Craftsman 646 1062 Users Manual

CRAFTSMAN Buffer/polisher Manual L0070081 CRAFTSMAN Buffer/polisher Owner's Manual, CRAFTSMAN Buffer/polisher installation guides

6461062 77746672-a325-4d2b-9b4d-07922a732e1f Craftsman Sander 646.1062 User Guide |

: Craftsman Craftsman-646-1062-Users-Manual-161053 craftsman-646-1062-users-manual-161053 craftsman pdf

Open the PDF directly: View PDF .
Page Count: 8

Owner's Manual

ICRRFTSMRN°I

Double Insulated

BUFFER/POLISHER SYSTEM

Model No. 646.10620

®

CAUTION:

Read and follow all safety

rules and operating

instructions before first

use of this product.

• Safety

• Accessories

• Operation

• Maintenance

• Parts

• Espadol

Save this manual for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit our Craftsman website: www.sears.com/craftsman

_ib _j/_ WARNING: Read and

understand all instructions.

Failure to follow all instructions listed

below may result in electric shock, fire

and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

WORK AREA

PERSONALSAFETY

•Keep your work area clean and well lit. •

Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the •

dust or fumes.

•Keep bystanders, children, and visitors

away while operating a power tool.

Distractions can cause you to lose

control. •

ELECTRICAL SAFETY

•Double insulated tools are equipped with

apolarized plug (one blade is wider than

the other.) This plug will fit in a polarized

extension cord only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a

qualified electrician to install a polarized

outlet. Do not change the plug In any

way. Double insulation [] eliminates the

need for the three-wire grounded power

cord and grounded power supply system.

• Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your

body is grounded.

•Don't expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

•Do not abuse the cord. Never use the

cord to carry the tools or pull the plug

from an outlet. Keep cord away from

heat, oil, sharp edges or moving parts.

Replace damaged cords immediately.

Damaged cords increase the risk of

electric shock.

•When operating a power tool outside, use

an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor

use and reduce the risk of electdc shock.

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication. A moment of inattention

while operating power tools may result in

serious personal injury.

Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves

away from moving parts. Loose clothes,

jewelry, or long hair can be caught in

moving parts.

Avoid accidental starting. Be sure switch

is off before plugging in. Carrying tools

with your finger on the switch or

plugging in tools with the switch on

invites accidents.

Do not overreach. Keep proper footing

and balance at all times. Proper footing

and balance enables better control of

the tool in unexpected situations.

Usa safety equipment. Always wear eye

protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection

must be used for appropriate conditions.

TOOLUSEAND CARE

•Use clamps or other practical ways to

secure and support the workpiece to a

stable platform. Holding the work by

hand or against your body is unstable

and may lead to loss of control.

•Do not force tool. Use the correct tool for

your application. The correct tool will do

the job better and safer at the rate for

which it is designed.

•Do not use tool if switch does not turn it

on or off. Atool that cannot be controlled

with the switch is dangerous and must

be repaired.

•Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing the

tool. Such preventive safety measures

reduce the risk of starting the tool

accidentally.

2

TOOL USE AND CARE

• Store idle tools out of reach of children

and other untrained persons. Tools are

dangerous in the hands of untrained

users.

•Maintain tools with care. Properly

maintained tools are less likely to bind

and are easier to control.

•Check for misalignment or binding of

moving parts, breakage of parts, and

any other condition that may affect the

tool's operation. If damaged, have the

tool serviced before using. Many

accidents are caused by poorly

maintained tools.

Use only accessories that are

recommended by the manufacturer for

your model. Accessories that may be

suitable for one tool may create arisk of

injury when used on another tool,

SERVICE

• Tool service must be performed only by

qualified repair personnel. Service or

maintenance performed by unqualified

personnel may result in arisk of injury.

• When servicing a tool, use only identical

replacement parts. Follow instructions in

the maintenance section of this manual.

Use of unauthorized parts or failure to

follow maintenance instructions may

create a risk of electric shock or injury.

CARTON CONTENTS

• Storage Case

• Buffer/Polisher

•Terrycloth Bonnets (3)

•Wax Applicator Bonnets (5)

AVAILABLE ACCESSORIES

Item

Polishing bonnet (1)

Terrycloth bonnets (2)

Wax applicator bonnets (4)

Cleaner/Glaze (8 oz.)

Clear Pro TM Wax (8 oz.)

Wax(8 oz.)

Stock#

10604

10603

10609

10996

10995

10998

Before you begin, make sure your car is

clean and dry. The work area should be dry

also. If necessary, remove road tar with a

general cleaner before polishing. Also,

remove excess grease spots, bug stains, etc.

NOTE: The Wax & Polishing Solution

containers shown in the illustrations are

representative. Yours may look different,

A

Place the b/ue wax app/icator bonnet on

pad as shown. Make sure the elastic is

tucked down securely and evenly arour_d

the underside of the pad.

B FOR PASTE WAX

Spread about a heaping teaspoonful of wax

evenly over the entire surface of the wax

app/icatorbonnet. Use a putty knife or any

flat object. DO NOT APPLY WAX DIRECTLY

TO CAR.

3

C FOR LIQUID WAX

Apply three swirls of liquid wax on the wax

applicator bonnet. DO NOT APPLY WAX

DIRECTLY TO CAR. This first application

should do about 1/4 of the car. The bonnet

will not absorb as much when reloading.

E

After fiat surfaces are covered with wax,

do sides of the car. Hold the polisher as

shown. Let the cord hang free. It is not

necessary to use a criss-cross motion on

doors and fenders.

D

ALWAYS START AND STOP THE

POLISHER ON OR AGAINST THE

SURFACE.

Place the extension cord over your

shoulder and do flat surfaces first--hood,

trunk and roof. Cover areas quickly with

broad, sweeping strokes in a criss-cross

pattern.

DO NOT press down on the polisher.

The machine's action, not pressure,

does the best job.

1:3

!

LEFt" ! RIOHT

,...L,--

_o4

F

Remove the wax applicator bonnet and

use it to hand-poUsh all hard-to-reach

surfaces; under the bumpers, around the

door handles, etc.

G

Throw away the wax appficator bonnet

and put a clean terrycloth bonnet on the

polisher.

H

Polish the wax in the same order it was

applied. Use long, sweeping strokes in

criss-cross pattern. Do not press hard. l

the polisher do the work.

4

•Terrycloth bonnets are 100% cotton and

can be machine-washed in cold water

with a small amount of detergent, then

machine-dried at low heat. However,

hand-washing and air drying is recom-

mended for longer terrycloth bonnet life.

• Wax applicator bonnets are to be used

only once, then thrown away.

• To prolong pad life and shape, always

store polisher with pad face up.

• Remove bonnet from pad when polisher

is not in use so that pad can dry out and

retain its original shape.

•DO NOT USE ABRASIVE

COMPOUNDS.

•The most common error is applying too

much wax. If pad becomes saturated, it

will not last as long, and polishing will

be more difficult and take longer.

• If applicator bonnet continually comes off

pad, you may be using too much wax.

•If buffing seems difficult, you may have

used too much wax.

• Use only mild soap and a damp sponge

to clean polisher. Do not immerse any

part in liquid. If polisher needs repair,

use only identical replacement parts

illustrated and listed on Page 6.

• The polishing bonnet is only to be used

for the final buff. Do not use it to apply

or remove wax.

•Polishing bonnets can be cleaned by

hand washing in lukewarm water and

mild detergent; then machine dry at the

lowest setting.

TO REPLACE PAD ASSEMBLY

Holder

Counterweight

5/16" _:_

Le_-Threaded

Bolt

(1/2"Head) Loosen

1. Insert screwdriver through aperture

between polisher and pad, and brace

against counterweight.

2. Remove center bolt with 1/2" deep wel

socket wrench, turning clockwise.

3. Replace pad assembly and turn bolt

counterclockwise.

FULL ONE YEAR WARRANTY

If this product fails due to a defect in material or workmanship within one year from the date of

purchase, Sears will at its option repair or replace It free of charge.

Return this product to aSears Service Center for repair, or to place of purchase for

replacement. Note: Bonnets and foam sponge rubber pad are expendable items and are not

covered by this warranty.

If this product is used for commercial purposes, this warranty applies for only 90 days from the

date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

Sears Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

5

6

II

7

,_--11

KEY PART

NO. NO.

1 41P26217

241P25500

2A 41P25009

3 41P16205

4 41P1.4017

5 41P26038

641P21000

6A 41P18017

6B 41P22000

6C 41P90000

DESCRIPTION QTY.

Housing top 1

Cord strain relief assy. 1

Switch lead wire 1

Cord retainer 1

Switch set (switch,

button, spring) 1

Housing bottom 1

Motor assy. 1

Motor through bolts

washer_ lock washers 2

End bell assy. 1

Motor brush set

(brushes, clips,

srpings) 1

KEY

NO.

6D

6E

6G

6H

7

8

i9

10

11

PART

NO.

41P21500

41P23200

41P23000

41P18501

41P16307

41P17000

41P27016

41P18024

41P90500

41P58071

DESCRIPTION QTY.

Armature 1

Magnet, yoke assy. 2

Motor plate assy. 1

Motor bearing 1

Guard 1

Counterweight 1

Pad/Padholder assy. 1

Left-handed

threaded bolt 5/16" 1

Hardware pkg. 1

Owner's manual 1

R

H :. H.:: ¸

".:::;::.:::::

H

!i_iiiiii!!i!i

For repair of major brand appliances in your own home...

no matter who made it, no matter who sold itE

1-800-4-MY-HOME sM Anytime, day or night

(1-800-469-4663)

www.sears.com

To bring in products such as vacuums,

lawn equipment, and electronics for repair, call for

the location of your nearest Sears Parts & Repair Center.

1-800-488-1222 Anytime, day or night

iiiii!iiill

!i:i!i_i:ii_i:

_HHH_

H_H

_H

i!:_iiiii!il

i!iiiii!iiii

_:iiii:ii:i:!ili:_

www.sears.com

For the replacement parts, accessories and owner's manuals

that you need to do-it-yourself, call Sears PartsDirectS"!

1-800-366-PART sM

(1-800-366-7278)

www.sears.com/partsdirect

To purchase or inquire about a Sears Service Agreement:

1-800-827-6655

7 a.m. - 5 p.m. CST, Mon. - Sat.

Para pedir servicio de reparaci6n a domicilio,

y para ordenar piezas con entrega a domicilio:

1-888-SU-HOGAR sM

(1-888-784-6427)

SWA S

HomeCentral s"

iiiiiiiiiiii

:i:i:i:i:!:i

!ii!!iii!i!il

iiiiiiiiii_i

iiiiiiiiiiii_

ii!iiii!iiii_

::::::::::::

:+:+::_

!!ii!i!i_i_i

:i:1%i_

...,......

::.::_:::::"

::::::::::/

::::::::::::

iiiiiiiilili_

:::::::::::._

,...,...,

,.,.......

........y.

:.:.:,:,:.:,:

.......,.. _.

. .......,

ii_iiiiiiiii:

i!iiiii_ilili

iiiiiiiiiiii_

:+;+::.:

6 a.m. - 11 p.m. CST, iiii!iiiiiiii

7daysaweek iiii!iiiiiiii

,.......

. .....

iiii!iiiiiii!

!_!ii;i!i_ill

iiiiiiiiiiiii

iiiii!ii!iiii

iiiilili!iii!

iiiiiiiiiiii!

pour service en fran_ais: iiiiiiiiiiii

1-877-LE-FOYER s_ iiiiiiii;iii

(1-877-533-6937) _ii!iiiiii!i

. ..,....

.....

,.......

:.:,:.:.:.:

........

:.:.::_:

::::::

;!:i:i:i:i:!

i i i iii i iii i!i!!iii!iiiii !i iiiiiiiiiiiiiiiiiii!iii!i iiiiiiiii!iii!i!iii ! ! i i i i iii iiiiiiiiiiiiiiii

©2000, Sears, Roebuck and Co. ® Registered Trademark P'" Trademark of Sears, Roebuck and Co.

58-071 ® Marca Registrada ft. Marca de F_brica de Sears, Roebuck and Co Printed in Mexico