (see Figure 34).

3. Remove the e-ring from one end of the swing plate 14. Tighten the bolts on each side of the bottom panel.

axle rod. Remove the swing plate axle rod to allow the

the swing plate to pivotforward (see Figure 36). 15. Installthe belt cover. Tighten screw (see Figure32),

Remove the traction drive spring.

Remove the old traction drive belt from the traction

drive pulley and from the engine pulley. Replace the

traction drive belt with an originalfactory replacement

belt available from an authorized service center.

16. Check the adjustment of the cables. See "How To Check

And Adjust The Cables" in the Maintenance section.

17. Connect the spark plug wire.

Install the new traction drive belt onto the traction

drive pulley and onto engine pulley.

Make sure the traction drive idler pulley is properly

aligned withthe traction drive belt.

8. Attach the traction drive spring.

9. Installthe swing plate axle rod and secure with the e-

ring removed earlier.

10. The bottom of the swing plate must be positioned be-

tween the alignment tabs. Make sure the swing plate

is properlysecured (see Figure 37).

NOTE: If the drive will not engage after the traction

drive belt has been replaced, then check to make

sure that the swing plate is positioned between the

alignment tabs.

AJignment Tabs Figure 37

ADJUSTMENT/REPAIR

BELT GUIDE ADJUSTMENT

1. Remove spark plug wire.

2. Have someone engage auger drive.

3. Measure the distance between the belt guide and belt.

The distance should be 1/8 inch (3.175 mm) for guide.

See Figure 38.

4, If adjustment is necessary, loosen belt guide mounting

bolt. Move belt guide to the correct position. Tighten

mounting bolt.

5. Reinstall belt cover.

6. Reconnect spark plug wire.

_- -'_O// BeltGuide

Figure 38

HOW TO CHECK AND ADJUST THE CABLES

Tl_e cables are adjusted at the factory and no adjustment

should be necessary, tf the cables have become stretched

or are sagging adjustment will be necessary.

Whenever belts are adjusted or replaced, the cables will

need to be adjusted.

To check for correct adjustment, unhook "Z" fitting at

clutch lever (see Figure 39).

1. Move clutch lever to the full forward position (just con-

tacting plastic bumper). Holding cable tight, note posi-

tion of fitting to hole in clutch lever,

2. The center of the "Z" fitting should be between the centre

and top of the hole in the clutch lever. Adjust either the

auger drive cable or the traction drive cable as follows.

"Z"Fitting Control lever

must be in full

forward position

(just contacting

plastic bumper)

when checking

cable length.

Plastic

Bumper

Figure 39

Auger Drive Cable Adjustment

_k WARNING: Drain the gasoline outdoors, away

from fire or flame.

Remove the gas from the gas tank. Stand the snow

thrower up on the front end of the auger housing.

Push cable through spring to expose the threaded por-

tion of the cable (see Figure 40).

Hold square end of threaded portion with pliers and ad-

just locknutin or out until correct adjustment is reached.

Pull cable back through spring and connect cable. 30

Square

End x,,

Cable

Spring

Locknut

Figure 40

ADJUSTMENT/REPAIR

Traction Drive Cable Adjustment

_lb ARNING: Drain the gasoline outdoors, away

from fire or flame.

1. Remove the gas from the gas tank. Stand the snow

thrower up on the front end of the auger housing.

2. Loosenthe bolts on each side of the bottom panel (see

Figure 41).

3. Remove the bottom panel.

4. Disconnect the "Z" fitting from the drive lever (see

Figure 39),

5. Slide the cable boot off the cable adjustment bracket

(see Figure 42).

6. Push the bottom of the traction drive cable throughthe

cable adjustment bracket untilthe "Z" hook can be re-

moved.

7. Remove the "Z" hook from the cable adjustment

bracket. Move the "Z '° hook down to the next adjust-

ment hole.

8. Pull the traction drive cable up throughthe cable ad-

justment bracket.

9, Putthe cable boot overthe cable adjustment bracket.

10, Install the "Z" hook to the traction drive lever (see

Figure 39).

11. To check the adjustment, depress the drive lever and

check the length of the drive spring (see Figure 43). In

correct adjustment, the length of the drive spring is

minimum 3 inches (76 mm.)

maximum 3-3/8 inches (85 mm.),

12. Install the bottom panel (see Figure 41).

13. "nghtenthe bolts on each side of the bottom panel.

ADJUSTMENT/REPAIR

HOW TO ADJUST OR REPLACE

THE FRICTION WHEEL 5. Tighten the jam nut.

How To Check The Friction Wheel 6. Installthe bottom panel (see Figure 44).

If the snow thrower will not move forward, check the traction

drive belt, the traction drive cable or the friction wheel. If the

friction wheel is worn or damaged, it must be replaced. See

"How To Replace the Friction Wheel" in this section. If the

friction wheel is not worn or damaged, check as follows.

1. Remove the gas from the gas tank. Stand the snow

thrower up on the front end of the auger housing (see

Figure 44).

_Jll= WARNING: Drain the gasoline outdoors, away

from fire or flame.

2. Disconnect the spark plug wire.

3. Loosen the bolts oneach side ofthe bottom panel (see

Figure 44).

4. Remove the bottom panel.

5. Position the shift speed lever in the lowest forward

speed.

6. Note the position of the friction wheel (see Figure 45).

The correct distance "A" from the rightside of the fric-

tion wheel to the outside of the motorbox is as follows:

Tire Size Distance "A"

12 and 13 inch 4-1/8" (10.5 cm.)

16 inch 4-5/16" (10.95 cm.)

If the friction wheel is not inthe correct position,adjust

as follows.

How To Adjust The Friction Wheel

7. Tighten the bolts on each side of the bottom panel,

Bolt

Figure 45

Position the shift speed lever in the lowest forward

speed.

Loosen hex jam nut on speed select rod. Remove ball

joint from shifter bracket (see Figure 46).

Move the friction wheel against to the correct position

(see Figure 45).

Turn the adaptor untilthe ball joint is aligned withthe

mounting hole in the shifter rod (see Figure 46). When

aligned, attach the ball joint to the shifter rod. 32

Rod \

Adap_r

er Rod _1

Figure 46

ADJUSTMENT/REPAIR

How To Replace The Friction Wheel

If the friction wheel isworn or damaged, the snowthrower will

not move forward. The friction wheel must be replaced as

follows.

1. Remove the gas from the gas tank. Stand the snow

thrower up on the front end of the auger housing (4),

(see Figure 44).

_lb ARNING: Drain the gasoline outdoors, away

from fire or flame.

2. Disconnect the spark plug wire.

3. Remove the fasteners that secure the left wheal. Re-

move the left wheel from the axle (see Figure 47)

4. Loosen the bolts on each side of the bottom panel.

5. Remove the bottom panel.

Axle Bort

Panel

Bolt

Wheel Figure 47

6. Remove the fastenersthat secure the drive sprocket to

the axle (see Figure 48).

7. Remove the right wheel, axle, and drive sprocket.

Remove the four bolts that holdthe bearings on each

side of the hex shaft (see Figure 49).

Remove the hex shaft and bearings.

NOTE: Take special note of the position of the

washers on the hex shaft.

_dJ

ADJUSTMENT/REPAIR

10. Remove the three fasteners that holdthe friction wheel

to the hub (see Figure 50).

11. Remove the friction wheel from the hub. Slip the fric-

tion wheel off the hex shaft.

12. Assemble the new friction wheel onto hub withthe fas-

teners removed earlier.

Fasteners Friction

Hub Wheel

Hex Shaft

Fasteners

Figure 50

15.

16.

17.

Washer

_.,._ Washer

Figure 51

Installthe right wheel, axle, and drive sprocket withthe

fasteners removed earlier. Install the chain onto the

drive sprocket (see Figure 48).

Check the adjustment of the friction wheel. See "How To

Adjust The Friction Wheel" in this section.

Make sure the friction wheel and the disc drive plate are

free from grease or oil.

13. Install the hex shaft and bearings with the four bolts re-

moved earlier (see Figure 51).

Make sure the washers are properly installed in the

original position. Also, make sure the two washers

are properly aligned with the actuator arms.

18. Install the bottom panel (see Figure 47).

19. _ghtan the bolts on each side of the bottom panel.

20. Installthe left wheel to the axle with the fasteners re-

moved earlier.

14. Make sure the hex shaft turns freely. 21. Connect the spark plug wire.

ADJUSTMENT/REPAIR

AUGER SHEAR BOLT REPLACEMENT

The augers are secured to the auger shaftwith special bolts

that are designed to break if an object becomes lodged in the

auger housing. Use of a harderbolt will reduce the protection

provided by the shear bolt. To replace a broken shear bolt,

proceed as follows:

NOTE: For the operator's convlence, the shear bolt

wrenches are located in the toolbox.

NOTE: The spacer fits into the larger hole in the auger

tube.

_lb WARNING: To insure safety and performance

levels, only original replacement shear bolts

should be used.

1. Stop engine, disengage all controls, disconnect the

spark plug lead wire, and insure all moving parts have

stopped.

2. Lubricate the auger shaft zerk fittings (see Lubrication

Points in the Maintenance section of this manual).

3, Align the hole in the auger with the hole in the auger shaft.

Install new shear bolt, spacer and Iocknut found in the

toolbox located on the belt cover (See Figure 52). "l]ght-

en with the shear bolt wrench.

Shear Bolt Wrench

Shear Pin _

LF _Spacer

Locknut Figure 52

SPARK PLUG ADJUSTMENT (SEE FIGURE 53)

NOTICE: This spark ignition system meets all 6.

requirements of the Canadian Interference-Causing

Equipment Regulations. 7.

Check the spark plug every twenty-five (25) hours. Replace

the spark plug if the electrodes are pitted or burned, if the

porcelain is cracked, or every 100 hoursof use.

1. Clean spark plug and reset gap periodically.

2. Clean area around spark plug base before removal, to

prevent dirt from entering engine.

3. Replace spark plug if electrodes are pitted or burned or

if porcelain is cracked.

Clean sparkplug by carefully scrapingelectrodes (do not

sandblast or use wire brush).

Be sure spark plug is clean and free of foreign material.

Check electrodes gap with a wire feeler gauge and reset

gap to 0.030" (0.76 mm) if necessary. Ifa new spark plug

is needed, refer to Engine Repair Parts section of this

manual for proper replacement spark plug. 35

Before installing spark plug, coat threads lightly with

graphite grease to insure easy removal.

"nghten plug firmly into engine. If torque wrench is avail-

able, torque plug to 18-23 ft-lbs.

Figure 53

STORAGE

OFF SEASON STORAGE

_lb ARNING: Never store engine with fuel in tank

indoors or in enclosed, poorly ventilated enclo-

sures, where fuel fumes may reach an open

flame, spark or pilot light as on a furnace, water heater,

clothes dryer, etc.

Handle gasoline carefully. It is highly flammable and

careless use could result In serious fire damage to your

person and/or property.

Drain fuel into approved containers outdoors, away

from open flame.

If the snow blower is to be stored for thirty (30) days or more

at the end of the snow season, the following steps are

recommended to prepare your snow blower for storage.

NOTE: Gasoline must be removed or treated to prevent

gum deposits from forming in the tank, filter, hose, and

carburetor during storage.

1, To remove gasoline, run engine until tank is empty and

engine stops.Then drain remaining gasoline from carbu-

retor by pressing upward on bowl drain located on the

bottom of carburetor (see Figure 54).

4_lb WARNING" Drain gasoline outdoors, away fromfire or flame.

4. Thoroughly clean the snow blower.

5. Lubricate all lubricationpoints (see Lubrication, see Cus-

tomer Responsibilities).

5. Insure that all nuts, bolts, and screws are securely fas-

tened. Inspect all visible moving parts for damage,

breakage, and wear. Replace if necessary.

7. Touch up all rusted or chipped paint surfaces; sand lightly

before painting.

8. Cover the bare metal parts of the blower housing auger,

and the impeller with rust preventative.

9. If possible, store your snow blower indoors and cover it

to give protection from dust and dirt.

10. Store in a clean and dry area, but NOT near a stove, fur-

nace or water heater which uses a pilot light or any device

that can create a spark.

11. If the machine must be stored outdoors, block up the

snow blower and insure the entire machine is off the

ground. Cover the snow blower with a heavy tarpaulin.

If you do not want to remove gasoline use the fuel stabilizer

supplied with unit. Add fuel stabilizer (follow instructions on

fuel stabilizer package) to any gasoline left in the tank to

minimize gum deposits and acids. If the tank is almost empty,

mix stabilizer with fresh gasoline in a separate container and

add some to the tank. ALWAYS FOLLOW INSTRUCTIONS

ON STABILIZER CONTAINER. THEN RUN ENGINE AT

LEAST 10 MINUTES AFTER STABILIZER IS ADDED TO

ALLOW MIXTURE TO REACH CARBURETOR. STORE

SNOW BLOWER IN SAFE PLACE.

2. You can help keep your engine in good operating condi-

tion by changing oil before storage.

3. Remove the spark plugand pour about 15 ml (1/2 oz) of

engine oil into the cylinder. Replace the spark plug and

crank slowly to distribute the oil.

Bowl Drain

Figure 54

TROUBLE SHOOTING CHART

PROBLEM LOOK FOR REMEDY

Difficult starting Defective spark plug. Replace defectivespark ptug.

Engine runs erratically Blocked fuel line. Clean fuel line.

Empty gas tank. Check fuel supply,

Stale gasoline. Add fresh gasoline withfuel stabilizer.

Water or dirt in fuel system. Remove carburetorbowlto drainfuel tank. Refill

withfresh fuel. CAUTION: Do not remove

carburetor bowl when the engine is hot.

'Engine stalls Unit running on CHOKE. Set choke leverto RUN position.

Loss of power Gas cap vent hole is plugged. Remove ice and snowfrom cap. Be surevent

hole is clear.

Excessive vibration Loose parts or damaged impeller, Stop engine immediatelyand remove spark plug

wire. Tighten all bolts and make all necessary

repairs. If vibration continues, have the unit

serviced by a competent repairman.

Unit fails to propel Drive belt loose or damaged. Replace drive belt. Refer to Drive Belt

itself Replacement inAdjustments/Repairs section of

this manual.

Incorrect adjustmentof tractiondrive Adjust tractiondrive cable. Refer to Cable

cable. Adjustment inAdjustments/Repairs section of

this manual.

Worn or damaged frictiondisc. Replace friction disc. Refer to Friction Wheel

Replacement inAdjustments/Repairs section of

this manual.

Unit fails to discharge Auger drive belt loose or damaged. Replace or adjust auger drive belt, Refer to Drive

snow Belt Replacement and Drive Belt Adjustment in

Adjuetments/Repairs section of this manual,

Auger controlcable notadjusted Adjust auger controlcable. Refer to Cable

correctly. Adjustment inAdjustments/Repairs section of

this manual.

Broken shear bolt. Replace shear bolt. Refer to Auger Shear Bolt

Replacement inAdjustments/Repairs section of

this manual.

Discharge chuteclogged. Stop engine immediatelyand disconnect spark

plugwire. Refer to the first Warning in Snow

blower Operation in Operation sectionof this

manual. Clean discharge chuteand inside of

auger housing.

Foreign object lodged in auger. Stop engine immediatelyand disconnect spark

plug wire. Refer to the third Warning in Snow

blower Operation in Operation sectionof this

manual. Remove object from auger.

Identifying Your Snow blower

Your new Snow blower has two (2) identifying numbers: (1) unit model number: (2) unit serial number. The two preceding

numbers are required to insure that the proper replacement parts are obtained when required, if you have any questions

concerning parts, service, or technical data, contact your nearest Sears Service Department.

For complete warranty information refer to the warranty in the Owner's Information section of this manual.

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDE RECHANGE

ENGINE /MOTEUR

25-2

25-3

25-1

25-4

20/ 22

24 14 J

/15

/11

Ref. Drive Page

Ref. Auger Housing Page

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

ENGINE /MOTEUR

Key No.

NO8ur le Part No,

sch6ma N° de piTce Description Description

16219 CORD, STARTER CORDE DU DEMARREUR

2 ..... ENGINE MOTEUR

3 002x97 BOLT, CARRIAGE 5/16-18 BOULON, PO. 5/16-18

4 028x76 RETAINER, PUSH RONDELLE DE RETENUE

5 710026 NUT 5/16-18 ECROU 5/16-18

6 1501109 PULLEY, ENGINE POULIE MOTRICE DOUBLE

7 17x170 WASHER RONDELLE

8 71063 WASHER RONDELLE-FREIN DI .38

9001x2O SCREW, 3/8-24Xl.00 VIS, 3/8-24XI.00

10 579932 BELT, V 3L COURROIE TRAPEZOID. V 3L

11 585415 BELT, V 4L COURROIE TRAPEZOID. V 4L

12 1501112 YZ BRACKET ASSEMBLY, IDLER PATFE DE FIXATION, POULIB LIBRE

13 1501065 BUSHING, IDLER BRACKET ENTRETOISE, FIXATION DE POULIE LISRE

14 71060 WASHER RONDELLE

15 710097 SCREW5/16-24XO.75 V[S 5/18-24 X 0.75

16 53704 SPRING RESSORT

17 1502120 PULLEY, IDLER PULLIE LIBRE

18 590 NUT, JAM 3/8-16 CONTRE-ECROU 3/8-16

2O 15012O1 GUIDE, ROD BELT GUIDE DE COURROIE

22 71060 WASHER, SPTLK .31X.58X.08 RONDELLE-FREIN .31X.58X.08

24 710097 SCREW, 5/18-24X 0,75 VIS 5/16-24X 0.75

25 FRAME ASSEMBLY CHASSIS DE MONTAGE, MOTEUR

25-1 1501062E737 PLATE, ENGINE MOUNT PLAQUE DE MONTAGE, MOTEUR

25-2 310169 SCREW 1/4-20 X .63 VIS 1/4-20 X .63

25-3 25x02O SCREW 5/16-18 X .50 VIS 5/16-18 X .50

25-4 1501040E737 FRAME, MOTOR BOX SUPPORT DE MONTAGE, MOTEUR

26 282045 KEY, IGNITION CLE

27 226462 DEFLECTOR, MUFFLER DI_FLECTEUR DE SILENCIEUX

28 810140 SCREW VIS

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=CESDERECHANGE

FRAME /BATI

1(36 160

111

Ref. Engine Page _ q__

162

122 _

123 /

91 168

Ref. Auger

Housing Page

Ref. Drive Page

103

149 107

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDE RECHANGE

FRAME /BATI

Key No.

NO6urle Part No.

sch6ma N° de piece Description

90 1501055E701 COVER, BOTTOM

91 310169 SCREW, 1/4-20X .63

103 1501782 YZ IDLER ASSEMBLY, AUGER

105 711682 PIN, HAIR .38DIAX1.64LG

106 761761 PIN, CLEVIS 3/15" DIA

107 155x159 SPRING, TENSION

108 761675 YZ ASSY., SPRING ATTACH

110 585781 BOLT, 3/8-15X1.25 CARR.

111 711617 WASHER, FLAT

122 25x020 SCREW, TAP 5/16-18 X.50

123 25x021 SCREW, TAP 5/16-18 X .75

148 1502120 PULLEY, IDLER

149 590 NUT 3/8-15

160 1502184 COVER, BELT

162 26x306 SCREW, TAP

167 71067 WASHER, FLAT

168 1501200 SPACER, AUGER BRACKET

169 760539 LID, TOOL BOX

Description

PANNEAU INFERIEUR

VIS 1/4-20X ,63

BRAS DE POULIE LISRE. ENTRAINEMENT DES LAMES

GOUPILLE BETA

GOUPILLE

RESSORT DE TENSION

PATrE DE FIXATION POUR RESSORT

BOULON BLOQUANT 3/8-16Xl.25

RONDELLE PLATE

VIS 5/16-18 X .50

VIS 5/16-18 X .75

PULLIE LIBRE

_CROU 3/8-16

CARTER DES COURROIES

VIS

RONDELLE PLATE

ENTRETOISE, FIXATION DES LAMES CHASSE-NEIGE

COUVERCLE DE BOITE A OUTILS

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=CESDERECHANGE

DRIVE /BATI DE MONTAGE DU MOTEUR

/236

Ref. ShiftYoke Page

Ref. Wheel

204 203 '

238

Ref. Wheel \

Page

213

f _ _-_'_ _ 229

Ref. Frame Page /,,_: _,\

f. Wheel 200 \

Page \

221

225

223

226

\ \

I \

230

22O

218

207

215

227

Wheel Page

220

208 q

213

217

218

212

213

210 \

238

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDE RECHANGE

DRIVE /BATI DE MONTAGE DU MOTEUR

Key No.

NOsur le Part No.

sch6ma N ° de piece Description Description

200 1501092 YZ LF AXLE, SWING PLATE YZ PANNEAU ARTICULE

201 879851 CHAIN, ROLLER #420 xl 9.00 CHAINE A GALETS #420 xl 9,00

203 334183 BEARING AND RETAINER, ASSY ROULEMENT AVEC FIXATION

204 579858 WASHER RONDELLE

206 25x020 SCREEN,TAP 5/16-18x0.5 VIS, 5/15-18xo.5

207 1501238 ASS"(, HEX SHAFT ARBRE HEXAGONAL

208 579868 CHAIN, ROLLER #420 xl 8.00 LG CHAINE A GALETS #420 x18.00 LG

210 337029 BEARING, TRUNION CLUTCH R PALIER

212 1501435 WHEEL, FRICTION DISC ROUE DE FRICTION

213 001X38 BOLT BOULON

215 303008 NUT, KEPS HEX 1/4-20 ECROU 6 PANS 1/4-20

217 579859 RING, RE-TEXT ClRCLIP

218 579858 WASHER RONDELLE

220 334163 BEARING AND RETAINER, ,t_Sy ROULEMENT AVEC FIXATION

221 25x020 SCREW, TAP 5/18-18 x .5 VIS, 5/16-18 x .5

223 15Ol115 ASSY. FRICTION PULLEY POULIE, SYSTEME DE FRICTION

225 1501057 YZ LF PLATE, SWINGING YZ PANNEAU ARTICULE

226 1501158 SPACER, FRICTION PULLEY ENTRETOISE DE POULIE, SYSTEME DE FRICTION

227 15x114 NUT, FLANGE LOCK 3/8-24 ECROU A COLLET 3/8--24

229 11x30 RETAINER, RING ClRCLIP

230 1502105 YZ LF ASSY, SPRING LINK YZ TRINGLE D ATTACHE DES RESSORTS

232 11x30 RETAINER, RING CIRCLIP

234 155x112 SPRING, EXTENSION RESSORT D'EXTENSION

236 1501237 WLD. INTERMED SPROCKET 331/7 PIGNON INTERMEDIAIRE 33T/7

238 71074 WASHER, FLAT RONDELLE PLATE

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

AUGER HOUSING /VIS SANS FIN

484

485

480

4-91

522

523

5OO

511

493

522

523

z\ \

524

Ref. Gear Case Assy

525

520

525

\\ 540

544

541

510

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII CESDERECHANGE

AUGER HOUSING /VIS SANS FIN

Key No.

N° surle Part No.

sch6ma N° de piece Description Description

480 583146 PULLEY, 4L 8.40 OD. POULIE 4L 8,40

482 2001022 KEy, SQUARE 3/16 X3/4 CLAVETTE A SECTION CARREE 3/16 X 3/4

484 15x112 NUT, .50-20 HEXWDFLLK ECROU, 6 PANS ,50-20

485 1501158 SPACER, FRICTION PULLEY ENTRETOISE DE POULIE, SYSTEME DE FRICTION

490 582957 YZ RETAINER, BALL BRNG CAPUCHON DE ROULEMENT ABILLES

491 1501389 BEARING, BALL ROULEMENT A BILLES

493 0Olx92 BOLT, HEX 5/16-18X .50 BOULON 6PANS 5/16-18X .50

499 710026 NUT, 5/16-18 HEXWDFLLK ECROU 6PANS 5/16-18

500 1501695E737 HOUSING, ASSY CARTER DES LAMES CHASSE-NEIGE

510 760659E701 BLADE, SCRAPER LAME RACLEUSE

511 001x45 BOLT, 5/16-18}(0.62 BOULON 5/16-18x0.62

514 710026 NUT, 5/18-18 ECROU 5/18-18

520 760591E701 AUGER, ASSY, LH LAME CHASSE-NEIGE (VIS SANS FIN), GAUCHE

521 760592E701 AUGER, ,aSS'(, RH LAME CHASSE-NEIGE (VIS SANS FIN), DROITE

522 9524 SCREW, 1/4-20)(1,75 VIS 1/4-20Xl .75

523 3943 SPACER, SLEEVE ENTRETOIS E

524 73826 NUT, 1/4-20 ECROU 1/4-20

525 53757 BEARING, FLANGE PALER A BRIDE

527 25x021 SCREW, 5/16-18X .75 VlS 5/16-18)( .75

540 309016E701 SKID, HEIGHT ADJUST PATIN REGLABLE

541 340720 BOLT, 5/16-18 X .75 BOULON 5/16-18 X .75

544 710026 NUT, 5/16-18 ECROU 5/16-18

550 1501576 BRUSH, CLEANOUT OUTIL DE NETTOYAGE

551 1501672 CLIP, RETAINER PINCE

552 06x115 SCREW VIS

553 15x146 NUT ECROU

554 578063 BLOCK BLOQUE

-- 1501216 KIT, SHEAR BOLT KIT, BOULON DE CISAILLEMENT

-- 680230 Z WRENCH CU5

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIIt:CESDEREGHANGE

DISCHARGE CHUTE /DI=FLECTEUR DE GOULOTrE

599 583

6OO

6O0

597_

584

594 ""_-588

610

609

606

602

603

I----607

Ref. Auger Housing Page

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE-NEIGE C950524312A PIECES DE RECHANGE

DISCHARGE CHUTE /DEFLECTEUR DE GOULOTTE

Key No.

N° sur le Part No.

schema N ° de piece

582 340720

583 12021

584 71038

588 6711

593 6711

594 71071

695 71060

596 71071

597 57171

599 002x97

600 1602118E701

601 2x100

602 71071

603 71038

604 760268

606 1501932 YZ

607 02x101

609 15xl 45

610 337227

611 1501282

Description

BOLT,CARRIAGE 5/16 18 X.75

WASHER, PLASTIC

NUT, 5/16 18 REGHEX NYLOCK

WASHER PLASTIC

WASHER FLAT

WASHER SPLIT

WASHER FLAT

KNOB, T 3.00

BOLT, 5/16 18X1.06

CHUTE ASSEMBLY

BOLT, 5/16 18 Xl.00

WASHER, FLAT

NUT, 5/16 18 HEXNYL

FLAP, CHUTE

CHUTE COLLAR

SCREW, 1/4 20X0.75

NUT, 1/4 20 HEX NYLOCK

RETAINER RING INNER

RETAINER RING OUTER

Description

BOULON AUTOBLOQUANT 5/16 18X.75

RONDELLE PLASTIQUE

ECROU 6 PANS 5/16 18 REGHEX NYLOCK

RONDELLE PLASTIQUE

RONDELLE PLATE

RONDELLE FREIN

RONDELLE PLATE

POIGNEE T 3.00

BOULON 5/16 18X1.00

ENSEMBLE DEVERSOIR

BOULON 5/16 16X1.00

RONDELLE PLATE

ECROU 6 PANS 5/16 18 HEXNYL

BAVETrE DE DEVERSOIR

COUVERCLE DE COURONNE DE DEVERSOIR

VIS 1/4 20 X 0.75

ECROU 6 PANS 1/4 20 NYLOCK

COURONNE INTERNE

COURONNE EXTERNE

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=GESDERECHANGE

GEAR CASE/B0|TER

340

326

305

310

320

306

/a21a22 /aiD

323

300

Key No. Part No.

N° sur le N° de

5ch6ma piece Description

300 896 CASE, GEAR, RH

301 895 CASE, GEAR, LH

303 910828 SCREW, 5/16-24 X1.00

304 71100 NUT, 5/16-24

305 330434 SCREW, 5/16-24 X 1,50

306 53749 PLUG, PIPE

310 780151 SEAL, OIL

311 53743 BEARING

312 53748 WASHER, FLAT

313 760527 SHAFT, AUGER OUTPUT

314 897 GASKET, GEAR BOX

315 53730 WORM GEAR

316 73905 KEY, WOODRUFF #91

320 53737 RING, GUAD

321 583126 BEARING, FLANGE

322 48275 WASHER, FLANGE

323 50684 BEARING, ROLLER

324 48275 WASHER, FLAT

326 50795 KEY

527 53732 GEAR, WORM

330 53731 BEARING

340 1501147E701 IMPELLER

-- 333431 10oz TUBE LUBRIPLATE

324

* (NOT ILLUSTRATED)

314

327

330

311

312/

313 ."/

*(NON ILLUSTRE)

301

304

Description

BOITER COTE DROIT

BOITER COTE GAUCHE

VIS, 5/16-24 X1.00 PO.

I_CROU, 5/16-24

VIS, 5/16-24 X 1.50

PRISE DE PIPE

JOINT/_ LE'VRE

PALIER

RONDELLE PLATE

ARBRE DE VIS SANS FIN

JOINT PLAT

PIGNON

CLAVE77-E DEMI-LUNE No. 91

ANNEAU DE QUADRUPLE

PALIER

RONDELLE

PALIER

RONDELLE, PLATE

CLAVE37-E

PIGNON

PALIER

ARBRE DE LA TURBINE

10oz LUBRIPLATE

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

WHEELS /ROUE

679

675

671

678 654

650 _"/

655 /

.652

Ref. Drive Page

655 671

676

673

WHL100A

680

Key No.

NOsurle

$cl_ma

650

652

653

654

655

671

673

675

676

677

678

879

680

PaN No.

N° de piece

1501583YZ

1501089

01x193

15x145

1501114

017x83

1501138

1501808

577015

15x145

239

73842

1501809

Description

SHAFT, AXLE

SPRKT & RUB

SCREW, 1/4-20 x 1.75

NUT, 1/4-20 HEX NYLOCK

BEAMING, AXLE

WASHER, FLAT

BUSHING, WHEEL

TIRE & RIM, RIGI-_

SCREW, 1/4-20X1.75 HH

NUT, 1/4-20 HEX NYLOCK

RING, RET

PiN, KLIK .25 X 1.38 DIA

TIRE & RIM, LEFT

Description

D'ARBRE, ROUE

ROUE DENTEE MONTAGE

VIS, 1/4-20X 1.75 PO.

€:CROU, 1/4-20

PALIER

RONDELLE PLATE

PALIER,

ROUE MONTAGE, GAUCHE

VIS, 1/4-20)(1,75 PO.

IFCmOU, 1/4-20

RONDELLE DE RETENUE

GOUPILLE/_ ANNEAU

ROUE MONTAGE, DROIT

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII_CESDEREGHANGE

HANDLE /POIGNI_E

766 739

735 _\ 766 736

720 738

739

738

737

738 738

740

741

721 722

723

724 _765

728 /

751

/732 733 /75

730 731 /8

745

743

76,3

Ref. Engine Page

_760

759

745 762

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE 0950524312A PII:CES DE RECHANGE

HANDLE /POIGNI=E

Key No. Part No.

N° 3urle N° de

sch6ma piece Description

720 310614E701 HANDLE, UPPER

721 7288 SCREW, 3/8-16 X 3

722 71072 WASHER, FLAT

723 71062 WASHER

724 71044 NUT, 3/8-16

728 7289 STOP, PLASTIC

730 71007 SCRE3N, 3/8-16 X2

731 71072 WASHER, FLAT

732 71062 WASHER

733 71044 NUT, 3/8-16

735 5146E701 HANDLE, RIGHT

736 5142E701 HANDLE, LEFT

737 760074 PIN, PIVOT CLUTCH

738 3535 NUT, PUSH ON CAP

739 4049 BUMPER, RECTANGLE

740 1502113 CABLE, DRIVE

741 761872 CABLE, AUGER CLUTCH

743 313441 BRACKET, CABLE ADJUSTER

744 1673 SPRING, AUGER CLUTCH

745 15x145 NUT, 1/4-20

750 1501449E701 HANDLE, LOWER

751 25x021 SCREW, TAP 5/16-18 X .75

750 579860 SPOOL-CABLE, AUGRT CLUTCH

760 1501059 YZ BRACKET, CABLE SPOOL YZ

762 1501122 CABLE, LOWER DRIVE 12"

763 001798 BOLT, HEX 1/4-20 X 1.5

765 308146 BOOT, CLUTCH SPRING

766 333928 GRIP

Description

POIGNEE, PARTIE SUPERIEURE

VIS 3/8-16 X3

RONDELLE PLATE

RONDELLE

ECROU 3/8-16

CAPUCHON, PLASTIQUE

VlS 3/8-16 X 2

RONDELLE PLATE

RONDELLE

ECROU 3/8-16

POIGNEE, DROIT

POIGNEE, CAUCHE

AXE DE MANETIE DE COMMANDE

ECROU BORGNE

PATIN RECTANGULAIRE

C._3,BLE,COMMANDE DU SYSTEME DE TRACTION

C/_BLE, COMMANDE DES LAMES CHASSE-NEIGE

PIECE DE REGLAGE DU CABLE, SYSTEME DE TRACTION

RESSORT DE CABLE, COMMANDE DES LAMES

ECROU 1/4-20

POIGNEE, PARTIE INFERIEURE

VIS 5/16-18 X .75

BOBINE DE PASSAGE DE CABLE, COMMANDE DES LAMES

ATrACHE DE LA BOBINE DE PASSAGE DE CABLE

CABLE, PARTIE BASSE 12", COMMANDE DES LAMES

BOULON 1/4-20Xl,5

GAINE DE RESSORT, SYSTEME DE TRACTION

POIGNEE

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

735

766

771

Ref. Handle Page

CONTROL PANEL /PANNEAU DE COMMANDE

760

763

764

763

764

Ref. Handle Page

• 779

761

765

772

770

773

781782

784

774

811

809

810

812

813

CRAFTSMAN 30" SNOW BLOWER 0950524312A REPAIR PARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

CONTROL PANEL /PANNEAU DE COMMANDE

Key No.

N°surle Part No,

sch6ma N° de piece Description Description

735 71045 NUT, 3/8-16 HEXJAM ECROU, 3/6-18

760 308905E701 BRACKE_, SHIFT CONTROL SUPPORT OU LEVIER DE COMMANDE

761 762148 CARR. BOLT,1/4-20 X 2 BOULON, 1/4-20 X 2

763 71059 WASHER, SPLIT RONDELLE-FREIN

764 71034 NUT, 1/4-20 HEX CONTRE-EOROU 1/4-20

765 6056E737 CONTROL PANEL PANNEAU DE COMMANDE

766 3809 CARR. BOLT, 1/4-20 X 0.63 BOULON, 1/4-20 X0.63 PO.

770 305260E701 SHIFT LEVER ASSY LEVlER DE COMMANDE MONTAGE

771 302900 SCREW, 5/16-18Xl .75 VIS, 5/16-18X1,75 PO.

772 50786 SPRING RESSORT

773 71071 FLATWASHER RONDELLE PLATE

774 71038 NUT, 5/16-18 NYLON HEX FtCROU INDESSERRABLE 5/16-18

779 304437 GRIP POMMEAU

781 71071 WASHER, FLAT .849X.69X.066 RONDELLE PLATE

782 71081 PIN, COTI'ER GOUPILLE, FENDUE

784 1582O19 ROD, SPEED CONTROL TIGE DE COMMANDE DE VITESSE

805 71042 NUT, 5/16-18 E_CROU

806 6352 ADAPTER, SPEED ROD -yz AOAPTATEUR, TIGE DE COMMANDE DE

LA VITESSE -YZ

808 50782 BALLJOINT, STEEL -YZ ROTULE EN AClER -YZ

809 71060 WASHER RONDELLE

810 71042 NUT, 5/16-24 ECROU

811 579944 FLANGED BEARING PALIER

812 1501110 YZ ROD ASS'(, YOKE PANEL LEVlER DE CHANGEMENT DE VlTESSE

813 11X30 RING, RETAINER CIRCLIP

CRAFTSMAN 30" SNOW BLOWER C950524312A ,REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PIECESDERECHANGE

CHUTE ROD /GOULOTTE TIGE

856

855

Ref. Handle Assy

865

868

854 862

861

860

867

864

Ref. Auger Housing Assy

870

852-8

852-11

852-9

852-5

/852-13

852-10

852-2

852-6

\\\

869

852-7 852-3

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=CESDERECHANGE

CHUTE ROD /GOULO'rTE TIGE

Key No.

N°surle Part No.

sch6ma N° de piece Description

852-1 1501533 YZ ASSEMBLY, YOKE & ROD

852-2 164x37 SPRING

852-3 1501067 GEAR, CHUTE ROTATION 9T

852-5 579493 PIN, CO]-r ER

852-6 1501306E701 BRACKET, CHUTE GEAR

852-7 1501293 PIN, HAIR

852-8 1501075 YZ ASSEMBLY, YOKE ADAPTER YZ

852-9 711082 PIN, HAIR

852-10 578060 PIN, UNIVERSAL JOINT

852-11 578309 PIN, CLEVIS

852-13 578063 HOUSING, UNIVERSAL

854 307399 KNOB, SLEEVE

855 309312 FLA33NASHER

856 73664 NUT, PUSH ON 3/8"

850 1501456 EYE BOLT 3/8-15X5.00

861 148 GROMMET, EYE BOLT

862 1501457 BOOT, EYE BOLT

863 71045 NUT, 3/8-16 HEXJAM

864 71072 FLA'rWASH ER .406X.81X.065

865 309344 ADAPTER, BOOT

867 71045 NUT, 3/8-16 HEXNYL

868 002x98 BOLT, CARRIAGE 1/4-20 X 1.00

869 15x145 NUT, 1/4-20

870 1501074 YZ CRANK, ASSY CHUTE

Description

ENSEMBLE TRINGLE-CHAPE

RESSOP_I"

PIGNON DE ROTATION DU DEVERSOIR

GOUPILLE FENDUE

PATrE DE FIXATION DU PIGNON

GOUPILLE

ENSEMBLE ADAPTATEU R-CHAPE

GOUPILLE BETA

GOUPILLE DE JOINT UNIVERSEL

GOUPILLE DE CHAPE

CAPUCHON DE JOINT UNWERSEL

POIGNEE DE MANIVELLE

RONDELLE PLATE

CAPUCHON 3/8"

BOULON A OEIL 3/8-15X6.00

OBLLET

BOUT]E

CONTRE-ECROU 6 PANS 3/8-16 HEXJAM

RONDELLE PLATE .405X.81X.066

ADAPTATEUR

ECROU 5 PANS 3/8-16 HEXNYL

BOULON AUTOBLOQUANT 1/4-20X1.00

ECROU

MANIVELLE DE DEVERSOIR

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=CESDERECHANGE

HEADLIGHT /MONTAGE DU PHARE

620

621

622

623

631 625

633 626

Ref. Handle Page

624

628

627

629

630 J

634

Key No.

NOsurle Part No.

sch6ma N° de pl_ce

620 583490

621 762343

622 1501514

623 307781

624 1501455

625 4029 YZ

626 002)(88

627 580527

628 71061

629 71060

630 15x144

631 235

632 71060

633 15x144

634 66426

Description

HOUSING, HEADLIGHT UPPER

HEADLIGHT, ASSY *

HOUSING, HEADLIGHT LOWER

SCRE-3N,#8X1.75

WIRING HARNESS, HALOGEN

BRACKET, HEADLIGHT

BOLT, CARRIAGE - 5/16-18X2.00

WASHER, SADDLE

WASHER, EXLK .32X.60X.040

WASHER, SPTLK .31X.58X.08

NUT, 5/16-18 REGHEX

SCREW, 5/16-18X2.00

WASHER, SPTLK

NUT, 5/16-18 REGHEX

TIE, CABLE

Description

BOITER SUP_RIEUR OU PHARE

MONTAGE DU PHARE *

BO/TER INFERIEUR DU PHARE

VIS, #8 X 1,75 PO.

FILS ELECTRIQUES DU PHARE, HALOGENE

SUPPORT MONTAGE DU PHARE

BOULON MI_CANIQUE 5/16-18X2,00 PO.

RONDELLE CINTR_E

RONDELLE ,32X,60X,040

RONDELLE FENDUE ,31X,58X,08

E_OROU,5116-18

VIS, 5/16-18X2,00 PO.

RONDELLE FENDUE

I_OROI_I,5/16_18

CABLE DE BRIDE

* Forreplacementbulb,useStandardGE orPhillips#894, *PourI'ampoulede rechange,employezla GE standardou #894Phillips.

CRAFTSMAN 30" SNOW BLOWER C950524312A REPAIRPARTS

CRAFTSMAN 30" CHASSE NEIGE C950524312A PII=GESDERECHANGE

DECALS /AUTOCOLLANTS

t832-

_I_835-

_834

}33

826

[]

Key No.

Nosur le Part No.

schdma Node piece

823 48x5966

824 48x5968

826 48x5958

828 48x5579

829 48x5593

830 48x5594

831 327921

832 48x5565

933 48x5960

834 761048

835 340568

- - 48x5993

- - 401428

Description

DECAL DANGER CHUTE HAND

DECAL DANGER FOOT

DECAL CRAFTSMAN 11.5/30

DECAL THROWN OBJECTS

DECAL DRIVE CLUTCH

DECAL AUGER CLUTCH

DECAL GEAR SELECTOR

DECAL CRAFTSMAN

DECAL CLEAN & CLEAR BRUSH

DECAL TOOLBOX INFORMATION

DECAL SPEED SELECT

DECAL O.P.E.I.

MANUAt OWNER'S

Description

AUTOCOLLANT, DANGER MAINS. _:JEOTION

AUTOCOLLANT, DANGER PIEDS

AUTOCOLLANT, CRAFTSMAN 11.5/30

AUTOCOLLANT, PROJECTION D'OBJETS

AUTOCOLLANT, EMBRAYAGE ROUES

AUTOCOLLANT, EMBRAYAGE FRAISE

AUTOCOLLANT. S(:LECTEUR VITESSE

AUTOCOLLANT, CRAFTSMAN

AUTOCOLLANT, BROSSE ,_ NETFOYER/DC:BLAYER

AUTOCOLLANT, INSTRUCTIONS BOh'E/%. OUT]LS

AUTOCOLLANT, SELECTEUR VITESSE

AUTOCOLLANT, O.P.E.L

MANUEL D'UTILISATION

BRIGGSANDSTRATTONENGINE21Cl14-0370-E1

MOTEURBRIGGSANDSTRA'rroN21Cl14-0370.E1

1019 LABEL KIT 1

5251 523

287

524

REPAIRPARTS

PIECESDERECHANGE

1351 f

3o7_

718_

55_

746

742_

1281 _1

22_

1095 VALVE GASKET SET

Assemblies Include all parts shown In frames.

Les assemblages comprennent toutes ]es pi_ces illustrdes dans les encadrements.

BRIGGSANDSTRATrONENGINE21Cl14-0370-E1

MOTEURBRIGGSANDSTRATrON21Cl14-0370-E1

Key No.

No sur le Part No.

sch6ma N° de piece Description

1 697702 Cylinder Assembly

2 698340 Kit-Bushing/Seal (Magneto Side)

3*391086 Seal-Oil (Magneto Side)

7*_.697690 Gasket-Cytinder Head

12 *694963 Gasket-Crankcase

15 695757 Plug-Oil Drain

16 696412 Crankshaft

18 696914 Cover-Crankcase

19 698340 _t-Bushing/Seai (PTO Side)

20 *391086 Seal-Oil (PTO Side)

21 281658 Cap-Oil Fill

22 695174 Screw (Crankcase Cover/Sump)

24 222698 Key-Flywheel

25 697693 Piston Assembly (Standard)

....... Note .....

697695: Piston Assembly (.020" Oversize)

26 697692 RingSet (Standard)

....... Note .....

697698: Ring Set (.020" Oversize)

27 690975 Lock-Piston Pin

28 696581 Pin-Piston

29 694691 Rod-Connecting

30 694692 Dipper-Connecting Rod

32 690976 Screw (Connecting Rod)

46 790496 Camshaft

51 .A*.694874 Gasket-Intake

51A .A.,694875 Gasket-intake

69 691685 Plug-Oil Drain

122 _.,694876 Spacer-Carburetor

146 690979 Key-'l] ming

219 693578 Gear-Governor

220 691724 Washer (Governor Gear)

267 691693 Screw (Dipstick Tube)

306 697240 Shield-Cylinder

307 691660 Screw (Cylinder Shield)

356 695438 Gasket Set-Engine

523 790477 Dipstick

524 691876 Seal-O Ring (DipstickTube)

525 790478 Tube-Dipstick

529 791822 Grommet

552 694674 Bushing-Governor Crank

718 690959 Pin-Locating

718A 695178 Pin-Locating

741 691288 Gear-_ming

742 692564 Retainer-E Ring

746 694679 Gear-Idler

868 *A696968 Seal-Valve

883 ,/.695398 Gasket-Exhaust

998 696683 Pipe-Oil

1019 790459 Kit-Label

1022 ,/.690971 Gasket-Rocker Cover

1095 695449 Gasket Set-VaNe

1351 790017 Stud (Cylinder Shield)

REPAIRPARTS

PIECESDERECHANGE

Description

Cylindre

Kit -entrstoise/joint (face magndto)

Joint &huile (face magneto)

Jointde culasse

Joint de bioc-cylindre

Vie de vidange

Viiebrequin

Carter de vilebrequin

Kit -entretoise/ioint (face prisede force)

Joint _. huile (face prise de force)

Bouchon - remplissage d'huile

Vie (carterde vilebrequin/cuve)

Cl6 - volant d'inertie

Piston (standard)

Remarque .....

697695: Piston (0,020" surdimensionn_)

Jeu de segments (standard)

Remarque .....

697698: Jeu de segments (0,020" surdimansionn_)

Verrouillage- axe de piston

Goupille -piston

Tringle de raccord

Plongeur-tringle de raccord

Vis- (tringlede raocord)

Arbre& came

Joint - alimentation

Vie de vidange

Entretoise -carburateur

CI_ de r6glage

Engrenage de gouvemeur

Rondelle (engrenage de gouverneur)

Vie (tube de jauge)

Bouclierde cylindre

Vie (bouclierde cylindre)

Jeu de ioints - moteur

Jauge

Joint torique (tube de jauge)

Tube - jauge

Passe-ills

Entretoise - maniveUe de gouvemeur

Goupille de montage

Engrenage - r_glage

Bague de retenue

Poulie libred'engrenage

Joint de soupape

Joint d'echappement

Conduite - huile

Kit d'6tiquettes

Joint - eache-culbuteurs

Jeu de joints - soupape

Geujon(gaJnedecyllndre)

BRIGGSANDSTRATrONENGINE21C114-0370-E1

MOTEURBRIGGSANDSTRA'rroN21C114.0370-E1

122 51A_

95 70

117

369 t

105

_ 137_

1127

632

REPAIRPARTS

PIi:CESDERECHANGE

1275

o14=6) 1171_ _)

337

=5C_

121 CARBURETOR OVERHAUL KIT

122 51A

105

117 127 0137 (_

633

°33°

Assemblies include all parts shown in frames.

Lee assemblages comprennent routes lee pi_css illustr6es dans les encadrements.

BRIGGSANDSTRATrONENGINE21C114-0370-E1

MOTEURBRIGGSANDSTRATTON21Cl14.0370.E1

Key No.

Nosurle Part No.

sch6ma N°de piece Description

5 697233 Head-Cylinder

7 *4697690 Gasket-Cylinder Head

11 696750 Tube-Breather

13 690360 Screw (Cylinder Head)

33 499596 Valve-Exhaust

34 697464 Valve-Intake

35 694865 Spring-Valve (Intake)

36 694865 Spring-Valve (Exhaust)

42 499586 Keeper-Valve

45 690977 Tappet-Valve

51 ._o_694874 Gasket-Intake

61A ._,.694875 Gasket-Intake

96 690718 Screw (Throttle Valve)

97 696387 Shaft-Throttle

98 e695408 Kit-Idle Speed

104 e694918 Pin-Float Hinge

105 e696136 Valve-Float Needle

108 696736 Valve-Choke

109 696735 Shaft-Choke

117 e696134 Jet-Main (Standard)

116 696135 Jet-Main (High Altitude)

121 696146 Kit-Carburetor Overhaul

122 _,.694876 Spacer-Carburetor

125 696737 Carburetor

127 e690727 Plug-Welch

130 696139 Valve-Throttle

133 694914 Float-Carburetor

135 696142 Tube-Fuel Transfer

137 eO695426 Gasket-Float Bowl

192 690083 Adjuster-Rocker Arm

337 491055 Plug-Spark

369 695422 Spring-Float Bowl

383 19374 Wrench-Spark Plug

632 695917 Spring/Link-Mechanical Governor

633 e,690998 Seal-Choke/Throttle Shaft

635 691909 Boot-Spark Pug

798 697967 Screw (Rocker Arm)

868 _A690968 Seal-Valve

883 *_695396 Gasket-Exhaust

914 693732 Screw (Rocker Cover)

975 696138 Bowl-Float

977 696147 Gasket Set-Carburetor

1022 *A690971 Gasket-Rocker Cover

1023 698042 Cover-Rocker

1026 695177 Rod-Push

1029 690972 Arm-Rocker

1100 690973 Pivot-Rocker Arm

1127 695407 Screw (Float Bowl)

1171 696754 Stud (Rocker Cover)

1275 696757 Nut (Rocker Cover)

REPAIRPARTS

PIECESDERECHANGE

Description

Culasse

Joint de culasse

Tube reniflard

Vis (Culasse)

Soupape d'dchappement

Soupape d'alimentation

Ressortde valve (d'alimentation)

Ressortde valve (d'_chappement)

Blocage -valve

Soupape - valve

Joint d'alimentation

Vis (valve d'acc_l_rateur)

Arbre d'acc_l_rateur

Kit - ralenti

Axe - charni_rede niveau

Valve -Aiguille de niveau

Valve de starter

Arbre de starter

Gicleur principal(Standard)

Gicleur principal(haute altitude)

Kit de remplacemntde carburateur

Entretoisede carburateur

Carburateur

Pastilled'obturation

Valve d'accdlSrateur

Niveau de carburateur

Condulte de carburant

Joint -cuve ducarburateur

Piece de reglage -culbuteur

Bougie d'allumage

Ressort -cuve du carburateur

Cle &bougie

RessortJLiaison-gouvemeur

Joint - starter/arbre d'acc_ldrateur

Protecteurde caoutchouc- bougie d'allumage

Vis (cu]buteur)

Joint -valve

Joint - dchappement

Vis(cache-culbuteurs)

Cuve du carburateur

Jeu de joints - carburateur

Joint - carter des culbuteurs

Carter des culbuteurs

Tringle a pression

Culbuteur

Pivot - culbuteur

Vis (cuve du carburateur)

Goujon (carter de oulbuteur)

I_crou (carter de culbuteur)

BRIGGSANDSTRA'I-rONENGINE21Cl14.0370-E1 , REPAIRPARTS

MOTEURBRIGGSANDSTRATTON21Cl14-0370-E1PIECESDERECHANGE

3O9

1119

334

397_ 73_

613 _ 613Aq'_,

597_

456 _6899_ _

1005

1070 455

332

190 _

3o_

599@ 55

121

1211

1036 EMISSIONS LABEL

g30

_2 @

Assemblies include all parts shown in frames,

Lee assemblages comprennent toutes les pi_ces Illustr6es dans lee encadrements,

BRIGGSANDSTRATI'ONENGINE21C114-0370-E1

MOTEURBRIGGSANDSTRATrON21C114-0370-E1

Key No.

NO$ur le Part No.

sch6ma N° de pl_ce Description

23 695485 Flywheel

37 699047 Guard-Flywheel

55 696710 Housing-Rewind Starter

58 693389 Rope-Starter (Cutto Required Length)

60 695740 Grip-Starter Rope

65 697725 Screw (Rewind Starter)

78 695724 Screw (Flywheel Guard)

187 698080 Line-Fuel (Molded)

190 692127 Screw (Fuel Tank)

300 699211 Muffler

304 791479 Housing-Blower

305 691108 Screw (Blower Housing)

309 698112 Motor-Starter

332 694685 Nut (Flywheel)

333 495859 Armature-Magneto

334 691061 Screw (Magneto Armature)

356 692603 Wire-Stop (Rocker Switch)

455 697226 Cup-Flywheel

456 692299 Plate-Pawl Friction

459 281505 PawI-Rachet

474 791743 Alternator

578 790481 Wire Assembly

592 690800 Nut (Rewind Starter)

597 691696 Screw (Pawl Friction Plate)

601 95162 Clamp-Hose

608 699335 Starter-Rewind

613 695312 Screw (Muffler)

613A 696705 Screw (Muffler)

635 691909 Boot-Spark Plug

689 691855 Spring-Friction

697 698113 Screw (Starter Motor)

727 697465 Cover-Starter Drive

732 691097 Screw (Starter Drive Cover)

851 692424 TerminaJ-Spark Plug

853 790455 Wire-Adapter

883 .A695398 Gaskst-Exhaust

930 696709 Guard-Rewind

967 694261 Cap-Fuel

972 694260 Tank-Fuel

1005 694684 Fan-Flywheel

1036 790466 Label-Emissions

1070 690364 Screw (Flywheel Fan)

1119 691183 Screw (Alternator)

1210 498144 Pulley/SpringAssembly (Pulley)

1211 498144 Pulley/Spring Assembly (Spring)

REPAIRPARTS

PIECESDERECHANGE

Description

Volant d'inertie

Carter (volant d'inertie)

Carter (d_marreur & rappel)

Corde de lanceur & rappel

(Iongueur sur demande ou standard)

Poign_e de lancaur & rappel

Vis (d_marreur &rappel)

Vis (Carter de volant d'inertiel)

Conduite de carburant (moulde)

Vis (R(_servoir d'essence

SUencieux

Carter du chasse-neige

Vis (carter du chasse-neige)

Moteur de d_marreur

€:crou (volant d'inertie)

Armature du magndto

Vis (armature du magneto)

Butte de c&ble (commutateur & bascule)

Cache - volant d'inertie

Plaque - friction & cliquet

Cliqust

Alternateur

Faisceau de c&bles

I_crou (d_marreur & rappel)

Vis (Plaque de friction & cliqust)

Pinca & tubulure

D_marreur & rappel

Vis (silencieux)

Vie (silencieux)

Protecteur de caoutchouc - bougie d'allumage

Ressort - friction

Vis (moteur du ddmarreur)

Carter - entrai'nement du d_marreur

Vis (Carter de I'entrainement du d_marreur)

Termial - Bougie

Adaptateur de cable

Joint - (_chappemeot)

Carter -lanceur & rappel

Bouchon - r_servoir d'essence

R_servoir d'essence

Veotilsteur - volant d'inertie

E_tiquette_missions

Vis (ventilateur du volant d'inertie)

Vis (alternateur)

Jeu de poulie et ressort (poulie)

Jeu de poulie et ressort (ressort)

BRIGGSANDSTRATrONENGINE21C114-0370-E1

MOTEURBRIGGSANDSTRATrON21C114.0370-E1

,72? 828_ 11_

978 _ /

99o_

1288

1288A

REPAIRPARTS

PII=CESDERECHANGE

1288 _)

347

1230

781

1251 _252

1881 _

222

804A

289

615 O

604

Assemblies include all pa,rts shown in frames.

Les assemblages comprennent toutes les pieces inuefr_es dane lee encadrements.

BRIGGSANDSTRATrONENGINE21C114-0370-E1

MOTEURBRIGGSANDSTRATrON21C114.0370-E1

Key No.

N°surle Part No.

sch6ma N° de piece Description

11 696750 Tube-Breather

53 696753 Stud (Carburetor)

188 690877 Screw (Control Bracket)

209 695491 Spring-Governor (PosRionin No 6 Hole)

222 694866 Bracket-Control

227 694864 Lever-Governor Control

281 697268 Panel-Control

347 698338 Switch-Hocker

472 790472 Knob-Choke Shaft

505 691251 Nut (Governor Control Lever)

562 691119 Bolt (Governor Control Lever)

528 696751 Hose-Primer

564 790282 Screw (ControlCover)

604 790473 Cover-Control

604A 696758 Cover-Control

616 694675 Crank-Governor

663 790282 Screw (ControlPanel)

725 696756 Shield-Heat

731 790470 Hood-Snow

731A 790454 Hoed-Snow

892 *_696749 Switch-Key

976 790221 Primer-Carburetor

990 695756 Key Set

1196 696692 Screw (Snow Hood)

1230 696747 Stud (Control Bracket)

1251 696762 Shield-Snow

1251A 790471 Shield-Snow

1252 696763 Screw (Snow Shield)

1288 696757 Nut (Snow Hood)

1288A 698111 Nut (Snow Hood)

1298 698111 Nut (Heat Shield)

1352 790026 Nut (Spark Plug Shield)

REPAIRPARTS

PII CESDERECHANGE

Description

Tube reniflard

Goujon (carburateur)

Vie (supportdes commandes)

Ressortde r_gulateur(positionnerautrouNo.6)

Support des commandee

Levier de ccmrnande du gouvemeur)

Panneau des commandes

Commutateur_bascule

Bouton - arbre du starter

F:crou(levier de commande du gouvemeur)

Boulon (levier de commande du gouvemeur)

Conduite - boutond'amorce

Vie (Carter des commandes)

Carter des commandes

Manivelle du gouverneur

Vie (panneau de garnissage)

I_cranthermique

Carter - neige

CI_ de contact

Boutond'amorce -carburateur

Jeu de clds

Vie (carter _neige)

Goujon (supportdes commandes)

I_cran _neige

Vis (ecran &neige)

16crou(_cran _neige)

16crou(dcran _neige)

Ecrou (_cran thermique)

Ecrou (_cran &bougie)

NOTES

Just Call:

1-800-4-MY-HOME ®

(1-800-469-4663)

24 hours a day, 7 days a week

For the repair of major brand appliances in your own home ...

no matter who made it, no matter who sold itY

For your nearest Sears Parts & Service location,

to bring in products like vacuums, lawn equipment and electronics.

For Sears Parts & Service, to order the replacement parts,

accessories and owner's manuals that you need to do-it-yourself.

www.sears.ca

To purchase or inquire about a Sears Maintenance Agreement, call:

1-800-361-6665

9 a.m. - 8 p.m. Mon. - Fri. EST, 9 a.m. - 4 p.m. Sat.

Pour service en francais:

1-800-LE-FOYER Mc

(1-800-533-6937)

www.sears.ca

SEARS

HomeCentral

_rM Trademarks of Sears, Roebuck and Co. used under license by Seers Canada

®MC

Marque depos_e/ Marque de commerce de Sears, Roebuck and Co. utilisee en vertu d'une licence de Sears Canada

Craftsman C950524312A User Manual DUAL STAGE SNOW BLOWER Manuals And Guides L0511284

CRAFTSMAN Snowthrower, Gas Manual L0511284 CRAFTSMAN Snowthrower, Gas Owner's Manual, CRAFTSMAN Snowthrower, Gas installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation