Craftsman 315 21449 Users Manual
315214490 315214490 CRAFTSMAN 9 in. SINGLE SPEED BAND SAW - Manuals and Guides 98100165 View the owners manual for your CRAFTSMAN 9 in. SINGLE SPEED BAND SAW #315214490. Home:Tool Parts:Craftsman Parts:Craftsman 9 in. SINGLE SPEED BAND SAW Manual
CRAFTSMAN Saw Band Manual 98100165 CRAFTSMAN Saw Band Owner's Manual, CRAFTSMAN Saw Band installation guides
31521449 dc7652a8-1711-48d5-a238-9cb725532b46 Craftsman Saw 315.21449 User Guide |
2015-01-05
: Craftsman Craftsman-315-21449-Users-Manual-161101 craftsman-315-21449-users-manual-161101 craftsman pdf
Open the PDF directly: View PDF 
.
Page Count: 32
| Download | |
| Open PDF In Browser | View PDF |
Owner's Manual II:RRFTSMRNI 9 in. single speed BAND SAW Model No. 315.214490 Save this manual for future reference. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Sears, Roebuck and Co., Hoffrnan Estates, IL 60179 USA NRTL 972000-488 4-98 • Table of Contents ............................... :...... ..................................................................................................... 2 • Warranty and Intreduction..;':.'::_;:.';_.:............................................................................................................ 2 • Rules For Safe Operatiod .. :L;_;,:....;: ................................................................................................. • Electrical ......... ., ...:.L:.:._],..._.:._;I._...].:........... [............ ;................................................................................... 6 • Glossary and Produ_Sloecifications ...[......................................................................................................... 7 • Unpacking, Loose PartsListian¢l'Toois Needed ........................................................................................... 8 • Labels ............................................................ • Features ....................................................................................................................................................... • Assembly ................................................................................................................................................. 12-13 • Adjustments ............................................................................................................................................. 13-17 • Basic Operation ....................................................................................................................................... 18-19 • Maintenance ............................................................................................................................................ 20-21 • Troubleshooting ............................................................................................................................................ • Exploded View and Repair Parts List ...................................................................................................... • Parts Ordedng / Service ............................................................................................................................... , FULL ONE YEAR WARRANTY _...... 3-5 '............................................................................................ ON CRAFTSMAN 9-10 11 22 24-31 32 BAND SAW If this I'RII FTSMAN" Band Saw fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge. Contact a Sears Service Center for repair. If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 Your saw has many features for making cutting operations more pleasant and enjoyable. Safety, performance and dependability have been given top priodty in the design of this saw making it easy to maintain and operate. _, ,_ _ CAUTION: Carefully read through this entire owner's manual before using your new saw. Pay close attention to the Rules For Safe Operation, and all Safety Alert Symbols including Danger, Warning and Caution. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service. Look for this symbol to point out important safety precautions. Your safety is involved. It means attention!!! WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears Retail Stores. 2 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The Instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING & SAFETY ALERT SYMBOL: Indicatesdanger,wamingor caution. May be used in conjunctionwithothersymbolsorpictographs. A DANGER: Failure to obey a safety waming will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. & WARNING: Failure to obey a safety waming can result in serious injuryto yourself or to others. Always follow the safety precautions to reduce the risk of fire, electdc shock and personal injury, & Note: CAUTION: Failure to obey a safety waming may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury, Advises you of information or instructionsvital to the operation or maintenance of the equipment. IMPORTANT Servicing requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest Sears store for repair. Always use original factory replacement parts when servicing. _k WARNING: Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc. contained in this manual. Failure to comply can • result in accidents involving firs, electdc shock, or serious personal injury. Save owner's manual and review frequently for continuing safe operation, and instructing others who may use this tool. • READ ALL DO NOT leave tools or pieces of wood on the saw while it is in operation. INSTRUCTIONS • KEEP CHILDREN AND VISITORS AWAY. All contact tool or extension cord while operating. GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES. For example; pipes, radiators, ranges; refrigerator enclosures. KEEP GUARDS IN PLACE and in good working order. REMOVE ADJUSTING ENVIRON- visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors manual carefully. Learn the saw's applications and limitations as well as the specific potential hazards related to this tool. • DO NOT USE IN DANGEROUS MENT. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations, or expose them to rain. Keep the work area well lit. KNOW YOUR POWER TOOL. Read the owner's • KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents. • MAKE WORKSHOP CHILD-PROOF with padlocks and master switches or by removing starter keys. • DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. • USE THE RIGHT TOOL. Do not force the tool or attachment to do a job it was not designed for. Don't use it for a purpose not intended. KEYS AND WRENCHES. Get in the habit of checking to see that hex keys and adjusting wrenches are removed from tool before turning it on. • USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. 3 H RULES FOR, SAFE OPERATION (Continued) . When us(rig an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 18 is recommended for an extension cord binding of moving pans, breakage of pans, saw stability, mounting and any other conditions that may affect its operation. A guardor other part that is damaged must be properly repaired or replaced by a qualified service technician at a Sears store to avoid risk of personal injury. 25 feet or less in length. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged. M DRESS PROPERLY. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry. They can get caught and draw you into moving parts. Rubber gloves and nonslip footwear are recommended. Also wear protective hair covering to contain long hair. • NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Do not leave tool until it comes to a complete stop. • USE ONLY CORRECT BLADES. Use the right blade size, style and cutting speed for the material and the type of cut. Blade teeth should point down toward the table. KEEP BLADES CLEAN, SHARP AND WITH SUFFICIENT SET. Sharp blades minimize stalling and kickback. ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. DO NOT REMOVE THE SAW'S BLADE GUARDS. Never operate the saw with any guard or cover removed. Make sure all guards are operating properly before each use. PROTECT YOUR LUNGS. Wear a face or dust mask if the cutting operation is dusty. PROTECT YOUR HEARING. Wear hearing protection during extended periods of operation. KEEP HANDS AWAY FROM CUTTING AREA. Do not hand hold pieces so small that your fingers go under the blade guard. Do not reach underneath work or in blade cutting path with your hands and fingers for any reason. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and it frees both hands to operate tool. DO NOT OVERREACH. balance at all times. t_eep proper footing and A Blade coasts after turn off. DO NOT ABUSE CORD. Never yank cord to disconnect it from receptacle. Keep cord from heat, oil, and sharp edges. • AINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired by a qualified service technician at a Sears store. Stay constantly aware of cord location and keep it well away from the moving blade. DISCONNECT ALL TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power supply. AVOID ACCIDENTAL WARNING: STARTING. Be sure DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by a qualified service technician at a Sears store. switch is off when plugging in. USE RECO••ENDED ACCESSORIES. The use of improper accessories may cause risk of injury. • KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean clothwhen cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. • ALWAYS SUPPORT LARGE WORK PIECES while cutting. To minimize risk of blade pinching and kickback, always support large workpieces. Saw may slip, walk or slide while cutting large or heavy boards. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the blade is unintentionally contacted. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, 4 RULES FOR SAFE OPERATION (Continued) BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE. m m BEFORE CHANGING THE SETUP, REMOVING COVERS, GUARDS, OR BLADE; UNPLUG THE SAW AND REMOVE THE SWITCH KEY. REPLACEMENT PARTS. All repairs, whether electrical or mechanical, should be made by a qualified service technician at a Sears store. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. DO NOT FEED THE MATERIAL TOO QUICKLY. Do not force the workpiece against the blade; NEVER cut more than one piece at a time. DO NOT STACK more than one workpiece on the saw table at a time. , NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. AVOID CUTTING NAILS. Inspect for and remove all.nails from lumber before cutting. m NEVER TOUCH BLADE or other moving pads during use. DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION. STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are Ured. Do not rush. NEVER START A TOOL WHEN THE BLADE IS IN CONTACT WITH THE WORKPIECE. ALLOW THE MOTOR TO COME UP TO FULL SPEED before starting a cut. M MAKE SURE THE WORK AREA HAS AMPLE LIGHTING to see the work and that no obstruc- FIRMLY CLAMP OR BOLT your band saw to a firm, level workbench or table. The most comfortable saw table height is 36 inches or at approximately hip height. • AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance. ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when reconnecting to power supply. NEVER leave the band saw unattended while connected to a power source. • SAVE THESE INSTRUCTIONS. tions will interfere with safe operation BEFORE performing any work using your saw. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also. SAVE THESE INSTRUCTIONS 5 EXTENSION GROUNDING CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used. Length of Extension Cord In the event of a malfunction or breakdown, grounding provides a path of least resistance for electdc current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local cedes and ordinances. Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipmentgrounding conductor can result in a dsk of electdc shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grcunding conductor to a live terminal. Wire Size (A.W.G.) Up to 25 feet 18 26-100 feet 16 When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters WA on the cord's jacket. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation. _i, CAUTION: Keep the cord away from the cutting area and position the cord so that it will not be caught on lumber, tools, or other objects during cutting operations. ELECTRICAL INSTRUCTIONS Repair or replace a damaged or worn cord immediately. This tool is intended for use on a cimuit that has an outlet like the one shown in Figure 1. It also has a grounding pin like the one shown. CONNECTION Your Sears Craftsman Band Saw is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the saw does not operate when plugged into an outlet, double check the power supply. @ GROUNDING PIN COVEROFGROUNDED OUTLETBOX Fig. 1 6 BevelCut Acuttingoperationmadewithanangledtable. Resaw A cuffing operation to reduce the thickness of the workpiece to make thinner pieces. Crosscut A cutting operation made across the grain or the width of the workpiece. Resin Compound Cut Ripping A cutting operation along the length of the workpiece. A sticky, sap base substance. A compound cut is a cut made using a miter angle and a bevel angle at the same time. Saw Blade Path FPM The area directly in line -- over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be, or has been, cut by the blade. "Feet per minute. Used in reference to surface speed of blade. Sat Freehand (for band saw) Performing a cut without the workpiece propedy supported on the table. Thedistance that the tip of the saw b ada tooth s bent (or sat) outward from the face of the blade. Gum The matedal removed by the blade in a through cut or the slot produced by the blade in a nonthrough or partial cut. Throw-Back Throwing of a workpiece in a manner similar to a kickback. Usually associated with a cause other than the kerf closing, such as a workpiece being dropped into the blade, or being carelessly placed in contact with the blade. Leading End The end of the workpiece pushed into the cutting tool first. Through Sawing Any cutting operation where the blade extends completely through the workpiece. Miter Cut A cutting operation made with the edge of the workpiece at any angle to the blade other than 90 degrees. Workpiece The item on which the cutting operation is being done. The surfaces of a workpiece are commonly referred to as faces, ends, and edges. Push Stick Worktable A device used to feed the workpiece through the saw blade during narrow cutting operations. It helps keep the operator's hands well away from the blade. The surface on which the workpiece rests while performing a cutting operation. Blade Width Table Tilt A sticky, sap based residue from wood products. Kerf Blade Length 1/8 in. to 3/8 in. 59-1/4 in. Input Capacities: Frame to Blade Under guide Table Size No Load Speed 9 in. Overall Dimensions 3-1/2 in. Net Weight 11-1/2 in. x 11-1/2 in. 7 0" - 45" 120 V, 2.5 amp 60 Hz, AC only 3000 FPM 19-1/2 in. x 12-1/2 in. x28 in. 30 Ibs. ,_ • WARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts to your saw before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. _ WARNING: If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. • Do not discard the packing materials until you have carefully inspectedthe saw, identified all parts, and satisfactorily Operated your new saw. Carefully remove all parts from the carton and place the saw on a level work surface. Separate and check against the list of loose parts. Note: If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or miss(ng parts are obtained and are installed correctly. Check all loose parts from the box with the list below. For your convienence when identifying parts, items A-I below have been drawn actual size. Assemble according to the instructions on the following pages. A. Flat Head Screw (1/4-20 x 7/8 in.) ..................... 3 B. Hex Nut (1/4-20) ................................................. 3 C. 1 Switch Key .......................................................... D. Truss Head Screw (1/4-20 x 5/8 in.) .................. 1 E. Wing Nut (1/4-20) ............................................... 1 F. Screw (M5 x 8) ................................................... 1 G. Scale Indicator .................................................... 1 H. Throat Plate ........................................................ 1 I, Hex Key (1/8in.) ................................................. 1 J. Saw Table (not shown) ...................................... t K. Owner's Manual (not shown) ............................ on0 t L Fig. 2 The following tools (not included) are needed for assembly and alignment: _ • #2 Phillips Screwddver • Adjustable Wrench #2 PHILLIPSSCREWDRIVER • Small Combination Square SMALL COMBINATION SQUARE Fig. 3 8 A. A WARNING/ ADVERTENCIA Blade 59 1/4in. B. C= Blade Thickness TPI Application .018in, 15 Forfinescrollcuts inthinwoodmathdalsand plasticsUpto 1/2" thick. 59 114in. .012in. 4 ForextrafaststralgMcutting, Bestfor cuttingthickwoods, 591/4 in. .012in. 6 Forsb'algMandcurved 59 1/4 in. ,014in. 4 Heavydutycuts in all wood 3/4" to 3 1/2" Fig. 4 9 The following labels are on the band saw with locations indicated. El &WARNING ;IA • For your safety, read owner's manual before making adjustment_ • Failure to remove switch key and unplug your saw could result In acaldental starting causing possible sedous personal Injury. • Para su eagurldad, lea el manual del usuado antes de hacar aJustos. FI 9 inch Band Saw GI 3000FPM120VOLTS60 HzACONLY WARNING: USEIOEk'rlCAL REPI.ACEaEm'PAR'rs. (_ MODEL 315,214490 SER, NO. MADE _1TAIWAN SEARS, ROEBUCK AND CO, Customer i I i _Jmo_'mot. Help Line 1-800-932-3188 Fig. lO KNOWYOURBAND SAW Beforeattempting to use,familiarizeyourselfwithall TENSION BLADE The saw comeswitha standard1/4 in. bladeinstalled. GUIDES Blade guides support the blade and keep it from twisting dudng operation. An adjustment is necessary when blades are changed or replaced. BLADE GUIDE LOCK KNOB AND LOCK LEVER SCREW EXHAUST PORT A standard 2-1/4 in. dust exhaust port has been provided to make dustless cutting possible.The pickup adapter end of a vacuum hose fits inside the dust exhaust port with a wedge fit type connection. KNOB ADJUSTMENT ADJUSTMENT Tracking adjustment screw adjusts to keep the blade running in the center of the wheels. It is a set screw located in the center of the frame on the back of your band saw. SAWDUST Loosening table lock knob allows table to be tilted at different angles. Tightening knob locks table in place. ANGLE TRACKING BAND SAW TABLE Your band saw has an 11-I12 in. square, aluminum saw table with a rack and pinion tilt control for maximum accuracy. It has a red snap in throat plate, and a miter slot for use with an optional miter gage. The blade guide assembly should just clear the workpiece while cutting. Use the blade guide knob and lock lever to adjust the blade guide assembly to keep the blade from twisting or breaking. Always lock the upper blade guide assembly in place before turning on the band saw. TABLE KNOB The tension adjustment knob controls the amount of blade tension when changing blades and when making adjustments for vadous sawing applications. operating features and safety requirements of your Sears Craftsman band saw. BLADE ADJUSTMENT COVER TABS Easy open cover tabs allow the front cover to be opened for making adjustments. KNOB Once the table lock knob has been loosened, use the angle adjustment knob to tilt or change the angle of the table. Always tighten the table lock knob before turning on the saw. HEX KEY HOLDER A hex key holder inside the front cover keeps hex key conveniently located for blade guide and blade tracking adjustments. SCALE SWITCH The scale shows the angle or degree the table is tilted for bevel cutting. Your band saw has an easy access power switch. To lock the switch in the OFF position, remove the yellow switch key from the switch. Place the key in a location that is inaccessible to children and others not qualified to use the tool. BACK VIEW OF BAND SAW QUICK RELEASE ADJUSTMENT KNOB FRONTCOVER COVERTAB LOCK LEVER_ ADJUSTMENT SCREW BLADEGUIDE KNOB BLADEGUIDE ASSEMBLY SAW BLADE BLADEGUIDE ASSEMBLY THROAT PLATE' TABLE LOCK SWITCHKEY EXHAUST PORT BANDSAW TABLE Fig. 6 DATAPLATE 11 m l INSTALLING SCALE INDICATOR Align the three holes on the table with the three holes in the angle bracket. Fasten the table to the angle bracket using the three flat head screws and three hex nuts. See Figure 7. • Attach the scale indicator to the saw frame below the scale using the screw (M5 x 8) supplied. • ANGLEADJUSTMENTKNOB Assemble the truss head screw and wing nut to the edge of the table at the end of the slot. Snap the throat plate in place on the table. Note: The wing nut goes below the table. MOUNTING BAND SAW TO WORKBENCH See Figure 9. If the band saw is to be used in a permanent application, we recommend that you secure it in a permanent location such as a workbench. When mounting the saw to a workbench, holes should be ddlled through the supporting surface of the workbench using the dimensions illustrated in figure 9. • ANGLEBRACKET SCALEINDICATOR TABLELOCKKNOB SCALE Fig. 7 INSTALLING THE TABLE • • Drill (4) 3/8 in. diameter holes through workbench. • Place band saw on workbench aligning holes in the frame with holes drilled in the workbench. • Insert all four 5/16 in. screws and tighten securely with lock washers and hex nuts. See Figure 8. • Slide the table onto the angle bracket from the back of the saw to front, with the blade traveling through the slot in the table. Each leg should be bolted securely using 5/16 in. diameter machine screws, lock washers, and 5/16 in. hex nuts (not included). Screw length should be 1-3/4 in. plus the thickness of the workbench top. Locate and mark the holes where band saw is to be mounted. Note: All bolts should be inserted from the top. Install the lock washers and hex nuts from the underside of the bench. TRUSSHEAD SCREW Supporting surface where band saw is mounted should be examined carefully after mounting to insure that no movement during use can result, If any tipping or walking is noted, secure workbench or supporting surface before beginning cutting operations. FLAT HEAD SCREW(S) 3-13/32in. I _NGLE BRACKET 5-15/16in. e 318 in. I hole I /, HEX NUT(S) 12 in. 3-I/32in. _L 3-I 3/32in. 3-13/32In, Fig. 9 Fig. 8 12 CLAMPING BAND SAW TO WORKBENCH in the saw frame, material being mounted to, lock washers, and hex nuts. See Figure 10. Note: It may be necessary to countersink hex nuts and washers on bottom side of mounting board. If the band saw is to be used in a portable application, we recommend that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use. Any good grade plywood or chipboard with a 3/4 in. thickness is recommended. Mount saw to board using holes in frame as a template for hole pattern or the diagram in Figure 9. Locate and mark the holes where band saw is to be mounted. • MOUNTING BOARD " Follow last three steps in previous section called Mounting Band Saw to Workbench. If lag bolts are used, make sure they are long enough to go through holes in the saw and material the saw is being mounted to. If machine bolts are being used, make sure bolts are long enough to go through holes ADJUSTING BLADE See Figures 11 and 12. GUIDE C-CLAMP(S) ASSEMBLY • Push the lock lever that secures the blade guide assembly counterclockwise or to the left 1/4 turn to unlock the blade guide assembly. • Lock position in place by returning the lock lever to its upward position. • Always lock the blade guide assembly in place before turning on the band saw. BLADEGUIDEKNOB LOCKLEVER Rotate the blade guide knob to position the blade guide assembly to the desired position. Use a scrap piece of the same wood you are about to LOCKLEVER (UNLOCKEDPOSITION) Fig. 10 cut as a guide to set the height of the blade guide assembly. The blade guide assembly should always be set about 1/8 in. above the top surface of the workpiece being cut to keep the blade from twisting or breaking. Adjust from the back of the band saw. • WORKBENCH POSITION) BLADEI BLADEGUIDEKNOB k I WORKPIECE ® Fig. 11 Fig. 12 13 INSTALLING BLADE AND ADJUSTING THE • Turn the quick release knob to the left to release blade tension. Turn the tension adjusting knob to the left to lower the upper _'heal. See page 15. • Carefully remove the old blade. The spring on the upper wheel allows it to be pulled down slightly to remove the saw blade from the wheel. Slide the new blade into the slot of the table with the teeth of the blade toward the front of the saw See Figures 13 and 14. A • WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before installing or removing blade. • From the back of the saw, push the lock lever counterclockwise or to the left 1/4 turn to unlock Note: The blade may need to be tumed inside out if the teeth are pointing in the wrong direction. Hold the blade with both hands and rotate it inward. the blade guide assembly. Use the blade guide knob to position the blade guide assembly about half way between the table and the frame. Return the lock lever to its upright locked position. See Figures 11 and 12. • Open the front cover of the saw by pushing both the upper and lower cover tabs. See Figure 6. • Loosen and remove the wing nut and truss head screw from the table. See Figure 13. BLADEGUARD/ and facing down toward the table. Place the blade through the lower blade guides located under the table and around the lower wheel. Pull down on the upper wheel slightly to place the saw blade on the wheel. Slowly turn the upper wheel to the right or clockwise by hand to center the blade on the rubber tires. • Adjust the blade tension and check or adjust the blade tracking. See pages 15 and 16. • Adjust both upper and lower blade guides and thrust bearings. See pages 16 and 17. • Replace the truss head screw and wing nut. Tighten securely. • Close the cover of the band saw. BANDSAW TENSIONADJUSTINGKNOB TRUSSHEAD SCREW FRONTCOVER , OPEN UPPER ;AWBLADE BLADEGUIDE WINGNUT _i, Fig. 13 WARNING: Always wear safety goggles or safety glasses with side shields to protect your eyes while uncoiling band saw blades. Failure to heed this warning could result in a serious eye injury. GUIDES Wearing gloves, carefully uncoil the blade at arms length. If the new blade was oiled to prevent rusting, it may need to be wiped to keep the oil from your workplace. Carefully wipe in the same direction the teeth are pointing so the rag does not catch on the teeth of the saw blade. LOWER WHEEL Fig. 14 14 ADJUSTING BLADE TENSION QUICKRELEASEKNOB See Figures 15, 16, and 17. • Turn off saw, remove switch key and unplug saw. _1, WARNING: Failure to remove switch key and unplug your saw could result in accidental starting causing possible serious personal injury. TO ENGAGE The tension adjusting knob is on the top of the saw, Rotate the quick release knob (outer, larger knOb) 114 tum to the left or counterclockwise to release blade tension. See Figure 15. Fig/17 Another method of checking the tension has to do with the sound the blade makes when plucked like a guitar string. QUICKRELEASEKNOB Pluck the back straight edge on the coasting side opposite the blade guides while turning the tension knob. Sound should be a musical note. Sound becomes less flat as tension increases. Sound decreases with too much tension. TO RELEASE Using either method to check tension requires knowing your band saw and can be developed with practice. • Fig. 15 • Turn the tension adjusting knob (upper, smaller knob) to the right or clockwise to increase tension or raise the upper wheel. Turn it to the left or counterclockwise to decrease tension on Note: Be careful not to over tension the blade. Too much tension may cause the blade to break. Too little tension may cause the blade to slip on the wheels. blade or to lower upper wheel. See Figure 16. TRACKING Note: Adjustments of the blade tension can be made at anytime. The quick release knob can be either released or engaged while making adjustments with the tension adjusting knob. • Rotate the quick release knob to the right or clockwise 1/4 turn to engage tension before using the band saw. See Figure 17. • To check the tension, raise the blade guide assembly all the way up exposing the blade. • Pushing the blade to the side with moderate force, the blade should deflect approximately 1/8 in. THE BLADE See Figure 18. Note: Blade tension must be properly adjusted before tracking the blade. • Open the front cover of the saw. Slowly turn the upper wheel to the dght or clockwise by hand and watch the blade on the upper tire. If the blade moves away from the center of the tire, the tracking must be adjusted. TO ADJUST: TENSIONADJUSTINGKNOB TO INCREASE TENSION Never tension the blade so tight as to completely compress the spring. When completely compressed, the spdng can no longer act as a shock absorber. • Remove 118 in. hex key located in the holder inside the front cover. • Insert the 1/8 in. hex key into the tracking adjustment screw located on the back of the saw behind the upper wheel. If the blade moved toward the front of the saw " turn the adjustment screw in (to the right or clockwise) while turning the wheel by hand, until the blade moves back and rides in the center of the tire. TO DECREASE TENSION If the blade moved away from the front of the saw, tum the adjustment screw out (to the left or counterclockwise) while turning the wheel by hand, until the blade moves forward and ddes in the center of the tire. Fig. 16 15 Check the position of the blade on the lower tire. The blade should be completely on the tire. If not, adjust the tracking until the blade is on both tires. • • Tighten the table lock knob. • Rotate the upper wheel by hand in a clockwise direction for a few more turns. Make sure the blade stays in the same location on the tires. Readjust if necessary, until blade is tracking properly. Using the 118 in. hex key, adjust the zero stop set screw until the set screw just touches the frame. Check squareness of table to blade. Make readjustments if necessary. Loosen screw on scale indicator and align red mark to zero on scale. See Figure 7, page 12. Note: The 1/8 in. blade may not track propedy in the center of the wheel. It may be better to track this blade on the back half of the upper wheel. • Rotate angle adjustment knob to tilt the table up or down to align table 90" to blade (0" position). Tighten all screws securely. Replace hex key in holder located inside of the front cover. Close front cover. BLADEGUIDE KNOB BLADEGUIDE ASSEMBLY BLADEON SMALL ZERO STOP SETSCREW SQUARE TURN HEXKEY TO LEFT (1/8in.) TURN HEXKEY TO RIGHT ALIGNING BLADE Fig. 19 Fig. 18 THE TABLE SQUARE ADJUSTING TO THE BEARINGS, BLADE BLADE GUIDES The upper and lower blade guides and tl_rustbearings support the band saw blade during cutting operations. The adjustment of the guides and bearings should be checked whenever a different blade is installed. See Figure 19. _1_ WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before making adjustments. WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before making adjustments. m:- - From the back of the saw, push the lock lever counterclockwise or to the left 1/4 turn to unlock the blade guide assembly. See Figure 11, page 13. To Adjust • • • THRUST GUIDE SUPPORT, AND See Figures 20, 21_ and22. Rotate the blade guide knob to move the blade guide assembly all the way up. Return lock lever to the upward position to lock assembly in place. Thrust •earings Adjust the thrust bearings first. Using the 1/8 in. hex key, loosen the thrust bearing screw. Note: The thrust b_aring screw is the upper cap screw located on the right side of the blade guide assembly. It is the lower cap screw on the right side of the frame below the table for the lower bearing. Loosen table lock knob. See Figure 7, page 12. Place a small combination square on table beside blade. 16 BLADEGUARDREMOVED FOR CLARIRCATIONONLY BLADEGUIDE BLADE SCREW • THRUSTBEARING SCREW BLADEGUIDE SCREWS BLADEGUIDE SUPPORTSCREW rHRUBTBEARING LOWERBLADEGUIDE Fig. 21 To Adjust BLADEGUIDESCREWS Fig. 20 Move the thrust bearing to within 1/64 in. of the blade. Tighten the thrust bearing screw securely. Repeat this procedure on the lower thrust bearing, located below the table. • Loosen the two blade guide screws that lock the upper blade guides. Press the two guides evenly near the sides of the blade leaving about 0.004 in. from the blade. (0.004 is the thickness of a dollar bill.) Do not pinch the blade. Make sure one guide is not further away from the blade than the other. Release the guides and tighten both screws securely. • Repeat this procedure on the lower blade guides located under the table. See Figure 21. Note: The thrust bearing is to support the back edge of the blade while cutting. The blade should not contact the bearings when you stop cutting. It is important that both thrust bearings be adjusted equally. TO Adjust Blade Guide Support • Next, adjust the position of the blade guide support. Loosen the bottom screw on the right side of the blade assembly using the hex key. • Slide the blade guide support on the shaft until the front edge of the blade guides are about 1/64 in. behind the gullet of the blade, Tighten the screw securely. Repeat this procedure for the lower blade guide support. BLADEGUARDREMOVED FOR CLARIRCATIONONLY Note: The lower blade guide support screw is the top screw located on the right of the saw frame under the table. See Figure 21. _,i_ Guides The blade guides help keep the blade from twisting and binding. Letting the blade teeth hit the blade guides while using the band saw will ruin the blade. The set of teeth and the sharpened edge of teeth will be damaged by hitting the blade guides, Proper adjustment of the upper and lower blade guides will prevent this from happening. BLADE GUIDEASSEMBLY • Blade , THRUST BEARING WARNING: Never operate saw without blade guard secured !n place. To do so could result in possible serious personal injury. BEARINGSCREW BLADEGUIDE SCREW 3UIDE SCREW BLADEGUIDES Fig. 22 17 BASIC OPERATION OF THE BAND Turn saw off, remove switch key, and unplug cord before moving the saw. SAW A band saw is basically a "curve cutting" machine. It can also be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, compound cutting, and resawing. It is not capable of making inside or non through cuts. Avoid injury from jams, slips or thrown pieces: • Choose right size and style blade for material and the type of cut you plan to do. • USE ONLY RECOMMENDED ACCESSORIES, This band saw is designed to cut wood and wood composition products only. The use of improper accessories may cause risk of injury to persons. For general type scroll cutting, follow the pattem lines by pushing and tuming the workpiece at the same time. Do not try to tum the workpiece while engaged in the blade without pushing it; the workpieca could bind or twist the blade. A curved radius cut is best performed by following the pattern line with the blade while turning the workpiece. The blade should cut in the middle of the pattam line since wood cutting band saw blades are thin. _i, Make sure blade guides and thrust bearings are properly adjusted. • Always adjust the blade guide assembly to just clear the workpiece to avoid accidental blade contact, minimize blade breakage and provide maximum blade support. Use extra caution with large, very small or awkward workpleces: Use both hands while feeding the work into the blade. Hold the workpiece firmly against the table. Use gentle pressure. Do not force the work, but allow the blade to cut. Use extra supports (tables, saw horses, blocks, etc.) Never use a person as a substitute for a table extension, or as additional support for a workpiece that is longer or wider than the basic saw table, or to help feed, support or pull the workpiece. The smallest diameter circle that can be cut out is determined by the width of the blade. A 1/4 in. wide blade will cut a minimum diameter of approximately 1-1/2 in. A 1/8 in. wide blade will cut a minimum diameter of approximately 1/2 in. When cutting irregularly shaped workpieces, plan YoUr work so it wil! not pinch the blade. For example, a piece of molding must lay flat on the table. Workpieces must not twist, rock, or slip while being cut. Relief cuts are made when an intricate curve (too small a radius for the blade) is to be cut. A relief cut is made by cutting through the scrap section of workpiece to curve in pattern line, then carefully backing blade out. Several relief cuts should be made for intricate curves, then follow pattern line as sections are cut off of curve =relieving" blade pressure. Properly support round material such as dowel rods, or tubing. They have a tendency to roll during a cut, causing the blade to "bite." To avoid this, always use a "V" block or clamp workpiece to a miter gage. Avoid injury from unexpected saw movement: • Put the saw on a firm level surface with plenty of room for handling and properly supporting the workpiece. % Make sure table is level and saw does not rock. • • • Make sure table lock knob is tight and no parts have excessive play. Failureto do so couldresultin seriouspersonal injury. • Make sure the blade teeth point downward, toward the table. • Make sure blade tension is properly adjusted. WARNING: To avoid blade contact, adjust the blade guide assembly to just clear the workpiece. M • Cut only one workpiece at a time. Clear everything except the workpiece and related support devices off the table before turning the saw on. Bolt the saw tothe support surface to prevent slipping, walking or eliding during operations like cutting long, heavy boards. 18 When backing up the workplece, the blade may bind In the kerf (cut), This is usually caused by sawdust clogging up the kerf or because the blade comes out of the guides. If this happens: Plan the way you will hold the workplece from start to finish: Do not hand hold pieces so small that your fingers will go under the blade guard. Keep your hands away from the blade. • Turn switch OFF. Avoid awkward operations and hand positions where a sudden slip could cause serious injury from contact with the blade. Never place hands in path of blade. A • • Wait for all moving parts to stop. • Remove switch key. • Unplug the saw. WARNING: Do not allow familiarity with your saw make you careless. Remember that a careless fraction of a second is sufficient to inflict • Open band saw cover. • Wedge the kerf open with a flat blade screwdriver or wooden wedge. severe injury. • Turn the upper wheel by hand while backing up the workpiece. When saw Is running: • • Before removing loose pieces from the table, turn saw off and walt for all moving parts to stop. Before starting your cut, watch the saw while it runs. If you experience excessive vibration or unusual noise, stop immediately. Tum the saw off, and remove switch key. Unplug the saw. Do not restart until locating and correcting problem. Before leaving the saw: Wait for all moving parts to stop. Remove the switch key. Store it away from children and others not qualified to use the tool. Before freeing any jammed materlah • Turn switch OFF. • Wait for all moving parts to stop. • Remove switch key. • Unplug the saw. 19 • Unplug the saw. • Make workshop child-proof. Lock the shop. _1, WARNING: When servicing, use only identical Craftsman r(_placement parts. Use of any other part may create a hazard or cause product damage. GENERAL MAINTENANCE BLADE • The blade guides may become rounded and worn during use. Remove the blade guides and file or grind flat. • Replace the guides when filing or grinding has worn down guides and they can no longer be properly secured in place. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. _L GUIDES See Figure 22, on page 17. MOTOR/ELECTRICAL WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. • Frequently vacuum or blow out any sawdust from the motor. & WARNING: If the power cord is worn, cut, or damaged in any way, have it replaced immediately by a qualified service technician at a Sears store. Failure to do so could result in serious personal injury. • Keep your band saw clean. • Remove sawdust from the inside frequently. • Do not allow pitch to accumulate on the table, blade guides, or thrust bearings. Clean them with gum and pitch remover. • Apply a thin coat of automobile type wax to the table top so the wood slides easily while cutting. Also apply wax to the inside surfaces of the angle bracket. A n BRUSHES See Figures 23 and 24. A WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before working on the band saw. WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before working on the band saw. There are two brushes located inside the saw's cover, one next to each wheel. They help protect the tires and wheels by brushing off saw dust. As the brushes become worn, they will need to be adjusted or replaced. • Loosen the screw to slide the rorush and holder TIRES To properly and safely maintain the wheel tires, the blade should be removed from the band saw. The tires should be kept clean. When the tires become worn they should be replaced. • Pitch and sawdust that accumulates on the tires should be removed with a fine wire brush or a piece of wood. Do not use a sharp knife or any kind of solvent. • WARNING: To avoid fire or electrocution, reassemble electric parts with only identical Craftsman replacement parts. Reassemble exactly as originally assembled. toward the wheel. The brush should just touch the wheel. SCREW LOWERWHEEL BRUSH Remove the blade guard, the saw blade, and the worn tires. Stretch the new tires around each wheel. Fig. 23 20 l Carefully pull the brush straight off of the brush holder to replace the brush. Push the new brush on the holder until you hear it snap in place. • Remove the screw to replace both brush and holder. BRUSHHOLDER • Place new drive belt on the pulley. As you return pulley to pulley shaft, place drive belt over motor pulley. Position the pulley on the raised portion of the pulley shaft. • Return the wheel to the pulley shaft. For correct orientation of wheel, notice that the screw holes on the wheel ere all in recessed areas. These BRUSH must align with the screw holes on the pulley. • Replace the screws and tighten to secure wheel. Put the shim (washer) and retaining ring back on the pulley shaft. Replace the saw blade. Check thrust bearings and blade guides. LOWERWHEEL PULLEYSHAFT RETAININGRING Fig. 24 DRIVE BELT SCREW(S) See Figure 25. _1 SHIM (WASHER) WARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw, remove the switch key, and unplug the saw before working on the band saw. MOTORPULLEY DRIVEBELT PULLEY Fig. 25 Due to wear or breakage, the drive belt may need to be replaced. The drive belt is located behind the lower wheel of the band saw. • Remove the saw blade and set it aside. See section on Installing and Adjusting Saw Blade. • Using retaining ring pliers, remove the retaining ring from the lower wheel. • Remove the shim (washer). • Remove the 3 screws in the wheel and slide the wheel off of the pulley shaft. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. I1._ Remove the pulley and worn drive belt. 21 ,_1= WARNING: For your own safety, turn switch Off, remove switch key and unplug the saw from power supply before adjusting or aligning your band saw. PROBLEM CAUSE SOLUTION Motor will not run. 1. Problem with On-Off switch or 1. Have worn parts replaced before using Band Saw again. power cord. 2. Motor Defective. 2. Do not attempt any repair. Have repaired by a qualified service technician st a Sears store. Blade does not run in the approximate center of the upper wheel. 1. Not tracking properly. 1. Adjust tracking, See Adjustments section Tracking the Blade. Band Saw slows down when 1. Cutting too small a radius. . cutting. Blades breaking. Saw is noisy when running. Blade will not cut straight. Blade guides will not stay in position. Stop feeding, and back up the material slightly, until the band saw speeds up. 2. Dull blade. 2. Replace blade. 1, Too much tension. 1. Adjust tension. See Adjustments section Adjusting Blade Tension. 2. Kink in blade caused by cutting too small a radius or turning the material too fast when cutting. 2. Use correct cutting technique. See section Basic Operation of the Band Saw. 3. Thrust bearings scarred or not rotating. 3. Replace the thrust bearings. 1. Too much blade tension. 1, Adjust blade tension. See Adjustments section Adjusting Blade Tension. Adjust upper and lower blade guides and bearings. See Adjustments section Adjusting Thrust Bearings, Blade Guide Support, and Blade Guides. 2. Blade guides and backup bearings are in contact with the blade. 2. 1. Blade guides and bearings not properly adjusted. 1. 2. Worn or defective blade. 2. Replace blade. 1. Blade guide screws have loosened. 1. Tighten blade guide screws securely. 22 Adjust upper and lower blade guides and bearings. See Adjustments section Adjusting Thrust Bearings, Blade Guide Support, and Blade Guides. 23 CRAFTSMAN I BAND SAW - MODEL NO. 315.214490 The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your BAND SAW or when ordering repair parts. 4 | J 5 i 4 I $ $ 2 19 1 7 18 17 14 9 20 10 13 12 FIGURE A 24 CRAFTSMAN I BAND SAW - MODEL NO. 315.214490 I The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your BAND SAW or when ordering repair parts, SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST FOR FIGURE A Key No. Part Number Description 1 STD541610 ** 2 977095-001 3 977079-001 4 Quan. Wing Nut (1/4-20) ................................................................. 1 * Screw (1/4-20 x 3/4 in. Truss Hd.) ....................................... 1 * Screw (1/4-20 x 5/8 in. Socket Hd.) ..................................... 1 977085-001 Screw (1/4-20 x 7/8 in. Flat Hd.) .......................................... 3 5 977027-001 Throat Plate ......................................................................... 1 6 977028-001 Table ..................................................................................... 1 7 977030-001 Table Lock Knob .................................................................. 1 8 977092-001 Washer ................................................................................. 1 9 977031-001 Spindle ................................................................................. 1 10 977093-001 Washer (Shim) ..................................................................... 1 11 977086-001 Scale .................................................................................... 1 12 STD541025 Hex Nut (1/4-20) .................................................................. 3 13 977033-001 Angle Adjustment Shaft ....................................................... 1 14 977032-001 Angle Bracket ....................................................................... 1 15 977105-001 Washer (Shim) ..................................................................... 1 16 977029-001 Angle Adjustment Knob ....................................................... 1 17 977065-001 Spring ................................................................................... 1 18 977087-001 Washer (M6) ........................................................................ 1 19 977088-001 Retaining Ring ..................................................................... 1 20 820193-005 Hex Key 1/8 in. (Item No. 9-28135) ..................................... 1 ** * * Standard Hardware Item - May Be Purchased Locally ** Available From Division 98 - Source 980.00 25 CRAFTSMAN BAND SAW - MODEL NO. 315.214490 [ The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your BAND SAW or when ordering repair parts. 2 I 2 9 7 SEE NOTE"A"PAGE27 FIGURE B 26 I CRAFTSMAN I BAND SAW - MODEL NO. 315.214490 J numberin correspondenceregarding your BAND SAWthe or when orderingrepairparts. The modelallnumberwill be found on a plate attachedto frame. Always mentionthe model i, PARTS LIST FOR FIGURE B Key No. Part Number Description 1 977084-001 Cover Plate ............................................................................. 1 2 977083-001 Screw (M4 x 8 Pan Hd.) .......................................................... 7 3 977056-001 Cord ........................................................................................ 2 4 STD551208 5 977082-001 Cord Clamp ............................................................................. 1 6 977056-001 Conden,sor............................................................................... 1 7 STD51008 ** Washer (M8) ........................................................................... 2 8 STD52008 ** Spring Washer (M8) ................................................................ 2 9 STD835020 ** Hex Bolt (MS x 1.25 x 20) ....................................................... 2 10 977367-001 Motor ....................................................................................... 1 11 977045-001 Motor Pulley ............................................................................ 3 * ** Washer (M4) ................................................................ Quan. :.......... 1 NOTE: "A" - The assembly shown represents an Important part of the Electrical System. To avoid the possibility of alteration or damage to the System, service should be performed by your nearest Sears Repair Center. Contact your nearest Sears Retail Store for Service Center information. * Standard Hardware Item -- May Be Purchased Locally ** Available From Division 98 - Source 980.00 J_ 27 o o 28 ii!iiiiiiiiiiiiiii iil iiiiiiii -r : : : : : : : : : : : : : : : : : .£._ : x _ : _ : : : : : : : : : :_oc_ : :-r-_. : : : : : : : • : : : : : _ : : _d_ • . _ ._oe_ " = . .... . A _ _ _ ........ TOO ° _ : :_ • : i _ .:0 _ :" _ C _ ®0 _" x _ •_ X: _¢D"0 _ "0 e : _ __D7_ _ "_ 0 _tO u)_ ,_-- LO 0 u_ ,.Z ,_ _ __ • C_ _ _ CO _ _. "-t_ ,^ _ _x _D _D :_ " ,-"0 - : •_x "0 >_ __ _-_ . _ . D _ _ . 0 __ __E " z vZ 0 88OoOoOOOOOOo oo ooooooooooooooo. o ..... 99ooooooooooooooo 99 ooooooo2ooooo __t,:.r,-.t-._._ ooo o o rrprppoooooooo_m_ t--r--t,-t,-_t,.r,.r,-_-.r-r,-r-._t,.t.._ot.. _ _ _ _ _ _ o _ _ _ _ _ _ _ _0 c_ o _- _ _,_ m _ _ _0 m o _- _ _0,_ u_ 1/) IZ o _. : ,c : : : : : : : : : : : : : : • :_ :_ :_ :!_ : _=_ ! : _ : __ • • •-- • . _ " _E : :! :! : _ : : : :! !: := : : : _ _ : : : : : : : : : : : : : : : : :A _ : :_. : : : : : : :T -r : : : : : : : m = m _ _ _ _ ! : _ : :aO :x: : : : : N'_ • : : : _ _ _= : : : " c . ..... _ t_ c A : : ..... 0 -_ .... : e m_ ! ! _0 o z_ : :E _,m m_ :® m_ _ _n-_ m _ ®= _ ® m_ •.- ,___ _:.=_._o 0 0 _ _ o_.- o _ _ _ _ C_ _ "_ "E ® ®_ _ !__mu_-- ..... _ : : : : : : ! -_ _ ' _-_ : : : : u_ _-- _ _ " _ !_ . _- : i i !_--'_,- _ : " m ® - o _, -= 0 __ _ 0 _ _ _ _._ _ _ ___ c_ c_ o c_ o_ _.> ._ _ _ o _ o _ _ SSSSS_SSSSSooSSSSSoo_SS_ooS_SSS °°°°°°°°°°°°°°°°°°°°_°_i°°°°°°°°©' , , , _,. _o_o_oo_Sg 29 _°o_ _.,, _88o o_ °i 3 no 30 i • 81 iii iiiiiii iii ...... • .... *°,. .... ....... • ,,...**.. ,. ..... * . I .... .... . . ..... ° *,, * . . ..... .......... ii i i i i ! i i i i i i i i i i i i i 0 5 • * ........ * . . . • * ........ ........ o . . . * . * , . ....... o * . . . . . . * , , . . , , . , * * . . . , , . -i- : : : : : : : : : : u. I II (0 : : : : : : cn i "0 9_ i _ '_ .m '_ _ _ _,._ ._ _ _ _ .-° E _ _ ._ _ _ _ • I- nq m m ..a m _o .a o_ m m m _ 0 : _ 000_ _oo_ _ _ _ _ _ _ _ _'_ 81 ooo_o _ _ _ 0 i. -_, Forthe repairor replacementpartsyouneed delivereddirectlyto yourhome Call7 am - 7 pm, 7 daysa week 1-800-366-PART (1-800-366-7278) Forrepairservice Call24 hoursa day,7 daysa week 1-800-4-REPAIR (1-800-473-7247) For the location of a SearsPartsandRepairCenterin yourarea Call 24 hours a day,7 daysa week 1-800-488-1222 The modelnumberof thistool will be foundon a serial plate attachedto the motorhousing.When requestingserviceor orderingparts, always providethe followinginformation: • ProductName 9 in. BandSaw • Model Number 315.214490 • Part Name • Part Number mmmmmm mmmmmm SEARS America's Repair Specialists
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 32 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Sat Sep 29 14:14:35 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools